Manual - Samsung CCTV
Contents
1. When the resistance value of copper wire is at 20 C 68 F Copper wire size AWG 4 24 0 22m 22 0 33m 20 0 52mf 18 0 83mf Resistance value 0 m 0 078 0 050 0 030 0 018 Voltage drop V m 0 028 0 018 0 011 0 006 Therefore having an excessively long distance between the power adaptor and the camera may affect the camera s performance X Standard voltage for camera operation DC 12V 10 AC 24V 10 X There may be some deviation in voltage drop depending on the type of wire and the manufacturer X The set for America does not include the power adapter Notes Please use a power adapter that meets the required standards Please connect the power after installation CONTROL CABLE RED TRX WHITE TRX Using RS 485 communication will enable you to control the OSD menu from a SAMSUNG TECHWIN System Controller or DVR 1 Connection to a PC Connect the camera to the PC via a RS 485 converter using RS 485 and a serial cable EX SERIAL PORT OF THE PC COM1 SERIAL CABLE RS 485 CONVERTER RS 485 CONTROL CABLE 2 Connection to a DVR or System Controller Connect the RS 485 cable to the connection ports of the DVR or System Controller 485 Control Board Connection Port RS 485 Control Port CONNECTION TERMINAL RED TRX CONNECTION TERMINAL WHITE TRX RS 485 Communication establishmen2. High Resolution 12X Vandal Dome Camera SVD 4700 User Guide Before installing and operating this product please read this manual thoroughly ENGLISH Thank you for purchasing a SAMSUNG CCD CAMERA Before operating the camera confirm the camera model and correct input power voltage In order to that you can understand this manual thoroughly we will introduce our model description E SVD 4700 SERIES NTSC MODEL PAL MODEL SVD 4700N SVD 4700P I MODEL DESCRIPTION SVD 4700X LL SIGNAL SYSTEM SIGNAL SYSTEM N NTSC MODEL P PAL MODEL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is A intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide
3. 2 Use the switch to change the SSDR level according to the contrast between bright and dark areas SSDR ON SSDR OFF Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by using the Function Setup switch so that the arrow indicates White Bal 2 Select a desired mode using the Function Setup switch p WHITE BRL X Select one of the following 5 modes as appropriate for your purpose QATW Select this when the color temperature is between 1 800 K and 10 500 K GO MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and then press the Function Setup switch CAWC SET To find the optimal luminance level for the current environment point the camera towards a sheet of white paper and press the Function Setup switch If the environment changes readjust it OUTDOOR Select this when the color temperature is between 1 700 K and 11 000 K sodium light inclusion CINDOOR Select this when the color temperature is between 4 500 K and 8 500 K C Notes White Balance may not work properly under the following conditions In this case select the AWC mode When the color temperature of the environment surrounding the subject is out of the control range e g clear sky or sunset When the ambient illumination of the subject is dim
4. 31 740 8145 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE CO LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungcctv com P No Z6806 1067 01B VAN 09 12
5. RETURN PRESET NOT DEFINED B EXPOSURE 1 Press the Function Setup Switch to access the main setup menu and then position the indicator over EXPOSURE by moving the up or down direction of the Function Setup Switch 2 Press the Function Setup Switch to confirm C BRIGHTNESS Use this feature to adjust image brightness Position the indicator over BRIGHTNESS by moving the up or down direction of the Function Setup Switch Then increase or decrease brightness level by moving the up or down direction of the Function Setup Switch while verifying the changes on screen Set END once desired level is obtained P BRIGHTHESS umf 56 IRIS Set IRIS to AUTO or MANUAL Position the indicator over IRIS by moving the up or down direction of the Function Setup Switch and then select the desired iris mode by moving the left or right direction of the Function Setup Switch gt IRIS AUTO AUTO The iris is automatically activated upon illumination MANUAL Man ual iris configuration Set IRIS to MANUAL by moving the left or right direction of the Function Setup Switch and then press the Function Setup Switch Increase or decrease iris level by moving the left or right direction of the Function Setup Switch while verifying the changes on screen IRIS AUTO SETUP IRIS MANUAL SETUP Y OPEN LIMIT iin 938 P IRIS F No FL 6 CLOSE LIMIT lum 1 IRIS MAN imm 1023 RETURN RETURN SHUTTER Control image brightness by
