Posey® Bed 8040, 8050, 8060 Assembly Instructions
Contents
1. 8040 Long Term Care A Frame Canopy Enclosure Installation PROCEDURE Posey Bed 8040 8050 8060 INTRODUCTION 6 0 090 09 09 6 6 6 6 6 6 6 6 6 6 6 gt This section provides detailed installation and setup instructions for the Posey Bed 8040 8050 and 8060 The installation steps must be followed correctly to ensure proper operation and service Read these Assembly Instructions carefully before attempting to assemble the bed Follow all instructions carefully select a place where sufficient clearance can be provided around the bed Ample working space is necessary around and above the bed The bed is heavy and large therefore it is strongly recommended that a second person assist with the assembly of the Posey Bed 8040 8050 and 8060 to provide stability and to help prevent injury The bed assembly portion requires two people 8050 All Care A Frame Canopy Enclosure 8060 All Care A Frame Canopy Enclosure Hospital bed and mattress not included e 0606060606060606 6 06 o 6 o 6 6 gt Gather assembly tools not included in the boxes Check Quantity Tool LJ 1 Box cutter LJ 9 16 combination wrenches or sockets www posey com 1 800 447 6739 5 INSTALLATION 6 666 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 9 Confirm that all parts have been included with the bed If any items are missing or damaged please contact Posey Technical Service at2. 09 0 09 0 09 06060606 09 09 09 0 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 The following bed types should NEVER be used with the Ka Bed A failure to follow this warning may result in serious injury or death from ENTRAPMENT or suffocation or from a fall or unassisted bed exit Residential type beds The canopy system of the Posey Bed is not designed to securely attach to residential type beds e Any hospital bed that cannot be lowered between sixteen 16 and seventeen inches 17 for the 8050 and 8060 model or thirteen 13 and fourteen inches 14 for the 8040 model to keep the canopy taut and avoid a blousing effect and excess material in the patient compartment which will increase the risk of entrapment or suffocation e Any hospital bed that allows the head to be raised to an angle greater than seventy degrees gt 70 Raising the head to a greater angle will damage the canopy and increase the risk of serious injury or death from a fall of unassisted bed exit Any hospital bed that does not securely attach to the Posey Bed with either 1 the four IV post mount brackets or 2 the Posey Bed universal straps as this may result in serious patient injury NEVER allow patient weight to exceed the maximum load of 300 lbs Mattress Installation 6 0 e 0 6 6 6 6 6 0 6 6 6 6 6 09 6 6 09 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 gt MATERIALS e Compatible hospital bed mattress see mattress size below e Assembled bed fra
3. 8040 8050 8060 Posey Limited Warranty 6 666 6 6 00 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Posey Bed 8040 8050 8060 What Does This Warranty Cover Posey warrants to the original purchaser that the Posey Bed 8040 8050 and 8060 are free of defects in materials and workmanship If the product is found to be defective in workmanship or materials we will repair or replace it at our option at no charge other than certain transportation and cleaning charges How Long Does the Warranty Last This warranty is two 2 years from the date of purchase for the canopy frame and one 1 year from the date of purchase for the canopy Useful life of the Posey Bed canopy is estimated at three 3 years but may be extended by proper care maintenance laundering avoiding sharp objects aggressive and destructive patients and avoiding direct exposure to sunlight As of March 1 2014 Posey will no longer repair any canopy that is more than 5 years old as determined by the year and month of manufacture What is Not Covered by this Warranty Damage to the metal frame nylon canopy or other components caused by 1 use in unsuitable environmental conditions or failure to assemble or maintain the product in accord with user and service instructions 2 abuse including but not limited to patient damage misuse alteration exposure to extreme heat or by natural or external forces such as flood or fire
