XC800 Family Guide to using the DALI LightNet tool
Contents
1. Scene 10 255 Scene 11 255 Scene 12 255 scone i3 E5 Phy MinLevel 10 Maximum Level 250 Minimum Laval IU Power ON Level 220 Sys Fail Level 250 Versioning Level Remove r Program Short Add lo Program Fade Control Ee Rate 1 r Power Control Settings Scene 6 255 Scene 14 255 Scene 7 255 Scene 15 255 Version Number f Type DTA Max Lev gt ll Level hon i Device Enable Type Reset BENE Il ll Ii me 2 E I ll d address of last accessbile memon location T checksum of memory bank 1 neiz Wolastaec mem bank memory bank Hock byte nas TINEweO MSE OEMGTIN byte 0 MEE 0 04 eee ERE i5 BTNbge2 JOEMGTINb TE ET BTNbget OEMGTNbytes GTIN bate 5 CEM GTIN byte 5 ctrl gear firmware ver major CEM serial amp byt m ctrl geas eas wer minor CEM serial t NE DEM serial B byte 3 OWOC sevisirumberbyte2 EMM serial W byte 4 LSE MD serisinumberbyte Subsystem 4 7 Device 0 3 E tarred Lamp type lock able MF add at gear information Lamp type Figure 12 Screenshots of LightNet tool Application Note 12 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Getting started 2 3 DALI Control Device Software The DALI Software for Control Device has been developed to support the use of the LightNet tool and can work2. 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Getting started POWER SUPPLY UNIT 15V GND DALI BUS POWER SUPPLY UNIT 5 DALI BUS are DALI Control DALI Control Device Device PC Connection via USB UART a T A 15 supply with 1000 resistors Control using 2o Sh f to power up the DALI bus line LightNET Software ee b d e 7 P af AL J DALI Power Supply d ES DALI Master Board E x DALI Slave Board Control Device LUN Control Gear P m Comprising of KIT XC836 EK V1 KIT XC822 XCB836 DAL AA Comprising of KIT DALI RGB XC836 DKV1 Figure 20 DALI Network Hardware connection Application Note 18 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 LightNet Tool 3 LightNet Tool This chapter describes how the LightNet software is organised 3 1 Connecting the LightNet tool Once the recommended hardware setup has been completed LightNet can be used Figure 21 shows how to connect to the LightNet tool Note The LightNet tool cannot be activated if the recommended setup has not been completed as described i e the XC836 Easy Kit is not connected or the BMI is incorrectly selected Board Connection inn RED indicates that Board Connection GREEN indicates that board is not connected board is connected Clicking on Con
3. Addr Status YES or NO Device Stalus Indicates if device has short address missing Lamp Arc Power Control Gear OK Status YES or NO Indicates power status Status ON or OFF Lamp Failure IND Lamp Arc Power Power Failure Indicates if power failure has Limit Error Limit Error NO occurred If no failure it Indicates if last requested means that a RESET or an arc power level is between i 2 TA arc power control command MIN and MAX LEVEL or Actual Level Fade Tim has been received since last OFF i 7 power on Status is YES or NO e EE CER Status is YES or NO Actual Levet Indicates current power level of connect device Device Type Indicates which device is Fade Time connected Fade Rate Range 0 to 15 0 Fluorescent lamps 6 LED modules Figure 24 Device Status Application Note 20 V1 4 2012 10 Guide to using the DALI LightNet tool AP08104 Infineon LightNet Tool Go To Scenes Scenes Supports 16 scenes User to select desired scene to enter Scene ll Scene 2 Scene 1 Scene 8 Scene 2 Scene 10 Scene 7 Scene 11 Scene 4 Scene 12 Scene D Scene 13 scene b Scene 14 Se BL J Scene 7 Scene 15 Go to Scene Go To Scene Click button to jump to the selected Scene Figure 25 Goto scenes 3 4 Detailed Configuration Command Tab This section describes the options in the configuration settings Group Selects group for selected device to join or remove S
