CABLE MODEM USER MANUAL
Contents
1. Cautionary Instructions on Spray Adhesive can 3 B Press FlatWire to path with smoothing tools If painting 3 Plug in wire and attach 2nd wall box to 3 Attach wall box backplate to mounting surface mounting surface Pan Head Screw 3 E Connect patch cords amp test for signal 3 Disconnect amp remove system elements transfer Cover Wall Boxes with painter s tape A N Apply mesh tape over FlatWire do not overlap the mesh tape or cover with paint if painting only If painting then 1 1 I 1 1 1 l 1 1 1 1 1 I 4 Apply thin amp wide layers of concealing 4C Sand uneven or lumpy areas compound ae g77 tH HEE Bit it iH i H E anian 07 A D Apply additional layers of compound A E Sand until blended with surface ll SN A t I T for Paint amp Compound Please visit www FlatWireReady com for Tips to Cure amp Tricks as well as FAQs about the product i installation i7 Troubleshooting Tips amp Tricks Clean surfaces of dirt and loose particles Work in sections 8 feet or less when adhering FlatWire to surfaces Minimize folds as possible Spray adhesive into folds to avoid air bubbles Don t install FlatWire where you intend to hang pictures Run FlatWire adjacent to molding or trim Insert under chair rail as possible amp when FlatWire runs over chair rail do not use compound on2. CABLE MODEM USER MANUAL Thank you for buying FlatWire This high performance system enriches the audio and aesthetic guality of all environments FlatWire can be painted to greatly reduce the visibility of wire on your wall or completely hidden with mesh tape concealing compound mud amp paint Please read all instructions before initiating your installation Please visit www FlatWireReady com for additional products FAQs and technical assistance FlatWire Products Required for Installation S x10 or 20 feet of x1 Custom Patch Cord ws x1 DVD PWR Series 1 Terminator x1 1 foot Pair FlatWire 2 pieces x1 2 foot gt gt S f Gym x12 x2 x2 Wall Box Pan Head x1 Spray x1 Mesh Wall Box Backplate Screw Adhesive Tape x1 User Manual Tools for Installation Pencil Screwdriver Pliers Scissors Tape Measure Plastic Level Smoother Tools for Concealment Roller or Paintbrush Painter s Paint Compound Concealing Tape Knife Tray Compound Important Safety Instructions SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY IMPORTANT SAFETY INSTRUCTIONS gt _ Readallinstructions Donotinstall this surround sound system in a moist or wet location Hazards amp Warning For FlatWire Ready Spray Adhesive DANGER EXTREMELY FLAMMABLE LIQUID AND VAPOR VAPORS MAY CAUSE FLASH FIRES CONTENTS UNDER PRESSURE VAPORS HARMFUL CAUSES EYE IRRITATION HARMFUL OR FATAL IF SWALLO
3. OT breathe vapors Odor is not an adequate warning for hazardous conditions If you experience eye watering headache or dizziness or if air monitoring demonstrates vapor levels that are above applicable Ba _ _ FlatWire Ready Spray Adhesive Cautionary Information Continued limits wear an appropriate property fitted respirator during use and after application Follow respirator manufacturer s directions for respirator use DO NOT get in eyes on skin or clothing Wear appropriate gloves to prevent skin contact neoprene or nitrile Wear goggles or protective glasses with side shields Wash thoroughly after handling DO NOT use or store in direct sunlight DO NOT expose to heat or store at temperatures above 1209F Store away from stoves and radiators Exposure to heat or prolonged exposure to direct sunlight may cause bursting of the can DO NOT puncture or incinerate burn can Close container after use See Material Safety Data Sheet for additional information For a Material Safety Data Sheet contact your supplier or visit www flatwireready com FIRST AID EYE CONTACT Flush immediately with large amounts of water for at least 15 minutes and get medical attention immediately SKIN CONTACT Wash thoroughly with soap and water INHALATION If you experience difficulty breathing leave the area to obtain fresh air If continued difficulty is experienced get medical attention immediately INGESTION DO NOT INDUCE VOMITING Ca
4. WED KEEP OUT OF REACH OF CHILDREN DO NOT TAKE INTERNALLY VUVVV VY DANGER CONTAINS HEXANE 110 54 3 ACETONE 67 64 1 XYLENE 1330 20 7 METHYL ETHYL KETONE 78 93 3 PROPANE 74 98 6 AND ISOBUTANE 75 28 5 Causes eye skin nose throat and respiratory tract irritation Vapor harmful May affect the brain or nervous system causing dizziness headache nausea or unconsciousness Prolonged exposure to skin may cause dermatitis May be harmful if absorbed through the skin Prolonged vapor inhalation may result in severe physical injuries Hexane exposure can cause peripheral nerve damage to arms and legs which may be permanent May be toxic to blood liver kidneys and reproductive system PRECAUTIONARY MEASURES FOR USE HANDLING STORAGE AND DISPOSAL Vapors may ignite explosively Vapors may cause a flash fire Prevent buildup of vapors by providing fresh air such that chemical odors can not be detected during use and while drying Open all windows and doors Keep away from heat sparks and open flames DO NOT smoke Vapors may travel long distances to a source of ignition and flash back Extinguish all flames and pilot lights and turn off stoves heaters electric motors burners and other sources of ignition and static electricity Disconnect all appliances during use and until all vapors are gone Vapors are heavier than air and will collect in low areas Check all low areas basements sumps etc for vapor before entering DO N
5. ll physician immediately CALL 1 800 327 3874 IF IRRITATION OR COMPLICATIONS ARISE FROM ANY OF THE ABOVE ROUTES OF EXPOSURE U S and Canada CALL 1 800 535 5053 FOR CHEMICAL EMERGENCIES such as SPILLS LEAKS FIRE EXPOSURE OR ACCIDENT Installation Instructions 1 N Plan the location of your system elements and mark the path between the elements that the wire will follow 2 A Connect FlatWire TOP of Terminator 2 B Connect provided patch cord to Wall faces away from mounting surface Box and your components 2 Attach one wall box to mounting surface with 4 screws Pan Head 2 Attach wall box backplate to surface 2 Disconnect patch cords and non with 2 screws mounted wall box Pan Head Screw 2 The Terminator piece printed with 2 2 Click top amp bottom of 1 TOP must face away from the 4 Terminator gently together do NOT existing Terminator and sit below penetrate wire the wire Place the 2nd Terminator piece above the wire with tab pointing along wire towards the existing Terminator 2 3 Check that the wire pattern is aligned through the window of Terminator tab 3 Shake adhesive Spray adhesive to path for concealment with joint compound or spray FlatWire directly for concealment with paint Spray 8 or less at a time Wait 60 seconds If e If painting o ER N then N Follow Directions for Use amp
6. the chair rail only paint the FlatWire Avoid layering runs of FlatWire when possible Consider using textured paint Use a flexible plastic wallpaper smoothing tool for professional results vVvv VVVVVVY For Further Installation Tips amp Tricks or Helpful Suggestions call 1 888 FLATWIRE Before Returning this Product PLEASE CALL 1 888 FLATWIRE gt Southwire Southwire Company One Southwire Drive Carrollton Georgia 30119 www FlatWireReady com
Download Pdf Manuals
Related Search