TDSO-090 User Guide - Teledyne Scientific & Imaging
Contents
1. notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 Configuring the TDSO TELEDYNE SCIENTIFIC COMPANY 4 After the selection windows the measurement window is shown Before any measurements can be taken it is necessary that the TDSO is configured and a connection is made The SETUP button will open the configuration window Bi so cui a TELEDYNE SCIENTIFIC fi mso Gui a TELEDYNE SCIENTIFIC TDSO CONTROL GUI Version 10 03 14 TELEDYNE SCIENTIFIC COMPANY www teledyne si com DATA WRITE FOLDER es FILE NAME S aaa SETUP TDSO 090 TDSO 090 EXIT SETUP IP ADDRESS 192 168 0 100 PATTERN LENGTH 127 NRZ THRESHOLD 20 80 SAMPLE SIZE 256 DATA RATE CONFIGURATION DATA RATE Gbps FILE INDEX CLOCK CONFIGURATION CLOCK SOURCE DATA RATE DIVIDER M a ADVANCED WANDER OFF l PTB oN CONNECT 2 SETUP button Will display the setup window 3 EXIT button Return to the measurements window 4 SETUP Option Block IP ADDRESS Input the IP address of the TDSO default is 192 168 0 100 PATTERN LENGTH Test pattern length for the test default is 127 PRBS7 NRZ THRESHOLD Range used for the rise fall measurements default is 20 80 SAMPLE SIZE Number of points for the sample size in 1 000s default is 64 Teledyne Scientific Company reserves the right to make changes2. to its product specifications at any time without Page 17 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIENTIFIC COMPANY 5 DATA RATE CONFIGURATION Option Block DATA RATE Incoming data stream speed in Gbps default is 10 3125 FILE INDEX Configuration file to be used for the internal TDSO clock setup default is 0 The File Index is used to configure the internal TDSO clock generation Each configuration used Data Rate Reference Clock needs a separated configuration file If the configuration file does not exists it is created the first time the specific configuration is run it will take a couple of minutes to generate the configuration file Multiple files can be generated hence the index It selects the desired configuration file If the index is 1 the TDSO will run with the last used configuration file All the pre set data rates in the DATA RATE drop down already have an index 0 configuration file installed The DATA RATE DIVIDER for the reference clock for those pre installed files is as follows e 1 25Gbps to 1 5Gbps 4 e 1 969Gbps to 6 25Gbps 16 e 8 5Gbps to 20Gbps 64 6 CLOCK CONFIGURATION Option Block CLOCK SOURCE Fixed in the TDSO 090 External DATA RATE DIVIDER The clock should be a fraction of the data rate default is 64 The ideal reference clock should be bet
3. workmanlike manner consistent with industry standards THESE EXPRESS WARRANTIES INCLUDING THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS INTENDED IN THE CASE OF GOODS OTHER THAN THOSE OF SELLER S OWN MANUFACTURE SELLER MAKES NO WARRATIES EXPRESS STATUTORY OR IMPLIED THESE EXPRESS WARRANTIES INCLUDING THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS INTENDED OR GIVEN IN THE CASE OF GOODS OTHER THAN THOSE OF SELLER S OWN MANUFACTURE SELLER MAKES NO WARRANTIES EXPRESS STATUTORY OR IMPLIED RETURN AUTHORIZATIONS Buyer s return of defective Goods to Seller is subject to Seller s then current return authorization procedures Buyer shall promptly notify Seller of any nonconformance or defects in Goods and provide Seller a reasonable opportunity to inspect such Goods Goods shall not be returned without Seller s prior authorization as evidenced by a Return Material Authorization RMA number issued by Seller Once a RMA number is obtained Buyer shall return Goods transportation and insurance prepaid in accordance with instructions issued by Seller Failure to follow Sellers return authorization procedures may result in lost Goods delays additional service restock
4. A0 0514 id p SCIENTIFIC COMPANY How to connect this instrument to the computer The TDSO has 2 connection ports USB and Fast Ethernet NOTE The Ethernet connection is used for the measurements applications and the USB connection is used only to configure the device IP Address Install Software from the USB Flash Memory Run Setup exe from the flash drive to install the software If the PC does not have Microsoft NET 3 5 install it It is included in the USB flash memory USB Driver Installation Power the device using the included AC adapter Connect the device to the PC using the USB cable When the PC tries to install the driver manually select the driver location It is located in the USB Driver folder in the USB flash memory Configuring the IP address The TDSO comes pre configured with an IP address of 192 168 0 100 You can change the IP address by following the steps below e Power the device using the included AC adapter e Connect the device to the PC using the USB cable e Run DSO Config e The program will recognized the TDSO and will display its current configuration e Change the desired configuration and click the W button to configure the device e Exit the program and disconnect the USB cable NOTE The configuration values can also be refreshed by clicking on the status bar at the bottom of the DSO Config window Teledyne Scientific Company reserves the right to make changes to its produc