4. Circuit Item Reference Value Device Package Description 1 MB2S MB2S SOIC 4 Bridge Rectifier 2 1u 25V C EUC1210 C1210 Capacitor 3 BAS16 DIODE SOD323 R SOD323 R Diode 4 BZX384 2V7 DIODE SOD323 R SOD323 R Diode 5 IC1 SFH6156 2 SFH6156 SFH 5 3 kV TRIOS High Reliability Optocoupler 6 IC2 SFH6156 2 SFH6156 SFH 5 3 kV TRIOS High Reliability Optocouplerstor 7 BC817 25W BC817 SOT323 NPN Transistor 25WSMD323 8 10R R EU R0603 R0603 Resistor 9 OR R EU R0603 R0603 Resistor 10 R3 OR R EU R0603 R0603 Resistor 11 R4 11k R EU R0603 R0603 Resistor 12 R5 324R R EU R0603 R0603 Resistor 13 R6 4R7 R EU R0603 R0603 Resistor 14 R7 1k21 R EU R0603 R0603 Resistor 15 R8 3k16 R EU R0603 R0603 Resistor 16 X1A MKDSN1 5 2 MKDSN1 5 2 5 08 MKDSN1 5 MKDSN 1 5 2 5 08 Printklemme 5 08 2 5 08 17 X1B 2x1 PINHD 1X2 1X02 Pin Header 18 x2 4x1 PINHD 1X4 1X04 Pin Header Application Note 26 V1 4 2012 10 Cinfineon Guide to using the DALI LightNet tool Table 1 Bill of Material for DALI PHY Circuit item Value 19 H1 SAMTEC SSQ 1 14 03 S S 20 H2 SAMTEC SSQ 1 14 03 S S Application Note AP08104 References Device Package Description PINHD 1X14 1X14 Pin Header PINHD 1X14 1X14 Pin Header V1 4 2012 10 Infineon Guide to using the DALI LightNet tool AP08104 APPENDIX DALI Control Gear Board Schematic for KIT DALI RGB XC836 DKV1 References
5. DMX512 PHY 225 7 03 8403 J1 1 J1 2 21 3 2205 7 033 03 J2 1 J2 2 22 3 Note 1 Short JP to enable termination resistance 2 This circuit does not use isolated 3 Supported DMX address range gt from 1 18 ay Developer must follow the isolated topology specified in the standard C2 XXDnF DALI PHY L MKDSNT 512 5 08 MKDSN1 5 2 5 08 vec Wil l x 0 o R3 OR p x120 Fak BALL RX 2 N 20k SFHOISA 3 E OR WEC ONDO l Ig 4 nae Ax RS i E DALI TX e SER Sa SFHETBA 3 l C1 22uF 50V MENU Figure 32 Control Gear Board Schematics Part 1 Application Note 28 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 References SS XC836 Power LED Ci vcc 5 E P1B DESTI RY P n 9 Eo P 1 Ag z f Ca S 02 E25 E Br 33uF 6 3V a t GND LED1 DIE 3 EM COUTED DIP2 S m CCGBD DIF i SCOUTS DIPO coal BLUE CH FU P B COUTA DMX512 DIS RX CCA a a m a m DALI TX L 0 COUTES DALI RX EE OE M vec 25 Fi C4 18 MTALS 100nF GND GND E a goes Pin gw Conn E VCC VEC 2 05 7028 02 X22 Xii SPD i cal C5 2223 2031 TELA EIS av GND LJ L mw CT DNA 885 111 ES XTAL CDNA GND L IC4 BCR421 GND H L L Fi
6. Infineon AP08104 Getting started 2 Getting started This section is a guide to installing LightNet 2 1 AP08104 Software Package This software package consists of the installation package for the LightNet software running on the computer and a DALI Software for Control Device developed to support the use of the LightNet tool The following figures step through the software installation on the user s computer i Copy ap0810413_LightNet ap0810413 LightNet You are about to copy ap810413 LightMet package files on your computer Click Mext to continue Figure3 Copying ap08104 i Copy ap0810413_LightNet Select Destination Location Where should ap0810413 LightMet be stored A Software will store ap0810413 LightNet into the following folder To continue click Next T you would like to select a different folder click Browse At least 0 9 MB of free disk space is required Figure4 Selecting destination location Application Note T V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Getting started i9 Copy ap0810413 LightNet Ready to Copy Software is now ready to begin copying ap810413 LightMet on your computer Click Copy to continue with the copying process or click Back if you want to review or change any settings Destination location C ap0810413 LightNet Figure5 Start the copy process p Copy ap
7. fade time rate Fade Time Range 0 to 15 Fade Rate Range 1 to 15 Steps to select Fade Control Settings 1 Select from drop down list Once setting new setting takes effect Power Control Settings Sets the desired power setting for selected device Supports following setting Maximum level Minimum level System Failure level Power ON level Steps to Set power settings 1 Select the type of power setting to be changed 2 Enter the desired level in the Level field 3 Click on the Set to activate setting 4 The new settings will only be programmed to the flash upon OFF selection in the Lights Control tab V1 4 2012 10 Infineon Guide to using the DALI LightNet tool AP08104 Refresh Click on this to refresh data in window General Control amp Status Detailed Configuration Scenes Indicates the power level information from Scene 0 Sne to 15 Scene EN Scene B 255 Scene 255 Scene 8 255 ewe EE Scene 10 255 Scene 3 255 Scene 11 255 Scene 4 255 Scene 12 255 Scene 5 255 Scene 13 255 Scene b 29 Scene 14 255 Group Scene 7 255 Scene 15 255 Indicates the group s that ES selected device belongs Group Power Levels Status Phy Min Level 12 Maximum Level 160 Minimum Level i 2 Pawer ON Level 30 Sus Fail Level 160 Versioning Version Number to 0 1 AB Figure 27 Device Information Application Note 22 LightNet Tool Physical