6. RS 485 Coaxial communication methods are supported RS 485 Communications STW SPD Pelco P Pelco D ra Il SEC AD BA gt d x Dye The camera s OSD is complimented by 12 foreign languages NTSC Korean English French Spanish Japanese Portuguese PAL English French German Spanish lesign the camera can be installed outside under building eaves or places that are exposed to the dust and rain Italian Chinese Russian Czech Polish Portuguese Samsung Techwin cares for the environment at all product manufacturing Stages to preserve the environment and is taking a number of steps to provide N7 customers with more environment friendly products The Eco mark represents eco Samsung Techwin s will to create environment friendly products and indicates RoHS compliant that the product satisfies the EU RoHS Directive Warnings amp Cautions This information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera The use of equipment such as an aerial ladder while providing after sales service shall be at your expense Separate the power plug during a thunder storm This product is only part of a surveillance system Therefore we can t compensate for material loss and or personal injuries by robbery f
7. gain value range 5dB 41dB OFF Disabled LOW Narrow range gain value adjustment MEDIUM MEDIUM range gain value adjustment E GAIN MANUAL SETUP bAGC VAL 5dB RETURN I SSNR Samsung Super Noise Reduction On screen noise reduction Position the indicator over SSNR3 by moving the up or down direction of the Function Setup Switch Set SSNR3 to the desired mode by moving the left or J right direction of the Function Setup Switch SSNR Di PLEVEL amm 12 OFF Disabled ER l Changing the AGC setting from LOW to HIGH results in greater sensitivity as well as on screen noise e Setting AGC to OFF locks SSNR3 configuration SENS UP This feature ensures clear images at night or under low light conditions Position the indicator over SENS UP by moving the up mpm or down direction of the Function Setup Switch SENS UP LIMIT SETUP Set SENS UP to the desired mode by moving the left IM pLinit x2 or right direction of the Function Setup Switch ee AUTO Select this mode for use in night time or under low light conditions OFF Disabled Once AUTO mode is set the user can configure the SENS UP limit by increasing decreasing the shutter speed e g X2 X4 X32 X64 X128 X256 X512 Enabling Sens Up increases camera sensitivity and may result in additional noise and or other phenomenons This is normal IE PA 1 Press the Function Setup Switch
8. mode by moving the up or down direction of the Function Setup Switch E H REV You can flip the picture horizontally on the IMAGE SETUP screen V REV You can flip the picture vertically on the screen SHARPNESS As you increase this value the picture NT outline becomes stronger and clearer SHARPNESS SETUP D gt LEVEL amn 16 C Monitor Please change the settings value of video appropriate to your monitor gt HOHTTOR CRT LCD Please select this menu item when using an LCD monitor CRT Please select this menu item when using a CRT monitor USER Please use this menu item when using a monitor other than standard ones You can change the gamma PED level and color gain in the sub menus LCD MONITOR SETUP gt GAMMA 0 45 PED LEVEL mpi 17 COLOR LEVEL mmm 50 CRT MONITOR SETUP P PED LEVEL miim 17 COLOR LEVEL iiim 50 USER MONITOR SETUP P GAMMA 0 55 PED LEVEL mmt 17 COLOR LEVEL 50 RETURN DISPLAY Us e this feature to designate a name for the camera which will display on the monitor screen P DISPLAY 00 CAMTITLE Press the Function Setup Switch to display the main setup menu and move the arrow indicator to CAM TITLE by moving the up or down direction of the Function Setup Switch Set CAM TITLE to ON by moving the left or right direction of the Function Setup Switch Notes e f the CAM TITLE feature is set to OFF the name will not displa
9. If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable OBACKIGIT OO 3 Select a desired mode using the Function Setup switch and press the Function Setup switch Unlike conventional cameras the SVD 4700 is designed to deliver a distinctive subject and POET BLC 16 adjust Ine dE UR SEE Enable thie user to change the leval background at the same time even when the subject is backlight by using the features of the enhanced then adjust th level mask tonis proprietary W V DSP chip E E 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Function Setup Switch so that the arrow indicates BACKLIGHT gt BACKLIGHT 2 Select a desired mode using the Function Setup OFF Not being used BLC Enables a user to directly select a desired area from a picture and to view the area more clearly HLC High Light Compensation If the scene contains extremely bright light areas such as from car headlight the light can mask out much of the on screen detail LEVEL Adjust level of the HLC function LOW MIDDLE HIGH MASK TONE Change the brightness LIMIT Enable to change the operating condition 3 Notes e For effective viewing of license plates there is a minimum required illumination and the shutter speed needs to be faster than 1 200sec Because there can b
