Centrale Elettronica Lrx 2149
Contents
1. LEDs LED on option stored LED off option not stored Flashing LED option selected Reference LED LED Off No code Motor time 2 minutes LED On TX Pgm code Pgm motor time Pgm Wind safety 1 CODE 2 T MOT 3 WIND SPEED Wind safety 25 km h 4 SUN SENSOR Sun sensor OFF Sun sensor ON 5 RAIN SENSOR Rain sensor OFF Rain sensor ON 6 SUN Sun Presence No Sun Presence Yes 7 RAIN Yes 8 R HEAT Rain Presence No Rain Presence R Heat No R Heat Yes 1 CODE Radio control programming Programming using a 1 or 2 button radio control To programme the transmission codes in the radio control proceed as follows press the SEL key the CODE LED begins to flash Send the first preselected code using the relevant ra dio control at the same time when the CODE LED begins to flash rapidly send the second code to be stored The CODE LED will remain lit and the programming will be complete If the second code is not sent within 10 seconds the control unit exits the programming stage selecting the function using a single button on the radio control If you have stored 10 codes and you repeat the programming operation all the indicator LEDs will start flashing extremely rapidly to indicate that no more codes can be stored Programming using a 3 button radio control from the Be Free series The control unit allows you to store the whole BeFree radio control by programming only the U2. control unit must be permanently connected to the power supply network and is not equipped with any type of 230 V a c electric line sectioning device The installer is responsible for installing a sectioning device in the system An omnipolar switch with overheating category III must be in Stalled It must be positioned in such a way that it is protected against accidental closures For connections power supply and outlet contact we rec ommend the use of flexible wires with an insulating sheath in harmonised polychloroprene HO5RN F The wires should have a minimum cross section of 0 75 mm Fasten the connection cables using the cable clamp sup plied with the product kit Handle the control unit with care during the installation process and make sure that all components are properly assem bled Pay particular attention to the ceramic plate and the flat connection cable When closing the box again it must fold back on itself normally It is very important to establish an exact location so that the product is exposed to weather conditions it can control _ Fix the device to the wall using the screws and rawlplugs supplied with the product in the correct position see figure below Make sure that the contro unit remains tilted at approxi mately 45 degrees Fixing area at the top round end of the box at the bottom Do not paint or varnish the sensitive surface of the control unit The dirt which accumulates on the sur
3. BeWeather Electronic Control Unit GB procedure remains the same for the downward move An electronic control unit integrated into the Wind Sun and Rain Sensor compartment for the automation of sun blinds and rolling window shutters with the possibility of radio control operation for individual and or centralised control Mod BeWeather 306 306 MHz Mod BeWeather 330 330 MHz Mod BeWeather 418 418 MHz Mod BeWeather 433 433 92 MHz Mod BeWeather 433 SET Narrow Band 433 92 MHz Mod BeWeather 868 Narrow Band 868 3 MHz Product intended for those countries where its use is per mitted TECHNICAL DATA Power supply 230V 50 60Hz 600W Max Motor output 230V 500W Max Operating temperature 10 55 C Radio receiver see model Compatible radio controls 12 18 Bit or Rolling Code Anemometer sensitivity 5 40 Km h Sun sensor sensitivity 5 40 Klux Number of codes that may be stored 10 Max Packaging dimensions 240 x 185 x 110 mm Container PC UL94V 0 IP54 ment phase Operation using a 3 button radio control BeFree x1 The following type of operation is obtained using the BeFree x1 radio control the Up button controls the upward movement until the end of the motor time the Stop button causes all movement to stop and the Down button controls the down ward movement If a stop command is sent during the upward or downward movemen
4. NDITION It is also possible to enter two identical codes buttons from one radio control onto all the control units or a group of them which are situated at a maximum distance of 20 metres from the point of command in order to obtain general or partial mo tion of more than one automation The device can only operate in conjunction with one or more radio controls There is no radio control code stored in the de fault factory setting ANEMOMETER OPERATION OPERATION USING DIFFERENT MODELS OF RADIO CONTROL The electronic control unit will cause the sun shade to move upwards every time the wind exceeds the selected threshold Different models of radio control may be programmed By stor ing a code 1 button a cyclic step by step operation Up Stop Down may be achieved and by storing two different codes 2 buttons different commands are produced one for Up and one for Down Storing three different codes 3 BeFree series but tons produces three different commands the first for Up the second for Stop and the third for Down Operation using a 1 button radio control The following type of operation is obtained using a radio con trol with a single button the first press controls the upward movement of the shutter until the motor timer stops The sec ond press controls the downward movement of the shutter If the button is pressed before the motor stops running the con trol unit will stop th
