Interactive Instructions
Contents
1. O O O O Or oOo Install the TouchBeam module Attach to board Connect to projector PC Calibrate Note If the whiteboard is already installed please see page 36 12 Installing the mount Step 1 Attach the wall plate to the wall e For ease of installation mount the bracket on the wall using position 1 and mark other positions using a spirit level e Remove bracket and drill other positions e Use fixings suitable for your type of wall construction e Use all available fixing points e If in any doubt of the suitability of the wall it s construction or what type of fixings to use consult a qualified builder or installer Note Remove wall plate cover before attaching to wall Retain fixings for re attaching cover later 13 Step 2 Attach the projector to the mount plate y Place the projector on a soft clean surface Position the pre assembled mounting plate on top of the projector Insert 5xA M4 x 10mm screws from the fixing kit tighten with a posidrive screwdriver 14 Attach the projector to the mount Step 3 u D 5 5 Z Z 4 SE Lift the projector and mounting plate in to position Fig 3A Lift the projector so the two hooks slip over the protrusions on the black molding Fig 3B Position the washer C and teardrop shaped locking washer D against the hooks Fig 3C Insert bolt B M8 x 75mm and tighten it using the one of the allen keys provided Fig 3D2. default Touch Mode H for multi point touch Or switch to Pen Mode when using the light pen IR pen R Operation Mode Touch Area Setting Pen Mode F Calibration Auto v Touch Mode Touch Sensitivity 9 Ay Please note Windows XP and MAC operating systems only support single point touch 25 Step 5 TouchBeam Alignment 1 Press the button to switch to visible light mode The Red LED will blink continuously LED indicator Mode Blue LED Red LED Description IR Laser mode Solid IR laser ON Visible light mode Solid Blinking Visible light ON IR Laser OFF touch disabled Error Solid Error of LD module occurred 2 Connect PC and Projector via USB cable GI gt 3 Rotate the black and grey adjustment knobs clockwise until they stop 26 4 Rotate the grey knob counter clockwise until both beams are symmetrically at the same level 5 Rotate black knob counter clockwise move beams downwards until they hit whiteboard frame lt lt 6 Check the beam height with alignment the sticker for both left and right beams The beams should be located within the grey strip You will see a little red dot on the dark grey line Use the black and grey knobs to adjust the beams to locate them on the alignment sticker 27 7 Press the button again to switch back to IR mode The Blue LED will stay solid LED indicator Mode Blue LED Red LED Description IR Laser mode Solid IR las
3. 330m 130 0 209m longer arm mount required 0 244m 0 497m 1 972m 1 109m 2 263m 89 0 200m 0 125m 0 037m 0 125m 0 18 41 Specification I TouchBeam Touch Module Laser Safety Curtain to Screen 20mm 100mm 75 115 XGA WXGA 1080p Distance 40mm 100mm 12077140 16 6 ultra wide VO Por II General Specifications i i Auto Calibration Calibration Manual Calibration Multi touch 10 touch points Win 7 and Win8 compliant Multi touch Min Distance Hover Z depth Default hover height is 5 5mm 70 100 XGA co operate with TRO 33 UST projector Working Projection Image 85 115 WXGA co operate with TRO 27 UST projector 80 100 1080P co operate with TRO 25 UST projector 120 140 Ultra wide 16 6 co operate with TRO 25 UST projector Display mode Support Ceiling mode only IR camera cannot support hot plug Please unplug AC power cord of projector IR camera hot plug l before install IR camera lll Installation Software e Microsoft Windows XP SP3 Mouse mode supported e Windows 7 Windows 8 Touch mode 10 touch points OS Required supported and Mouse mode supported Windows NET Framework 4 0 installation is required System Requirements e Max OS X 10 7 10 10 Processor Type Intel Core i3 or above 2GB or higher Min HHD Space 110 MB 42 J gt i 43
4. alignment 4 4d IR Beam IR Beam Frame Frame gt 3mm lt 3mm It is suggested that a whiteboard with a frame of less than 3mm is used However if a larger frame size is required it must follow the conditions shown below Surface treatment Matt with mold texture 211010 Shape as figure on next page Whiteboard Projected image IR Beam Measuring projection surface flatness vw Criteria overall surface flatness should have variance of less than 5mm v Equipment leveling instrument 1 2 1 5m and thickness gauge o KGS Lo Q d y Split projection area into 16 segments equally as shown on chart below Place leveling instrument on whiteboard Insert the 5mm thickness gauge at point 1 9 positions following below order Horizontal Vertical Measure point 1 2 amp 3 Measure point 1 4 amp 7 Measure point 4 5 amp 6 Measure point 2 5 amp 8 Measure point 7 8 amp 9 Measure point 3 6 amp 9 OOE E E O CECE If a 5mm thickness gauge cannot be inserted between the whiteboard and the level then the whiteboard is not suitable for finger touch control 11 Installation guide Installation workflow Install the projector mount See mount installation guide Attach the projector to mount See mount installation guide Connect sources to the projector Adjust projected images See mount installation guide Install the whiteboard See whiteboard installation guide
