1. - Factory RV Surplus
Contents
1. TwinTuse U Bunp IT UBI TT 4000 Tetescopinc HitcH Rack System User Assembly and Operation Manual Gear Management Solutions Congratulations on your purchase of TwinTube UBI Whether you are using UBI with one of LGA s carriers or building your own platform the TwinTube UBI system is the best receiver hitch load carrying structure available The TwinTube UBI system features separate components that extend and enhance the load carrying capabilities of a receiver style hitch e The Spine assembly which provides UBI s structural strength and telescope support e The Frame assembly which provides UBI s carrier platform or box mounting interface and telescoping function e Safety Cable Quick Links allow the Frame and Spine system components to be separated thereby dividing the UBI s weight in half This provides ease of use when installing or removing and storing the system a aR wie F een Installation Tips e Keep this manual for future reference e The TwinTube UBI system fits a 2 size receiver style hitch and requires a minimum of a Class II tow rating If your vehicle has a Class II 1 25 size hitch an adapter may be used This may be purchased locally or contact LGA at 877 464 2376 regarding our Silent Flip Flop Shank accessory option e Keep in mind that the TwinTube is a precision built product and some consideration of2. LETSGOAERO Gear Management Solutions TwinTuse U Buio T UBI SILENT HircH Pin INSTALLATION Two Silent Hitch Pins are included with TwinTube UBI to prevent the inherent rattle that occurs when placing an accessory device in this case TwinTube UBI into the receiver hitch The installation process is the same for both Silent Hitch Pins the Hexhead Silent Hitch Pin J secures the TwinTube Assembly to the receiver hitch and the Hand Tighten Silent Hitch Pin K secures the Frame Assembly to the Spine Assembly WARNING The Silent Hitch Pins must be firmly tightened to work properly Make sure you use the Hexhead Silent Hitch Pin J to attach the Shank to the receiver hitch and use a wrench to securely tighten it 7 Orient the Shank A with the two 5 8 holes toward the receiver hitch on the vehicle Insert the spring nut from the Hexhead Silent Hitch Pin Assembly J into the Shank and line it up with the second hole from the end of the Shank A Use Second Hole unless more clear ance is required Note Use the bolt hole in the Shank that places the Twintube as close to your vehicle as possible lf more clearance is needed use the last hole in the Shank 2 Slide the Shank with the spring nut installed into the vehicle hitch and line up the Shank s bolt holes with the hole in the hitch Make sure the washer is on the Hexhead Silent Hitch Pin J and t
3. Nuts T 1 4 Washers S 7 3 Check that the Telescope Tubes D are as far toward the vehicle as possible and that the Telescope Pin holes in the rear of the Spine and Telescope Tubes D are aligned When everything is aligned tighten the 1 4x20 Locking Nuts T on the U Bolts H Tighten the 1 4x20 Locking Nuts alternating from side to side so each side of the Top Hat Bracket is equally compressed around the _ Telescope Tube D Use a 7 16 wrench to snug tighten the nuts to 12 ft Ibs Slide the Frame back and forth on the Spine to check the alignment If any binding is observed check to be sure that the Telescope Tubes D both come to rest against the Top Plate on the Spine and that the Wing is mounted squarely If not loosen the Top Hat Bracket fasteners and reposition the Wing F The Wings must fit squarely on the Telescope Tubes for the U Bolts to tighten correctly and for the telescope feature to operate freely Tighten the Top Hat Brackets so that the ears deflect into a slight bend Note i i 14 Repeat Steps 9 and 10 with the rear Wing F Leave the U Bolts H and Locking Nuts T loose enough so the Wing can move forward or back as needed to fit the bolt hole pattern of the platform you intend to mount on UBI You may adjust both Wings along the Frame tube as needed to accommodate your platform of choice as well as for additional clearance to accommodate spare tires etc