8. for Infineon Control Device and Control Gear 2 5 1 Setting up the Control Device for LightNet The XC836 Easy Kit board can be used as the LightNet DALI Control Device with the following steps 1 Connect and download the generated hexfile File Lightnet XC800Master hex from Section 2 3 into the XC836 Easy Kit board using XC800 FLOAD in DAVEBENCH or KEIL UVision4 Application Note 13 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Getting started Note To ensure the success of the following procedures please ensure that the device is configured to User Mode Diagnostic and COM_SEL settings is set to USB This is a default setting Control modes supported where VDDP is supplied LightNET via PC by 5Vdc from USB port Touch Pad control COM SEL Ej er Marx j M me Touch pads for Connect to PC for da Fs F command selection LightNET control 2 3 7 CUN io NL uu Displays the command selected Displays connected devices PC control Displays 8888 ALL Broadcast command Touch Pad Control Displays commands D1 Short Address 0 D2 Short Address 1 D3 Short Address 2 Figure 14 Overview for DALI Master Control Device Connections for the DALI PHY Board DALI PHY x1 DALI BUS DALI PHY KIT XC822 XC836 DALI Connect
9. to DALI Bus DALI PHY is attached onto H2 and H1 headers on the XC836 Easy Kit Figure 15 DALI PHY connection for XC836 Easy Kit Application Note 14 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Getting started METHOD 1 PC Control via LightNet H H IS 8 The LED display shows 8888 whenever LightNet is used LightNet functions are described in this document METHOD 2 TOUCH PAD Control lt Upon powering up default control mode using touch pad control is entered sends Broadcast Address Increase brightness Goto Scene 0 Sends Short Address Decrease brigntness 6 7 Turns on connected device 9 DEVICE 2 SCENE2 sends Short Address 2 Turn off connected device H I a od j DEVICE 3 SCENE3 Figure 16 DALI Control using PC and Touch Pad description 2 The DALI Control Device is now ready to be connected to the DALI bus 3 User can control the DALI network using LightNet via PC and through the Touch Pad available on the XC836 Easy Kit 2 5 2 Setting up the Control Gear The DALI Control Gear can be setup with the following steps 1 Connect the DAP MiniWiggler to the DALI Control Gear as shown in Figure 17 Download the hexfile File AP08102 v1 2 Slave hex from Section 2 4 into the DALI Slave Board using XC800 FLOAD in DAVEBENCH or KEIL UVision4 2 The DALI Control Gear is now ready to be connected to the DALI bus Application Note 15 V1 4 2012 10
10. 0810413 LightNet Completing the ap0810413 LightNet Wizard Software has finished copying ap0810413 LightMet on your computer Click Finish ta exit Software Figure 6 Copy completed 2 2 LightNet Installation The LightNet software is designed to provide the control device the facility to send basic DALI commands to the connected control gear Installation is only to be performed once using the file LightNet setup V1 3 exe The following figures step through the LightNet tool installation process Application Note 8 V1 4 2012 10 Infineon Guide to using the DALI LightNet tool AP08104 is Setup LightNet Welcome to the LightNet Setup Wizard This will install LightMet V1 3 on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to eat Setup Figure7 LightNet tool installation window Application Note Getting started V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Figure 8 Figure 9 Getting started Setup LightNet License Agreement Please read the following important information before continuing Please read the following License Agreement You must accept the terms of this agreement before continuing with the ingtallation IMPORTANT NOTICE AND TERMS OF USE Please read the following important notice as well as the following terms and conditions carefully The installatio
