HDSICM ONE WAY INTERCOM USER`S MANUAL
Contents
1. HDSICM ONE WAY INTERCOM USER S MANUAL Avire Inc 415 Oser Avenue Suite Q Hauppauge New York 11788 Phone 631 864 3699 Toll Free 800 527 9156 l Fax 631 864 2631 Email sales us avire global com Janus is a brand of Avire i l www avire global com www januselevator com TABLE OF CONTENTS SECTION FEATURES OPERATION PRE TESTING INSTALLATION DUPLEX SYSTEM SAMPLE DIAGRAM TROUBLESHOOTING WARRANTY POLICY RETURN POLICY FEATURES Complies with the 1996 Code for machine room to cab communications Simple off hook operation Easy installation with one pair wiring Battery backup Call is initiated from Machine Room phone only Wall mounted phone with handset for machine room Available in multi button models for multiple cabs Cab unit can mount on ceiling using provided enclosure or can be mounted behind speaker pattern if removed from enclosure OPERATION Remove the handset from the telephone and it will automatically establish communication with the elevator unit If there are 2 or more buttons on the telephone press the appropriate button to establish communication with the unit you need to communicate with To end the call simply just hang up the handset to the cradle PRE TESTING 1 Remove intercom system from shipping box If you want to test the intercom before installation connect a pair of wires from the white terminal strip to the TELCO block on the cab unit Be sure that the positiv2. connect one pair of wires between the European connector of the Machine Room telephone to the TELCO connector of the elevator unit This connection is polarity sensitive so be sure to connect the wiring so that the positive is on the No 2 terminal On multi button telephones there will be a white terminal strip at the Machine Room phone with a connection for each cab unit When you connect the wiring at the TELCO connector be sure that the positive is connected to the No 2 side of the connector Positive and negative are marked on the board DUPLEX SYSTEM SAMPLE DIAGRAM LTC SM FL HDSICM TROUBLESHOOTING Make sure that the Machine Room phone is getting power from the AC transformer by checking the voltage on the battery snap There should be approximately 13 volts DC with the handset on hook There should be positive voltage on the female side of the connector and negative voltage on the male side If the polarity is not correct reverse the wires coming from the wall transformer Make sure the wall phone is powered by taking the handset off hook and pressing any of the digits There should be tones heard in the handset If no tones are heard check the connections to the power supply Make sure the 9 volt battery is charged If you have less than 8 volts you can temporarily replace it with any charged 9 volt battery for testing purposes The 9 volt battery supplied with the unit is rechargeable and will build up to full char
3. e side of the European connector is connected to the positive side of the TELCO block See markings on the connector and on the PC board beside the TELCO block for proper terminal designations Plug the AC power supply into 110VAC outlet and connect the 9 volt battery to the battery snap Take the elevator unit into an adjoining room and close the door The person at the machine room phone should pick up the handset If it is a simplex unit no pushbuttons communication can begin If the unit is a duplex 2 button or triplex 3 button the person needs to press the appropriate pushbutton to communicate with the elevator cab unit 5 Check each elevator unit in the same manner INSTALLATION The intercom system requires one pair wiring for each elevator unit to the machine room phone The intercom system requires 110 volts AC to trickle charge the battery The wiring from the AC plug can be extended as needed to get to the nearest outlet Connectors are provided for this purpose Install the elevator unit on the ceiling using the mounting holes provided in the galvanized box The elevator unit can be mounted behind a speaker grill in the car operating panel 3 5 inch minimum diameter speaker pattern required by removing the intercom board from the galvanized enclosure Install the machine room telephone on the wall using an RJ11W or equivalent Connect the AC power to the machine room telephone For Simplex installations
4. ge after a couple of hours connected to the power supply Check to make sure voltage is being sent to the European connectors WITH THE HANDSET OFFHOOK and THE APPROPRIATE PUSH BUTTON PRESSED if not simplex check to see if you have 9 13 volts DC to the European connector to the selected elevator cab Check to make sure the cab unit is getting voltage WITH THE HANDSET OFFHOOK and THE APPROPRIATE PUSHBUTTON PRESSED If not simplex measure the DC voltage atthe TELCO connector There should be 9 13 volts Make sure that polarity is correct positive voltage on the No 2 and negative voltage on No 1 connector The CMU intercom in the elevator cab does not require a 9 volt battery 6 You can test each cab unit individually and without any field wiring connected by attaching a 9 volt battery to the battery connector that is soldered directly onto the PC board and plugging a modular tone phone into the black jack on the back of the board You should be able to communicate through the handset to the PC board WARRANTY POLICY Avire Inc warrants its products to be free from defect in materials and workmanship under normal use and service for 24 months from date of purchase Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any product which proves defective in materials or workmanship under normal use and service Avire shall not be responsible for any damage to the
5. unit incurred during installation Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Avire factory service For warranty service contact Avire at 631 864 3699 or 800 527 9156 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT RETURN POLICY During installation if a product does not appear to function properly the installer must call the Avire Technical Support Unit at 800 527 9156 Monday through Friday If the technician determines that the product is not functioning an RA Return Authorization number will be issued allowing the installer to return the product directly to Avire for repair replacement or credit Returns with no fault found will result in a bench charge plus shipping costs Returns without an RA number will result in a restocking charge of 25 or more plus shipping costs Need Technical Assistance Call 1 800 527 9156
Download Pdf Manuals
Related Search