5. thumbwheel clockwise e To lower the right hand side of the projector loosen the thumbwheel anticlockwise 18 Step 7 Adjusting the tilt horizontal keystone je al Loosen anticlockwise e The projector mount is pre tensioned and can be rotated by hand e Adjust the highlighted thumbwheel to fine adjust the rotation of the projector Fig 7A e To bring the left hand side of the projector closer to the screen tighten the thumbwheel clockwise e To bring the right hand side of the projector close to the screen loosen the thumbwheel anticlockwise 19 Installing the whiteboard e Please refer to the whiteboard installation instructions Note The whiteboard and projector should be installed centrally to each other The bottom of the image must be a minimum of 10mm from the bottom of the whiteboard border Enough room must be left on top for the TouchBeam module Note If the whiteboard is already installed please see page 36 20 Installing the TouchBeam module Step 1 Mounting the TouchBeam module 1 Open top cover with a screwdriver 1 2 Mount bracket to whiteboard or wall The module must be installed away from the projected image At least 13 5cm from the base plate At least 10cm from the bottom of the TouchBeam module 1 3a For short term dem
6. 15 Step 4 Adjusting the projected image size e Loosen the two bolts on the projector caddy Fig 4A e Loosen the bot on the fine length adjustor Fig 4B e Slide the caddy and fine adjuster together until the screen size is nearly correct Fig 4C e Tighten the fixing bolt on the fine adjuster Fig 4D e Adjust highlighted bolt to fine adjust the throw distance Fig 4E e To reduce the projected image size tighten the bolt clockwise using one of the allen keys provided to move the projector closer to the screen e To increase the projected image size loosen the bolt anticlockwise using one of the allen keys provided to move the projector away from the screen e Once fine adjustment is done Tighten the two caddy mounting bolts Fig 4F 16 Step 5 Adjusting the tilt vertical keystone e Loosen the single M8 x 75mm bolt Fig 5A e Adjust the projector to the required angle Fig 5B e Tighten the bolt to lock the angle of the projector Fig 5C e Adjust the highlighted thumbwheel to fine adjust the tilt angle Fig 5D e To decrease the angle of projection tighten the thumbwheel clockwise e To increase the angle of projection loosen the thumbwheel anticlockwise 17 Step 6 Adjusting the tilt yaw e Adjust the highlighted thumbwheel to fine adjust the yaw angle Fig 6E e To lower the left hand side of the projector tighten the
7. TouchBeam Interactive User manual Table of contents Usage NOE ZGRANA ENAR AAA 2 Precautii ON Sea AE EC a book 2 IOWIE WOS ENSO O OE 2 Package OVETVIEW anserina erindrede 3 Before Installation Environment Check WoW daw seee 4 To chBeamanstallatiom Intormat Orsa WA O dk da 5 UWE akse Ude IA SE eee te eer ton ER EEG Se SP AAA ee 6 Measuring projection Surface FATA ESS auc AW Dar rer une a a LO Mstallatio GUNG messan Earle eee 11 Install tioh WORK OW AO WA a dz a dE dd Az 11 instaline the MOUSE O OE ORC A EOS OGAE 12 Step 1 Attach the wall plate to the walk masaeacodawiwocnaadawinkokcwawiawicina L2 Step 2 Attach the projector to the mount plate esse ea aaa aaa serene sener eee eee renser eres reen ere rese 3 Step O Attach the Projector tothe MOUN aaa ORA ER i rarere Step 4 Adjusting the projected Image SIZE awa k o Gia k GE Gd E 15 Step 5 Adjusting the tilt vertical keystone eesea aaa aaa aaa renere ren seere renee aazazeaccci1 LO SEED 6 Adj stine ER SEND WIE zad rl kin EPE GO al O Sac Step 5 Adjusting the tilt horizontal keystone eeseuaaa aaa aaa aaa aaa aaa aaa aaa aaa anna LO Installing the WILE DOAN Cosi oai dO A AP Ea iR WA ZOO Oo EA 19 Installing the TouchBeam MOdUIEGE ZEE REGEL a R oc Edek SCE boy ene Wda 20 Step 1 Mounting the TouchBeam module esessaee aaa senere aaa aaa aaa aaa eee een aaa aaa aaa waza aaa aaa eee rer 20 Step 2 Install Utility SO