11. Cinfineor TP ed Ak aiaa Qeon gare neos XC800 Family Guide to using the DALI LightNet tool AP08104 Application Note V1 4 2012 10 Microcontrollers Edition 2012 10 Published by Infineon Technologies AG 81726 Munich Germany 2012 Infineon Technologies AG All Rights Reserved LEGAL DISCLAIMER THE INFORMATION GIVEN IN THIS APPLICATION NOTE IS GIVEN AS A HINT FOR THE IMPLEMENTATION OF THE INFINEON TECHNOLOGIES COMPONENT ONLY AND SHALL NOT BE REGARDED AS ANY DESCRIPTION OR WARRANTY OF A CERTAIN FUNCTIONALITY CONDITION OR QUALITY OF THE INFINEON TECHNOLOGIES COMPONENT THE RECIPIENT OF THIS APPLICATION NOTE MUST VERIFY ANY FUNCTION DESCRIBED HEREIN IN THE REAL APPLICATION INFINEON TECHNOLOGIES HEREBY DISCLAIMS ANY AND ALL WARRANTIES AND LIABILITIES OF ANY KIND INCLUDING WITHOUT LIMITATION WARRANTIES OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY WITH RESPECT TO ANY AND ALL INFORMATION GIVEN IN THIS APPLICATION NOTE Information For further information on technology delivery terms and conditions and prices please contact the nearest Infineon Technologies Office www infineon com Warnings Due to technical requirements components may contain dangerous substances For information on the types in question please contact the nearest Infineon Technologies Office Infineon Technologies components may be used in life support devices or systems only with the express written approval of Infin
12. HID etc to become IEC 62386 The complete standard for control interface of electronic control gears was published in June 2009 while the standard for lighting control devices is scheduled to be published in 2012 Only a pair of wires are required to form the bus for communication to all devices on a single DALI network Each piece of operating equiment with a DALI interface can be communicated with individually Using a bi directional data exchange a DALI controller can query and set the status of each connected lighting device As a standalone system DALI can be operated with a maximum of 64 devices Alternatively DALI can be used as a subsystem via DALI gateways for connection to building management systems Grouped System Brightness control within large open plan office lecture halls or conference rooms DALI can provide zoned or localised control of lighting Control could be offered through infra red remote control or a software control with GUI support or used together as an easy configuration tool to group loads together Offering flexibility in customised lighting DALI Control Device s e g Control Panel Remote Controller software control with GUI support DALI Bus Complex System Multiple DALI systems can be connected together utilising gateways to building management systems Software programs offer more sophisticated programming functionality for grouped systems such as scenesetting timeclock a
13. Infineon Guide to using the DALI LightNet tool AP08104 Power Conn Connector X3 Programming Pin Connector X2 Getting started Connections for programming the DALI oV Supply Control Gear using a DAP MINIWIGGLER 23 2 X3 VCC GND VCC GND KIT DALI RGB XC836 DKV1 KIT DAP MINIWIGGLER USB DAP miniwiget E LH Ed 73 ML KIT DAP MINWIGGLER USB KIT DALI RGB XC836 DKV4 Figure 17 Programming the Control Gear using DAP miniWiggler Application Note 16 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Getting started DALI BUS Connect to 2 DALI BUS 1X1 KIT DALI RGB XC836 DKV4 DALI BUS Connector Connector X 1 Infineon DALI Control Gear KIT DALI RGB XC836 DKV1 DALI PHY X1 31Q DALI RX VX84C2V7 L e SFH615A 3 OK2 VCC Figure 18 Connecting the DALI Control Gear 2 5 3 Connecting DALI Master and Slave to the DALI Bus The DALI network can be setup with the following steps 1 To supply power for the DALI bus connect 1000 resistors in series to each terminal of a power supply unit supplying 15VDC This supplies the DALI bus for the DALI network devices 2 Connect the DALI Control Device Master and Control Gear Slave to the DALI bus This completes the DALI setup to control the devices using LightNet Application Note 17 V1
