the User Manual for this product
Contents
1. 4 Instructions for the installer The following instructions are aimed at the qualified installer to ensure that he carries out the installation adjustment and maintenance operations as correctly as possible and according to current legal regulations Any operation must be performed with electrical power cut to the appliance Before using the appliance carefully remove the special adhesive film protecting the parts in Stainless steel Do not leave any glue residues on the surtaces If necessary remove them at once with an appropriate solvent Positioning Position the appliance perfectly horizontally on a table or similar support the table or support must be at least 85 cm above the floor Position it at a distance of not less than 10 cm from the side and rear walls to enable natural ventilating air to circulate freely around it The appliance is ventilated through specitic openings on the metal walls of the outer housing and ensures efficiency and long life For this reason it is strictly forbidden to obstruct these ventilation openings even partially or for short periods Failure to observe this specific prohibition releases the manufacturer of the appliance from all responsibility and immediately voids any guarantee rights for the said appliance because its constructive conformity has been voluntarily compromised Furthermore the appliance is not suitable for embedding and for grouped positioning with other identical a2. EKF 464 3 GRILL Fig 1 Programmer indicator light Temperature indicator light Umidifier switch ON OFF GRILL switch for predisposed models GRILL OFF position O GRILL ON position 1 Programming cooking time To run the oven turn the programmer knob Fig 1 in line with symbol W continuous operation or in line with the selected cooking time up to 120 minutes In the second case end of cooking Is signalled by the oven switching OFF automatically Programming cooking temperature Turn the knob of the adjustment thermostat Fig 2 in line with the temperature selected for cooking Humidifier key To produce vapour inside the oven while the oven is operating and the chamber is hot press the key commanding the humidifier for a few seconds Control thermostat indicator light The control thermostat orange indicator light goes OFF whenever the programmed temperature is reached inside the cooking compartment It lights up again when the thermostat is tripped to re establish this temperature End of cooking programmer indicator light The programmer green indicator light indicate that the oven is operating and that cooking time Is active Oven internal light The light is always on when the oven is operating To switch off the oven Turn OFF the knobs of the end of cooking programmer and of the thermostat When you have finished using the oven shut off the water ON OFF ta
3. nan A er ote AA and 2 TIT TTI TTI GEE REE RE RE NEF AEF TER TEE LEER HE piran Hi CCC anman m 5555 5558 finn m j CECI m He n ren Fi CO CLE ETE ry eee iy Cite HHH a im NNT E E n E m Yon HHHH CCC n ttt EE pEsesess nmm HT nn SE n A an fi aE ot ae tt in PTCCLOeeeeeeCLL tir tir n rt rin mi HHHH j HEN H GA ri Lafi ATIL LU te HH H HHH Fa EEEE oH jenn LELLO Ganan lescce Gang TE E E kn ECE PEE Eee Eee USE AND INSTRUCTION MANUAL MODD EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL rev 2 2 T gt O O a O p ro Ses WO A E no So LI Oo O mn Z M U LLI hou C fe O Q e T gt gt E mail info tecnoeka com Tel 39 049 9300344 39 049 5791479 Fax 39 049 5794387 www tecnoeka com TECNOEKA SRL VIA MARCO POLO 11 35010 BORGORICCO PADOVA ITALY TEL 39 049 5791479 39 049 9300344 FAX 39 049 5794387 E MAIL INFO TECNOEKA COM WWW TECNOEKA COM WWW TECNOEKA RU COD FISC P IVA 00747580280 REA N 133205 CAP SOC EURO 119 000 00 I V CE DECLARATION OF CONFORMITY Annexed document Il A of directive 2006 42 EC Model EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL TECNOEKA Srl declares that the mentioned above products meet the following satety regulations Low voltage directive 20
4. cannot be held responsible for any damages either direct or indirect to people pets or property caused by the appliance breaking down or following its non use The Manufacturer cannot be held responsible for any inaccuracies due to misprints or mistakes in copying in this handbook The Manufacturer reserves the right to modify the products as he deems fit also in the interest of the user without affecting the vital characteristics of functionality and safety page 15