4. alignment is necessary when first assembling the system The TwinTube uses symmetry in a balanced manner so when bolting the system together for the first time tighten all hardware in a two step process first tighten the assembly to set the components in position and then when the TwinTube is installed securely tighten all hardware If this product was purchased from a dealer all documentation MUST be furnished to the customer aan enna mma meat samme TwinTuse U Buip iT UBI Parts IDENTIFICATION Parts List Item Description Ka CaO DO v2 AS Le TM OC os Shank V Plates Top Plate Telescope Tubes Fixed Tubes Wings 44 C Channel Top Hat Brackets 1 4 20 U Bolts Hexhead Silent Hitch Pin Assembly Hand Tighten Silent Hitch Pin Assembly Safety Cable with 2 Quicklink Connectors End Caps End Cap amp Reflector Assembly 1 2 Shoulder Bolts 1 2 Washers 1 2 Locking Nuts 1 4 Washers 1 4 Locking Nuts Safety Cable Retainer Center Plate 1 4 20 x 3 4 Bolts Slide Bumpers Paraffin Starter Wax Frame Assembly Quantity ah h N A HX NDANONNHY KH KH KPANNN AYN Rane Tools Needed 3 4 Wrench 3 4 Socket 1 4 Wrench or Socket 7 16 Wrench If you are missing any items contact your sales agent if the product was assembled by them If not or if purchased from Let s Go Aero please contact us at 1 877 GO 4 AERO 464 2376 Spine Assembly
5. hitch rack fits 2 size hitch receivers and is rated for a Class tow capability or higher Class Il IH and up When operating a tow accessory any item inserted into the hitch receiver you must comply with the vehicle and hitch receiver s towing parameters Consult your vehicle and hitch receiver owner manual s for details on your tow and tongue weight parameters Be sure that they are compatible with TwinTube UBI and your platform of choice s weight specifications Tongue Weight Compliance TwinTube UBI and any platform installed on this support structure creates a combined weight that creates direct down ward pressure on the hitch receiver s tongue This downward pressure is the tongue weight Tongue weight is one of the two critical weight rating factors of your tow rating s classification Class Il Ill IV V Never exceed your vehicle and hitch receiver s tongue weight specification TwinTube UBI Weight and Load Parameters TwinTube UBI weighs 48 lbs unloaded To determine your available load weight in accordance with your vehicle and hitch receivers tongue weight rating subtract TwinTube s 48 Ibs from your identified tongue weight rating The difference represents your vehicle and hitch receiver s available load weight TwinTube UBI is rated for up to 300 Ibs of carrying capacity This weight includes any platform installed on TwinTube UBI as well as the cargo itself When transporting cargo place hea
6. marring of the powder coated finish on the Telescope Tube D To install thread the Hand Tighten Silent Hitch Pin K into f 6 install the End Caps M without reflectors into the the spring nut that was installed in Step 6 Install ends of the Fixed Tubes D closest to the vehicle the pin clip from the assembly and the End Cap and Reflector Assemblies N into the ends of the Telescope Tubes at the rear Pin Clip ae Pink Bent of TwinTube farthest from vehicle for view from behind Nylon Bushing End Cap and Reflector Assemblies N WARNING The Hand Tighten Silent Hitch Pin MUST be firmly secured in Telescope Safety pin hole location before transit Failure to do so may result in potential hazards from improper operation including property damage and bodily injury WARNING Never move your vehicle with the TwinTube UBI ex tended in the telescoped position It must always be prop erly secured before transit Failure to do so may result in potential hazards from improper operation including property damage and bodily injury LETSGOAERO 6 Gear Management Solutions TwinTuse U Buro IT UBI SAFE Use amp OPERATION This information is pertinent to TwinTube UBI and any platform it supports including carriers by Let s Go Aero Be sure to follow these guidelines to prevent possible hazards from misuse Vehicle and Hitch Receiver Compliance This TwinTube UBI