14. Min Level Indicates the physical minimum level of the selected device Maximum Level Indicates the maximum level of the selected device Minimum Level Indicates the minimum level of the selected device Power ON Level Indicates the power on level when turn on of the selected device System Failure Level Indicates the system failure level of the selected device Versioning Indicates the version number V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 LightNet Tool 3 5 Memory Access Control Tab This section describes the options for memory access feature Memory Bank Window Factory Settings Description This shows the contents of the memory banks Describes the memory settings Select the required memory contents for read or write supported for Bank O and 1 Clicking this window opens up the Memory Access Input Dialog address of last accezzbile memory location checksum of memory bank 001 of last acc mem bank memory bank 1 lack byte TIM byte 0 MSE DET GTIM byte 0 ISB TIM byte 1 DET GTIM byte 1 TIM byte 2 DET GTIM byte 2 TIM byte 3 DET GTIM byte 3 TIM byte 4 DEM TIM byte 4 TIM byte 5 DET TIM byte 5 Chl gear Firmware wer major OEM serial byte 1 T T53ES ciri gear Firmware wer minor OEM serial byte Z Serial number byte 1 ISE OEM serial byte 3 serial number bute Z OEM serial byte 4 LSB Serial number byte 3 Subsystem 4 7 Device 0 3 Retieve Facto
15. Settings serial number byte 4 Lamp type lockable add ctrl gear information Lamp type dt Retrieve Factory Settings This option retrieves the memory bank contents settings Note This operation takes a few seconds to complete Figure 28 Memory Bank Window Address Hex Displays the address of the user selected memory cell from the Memory Bank Window Memory bank Selection Selects Memory Bank 0 or 1 Read Button Executes the read command Write ButtonSelection Executes the write memory command Content Hex User entered content for the selected memory cell This operation is supported for memory bank 1 when memory bank 1 lock byte is 55h in accordance with IEC62386 Figure 29 Memory Input Dialog Application Note 23 V1 4 2012 10 4 Guide to using the DALI LightNet tool Infineon AP08104 Summary Summary Infineon s LightNet tool models the function of a lighting control device controlling DALI control gears This document demonstrates how easy the tool is to use to evaluate a DALI system 9 1 2 3 4 9 References IEC 62386 Digital addressable lighting interface Part 101 General requirements System Edition 1 0 2009 06 IEC 62386 Digital addressable lighting interface Part 102 General requirements Control gear Edition 1 0 2009 06 AP08102 DALI Control Gear Software Stack XC82x User Manual 1 1 Hardware Manual Easy Kit XC822 TSSOP16 board V1 0 XC83x User Manua
16. eon Technologies if a failure of such components can reasonably be expected to cause the failure of that life support device or system or to affect the safety or effectiveness of that device or system Life support devices or systems are intended to be implanted in the human body or to support and or maintain and sustain and or protect human life If they fail it is reasonable to assume that the health of the user or other persons may be endangered Guide to using the DALI LightNet tool Infineon AP08104 XC83x Revision History V1 4 2012 10 Previous Version s V1 3 Page Subjects major changes since last revision Updated DALI Control Gear Schematic Part 1 Changed R5 from 1K to 560R Trademarks We Listen to Your Comments Is there any information in this document that you feel is wrong unclear or missing Your feedback will help us to continuously improve the quality of this document Please send your proposal including a reference to this document to mcdocu comments infineon com Application Note 3 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Table of Contents Table of Contents 2 1 2 2 2 3 2 4 2 5 2 5 1 2 5 2 2 9 3 3 1 3 2 3 3 3 4 3 5 Overview Pr 5 Getting started sedi opti mma eaves P IE cued eSeded Pe bad bowen Sees 7 AP08104 Software Package 1 ce eee eee eee 7 LightNet Installation 0 0 0 eee eee eens 8 DALI Cont
