Wireless switch socket „FS20 ST“
Contents
1. 3 Explanation of icons A I The icon with a lightning flash in a triangle is used to alert you to potential personal injury hazards such as electric shock The icon with an exclamation mark in a triangle points to important instructions in this user manual that must be ob served The hand symbol indicates special tips and information on operation 4 Safety instructions A The product s guarantee becomes invalid if the product is damaged as a result of failure to observe these operating instructions We do not assume any liability for any result ing damages Nor do we assume liability for damage to property or personal injury caused by improper use or failure to ob serve the safety instructions In such cases the product s guarantee becomes invalid For safety and licensing CE reasons any unauthorised alterations to and or modification of the product are not permitted Donotuse this product in hospitals or medical institutions Although the product emits only relatively weak radio signals these may cause life support systems to malfunction This may also be the case in other areas The product is designed in accordance with protection class The only voltage source that may be used is that of the correct power socket outlet 230V 50Hz with the protective earth conductor of the public power supply system The product is not a toy and should be kept out of the reach of children Therefore2. interference in urban areas that reduces the signal to noise ratio the signal is no longer recognised due to this noise Interference radiation resulting from insufficiently shielded electronic devices for example operating computers or similar 17 18 Please note Do not place several wireless receivers for example switch sockets directly next to each other because they can nega tively affect each other range may be reduced Keep them separated by a distance of at least 20cm 15 Declaration of conformity DOC We Conrad Electronic Klaus Conrad Strake 1 D 92240 Hirschau Ger many hereby declare that this product complies with the fundamental requirements and other relevant regulations of directive 1999 5 EG You can find the declaration of conformity for this product at www conrad com 16 Technical specifications and features Power supply 230V 50Hz Power consumption approx 0 5W 3680W 230V 16A Programmable timer settings 1 second to 270min 4 hours 30min Breaking capacity Frequency 868 35MHz Modulation AM RANGE EEEE up to 100m free field Dimensions W x H x D 56mm x 134mm x 77mm Memory conservation also without power supply for instance during a power outage 19 http www conrad com 100 recycling paper Bleached without chlorine Imprint These operating instructions
3. use solvent based cleaning agents as these may damage the surface of the plastic casing and its inscription Afterwards allow the FS20 ST to dry completely before plugging it back into the power supply socket 13 Disposal When the product is no longer usable dispose of it in accord ance with the applicable statutory regulations 16 14 Information on the range The FS20 wireless control system including the FS20 ST works in the 868MHz range This range is also used by other devices and radio services Therefore devices that operate on the same or neighbouring frequency may restrict both the operation of the FS20 ST and its range The specified range of up to 100m is the so called free field range This describes the range when there is direct visual contact between the transmitter and the receiver In practice however walls ceilings etc between the transmitter and the receiver may affect and reduce the range Other causes of reduced ranges All types of high frequency interference Any buildings or vegetation Conductive metal parts that are located near the devices or within or near their transmission path for example radiators metallised insulation glass windows reinforced concrete ceilings etc Influence on the radiation pattern of antennas due to the distance from the transmitter or receiver to conductive surfaces or objects also to human bodies or the ground Broadband
4. OPERATING INSTRUCTIONS Version 08 07 ce Wireless switch socket F920 ST Item no 62 30 04 ONRAAD Introduction Dear customer Thank you for purchasing this product This product meets the requirements of both current national and European guidelines Please read the user manual completely and observe the safety and operation instructions before using the product ies This user manual belongs to this product It contains important information specific to its operation and handling Please bear this in mind when passing on the product to a third party Therefore keep this user manual for future reference All company and product names contained herein are trademarks of their respective owners All rights reserved For more inquiries contact or consult our technical service Germany Tel no 49 9604 40 88 80 Fax no 49 9604 40 88 48 e mail tkb conrad de Mon to Thur 8 00am to 4 30pm Fri 8 00am to 2 00pm Table of contents Page A Prescribed use Scope of delivery Explanation of icons Safety instructions Control panel Registering a FS20 transmitte Operation a Remote control operation b Controlling the FS20 device c Direct operation 8 Timer function a Programming the timer b Timer operation Starting the timer Prematurely stopping the timer Deactivating timer function Temporary switching to permanent Service uu 12 9 Integrating the wireless switch socket in
5. are published by Conrad Electronic SE Klaus Conrad Str 1 D 92240 Hirschau Germany No reproduction including translation is permitted in whole or part e g photocopy microfilming or storage in electronic data processing equipment without the express written consent of the publisher The operating instructions reflect the current technical specifications at time of print We reserve the right to change the technical or physical specifications Copyright 2006 by Conrad Electronic SE Printed in Germany
