Industrial Computing Solutions Industrial Motherboards
Contents
1. Customers shall enclose the NEXCOM RMA Service Form with the returned packages Customers must collect all the information about the problems encoun tered and note anything abnormal or print out any on screen messages and describe the problems on the NEXCOM RMA Service Form for the RMA number apply process Customers can send back the faulty products with or without acces sories manuals cable etc and any components from the card such as CPU and RAM If the components were suspected as part of the prob lems please note clearly which components are included Otherwise NEXCOM is not responsible for the devices parts Customers are responsible for the safe packaging of defective products making sure it is durable enough to be resistant against further damage and deterioration during transportation In case of damages occurred during transportation the repair is treated as Out of Warranty Any products returned by NEXCOM to other locations besides the cus tomers site will bear an extra charge and will be billed to the customer Repair Service Charges for Out of Warranty Products NEXCOM will charge for out of warranty products in two categories one is basic diagnostic fee and another is component product fee System Level Component fee NEXCOM will only charge for main components such as SMD chip BGA chip etc Passive components will be repaired for free ex resistor capacitor2. 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Chapter 1 Introduction N COM 1 4 Motherboard Layout N m U amp 5 6 78910 11 a Keyboard IT USB 1 Wwos1 E Mouse B USB 0 Tow M SA TA 1 VGA1 COM1 AE O MINI_PCIE1 DDR3_A1 DDR3_A2 COM2 HDMI 39 38 37 USB 2 0 T USB 3 RJ 45 B USB 2 36 USB 2 0 T USB 5 RJ 45 B USB 4 000 N O Cn KRW 19 ue9 u eur dol ino eur UL DIN uonog 0 Designe din Taipei 35 34 33 32 29 3031 28 27 26 2524 23 22 NEX 611 User Manual Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 4 Chapter 1 Introduction N COM 1 Mini SATA Slot M_SATA1 32 PCI Express Slot PCIE1 2 LVDS Connector LVDS1 33 Vertical Type A USB USB12 3 Backlight Power Jumper BKT_PWR1 34 Audio AMP Output Speaker Header SPEAKER_OUT1 4 Inverter Power Control Header BLT_PWR2 35 Front Panel Audio Header HD_AUDIO1 5 Panel Power Jumper PNL_PWR1 36 TPM header TPM1 6 Backlight amp
3. Items will be replaced with NEXCOM products if the original one cannot be repaired Ex motherboard power supply etc Replace with 3rd party products if needed If RMA goods can not be repaired NEXCOM will return it to the cus tomer without any charge Board Level Component fee NEXCOM will only charge for main components such as SMD chip BGA chip etc Passive components will be repaired for free ex resistors capacitors If RMA goods can not be repaired NEXCOM will return it to the cus tomer without any charge NEXCOM Zh Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Preface Warnings Read and adhere to all warnings cautions and notices in this guide and the documentation supplied with the chassis power supply and accessory modules If the instructions for the chassis and power supply are incon sistent with these instructions or the instructions for accessory modules contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements Cautions Electrostatic discharge ESD can damage system components Do the de scribed procedures only at an ESD workstation If no such station is avail able you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis Safety Information Before installing and using the device note the following precauti
4. No 12 SLCT GND PE GND BUSY GND ACK GND SPD7 GND SPD6 GND SPD5 GND SPD4 GND SPD3 SLIN SPD2 PINIT SPD1 ERROR SPDO AFD STB Pin Signal Name Pin Signal Name Pin Signal Name 1 STB 2 SPDO 3 SPD 1 4 SPD2 5 SPD3 6 SPD4 7 SPD5 8 SPD6 9 SPD7 10 ACK 11 BUSY 12 PE 13 SLCT 14 AFD 15 ERROR 16 PINIT 17 SLIN 18 GND 21 GND 22 GND 24 GND 25 GND Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 11 NEX 611 User Manual Chapter 2 Installation N COM 9 pin HD_AUDIO1 wire on the chassis must support HDA to function correctly see p 10 No 35 Please follow the instructions in our manual and chassis AS manual to install your system Front Panel Audio Header 1 High Definition Audio supports Jack Sensing but the panel 2 If you use an AC 97 audio panel please install it to the front panel audio header by the steps below A Connect Mic_IN MIC to MIC2_L B Connect Audio_R RIN to OUT2_R and Audio_L LIN to OUT2_L C Connect Ground GND to Ground GND D MIC_RET and OUT_RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E To activate the front mic Pin Signal Name Pin Signal Name For Windows XP XP 64 bit OS i Mice 2 MIC2_R Select Mixer Select Recorder Then click FrontMic SEU L For Windows 8 8 64 bit 7 7 64 bit VistaTM VistaTM 5 OUT2_L 6 GN
5. or 1 000ppm In order to meet the RoHS compliant directives NEXCOM has established an engineering and manufacturing task force in to implement the introduction of green products The task force will ensure that we follow the standard NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned a RoHS Compliant The model selection criteria will be based on market demand Vendors and suppliers will ensure that all designed components will be RoHS compliant DERE How to recognize NEXCOM RoHS Products For existing products where there are non RoHS and RoHS versions the suf fix LF will be added to the compliant product name All new product models launched after January 2006 will be RoHS compli ant They will use the usual NEXCOM naming convention NEXCOM Zh Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Preface Warranty and RMA NEXCOM Warranty Period NEXCOM manufactures products that are new or equivalent to new in accordance with industry standard NEXCOM warrants that products will be free from defect in material and workmanship for 2 years beginning on the date of invoice by NEXCOM HCP series products Blade Server which are manufactured by NEXCOM are covered by a three year warranty period NEXCOM Return Merchandise Authorization RMA