8. WA Enana CRO Ka AAA AZ A 22 SCP aS Cea A AG E ee ee eee 23 Stepa Operon ModE rerun aara ROR O cO O A On OEG 24 Step 5 LT OUCHBEAMAJENME D Gein EA a O EO a 25 SUED G TOUGH Area SORO aa zaba ii dA A ata 28 SIEDZCGBralOfasma ido E EA GN 30 Step 8 Touch SENSICVICY WER ORA A AE OWCA ba Gai RO OL Step 9 TROUDICSMOOUING VIEWER casonas o a GA W AA Aa oO A EE 32 ADDENADC ii Oi casas acre ees sca eo aa aib iii ii 33 NFOBORESROOUNEG GRO EA OO R PA AC AA PAR AE MACA 33 teracuve cable TAN SUE Rad RARE OKAZ A A O AA OOO 38 DISODECCZICUJSTOR toca Ra KOGA O O O i a za ZOE T a NERE 39 SDECIICANO Me wa cziuom aiicni E O NTE io kod dad OW AAC 41 Usage Notice Please follow all warnings precautions and maintenance as recommended in this user s manual Warning Do not disassemble the TouchBeam module Warning Do not use store or leave the TouchBeam module near fire or in places with a high temperature e g in direct sunlight or in sun heated cars e Warning Use a standard USB cable maximum length 5m To extend the USB cable length over 5m a certified active extension USB cable is required Warning Do not allow liquid or foreign material to enter the TouchBeam module Precautions The IR camera on the projector receives infrared signals from the TouchBeam module which is attached to the whiteboard To operate normally The IR camera should face the projection area of the whiteboard Remove any obstacle in betwee
9. ange power saving settings Requare a pasrecrd whep Change when the computer sleeps Display Mate tet and ether terns langer or srmaller Connect t an external display NVIDIA Central Panel Search Control Porel Device Hanager H anage sudo dende Change what the power buttons do tTomputgr wakes Choose a power plan Adjust screen resolution How te comect monitor fecker refresh rate Power Options Advanced settings Select the power plan that you want to customize and 8 then choose settings that reflect how you want your computer to manage power High performance Hard disk Desktop background settings Wireless Adapter Settings Sleep USB settings EH USB selective suspend setting Power buttons and lid PCI Express m Drarerrar newer mananement Restore plan defaults Oe amp HH BH HH 5 Go to the official website of the laptop PC manufacturer and update the USB driver to the latest version 6 Use the USB cable included with your projector and check again If a USB extension is needed please contact your distributor 7 The USB port of your computer may not be working Please contact your IT staff 34 Q3 Why is the utility icon 63 red and not green 3 05 A Red icon 63 indicates a failed connection This may be caused by the following 1 2 3 4 8 Unplug re plug in the USB cable and check again Switch to ano
10. ck Projector Brightness Mode selection Lower lamp brightness ECO mode may affect both Auto Touch Area Setting and Auto Calibration Please switch to Bright mode to complete Touch Area Setting and Calibration 4 Please check Projector Display Mode selection To ensure accuracy of both Auto Touch Area Setting and Auto Calibration it is suggested to switch display mode to Bright Mode Presentation Bright H Movie User Q8 What to do when the mouse cursor h flashes or jumps on screen or when the Touch function does not work well for a certain projection area A 1 Check if there is strong ambient light shown on the whiteboard If yes turn off the light Check if there are any foreign objects on the whiteboard If yes remove the object Refer to Step 6 Laser Beam Alignment for detailed procedures to see if laser beam is aligned 4 Refer to Step 7 Touch Area Setting for detailed procedures check if Manual Touch Area boundary is located properly Q9 What to do when the projection area corner is insensitive or intermittent lines are observed A 1 Adjust the level of Touch Sensitivity to enhance sensitivity see Step 9 Touch Sensitivity for troubleshooting 2 If Touch function remains insensitive please check the optical port condition If dust or 3 particles are observed gently clean the optical port with dust blower Q10 What to do when the touch function is not accurate A Touch accuracy may be impa
11. cted when the Windows default display has been changed 1 Go to the setting page lt Start menu Control Panel Appearance and Personalization gt Control Panel Home Make it easier to read what s on your screen You can change the size of text and other items on your screen by choosing i one of these options To temporarily enlarge just part of the screen use the Adjust brightness Magnifier tool Calibrate color Adjust resolution EE display settings Smaller 100 default Preview Connect to a projector Adjust ClearType text Medium 125 Set custom text size DPI See also Personalization Devices and Printers 2 Select Smaller 100 Default and click Apply 38 Appendix Interactive cable layout 3 5mm Plug za 12V Output Curtain Module Detect GND LASER ENABLE 39 Distance calculator te Projected image Bottom of the projected image XGA a w u wem 2 www WXGA s a w u meme w w 0 375m 0 628m 2 370m 1 481m 2 795m 110 0 222m 2 02m 0 318m 0 571m 2 155m 1 347m 2 541m 100 0 202m 0 403m 0 656m 2 475m 1 547m 2 919m 115 0 232m 0 193m 0 446m 1 770m 0 996m 2 031m 80 0 179m 1 49m 0 249m 0 502m 1 992m 1 121m 2 286m 90 0 202m 1 64m 0 305m 0 558m 2 214m 1 246m 2 541m 100 0 224m 1 79m Ultra wide 0 467 2857m Lozim 05m 120 0193m 0 497 2976m Liem 3d8m 125 0201m 0527m 3095m 1161m
