NavMate Installation manual
Contents
1. Installation Manual J CAUTIONS Before installing the system please read the following cautions Failure to do so may result in damage to the system Controller 1 Do not interrupt power to the system while the software is updating This may result in corruption of the controller memory 2 Never drop the controller This may destroy the gyroscope or other components 3 The controller MUST be mounted horizontally Use a bubble level and a protractor to ensure the controller does not exceed 5 degrees from horizontal level 4 Mount the controller securely to ensure proper gyroscope function 5 Mount the controller away from other electronics which may interfere with the GPS receiver 6 Mount the controller away from strong magnetic fields Display unit 1 Never drop the display unit 2 Do not apply pressure to the display screen 3 Clean the display unit with a soft cotton cloth or lens tissue dampened with 70 isopropyl alcohol rubbing alcohol Any other cleaning fluids may damage the LCD screen CD ROM 1 Never drop the CD ROM 2 Never subject the CD ROM to a magnetic field 3 Use standard CD ROM cleaning procedures GPS ANTENNA 1 Mount the GPS antenna in a position that provides good satellite visibility 2 Mount the GPS antenna away from other electronics which may interfere with antenna reception 3 Do not cut pinch or sharply bend the GPS antenna cable WIRE HARNESS 1 Never connec2. Input pulse frequency 1 Hz to 200 Hz Input voltage range 13 to 26 Vmax Backup Lt Green 13 8V DC nominal when vehicle in reverse Backup light Low level voltage VL max 1 0 VL max High level voltage VH min 7 0 VH min SG SERERER 0000000 CONTROLLER CONNECTOR WIRE HARNESS VIEW Circuit Function Not used Not used Not used Not used Not used Not used Not used System power source battery plus Circuit Function Number Circuit Ground battery minus Number Circuit Reverse gear signal Ignition signal Vehicle speed signal sine wave Vehicle speed signal square wave Not used Not used Not used NavMate Navigation System Installation Manual 2 Route the video cable between the controller mounting location and the display mounting location NOTE Right angle connector mates to the controller Verify system starts and update software 1 Make sure ignition is OFF 2 Connect wire harness to controller and video cable to controller and display unit 3 Turn on ignition 4 Install the CD ROM into the controller NavMate will update its software DO NOT TURN OFF THE IGNITION WHILE NAVMATE IS UPDATING 5 Verify that NavMate powers up correctly Mount components and tuck cables 1 Controller mounting Mount the controller to the vehicle using the brackets provided The controller must be firmly attached
3. to the vehicle for the system to function properly Do not overtighten Do not mount the controller upside down The controller must be mounted level to within 5 degrees Use a bubble level and a protractor to verify Follow the rules under the CAUTIONS section on Pg 3 Using a utility knife slit the carpeting as necessary Use double sided tape to secure the brackets underneath the carpet The two L shaped mounting brackets may be reversed for mounting to the floor NOTE Upon removal of the controller reverse procedure and seal carpet slit with double sided tape 2 GPS antenna mounting The GPS antenna must be mounted in a place that provides good satellite visibility If a clear view cannot be obtained inside the vehicle due to a vertical windshield e g some delivery trucks the antenna may be mounted outside the vehicle Using double sided tape mount the GPS antenna to the instrument panel or package shelf Plug the antenna cable into the controller 3 Display Unit Mounting Mount the display unit using the vehicle specific bracket or flex mount Do not overtighten See www panavise com comm indash for details 4 Tuck all cables into the vehicle sill Make sure the cables are not pinched or sharply bent Setup Initialize and Calibrate GPS initialization allows the GPS receiver to find its current location The GPS must be initialized every time battery power is disconnected This process is quickened by using the system diagnostic
4. Installation Manual Note The URL on page two has changed to http www panavise com NavMate Navigation System OVERVIEW The NavMate Navigation System consists of the following components GPS Antenna Video Cable Wire Harness PLEASE VERIFY RECEIPT OF ALL COMPONENTS PRIOR TO ATTEMPTING TO INSTALL THE SYSTEM INTO A VEHICLE COMPONENT LOCATION FUNCTION PART NUMBER 1 Controller Mounts under a seat or in the trunk XU3F 18K931 AA 2 Controller brackets Mounts the controller to the vehicle XU3F 19A028 BA 3 Display unit Mounts to the instrument panel XU3F 10E889 AA 4 Display bracket Mounts the display unit to the instrument panel NA 5 GPS antenna Mounts on top of the instrument panel or package shelf XU3F 14B286 AA 6 Video cable Connects the controller and display unit XU3F 18B921 MA 7 Wire harness Connects the controller to the necessary vehicle signals XU3F 18B921 NA 8 CD ROM Contains the navigation software and map database various Not included with kit Vehicle specific InDash brackets and an adapter for the NavMate display unit may be ordered from Panavise Refer to www panavise com comm indash idbrand html for details Not included with kit The CD ROM for the appropriate geographic region must be ordered from Navigation Technologies Please call 1 888 NavMaps 628 6277 for questions or more information NavMatee Navigation System