17. et Setup Wizard Setup has finished installing Light et on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup Figure 11 LightNet tool setup completed Application Note 11 V1 4 2012 10 Guide to using the DALI LightNet tool AP08104 Infineon Getting started General Control amp Status Detailed Configuration Memory Access Control E33 Cantral MGa Ta Scenes ON amp Step Up C Scene C Scene 8 2 Down amp up Step Up C Scene Scene 9 Supported Address C Scene C Scene 10 ET SeDiedARC Direct ARC ow Step Down C Scene3 P Scene i Minimum C Scene4 Y Scene 12 E C Seene B C Scene 13 C Sceneb Scena 14 Cenirel Gea OK Fade Running NO C Scene Scene 15 NO lesel State NO Lamp Failure NO Reset State No CEDE Lamp Arc Power oN Miss Short Addr NO Limit Error IND Power Failure Actual Level 220 Device Type 0 eio desde eee A EA A nM a RA ee A LA M a LS DANOK i E T EET i n ps Hen ki HHR DOERR HOH General Control amp Status Detailed Configuration Memory Access Control Device Infomation Configuration Settings ERE SI anen tne Scenes gt Powwet Level Status Scene 0 T r sa Scene 0 20 Scene 1 100 Scene 2 DB Scene 3 250 Scene 4 DHT Scene 5 255 Scene 8 255 Scene 3 255
18. gure 33 Control Gear Board Schematics Part 2 Application Note 29 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 References DALI Control Gear KIT DALI RGB XC836 DKV1 BACK Figure 34 Control Gear Board Layout Application Note 30 V1 4 2012 10
19. l 1 0 Hardware Manual Easy Kit XC836 TSSOP board V1 0 Application Note 24 V1 4 2012 10 Infineon Guide to using the DALI LightNet tool AP08104 APPENDIX DALI PHY Board References Infineon DALI PHY circuit construction to support device evaluation within a typical DALI network using the XC836 Easy Kit board This following figure shows the schematic for a DALI with the XC822 Easy Kit board PHY circuit construction that can be used Note The DALI PHY board design supports a DALI bus level from 14 5V to 22 5V The values of R1 and R4 can be adjusted to support a wider DALI bus voltage range if required Connect to DALI BUS M X1A 1 MKDSN1 5 2 5 08 X1A 2L j MKDSN1 5 2 5 08 I 4 v DD Connect to MCU Ee IC2CE SFH6136 24 DALI RX DALI PHY GND GND DALI TAD and RAD Easy Kit Connector Figure 30 DALI PHY Board Schematics Application Note 25 Note IFX DALI PHY Board connectors ensure usage configurability Depending on DALI Control Gear Software stack settings the DALI TX RX pins can be connected via jumpers to the corresponding pins on the Easy Kit connectors V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 References mni sena mee DALI 5555533 890000000050 gt B 5 a T E i BE Figure 31 Infineon DALI PHY Board and Layout Table 1 Bill of Material for DALI PHY
20. n of this software requires that you click the acceptance button below By clicking the acceptance button accept vau agree to have read the important notice set forth below and to be bound by the following term of use IF uou do not agree to the terms and conditions below click the button I do nat accept and the installation procedure will nat be started IF uou change uour mind later stop using the Software and delete all capies of the C do not accept the agreement c Back Cancel LightNet tool license agreement if Setup LightNet Select Destination Location Where should LightNet be installed A Setup will install LightNet into the following folder To continue click Next f you would like to select a different folder click Browse Program Files Infineon Technologi A least 1 6 MB of free disk space is required EN TRENT LightNet tool destination location selection Application Note 10 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Getting started iB Setup LightNet Heady to Install Setup is now ready to begin installing Light et on your computer Click Install to continue with the installation or click Back if vau want bo review or change any settings Destination location C Program FilessInfineon Technologies Lighth et Stark Menu folder Light et E Cancel Figure 10 LightNet tool installation start B Setup LightNet Completing the LightN