10. Interlace Synchronization Internal Line Lock Frequency H 15 734 KHz V 59 94 Hz H 15 625 KHz V 50 00 Hz Color 580TV Lines Min B W 680TV Lines Min Min Illumination Color 0 2 Lux F1 6 50 IRE B W 0 004 Lux F1 6 50 IRE S N Y signal 52 dB AGC Off Weight ON Video Output CVBS 1 0Vp p 75Q Focus Auto Manual One push Zoom Movement Speed 1 9 sec Wide to Tele IRIS Control Auto Manual Lens Initialize Built In Camera Title OFF ON Displayed 15 characters Camera ID 255 ID Selectable Day amp Night Auto COLOR B W Gain Control LOW MEDIUM HIGH MANUAL OFF White Balance ATW AWC MANUAL INDOOR OUTDOOR 1 700k 11 000K Back Light Compensation SSDR BLC HLC OFF SHUTTER ESC FLK MANUAL 1 60 PAL 1 50 1 120K sec x2 x512 sec 0 S D English Spanish French Italian German Korean English Japanese Spanish Polish Russian Czech Chinese French Portuguese Taiwanese Portuguese Romanian Serbian Swedish Danish Turkish Motion Detection ON OFF output via communication Control output RS 485 2400 4800 9600 19200 38400 57600bps SSNR3 ON OFF 2D 3D Level adjustable Protocol STW PELCO D PELCO P BOSCH HONEYWELL VICON AD SEC PANASONIC SENSUP Auto Off Selec
11. SETUP and press the Function Setup Switch to confirm Increase or decrease optical zoom ZOOM or digital zoom D ZOOM positions eae pees by moving the directional key of Function EL Setup Switch while verifying the changes on screen Press the Function Setup Switch once the desired image quality is obtained MANUAL Select MANUAL and press the Function Setup a Switch to confirm Increase or decrease optical 1 Press the Function Setup Switch to access the main setup menu and then position the zoom ZOOM or digital zoom D ZOOM indicator over Focus moving the up or down direction of Function Setup Switch positions moving directional key of Function 2 Press the Function Setup Switch Setup Switch while verifying the changes on MODE You can select the most suitable zoom mode Move the arrow indicator to screen Press the Function Setup Switch until the MODE by moving the up or down direction of the Function Setup Switch ce desired image quality is obtained Focus can be manually adjusted independent of moving zoom ZOOM TRACK Select ON for the SMART ZOOM item in the MOTION DETECTION menu and press Function Setup Switch to change the settings for the SMART ZOOM function By moving the left or right direction of the Function Setup Switch in the ZOOM item to select AUTOTRACK or TRACK and press Function Setup Switch to activate the zoom action focus function AUTO TRACK Zooming in
12. T BACKLIGHT OFF BLC MOTION DET OFF ON FOCUS lt 1 MODE D 700M LENS INIT 700MTRACK ZOOM SPEED ZOOM POS INIT USER PRESET e RETURN EXPOSURE 4 BRIGHTNESS AGC RETURN IRIS SSNR SHUTTER SENS UP SPECIAL lt 1 PRIVACY SYNC MONITOR DAY NIGHT COMMAD DISPLAY DIS IMAGE ADJ RETURN Use the Function Setup switch within the camera Function Setup switch 1 Press the Function Setup switch Main setup menu is displayed on the monitor screen Select the function using gt ssDR OFF Change the status using the the Function Setup switch Function Setup switch 2 Select a desired function using the Function Setup switch Place the cursor over a desired item 3 Set up a selected item by using the Function Setup switch 4 To finish the setting select EXIT and press the Function Setup switch e An item with the icon also has sub menus To select a sub menu select an item with the icon and press the Function Setup switch An item with the icon is unavailable due to function settings SSDR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of images with high contrast between bright and dark spots gt 550R 1 When the SETUP menu screen is displayed select SSDR by using the switch so that the arrow indicates SSDR