6. F1 To display the General Help Screen F7 Discard changes F9 To load optimal default values for all the settings lt F10 gt To save changes and exit the UEFI SETUP UTILITY lt F12 gt Print screen lt ESC gt To jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the UEFI Setup Utility the Main screen will appear and display the system overview Aptio Setup Utility Copyright C 2011 American Megatrends Inc System Date Copyright 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Chapter 3 Uefi Setup Utility EE 3 3 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Nouth Bridge Configuration South Bridge Configuration Storage Configuration Super IO Configuration ACPI Configuration USB Configuration and Trusted Computing Aptio Setup Utility Copyright C 2011 American Megatrends Inc CPU configuration an Setting wrong values in this section may cause the system to malfunction Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 28 NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 3 1 CPU Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Cool n Quiet Use this to enable or disable AMD s Cool n QuietTM technology The default value is Enabled Configuration options Enabled and D
7. M Vista 64 bit XP XP 64 bit on your system CER 2 8 2 Installing Windows 8 64 bit 7 64 bit VistaTM 64 bit on a HDD Larger than 2 terabytes 2TB without RAID This motherboard adopts UEFI BIOS that allows Windows OS to be installed on a large size HDD gt 2TB Please make sure to use Windows VistaTM 64 bit with SP2 or above 7 64 bit or 8 64 bit and follow the procedures below to install the operating system Using AHCI Mode STEP 1 Set Up UEFI Press F2 or Delete at system POST Set AHCI Mode in UEFI Setup Utility Advanced Storage Configuration SATA Mode STEP 2 Press lt F11 gt to launch boot menu at system POST and choose the item UEFI lt Optical disk drive gt to boot STEP 3 Start Windows installation Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Chapter 2 Installation 2 8 3 Installing Windows 8 8 64 bit 7 7 64 bit VistaTM VistaTM 64 bit with RAID RAID mode is not supported under Windows XP STEP 1 Set Up UEFI Press lt F2 gt or lt Delete gt at system POST Set RAID Mode in UEFI Setup Utility gt Advanced gt Storage Configuration gt SATA Mode STEP 2 Use RAID Installation Guide to set the RAID configuration Before you start to configure RAID you need to check the installa tion guide in the Support CD for proper configuration Please refer to the document in the Support CD Guide to SATA H
8. NEX 611 User Manual Chapter 2 Installation N COM 2 7 Expansion Slots PCI PCI Express and mini PCle Slots There are 2 PCI slots 2 PCI Express slots and 1 mini PCle slot on this moth Clear CMOS Jumper erboard Jumper Setting 3 pinCLRCMOS1 ono Co cee Naar Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS To clear and reset the sys tem parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS action Please be noted that the password date time user default profile 1394 GUID and MAC address will be cleared only if the CMOS battery is removed NEXCOM Ei Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 18 NEX 611 User Manual Chapter 2 Installation N COM Backlight Power Jumper Jumper Setting Description 3 pin BKT_PWR1 1 2 5V see p 10 No 3 123 2 3 412V Panel Power Jumper Jumper Setting Description 3 pin PNL_PWR1 1 2 3V see p 10 No 5 123 2 3 45V PWR On Mode Jumper Jumper Setting Description 3 pin PWR JP1 1 2 AT Mode see p 10 No 21
9. Plug Hot Swap Improper procedures will cause the HDD damage and data loss Please connect the SATA power TII Connect the SATA data cable s 1x4 pin end White cable to the motherboard s to the power supply s 1x4 pin SATA connector cable SATA power cable 1x4 pin power connector White Connect the SATA 15 pin power cable connector s Black end to the HDD Pe SEI Connect the SATA data cable to the HDD NEXCOM Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved How to Hot Unplug Hot Swap a HDD Please follow the instructions below to process Hot Unplug Hot Swap Improper procedures will cause the HDD damage and data loss Unplug the SATA data cable from the HDD s side Unplug the SATA 15 pin power cable connector Black from the HDD s side E an NEX 611 User Manual Chapter 3 Uefi Setup Utility EE CHAPTER 3 Uefi Setup UTILITY 3 1 Introduction This section explains how to use the UEFI Setup Utility to configure your system The UEFI chip on the motherboard stores the UEFI Setup Utility You may run the UEFI Setup Utility when you start up the computer Please press lt F2 gt or lt Del gt during the Power On Self Test POST to enter the UEFI Setup Utility otherwise POST will continue with its test routines If you wish to enter the UEFI Setup Utility after POST restart the system by pressing lt Ctl gt lt Alt gt lt Delete gt or by pre
10. Video Repost Enabled Enabled Please set this option to Enabled if you plan to use this mother board to submit Windows Vista certification PS 2 Keyboard Power On Use this to enable or disable the PS 2 keyboard to turn on the system from power soft off mode PCI Devices Power On Use this to enable or disable the PCI devices to turn on the system from power soft off mode Ring In Power On Use this to enable or disable the Ring In signals to turn on the system from power soft off mode RTC Alarm Power On Use this to enable or disable the RTC Real Time Clock to power on the system S3 Video Repost Use this to enable disable S3 Video Repost The default value is Enabled USB Keyboard Remote Power On Kpr ETAN Use this to enable or disable the USB Keyboard Remote to power on the Use this to select whether to auto detect or disable Suspend to RAM system Select Auto to enable if the OS supports it USB Mouse Power On Check Ready Bit Use this to enable or disable the USB Mouse to power on the system Use this to enable or disable Check Ready Bit Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 34 NEX 611 User Manual Chapter 3 Uefi Setup Utility EE 3 3 7 USB Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc USB 2 0 Controller Enabled USB 2 0 Controller Use this to enable or disable the USB 2 0 controller Copyright O 2011 NEXCOM Inte
11. connections as these can damage the soft metal or plastic parts of the connectors NEXCOM Zh Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Preface Safety Precautions 1 2 3 10 17 Read these safety instructions carefully Keep this User Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning For plug in equipment the power outlet socket must be located near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a stable surface during installation Dropping it or letting it fall may cause damage Do not leave this equipment in either an unconditioned environment orin a above 40 C storage temperature as this may damage the equipment The openings on the enclosure are for air convection to protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connect ing the equipment to the power outlet Place the power cord in a way so that people will not step on it Do not place anything on top of the power cord Use a power cord that has been approved for use with the product and that it matches the voltage and current marked on the product s electrical range label The voltage and current rating of the cord must be greater than the voltage and curren