4. C a o a a 26 NOIBS coss saw 0 200 00 c 0 6c 13 v22 REN VN 27 e e 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 6 6 6 6 6 6 6 6 6 6 eee e O 2 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 INTRODUCTION Introduction e 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 gt SAFETY INSTRUCTIONS The Posey Bed Assembly Instructions include important instructions and information related to the assembly of the bed It is important to read the Assembly Instructions carefully prior to assembly of the bed for the first time In order to ensure safe assembly the operator must always comply with the instructions and warnings contained in the Assembly Instructions NOTE The protective devices installed on both the Posey Bed and the accessories may neither be removed nor modified To help reduce the risk of serious injury or death from ENTRAPMENT suffocation or unassisted bed exit read and follow these instructions SAVE THIS MANUAL FOR FUTURE REFERENCE Read the Posey User Manual prior to use Visit www posey com to download a PDF copy Rx ONLY Warnings cautions and notes are provided throughout this manual to indicate levels of SAFETY PRECAUTIONS potential hazards or helpful information as defined below Indicates a safety hazard or unsafe practice which if not avoided could result in serious injury or death Indicates a potential hazard in which failure to follow i
5. Pones 0 7 Base assembly right 1 piece RP8060BAR 8040 8050 8060 Base assembly left 4 piece RP8060BAL 8040 8050 8060 Top amp center pieces and two springs complete without 1 unit RP8040TCP 8040 8050 corner padding Center piece with caster 1 unit RP8060CPC 8050 8060 Center piece with hole 1 unit RP8040CPH 8040 Corner pad green 4 pair RP80400P6 8040 8060 Corner pad light green 1 pair RPBOBOCPLG 8050 Top piece preassembled 1 unit 8011 8060 Slider bar 4 piece RP8060SB 8040 8050 8060 Metal retainer 1 piece RP8060MR 8040 8050 8060 A frame padding green 4 pair RP8060CP 8040 8060 A frame padding light green 1 pair RP8050CP 8050 A frame leg 1 piece RP8060FL 8040 8050 8060 Foam tubing 1 piece RP8060FT 8040 8050 8060 l J K L M Hardware kit 4 kit RP8000HK 8040 8050 8060 J K L M Hardware kit 4 kit RP8060HK 8040 8050 8060 Feet 4 piece RP8040FT 8040 Posey Bed universal strap 1 pair 8018 8040 Caster 1 piece RPSOGOCTR 8050 8060 IV post mounting bracket 1 piece RP8060IV 8050 8060 Complete canopy 8060 green nylon 1 piece 8060T Please call Technical Services for more information at 1 800 44 POSEY 1 800 447 6739 6 090 0 0 09 09 09 0 0 09 0 09 09 0 09 0 09 0 09 09 0 0 0 0 0 0 0 0 0 09 0 6 6 6 6 6 9 24 www posey com 1 800 447 6739 Posey Bed
6. are two ways to install the IV post mount brackets depending on the bed type and the position of the IV post e On top of the IV post page 19 e Below the IV post page 20 6 00 00 00 090 6 09 O 09 09 6 6 6 09 6 6 6 6 6 6 6 6 6 6 6 6 9 6 6 6 6 6 6 6 6 6 6 9 18 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 Installing the IV Post Mount Bracket Part Q from the Top e 6666606 6 09 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 6 gt 1 Position the slider bar Part D above the IV post opening Figs 42 and 43 NOTE The location of the slider bar my be either in front of or behind the IV post depending on the location and design of the head and or footboard Figure 42 shows the slider bar and IV post mount bracket installed in front of the IV post Figure 43 shows the slider bar and IV post mount bracket installed behind the IV post 2 Posey Bed 8040 8050 8060 Attach the IV post mount bracket Part Q to the slider bar Fig 44 Align the IV post mount bracket with the IV post opening Fig 45 and align the wedge of the bracket Fig 46 Repeat Steps two and three on the other side of the IV post Insert the two IV post mount brackets inside the IV post Fig 47 lighten the top Allen head screw using the 3 16 Allen wrench provided Fig 48 The IV post mount bracket must be tightened so it does not move during bed articulation R
7. sale of consumer goods e e e e 6 6 6 0 6 0 6 0 0 6 6 0 6 0 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 www posey com 1 800 447 6739 25 Technical Service from Posey 00 00 90 090 09 09 09 09 0 0 09 0 6 0 We are happy to assist you between the hours of 6 a m and 5 p m Pacific time USA Please call us at 1 800 44 POSEY 1 800 447 6739 or 1 626 443 3143 You can fax us at 1 800 767 3933 Shipping ship items to Posey Company 5635 Peck Road Arcadia CA 91006 0020 USA Canopy Repairs To prevent damage in shipping clean the canopy and close all zippers In Warranty Repairs 1 Forward the product in clean condition with prepaid freight to the above address 2 Clearly mark the shipping container with the RMA number 3 Include dated proof of purchase Out of Warranty Repairs 1 Forward the product in clean condition prepaid freight to the above address 2 We will quote repairs on an item by item basis All quotes include parts and labor 3 lf additional repairs are needed after the initial estimate we will contact you within ten 10 business days of the receipt of the item to obtain approval of any extra charge Repair Turn Around Normally we will ship the product back to you within three weeks from the date of receipt at our warehouse If you return multiple units add one week per unit We will return all units in one shipment unless otherwise agreed Canopies that are
