USB Advisor T3 Quick Start - Digi-Key
Contents
1. aO TELEDYNE LECROY Visit digikey com Everywhereyoulook USB Advisor T3 Quick Start 1 Introduction The Teledyne LeCroy USB Advisor T3 USB 3 0 Protocol Analyzer is a verification system for USB development and testing It supports both USB 2 0 and USB 3 0 It is designed to record USB traffic and graphically present the logical transactions and events It connects to a host machine laptop or desktop PC via USB 2 0 TELEDYNE Advisor TS LECROY USB 2 0 3 0 Power Status Please see the Readme file on the installation CD for the latest information on PC requirements and supported operating systems The system can monitor traffic between USB 2 0 links using standard high speed compliant cables If configured for USB 3 0 testing the system supports monitoring between SuperSpeed links using USB 3 0 cables Components The Teledyne LeCroy Advisor T3 Analyzer package includes the following items e One Teledyne LeCroy USB Advisor T3 Analyzer e DC Power Adaptor e USB cables three e Installation CD ROM including documentation e Quick Start Guide e Carrying Case Please see the USB Protocol Suite User Manual on the installation CD for component specifications ay urn 4 Visit digikey com 3 Description ACAV le a TELEDYNE LECROY USB 2 0 3 0 j Power Status k The front panel has the following indicators and connectors Power LED green if on Status LED blue if system succe2. the information in this document without notice or penalty Copyright 2012 Teledyne LeCroy Inc All rights reserved Part Number 922852 00 Rev A 3 13 This document may be printed and reproduced without additional permission but all copies should contain this copyright notice
3. ct the USB port to a USB port on the host machine using the LONG 6 foot 2 meter USB 2 0 cable 3 Insert the Installation CD 4 Turn on the power switch At power on the Analyzer initializes itself in approximately ten seconds and performs an exhaustive self diagnostic that lasts about five seconds 5 Click Next after you see the Add New Hardware Wizard window 6 Follow the Microsoft Windows on screen Plug and Play instructions for the automatic installation of the Analyzer as a USB device on your host machine the required USB files are included on the Installation CD 7 Click Finish when you see the message that says Windows has finished installing the software that your new hardware requires and the driver files have been installed in your host machine 6 Starting the Application To start the application launch the Teledyne LeCroy USB Protocol Suite program from the Start Menu Start gt Programs gt LeCroy gt USB Protocol Suite gt USB Protocol Suite You can use the software with or without the system connected to the host machine Without the Analyzer the program functions as a trace viewer to view analyze and print trace files The first time you open the USB Protocol Suite application confirm proper installation by selecting About from the Help menu to view the Software Version Firmware Version BusEngine Version and Unit Serial Number Note When the Advisor T3 is power cycled it loses its Bus Engi
4. ne image The image updates automatically when the Application runs First USB Recording After installing and launching the software you can test the system by performing the following steps 1 Connect a USB cable to each of the two connectors on the Analyzer module then connect the other ends to the USB Device Under Test and USB Host Under Test 2 Select Recording Options under Setup on the Menu Bar 3 Select the General tab to display the following dialog box showing factory default settings such as Snapshot and 16 MB buffer size For the first recording you can leave these settings unchanged Under Recording Channels select 2 0 or 3 0 to record USB 2 0 or USB 3 0 traffic 4 Click OK to activate the recording options you selected 5 Turn on the USB devices that are to be tested and cause them to generate USB traffic Visit digikey com 6 Click Record on the Tool Bar The system starts to record the USB traffic immediately After 16 MB of traffic are recorded the Analyzer uploads the data and displays the packets in the trace window 7 To terminate recording before the snapshot automatically completes click m lon the Tool Bar When the recording session is finished the traffic is automatically uploaded from the Analyzer to the hard drive on your host machine as a file named data usb or the name you assigned as the default filename While the file is being uploaded you should see a brown progress bar at the bot
5. ssfully initializes red while booting If red for more than a minute hardware failure green while initializing Analyzer Port A downstream Connects to Device Under Test Analyzer Port B upstream Connects to Host Under Test Analyzer LEDs Rec Recording red if recording enabled Trig Trigger green if triggering 2 0 USB 2 0 yellow for Low and Full Speed green for Hi Speed 3 0 USB 3 0 green if link is up flashes green while data transfers yellow if polling The rear panel has the following indicators and connectors USB Type B connector for connection to host machine Sync Data Micro DB 25 25 pin external interface connector cable sold separately Power Connector 12V 3A DC Power Switch 0 1 Warning Do not open the enclosure No operator serviceable parts are inside Refer servicing to Teledyne LeCroy customer N care 4 Installing the Software Note You must install the software before connecting the Analyzer to the host machine for the first time 1 Insert the Installation CD into the CD drive on the host machine 2 Select Install Software from the Installation CD and follow the on screen installation instructions to install the application on the host machine s hard disk Visit digikey com 5 Setting Up the Analyzer To set up the Analyzer 1 Connect the AC power cable to the rear of the Analyzer and to a 100 volt to 240 volt 50 Hz to 60 Hz 100 W power outlet 2 Conne
6. tom of the screen When the bar disappears it indicates that the data has been uploaded to disk 8 To save a current recording for future reference select Save As under File on the Menu Bar OR click H on the Tool Bar to display the standard Save As screen Give the recording a unique name and save it to the appropriate directory For additional information on the results display see the USB Protocol Suite User Manual Teledyne LeCroy Customer Support Mail 3385 Scott Blvd Santa Clara CA 95054 3115 Web _ teledynelecroy com tm Library software PSG E mail psgsupport teledynelecroy com Tel 800 909 7112 USA and Canada Tel 408 653 1260 worldwide Fax 408 727 6622 worldwide Trademarks and Servicemarks Teledyne LeCroy USB Advisor T3 USB Protocol Suite CATC Trace and BusEngine are trademarks of Teledyne LeCroy Inc Microsoft and Windows are registered trademarks of Microsoft Inc All other trademarks are property of their respective companies Disclaimer Users are fully responsible for their application of any products The Software License and Limited Warranty for the accompanying product are set forth in information that shipped with the product and are incorporated herein by this reference If you are unable to locate the Software License or Limited Warranty contact Teledyne LeCroy for a copy Changes Product specifications are subject to change without notice Teledyne LeCroy reserves the right to revise
Download Pdf Manuals
Related Search