5. to the appliance before every operation General cleaning Clean the oven when it is cold Wash enamelled parts with lukewarm water and soap do not use abrasive products steel wool or acids which could ruin them To clean the steel parts do not use products containing chlorine sodium hypochlorite hydrochloric acid etc even if diluted Use specific off the shelf products or a little hot vinegar Rinse thoroughly with water and dry with a soft cloth Clean the glass door of the oven with hot water only and do not use rough cloths Do not allow foods especially acid foods such as salt vinegar lemon etc to Stagnate on the stainless steel parts because they could deteriorate Do not wash the appliance with direct jets of water because if water enters this could limit the appliance s safety Do not use corrosive substances e g hydrochloric acid to clean the oven s support bench Cleaning the oven It is good practice to clean the oven interior at the end of every day of duty In this way it will be easier to remove cooking residues preventing them from burning when the oven is next used Clean it accurately with hot water and soap or with the appropriate oft the shelf products Cleaning the oven door To clean the oven door thoroughly proceed as follows fully open the door attach the rings A onto the hinge seats Fig 3 lift the door gently and withdraw it Fig 4 Fig 5 Replacing oven lamp Electricall
6. 06 95 CE Electromagnetic compatibility Directive 2004 108 CE TECNOEKA Srl declares that the mentioned above products meet the following harmonised Standards CEI EN 60335 1 CEl EN 60335 2 42 CEI EN 55014 1 CEI EN 61000 3 2 CEI EN 61000 3 3 CEI EN 62233 TECNOEKA Srl declares that the mentioned above products meet the following directives Machine Directive 2006 42 CE Directive on the general safety of products 2001 95 CE Directive on the restriction in the use of dangerous substances in electrical and electronic appliances 2011 65 CE Directive on waste from electrical and electronic appliances 2002 96 CE RAEE TECNOEKA Srl declares that the mentioned above products meet the CE 1907 2006 REACH Regulation eo Borgoricco 05 09 2014 Signature of a Representative of he Board of directors CRISTINA LORA Electric Ovens rev 2 eee EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL X Sgq PRODOTTI Fam 1 FORNNFORNO ELETTRICO LEKa MANUALI D USO Forno Elettrico 40 60 90 LEka Lingua Inglese NUOVA GAMMA EF instruction manual EKF 411 EKF 464 EKF 416_000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL GB rev 2 doc TECNOEKA Srl 10 11 12 13 14 Index Technical service General warnings Technical specifications Instructions for the installer Use instructions for the user Residual risks for the user How to use the control panel Ov
7. Failure to observe this prohibition invalidates any responsibility of the manufacturer of the machine The appliance is intended for professional use and must be utilised by qualified personnel trained to use it Any modification which may be necessary on the electrical system to enable installation of the appliance must be carried out solely by competent personnel Itis dangerous to modify or attempt to modify the characteristics of this appliance Never clean the appliance with direct water jets because If any water enters it could limit the machine s safety Before doing any maintenance or cleaning jobs disconnect the appliance from the electrical mains and allow it to cool When the tilting door is wide open do not put anything on the surface because the door hinges could be irreparably damaged Do not attempt to carry out the periodic controls or any repairs by yourself Contact the nearest Service Centre and use only original spare parts N B Improper or incorrect use and failure to observe the installation instructions shall release the manufacture from all responsibility In this connection the directives in the POSITIONING paragraph must be strictly observed TECNOEKA Srl use and instruction manual F EKF 416 000 es pen n The noise level of the appliance in operation is below 70 aB A The technical data plate is positioned on the rear panel of the appliance 3 Technical specifications
8. en cooking Cooking advice Routine cleaning and maintenance Technical assistance Informations to the consumers Wiring layouts The Warranty use and instruction manual Electric Ovens rev 2 eee EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL 1 Technical service A technical check up once or twice a year helps prolong the life of the appliance and guarantees better operation Make sure that assistance is carried out solely and exclusively by qualified personnel For any spare parts orders or for any information about the appliance always mention the serial number and model data indicated on the technical data plate at the rear of the oven 2 General warnings Very important keep this instruction book together with the appliance for future consultation These warnings were drafted for your safety and for that of others Please read them carefully before installing or using the appliance If on receipt of the goods the packaging is damaged write the following on the delivery note REVERSE THE RIGHT TO CONTROL THE GOODS specity the damage and get the driver to sign in acceptance send a claim in writing to the seller within 4 calendar days trom the date of receipt No claim shall be accepted after such period The warehouse inside temperature must not be lower than 9 C otherwise the thermostat regulation and safety thermostat control devices of the machine will be damaged
