Manual - CYP Converters
Contents
1. 2 IN Input ports selection 1 4 3 OUT Output ports selection A D IR Cable Pin Assignment IR Blaster IR Extender 4 Power IR Blaster Signal NC IR Signal Power Grounding CONVERTERS TM CS RS 232 Pin Assignment Converter 15393 Remote Control PIN Assignment PIN Assignment I NC I NC 2 Tx 2 Rx 3 Rx 3 Tx 4 NC one 4 NC 5 GND Se 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Baud Rate 19200 bps Data Bit 8 bit Parity None Stop Bit 1 bit Flow Control None RS 232 and Telnet Commands Command Description help Dipslay all available commands Al A4 Switch Output A to 1 4 B1 B4 Switch Output B to 1 4 C1 C4 Switch Output C to 1 4 D1 D4 Switch Output D to 1 4 AB 1 AB 4 Switch Output ABCD to 1 4 at the same time SETIP lt IP gt lt SubNet gt lt GW gt Setting IP SubNet GateWay lt Static IP gt RSTIP IP configuration was reset to factory defaults lt DHCP gt IPCONFIG Display the current IP config PO Power Off P1 Power On STORE 01 04 Store current I O position 01 04 PRESET 01 04 Recall the store I O Position 01 04 CONVERITERS TV SHOW 01 04 Show current port s I O position 01 04 NAME NI N2 Name the stored port N1 01 04 no more than 8 charactors N2 ABCDEFGH I1 I4 Switch all the output to 1 4 ST Display the current matrix s2. input selection top Box with HDMI cable or DVI to HDMI cable 8 ALL IR OUT for it will blaster out all signal received from the IR IN at the Receiver sides 9 ALL IR IN signal to all Receiver s IR OUT 10 DC 24V oe a esse transmission of RS 232 commands to sections Telnet Control amp Web GUI Manufacturer use only signal transmission Connect to the IR extenders for IR signal reception Ensure that the remote Connect to the IR Blasters for IR signal transmission 7 HDMI IN 1 4 Connect to the IR Blaster for IR signal transmission to the source side Connect to the IR extender for IR signal reception Ensure that remote being Plug the 24 V DC power supply into the unit and connect the adaptor to an Deech Ad A mm Ad 2 IP amp ETHERNET Warning Please do not connect more than one active Ethernet link within 4 CAT5e 6 7 OUT A D Warning Please do not connect the CAT5e 6 7 cable into the Receiver s being used is within the direct line of sight of the IR extender for it will send Place the IR Blaster in direct line of sight of the equipment to be controlled Connect to the HDMI input source devices such as a DVD player or a Set Place the IR Blaster in direct line of sight of the equipment to be controlled used is within the direct line of sight of the IR extender for it will send out the AC outlet CONVERTERS TV Remote Control 1 POWER Press this button to switch on the device or set it to standby mode
3. If the IP is changed then the IP Address required for Telnet access will also change accordingly On a PC Laptop that is connected to the same active network as the Matrix open a web browser and type device s IP address on the web address entry bar The browser will display the device s status control and User setting pages Peer St tu uk rv RS TV Click on the Control tab to control power input output ports EDID and reset mode C 7 we CYPRESS Fasihi Ciapa Feed Prev Mac Sarg Mimi ees 4 S tz ENEH ere EDD Mede Ben React T ure ne Clicking on the User Setting tab allows you to reset the IP configuration The system will ask for a reboot of the device every time any of the settings are changed The IP address needed to access the WebGUI control will also need to be changed accordingly on the web address entry bar CYPRESS CGONVERTERS TV CS Specifications Video Bandwidth Input Ports Output Ports ESD Protection Power Supply Dimensions Weight Chassis Material Silkscreen Color Operating Temperature Storage Temperature Relative Humidity Power Consumption 340 MHz 10 2 Gbps 4xHDMI 5xIR Extender 1 lt RS 232 1xRJ 45 Control 1xMini USB Type B For firmware updated only 4xCATS5e 6 7 5xIR Blaster Human body Model 8kV Air gap discharge 4kV Contact discharge 24V 3 75A DC US EU standards CE FCC UL certified 436mm W x249mm D x44mm H Jac
