User Manual
Contents
1. 113 on off output socket output manuall socket output manuall socket output manuall socket output manuall Enable switching on off the 13 18 1 output by calling output by calling Default Delay control Delay switching on the 15 138 1 Minutes output after a certain minutes Delay switching off the 16 138 0 Minutes output after a certain minutes output the output output control output by temperature switch on off the output Disable auto control the 22 159 0 output by temperature Over Enable the over temperature 23 170 1 temperature alarm alarm 170 MinTemp MaxTemp Disable the over 25 1 70 0 temperature alarm Temperature Enable the temperature 26 160 1 rapid rapid changing alarm changing Set time period and 27 160 Temp Time alarm temperature changing value Disable the temperature 28 160 0 rapid changing alarm SMS notification upon the 29 11 1 BUY ON cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Send En M Pere Default the socket output changing SMS notification upon the 31 12 1 Default the power supply changing warning tone tone i tone Default Check status Check socket operating 35 07 status 0004 Check Delayed switch 37 138 on off the socket parameters socket parameters parameters changing alarm parameters alarm parameters Reset to Reset the socket 42 08 factory settings BUY ON c2. TUTA S30 GSM POWER SOCKET USER MANUAL A Auto operates by temperature Available for power control of the heating or refrigeration plant to keep the environmental temperature within presetting range or at fixed temperature value SMS alarm when temperature rapid changing or reaching the pre set value When it detects the rapid changing or the reach of pre set alert value of surroundings temperature it can auto send the SMS alarm message to master s mobile phone Support 5 mobile phone users Auto time synchronization SMS notification upon external power source changing 1 2 Package contents 1 GSM power socket 1 unit 2 Temperature sensor 1 unit 3 User manual 1 unit 1 3 Sockets instructions Figure 1 TUTA S30 instructions 1 Data port 5 Indicator light Power GSM Output 2 Temperature sensor port 6 Socket plugs 3 M button 7 Power switch 7 www cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 4 Electrical outlet 8 SIM card holder Figure 2 Temperature sensor Instruction 1 Standard 3 5mm interface put into 2 of Figure1 2 Temperature sensor 1 4 Light indicator and Beep warning tone Power Green Turning off No power supply input Constant light Has power supply input GSM Blue Not installed SIM card or the power switch of socket is OFF Be busy or searching GSM network light Output Red Default turning Long Beep TUTA S30 i
3. Details of the functioning and advanced operation of this socket are described in this instruction manual cablematic TUTA S30 GSM POWER SOCKET USER MANUAL CONTENTS cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 3 8 SMS notification upon extension power supply Changing 23 ee e LA AL EU A aterasbioseree 23 EIA heck A A a 24 NE A A A O un 25 Chanter Man S aaa a to ido a a 26 Citra General TESEO a 26 Chapter 6 Maii Technical PAra ia 27 APS Ms cad i aaa 28 cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 1 Purchase a GSM SIM card mobile phone card from GSM network service and install it in the socket This SIM card number is referred as TUTA S30 number on this brochure 2 The user needs to activate the Caller ID Presentation function of SIM card and deactivate PIN code of the SIM Contact with GSM network service for support 3 Change the original password at the beginning use Be sure to keep the password and SIM card number secret Do not disclose this information to anyone other than the authorized users in order to ensure your safety For your safety A gt This socket was designed for home or office use Do not use it on the electrical appliance which is for industry or business operation for example iatrical appliances large heaters and refrigerates Before using this socket make sure that the mo
4. M button See 3 on Figure1 can be pressed for about 0 5 second to switch on or off the output of socket After adding user numbers to the socket users can send SMS command to control the power supply output Refer to Chapter 3 2 Power off 1 Turn the power switch to Off position The blue light turns off 2 The socket outlet can work as a normal power socket TUTA S30 can not be controlled by SMS commands M button is disabled A Note 1 If the GSM indicator light is not constant lights which imply the SIM card working normally all functions of this socket are invalid Check GSM network signal of the using place e The GSM network s signal strength may affect the socket feature Therefore before using the user should ensure that TUTA S30 is used in an area with a strong GSM network signal e or the first time use the user should perform a test run by sending 9 www cablematic TUTA S30 GSM POWER SOCKET USER MANUAL SMS to the socket This allows the user to check the GSM network connection of the socket 2 3 Add a Master number to the socket The user must edit and send the following SMS to socket via his her mobile phone the phone number will be the Master number in order to Add a Master number to the socket 00 Successful SMS reply Welcome to use TUTA S30 Your Password is 1234 2 4 The regulation of time amp Important note If TUTA S30 is being used for the first tim