13. adjusting shutter speed Position the indicator over SHUTTER by moving the up or down direction of the Function Setup Switch Then select the desired shutter mode A FLK ESC MANUAL by moving the up or down direction of the Function Setup Switch B SHUTTER MANUAL Manual shutter speed setting A FLK NTSC 1 100 PAL 1 120 Flicker free mode ESC Automatic shutter speed setting optimal Auto operation is possible only when the IRIS is set to MANUAL If you choose MANUAL select the optimal shutter __ J speed SHUTTER MANUAL SETUP In MANUAL mode the optimal shutter speed needs p SHUTTER VAL 1 50 to be designated Select from 1 60 to 1 120 000 Naba NTSC or from 1 50 to 1 120 000 PAL Sens Up mode can be configured manually 2x to 512x Verify changes made to the shutter speed by referencing to changes the on screen brightness Press the Function Setup Switch to complete Image may become unstable if the camera is set to ESC mode and faces a strong fluorescent light Under ESC mode the brightness can be adjusted by moving the left or right direction of the Function Setup Switch C AGC Auto Gain Control For brighter images Position the indicator over AGC by moving the up or down direction of the Function Setup Switch Set AGC to the desired mode by moving the left or right direction of the Function Setup Switch HIGH Wide range gain value adjustment MANUAL Selecting
14. ate device set the 750 Hi z properly The camera is not working properly and the surface of the camera is hot P Check that you have properly connected the camera to an appropriate power source The SENS UP function does not work Check that AGC of EXPOSURE SETUP menu is OFF gt Check that SHUTTER of EXPOSURE SETUP menu is A FLK or MANUAL The Motion Detection function does not work gt Check that MOTION DET of SPECIAL SETUP menu is OFF Color is not correct P Check the setting of WHITE BAL SETUP menu The screen flickers continually Check that direction of camera turns toward the Sun When coaxial communication is not available gt Make sure that the camera and monitor are installed within the recommended distance p Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded Input Voltage AC 24V 10 DC 12W 1090 Power Consumption MAX 4 0W ccd Imaging Device 4 inch Super HAD color CCD Total Pixels 811 H x 5080 795 H x 596 V Effective Pixels 768 H x 494 V 752 H x 5820 Optics 12X 123 94mm WIDE 46 05mm TELB F1 67 F1 88 Min Focus Distance 1 800mm TELE D ZOOM OFF ON Limit 16x Angle Field of view H Appr 51 54 Wide to 4 50 Tele V Appr 39 24 Wide to 3 38 Tele Scanning System 2 1
15. ay night switching delay gg 7 time from AUTO SETUP 5 7 10 15 20 30 40 60 sec gt DWELL TIME 7SEC DURATION You can select the day night switching DURATION sag RETURN point lux Color gt B W BMW gt Color BEND dU Fast 1 5 lux 2 0 lux Slow 0 7 lux 1 2 lux BURST LEVEL SETUP X When AGC is middle mode P BURST LEVEL inn 50 RETURN 4 1 BURST MODE SETUP gt BURST MODE ON RETURN 1 79 Notes When using a Video Auto Iris Lens if you set the lens level to low automatic switching between Color and Black amp White may not occur You cannot control the DAY NIGHT menu when AGC in the EXPOSURE menu is OFF At this time the exchange between DAY mode and NIGHT mode operates as like selecting COLOR mode The OSD key does not work for 3 seconds when switching to Color or B W to ensure stable camera operation The camera may focus less well under infrared illumination than under normal illumination Since the camera may not focus as well under infrared illumination at night as it does under normal illumination install an Extra low Dispersion Lens to obtain sharp pictures The brightness of illumination is changeable by installed environment k P DIS The DIS mode can compensate for vibration of the camera Notes e When DIS is operating D Z00M does not operate SYNC Two synchronization modes are available INTERNAL and EXTERNAL LINE LOCK I
16. e a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance When dark the HLC is only activated when a bright light exceeding a specific size In NIGHT ONLY mode The HLC is not activated in day light or when bright light is not present at night In NIGHT ONLY mode The HLC is not activated when the D ZOOM mode is ON or DIS mode is ON E This product has a feature that will detect movements of objects in 8 different areas on the screen The camera detects an object s movement by sensing disparity of outline brightness levels and color The camera sends a detection signal out via the MD output terminal and will zoom into a pre determined point B MOTION DET 1 Please press the Function Setup Switch OFF MOTION DETECTION mode is cancelled ON Any motion in the selected areas is observed AREA SEL You can select 8 different sensitivity MOTION DET area MOTION DET SENSTIVITY AREA AREA8 MIN MAX AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS XPOS YPOS You can control MD area size e SMART ZOOM Smart zoom is operated in connection g E with MOTION DETECTION When the SMART ZOOM SETUP SMART ZOOM function is ON while the jv szesz zoom MOTION DETECTION mode is ON the pant TIME zoom goes to the TARGET ZOOM positio