5. TDSO 090 USER GUIDE a TELEDYNE UG_0164PA0 0514 id p SCIENTIFIC COMPANY TDSO 090 User Guide Version 1 1 May 2014 Software Covered in this Version Windows GUI V1 3 Labview GUI V10 03 14 TSDO IP Configurator V1 0 Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 1 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 a TELEDYNE SCIENTIFIC COMPANY General Safety Summary Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it To avoid potential hazards use this product only as specified Only qualified personnel should perform service procedures While using this product you may need to access other parts of the system Read the General Safety Summary in other system manuals for warnings and cautions related to operating the system To Avoid Fire or Personal Injury Use Proper Power Cord Use only the power cord specified for this product and certified for the country of use Connect and Disconnect Properly Do not connect or disconnect probes or test leads while they are connected to a voltage source Observe All Terminal Ratings To avoid fire or shock hazard observe all ratings and markings on the product Consult the product manual for further ratings information before maki
6. TIFIC COMPANY Mask measurements window Here an eye mask is applied on the last captured eye diagram It is possible to choose a pre configured mask or create a custom mask The result is shown in the status bar at the bottom of the window a TELEDYNE es SCIENTIFIC amp IMAGING LLC Mask Settings Mask 10 GB Ethernet Mask Margin 0 C Find Max Margin Mask Uses X1 X4 Mask uses Y3 Y4 Mask uses X5 X6 Y5 Y6 V i mmmn 0 25 x4 0 75 Acquisition Finished 0 45 0 55 0 4 0 6 0 25 0 75 0 4 1 4 34 Eye Mask Mode selected 35 Mask Selection There are several pre configured masks or a custom mask can be selected 36 Apply Mask The result can be seen in the figure below were the mask is superimposed to the last eye diagram captured and the number of points failing is shown in the status bar Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 14 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE a TELEDYNE UG_0164PA0 0514 i p SCIENTIFIC COMPANY 37 Mask Margin Mask Margin Percentage This percentage is applied in the configured mask to increasing its size Find Mask Margin Finds how much the mask can be increased before it gets failing points 38 Custom Mask Options These sections config
7. anges to its product specifications at any time without notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use Page 10 of 22 TDSO 090 USER GUIDE TELEDYNE UG_0164PA0 0514 id p SCIENTIFIC COMPANY 12 Connect button Connect to TDSO and load the current configuration 13 Line Rate Incoming data stream speed in Gbps 14 Input Path Data input connection single ended or differential 15 Reference Clock Needs to be set to External for the TDSO 090 NOTE The CLK input is required for the TDSO operation The Data Input INP INN can be used in single ended or differential mode Using the TDSO in differential input mode will give better results 16 Number of Packets Number of points for the sample size in 1 000 per packet 17 Advance options Wander Confiscation PTB Internal Precision Time Base for clock generation Wander Wander Confiscation enables or disables the Time Base Wander Correction for a measurement Small variations in the TDSO internal reference time base appear as low frequency jitter wander in the acquired signal 18 NRZ Threshold Range used for the rise fall measurements 19 External Reference Clock Can be set as a frequency or a division of the data rate The ideal reference clock should be between 100MHz and 400MHz 20 Pattern Length Default is 127 bits PRBS 7 21 File Control Open or save configuration file Teledyn
8. e Scientific Company reserves the right to make changes to its product specifications at any time without Page 11 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 a TELEDYNE SCIENTIFIC COMPANY Taking Measurements Below is the main window where the eye measurement results are displayed TELEDYNE SCIENTIFIC amp IMAGING LLC 22 Eye Mode selected 23 Run Button 24 Run Control Options 25 Measurement Selection 26 Results Windows 27 Status Bar Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 12 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 a TELEDYNE SCIENTIFIC COMPANY Pattern measurements window a TELEDYNE SCIENTIFIC amp IMAGING LLC TDSO 0 ps 1043 28 Pattern Mode selected 29 Run Button 30 Run Control Options 31 Measurement Selection 32 Results Windows 33 Status Bar Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 13 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIEN
9. fic Company reserves the right to make changes to its product specifications at any time without Page 3 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE TELEDYNE a SCIENTIFIC COMPANY Package Contents The TDSO 090 box should contain the following The main instrument Micro USB cable Cross over Ethernet cable AC adapter USB flash memory holding the following Software Microsoft Net Framework TDSO Windows GUI TDSO Labview GUI TDSO USB driver TDSO IP configuration tool Windows API Oo 0 0 0 Figure 1 Package Content Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 4 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIENTIFIC COMPANY Minimum PC Requirements The minimum Windows PC properties for the TDSO application must meet the following specifications Windows XP SP3 or greater Minimum 1 GB RAM 1 Ethernet card to establish connection with the device 1 USB port for IP configuration Pentium 4 processor 2 0 GHz or greater NET Framework 3 5 sp1 NOTE Up to 32 TDSOs can be connect to one PC using the Windows GUI Labview GUI is limited to one connection Teledyne Scientific Com