12. for attention before you process Hot Plug Hot Swap 1 Without the SATA 15 pin power connector interface Hot Plug Hot Swap cannot be processed N Even though some HDDs provide both SATA 15 pin power connectors and IDE 1x4 pin conventional power connectors IDE 1x4 pin conven tional power connector s interface is definitely unable to support Hot Plug Hot Swap and will cause the HDD damage and data loss UJ The operation procedure below is designed only for our motherboard which supports Hot Plug Hot Swap Hot Plug Hot Swap might not be supported by the chipset because of its limitation The support information of our motherboards are indicated in the product spec on our website www nexcom com 4 Make sure your HDDs can support Hot Plug Hot Swap from your dealer or HDD user manual HDDs that do not support Hot Plug Hot Swap will be damaged ul Please make sure that the required SATA drivers are installed properly The latest SATA drivers are available on our support website www nexcom com Oo Make sure to use the SATA power cable amp data cable from our motherboard package N Please follow the instructions below step by step to reduce the risk of HDD crash or data loss NEXCOM Ei Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 24 NEX 611 User Manual Chapter 2 Installation How to Hot Plug Hot Swap a HDD Please follow the instructions below to process Hot
13. the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove the bracket facing the slot that you intend to use Keep the screws for later use Step 3 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 4 Fasten the card to the chassis with screws 2 3 Installing SATA Hard Disks Step 1 Connect the SATA power cable to the hard disk Step 2 Connect one end of the SATA data cable to the hard disk Step 3 Align the card connector with the slot and press firmly until the card is completely seated on the slot Serial ATA3 Connectors SATA3 1 see p 10 No 17 SATA3 3 SATA3 4 SATA3 2 see p 10 No 15 1I J Ir SATA3 3 see p 10 No 16 SATA3_4 see p 10 No 14 SATA3 1 SATA3 2 These four Serial ATA3 SATA3 connectors support SATA data cables for internal storage devices The current SATA3 interface allows up to 6 0 Gb s data transfer rate Copyright 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Chapter 2 Installation 2 4 Power Connectors ATX 12V Power Connector 4 pin ATX12V1 see p 10 No 10 Please connect a power supply to this connector HH SATA Power Connector 4 pin JPWR1 see p 10 No 13 Itis not necessary to use this connector but please connect it with a hard disk power connector when two g
14. voltage and Automatic Model The default value is Full On Aptio Setup Utility Copyright C 2011 American Megatrends Inc CPU FANI amp Setting Full on Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 37 NEX 611 User Manual Chapter 3 Uefi Setup Utility 3 5 Boot Screen This section displays the available devices on your system for you to config ure the boot settings and the boot priority Aptio Setup Utility Copyright C 2011 American Megatrends Inc Boot Option 1 UEFI Built in EFL Setup Prompt Timeout This shows the number of seconds to wait for the setup activation key Bootup Num Lock If this is set to On it will automatically activate the Numeric Lock after boot up PCI ROM Priority Use this item to adjust PCI ROM Priority The default value is Legacy ROM Boot From Onboard LAN Use this to enable or disable Boot From Onboard LAN Copyright 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 6 Security Screen In this section you may set or change the supervisor user password for the system You may also clear the user password Aptio Setup Utility Copyright C 2011 American Megatrends Inc Supervisor Password Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 39 NEX 611 User Manual Chapter 3 Uefi Setup Utility EE 3 7 Exit Screen Aptio Setup Util
15. 1 23 2 3 AXT Mode COM Power Setting Jumpers Jumper Setting Description 5 pin SET_CM1 5 see p 10 No 40 pin SET_CM2 12 412V see p 10 No 39 11010101010 2 3 45V see p 10 No 24 5 pin SET CM4 see p 10 No 26 5 pin SET CM3 4 5 RRI Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 19 NEX 611 User Manual Chapter 2 Installation 2 8 Operating System Setup This motherboard supports various Microsoft Windows operating systems 8 8 64 bit 7 7 64 bit Vista M Vista M 64 bit XP XP 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer your OS documentation for more information 2 8 1 Installing Windows 8 8 64 bit 7 7 64 bit Vista Vista M 64 bit XP XP 64 bit without RAID Using AHCI Mode AHCI mode is not supported under Windows XP STEP 1 Set Up UEFI Press lt F2 gt or lt Delete gt at system POST Set AHCI Mode in UEFI Setup Utility gt Advanced gt Storage Configuration gt SATA Mode STEP 2 Install Windows 8 8 64 bit 7 7 64 bit VistaTM VistaTM 64 bit on your system Using IDE Mode STEP 1 Set Up UEFI Press lt F2 gt or lt Delete gt at system POST Set IDE Mode in UEFI Setup Utility gt Advanced gt Storage Configuration gt SATA Mode STEP 2 Install Windows 8 8 64 bit 7 7 64 bit Vista
16. Amp Volume Control Header BLT_VOL1 37 SPI Flash Memory 32Mb 7 CPU Fan Connector CPU_FAN1 38 Chassis Fan Connector CHA_FAN1 8 CPU 39 COM Power Setting Jumper SET CM2 9 AMD A50M A55E Chipset 40 COM Power Setting Jumper SET_CM1 10 4 pin ATX 12V Power Connector 41 Mini PCI Express Slot MINI_PCIE1 11 2 x 204 pin DDR3 SO DIMM Slots DDR3_A1 DDR3 A2 Black 12 Printer Port LPT1 FOptional 13 SATA Power Connector JPWR1 14 SATA3 Connector SATA3_4 White 15 SATA3 Connector SATA3_2 White 16 SATA3 Connector SATA3_3 White 17 SATA3 Connector SATA3_1 White 18 COM Port Header COM3 19 COM Port Header COM4 20 System Panel Header PANEL1 21 PWR On Mode Jumper PWR_JP1 22 COM Port Header COM6 23 COM Port Header COM5 24 COM Power Setting Jumper SET CM3 25 Digital O Header DIO1 26 COM Power Setting Jumper SET CM4 27 Clear CMOS Jumper CLRCMOS 1 28 Buzzer BUZZ1 29 USB 2 0 Header USB6 7 30 USB 2 0 Header USB8 9 31 USB 2 0 Header USB10 11 PS o NEXCOM E Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 5 NEX 611 User Manual Chapter 1 Introduction 1 5 I O Panel There are two LED next to the LAN port Please refer to the table below for the LAN port LED indications 13 12 11 10 9 8 e 1 USB 2 0 Ports USBO1 e 3 USB 2 0 Ports USB45 e 2 Serial Port COM1 e 3 Serial Port COM2 9 USB 2 0 Ports USB23 10 HDMI Port HDMI1 LAN Port LE