9. gative effects on the environment and public health which would be caused by incorrect management of the rubbish Should the user dispose of the product abusively administrative sanctions would be applied Electric Ovens rev 2 13 Wiring layouts MODD EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL M Power terminal board Pr End of cooking programmer MI Door microswitch Umiditier switch TI Safety thermostat T2 Control thermostat L1 L2 Lighting lamps Key R1 R2 Circular heating elements V1 V2 Radial motoventilators V3 Motoventilatore tangenziale E Water solenoid valve B1 B2 Contactor coils S1 Programmer indicator light S2 Thermostat indicator light Pr MI T1 T2 R1 R3 TECNOEKA Srl use and instruction manual MODD EKF 411 5 GRILL EKF 464 3 GRILL Y V2 Key Power terminal board L1 L2 Lighting lamps End of cooking programmer V1 V2 Radial motoventilators Door microswitch V3 Motoventilatore tangenziale Umiditier switch E Water solenoid valve Safety thermostat B1 B2 Contactor coils Control thermostat B3 Relais coil GRILL switch S1 Programmer indicator light R2 Circular heating elements S2 Thermostat indicator light Grill heating element Electric Ovens rev 2 00 eee EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL 14 The Warranty Your appliance i
10. hen placing tood in the cooking compartment leave a space of at least 40 mm between pans in order not to over obstruct air circulation Do not use pans with higher than necessary edges edges are barriers which prevent the circulation of hot air Warm up the oven before every cooking operation to obtain maximum uniformity Do not salt foods in the cooking compartment 6 Residual risks for the user After a cooking operation open the door cautiously to avoid a violent outflow of heat which could cause burns While the oven is in operation pay attention to the hot zones marked on the appliance of its external surfaces Place the machine on a bench or similar support at a height of at least 85 cm from the floor The bench or support must be able to support the weight of the machine and house it correctly The appliance contains electrical parts and must never be washed with a jet of water or steam The appliance is electrically connected before attempting any cleaning operation cut power to the appliance To prevent incorrect connection of the appliance the relevant electrical and water connections are marked by identification plates Do not use the door handle to move the appliance the glass panel may break When the tilting door is wide open do not use the internal surface to place objects to avoid damaging permanently the door hinges Electric Ovens rev 2 eee EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL
11. k Connection to the water mains The appliance must be fed with softened drinking water with hardness from 0 5 F to 3 F it is obligatory to use a softener to reduce the formation of lime inside the cooking chamber and pressure in the range from 100 to 200 kPa 1 0 2 0 bar Connection to the water mains should be made through the threaded 3 4 solenoid valve on the rear on the bottom of the appliance fitting in between a mechanical filter and an on off tap before you connect the filter allow a certain quantity of water to flow out in order to drain any waste from the pipe Connecting the power cable To access the terminal board just remove the appliance s rear side panel Loosen the cable gripper and allow the cable to pass through it Arrange the conductors so that the earth conductor is the last to detach from its terminal if the cable goes into a state of faulty traction Connect the phase conductors to the terminals marked L1 and L2 connecting the neutral conductor to the terminal marked N and the earth conductor to the terminal marked with the symbol according to the following lay out 400V 2N this electrical connection lay out is located near the power supply terminal board Tighten the cable gripper and re fit the rear side panel of the appliance The appliance must be connected to an equipotential system whose efficiency must Tirst be checked according to current legal regulations This connection