8. the wrong bed may result in serious injury or death to the patient There are a number of hospital beds in use today from many manufacturers that are fully compatible with the Posey Bed canopy Hospital beds come with either removable headboards and footboards or non removable headboards and footboards Compatible hospital beds must meet the following requirements e Length of the bed frame must be lt 96 and does not retract lt 76 e Width of bed frame must be x 36 Height of the bed platform deck of the bed from the floor must be able to adjust between 16 and 25 inches for the 8050 and 8060 models and between 13 and 22 ra inches for the 8040 model 16 25 Depending on the features of the bed operational limits must be also be observed when a Posey Bed canopy is in use as described in the user manual For example the head of bed angle can only be raised lt 70 It is important to Keep the bed platform in the lowest position to keep the canopy tight and avoid material in the patient area when the patient is alone E BEDS WITH REMOVABLE HEADBOARDS AND FOOTBOARDS 13 22 ALWAYS use the IV post mount brackets Part Q on a hospital bed with removable Fig 28A Deck of Bed Dimensions 8040 headboard and footboard Mounting the IV post mount bracket to the IV post socket will firmly attach the A frame to the bed BEDS WITH NON REMOVABLE HEADBOARDS AND FOOTBOARDS ALWAYS use the Posey Bed universal straps Cat
9. 040 8050 8060 www posey com 1 800 447 6739 1 BED ASSEMBLY Mattress Installation continuea 2 Insert the mattress into the mattress compartment Fig 30 3 Completely zip the mattress compartment The mattress must be fully zippered into the mattress compartment at all times when a patient is in the Posey Bed NEVER put a mattress inside the patient area 4 Attach the canopy to the bed frame by securing both bed straps located in the middle of the long sides of rig 30 the bed ACAUTION The canopy bed straps must ALWAYS be connected to a movable part of the bed frame to avoid damaging the mattress compartment 5 Insert the strap through the bed frame Fig 31 6 Bring the strap up through both D rings and then back in between the first and second D ring Figs 32 and 33 7 Pull strap straight down to tighten Fig 34 8 Repeat on the other side of the bed frame ached se 090 0 00 090 0 09 09 0 09 069 09 09 09 09 09 09 09 0 0 09 0 09 09 0 0 0 0 0 09 0 0 6 09 6 6 09 09 6 6 6 6 6 9 9 16 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 BED ASSEMBLY Attaching the Posey Bed to Hospital Beds with Non Removable Headboards Footboards Included with 8040 Models MATERIALS e Assembled bed frame with canopy e Part D e Part O Failure to follow these instructions may result in serious injury or death from a fall or unassisted bed exit ALWAYS use the Posey Bed universal straps C
10. 090 09 0 09 0 09 09 09 0 09 09 09 09 09 0 09 09 6 6 6 6 6 6 O0 6 6 6 6 O For Hospital Bed Selection please see pages 14 15 Bracket Type IV post mount bracket please see pages 21 22 for detailed instructions Hill Rom Centra 850 and 852 Hill Rom Advanta Bed 2000 ACAUTION Remove the footboard raise the knee gatch and attach the IV post inside the footboard not outside Replace the headboard and footboard to engage electronics D 0 0 0 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 oO Posey Bed 8040 8050 8060 www posey com 4 800 447 6739 21 BED ASSEMBLY IV Mounting Bracket Instructions For Stryker Beds The following instructions are for the attachment of the standard IV Post Mount Brackets for the Posey Bed 8050 8060 to Stryker Secure Beds These instructions are for the foot of the bed only To install the IV Post Bracket at the head of the bed follow the standard method of installation Stryker Secure 1 Remove footboard from mounting posts Fig 54 2 Place the IV Post Mount Bracket onto the slider bar with the U shape facing up and the post inward towards the bed Fig 55 3 Insert the IV Post Mount Bracket into the bottom of the footboard mounting posts on the bed Fig 56 57 4 lighten the IV Post Mount Bracket bolt in order to secure the bracket into the mounting post on the bed Fig 58 5 Center the Slider Bar in the IV Post