6. e wireless switch socket ies It should be possible to switch the load for example the lamp on and off by briefly pressing the button 1 on 2 off 3 on etc 6 Registering a FS20 transmitter To register the wireless switch socket FS20 ST with a FS20 transmitter for example a remote control from the FS20 wireless control system or other devices such as the load monitor FS20 FMS proceed as follows Press and hold the control button on the FS20 ST for at least 15 seconds The control indicator LED on the wireless switch socket starts to blink and the device is now in programming mode Alternatively the wireless switch socket can also be plugged into the socket with the control button already pressed This way the device switches immediately to programming mode control indicator LED blinks Briefly press a button of the desired key combination on your remote control or corresponding control button of a FS20 device for example load monitor FS20 FMS When the wireless switch socket receives the code the control indicator LED stops blinking The wireless switch socket is now programmed to this remote control or the corresponding FS20 device If required the programming can be replaced at any time by another button on the remote control or by another remote control channel To do this proceed again as described above Additional functions for example timer programming a
7. less switcl or o different ways h socket Briefly press for fewer than 0 4 seconds the left button of the assigned button combination on the remote control gt Deactivating timer function Press and hold the respective button combination on the remote control of your wireless switch socket simultaneously for one to five seconds 1 to 5 sec 11 The control indicator LED on the wireless switch socket blinks Now briefly press the control button on the wireless switch socket The timer programming mode is ended and the timer function is removed You can now use the wireless switch socket again in its normal manual operation mode gt Temporary switching to permanent service To override an automatic switch off by the timer function for the current timer setting for example a lamp should not be switched off after the timer setting expires proceed as follows Press the right button of the assigned button combination on your remote control for longer than 0 4 seconds or Alternatively press the control button connected to the wireless switch socket for longer than 0 4 seconds provided that the wireless switch is switched off Afterwards the wireless switch socket remains perma nently switched on The timer function is available again after the next manual switch off the wireless switch socket switches off as usual after the timer setting has expired 12 9 Integrating the wi
8. ons Strong magnetic fields such as those found near machines or loudspeak ers Never use the product immediately after it has been brought from a cold room into a warm one The condensation water generated could destroy the product Wait until the product has reached room temperature This can take several hours Do not handle the product with damp or wet hands This is true for all electrical devices The device must not be opened or taken apart There are no serviceable parts inside the product The licence CE and the guarantee warrantee becomes invalid if you open take apart the device Make sure that the insulation of the entire product is neither damaged nor destroyed Always check the product for damage before using it If you detect any damage do NOT connect the product to the supply voltage Life threatening danger 15 This product is not a toy and should be kept out of the reach of children Even a fall from a low height can damage the product 12 Maintenance and cleaning This product does not require maintenance Repairs or maintenance work may only be carried out by a skilled technician Before cleaning unplug the FS20 ST from the power supply Ay and remove any cables or devices that are currently attached to the FS20 ST Then clean the FS20 ST using a soft clean dry and lint free cloth To remove heavier dirt use a cloth which is slightly moistened with lukewarm water Never
9. r to the corresponding user manual It is possible to program the timer for the load monitor FS20 MS with its command menu the following section does not apply to the FS20 FMS a Programming the timer Simultaneously press and hold both buttons of the respective button combination on your FS20 remote control for one to five seconds 1 to 5 sec The control indicator LED on the wireless switch socket blinks The time measurement for the desired on time begins After the desired amount of time has expired press both buttons on the remote control again simultaneously for one to five seconds 1 to 5 sec The on time is now programmed 10 IJ Please note If the time measurement is not ended manually the timer programming mode will automatically be ended after 270 minutes 4 hours 30min The timer is then programmed for a on time of 270 minutes 4 hours 30min b Timer operation gt Starting the timer There are two different ways of doing this Briefly press for fewer than 0 4 seconds the coni wireless switch socket or Briefly press for fewer than 0 4 seconds the right but button combination on your remote control gt Prematurely stopping the timer rol button on the on of the assigned Naturally the wireless switch socket and connected consumer loads are able to be switched off manually at any time There are of doing this Briefly press the control button on the wire
10. re described later in this user manual 7 Operation a Remote control operation Switching on Briefly press the right button of the programmed button combination Switching off Briefly press the left button of the programmed button combination b Controlling the FS20 device The procedure varies depending upon the FS20 device Please refer to the user manual of the specific FS20 device For example the load monitor FS20 FMS Switching on Briefly press the control key on the FS20 FMS Switching off Briefly press the control key on the FS20 FMS c Direct operation Switching on Briefly press the control key on the wireless switch socket Switching off Briefly press the control key on the wireless switch socket IJ The switch alternates every time the control key is pressed toggle function When the wireless switch socket is switched on pressing the button will switch it off and vice versa 8 Timer function The wireless switch socket can also be used as a timer IJ As soon as a switching time has been programmed the FS20 ST remains switched on for the programmed length of time after each power on command After this time has expired it automatically switches off The timer is programmable for an on time of between 1 second and 270 minutes 4 hours 30 min IZ In order to program the timers you require a remote control from the FS20 wireless control system Please refe