12. e Restore plan defaults NVIDIA Central Panel Cancel Go to official website of the laptop PC manufacturer and update the USB driver to the latest version Go to official website of the laptop PC manufacturer and update the BIOS driver to the latest version Use the USB cable included with your projector and check again If an USB extension is needed please contact your distributor The USB port of your computer may not be working Please contact your IT staff Q4 What to do when there is only single touch point A 1 Re plug USB cable from PC 2 Goto Control Panel and make sure Tablet PC Components is selected 35 Q5 Q6 mE mam maz uz f p 7 7 ON EJ Control Panel Programs Programs and Features Control Panel Home RER Uninstall or change a program View installed updates To uninstall a program select it from the list and then click Uninstall Change FI Turn Windows features on or Organize v Name Publisher Turn Windows features on or off To turn a feature on select its check box To turn a feature off clear its check box A filled box means that only part of the feature is turned on FIR RAS Connection Manager Administration Kit CMAK HF Remote Differential Compression FX RIP Listener E Network liveable Protocol SNMP e echo daytime etc Telnet Server TFTP Cl
13. een zone should completely overlaps the projected white frame Step 3 Finally check again if the green frame completely overlaps the projected white frame If not fine adjust again B 3 When the Touch Area is correctly located click close to exit 30 Step 7 Calibration A Select Auto Calibration 45 Operation Mode Touch Mode v Touch Area Setting Auto v Calibration Auto Note If the fail message pops up follow the steps shown below to troubleshoot the issues e Close all software applications e Reduce ambient light e Do not obstruct or shake lens during calibration e Check if projection image is clear If not adjust focus to sharpen the image If the Auto Calibration fail message still pops up on screen switch to Manual Calibration B Select Manual Calibration Operation Mode Touch Mode v e Touch Area Setting Auto v Ji Calibration Touch Sensitivity Note Manual Calibration is suggested for better accuracy 31 Step 8 Touch Sensitivity When touch function is unresponsive or writing is intermittent You can adjust the sensitivity by adjusting Touch Sensitivity level ES Operation Mode Touch Mode Touch rea Setting Auto U f j Calibration Touch Sensitivi Default 4 Max 10 most sensitive Min O least sensitive 32 Step 9 Trouble shooting Viewer Sometimes infrared red light IR light from ambient light sources may interfere wit
14. er ON Visible light mode Solid Blinking Visible light ON IR Laser OFF touch disabled Error Always ON Error of LD module occurred 8 Put top cover back on and tighten the screws 28 Step 6 Touch Area Setting A Select Auto Touch Area Setting Note ka Operation Mode Touch Mode w Touch Area Setting Auto JES Calibration Irl Manual Touch Sensitivity Quit all software applications Reduce ambient light Do not obstruct or shake lens during Touch Area Setting Check if projection image is clear If not adjust focus to sharpen the image If fail message pops up switch to Manual Touch Area Setting B Select Manual Touch Area Setting R BES Operation Mode Touch Mode w Touch Area Setting d 4 j J l i Calibration Auto Manual Touch Sensitivity 29 B 1 After the camera captures the projection image a Touch Area window will pop up If the captured image is not clear enough please re select Ambient light mode selection from Auto to Bright or Dim according to actual ambient light condition Then press Preview and the camera will re capture the image Close Ambient light mode Auto Brightness GB Touch Area Setting B 2 Touch Area Boundary Fine tuning Step 1 Click on P1 use mouse to drag P1 to upper left corner Align adjustable green zone with projected white frame Step 2 Adjust P2 to P4 accordingly adjustable gr