17. D PRESENCE 8 MIC_RET 64 bit OS 10 OUT RET Go to the FrontMic Tab in the Realtek Control panel Adjust Recording Volume NEXCOM m Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 12 NEX 611 User Manual Chapter 2 Installation Audio AMP Output Speaker Header 4 pin SPEAKER_OUT1 see p 10 No 34 oump OUIRN Chassis Fan Connector 3 pin CHA FAN1 see p 10 No 38 Please connect a fan cable to the fan connector and match the black wire to the ground pin a goo GND 1 12V FAN_SPEED 1 Pin Signal Name Pin Signal Name Pin Signal Name Pin Signal Name 1 SPK L 2 SPK L 1 FAN SPEED 2 12V 3 SPK R 4 SPK R 3 GND Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 13 NEX 611 User Manual Chapter 2 Installation CPU Fan Connector 4 pin CPU FAN1 see p 10 No 7 Though this motherboard provides a 4 Pin CPU fan Quiet Fan connector 3 Pin CPU fans can still work successfully even without fan speed control If you plan to connect a 3 Pin CPU fan please connect it to Pin 1 3 FAN SPEED CONTROL Pin Signal Name Pin Signal Name 1 GND 2 12V 3 FAN_SPEED 4 FAN_SPEED_CONTROL Serial Port Header 9 pin COM3 see p 10 No 18 9 pin COM4 see p 10 No 19 9 pin COM5 see p 10 No 23 9 pin COM6 see p 10 No 22 These COM headers support serial port modules RRXD1
18. D Indications ACT LINK LED Activity Link LED SPEED LED LAN Port Activity Link LED e 4 LAN RJ 45 Port LAN2 11 HDMI Port HDMI2 e 5 LAN RJ 45 Port LAN1 e 12 D Sub VGA1 LL Description M eI 6 Front Speaker Lime e 13 PS 2 Keyboard Mouse Port Oh Melak pa connecyon e 7 Microphone Pink Blinking Data Activity Orange 100Mbps connection On 100Mbps connection Green 1Gbps connection Optional f a NEXCOM n Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 6 NEX 611 User Manual Chapter 2 Installation N COM CHAPTER 2 INSTALLATION This is a Mini ITX form factor motherboard Before you install the mother 2 1 Installing Memory Modules DIMM cred the configuration of your chassis to ensure that the mother This motherboard provides two 204 pin DDR3 Double Data Rate 3 oard Tits into it SO DIMM slots Pre installation Precautions Step 1 Unlock a DIMM slot by pressing the retaining clips outward Take note of the following precautions before you install motherboard Step 2 Align a DIMM on the slot such that the notch on the DIMM components or change any motherboard settings matches the break on the slot 1 Make sure to unplug the power cord before installing or removing the motherboard Failure to do so may cause physical injuries to you and damages to motherboard components N In order to avoid damage from static electricity to the motherboard s co
19. DDCD 1 Pin Signal Name Pin Signal Name 1 DDCD 1 2 TTXD1 3 GND 4 RRTS 1 5 RRI 1 6 RRXD1 7 DDTR 1 8 DDSR 1 9 CCIS 1 Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 14 NEX 611 User Manual Chapter 2 Installation N COM a TPM Header LVDS Connector Optional 17 pin TPM1 40 pin LVDS1 see p 10 No 36 see p 10 No 2 This connector supports Trusted Platform Module TPM system which can securely store keys digital certificates passwords and data A TPM system also helps enhance network security protects digital identities and ensures aa nll platform integrity E w co aaa gg 2 40 F CLKRUN GND SERIRQ 3VSB S_PWRDWN GND LADO_L LAD1_L x3V Pin Definition Pin Definition Pin Definition LADZ L LAD3_L 1 LVDS_PWR 2 LVDS_PWR 3 43V SMB DATA MAIN TPM RST SMB CLK MAIN LFRAME _L DDC_CLK 5 DDC_DATA 6 LVDS1 DO omy essen ets LVDS1 DO 8 GND 9 LVDS1 D1 VDS1 D1 11 GND 12 LVDS1 D2 VDS1 D2 14 GND 15 LVDS1 D3 Pin Signal Name Pin Signal Name Pin Signal Name VDS1 D3 17 GND 18 LVDSICLK 1 CK_33M_TPM 2 LFRAME _L 3 TPM_RST IVDS1CLK 30 GND 21 LvDS2 DOO LAD3_L 3 oy 6 LADO_L LVDS2 DO 23 GND 24 1VDS2 D1 raat 2 END 19 SNB LVDS2 D1 4 26 GND 27 lVDS2 D2 11 SMB_CLK
20. NEXCOM International Co Ltd Industrial Computing Solutions Industrial Motherboards NEX 611 User Manual NEXCOM International Co Ltd Published September 2013 www nexcom com Contents CONTENTS Preface Chapter 2 Installation Copyrigt teria ds iv 2 1 Installing Memory Modules DIMM aa 7 Disclaiff b ic atico iv 2 2 Expansion Slots PGI Express Slots icr se rette ee 8 Acknowledgetnerits sicario el etx gene AA iv 2 3 Installing SATA Hard DISKS ecce ir a eta 8 Regulatory Compliance Statements sss iv 2 4 POWeTICOCFIIGCLOTS osse terae ret sigan GSA dex dap orti A Ren queda 9 Declaration of Conformity esse dier tortas iv 2 5 Installing the System Panel sss 10 RoHS Compliance sian nn ban anda e a a A ad V 2 6 Onboard Headers and Connectors ssssssssssees 11 Warranty and RM Ap ann nn a a eee nenne nenne nennen nnne innare vi 2 7 Expansion Slots PCI PCI Express and mini PCle Slots 18 Safety Informationi ete a ice b dct ee i tut vii 2 8 Operatinig Systemi Setup iue nette tet tut een pedi tad 20 Installation Recommendations nisione a eka vii 2 9 Installing DIV Grita ir 22 Safety Precautiofis sc s apodaca viii 2 10 Hot Plug and Hot Swap for Hard Disk Drives 23 Technical Support and Assistance aaa ix Conventions Used in this Manual ix Chapter 3 UEFI Setup utility G
21. OAB United Kingdom Tel 44 1908 267121 Fax 44 1908 262042 Email sales uk nexcom eu www nexcom eu xi ma NEX 611 User Manual Chapter 1 Introduction CHAPTER 1 INTRODUCTION Thank you for purchasing NEXCOM NEX 611 motherboard a reliable motherboard produced under NEXCOM consistently stringent quality control It delivers excellent performance with robust design conforming to NEXCOM commitment to quality and endurance In this manual chapter 1 and 2 contains the introduction of the motherboard and step by step hardware installation guide Chapter 3 and 4 contains the configuration guide of BIOS setup and information of the Support CD might be updated the content of this manual will be subject to change without notice In case any modifications of this manual occur the updated version will be available on NEXCOM website without further notice You may find the latest VGA cards and CPU support list on NEXCOM website as well NEXCOM website http Awww nexcom com If you require technical support related to this motherboard please visit our website for specific information about the model you are using http www nexcom com Inquiry InquiryModel Because the motherboard specifications and the BIOS software Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 1 1 Package Contents NEXCOM NEX 611 Motherboard Mini ITX Form Factor 6 7 in x 6 7 in 17 0 cm x 17 0 cm NEXCOM NEX 611 Quick Installation G