11. 1 800 447 6739 EERE REE POLAT OEE REIS ENE See page 24 for a complete list of order numbers O for replacement or missing parts Bo l PIERE Opes EAE LAND uem zo 3 f YA _ a oa aa NA Parts Checklist used for 8040 8050 8060 AN ces c Sra ee ITEM E 255 amp pfe e are cats a ELSE rsh spe Ai chia Ae el ale EXEAT Check Part Qty Description L Base assemblies 2 ea Slider bar Metal retainers A frame padding mint green or forest green A frame legs Foam tubing Black connecting pins Nuts 2b c Flat washers Silver star washers Allen head screws Canopy vinyl 8050 nylon 8040 8060 Allen wrench 3 16 O Neu gs O paS O gs pS NE i 6 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 INSTALLATION Unpacking the Parts Continued e 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 06 6 06 Parts Checklist used on 8040 8050 8060 Cont Parts Checklist used on 8050 and 8060 Q Check Part Qty Description Se Go C yo Bottom center piece with caster C2 Casters f f T 1 0 IV post mounting brackets Check Part Qty Description Top center piece w two springs Top pieces w two corner pads Check Part Qty Description Universal bed strap Feet Bottom center piece with preassembled foot Check Part Qty Description po fof pup Deu mH a xxx MD f Ris
12. 8018 for a hospital bed with a non removable headboard and footboard to firmly attach the frame to the bed NEVER activate any of the features listed below while using the Posey Bed canopy NEVER lower the deck of the bed below sixteen inches 16 8050 and 8060 models or below thirteen inches 13 8040 model from the floor to prevent suspending the mattress above the bed deck The bottom of the canopy must be fully a H supported by the bed deck to prevent canopy damage 8050 8060 NEVER raise the hospital bed above twenty five inches 25 8050 and 8060 models or above twenty two inches 22 8040 model from the floor to the deck of the bed NEVER tilt the hospital bed surface head to foot or foot to head Trendelenburg feature NEVER allow the hospital bed to transform into a chair shaped position where the foot of the bed can be lowered to an angle greater than five degrees 5 Deck of bed 13 or 14 Using these features will damage the canopy system and bed motors and will increase the risk of serious injury or death from ENTRAPMENT suffocation from excess material in the patient compartment or from an unassisted bed exit which could result in a fall Deck of bed 16 or 17 8040 6 6 00 090 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 06 14 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 BED ASSEMBLY Incompatible Beds 6 0 0900 090 090 09 09 09 0
13. Mount Bracket and tighten the retaining bolt Fig 59 6 Replace the footboard onto its mounting posts on the bed Fig 60 ACAUTION Be sure to inspect that the footboard and the legs of the canopy frame do not touch or come into contact while raising or lowering the bed Figs 61 62 Fig 62 22 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 Assembly Check 1 The bed assembly is completed Fig 63 Check e Bed frame feels secure with no loose or moving parts e No foam is visible All zipper pins are completely seated in the pin box and all zipper teeth are engaged No rips or holes appear in the canopy or netting Zippers open easily and close securely with no holes or gaps along the entire length of the zipper No hardware is left over otore all Posey Bed instructional material in the instruction storage pocket located on the side of the bed Fig 63 The Posey Bed is now ready for delivery or storage NOTE Ihe Posey Bed is designed for use in normal indoor environments The Posey Bed may be stored in ambient warehouse temperatures at normal humidity levels Avoid excess moisture or high humidity that may damage product materials 6 6 6 6 6 6 6 09 6 09 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 oO Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 23 Replacement Part Availability PartNo Description Qty Cat No
14. Posey Bed 8040 8050 8060 Assembly Instructions 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 06 U S Patent No 7 047 991 amp 7 383 849 Rx ONLY Table of Contents 6 6 6 09 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 INMOGUCHON a anana sg a a aha AA MANG RENA ead ees terre A AA AK AA ers eee A AA Ta AE AENG eens 3 specifications for the Posey Bed O QC RRRRRRRRRRRRRRRRRRRRR RR RR Rh 4 DI ID e ne 20020200220 aco tin dh ae TTL TTE 4 SEa DO 2 00660012202010 2 90 0 00006 TEMERE SR 202 c 02022202 D ht ru MeTHPCPT nr 5 BIIBSE IDEE PAS react mace eva er ka Ta Tk a Sana Ki a Dae au dee a iur ead aod efus Ee ded a ake a uid pa dorada s dd 6 CE Ins FOTO EIODILa c in pacar Seg ay grec iei eit Ar i git Daa Sind udi qii 0 9 8050 and 8060 Models Caster lnstallation 8 0040 Modol tee IMS UAIAUOM 5 as o a ees one d adt oo Ob dee E695000 RONNE ATONE RATES BG BB NR nes ga Ni 9 A Frame Assembly 8040 8050 and 8060 Models 10 VOD Piece ISO LIDDI su ng c g 9 a D onte tur ip 4 138 onde E ardt torte reto tage Y uiv tor E t Pede Y ad 11 12 C08 O T 11 G010 100 NIBUS qoe RU RR ERE RE v0 00 xi0 00010 EIC C HI 000 PERPE 210002905100 CIC D 12 Canopy Install