15. h touch performance The troubleshooting viewer shows real time images for debugging purposes Use the tab on the left side of the screen to switch to IR light viewer Any infrared light interference is now shown in the window Close Close F zoo a A E EN ee Visi le L ight pup oe 33 Appendix Troubleshooting Q1 Why won t the PC boot when the USB cable is connected to the projector 1 Unplug USB cable from PC or 2 Go to BIOS setup page of PC and modify the Boot priority order Choose Hard disk as top priority save the change and reboot PC 0 TOSHIBA MKG4656SX S1 Q2 What to do when Windows system cannot identify the USB device A 022 2 EH Unplug re plug in the USB cable and check again Switch to another USB port and check again Restart your computer and check again Go to Power Options in Control Panel check USB selective suspend settings status in USB settings under Advance Settings Switch to Disabled Wes 2 Control Panel Hardware and Sound r Control Panel Horne i i 7 Devices and Printers System and Security Addadesee Addaprinter Mouse Network and Internet Hardware and Sound Programs gg AutoPlay Change default settings for media or devices Play COs gr other media automatically User Accounts Change system sounds Appearance and Personalization Clock Language and Region Ease of Access Power Options Ch
16. ient FI Windows Gadget Platform E FI Windows Process Activation Service When should Calibration and Touch Area Setting be completed Please perform Calibration and Touch Area setting during first installation If the projector or whiteboard is moved Touch Area Setting and Calibration should be performed again When Laptop PC resolution is changed calibrate again For better accuracy please complete manual calibration If an overlarge offset is observed please perform Manual Calibration and see Step 8 Calibration for troubleshooting What to do when Auto Calibration and Auto Touch Area Setting both fail 1 Whenthe projectors OSD message is shown this may result in Auto Calibration failure and Auto Touch Area Setting failure Please wait until the OSD message is hidden before performing Auto Calibration and Auto Touch Area Setting 7 1024x768 60Hz 36 2 Please follow the troubleshooting steps shown below to perform Auto Calibration and Auto Touch Area Setting again a Quit all software applications b Reduce ambient light c Do not obstruct or shake lens during Calibration d Check if projection image is clear If not adjust focus to sharpen the image e If the Auto Touch Area Setting failed or Auto Calibration failed message pops up on screen again please switch to Manual Mode to complete Touch Area Setting and Calibration 3 Please che
17. iteboard frame 10mm gap e Image size 70 115 e From the top of image area a 207100mm gap must be kept away from the bottom of TouchBeam module e Fora whiteboard with a frame height of lt 3mm keep a 10mm bezel at left right bottom of the projected image area e For a regular whiteboard ex aluminum frame with a frame height gt 3mm keep a 50mm bezel at left right bottom of the projected image area For ultra wide 24 9 image size TouchBeam Module t 40 100mm gap Projected image Bezel 1 af 10mm gap e Image size 120 140 Ultra wide e From the top of image area a 407100mm gap must be kept away from the bottom of TouchBeam module e For a suggested whiteboard with a frame height of lt 3mm keep a 10mm bezel at left right bottom of the projected image area e Fora regular whiteboard ex aluminum frame with a frame height gt 3mm keep a 50mm bezel at left right bottom of the projected image area Note If the whiteboard frame thickness is greater than 3mm the reflected light interference from the whiteboard frame may be detected by IR camera This can compromise the touch function To reduce the risk of this happening it is recommend that a 50mm border is kept around the projected image instead of 10mm as shown in diagram on the previous page If the whiteboard frame thickness is less than 3mm ensure the reflected light interference is not observed when completing TouchBeam
18. n the IR camera and the TouchBeam module Do not place other infrared communication devices lighting equipment or residential heating equipment etc nearby Maintenance Gently clean the optical port with dust blower How it works TouchBeam covers the entire whiteboard with a thin invisible IR light When a finger or stylus breaks the TouchBeam IR light reflects to the IR camera The camera module tracks multiple touch points and reports positions to a PC or laptop via USB To optimize the touch function the whiteboard needs to be flat and in good condition without dents or warping Package Overview TouchBeam module 2x M2 6mm screws 2x M6 6mm screws Interactive cable 2x Alignment sticker TouchBeam bracket Double sided tape 5m USB cable 2x Passive pens CD user manual Before Installation Environment Check Before setting up and installing the projector and TouchBeam module ensure that the power supply and wiring work for the installation location of the mount in advance Note e Install the projector away from other electrical devices such as florescent lights or air conditioners Some kinds of florescent lights could interfere with the remote control of the projector e Werecommend to keep source cable length less than 20 meters to reduce external noise e Werecommend using a steel backed whiteboard e Make sure the projector is installed under the following conditions the projected image is a rectangula