22. _MAIN 12 SMB_DATA_MAIN 13 LAD2_L VDS2 D26 25 ne ER 30 LVDS2 D3O 1 LADI 13 ew 16 11 2 RMN LVDS2 D3 32 GND 33 LvDS2 CLK id SEDIS Wa PC RUNG VDS2 CLK 35 GND 36 B L ENABLE B L ADJUST 38 BLT_PWR 39 BLT_PWR BLT_PWR Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 15 NEX 611 User Manual Chapter 2 Installation N COM MAA Inverter Power Control Header Optional Backlight amp Amp Volume Control Header Optional 6 pin BLT_PWR2 7 pin BLT_VOL1 see p 10 No 4 see p 10 No 6 OO00000 1 1 Pin Signal Name Pin Signal Name Pin Signal Name Pin Signal Name 1 GND 2 GND 1 Volume UP 2 Volume DOWN 3 Panel Backlight Control 4 Panel Backlight Enable 3 PANEL PWR Down 4 Panel BackLight UP 5 Panel Backlight Power 6 Panel Backlight Power 5 Panel BackLight Down 6 GND 7 GND Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 16 NEX 611 User Manual Chapter 2 Installation Digital I O Header 10 pin DIO1 see p 10 No 25 Mini SATA Connector This mini SATA connector can be used to connect a Solid State Drive SSD for an internal storage device Or used for USB interface addon cards 00000 00000 1 Pin Signal Name Pin Signal Name 1 GP4 GPO 3 GP5 4 GP1 5 GP6 GP2 7 GP7 GP3 9 5V 10 GND Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 17
23. adio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area domestic environment is likely to cause harmful interfer ence in which case the user will be required to correct the interference take adequate measures at their own expense CE The product s described in this manual complies with all applicable Euro pean Union CE directives if it has a CE marking For computer systems to remain CE compliant only CE compliant parts may be used Maintaining CE compliance also requires proper cable and cabling techniques NEXCOM Zh Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Preface RoHS Compliance NEXCOM RoHS Environmental Policy and Status Update NEXCOM is a global citizen for building the digital infra structure We are committed to providing green products and services which are compliant with European Union RoHS Restriction on Use of Hazardous Substance in Electronic Equipment directive 2002 95 EU to be your trusted green partner and to protect our environment RoHS restricts the use of Lead Pb lt 0 1 or 1 000ppm Mercury Hg lt 0 1 or 1 000ppm Cadmium Cd lt 0 01 or 100ppm Hexavalent Chromium Cr6 lt 0 1 or 1 000ppm Polybrominated biphenyls PBB lt 0 1 or 1 000ppm and Polybrominated diphenyl Ethers PBDE lt 0 1
24. ard Disks Installation and RAID Configuration which is located in the folder at the following path RAID Installation Guide STEP 3 Install Windows 8 8 64 bit 7 7 64 bit VistaTM VistaTM 64 bit on your system Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 21 NEX 611 User Manual Chapter 2 Installation N COM 2 9 Installing Drivers The Support CD that comes with the motherboard contains necessary drivers and useful utilities that enhance the motherboard s features 2 9 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu does not appear automatically locate and double click on the file ASRSETUP EXE in the Support CD to display the menu 2 9 2 Drivers Menu The drivers compatible to your system will be auto detected and listed on the support CD driver page Please follow the order from top to bottom to install those required drivers Therefore the drivers you install can work properly 2 9 3 Utilities Menu The Utilities Menu shows the application softwares that the motherboard supports Click on a specific item then follow the installation wizard to install it 2 9 4 Contact Information If you need to contact NEXCOM or want to know more about NEXCOM you re welcome to visit NEXCOM website at http www nexcom com or you may conta
25. ct your dealer for further information NEXCOM Ei Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 22 NEX 611 User Manual Chapter 2 Installation N COM 2 10 Hot Plug and Hot Swap for Hard Disk Drives This motherboard supports Hot Plug and Hot Swap for SATA3 in AHCI Hot Plug Hot Swap Operation Guide RAID mode Raid is not supported by AMD A50M Please read the operation guide of Hot Plug Hot Swap below carefully Before you process Hot Plug Hot Swap please check the cable accessories What is Hot Plug and Hot Swap from the motherboard gift box pack below If the HDDs are NOT set for RAID it is called Hot Plug for the A 7 pin SATA data cable action to insert and remove the HDDs while the system is still B SATA power cable with SATA 15 pin power connector interface powered on and in working condition If the HDDs are set for RAID then it is called Hot Swap However please note that A SATA data cable Red B SATA power cable it cannot perform Hot Plug or Hot Swap if the OS has been installed into the HDD SATA The SATA 15 pin power The 1x4 pin 7 pin connector Black should conventional power connector be connected to your connector White SATA3 HDD should be connected to a power supply T NEXCOM Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 23 NEX 611 User Manual Chapter 2 Installation N COM Points
26. d copied translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co Ltd Disclaimer The information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co Ltd However users may update their knowledge of any product in use by con stantly checking its manual posted on our website http www nexcom com NEXCOM shall not be liable for direct indirect special incidental or consequential damages arising out of the use of any product nor for any infringements upon the rights of third parties which may result from such use Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed Acknowledgements NEX 611 is a trademark of NEXCOM International Co Ltd All other prod uct names mentioned herein are registered trademarks of their respective owners Regulatory Compliance Statements This section provides the FCC compliance statement for Class B devices and describes how to keep the system CE compliant Declaration of Conformity FCC This equipment has been tested and verified to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equip ment generates uses and can radiate r
27. erved ix NEX 611 User Manual Preface Global Service Contact Information Headquarters NEXCOM International Co Ltd 15F No 920 Chung Cheng Rd ZhongHe District New Taipei City 23586 Taiwan ROC Tel 886 2 8226 7786 Fax 886 2 8226 7782 www nexcom com tw America USA NEXCOM USA 2883 Bayview Drive Fremont CA 94538 USA Tel 1 510 656 2248 Fax 1 510 656 2158 Email sales nexcom com www nexcom com Asia Taiwan Taichung Office 16F No 250 Sec 2 Chongde Rd Beitun Dist Taichung City 406 R O C Tel 886 4 2249 1179 Fax 886 4 2249 1172 www nexcom com tw Japan NEXCOM Japan 9F Tamachi Hara Bldg 4 11 5 Shiba Minato ku Tokyo 108 0014 Japan Tel 81 3 5419 7830 Fax 81 3 5419 7832 Email sales nexcom jp com www nexcom jp com China NEXCOM China 2F Block 4 Venus Plaza Building 21 ZhongGuanCun Software Park No 8 Dongbeiwang West Road Haidian District Beijing 100193 China Tel 86 10 8282 5880 Fax 86 10 8282 5955 Email sales nexcom cn www nexcom cn Shanghai Office Room 1505 Greenland He Chuang Bldg No 450 Caoyang Rd Shanghai 200062 China Tel 86 21 6150 8008 Fax 86 21 3251 6358 Email sales nexcom cn www nexcom cn Nanjing Office Hall C Block 17 Tian Xing Cui Lang Bldg No 49 Yunnan North Rd Nanjing 210018 China Tel 86 25 8315 3486 Fax 86 25 8315 3489 Email sales nexcom cn www nexcom cn Shenzhen Office We