17. ews Adjust to the correct panning angle Then adjust the tilt angle by rotating the base Once complete re tighten the rotate base holding screws 1 Remove the dome cover and inner cover from the main body by loosening the three dome cover screws Notes s e When adjusting the rotating angle loosen rotate base holding screw as follows Figures Then tighten it again e When adjusting the tilting angle grip the tilt base and adjust tilting angle e When adjusting the panning angle loosen pan base holding screws as shown below and then re tighten Rotate Base Holding Screw Pan Base Holding Screw Rotate Base Holding Screw e When adjusting the tilt mechanism hold the Tilt base and NOT the lens Please connect the video output terminal located on the back of the camera to the monitor CCTV Camera The connection method varies depending on the type of monitor and accessories Please refer to the user s manual for each instrument Please turn off the power when connecting Please select Hi Z on the 750 Hi Z switch for the intermediate video TV set and select 750 for the Intermediate device as shown in the picture below Intermediate End monitor ka eope t7 The recommended adaptor specification for SVD 4700 is DC 12V 500mA AC24V a w WHITE TRX 500mA RED TRX Please check the standard power requirement before connecting the power
18. ire natural disaster or something like this type Warning Attention Special Mark Messages Ignoring this information may Ignoring this information may result in material loss and or E 5 PARES result in material loss and or a serious personal injuries including death slight injuries Indicates Never Allowed Indicates No Disassembling Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems mmm This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal COLOR DOME CAMERA 6 User Guide Q Precautions Do not install under extreme Do not install in high humidity temperature conditions enviro
19. is a highly durable component It features auto focus auto iris and zoom functions M Miscellaneous Functions SS A HLC High Light Compensation SENS UP FLIP H V REV D ZOOM SHARPNESS MOTION DETECTION and PRIVACY functions are provided hA bod ly f h esolution DYJA By adopting a diagonal 6mm 1 3 410 000 NTSC pixel 470 000 PAL pixel SONY CCD the camera produces clear picture quality with a horizontal resolution of 580 TV line in color and a horizontal olution of 680 TV line in BW mode 3 sung Super Noise Reduction e high performance W V DSP chip ctively removes low light gain noise an Panasonic ser Poneywel s h B 5 Coaxial Com ions ghosting to provide clear ages even in d 1 p environments y UN 3 FA Ds NI DIS Digital wen iC Ba vy y 5 Super Dynamic Range For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness phag DAYE NIGHT ICR Dyas This camera has a function that automatically selects the mode that is appropriate for daytime or night time conditions The COLOR mode operates in daytime conditions to provide optimum colors and BW mode operates in night time conditions to enhance the definition of the image imunication PENA
20. n LINE LOCK mode it synchronizes the camera s video out signal to the external SYNC signal p SYHC e INT Internal synchronization LL External line lock synchronization If you choose LL you can adjust the desired phase Press the SET button You can adjust the desired phase from 0 to 359 COMM AD Communication Adjustment This function sets up the camera communication status when controlling the camera through an external EO ESO sitim EA controlled device PAUD RATE Ei When the SPECIAL menu screen is displayed by REM CABLE moving the up or down direction of the Function Setup Switch so that the arrow indicates COMM ADJ Set up the mode moving the 4 direction of Function Setup Switch CAM ID Determines the camera s identification number between 0 and 255 Protocol Select the communication PROTOCOL STW PELCO D PELCO P BOSCH HONEYWELL VICON AD SEC PANASONIC BAUD RATE You can select 2400 4800 9600 1 9200 38400 57600 bps UART MODE You can select NONE EVEN or ODD for the parity bits RET PKT You can choose whether to send an ACK signal when the communication control command is issued to the camera IMAGE ADJ Includes image quality or special function factors B IMAGE ADJ When the SETUP menu screen is displayed select IMAGE ADJ by moving the up or down direction of the Function Setup Switch so that the arrow indicates IMAGE ADJ Select a desired