21. nd partition control Building Management System DALI Control Device s e g Control Panel Remote Controller software control with GUI support DALI Bus Figure 1 DALI system types Application Note 5 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Overview LightNET DALI configuration SW for groups and scenes XC83x XC83x DALI Slave Board DALI Slave Board XC83x XC83x SW Stack SW Stack S DNE DALI PHY PHY Easy Kit as i DALI Master Board S USB UART XC83x IBN PC Connector SW Stack PHY DALI BUS Figure 2 Block Diagram for DALI Control Device and Control Gear Infineon has developed a solution for control gears based on the published IEC standard The DALI Software Stack for Control Gear has been designed around the Infineon XC83x devices LightNet has been created to mimic the basic functions of a lighting control device and can therefore be used to evaluate the software This document describes the setup of the LightNet tool The following items are required for use with this application note e 1x XC836 Easy Kit to serve as a DALI Control Device KIT XC836 EK V1 e 1x DALI PHY KIT XC822 XC836 DALI e 1x XC836 DALI Slave KIT DALI RGB XC836 DKV1 including DALI Control Gear Software Stack AP08102 e Infineon DALI LightNet tool Application Note 6 V1 4 2012 10 Guide to using the DALI LightNet tool
22. nect Clicking on Disconnect initiates connection to E Disconnect initiates disconnection LightNet tool eset teint from LightNet tool Figure 21 Connecting the Board 3 2 Address Selection LightNet supports 3 types of DALI addressing Broadcast e Short Address e Group Address The user decides the type of addressing to be sent with each command by selecting from the available options For Group Address the user is required to add the group address to the detailed configuration settings tab as shown in Chapter 3 4 Broadcast Address Fixed address of OxFF is Supported Address NOTE sent with commands 1 Steps to adding group address Pie Broadcast Address and programming of short address can be found in Detailed Short Address C short Address 0 gt Configuration tab User selectable short address range from00 to 2 This selection allows user 63 vi Group Address U commands to be addressed with the various supported address types listed Group Address Group setting needs to be added by user Supports range from 00 to 15 Figure 22 Address Selection Application Note 19 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 LightNet Tool 3 3 General Control amp Status Tab This section describes the general device control and status functions ON amp Step Up Step Down amp OFF Up Maximum Turns on device if current
23. on XC836 Easy Kit boards This software must be downloaded to the XC836 Easy Kit board prior to calling the LightNet tool File AP0810413 LightNet XC800Master code exe In addition to control via LightNet touch pad control is available 2 4 DALI Control Gear Software The DALI Software for Control Gear has been developed on the XC83x devices to support the features specified in the International Standard IEC 62386 Part 102 for control gears This software includes application code for driving an LED module supplied with the XC836 DALI Control Gear KIT DALI RGB XC836 DKV1 Through a control device the LightNet software allows DALI commands to be issued to control the brightness of the LED module attached to the control gear This software must be downloaded to the XC836 DALI Control Kit For further details please refer to AP08102 DALI Control Gear Software Stack 2 5 Hardware Setup The LightNet tool acts as the software for the DALI Control Device used with the XC836 Easy Kit The following sections describe how to setup the LightNet tool to evaluate the DALI protocol PC Connection via USB UART AL y DALI Power Supply N 15V supply with 1000 resistors Control using to power up the DALI bus line LightNET Software DALI Master Board x M DALI Slave Board Control Device X Control Gear Comprising of KIT XC836 EK V1 KIT XC822 XC836 DALI Comprising of KIT DALI RGB XC836 DKV1 Figure 13 Hardware Setup