7. on the back of your vehicle After installing your platform of choice to the Wings the last step is to firmly tighten all the 1 4x20 Nuts securing the Top Hat Brackets to the Wings Tighten these in a balanced fashion until securely snug Between uses periodically re check these fasteners for proper tightness 44 Wing F Top Hat Bracket G 1 4 Washers S and 1 4 Locking Nuts T _ Bracket G 1 4 Washers S and 1 4 Locking Nuts T LETSGOAERO Gear Management Solutions Twit U Buip iT UBI 1 5 Attach the Safety Cable L to the passenger side V Plate B and the Safety Cable Retainer U on the Frame using the Quick Links attached to the cable This will ensure that the Frame cannot slide off the Spine inadvertently To remove the Frame and carrier from the Spine simply undo one Quick Link This allows TwinTube to be separated into its two component parts to ease the installation removal and storage of the system Safety Cable L 1 f The Hand Tighten Silent Hitch Pin K with the handle is for securing TwinTube s Frame to the Spine during use When this pin is engaged it Passenger Side helps prevent carrier movement or wobble When in transit it prevents the Frame from sliding rearward on the Spine Be sure to use the 1 4 x 5 8 nylon Safety Cable bushing on the Silent Hitch Pin assembly to V Plate B Retainer U prevent any scratching or
8. wear You will find that TwinTube s Paraffin Wax is a great solution to clean hassle free operation Once applied it stays put and stays clean Fixed Tubes E Rub top sides and corners with Paraffin Wax FRAME ASSEMBLY 1 1 s Locate the Telescope Tubes D and orient them to the Spine Assembly with the weld seam down and with the hole away from the Spine The hole in each Telescope Tube D must line up with the hole in the Fixed Tube E Telescope Tubes D Gear Management Solutions Fania U Buip iT UBI 1 2 The two 44 Wings F form the mounting surface of the TwinTube UBI The Wings are adjustable for different platform widths but they must be at least 12 apart to support a load properly The first Wing F should be mounted as close to the Top Plate C of the Spine Assembly as possible depending on spare tires or ladders on the vehicle To mount this Wing place two 1 4x20 U Bolts H in the pre drilled mounting holes in the bottom of the Wing channel and position the Wing on the Telescope slide tubes Place the Safety Cable Retainer U on the passenger side and a Top Hat Bracket G over the U Bolt threads Secure the Brackets with a 1 4 Washer S and a 1 4 Locking Nut T on each leg of each Bracket WARNING The 44 Wings must be at least 12 apart to support a load properly and 1 4 Locking Nuts T Bracket G Safety Cable Retainer U 1 4 Locking
9. Wrench and a 3 4 Socket to position tighten the bolts Top Plate gt 1 2 Shoulder Bolts P haa i rsd at 1 2 Se i 4i Fixed Tubes E Se 1 2 Locking lt o2 2 gt Nuts R lt 1 1 2 Shoulder Bolts P 6 Securely tighten the bolts that attach the V Plates B to the Shank A Make sure that the bolts are so tight that itis difficult to tighten them further using hand tools Then snug tighten the bolts on the Center Plate to 12 ft Ibs fa Place a Slide Bumper X over each Fixed Tube and slide them back against the Top Plate 8 Insert the spring nut from Hand Tighten Silent Hitch Pin Assembly K into the Telescope Safety pin hole on one of the Fixed Tubes E Line up spring nut hole with the Telescope Safety Pin hole Note lt does not matter which Fixed Tube is used Either Fixed Tube may be used x Telescope Safety Pin Hole Spring Nut from Hand Tighten Silent Hitch Pin 1 2 Washers Q Oe 9 Securely tighten the bolts that attach the Fixed Tubes E to the V Plates A Make sure that the bolts are so tight that it is difficult to tighten them further using hand tools Periodically check that the bolts are tight to ensure TwinTube performs as designed 1 0 Rub the top sides and corners of the Spine s Fixed Tubes E with the enclosed bar of Paraffin Wax This reduces friction provides telescope smoothness and protects the powder coated paint from