12. must be made between different appliances by using the appropriate terminal marked with the symbol The equipotential conductor must have a minimum diameter of 2 5 mm The equipotential terminal is at the rear of the appliance TECNOEKA Srl use and instruction manual Safety thermal breaker The appliance has a manually reset safety thermal breaker It protects against excessive dangerous over temperatures which could be accidentally generated inside the appliance This device is located on the back of the oven 5 Use instructions for the user This appliance is not intended for use by persons including children with reduced phycal sensory or mental capabilities or lack of experience and knowledge Unless they have beengiven supervision or instruction concerning use of appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance For first use we advise you to let the appliance to run load free at maximum temperature for about one hour In this way any unpleasant smells due to thermal insulation and residual work grease are eliminated This appliance must be used solely for the purpose for which it was expressly designed i e cooking foods in the oven Any other use is considered unsuitable The appliance can be used for all oven cooking of deserts pizzas meat fish vegetables as well as for gratinating and for re conditioning cooled and frozen foods W
13. nner not compliant with the instructions given in the user s handbook supplied with the product 6 tampering with the product 7 adjustments and or maintenance and or repairs carried out by unauthorised personnel and or with non original spare parts 8 inadequate or careless maintenance of the product in contrast with the user s handbook supplied with the product 9 damages caused by fire natural disasters and accident as well as by any cause not attributable to TECNOEKA SRL The warranty explicitly excludes varnished or enamelled parts knobs handles movable or removable plastic parts bulbs glass parts refractories and any accessories TECNOEKA SRL cannot be held responsible for any damages either direct or indirect caused by the product breaking down or following its non use Any repairs carried out during the warranty do not cause said warranty to be extended or renewed Nobody is authorised to modify the terms and conditions of the warranty or to issue new verbal or written warranties The warranty is valid only for appliances installed in the European Union Any dispute shall be settled by the competent Court in Padua Warning for the Buyer 1 the cooking appliance is designed only for cooking purposes while the heating appliance is designed only for heating domestic environments 2 TECNOEKA S r l does not install the appliances the seller shall be responsible for any installation carried out 3 TECNOEKA S r l
14. p upstream of the appliance and cut out electric power 8 Oven cooking For cooking betore putting food in warm up the oven to the required temperature When the oven reaches the temperature put the food in and check cooking time Switch off the oven 5 minutes before the theoretical time in order to recover stored heat page 9 TECNOEKA Srl use and instruction manual Convection cooking Activate the oven and turn the thermostat knob in line with the required temperature Defreezing Activate the oven and turn the thermostat knob to the OFF position Humidification While the oven is functioning press the humidification botton to generate steam in the already heated cooking chamber 9 Cooking advice Convection cooking Heat is transferred to the foods by pre heated air forced to circulate by in the cooking chamber The heat quickly and uniformly reaches all parts of the chamber enabling simultaneous cooking of different types of food providing they have the same cooking temperature placed on the shelves without mixing tastes and smells Convection cooking is particularly convenient for rapid defreezing and for sterilising preserves and drying mushrooms and fruit Cooking with the ventilated grill for predisposed ovens Forced circulation of air is combined with thermal radiation produced by the grill and this allows heat to gradually penetrate the inside of the food without burning the surface Cooking desserts Desse
15. ppliances Electric Ovens rev 2 eee EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL Electrical connection The appliance must be connected to the electrical mains according to current legal regulations Before making the connection make sure of the following the voltage and frequency values of the power supply system match the values on the technical data plate affixed on the appliance the limiting valve and the system are able to support the appliance s load see the technical data plate the power supply system has an adequate earth connection according to current legal regulations aomnipolar switch with minimum between contacts aperture of the overvoltage category lll 4000 V sized to the load and conforming to current legal regulations is fitted between the appliance and the mains in the direct connection to the mains the omnipolar switch used for connection is easy to reach when the appliance is installed the yellow green earth wire is not interrupted by the switch the power supply when the appliance is operating must not deviate from the rated voltage value by 10 make sure that after inserting the power supply cord into the terminal block it does not come into contact with any of the cooking range s hot parts if the supply cable is damaged then it must be replaced by the manufacturer or by your technical support or by a qualified person to avoid any ris