21. n once motion is detected Once the zoom action is finished and DWELL TIME has passed the zoom returns to the START ZOOM position START ZOOM By moving the left or right direction of the Function Setup Switch in the START ZOOM item to select the zoom position from 1x to 12x to be returned after the SMART ZOOM action is over TARGET ZOOM By moving the left or right direction of the Function Setup Switch in the TARGET ZOOM item to select the zoom position from 1x to 12x to be used during MOTION DETECTION DWELLTIME By moving the left or right direction of the Function Setup Switch in the DWELL TIME item to select a time between 5 and 60 seconds for the dwell time before the zoom is returned to the START ZOOM position 5 7 10 15 20 30 40 60 sec Tips on Using the Motion Detection Feature The feature may not function properly under flickering light conditions The camera interprets sudden changes in lighting and subsequent change in brightness of an object as motion With the feature enabled other algorithms may require additional time to operate This system does not guarantee prevention of fire or theft The manufacturer shall not be held responsible for any accident or damage incurred Connect an external alarm device to MD Out on back of the camera ONE PUSH Focus is automatically adjusted just once after E gd zoom position is changed Select ONE PUSH ZOOM FOCUS POS
22. nment e j A ae OK HIS Mh EA DX Go Use only under temperature conditions between May lower image quality 10 C and 50 C Provide good ventilation when using in high temperature conditions Do not install under unstable lighting conditions e NG Avoid touching the camera lens Severe lighting changes or flickering may The lens is the most important component hinder normal camera operation of the camera Be careful not to smear it with fingerprints Do not drop the camera or Never keep the camera face to subject it to physical shock strong light directly 4 y gt e n ag May cause a product malfunction May damage the CCD COLOR DOME CAMERA 7 User Guide Radioactivity exposure may damage the CCD Exposure to a spotlight or an object emitting strong light may cause smear or blooming Ensure that the power source complies with normal specifications before supplying it to the camera SVD 4700 USER Manual 95 Tapping Screw 4EA Quick Install Guide G Wrench Q Template DC12V 500mA Adaptor O Installation Video Output Cable X The set for America does not include the power adapter Pan Base Control panning angle of camera Rotate Base Control rotating angle of camera 12x Zoom Module Front Cover Pan Base Holding Screws Fix panned position 9 RS 485 Control Terminal The detailed decription refers to p14 Video Output Jack Video signals a
23. oves to the controlled ZOOM position when the power is truned on and the initial ZOOM position has been set p z M POS INIT e AUTO If you turn the power off and on the zoom ED 0 HH magnification level is set to the previous level that INIT ZOOM POS SETUP was set before the power went off gt POS INIT Xx MANUAL The zoom magnification level can be set from 1x EUM to 12X Notes The zoom postion is saved after 5 seconds when you set zoom function USER PRESET Preset user designated configurations using this feature Position the indicator over USER PRESET by moving the up or down direction of the Function Setup Switch and then set to ON by moving the left or right direction of the Function Setup Switch Press the Function Setup Switch to confirm p USER PRESET PRESET NO Up to 128 preset configuratons are supported SAVE Save configured preset CLEAR Clear configured preset RETURN Revert to the FOCUS SETUP menu C LENS INIT By moving the left or right direction of the Function Setup Switch in the Lens initialization item select Automatic or Manual and then press the SET button AUTO The lens can automatically be set by a pre selected day from 1 day to 7 days This will start from when the time is set Manual The Lens will reset when you press the Function Setup Switch gt LENS INIT MANUAL lt 4 USER PRESET D PRESET NO4 Tnm 1 SAVE CLEAR