10. hread it into the threaded spring nut Use a wrench to securely tighten the Hexhead Silent Hitch Pin J to 30 ft lbs 60 ft Ibs of torque equivalent to tightening a lug nut on a car wheel Install the pin clip from the assembly Pin Clip A Hexhead Silent Hitch Pin SPINE ASSEMBLY 3 The V Plate B with the Safety Cable hole goes on the passenger side of the Shank A Orient both V Plates B so that they angle up and away from the Shank A and the lower holes in the plates line up with the 1 2 holes in the Shank Install a 1 2 Shoulder Bolt P two 1 2 Washers Q and a 1 2 Locking Nut R in each hole Use a 3 4 Wrench and a 3 4 Socket to position tighten the bolts 1 2 Shoulder Bolts P Note V Plates MUST be attached angled AWAY from the vehicle for product to install properly 1 2 Washers Q 4 Place the Center Plate V between the V Plates Install a 1 4 20 x 3 4 Bolt two 2 1 4 Washers and a 1 4 Locking Nut in each hole Then tighten the bolts on the Center Plate 1 4 20 x By 1 4 3 4 Bolts al 1 4 Washers 1 4 20 x 3 4 Bolts 1 4 Locking Nuts LETSGOAERO Gear Management Solutions TwinTuse U Buro IT UBI 5 Place the Fixed Tubes E between the top of the V Plates B and place the Top Plate C on top Install a 1 2 Shoulder Bolt P two 1 2 Washers Q anda 1 2 Locking Nut R in each hole 2 per Tube Use a 3 4
11. nce from your vehicle as needed See Step 10 of this User Manual for Wing adjustment Verify that the Safety Cable is Secured The Safety Cable prevents the Frame from sliding off the Spine when telescoping the TwinTube It should always be engaged for this reason and to prevent the cable from dragging on the ground while in transit Never move your vehicle with the TwinTube UBI extended in the telescoped position The TwinTube UBI must always be properly secured before transit We warrant this product to the first consumer to be free from defect in material and workmanship for one year Please retain your sales slip for your records Any product or part thereof found to be defective within that period will be replaced without charge provided that 1 the product was not misused 2 no alterations Or modifications were made 3 its failure resulted from a defect in material or workmanship and not from normal wear expected in the use of the product 4 the product or part is delivered freight prepaid to Let s Go Aero Please contact Let s Go Aero toll free at 877 464 2376 to get a return authorization number prior to return Manufacturers only obligation shall be to replace such products or parts proved to be defective U S And International Patent Numbers 6 409 203 6 609 725 6 945 550 6 910 609 Patents Pendi mens _ LersGoAERO Gear Management Solutions
12. vy loads in the center and lighter cargo to the outside The 44 Wings must be at least 12 apart to support a load properly The rearward load length should not exceed the overall surface space provided by the TwinTube UBI structure The Wings are adjustable however always keep the load as close to the vehicle as possible Keep in mind that the further your load is from the hitch receiver the greater your downward pressure tongue weight For each one foot rearward approximately twenty percent of your hitch receiver s tongue weight is diminished Telescoping TwinTube UBI To telescope the TwinTube UBI remove the Hand Tighten Silent Hitch Pin from the Telescope Safety pin hole Verify that the Safety Cable is secured and then slide the frame to the rear WARNINGS Failure to adhere to these recommendations may result in potential hazards from improper operation includ ing property damage and bodily injury Engage Silent Hitch Pins Both pins MUST be securely engaged before transit A wrench MUST be used to tighten the Hexhead Silent Hitch Pin at the hitch receiver location Secure the TwinTube UBI as close to vehicle as possible Always secure TwinTube UBI as close to your vehicle as possible minimizing the distance of this structure and its load from your vehicle There are two bolt hole settings 5 3 4 and 8 positions from which to choose You may also adjust the Wings for up to 10 of rear installed cleara
Download Pdf Manuals
Related Search