15. at 8018 to firmly attach the Posey Bed frame to hospital beds with non removable headboards and footboards NEVER use the universal straps on beds with removable headboards and footboards Doing so will cause the A frame to detach from the hospital bed when the bed is raised ALWAYS properly secure the Posey Bed universal straps ALWAYS use Posey Bed headboard footboard pads Cat 8002 to cover the headboards and footboards to help prevent injury from direct contact with the solid structure 1 Position the A frame around the hospital bed and adjust the length of the top piece and base piece of the frame to fit around the frame of the bed 2 Wrap the large horizontal strap A horizontally around the headboard or footboard 3 onap the quick release buckle closed Fig 35 4 Adjust the strap so that it fits snugly around the head or footboard Fig 36 NOTE he large buckle from strap A should be facing in toward the bed 5 Adjust the position of strap A so the three slider bar support straps are between the two vertical frame bars Fig 3 6 Raise the slider bar Part D from the frame even with the three slider bar support straps B Fig 38 7 Using the tab provided separate the hook and loop from each strap and place the slider bar in the lt center of each strap Fig 39 Tighten each strap Fig 39 8 Wrap each of the small Vertical Straps C vertically around the head or footboards 9 Snap the quick release buck
16. ation 8040 8050 8060 Models 13 Choosing the Right Bed for Use with the Posey Bed 8040 8050 or 8060 14 15 Ji RITU 5 geek 0 11 AN a EE NG BENG NA E ee eee ee eee 15 Vidit d Iris sna cy exegesis arg 60 gag Ka Ba C020 c6 ae ae aT ora a ge oa 15 Attaching the Posey Bed to Hospital Beds 17 22 with Non Removable Headboards Footboards 8040 Models 17 with Removable Headboards Footboards 8050 and 8060 Models 18 Installing the IV Post Mount Bracket Part Q 0 mmm mmm mm mm m m mme 19 22 from the 0p RR RR RR RR Ru Ra Rh ra rr kg ta 19 ONE 001 00000 n EA ca cee GR E BB ween aes 20 Bed To Bracket Cross Reference 6 aa da anos deatur uar ie ai ew a dica ng wa d ng S HE RHEE UU Oden eens 394008 42 0 004 d 21 IV Mounting Bracket Instructions For Stryker Be s 22 ASSCMMNY Gees s iua reese ee AE ERREA RS CAE 9 ORG AEEA EO E E 23 Replacement Part AvailabilifV c On neo 24 Posey Limited GITdI fica240112 2 1226222621222 600620 5660 0266L6 20666006 E012xi000 60022s0000x 20001516 C 25 Technical Service from POSEy sasana de anana QC EQ RC QC Ede EE CREDE C COE e oe a CC e 3
17. e Damage caused by alteration modification or repair unless performed by Posey e Consequential or incidental damage including but not limited to loss of income or profits is not covered The laws of some countries may not allow exclusion of such damages so this limitation may not apply to you Cleaning and Shipping Charges e Shipping costs for products sent to Posey must be pre paid by you Posey will pay return shipping costs for repaired or replaced products via Ground service unless otherwise agreed How to Get Service Contact the Posey Technical Service hotline 1 800 447 6739 to report the problem and get a Return Merchandise Authorization RMA Carefully pack and ship the returned product to us with your RMA to Posey Company 5635 Peck Road Arcadia CA 91006 0020 e n clean condition Canopies that are returned soiled or with an odor will be returned immediately and will not be inspected or repaired e With proof of purchase and e Freight prepaid by you Posey will inspect the product and contact you within ten 10 business days of the receipt of the item to explain the results of our inspection and what is or is not covered How Does State Law Apply This warranty is governed by the laws of the State of California USA It gives you specific legal rights You may have other rights which vary from state to state This warranty does not affect any further rights that you have under the laws in your state for
18. enter piece must be able to slide freely so that the frame can move as the bed articulates Figs 18 and 19 ACAUTION The bed may not always fit through some doorways In this situation lower the top piece to the lowest position pushing the silver metal detent pin into the bottom hole Fig 16 and then return it back to the top hole after transport ACAUTION The Allen head screws on the top center piece of the Posey Bed must be secure but loose enough so the A frame slides freely when raising or lowering the head or foot of the hospital bed A failure to heed this warning may interfere with proper operation of the hospital bed see red arrows Fig 18 6 0 00 00 0900 909 6 9 6 6 09 ee e Corner Pads Top Hole Bottom Hole Fig 16 Corner Pads Top Hole Bottom Hole Fig 17 Fig 18 12 www posey com 1 800 447 7 6739 Posey Bed 8040 8050 8060 INSTALLATION Canopy Installation 8040 8050 8060 NEN 090 0 090 00 09 0 09 0 09 09 09 09 09 06 6 6 09 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 MATERIALS e Part H e Part F e Part R e Assembled bed frame 1 Attach the foam padding Part H and the A frame padding Part F to the bed frame Figs 20 and 21 2 Make sure the seams of the top foam pads are oriented so the Allen head screws have space to move Fig 22 3 Unfold the canopy Part R on the bed t ACAUTION ALWAYS orient the canopy so the l