24. re output through this port Connect this port to the Video IN port of a monitor Power Input Terminal Connect the power as specified for each model here Video Output terminal to Monitor Used for monitoring of video output when camera installation 9 Funtion Setup Switch Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item Dome Cover Inner Cover You can adjust camera to any direction by using the Pan Tilt Rotate mechanism Pan Base moves by 170 in each direction or 340 in total e Tilt Base covers 73 in each direction or 146 in total The installation should be done by qualified service personnel or system installers js angle range a a atate base E the sane as thatotthe Fan Pese Bone e ff the ceiling material is not strong enough to hold the installation screws the camera direction range is 195 and another is 145 may fall off Reinforce the ceiling as needed Methods of adjustment Take care not to drop the product during installation Do not allow anyone to stand Wall installation below the installation area After mounting the camera to the wall loosen the rotate base holding screws Adjust to the correct panning angle Then adjust the tilt angle by rotating the base Once complete re tighten the rotate base holding screws e Ceiling installation After mounting the camera to the ceiling loosen the rotate base holding scr
25. re to display the current zoom magnification level on screen Position the indicator over ZOOM MAG by moving the up or down direction of the Function Setup Switch Then set to ON by moving the left or right direction of the Function Setup Switch FONT COLOR You can select the font color white yellow green red blue LANGUAGE You can select the menu language according to your requirements Korean ESPANOL FRANCAIS ITALIANO DEUTSCH ENGLISH Japanese Chinese RUSSIAN CESKY POLSKI PORTUGUESE Taiwanese Romanian Serbian Swedish Danish Turkish END Select this to save the SPECIAL menu settings and return to the SPECIAL menu To reset your camera to factory default condition To finish setup menu If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician Nothing appears on the screen P Check that the power cord and line connection between the camera and monitor are fixed properly P Check that you have properly connected VIDEO cable to the camera VIDEO output jack The image on the screen is dim gt Is lens stained with dirt Clean your lens with soft clean cloth Set the monitor to proper condition gt If the camera is exposed to too strong light change the camera position The image on the screen is dark gt Adjust the contrast feature of the monitor gt If you have an intermedi
26. reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment CAUTION To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes o Features IMPR Warnings amp Cautions Precautions Components and Accessories Overview Installation E Installation E Adjust the panning tilting and rotate mechanism while checking the position on the monitor e Connection E Connecting To Monitor E Connecting To Power E RS 485 communication control E Using Coaxial Communications Operating Your Camera E Menu Configuration E Menu Setup EXPOSURE SPECIAL 1 ee vig Vi Ad ME 2X Optical Zoom Paga The built in SVD 4700 optical zoom lens
27. t initial value Item Camera ID BAUD RATE UART MODE RET PKT Initial value 1 9600 8 NONE 1 ENABLE When building a control system to control the camera please use to the STW SPD PROTOCOL or PELCO P PELCO D VICON AD PANASONIC BOSCH HONEYWELL SEC PROTOCOL When you connecting to RS 485 control cable please peel off the outer skin inside the RS 485 control cable eIn case of SCC 101 connection change communication mode to 8 E 1 at Communication configuration menu For more information refer to SCC 101 manual Coaxial Communications System OSD Control method DW CONTR MENU ENTER OSD KEY UP KEY JOYSTICK UP DOWN KEY JOYSTICK DOWN LEFT KEY JOYSTICK LEFT RIGHT KEY JOYSTICK RIGHT e RS 485 Video Cable The camera s video output port is connected to the monitor with a BNC coaxial cable shown below If the distance between the camera and the monitor exceeds the recommended maximum please use an auxiliary video amp TIBI Distance Recommended Cable Specification 300m 3C2V RG 59 U 450m 5C2V RG 6 U 600m TC2V RG 11 U e If the camera is controlled through coaxial communication please use a video amp intended for coaxial communications Regular video amps do not transfer coaxial signals SSDR OFF WHITE BAL ATW 0UTDOOR MANUAL INDOOR AWC SE
28. table x2 x512 Privacy Function ON OFF 12 Areas MIRROR ON OFF PRESET Operating Temperature Humidity Water Resistance ON OFF 128 Point 10 C to 50 C 20 to 80 RH IP66 Dimension 0148 x 126 mm Weight 1 38Kg X The specification for this product may change without prior notice for product improvement DECLARATION OF CONFORMITY Application of Council Directive s 89 336 EEC Manufacturer s Name SAMSUNG TECHWIN CO LTD Manufacturer s Address SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 European Representative Name European Representative Address Equipment Type Environment CCTV Camera Model Name SVD 4700P Beginning Serial NO C10S7010007 Year of Manufacture 2009 10 22 Conformance to EN 50081 1 1992 EMC Directive 89 336 EEC and 92 31 EEC EN 50130 4 1996 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Legal Representative in Europe Signature FD Gu Signature Full Name BONJENG GU Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON KOREA Place Date 2009 10 22 Date SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon 1 dong Jungwon gu Seongnam si Gyeonggi do Korea 462 703 TEL 82 31 740 8151 8 FAX 82