4. 0 meters at 8 bit 12 bit resolution or 5 meters at 4K2K resolution Supports bi directional IR from input and output locations Supports RS 232 remote control on panel control and IP Control Telnet amp Web GUI 1U size design Supports external and internal EDID settings e Supports LPCM 7 1CH Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio transmission Note 1 Do not connect the LAN CONTROL port to CAT outputs of this device 2 Do not connect more than one Ethernet network link within the Matrix system doing so may tigger the device to shoot down 3 The PoC function is designed for powering compatible receiver units only non PoC receivers will need their own power supply Receivers of another brand may not be compatible CONVERTERS TV System Requirements Operation Controls and Functions e HDMI equipped source devices connect with HDMI cables or DVI equipped source connect with DVI to HDMI cables HDMI equipped displays TVs or monitors or HDMI equipped AV Receivers connect with HDMI cables Industry standard CAT5e 6 7 cables HDBaseT Receivers Front Panel rae CH IN i Hanne TE Ch a 00 Gage 1 LCM Displays the setting information of each input and output setting 2 IR IR Receiver window accepts the remote control signal of this device only 3 POWER Press this button to power the device on off The LED will illuminate green when th
5. HDBaseT 4x4 UHD HDMI over CATSe 6 7 Matrix with LAN Serving 15393 d Operation Manual EE Introduction Applications Features The 4K2K 4 by 4 HDMI Matrix over CAT5e 6 7 supports the transmission of video resolutions up to 4K2K Full HD multi channel digital audio and control via IR RS 232 Telnet or WebGUI from four high definition sources to four outputs over a single CAT5e 6 7 cable up to 100m for each output lt supports high resolution digital audio formats such as LPCM 7 1CH Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio as well as 3D content that can be displayed when connecting a 3D TV and 3D source Additionally the LAN connectivity will allow a 100BaseT network to be served to smart TVs or games consoles The Power over Cable PoC function can power compatible Receivers providing greater flexibility in installations e HDMI Matrix System Video TV wall display and control Security surveillance and control e Commercial advertising display and control e University lecture hall display and control e Retail sales and demonstration HDMI HDCP1 1 and DVI compliant e Supports HDMI 3D features e Supports resolutions VGA WUXGA and 4K2K 50 60 YUV_ 420 dependent upon the output display s EDID settings e Supports distances up to 100 meters through CAT5e 6 7 cables Supports 3D signal display dependent upon the output display EDID settings e Supports HDMI input output up to 1
6. To access the telnet control in Windows 7 click on the Start menu and type cmd in the Search field then press enter Under Windows XP go to the Start menu and click on Run type cmd with then press enter Under Mac OS X go to Go Applications Utilities Terminal cq VER TERS TV See below for reference i Remote Desktop Coninck B Skype Lira SR Windows Live Messenger Computer xy Meescht Eno SO d Lid Comin Fere She Accounts ail i amp ee i are ami Finer Select Startup Disk om Desktop MT Li Ficiure Motion Browser E Computer aC h Defaut Programa A Home tH KS Adobe Reader x Wi EJ Desktop FED Bp and upper EC N tenrk er D isk Wl Microsoft Word 2010 d e e j e Appii i Documents E Sticky Notes j gt Utilities Recent Folders en Wm st Meda Center H P Al Program Go t F lder Connect to Server cmd jp o ee SB VINE Once in the command line interface CLI type telnet then the IP address of the unit and 23 then hit enter Note The IP address of the Matrix can be displayed on the device s LCM monitor by pressing the Menu button twice Hicrocoft Windows Version 6 1 7680 Spy right cf Er Microsoft Lorporation gt cers CTP gt telnet 192 168 5 88 23 This will bring us into the device which we wish to control Type HELP to list the available commands gt CGONVERTERS TV Web GUI Control m Telnet 192 168 5 39 telnat g