28. g Analysis and Reporting Technology SATA Controller Use this to enable or disable the SATA Controller SATA Mode Use this to select the SATA mode for SATA3_1 to SATA3_4 ports Configuration options IDE Mode AHCI Mode and RAID Mode The default value is IDE Mode Raid is not supported by AMD A50M a um Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 32 NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 3 5 Super IO Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc COM5 Configuration Use this to set parameters of COM5 COM6 Configuration gt COMI Configuration Use this to set parameters of COM6 LPT1 Port Configuration Use this set parameters of the onboard parallel port WDT Timeout Reset This allows users to enable disable the Watch Dog Timer timeout to reset system The default value is Disabled COM Configuration Use this to set parameters of COM1 COM2 Configuration Use this to set parameters of COM2 COM3 Configuration Use this to set parameters of COM3 COM4 Configuration Use this to set parameters of COM4 Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 33 NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 3 6 ACPI Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc ACPI HPET Table Use this to enable or disable the ACPI HPET Table The default value is S3
29. isabled If you have installed Windows 8 7 VistaTM and want to enable this function please set to Enabled Please note that enabling this function may reduce CPU voltage and memory frequency and lead to system stability or compatibility issues with some memory modules or power supplies Please set this item to Disabled if the issues mentioned above occurs Cool n Quiet Enabled SVM Mode When this is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities provided by AMD V The default value is Enabled Configuration options Enabled and Disabled Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 29 NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 3 2 North Bridge Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Onboard HDMI HD Audio This allows you to enable or disable the Onboard HDMI HD Audio PanelType Selection IA bitie LVDS Output Port For models with the LVDS port This allows you to enable or disable the Onboard LVDS HDMI Output Port For models with the HDMI port This allows you to enable or disable the Onboard HDMI Panel Type Selection Use this to select a panel type Primary Graphics Adapter This will switch the PCI Bus scanning order while searching for a video card It allows you to select the type of Primary VGA in case of multiple video controllers The default value is PCI Ex
30. ity Copyright C 2011 American Megatrends Inc Save Changes and Exit Copyright 2011 NEXCOM International Co Ltd All Rights Reserved Save Changes and Exit When you select this option the following message Save configuration changes and exit setup will pop out Select OK to save changes and exit the UEFI SETUP Utility Discard Changes and Exit When you select this option the following message Discard changes and exit setup will pop out Select OK to exit the UEFI SETUP Utility without saving any changes Discard Changes When you select this option the following message Discard changes will pop out Select OK to discard all changes Load UEFI Defaults Load UEFI default values for all options The F9 key can be used for this operation NEX 611 User Manual
31. lobal Service Contact Information neresen 3 1 INTOUCH N ertet vo EU we etie E t UBI HR 26 Package Con SA Aa AA nan AN rta xiii SEE Men AE De DER A Aa 26 3 1 2 North Bridge Configuration an an A ii 27 3 2 sine 27 Chapter 1 Introduction 3 3 Advanced Screen 28 11 Package Contarle bd 1 3 3 1 CPU Cagaran KA Aha aii 29 1 2 Specifications eiit A 1 3 3 2 North Bridge Configuration siis 30 1 3 Unique aaa tee e Ero reden oed n Rud 3 31353 South Bridge Configurationi a aso od 31 1 4 Motherboard Layout Ss dn Aa A adan 4 3 3 4 Storage ConfigUtatiOn ue anna an aa noia 32 WSO T 6 3 3 5 Super IO Configuration tan decian dea 33 3 3 6 ACP Configuration i cedet e dede ardet 34 NEXCOM HE Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved ii NEX 611 User Manual Contents N e Oo M 3 3 7 USB Contigua 35 3 3 8 Trusted COMPUTING uice indc aeaii dans cod edd 36 3 4 Hardware Health Event Monitoring Screen a 38 BLD BOOSTEE m 39 316 Secutity Sreem nosini epinar ERR ERR UO er Re ER aca Scenes 40 3 7 EXE SGEE Liebes bostes ditio edel Pto Pr elt hund 41 NEXCOM Ei Copyright 2011 NEXCOM International Co Ltd All Rights Reserved iii NEX 611 User Manual Preface PREFACE Copyright This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved No part of this manual may be reproduce
32. mponents NEVER place your motherboard directly on a carpet Also remember to use a grounded wrist strap or touch a safety grounded nee object before you handle the components scant E lt break 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any components place them on a grounded anti static pad or in the bag that comes with the components The DIMM only fits in one correct orientation It will cause per manent damage to the motherboard and the DIMM if you force 5 When placing screws to secure the motherboard to the chassis please the DIMM into the slot at incorrect orientation do not over tighten the screws Doing so may damage the mother board Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated NEXCOM T Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 7 NEX 611 User Manual Chapter 2 Installation 2 2 Expansion Slots PCI Express Slots There is 1 PCI Express slot and 1 mini PCI Express slot on this motherboard mini PCIE Slots mini PCIE1 is used for mini PCIE cards PCIE slots The x4 lane width PCIE1 PCIE 2 0 x4 slot is used for PCI Ex press expansion cards Installing an expansion card Step 1 Before installing an expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of
