Mobius 2-Bay RAID System
Contents
1. After completion reconnect via FW800 to access the formatted volume s 1 Specifications 2 Detailed View 10 Warranty Information 3 Inserting or Removing Drives 4 Setup This product includes a two 2 year repair replacement 5 RAID Modes warranty provided by Oyen Digital This warranty is non 6 Formatting transferable and is limited to the original purchaser Warranty service may be requested by completing the form at the 7 Sleep Mode following link www oyendigital com rma request form html 8 RAID 1 Rebuild se aes 9 Troubleshooting and FAQ For our complete warranty policy visit www oyendigital com warranty html 10 Warranty Information For more information visit our website at www oyendigital com 1 Specifications e 3 5 SATA VII HDD SSD Must be RAID qualified Check with mfg Supported Drives e eSATA e FireWire 800 USB 3 0 e RAID O Striping RAID Modes e RAID 1 Mirroring e JBOD e COMBINE l Windows XP 7 8 or higher R Operating Environment Temperature 5 C 40 C 8 25 x 4 5 x 5 0 inches Package Includes Mobius 2 Bay USB 3 0 cable FW800 cable eSATA cable power cord user guide key set Interface Ports 2 Detailed View oh JE fe JBOD n RAID 0 RAID 1 Move PN MZ 1 Door Latch 5 Power Button 1 1394b FW800 Ports 2 Door Lock 6 RAID Switch 2 USB 3 0 Po2. 7 Sleep Mode The Mobius 2 Bay does not have an auto sleep timer However it will follow the sleep settings of the computer When your computer enters sleep mode the drives inside the Mobius will spin down 8 RAID 1 Rebuild If one of the drives fail the drive s LED will change from BLUE to RED when connected to a computer A new HDD can be installed and will automatically rebuild with data if configured for RAID 1 Note The replacement drive must be a new unformatted drive with the same capacity as the original 1 Power down the Mobius 2 Remove the failed drive 3 Install the new drive and power up the Mobius 4 The LEDs will blink twice per second which indicates a rebuild in progress This can take several hours Mobius 2 Bay RAID System 9 Troubleshooting and FAQ User Guide 1 Does a Clear procedure delete data from existing RAID 1 or JBOD drive s No if a Clear procedure is performed on RAID 1 or JBOD drives the existing data on the drives will not be deleted 2 Can remove a drive from the RAID and install it in another enclosure for access to the files Yes only if using RAID 1 Mirroring or JBOD 3 The Mobius is connected to a Mac Yosemite computer via FW800 The Mobius appears in Disk Utility but am unable to format the drive s Why The issue may be caused by the Yosemite FireWire driver Please Table of Contents disconnect from FW800 and connect using USB to format the drive s
3. indows and Mac systems by formatting the drive as MS DOS FAT32 or exFAT Instructions are provided in the Mac OS link above If using RAID 0 we recommend performing a low level format after setting the RAID Please refer to the following http oyendigital com low level format
4. rt 3 Drive LEDs 7 Set Button 3 100 240VAC Power Input 4 Blue Power LED _ 8 Drive Bay 4 eSATA Port LED indicators State Drivel ED Drve216D HDD Sleep RAID 1 Rebuilding Slow blink twice per second Slow blink twice per second Note The Drive LEDs will be OFF when the Mobius is not connected to a computer 3 Inserting or Removing Drives Inserting Gently pull the lever and open the door Insert remove drive into bay To close pull the lever and push the door all the way closed Release the lever when the door is closed Locking Use the included key to lock the door if desired The default mode is JBOD To set a new mode perform these steps Set RAID Procedure 1 Set the switch on the Mobius to the desired mode 2 Connect the Mobius to the host computer 3 Press amp hold the MODE button while turning on the power 4 Continue holding the MODE button for 7 10 seconds 5 Release the MODE button The RAID mode is now configured If changing RAID modes you first must perform a Clear procedure to remove the previous RAID mode Clear Procedure 1 Set the switch on the Mobius to JBOD 2 Connect the Mobius to the host computer 3 Press the MODE button while turning on the power 4 Hold the MODE button for 7 10 seconds 5 Release the MODE button Any previous RAID mode is removed and the drives are now set for JBOD mode Set the RAID switch to the desired mode Pre
5. ss and hold MODE button and turn on the power 5 RAID Modes RAID 0 Striping is a non redundant data mapping technique It combines data evenly across both drives simultaneously dramatically increasing performance e RAID O will be viewed as one single storage unit If one disk in the RAID System fails all data in installed disks will be lost e The total capacity smallest drive x the total number of drives For example if the smallest drive is 500GB and the other is 2TB the total capacity will be 1TB 500 x 2 RAID 1 Mirroring consists of two drives storing duplicate copies of the same data In this mode the data is simultaneously written to two disks The speed of operation is slow in comparison to RAID 0 JBOD Clear is simply is a collection of drives that are recognized as separate drives by the OS JBOD provides no performance increase or redundancy This is the default setting Combine Span combines both hard drives into a single logical unit Unlike Striping it writes data to the first drive until it reaches full capacity When the first disk reaches full capacity data is written to the second disk Spanning does not increase performance or safety After setting a new RAID mode you must format the volume before it is accessible To format using Windows http oyendigital com windows reformat html To format using MAC OS http oyendigital com mac reformat html Note The drive can be used on both W
Download Pdf Manuals
Related Search