10. ing charges warranty denial or refusal of a return shipment The RMA number must appear on the shipping label and all paperwork associated with the return Buyer shall identify the model or part number description and serial number if applicable for each of the Goods returned along with an explanation of the nonconformance or defect Issuance of a RMA number by Seller does not necessarily mean Seller agrees that returned Goods are defective or covered under warranty or that Goods will be repaired or replaced at no cost to Buyer If any Goods returned by Buyer are found to not be defective Buyer shall be so notified and such Goods shall be repaired replaced or returned to Buyer at Buyer s option and expense Such repair or replacement shall not be performed until and unless Buyer issues an Order to Seller authorizing such repair or replacement at Sellers then current repair or replacement price In addition Seller may charge Buyer for any testing or inspection costs In no event shall Seller retain or store returned Goods for more than six 6 months Goods repaired or replaced under warranty shall be returned to Buyer at Seller s expense Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 22 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use
11. ng connections to the product Do Not Operate With Covers or Panels Removed Avoid Exposed Circuitry Do not touch exposed connections and components when power is present Do Not Operate in Wet Damp Conditions Do Not Operate in an Explosive Atmosphere Keep Product Surfaces Clean and Dry Symbols and Terms in this manual These terms may appear in this manual Z CAUTION Identify conditions or practices that could result in damage to this product or other property Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 2 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIENTIFIC COMPANY Preface This is the user manual for the instrument It covers the following information e Describes how to install its software e Explains how to operate the instrument how to control acquisition of processing of and input output of information e Lists the specifications of the instrument About This Manual This manual is composed of the following chapters e Getting Started shows you the how to configure and install your instrument e Operating Basics providing the required procedure to operate the instrument including the software user interface e Description for all the performed measurements e Electrical Specifications Teledyne Scienti
12. onstruct the waveform 17 Waveform Display Values Shows the vertical and horizontal scales Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 20 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE a TELEDYNE UG_0164PA0 0514 id p SCIENTIFIC COMPANY Specifications Parameter Symbol Conditions Min Typ Max Units Input Bandwidth 25GHz GHz N Input Amplitude Single Ended 1 0Vpp V Input Rise Time and Fall Time 20 to ter tet lt 20 ps 80 Vertical Resolution 12 bits Clock Input Range 50 710 MHz Clock Input Amplitude 0 25 1 5 VPP Input Impedance Z 50 Q Intrinsic Jitter 1pS rms Amplitude Error rms 5 MV ms Data Format supported NRZ PRBS Pattern Capture PN11 Power Requirements Parameter Symbol Conditions Min Typ Max Units External 5V supply PWR External 1 5 A Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 21 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 a TELEDYNE SCIENTIFIC COMPANY Warranty LIMITED WARRANTY Seller warrants that the all work will be performed in a professional and
13. pany reserves the right to make changes to its product specifications at any time without Page 5 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE TELEDYNE UG_0164PA0 0514 id p SCIENTIFIC COMPANY Installation This chapter covers installation of the instrument addressing the following topics e Quick Start e How to connect the instrument and installing the USB driver e Configuring the IP address Quick Start To use the TDSO under Windows XP Windows 7 and Vista it is important that the correct sequence is followed e Make sure you have the Microsoft NET Framework 3 5 If not it is included in the USB flash memory e install the Software from the USB flash memory The GUI and the Configurator are the minimum requirement e Power the device using the included AC adapter e Connect the device to the PC using the USB cable e Install the USB driver e Configure the IP address using DSOConfig exe e Connect the device to the network using the Ethernet cable the connection can be through a router switch or directly to a PC e Run TDSO GUI exe Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 6 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE a TELEDYNE UG_0164P