5. P button To programme the BeFree radio control codes follow this procedure press the SEL key the CODE LED begins to flash Press the UP key of the desired radio control at the same time at that moment the CODE LED will remain lit and program ming will be complete If all of the possible 10 radio control codes have been stored and you repeat the programming op eration all indicator LEDs will start flashing very rapidly to indi cate that no new codes can be stored Deleting the codes To delete all transmission codes stored in the memory proceed as follows press the SEL but ton the CODE LED starts flashing Then press the SET button the CODE LED switches off and the procedure is complete 2 T MOT Motor Timer Programming The control unit comes with a motor power supply time of two minutes T MOT LED OFF The motor time must be programmed when the shutter is down and in the following way Press the SEL key until the T MOT LED key flashes then hold down the SET key the shutter will begin to move upwards Once the desired position has been reached release the SET key at this very moment the motor time will be stored and the T MOT LED will remain lit If you are using an automation which has a stop limit we rec ommend that you set a time which exceeds the stop limit of the shutter by a few seconds If you want unlimited motor time perform the same program ming procedure holding down the SET key for les
6. The Sun Sensor may be enabled in the following way press the SEL key until the SUN SENSOR LED flashes then press the SET key briefly at this moment the SUN SENSOR LED remains lit and the Sun Sensor will be enabled Repeat the op eration to disable the Sun Sensor Enabling the Sun Sensor using a 3 button radio control BeFree x3 X6 The Sun Sensor may be enabled in the following way hold down the key on the radio control that was programmed previously for 5 seconds at the same time the control unit will cause the shutter to move Up Down for 1 second to confirm that the Sun Sensor has been enabled and the SUN SENSOR LED will remain lit Repeat the operation to disable the Sun Sensor by following the same procedure but instead holding down the key for 5 seconds 5 RAIN SENSOR Rain Sensor ON OFF Disabling the Rain Sensor The control unit comes with the Rain Sensor enabled RAIN SENSOR LED ON The Rain Sensor may be disabled in the following way press the SEL key until the RAIN SENSOR LED flashes then press the SET key briefly at this moment the RAIN SENSOR LED switches off and the Rain Sensor will be disabled You can re peat the operation to enable the Rain Sensor EXTENDED MENU The control unit is supplied by the manufacturer with the option of selecting only the functions listed in the main menu To enable the functions of the extended menu proceed as fol lows press the SET key and hold for 5 s
7. e shutter moving and the button will need to be pressed again to reactivate the motor in the opposite direc tion Operation using a 2 button radio control By using a radio control with 2 buttons the following processes may be carried out the first button Up controls the upward movement until the motor has stopped running and the sec ond button Down controls the downward movement of the shutter If the upward movement is interrupted with another Up command the motor will continue to run in the upward movement direction If however the movement is interrupted with a Down command the control unit will stop the motor SUN SENSOR OPERATION The electronic control unit controls the downward movement of the sun shade after 5 minutes during which the brightness is greater than the threshold selected using the VR1 trimmer and displayed when the SUN LED lights up it also controls the up ward movement of the shade after 5 minutes during which the brightness is below the selected threshold Sun sensitivity adjustment 5 40 Klux The control unit allows you to adjust the sensitivity of the Sun Sensor using the VR1 trimmer When the SUN LED lights up on the control unit this indicates that the intensity of the sun exceeds the selected threshold this enables you to use the current light conditions as a reference when setting the desired value RAIN SENSOR OPERATION The electronic control unit wi
8. econds the SUN RAIN and R HEAT LEDs will flash and the user has 30 sec onds within which to select the functions of the extended menu using the SEL and SET keys After another 30 seconds the control unit returns to the main menu gt CODE remote PGM OFF remote PGM O Z T MOT Aut movement lock OFF Aut movement lock W Zz WIND SPEED Safety upward OFF Safety upward SUN SENSOR RAIN inversion OFF RAIN inversion O C ON D O Zz RAIN SENSOR Aut movements 5 min n SUN RAIN R HEAT Aut Movements 10 3m Flashing beacon ON OFF Flashing beacon ON OFF Flashing beacon ON OFF A CODE Remote programming of radio control The control unit allows the transmission code to be pro grammed by remote without using the SEL key To programme the transmission code remotely proceed as follows send the radio control code continuously for more than 10 seconds and the control unit will enter the programming mode as described above for the CODE LED in the main menu The control unit is supplied by the manufacturer with remote programming of the transmission code not enabled to enable the function proceed as follows check that the extended menu is enabled SUN RAIN and R HEAT LEDs flash using the SEL key navigate to CODE LED when flashing and press the SET key the CODE LED lights up permanently and pro gramming is completed Repeat the operation to restore the previous c