19. onstration Adhere double sided tape enclosed in accessory box onto bracket then paste onto the whiteboard or wall Note 7 5 13 5cm from bottom of base plate 21 1 3b For long term use Use screws to fix the TouchBeam bracket onto the whiteboard Drill tip D O 2 3mm Screw type M3x6L Screw head D O lt 5 5mm thickness lt 2 5mm 1 4 Attach the module to the bracket with screws Note The right angle connector must plug into the TouchBeam module 22 Step 2 Install Utility Software 1 System requirements 2 To ensure normal operation of the touch function your computer must meet the system requirements shown in the table below System requirement Operating system Microsoft Windows XP SP3 Windows 7 32bit 64bit Windows 8 Must be installed NET Framework 4 0 CPU Intel Core i3 or above Memory 2GB or higher Min hard disk space 110 MB Install the software utility from the CDROM The status of the software is shown in the task bar the icons shown below describe the mode the software is set to Touch mode a 23 Step 3 Initial Setup For first time setup follow the installation guide to complete the installation procedure A it E3 Installation Guide Trouble shooting Viewer Restore Default Setting Language Setting English 24 Step 4 Operation Mode Windows 7 and Windows 8 operating systems support multi point touch control Users can select
20. r shape without any distortion the projector is tilted at an angle no more than 3 degrees vertically and horizontal in relation to the screen e When using the interactive function install the projector so that the projected image is within reach e Do not install the projector or screen in a location subject to direct sunlight If the projector and screen are subject to direct sunlight the interactive function may not operate correctly TouchBeam installation information Before installing the TouchBeam module the projection surface must meet the following conditions criteria 1 The screen surface is a flat smooth surface with no unevenness of more than 5mm The surface can either be a flat wall or a whiteboard For details on how to check surface flatness see page 8 2 The surface must be magnetic or allow for the TouchBeam module to be secured with Screws 5mm bow If the projection surface meets the criteria above the projector and TouchBeam module can then be installed in one of the following ways 1 Mount the projector and TouchBeam module to the wall 2 Mount the projector to the wall and attached the TouchBeam module to the whiteboard SS Image area Image area Whiteboard guideline When installing the TouchBeam module on a whiteboard please follow the guidelines below For standard aspect ratio 4 3 16 10 and 16 9 image sizes TouchBeam Module 20 180mm gap Projected image Bezel Wh
21. ther USB port and check again Restart your computer and check again Go to Power Options in Control Panel check USB selective suspend settings status in USB settings under Advance Settings Switch to Disabled Power Options Advanced settings Select the power plan that you want to customize and a then choose settings that reflect how you want your computer to manage power Control Panel H i anmol Panel Horne tr Devices and Printers y P af F 1 P Devi Plar T Sen end eosi Add a device Add a printer ouse ay evice Manager Network and Internet Hardware and Sound Programs User Accounts Appearance and AutoPlay Change default settings for media or devices Play COs gr other media automatically A mam volume Changesystemsounds iManage audi devices High performance Active High performance Hard disk Wireless Adapter Settings Sleep Desktop background settings Power Options Change power saving settings seguie a password whet Personalization z USB settings USB selective suspend setting Setting Disabled v Power buttons and lid Clock Language and Region change what the power buttons do zmput r wales Ease of Access g Change when the computer sleeps Choose a power plan Display Kiake tert and other ferns Langer ar smaller Connect te an external display Aust sereen regalutio How t correct monitor fecker refresh rat
Download Pdf Manuals
Related Search