14. s 2 252 34mV 252 83mV p Vertical EYE SAVE DATA DIS 10ps div 56mV div 2 SETUP button Will display the setup window 10 Main Display Display the eye and pattern waveforms 11 Results Table Shows the measurements results Current values or statistical values 12 Results Table Selection Current or Statistical 13 RUN button Will start and stop the measurements 14 Sample Counter This is the number of samples to be used for the statistical measurements This reflects the way the Windows API operates There is a function call for the display waveform and a separated one for the data measurements When the COUNT value is 1 all the data is the same current max min average If a statistical measurement is needed COUNT value should be increased and the statistical table will reflect the results for those samples In this case the waveform only reflects the last sample taken Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 19 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIENTIFIC COMPANY 15 EYE PATTERN button Display the eye or pattern waveform 16 File Save Option Block SAVE Button to start and stop saving Works only when in RUN mode SCREEN Save a screen snapshot DATA Save the raw data Can be used to re c
15. t specifications at any time without Page 7 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE a TELEDYNE UG_0164PA0 0514 id p SCIENTIFIC COMPANY Running the GUI Windows This chapter covers how to configure and run the TDSO GUI application to capture data from the TDSO The application is a native windows application and uses NET 3 5 e Start e Configuring the TDSO e Taking measurements Start This is the first screen you see when TDSO GUI exe is run a TELEDYNE SCIENTIFIC amp IMAGING LLC 1 Mode Selection Eye Pattern Mask 2 Connect to TDSO 3 Main window 4 Results Window Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 8 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIENTIFIC COMPANY Configuration The TDSO needs to be configured and connected before it can be used When the configuration button is clicked a window opens where you can add configure and remove a TDSO i oa TELEDYNE SCIENTIFIC amp IMAGING LLC npea pa Bet EEE Acquisition Finished 5 Connect button 6 Add TDSO 7 Remove TDSO 8 Configure existing TDSO Teledyne Scientific Company reserves
16. the right to make changes to its product specifications at any time without Page 9 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIENTIFIC COMPANY When a TDSO is added or when the configuration button of an existing TDSO is clicked the configuration window appears 4 TELEDYNE oe SCIENTIFIC amp IMAGING LLC H 1050 0 Configuration On Connector Conlgutshon Nase Tos0 0 Data Condigusation Normal Operator Bypass Mode BD Line Rate GH F NAZ Theeshotdts FERGJE e gp Ingua Path Dittecential Hietorence Clock External External Flelerence Freq MHz 161 13201 S 127 2 Pattern Length Wander O Precision Tase Bare PTB 1DS0 090 Configuration lonnection Configuration Name TDSO 0 Hardware Simulation Data Configuration Normal Operation Bypass Mode 10 3125 Input Path Differential x Line Rate GHz Reference Clock External 127 Num Of Packets 128 C Wander Confiscation C Precision Time Base PTB Freq MHz 9 Name TDSO name up to 32 TDSOs can be connected simultaneously 10 IP Address Factory configured as 192 168 0 100 11 Recall configuration from the TDSO IP Address need to be entered before recall Teledyne Scientific Company reserves the right to make ch
17. ure the shape of the mask 39 Custom Mask Values When create a custom mask those values define the mask when a pre defined mask is selected those values are filled with the values for the mask selected TELEDYNE oe Oe SETTING amp imagine uc Eam or ts i Save Rowult Color Graded Auto Log Event Eye Amplitude T find Mask Margin for TDSO 0 is equal to 0 with 0 Failing Points TDSO 0 128K Sample Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 15 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 a TELEDYNE SCIENTIFIC COMPANY Running the GUI LabView This chapter covers how to configure and run the TDSO GUI application to capture data from the TDSO The application was written in LabView using the Windows API to control the device LabView 2011 is needed to run this GUI e Start e Configuring the TDSO e Taking measurements Start This is the first screen you see when TDSO GUI is run Here there is a selection of which TDSO is being used E mso cui oa TELEDYNE SCIENTIFIC MODEL TDSO 090 TDSO 050 1 TDSO Selection button TDSO 050 or TDSO 090 options Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 16 of 22
18. ween 100MHz and 400MHz NOTE The CLK input is required for the TDSO operation The Data Input INP INN can be used in single ended or differential mode Using the TDSO in differential input mode will give better results 7 ADVANCED Option Block WANDER Wander Confiscation default is OFF PTB Internal Precision Time Base for clock generation default is ON WANDER Wander Confiscation enables or disables the Time Base Wander Correction for a measurement Small variations in the TDSO internal reference time base appear as low frequency jitter wander in the acquired signal 8 CONNECT button Connect to TDSO and load the current configuration 9 DATA WRITE Option Block FOLDER Location of the folder where the data is to be saved FILE NAME File name to be used for the saved data Teledyne Scientific Company reserves the right to make changes to its product specifications at any time without Page 18 of 22 notice The information furnished herein is believed to be accurate however no responsibility is assumed for its use TDSO 090 USER GUIDE UG_0164PA0 0514 4 TELEDYNE SCIENTIFIC COMPANY Taking Measurements Below is the main window where the measurements results are displayed E mso cul aaea gAn TELEDYNE SCIENTIFIC TDSO 090 SETUP CURRENT EYE EyeHeight EyeOne EyeZero EyeAmpl EyeWidth EyeCross VALUE 419 30mV 229 00mV 228 33mV 457 33mV 44 97ps 50 20 WAVEFORM Jitter pp RT FT MAX MIN VALUE 03ps 20 98p
Download Pdf Manuals
Related Search