5. menu 1 Move the vehicle outside to an area where the GPS antenna will have a clear view of the sky 2 Power up the system From the Please drive safely screen activate the diagnostic mode by pressing the following controls UP ARROW UP ARROW RIGHT ARROW MENU This must be done smoothly You will receive a notice that diagnostics are now activated under the Options Menu NavMatee Navigation System Installation Manual Press ENTER to advance to the Main Menu Press the OPT Options soft key 4 Select Preferences and set the Volume to level 4 Press ENTER 5 Select System Diagnostics from the Options Menu 6 Select GPS 7 Select GPS Initialization 8 Select Yes to confirm The GPS should initialize in 7 15 minutes You do not need to be present during this time Take this opportunity to fill out the warranty registration for the system and place the User Manual and CD ROM case in the vehicle glove compartment After initialization is complete the system will beep and return to the Diagnostic Menu 9 Drive the vehicle approximately 10 15 miles to allow the system to find its current location and calibrate for the speed signal pulse rate and the gyroscope Verify the VSS connection Make sure that the vehicle icon is moving 10 After a few miles of driving verify that the vehicle icon position is close to the actual vehicle position Make several turns and verify that the system recognize
6. s them 11 The system may now be returned to the customer Inform the customer that you have rough calibrated the system and that over the next 30 miles of driving the system will fine calibrate itself NavMatee Navigation System
7. square wave or a sine wave Use the green white or the yellow wire depending on VSS type See chart on Pg 5 Connect to a circuit which carries the signal that drives the odometer Special attention must be given to the vehicle speed sensor VSS connection For vehicles with a digital signal square wave TTL connecting to the green white striped wire will provide a proper signal In some vehicles e g certain Ford Lincoln Mercury the vehicle speed signal comes from a variable reluctance sensor which has a sine wave output Connecting to the yellow wire will provide a proper signal Some vehicles do not have a speed signal that is available to NavMate e g most vehicles built before 1982 and vehicles with speed signal carried on a bus NavMatee Navigation System Installation Manual Connect wires and route cables cont d Signal NavMate wire Requirements Typical location Battery Red 13 8 V DC nominal 3 Amp min Fuse block Ignition Pink 13 8V DC nominal when ignition on Fuse block Low level voltage VL max 1 0 VL max High level voltage VH min 7 0 VH min Ground Black battery minus Chassis VSS Grn Wht square wave square wave PCM Input pulse frequency OHZ to 2 5 kHz Input voltage range 13 to 26 Vmax Low level voltage VL max 0 9 VL max High level voltage VH min 4 0 VH min Yellow sine wave sine wave
8. t to any safety system circuits air bag seat belt etc 2 Disconnect the battery cable prior to making any connections NavMate Navigation System Installation Manual INSTALLATION Determine system layout 1 Determine the location to connect to the vehicle speed signal 2 Determine the location to connect to the remaining vehicle signals required by NavMate See chart on Pg 5 for signal requirements and NavMate wire colors 3 Determine general component layout e g where the controller will be mounted Connect wires and route cables 1 Connect wire harness to vehicle using splice piggyback method Using a multimeter verify the battery ignition ground and backup connections The NavMate system wire harness has five wires which must be connected to the vehicle See chart on Pg 5 for requirements Ground black Connect to a vehicle ground Maintain the shortest ground loop possible by connecting directly to a body ground point if available Ignition pink Connect to a circuit which is powered only with the key on run An example is the turn signal circuit Battery red Connect to a circuit which is powered constantly An example is the hazard signal circuit Reverse light green Connect to a circuit which is powered only when the vehicle is in reverse An example is the backup light Speed signal green white OR yellow The vehicle must have a vehicle speed signal VSS output in the form of a
Download Pdf Manuals
Related Search