19. epeat on the other side lighten the side Allen head screw Part M Fig 49 Repeat this step on the other side 10 Repeat steps one through ten on the other end of the bed Fig 42 Fig 43 Fig 44 Fig 45 Fig 46 Fig 47 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 www posey com 1 800 447 6739 19 In stalling the IV Post Mount Bracket Part Q from Below the IV Post opening Attach the IV post mount bracket to the slider bar by aligning the IV post mount bracket with the post opening Fig 50 Align the wedge of the bracket Fig 51 Repeat steps 2 and 3 on the other side of the IV post Insert the two IV post mount brackets inside the IV post Fig 52 lighten the top Allen head screw using the 3 16 Allen wrench provided Fig 53 The IV post mount bracket must be tightened so it does not move during bed articulation Repeat on the other side lighten the side Allen head screw Part M Repeat this step on the other side e 090 6 6 6 0 6 6 6 O 6 6 6 6 6 6 6 6 6 6 9 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 6 Position the slider bar Part D below the IV post se 0 00 090 090 090 09 09 09 0 09 09 09 09 09 0 09 09 0 09 0 0 0 9 09 0 09 6 090 6 6 6 6 6 Posey Bed 8040 8050 8060 BED ASSEMBLY Bed To Bracket Cross Hererence 6 00 090 00 0900 0900 09
20. he bed NOTE For one person set up use your foot to lift the slider bar Part D before placing the assembled A frame legs into the retainers of the base assembly Fig 11 8 Secure the A frame legs to the base assembly using black connecting pins Part I Figs 12 and 13 9 Repeat steps and 8 for the other assembled A frame legs on the opposite side 10 Re install the four Allen head screws from steps 5 and 6 on all four A frames legs and tighten Fig 9 Fig 10 Fig 11 Fg 12 Fig 13 se 090 0 00 090 0 09 09 0 09 06e 09 09 0 09 09 09 069 0 09 0 0 09 0 0 0 0 0 0 6 0 0 6 09 6 6 6 6 6 6 6 6 6 69 9 9 6 9 1O www posey com 800 447 6739 Posey Bed 8040 8050 8060 INSTALLATION Top Piece Installation 8060 Model 6 606 6 6 0 6 09 6 O 09 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 9 9 9 MATERIALS e Part C1 Corner Pads NOTE Leave pre installed corner pads in place 1 Place the top piece Part C1 section into the metal retainers on the head of the A frame legs Fig 14 i NOTE For one person set up insert the top piece one end ne Top Hole at a time 2 Push the silver metal detent pin into the top hole Fig 15 NOTE Make sure the silver metal detent pin protrudes out through the hole on the metal retainer 3 Repeat step 2 for the other side of the assembled A frame legs NOTE The top center piece must be able to slide freely
21. i hi F Storage W Instruction Storage Pocket is positioned on the open side T oe of the frame Fig 23 4 Unzip the top rail zipper of the canopy look for the large Posey logo Fig 23 5 Wrap the top of the canopy over the padded frame 6 Fasten the support straps on each side of the top rail of the canopy before zipping Fig 24 7 Insert the zipper pins properly into the zipper box and zip closed using the zipper pull tab Figs 25 and 26 When zipping the canopy make sure the zipper pins are completely seated Failure to do this will prevent the zipper from closing securely which may lead to unassisted bed exit and potential patient injury ACAUTION To avoid damage to zippers and fabric be sure to pull the fabric closed as each panel is fully zipped 8 Unzip the zippers on the side pieces 9 Wrap the canopy side piece around the padded frame legs and close the zippers Fig 27 10 Repeat on all four sides Fig 22 Fig 23 Fig 25 Fig 26 Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 13 BED ASSEMBLY Choosing the Right Bed for Use with the Posey Bed 8040 8050 or 8060 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 96 6 e e 4 The Posey Bed is an A frame canopy that attaches to a compatible hospital bed Because the canopy does not include a bed it is very important to select the correct hospital bed for proper and safe use Using