33. one at your own risk and ex pense We are not responsible for possible damage caused by overclocking DERE CAUTION 1 Due to the operating system s limitation the actual memory size of the reservation for system usage under Windows 32 bit operating systems may be less than 4GB Windows 64 bit operating systems have no such limitation 1 3 Unique Features NEXCOM Instant Flash NEXCOM Instant Flash is a BIOS flash utility embedded in Flash ROM This convenient BIOS update tool allows you to update system BIOS without en tering operating systems first like MS DOS or Windows With this utility you can press the lt F6 gt key during the POST or the lt F2 gt key to enter into the BIOS setup menu to access NEXCOM Instant Flash Just launch this tool and save the new BIOS file to your USB flash drive floppy disk or hard drive then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system NEXCOM Crashless BIOS NEXCOM Crashless BIOS allows users to update their BIOS without fear of failing If power loss occurs during the BIOS update process NEXCOM Crashless BIOS will automatically finish the BIOS update procedure af ter regaining power Please note that BIOS files need to be placed in the root directory of your USB disk Only USB2 0 ports support this feature Copyright
34. ons Read all instructions carefully Do not place the unit on an unstable surface cart or stand Follow all warnings and cautions in this manual When replacing parts ensure that your service technician uses parts specified by the manufacturer Avoid using the system near water in direct sunlight or near a heating device The load of the system unit does not solely rely for support from the rackmounts located on the sides Firm support from the bottom is highly necessary in order to provide balance stability The computer is provided with a battery powered real time clock circuit There is a danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufactur er Discard used batteries according to the manufacturer s instructions DERE Installation Recommendations Ensure you have a stable clean working environment Dust and dirt can get into components and cause a malfunction Use containers to keep small components separated Adequate lighting and proper tools can prevent you from accidentally damaging the internal components Most of the procedures that follow require only a few simple tools including the following e A Philips screwdriver e A flat tipped screwdriver e A grounding strap e An anti static pad Using your fingers can disconnect most of the connections It is recom mended that you do not use needlenose pliers to disconnect
35. onsists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly The white wires are negative Connect to or GND pins while the colored ones are positive System Panel Header 9 pin PANEL1 see p 10 No 20 GND GND RESET PWRBTN GND PLED HDLED PLED HDLED 1 Pin Signal Name Pin Signal Name 1 HDLED 2 HDLED 3 GND 4 RESET 1 5 GND 6 PLED 7i PLED 8 PWRBTN 9 GND na NEX 611 User Manual Chapter 2 Installation 2 6 Onboard Headers and Connectors place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard Onboard headers and connectors are NOT jumpers Do NOT USB 2 0 Headers USB 2 0 Headers 9 pin USB6_7 see p 10 No 29 9 pin USB8_9 see p 10 No 30 9 pin USB10_11 see p 10 No 31 USB_PWR B A USB_PWR USB12 see p 10 No 33 Besides six default USB 2 0 ports on the I O panel there are three USB 2 0 headers and one USB port on this motherboard Each USB 2 0 header can support two USB 2 0 ports Pin Signal Name Pin Signal Name 1 USB_PWR 2 A 3 A 4 GND 6 USB_PWR 7 B 8 B 9 GND 10 DUMMY Print Port Header 25 pin LPT1 see p 10
36. press Share Memory This allows you to configure share memory The default value is Auto Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 30 NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 3 3 South Bridge Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Onboard LAN 1 This allows you to enable or disable the Onboard LAN 1 Onboard HD Audio Auto Onboard LAN 2 This allows you to enable or disable the Onboard LAN 2 Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers Onboard HD Audio Select Auto Enabled or Disabled for the onboard HD Audio If you select Auto the onboard HD Audio will be disabled when a PCI Sound Card is plugged Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 31 NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 3 4 Storage Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc SATA IDE Combined Mode Use this to enable or disable SATA IDE combined mode SATA Controller s Enabled Hard Disk S M A R T Use this to enable or disable S M A R T Self Monitorin
37. priate safety standards including IEC 60825 NEXCOM Zh Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Preface Technical Support and Assistance 1 For the most updated information of NEXCOM products visit NEX COM s website at www nexcom com 2 For technical issues that require contacting our technical support team or sales representative please have the following information ready before calling Product name and serial number Detailed information of the peripheral devices Detailed information of the installed software operating system version application software etc Acomplete description of the problem The exact wordings of the error messages Warning 1 Handling the unit carry the unit with both hands and handle it with care 2 Maintenance to keep the unit clean use only approved cleaning prod ucts or clean with a dry cloth 3 CompactFlash Turn off the unit s power before inserting or removing a CompactFlash storage card DERE Conventions Used in this Manual Warning Information about certain situations which if not A observed can cause personal injury This will prevent injury to yourself when performing a task e Caution Information to avoid damaging components or losing data A Note Provides additional information to complete a task easily NEXCOM a Copyright O 2011 NEXCOM International Co Ltd All Rights Res
38. raphics Connectors Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 2 Rear Panel I O 1 x PS 2 Mouse Keyboard Port 1 x D Sub Port 2 x HDMI Ports Optional 2 x Serial Ports RS 232 422 485 6 x Ready to Use USB 2 0 Ports 2 x RJ 45 LAN Ports with LED ACT LINK LED and SPEED LED HD Audio Jacks Line Out MIC In 4 x SATA3 6 0 Gb s connectors support RAID RAID 0 RAID 1 RAID 5 and RAID 10 NCQ AHCI and Hot Plug Raid is not supported by AMD A50M 1 x IVDS header Optional 1 x CPU Fan connector 1 x 4 pin 3 x USB 2 0 headers support 6 USB 2 0 ports 1 x Vertical Type A USB EN NEX 611 User Manual Chapter 1 Introduction Supports A SMBIOS 2 3 1 SMBIOS 2 3 1 Support Support CD 32Mb AMI UEFI ee EE BIOS with GUI support Supports q_IXAAXAK AIM and Play BIOS Feature ACPI 1 1 A Wake Up Events Microsoft Windows 8 8 64 bit 7 7 64 bit VistaTM VistaTM 64 bit XP XP 64 bit compliant Certifications FCC CE WHQL For detailed product information please visit our website http www nexcom com Hardware Monitor WARNING Please realize that there is a certain risk involved with overclocking in cluding adjusting the setting in the BIOS applying Untied Overclocking Technology or using third party overclocking tools Overclocking may af fect your system s stability or even cause damage to the components and devices of your system It should be d