16. rts require a very high temperature usually from 150 to 200 C and a pre heated oven about ten minutes The oven door must not be opened until at least 3 4 of the cooking time has elapsed Whipped dough must be difficult to detach from a spoon because excessive fluidity would prolong cooking time to no avail Cooking meat Meat to be cooked should weight at least 1 Kg to prevent it drying too much Very tender red meats to be cooked rare which must be cooked on the outside to keep all their gravy require short cooking time at high temperature 200 250 C The gravy ingredients must be placed immediately in the pan only if the cooking temperature is brief otherwise they should be added during the last half hour You can check the degree of cooking by squashing the meat with a spoon if the meat does not yield it is correctly cooked For roast beef and fillet which must remain pink inside cooking time must be very brief Meats may be placed on a plate Suitable for oven cooking or directly on the grill under which you should place a tray to collect the gravy When cooking has finished we advise you to wait for 15 minutes before cutting the meat so that the gravy does not come out Before being served the dishes may be kept hot in the oven at minimum temperature page 10 Electric Ovens FEV 2 0 eee EKF 411 EKF 464 EKF 416 000 EKF 416 3 EKF 411 3 GRILL EKF 464 3 GRILL 10 Routine cleaning and maintenance WARNING Cut power
17. s covered by warranty The seller will replace or repair and his decision will be final free of charge for the customer only those parts that are defective due to a manufacturing fault on condition that under penalty of forfeiture for domestic equipment the customer notifies the fault within two months from the date when he she discovered it and anyway within 2 years form the date of purchase for professional equipment the customer notifies the fault within 8 days from the date when he she discovered it and anyway within 12 months from the date of purchase by registered letter with acknowledgement of receipt and enclosing the invoice or receipt proving the purchase Apart from the case when the customer cannot produce the invoice or receipt proving the purchase or when the above mentioned terms are not complied with the warranty is expressly excluded in the following cases 1 faults or breakage caused by the transport 2 wrong or incorrect installation of the product for instance because of insufficient draught of the flue or exhausts in light of the instructions given in the user s handbook supplied with the product 3 inadequate or abnormal electrical hydraulic and or gas supplies 4 carelessness negligence or incompetence in using the product in light of the instructions given in the user s handbook supplied with the product 5 use of the product for uses different from the one for which it was built or anyway in a ma
18. y switch off the appliance unscrew the protective glass cap Fig 5 unscrew the lamp and replace it with another lamp suitable for high temperatures 300 C with the following characteristics Voltage 230 240 V Power 15 W Fitting E 14 Refit the glass cap and power up the appliance page 11 TECNOEKA Srl use and instruction manual 11 Technical assistance Before leaving the factory the appliance was completely regulated and tested by expert specialised personnel to guarantee the best operating results All repairs and settings must be performed with utmost care and attention respecting national safety regulations in force Always contact your retailer or our nearest Service Centre giving details of the problem the appliance model and the serial number on the rating plate on the rear panel For any maintenance the user can contact Tecnoeka by calling the teleohone numbers on the cover or going to www tecnoeka com 12 Informations to the consumers Further to Directive 2002 96 EC the symbol of the crossed rubbish skip on the appliance means that at the end of its life the product must be disposed of separately from the other rubbish The user must hand the appliance to a specialised waste collection centre for electric and electronic equipment The separate collection of the rubbish and subsequent treatment recovery and disposal help to produce other equipment using recycled materials reducing the ne
Download Pdf Manuals
Related Search