22. in neha LU it AR Rc rias SIT SAIS ANILLO Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 7 INSTALLATION Caster Installation 8050 and 8060 OGE e e e e e e e e e e 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6e 6e 6e 909 MATERIALS e Part A 2 e Part B2 e Part J Part K Part L Part M Part P 9 16 wrench mb Unfold each base assembly Part A until corners are at 90 degrees Fig 1 Place a flat washer Part K over the caster post Part P Insert the caster Part P into the pre drilled hole next to the corner receptacle in the base assembly Part A Place a star washer Part L and nut Part J on the caster bolt Fig 2 Use the 9 16 wrench not provided to tighten 5 Repeat steps 2 through 4 on the remaining three corners 6 Remove the Allen head screw Part M from the arm of each base assembly Part A and keep for use at a later step 7 With slots facing inside Fig 3 slide the bottom center piece Part B2 over both base assembly arms 8 Reattach the Allen head screw in the slots of the bottom center piece Part B2 Fig 4 MAACAUTION The Allen head screws on the bottom center piece of the Posey Bed must be secure but loose enough so the A frame slides freely when raising or lowering the head or foot of the hospital bed A failure to heed this warning may interfere with pro
23. les closed Fig 40 10 Adjust the straps so they are snug Fig 41 11 Repeat at the other end of the bed d n e se 0 6 0 0 0 O0 6 6 6 6 6 6 6 6 6 6 6 6 06 6 6 06 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 oO Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 17 Attaching the Posey Bed to Hospital Beds with Removable Headboards Footboards Included with 8050 and 8060 Models eeeeeees5eeeeesecs3ueaeeoeee5eoseeoeeee25eeeee eees eeee eet 6 6 6 6 6 6 gt MATERIALS Assembled Bed Frame with Canopy e Part D e Part M e Part Q Failure to follow these instructions may result in serious injury or death from a fall or unassisted bed exit ALWAYS use the Posey Bed IV post mount brackets Part Q to firmly attach the Posey Bed frame to hospital beds with removable head and footboards ALWAYS properly secure the Posey Bed IV post mount brackets Failure to attach the canopy to the bed frame properly will cause the A frame to detach from the hospital bed 1 Position the A frame around the hospital bed and adjust the length of the top piece and base piece of the frame to fit around the frame of the bed 2 Adjust the bed with the hospital bed control so the bed is approximately mid level 3 Turn the bed electronics OFF 4 Remove the headboard and the footboard from the hospital bed 5 Prepare to attach the IV post mount bracket Part Q to the frame of the bed There
24. me with canopy Choosing The Right Mattress For Use With The Posey Bed The Posey Bed 8060 mattress compartment is designed to fit either e A standard mattress 6 x 35 x 80 15 cm x 89 cm x 203 cm e An inflatable air type mattress 10 x 35 x 80 25 cm x 89 cm x 203 cm The Posey Bed 8040 and 8050 mattress compartments are designed to fit a standard mattress 6 x 35 x 80 15 cm x 89 cm x 203 cm NEVER use a mattress of a different size than the compartment is designed to fit Using a smaller mattress will result in gaps between the canopy and mattress Using a larger mattress will stress the fabric and may damage the zipper 1 Completely unzip the mattress compartment NOTE 8060 only In order to fit the ten inch 10 25 cm air type mattress the Posey Bed 8060 mattress compartment must be fully expanded a Locate the expansion zipper behind the instructions storage pouch on the side panel Fig 29 b Unzip the mattress compartment using the red zippers around the entire bed e Make sure the expansion zipper 8060 only is closed when using a six inch 6 15 cm mattress e NEVER open or close the mattress compartment while the head or knee of the bed is in the up position as this may damage the fabric and or zippers Fig 29 8060 Mattress Compartment Location 6 6 0 6 6 6 6 6 6 09 6 09 6 0 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 oO Posey Bed 8
25. nstructions may result in minor or moderate injury to the patient or caregiver or damage to the Posey Bed NOTE Indicates a reminder or other helpful information to make bed assembly easier and more efficient NEED HELP Please call Posey Customer Support at 1 800 447 6739 between 6 00 a m and 5 00 p m Pacific time if additional help is required You can also contact an authorized Posey Bed dealer 6 6 6 6 6 6 6 6 6 6 6 6 6 6 00 00 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 oO Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 3 INTRODUCTION Specifications for the Posey Bed e 666 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 OPERATING CONDITIONS The Posey Bed is designed for use in normal indoor environments STORAGE CONDITIONS The Posey Bed may be stored in ambient warehouse temperatures at normal humidity levels Avoid excess moisture or high humidity that may damage product materials Dimensions 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Top Piece Preassembled C1 8060 Metal Retainer E Top Piece w Springs B1 8040 and 8050 f7 or 196 cm 8040 w installed feet 79 or 200 cm 8050 8060 w installed casters Base Assembly A Bottom Center Piece B2 with caster 8050 8060 4 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 General Information