9. face of the rain sen sor restricts its sensitivity we therefore recommend that it is cleaned once or twice a year using a damp cloth after the electricity supply has been disconnected Connect the earth wire of the motor to the earth wire of the electrical system using the special terminal on the control unit as illustrated in the connection diagram For the radio receiver to operate correctly when two or more control units are used we recommend that you install the devices at least 3 metres away from each other FOR THE USER IMPORTANT The device should not be used by children or by individuals with reduced physical or psychological abilities unless supervi sion is provided or instruction given on how to operate it Do not let children play with the device keep radio controls out of their reach CAUTION Keep this instruction manual in a safe place and adhere to the important safety instructions contained within it Non adherence to these instructions may lead to property damage and serious accidents Examine the system frequently to check for any signs of damage Do not use the device if it needs to be repaired Warning All operations which require the casing to be opened such as wire connection programming etc must be carried out during installation by skilled staff only For any other procedure which requires the casing to be opened again re programming re pairs or site modifications please con
10. he tests Warning after you have tested the sensors restore the Dip 1 and 2 in the desired operation mode Anemometer manually turn the Anemometer blades at the same time the control unit will cause an upward movement lasting 5 seconds Sun sensor turn the VR1 trimmer as far as possible in a clockwise direction in the position at the same time the control unit will cause the SUN LED to light up and there will be a downward movement lasting 5 seconds Turn the VR1 trim mer in an anticlockwise direction in the position at the same time the control unit will cause the SUN LED to switch off and there will be an upward movement lasting 5 seconds Rain sensor get the sensitive part of the Rain Sensor wet at the same time the control unit will cause the RAIN LED to light up and there will be an upward movement lasting 5 seconds When you have completed the test make sure you have dried the sensitive part of the rain sensor before using the control unit in the normal operation mode PROGRAMMING BUTTONS AND INDICATOR LEDS SEL button selects the type of function to store selection is indicated by the LED flashing The desired function can be se lected by pressing the button repeatedly The selected function remains active for 15 seconds flashing LED following which the control unit returns to its original status SET button programmes the function that has been selected using the SEL Key Indicator
11. ll cause the sun shade to move upwards as soon as the sensitive part of the rain sensor gets wet with water as displayed when the RAIN LED lights up OPERATION PRINCIPLES swi Swi swi swi Rev 1 2 31 01 08 Step by step P P Aut Sensors User Present Sensor Test 1 Step by step Dip 1 and 2 OFF The electronic control unit has a cyclic Step by Step logic whose operation depends on the type of radio control associ ated with it see operation with radio control with 1 2 3 but tons 2 Step by step Aut Sensors Dip 1 ON and Dip 2 OFF The electronic control unit allows the Step by Step operation as described above with the addition of the automatic control of the Wind and Rain sensors After the activation of one of the two sensors once the disturbance is over the electronic con trol unit controls the downward movement of the sun shade af ter 5 minutes 3 Manually controlled Dip 1 OFF and Dip 2 ON Using the radio control the User present operating mode can be obtained i e the control must be constantly enabled so that the blind or shutter can be moved as necessary The move ment stops when the control is released 4 Sensor Test Dip 1 and 2 ON The electronic control unit allows to check the sensor operation and the correct rotation direction upon installation we advise that you place the shade in intermediate position in order to verify the confirmation movements during t