7. e power is on red when it is in Standby mode 4 LOCK Press this button to lock all the buttons on the panel press again to unlock The LED will illuminate when locked 5 MENU Press this button to access the LCM menu system from here EDID settings can be managed and IP system settings are displayed 6 A D 1 4 and OUT IN Press the OUT or IN button to select the output or input mode and then press the required number button to make the selection accordingly For example if outputs A B need to be set to input 1 and outputs C D need to be set to input 2 then the following sequence of button presses need to be performed Press OUT A B N 1 MENU and then press OUT C DrIN 2 gt MENU Note If the MENU button is not pressed the selection will not be changed II CTIE EE CONVERTERS TV Rear Panel a 1 RS 232 Connect to a PC or control system with D Sub 9 pin cable for the This port is the link for Telnet or WebGUI controls connect to an active Ethernet link with an RJ45 terminated cable for further details please refer the Matrix system 3 SERVICE Connect from these CAT outputs to the CAT input port of the Receiver units with a single CAT5e 6 7 cable for HDMI Audio Video and IR RS 232 control LAN port 5 IR IN 1 4 out the IR signal to the selected Receiver s IR OUT 6 IR OUT 1 4 for it will blaster out the IR signal received from the Receiver side chosen by
8. ks Excluded 436 mm W x256 2 mm D x48 mm H Jacks Included 3352 Metal Black 0 C 40 C 32 F 104 F 20 C 60 C 4 F 140 F 20 90 RH non condensing 66W CONVERTERS TV Connection Diagram N R5 232 Equipped PC or Control System CAT5e 6 ms W i Cc
9. t T gt ALAA lt Switch Output A to 174 Hi Da switch Output H to 174 Di C4 z Switch Output C to 174 DL T fultch Output D to 174 ARCT e 17 83 UE Switch output ABCD to 174 at the sane time SETIP CIPA SubMet gt GW Setting IP Subdet GateYVaytStatic IPS RETIF IF Configuration Was Reset To Factory Defaults lt DHCP gt PCOHPIG Display the current IP config PH Power OFF el Power On STORE 81794 STORE current 170 position 8184 PRESET 8194 RECALL the store 70 position 917843 SHOW ALTRA SHOW current port s I 0 position SABA HARE Hi He HANE the stored port NILCRHI Mai no more than H charactors Hee HD DEER gt Ii I4 Switch all the output to 174 ST Display the current matrix state and firmware version AS System Reset to AT HZ GI D4 FA Setting EDID MODE 1 ST0 2 1 UARTBAUDL UARTEBAUDA Setting output T e uart baud 1 960Bbps 2 14488bps 3 1928 Bbhps 4 3840Gbps 5 5768Rbps 6 115288bps gt WARTS YE UARTSYH4 Swatch output s mart to AD UARITSHE I Swatch output s uart to MO WARTSWT Display the wart ewitching state T Display all available commands WIT Exit Type IPCONFIG To show all IP configurations To reset the IP type RSTIP and to use a set static IP type SETIP For a full list of commands see the Section on RS232 and Telnet Commands above Note Any commands will not be executed unless followed by a carriage return Commands are case insensitive
10. tate and firmware version RS System Reset to H4 EM Setting EDID MODE 1 STD 2 TV UARTBAUD1 4 Set output A D s uart baud rate from 1 6 1 9600bps 2 14400bps 3 19200bps 4 38400bps 5 5 600bps 6 115200bps UARTSW1 4 Switch output s UART to A D and allow Matrix to send commands to Receiver s connected RS 232 device UARTSWO Switch output s UART to MCU Restoring RS 232 control to the Receiver output back to Matrix UARTBAUD Display all the output s UART baud UARTSW Display the UART switching state Display all available commands QUIT Exit Telnet only Note Any commands will not be executed unless followed by a carriage return Commands are not case sensitive CONVERTERS TV Telnet Control RS 232 UART Command Illustration Diagram Note This Command allows ES 232 to control the Matrix Note This command allows R5 232 to control the R5 232 device connected to output A s Receiver Nofe This command allows RS 237 to control the R5 232 device connected fo output B s Receiver Note This command allows R5 232 to control the R 2327 device connected fo output C s Receiver Nofe This command allows ES 232 to control the R5 232 device connected fo output D s Receiver Before attempting to use the telnet control please ensure that both the Matrix via the LAN CONTROL port and the PC Laptop are connected to the active networks
Download Pdf Manuals
Related Search