26. per operation of the hospital bed see red arrows Fig 4 Fig 1 w N Geral Er GET B gt Completed Frame Assembly 6 00 00 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 6 O6 8 www posey com 800 44 6739 Posey Bed 8040 8050 8060 INSTALLATION Feet Installation 8040 Model e 090 6 6 6 09 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 9 9 MATERIALS e Part A 2 e Part B2 e Part J e Part K e Part L e Part M e Part N i e 9 16 Wrench 4 90 Degrees 1 Unfold each base assembly Part A until corners are Flat Washer Part K at 90 degrees Fig 5 2 Place a flat washer Part K over the foot post Part N Fig 9 Fig 5 3 Insert the feet Part N into the pre drilled hole next to the corner receptacle in the base assembly Part A 4 Place a star washer Part L and nut Part J on the feet bolt Fig 6 Use the 9 16 wrench not provided to tighten Feet should now be properly installed Fig 7 5 Repeat steps 2 through 4 on the remaining three corners 6 Remove the Allen head screw Part M from the arm Nut Part J of each base assembly Part A and keep for use at a pt later step e Star washer Part L 7 With slots facing inside slide the bottom center piece Part B2 over both base assembly arms 8 heattach the Allen head screw in the slots of the bottom center
27. piece Part B2 See Fig 8 A CAUTION The Allen head screws on the bottom center piece of the Posey Bed must be secure but loose enough so the A frame slides freely when raising or lowering the head or foot of the hospital bed A failure to heed this warning may interfere with proper operation of the hospital bed see red arrows Fig 8 0 91 Completed Frame Assembly 4 d e 0 6 0 6 0 O0 6 6 6 6 6 6 6 6 6 6 6 6 606 6 6 06 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 oO Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 9 INSTALLATION A Frame Assembly 8040 8050 and ANAA MOARE 0 0909 0900 090 0900 09 0 09 09 09 6 09 6 09 09 6 09 09 09 09 6 6 09 6 6 06 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 6 MATERIALS e Part D e Part E e Part G e Part 1 Insert the two A Frame Legs Part G into the metal retainer Part E Fig 9 2 Use the black connecting pins Part to secure the two A frame legs Part G with the metal retainer Part E Fig 10 3 Insert the slider bar Part D into the assembled A frame legs 4 Repeat steps 1 through 3 for the other side 5 Remove the Allen head screw from the vertical corner of the base assembly arm and keep for use at a later step Fig 11 6 hepeat step 5 on the remaining three corners T Slide the assembled A frame legs Part G into each retainer with the flat face of the metal retainer Part E facing inside t
28. returned soiled or with an odor will be returned immediately and will not be inspected or repaired 0 6 6 6 6 6 6 6 6 6 6 6 6 6 06 6 06 06 0 www posey com 1 800 447 6739 Posey Bed 8040 8050 8060 6 666 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 9 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 eee 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 2 Posey Bed 8040 8050 8060 Assembly Instructions Posey Posey Company 5635 Peck Road Arcadia CA 91006 0020 USA Phone 1 800 447 6739 s Fax 1 800 767 3933 www posey com 2015 Posey Company All rights reserved M5080 REV D 020515
29. so Fig 14 that the frame can move as the bed articulates ACAUTION The bed may not always fit through some doorways In this situation lower the top piece to the lowest position pushing the silver metal detent pin into the bottom hole Fig 14 and then return it back to the top hole after transport Bottom Hole Corner Pads Top Hole Bottom Hole 4 d e 0 6 0 0 0 06 6 6 6 6 6 6 6 6 O 6 6 6 606 6 6 06 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Posey Bed 8040 8050 8060 www posey com 1 800 447 6739 11 INSTALLATION Top Piece Installation 8040 and 8050 MOGE MATERIALS e Part C NOTE Leave pre installed corner pads in place 1 Remove the two Allen head screws from the top piece Part C and keep for use at a later step 2 Place each top piece section into the metal retainers on the head of the A frame legs Fig 16 NOTE For one person set up insert the top piece one end at a time 3 Push the silver metal detent pin into the top hole Fig 17 NOTE Make sure the silver metal detent pin protrudes out through the hole on the metal retainer 4 Repeat steps 1 through 3 for the other side of the assembled A frame Legs 5 Slide the top center piece Part B1 with the provided springs over each top piece and then re install DO NOT tighten the Allen head screws from step 1 Slots should be oriented on the same side as the top piece holes NOTE The top c
Download Pdf Manuals
Related Search