5. Mode LowTemp HighTemp e Mode is the control selection For coldness mode 1 For warmness mode 0 e LowTemp and HighTemp means temperature value the range is 10 to 50 centigrade degree if LowTemp equals to HighTemp constant temperature control will be actived e Temperature unit is degree Celsius e Example 1 set commands 159 0 10 20 if the environmental temperature is 5 degrees bellow the limitation of 10 degrees in the command the socket output will be switched on to power heating apparatus and if the environmental temperature is 24 degrees above the limitation of 20 degrees in the command the socket output will be switched off and the heating apparatus stops working e Example 2 set commands 159 1 10 20 if the environmental temperature is 26 degrees above the limitation of 20 degrees in the command the socket output will be switched on to power cooling apparatus and when the environmental temperature is 7 degrees bellow the limitation of 10 degrees in the command the socket output will be off cooling apparatus stops working Successful SMS reply Status ON OFF Temp control function ON OFF Temp Mode Heating Cooling Range LowTemp HighTemp 20 W cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 3 5 3 Disable auto controlled by temperature Method The Master user sends following SMS message in order to Disable auto control the output by temperature 159 0 22 Successfu
6. Status ON Delay control function OFF e When the delayed switch off the socket command is received and if the the socket output is switched on the socket output will remain the switch on state and be switched off as the setting delayed time is reaching If the socket output is switched off it will be switched on immediately and be switch off again when reaching the setting delayed time After switching off the socket output the following SMS reply will be sent Status OFF Delay control function OFF Method The Master user sends following SMS message in order to Delay switching on the output after a certain minutes 138 1 Minutes 15 Delay switching off the output after a certain minutes 138 0 Minutes 16 e Minutes are time parameters its range is 0 720 e When Minutes is 0 the delayed switch on off the socket function will be invalid but the current output status won t be changed Successful SMS reply Status ON OFF Output will switch off on after minutes 16 W cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 3 4 Timed switching on the socket output 3 4 1 Enable timing switching on the output Description e The output of TUTA S30 can be set to switch on for a duration and then be switch off after the duration e If the socket output status is changed manually including pressing M button sending SMS and making phone call the preset timing delaying or temperature control of the
7. indicate that TUTA S30 output is switching on or off The SMS reply is same with Chapter 3 2 1 3 2 3 Switching on off by calling Description If the Master user calls TUTA S30 the socket output will be switched on or cut off automatically when the user hears the ring tone in the phone The calling will be hung up automatically if the user doesn t hang up the call Method The Master user sends following SMS message in order to Enable switching on off the output by calling 18 1 13 Disable switching on off the output by calling Default 18 0 14 Successful SMS reply Control the socket power output status by calling activated de activated 15 cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 3 3 Delayed switch on off the socket output Description e The output of TUTA S30 can be set to delay switch on or off for a period with SMS commands e When the delayed switch on off the socket function is applied the preset timed switch on the output function will be invalid at once e When the delayed switch on the socket command is received and if the socket output is switched on the socket output will be switched off immediately and be switch on again as the setting delayed time is reaching Contrarily if the socket output is switched off the output will remain switching off until the setting delayed time is reaching Afther switching on the output the following SMS reply will be sent
8. on off the socket functions the temperature control function will only be valid when power output is switch on including timed switch on or delayed switch on time period e For example TUTA S30 is used for the power control of the heating apparatus If users set the socket output on when indoor temperature is bellow 20 degrees and off when indoor temperature is above 28 degrees Meanwhile users set the TUTA S30 output is on from 9am to 5pm In this case the socket will control to switch on or off the output according to indoor temperature automatically from 9am to 5pm duration Method The Master user sends following SMS message in order to Enable auto control the output by temperature 159 1 20 Successful SMS reply Status ON OFF Temp control function ON Temp Mode Heating Cooling Range LowTemp HighTemp Then TUTA S30 can switch on or off the output automatically according to the temperature range setting 19 W cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 3 5 2 Set temperature range to switch on off the output Description After successful setting of temperature range the temperature parameter will be saved on the socket until TUTA S30 is reset to factory settings But the Auto controlled by temperature feature is applied only when command 20 be set Method The Master user sends following SMS message in order to Set temperature range to switch on off the output 21 159