29. to access the main setup menu and then position the indicator over SPECIAL by moving the up or down direction of the Function Setup Switch 2 Press the Function Setup Switch to confirm C PRIVACY Hide an area you want to hide on the screen P PRIVACY When the SPECIAL menu screen is displayed by moving the up or down direction of the Function Setup Switch so that the arrow indicates PRIVACY GREI TOP wb 39 BOTTOM nhu 79 im m Set up the mode using the 4 direction buttons AREA SEL You can select up to 12 MD areas AREA MODE Determines whether to use the area selected in the AREA SEL MASK COLOR Determine area color You can select Green Red Blue Black White Gray DAY NIGHT You can display pictures in color or black and white gt if tHIGHT AUTO When the SETUP menu screen is displayed select DAY NIGHT by moving the up or down direction of the Function Setup Switch so that the arrow indicates DAY NIGHT select a desired mode by moving the left or right direction of the Function Setup Switch according to the picture display you want AUTO The mode is switched to Color in a normal environment but switches to B W mode when ambient illumination is low To set up the switching time or speed for AUTO mode press the Function Setup Switch COLOR The picture is always displayed in color B W The picture is always displayed in black and white e DWELLTIME You can select td
30. while deciding or adjusting the status of the focus TRACK The camera moves the focus track which is established OFF Only the zoom lens moves AUTO Select AUTO and press the Function Setup Switch to ii confirm Increase or decrease optical zoom ZOOM ZOOM POS SETUP or digital zoom D ZOOM positions by moving the up or down direction of the Function Setup Switch while verifying the changes on screen Enabling TE D Z00M ON means that digital zoom will activate once optical zoom ends The focus automatically adjusts when the lens zooms in and out Z00M SPEED Configure zoom tracing speed using this feature Position the indicator over ZOOM SPEED by moving the up or down direction of the Function Setup Switch and then set to desired mode by moving the left or right direction of the Function Setup Switch gt z h SPEED FAST FAST To move zoom fast SLOW To move zoom slowly MEDIUM To move zoom at medium speed D ZOOM Configure magnification limit from x2 x16 using this feature Position the indicator over D Z0OM by moving the up or down direction of the Function Setup Switch Set D ZOOM to ON and press the Function Setup Switch to confirm p 0 200 Set ZOOM LIMIT to the desired level by moving theleftor E qE right direction of the Function Setup Switch D ZOOM LIMIT SETUP uMIT x RETURN I Notes When the DIS is enabled you cannot use the D Z00M Z00M POS INIT M
31. yed in the monitor Press Function Setup Switch CAMERA TITLE SETUP ABCDEFGHIJKLM OPQRSTUVWXYZ abcdefghijkim AM THp e 0123456789 S gt CLR POS EN You can enter up to 15 characters a Move the cursor to the character entry field moving left or right direction of Function Setup Switch b Use the 4 direction of Function Setup Switch to select a desired character c Press the Function Setup Switch to confirm the selection of the blinking character The character is then saved and the cursor in the entry field moves to the next position d Repeat steps a through c until the desired name has been entered Correcting Mistakes Move the cursor th CLR and press the Function Setup Switch to clear the entire entry To modify one character use LEFT or RIGHT to position the cursor above the character to be modified and click the Function Setup Switch after selecting the character to enter Enter a title move the cursor to POS and press the Function Setup Switch The entered title appears on the screen Select the position to display the title on the screen by moving the 4 direction of Function Setup Switch and press the Function Setup Switch When the position is determined select CAM ID Displays camera ID on top left corner of the screen CAM INFO Displays camera information on screen MOTION ALARM You can toggle the use of the camera alarm ZOOM MAG Use th is featu
Download Pdf Manuals
Related Search