24. rol Device Software 1 0 0 ee eee eee 13 DALI Control Gear Software 0 0 0 0 ee eee eens 13 Hardware eup vg es eden KR N TER R ARR ee een bed eee 3 TAMPREM Nes d md ree seu oes Pe Ws 13 Setting up the Control Device for LightNet 0 0 ce ee 13 setting up the Control Gear as e eee eee nas 15 Connecting DALI Master and Slave to the DALI Bus llle 17 LightNet Tog nananana anaana 19 Connecting the LightNet tool 0 0 00 eee ee eee 19 Address Selection 2 0 0 ee eee ee ee eens 19 General Control amp Status Tab eee eee eee 20 Detailed Configuration Command Tab nanana aa aaa e ee ee ees 21 Memory Access Control Tab iussu sek uh cR RR xm Rd eu bdtaws EO ato S edad susan 23 lunt M 24 ISGIGFOHCBS Loss seed pees eee ho AUR SORTE REHAB IE SC ROS a eae RUD ALIO RUDI eee HIC ROS RR 24 APPENDIX DALI PHY Board leere re 25 APPENDIX DALI Control Gear Board 0 aaan aaa ees 28 Application Note 4 V1 4 2012 10 Guide to using the DALI LightNet tool Infineon AP08104 Overview 1 Overview Digital Addressable Lighting Interface DALI is a communication protocol for lighting control in buildings The interface was first described in the IEC60929 standard for fluorescent lamp ballast Annex E The standard was subsequently updated to include other lighting devices such as LED
25. state Turns off device if current state Dim up 200ms using the Sets device to Maximum level is OFF Otherwise set power is minimum level Otherwise selected Fade Rate No change without fading Turns on level 1 step higher immediately set power level 1 step lower if power level is already at device if current state is OFF without fading immediately without fading Maximum OFF Step Up Turns off device Set power level 1 step higher immediately without fading ight Control ON amp Step Up Id asinum Step Down Set power level 1 step lower i diately without fading Step Down amp OF Up Step Up immediately without fading Send Direct ARC Step Down Te Minimunr Minimum Sets device to Minimum level without fading Turns on device if current state is OFF Send Direct ARC Sends Direct ARC level command to device User entry for Down desired ARC level to be sent Dim down 200ms using the selected Fade Rate No change if Steps tosend direct ARC commands power level is already at 1 Enter user desired ARC level Minimum 2 Click on Send Direct ARC to send command to device Figure 23 Light Control Control Gear Fade Running Reset State Indicates if connected Status YES or NO Indicates if device is in control gear is functional Get Status reset state Status OK or NO Click on this to obtain Status YES or NO current device status Lamp Failure Indicates if connected lamp has failure Missing Short
26. teps to Join Remove group 1 Select the desired group from the drop down list provided 2 Click on the radio button for the desired action Join Remove Scene Level Selects the scene for selected device to be set or removed To set the scene level user can enter desired scene level in the level field provided Steps to Set Remove Scene info 1 Select the desired scene from the drop down list provided 2 Enter the desired level in the Level field Skip this step if intention is to remove scene 3 Click on the radio button for the desired action Set Remove Device Enable Type Set the device enable type Supported types 0 and 6 Steps to enable type settings 1 Select from drop down list Once setting new setting takes effect Figure 26 Configuration Settings Application Note Configuration Settings f Join figs E E t Remove Scene it 0 Pee EX Remove Frogram Short Addr lt b Program Fade Control Settings Time l Hate 1 Power Control Setting Type DTR Max Lev Set Level Device Enable Type Reset Reset selected device to reset condition 21 Program Short Addr Programs user selected short address to connected device Range 0 to 63 Steps toProgram Short Address 1 Select from drop down list desired short address 2 Click on Program button Once completed new setting takes effect Time Rate Selects the device
Download Pdf Manuals
Related Search