9. temperature rapid changing alarm 160 1 26 Set time period and temperature changing value 160 Temp Time 27 e Temp The values lie in the range of 1 to 50 centigrade degree e Time The values lie in the range of 1 to 300 minutes Default Temp is 2 degree and Time is 1 minute Disable the temperature rapid changing alarm 160 0 28 Successful SMS reply Fast temperature changing function ON OFF Delta Time minutes 3 7 SMS notification upon the socket output changing Description TUTA S30 will default notify the user when the state of the socket output is changed with a SMS notification The Master user can enable disable this SMS notification Method The Master user sends following SMS message in order to 22 Ww cablematic TUTA S30 GSM POWER SOCKET USER MANUAL SMS notification upon the socket output changing Default 11 1 29 No SMS notification upon the socket output changing 11 0 30 Successful SMS reply Set no SMS notification when socket output changed Set SMS notification once socket output changed 3 8 SMS notification upon extension power supply changing Description TUTA S30 will default notify the user when the state of the extension power supply is changed with a SMS notification For example Main electricity supply lost Temp or Main electricity supply restore Status ON Temp The Master user can enable disable this SMS notification Method The M
10. ablematic
11. aster user sends following SMS message in order to set SMS notification upon the power supply changing Default 12 1 31 No SMS notification upon the power supply changing 12 0 32 Successful SMS reply No SMS notification upon main electricity supply changing 3 9 Beep warning tone Description A Beep warning tone will be sounded if the work state of TUTA S30 is changed 23 www cablematic TUTA S30 GSM POWER SOCKET USER MANUAL The Beep warning tone is default turning off The Master user can enable it by sending SMS command Method The Master user sends following SMS message in order to Enable the Beep warning tone 19 1 33 Disaable the Beep warning tone Default 1 9 O0 34 Successful SMS reply Beep alarm activated de activated 3 10 Check status Method The Master user sends following SMS message in order to Check socket operating status 07 35 After receiving the SMS commands TUTA S30 will reply one SMS message of socket status checking Number eee Status ON OFF TEMP Temp control function ON OFF Schedule control function ON OFF Delay control function ON OFF Check socket output status OOO 36 After receiving the SMS commands TUTA S30 will reply one SMS message of socket output status Status ON Temp 23 Check delayed switch on off the socket parameters 138 37 After receiving the SMS commands TUTA S30 will re
12. ature reaches MinTemp or MaxTemp centigrade degree Temperature alert function OFF Min Temp Max Temp 3 11 Resetting the socket 1 Description e This function resets all programmed settings to their original values including cleaning all user number timing parameter and temperature parameter e If the setting status is wrong or the malfunctions can t be corrected users can restore the socket to its original status to make it work normally 25 www cablematic TUTA S30 GSM POWER SOCKET USER MANUAL A Note This function needs to be used carefully as it also erases all setting values Method Method 1 Press the side M button of the device for 5 seconds Method 2 The Master user sends following SMS message to TUTA S30 in order to Reset the socket O8 42 Successful SMS reply Reset the socket to factory setting successfully A long Beep tone if enabled will be heard and it means resetting the socket successfully Chapter 4 Maintenance e If TUTA S30 does not in use for long time it should be powered off e Store and use the remote socket in suitable temperature Too high or too low temperature will likely to damage the socket e Try to keep the TUTA S30 and all its accessories dry Do not store and use it in the bathroom or other place with high humidity Do not allow pour water or other liquids into the socket otherwise it might cause malfunctions e Do not store and use the socket i
13. bile phones can be used well in the area otherwise do not put this socket into operation The power consumption of the appliances connected with the socket cannot exceed 3000W and the current cannot exceed 15A The electrical appliance which power consumption is higher than 1500W must be grounded Do not make two plugs of socket short circuit Do not touch the socket jack by any metal objects or hand This socket was designed for indoor use Don t use it in wet chemically aggressive or dusty environment Do not open the case unless maintenance needed Do not keep shaking or fall down this socket otherwise it can be damaged This socket is a wireless signal transmission socket Keep it away from electronic equipment likely to interfere with the wireless signals in order to avoid signals interference Switch off this socket and mobile phone when entering areas marked Explosive Might explode Closed wireless transceiver sockets etc Do not cast this socket in a fire as this may cause explosion This socket should only be operated from power approved by the socket cablematic TUTA S30 GSM POWER SOCKET USER MANUAL manufacturer The use of any other types of power may damage the socket A Keep the socket and its accessories out of the children reach Exception clause 1 We operate on a policy of continuous development We reserve the right to make changes and improvements to any of the sockets described in this docum