12. ment inversion The control unit is supplied by the manufacturer with the Rain Control Upward Movement Control association that is to say when the rain sensor detects the rain the control unit controls the upward movement If you wish that the control unit controls the downward movement when rain is detected by the rain sensor proceed as follows check that the extended menu is enabled SUN RAIN and R HEAT LEDs flash using the SEL key navigate to SUN SENSOR LED when flashing and press the SET key the SUN SENSOR LED lights up perma nently and programming is completed Repeat the operation to restore the previous configuration E RAIN SENSOR Automatic sensor action Time The control unit is supplied by the manufacturer with the Auto matic sensor action Time of 4 minutes if you wish to set 10 minutes to reduce the motor movements proceed as follows check that the extended menu is enabled SUN RAIN and R HEAT LEDs flash using the SEL key navigate to RAIN SENSOR LED when flashing and press the SET key the RAIN SENSOR LED lights up permanently and programming is completed Repeat the operation to restore the previous con figuration RESET To reset the default configuration of the control unit press the SEL and SET buttons simultaneously all indicator LEDs will switch on and then off again immediately Rev 1 2 31 01 08 FOR THE INSTALLER IMPORTANT The BeWeather
13. onfiguration B T MOT Automatic movement lock The control unit enables the prevention of Automatic move ments Up Down sun blind movements on the Sun Sensor command or Automatic Sensors function so that if a Stop command is sent from a radio control during the movement the control unit momentarily locks the Automatic movements until a new Up or Down command is sent The control unit is supplied by the manufacturer with the Automatic Movement Lock disabled to enable the function proceed as follows check that the extended menu is enabled SUN RAIN and R HEAT LEDs flash using the SEL key navigate to T MOT LED when flashing and press the SET key the T MOT LED lights up permanently and programming is completed Repeat the operation to restore the previous configuration C WIND Safety Upward Movement The control unit is supplied by the manufacturer with the Safety upward movement function disabled if you wish to enable the function in such a way that after 12 hours of inactivity of the Wind Sensor the control unit automatically control the safety upward movement proceed as follows check that the ex tended menu is enabled SUN RAIN and R HEAT LEDs flash using the SEL key navigate to WIND LED when flash ing and press the SET key the WIND LED lights up perma nently and programming is completed Repeat the operation to restore the previous configuration D SUN SENSOR Rain control move
14. s than two seconds the T MOT LED will remain lit and the unlimited time function will be set The operation may be repeated if a mis take is made during programming 3 WIND Wind Safety Threshold Programming Displaying the programmed wind threshold The wind safety threshold may be displayed in the following way use the SEL key to navigate to the WIND LED position the LED will double flash the same number of times as the stored wind safety threshold each WIND LED double flash corresponds to an increase of 5 km h for example 5 WIND LED flashes 25 km h Wind safety threshold selection from 5 to 40 km h The control unit comes with a default wind safety threshold set ting of 25 km h WIND LED OFF The wind safety threshold may be programmed in the following way use the SEL key to navigate to WIND LED then press the SET key to start the programming procedure At the same time Rev 1 2 31 01 08 the WIND LED will begin to double flash each double flash of the WIND LED corresponds to an increase of 5 km h press the SET key once the desired threshold has been reached at this moment the selected value will be stored and the WIND LED will remain lit for example 5 WIND LED double flashes 25 km h The operation may be repeated if a mistake is made during programming 4 SUN SENSOR Sun Sensor ON OFF Enabling the Sun Sensor The control unit comes with the Sun Sensor disabled SUN SENSOR LED OFF
15. t the control unit causes this movement to stop If a command that is in the opposite direction to the current movement is sent during the upward or downward movement the control unit causes the shutter to change direc tion Operation using a 3 button radio control BeFree x3 X6 When using the BeFree x3 x6 radio control you will obtain the same operation as previously described for the BeFree x1 version in addition by using the keys and at the sides of the radio control it is possible to select the UP STOP DOWN controls for 3 different types of use BeFree x3 or for 6 different types of use BeFree x6 In addition by using the keys and at the sides of the radio control it is possible to enable and disable the sun sensor the selection is confirmed by a quick UP Down movement of the motor INVERSION OF THE ROTATION MOTOR CONNECTION OF CN 1 TERMINAL BOARD Earth 230 V line input Phase 230 V line input Neutral Upward movement motor output Shared motor output Downward movement motor output OU If you notice that when pressing the UP key on the radio control the control unit causes the shutter to move upwards instead of downwards simply repeat the programming proce dure pressing the DOWN key instead of the UP key or invert the motor s Upward movement wire and the Downward move ment wire GROUP OR GENERAL CENTRALISATION INITIAL OPERATING CO
16. tact the technical assis tance service hereby declares that the below products BeWeather Series conform to the specifications in the Directives R amp TTE 99 5 EC EMC 2004 108 EC LVD 2006 95 EC CE RAIN SENSOR MONITOR SUN SENSOR e 9 WIND SPEED SUN RAN R HEAT T MOT SUN SENSOR CODE eo fo 2 SEL SET Rev 1 2 31 01 08
Download Pdf Manuals
Related Search