11. reless switch socket into the FS20 address system The FS20 ST wireless switch socket can be integrated into the address system of the FS20 wireless control system via the latter s addressing scheme using single addresses function groups local and global masters More detailed information on exactly how this address system is structured is provided in the user manual of each transmitter belonging to the FS20 wireless control system a Assigning further addresses address types The wireless switch socket can assign up to four address types within the address system of the FS20 wireless control system This makes it possible for example to operate the wireless switch socket remotely from several transmitters with the same or different address types You can find more detailed information on the address system in the user manual of each remote control belonging to the FS20 wireless control system To assign several address types to the wireless switch socket repeat the programming steps described in section 6 You can create a list of up to four addresses or address types in the switch socket s memory b Deleting addresses or address types To delete a reception channel from the saved list proceed as follows Place the FS20 ST in programming mode as described in section 6 press and hold the control button on the FS20 ST for at least 15 seconds until the control indicator LED begins to blink 13 Now pres
12. s and hold for at least 0 4 seconds your remote control button that has been assigned to the reception channel that you wish to delete Afterwards the programming mode is automatically ended and the corresponding channel is deleted from the address list of the wireless switch socket 10 Resetting the default settings If necessary you can delete in one step all programs and settings that were previously saved in the wireless switch socket thus setting the switch socket back to its delivery state with all default settings To do so proceed as follows Press and hold the control button on the wireless switch socket for at least 15 seconds The control indicator LED on the wireless switch socket starts to blink and the device is now in programming mode Then release the button Briefly press the control button again Allassigned addresses and the timer mode with its programmed timer setting are now deleted or deactivated The control indicator LED goes out and the programming mode is ended The wireless switch socket no longer responds to any remote command and must be programmed again 14 11 Handling The product should only be used in dry indoor areas The following unfavourable conditions at the installation site during opera tion or transport are to be avoided Moisture or excessive air humidity Extreme cold or heat Direct sunligh Dust or flammable gases vapours or solvents Strong vibrati
13. take particular care when children are around Make sure the product does not become damp or wet it is only suitable for use in dry indoor locations not bathrooms or similar Otherwise here is the risk of a life threatening electric shock Protect the product against heat cold and direct sunlight while in storage or operation Never dismantle the product There is danger of a fatal electric shock Do not leave packaging material lying around This may become a dangerous plaything in the hands of children The accident prevention regulations established by the Employer s Liability Insurance Association for electrical equipment and facilities must be adhered to in commercial facilities Consult a skilled technician if you have doubts about the mode of operation safety or connection of the device Handle the product with care knocks blows or even a fall from a low height can damage it 5 Control panel D l N L fa ies Control keys with integrated LED X Socket for consumer loads 230V 50Hz max 16A On the back side there is a shock proof plug that must be plugged into a socket of the public power supply system 230V 50Hz Quick function test Plug the FS20 ST into a power socket with an earth connector operat ing voltage 230V 50Hz For example using a lamp as a load plug it into the socket on the front side of the wireless switch socket Briefly press the control button on th
14. to the FS20 address system a Assigning further addresses address types b Deleting addresses and address types 10 Resetting the default settings 11 Handling 12 Maintenance and cleaning 13 Disposal 14 Information on the range 15 Declaration of conformity DOC 16 Technical specifications and features csssecsseessseessneesseee 19 Se Or a i CODANaANA 1 Prescribed use The wirel less switch socket FS20 ST functions exclusively in conjunction with the FS20 wireless control system The wirel less control system can switch a device that is connected to the wireless switch socket on or off or dim the device without the use of cables refer to Another No part oi be opened echnical specifications and features eature is the integrated programmable timer function the product may be modified or adapted and the casing must not The safe y instructions and installation notes in this user manual must be observed without fail A Any use other than the one described above may damage the product and can also possibly create additional dangers for example short circuit fire electrical shock etc Read these operating instructions thoroughly and carefully as they contain a great deal of important information for the operation and handling 2 Scope of delivery Wireless switch socket FS20 ST User manual
Download Pdf Manuals
Related Search