39. raphics cards are plugged to this motherboard 12V GND GND 1 5V Pin Signal Name Pin Signal Name 1 45V 2 GND 3 GND 4 12V Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved NEX 611 User Manual Chapter 2 Installation 2 5 Installing the System Panel Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables PWRBTN Power Switch Connect to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is in S1 S3 sleep state The LED is off when the system is in S4 sleep state or powered off S5 HDLED Hard Drive Activity LED Connect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data NEXCOM Copyright 2011 NEXCOM International Co Ltd All Rights Reserved The front panel design may differ by chassis A front panel module mainly c
40. rnational Co Ltd All Rights Reserved Legacy USB Support Use this to select legacy support for USB devices There are four configu ration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to the descriptions below for details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to be used under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility is sues it is recommended to select Disabled to enter the OS UEFI Setup Only USB devices are allowed to be used only under UEFI setup and Windows Linux OS NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 3 8 Trusted Computing Aptio Setup Utility Copyright C 2011 American Megatrends Inc TPM SUPPORT Disabled TPM Support Use this to enable or disable BIOS support for security devices The default is Disabled Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved 36 NEX 611 User Manual Chapter 3 Uefi Setup Utility N COM 3 4 Hardware Health Event Monitoring Screen This section allows you to monitor the status of the hardware on your CPU FAN1 Setting system including the parameters of the CPU temperature motherboard This allows you to set CPU FAN1 s speed Configuration options Full On temperature fan speed and
41. ssing the reset button on the system chassis You may also restart by turning the system off and then back on Because the UEFI software is constantly being updated the following UEFI setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen NEXCOM Copyright 2011 NEXCOM International Co Ltd All Rights Reserved 3 1 1 UEFI Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information Advanced H W Monitor To display current hardware status To set up the advanced UEFI features Boot To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the UEFI SETUP UTILITY Use lt gt key or lt gt key to choose among the selections on the menu bar and then press lt Enter gt to get into the sub screen You can also use the mouse to click your required item Eum NEX 611 User Manual Chapter 3 Uefi Setup Utility 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description Ha Moves cursor left or right to select Screens lt gt Moves cursor up or down to select items To change option for the selected items lt Enter gt To bring up the selected screen
42. stern Room 708 Block 210 Tairan Industry amp Trading Place Futian Area Shenzhen 518040 China Tel 86 755 833 7203 Fax 86 755 833 7213 Email sales nexcom cn www nexcom cn Wuhan Office 1 C1804 1805 Mingze Liwan No 519 South Luoshi Rd Hongshan District Wuhan 430070 China Tel 86 27 8722 7400 Fax 86 27 8722 7400 Email sales nexcom cn www nexcom cn NEXCOM e Copyright 2011 NEXCOM International Co Ltd All Rights Reserved X NEX 611 User Manual Preface Chengdu Office Chengdu Office 9EShuxiangxie Xuefu Garden No 12 Section 1 South Yihuan Rd Chengdu 610061 China Tel 86 28 8523 0186 Fax 86 28 8523 0186 Email sales nexcom cn www nexcom cn Europe France NEXCOM France La Grande Arche Paroi Nord 92044 Paris La D fense France Tel 33 0 1 40 90 33 35 Fax 33 0 1 40 90 31 01 Email sales fr nexcom eu www nexcom eu Germany NEXCOM GmbH LeopoldstraBe Business Centre LeopoldstraBe 244 80807 Munich Germany Tel 49 89 208039 278 Fax 49 89 208039 279 Email sales de nexcom eu www nexcom eu NEXCOM Copyright O 2011 NEXCOM International Co Ltd All Rights Reserved Italy NEXCOM ITALIA S r l Via Gaudenzio Ferrari 29 21047 Saronno VA Italia Tel 439 02 9628 0333 Fax 39 02 9286 9215 Email nexcomitalia nexcom eu www nexcomitalia it United Kingdom NEXCOM EUROPE 10 Vincent Avenue Crownhill Business Centre Milton Keynes Buckinghamshire MK8
43. t rating marked on the product All cautions and warnings on the equipment should be noted 16 17 DERE If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or electri Cal shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage Do not place heavy objects on the equipment The unit uses a three wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock Do not defeat the purpose of this pin If your outlet does not support this kind of plug contact your electrician to replace your obsolete outlet CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTER IES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS The computer is provided with CD drives that comply with the ap pro
44. uide NEXCOM NEX 611 Support CD 2 x Serial ATA SATA Data Cables 1 x Serial ATA SATA HDD Power Cables 1 x I O Panel Shield 1 2 Specifications Mini ITX Form Factor 6 7 inx 6 7 in 17 0 cmx 17 0 cm All Solid Capacitor design 100 Japan made high quality Conductive Polymer Capacitors ES Supports AMD Embedded G Series APU T56N T48E TAOE Platform Supports AMD Virtualization Technology AMD A50M A55E Controller Hub a Channel DDR3 memory technology 2x 204 pin DDR3 SO DIMM 2x 204 pin DDR3 SO DIMM slots T56N supports DDR3 1333 1066 MHz SDRAM T48E T40E o paa DDR3 1066 MHz SDRAM Max Max capacity of system memory 8GB see CAUTION 1 of system memory 8GB see CAUTION 1 foe foe Memory ua NEX 611 User Manual Chapter 1 Introduction AMD Radeon HD 6320 with T56N AMD Radeon HD 6250 with T48E T40E Supports Pixel Shader 5 0 DirectX 11 Max shared memory 256MB Three VGA Output options D Sub LVDS and HDMI Supports D Sub with max resolution up to 2560 x 1600 60Hz for T56N or 1920 x 1200 for T48E T40E Supports 2 CH 24bits LVDS with max resolution up to 1920x1200 60Hz Optional Supports HDMI 1 3a Technology with max resolution up to 1920x1200 60Hz Optional Audio 2 CH Audio Realtek ALC662 Audio Codec 2 x Gigabit LAN 10 100 1000 Mb s Realtek RTL8111E LAN x Mini PCI Express slot Half size Expansion 1x PCI Express 2 0 x4 slot PCIE1 x4 mode Slots 1 G
Download Pdf Manuals
Related Search