14. cablematic TUTA S30 GSM Power Socket User Manual Manual version 2 3 TUTA S30 GSM POWER SOCKET USER MANUAL TUTA S30 GSM Power Socket Thank you for purchasing the TUTA S30 The TUTA S30 GSM power socket is a remote controlled socket consisting of a GSM module The power supply output of the socket can be turned on or off remotely by the SMS Short Message System command or local controlled by pressing button It is an intelligent power supply socket controlled by users mobile phone at anytime and anywhere TUTA S30 is suitable for controlling electrical appliances which power consumption less than 3000W in household or office It is universal for all kinds of indoor power supply sockets With extended connected temperature sensor TUTA S30 can switch on or off the socket output according to the environment temperature It s available for power control of the heating or refrigeration plant to keep the environmental temperature within presetting range or at a fixed temperature value Furthermore a SMS notification will be sent to master s mobile phone if TUTA S30 detects the rapid changing or the reaching of pre set alert value of surroundings temperature TUTA S30 is mainly applied for house and office usage It is not suited for industry application especially in humidity or dust condition All services and functions need to be supported by the GSM network and a SIM card This brochure suits for TUTA S30 model
15. e or it has been reset the Master user must adjust the socket time according to the current time of SMS center Otherwise TUTA S30 will use the original time from 00 00 00 1 Jan 2004 Method The Master user sends following SMS message in order to Regulate the socket time 152 SIMCardNumber 1 e The SIMCardNumber should be the SIM card number of TUTA S30 Successful SMS reply The socket current time is yyyy mm dd hh mm 2 5 Socket output switching on off Method Method 1 To press M button 0 5 second See 3 on Figure Method 2 The Master user sends following SMS message to socket in order to Switch on the socket output 01 Switch off the socket output HO2H cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Successful SMS reply Status ON OFF Temp 23 Temp control function ON OFF Schedule control function ON OFF Delay control function OFF 2 6 External power supply notification TUTA S30 will notify the user when the external power changes The Beep Beep tones will be heart if enabled also a SMS notification will be sent if the SIM card is available Lost external power supply If the plug of TUTA S30 is disconnected from external AC power or lost of the AC power occurs all operating on TUTA S30 is de activated including M button and all SMS commands TUTA S30 will notify the user Main electricity supply lost Temp Resume external power supply If the AC po
16. e PIN code SIM card invalid Contact with local operator to check of it 7 The master number Other master is already set in the Change Master number or already exists socket recover to factory default setting 8 Invalid format Please Invalid command Refer to the user manual check and try again No authorization user Use the Master mobile phone to try the command again Note If the problem can t be solved with above guidelines contact to your local S o distributor or after service center Chapter 6 Main Technical Parameters Input power socket 110 230V 50HZ CEE 7 7 hybrid Schuko French plug Output power socket relay 110 230V 50HZ 230V 30A 30s 15A long term CEE7 4 German Schuko Operating temperature 10 C 50 C Store temperature 20 C 60 C Relative humidity 10 90 without condensation Communication protocols GSM PHASE 2 2 including data operation Data interface GSM SIM 1 8V 3 0V socket External temperature sensor 10 C 50 C GSM working band EGSM900 DCS1800 cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Appendix SMS commands list Category Command Regulate the socket time 1 152 SIMCardNumber users socket number Add a family number 4 06 FamilyNumber Add several family numbers 5 06 FamilyNumber1 FamilyNumber4 Delete a family number 6 113 FamilyNumber Delete several family 7 113 FamilyNumber1 FamilyNumber4 numbers simultaneous
17. ent without prior notice 2 For the latest socket information please visit http www i tuta com We don t guarantee for the document veracity reliability or any content except regulate in proper laws Including no guarantee for socket suitable market or suitable area promise 3 We hold no responsibility for the illegal use of this socket 4 We hold no responsibility for any loss of income or any special incidental consequential or indirect damages howsoever caused 5 The contents of this document are provided as is Except as required by applicable law no warranties of any kind either expressed or implied including but not limited to the accuracy reliability or contents of this document We reserve the right to revise this document or withdraw it at any time without prior notice Chapter 1 Features and accessories 1 1 Main function This socket uses a GSM SIM card Remotely operate by SMS command The socket be controlled and set by gt gt sending SMS commands Input 110V 250V 50Hz Output Max 15A for long duration operation Relay 30A 250V relay with two working status power on off for output outlet M button To manual control output power on off Delayed control socket output Auto operates by preset schedule Fixing time control output power on off gt gt gt gt gt gt gt External temperature sensor supported Send environmental temperature SMS to mobile phone 6 www cablematic
18. esponding day Everyda Monday Tuesday Wednesday Thursday Friday Saturday Sunday Monday to Friday B Co Po O e StartTime and EndTime Be consists of 4 digits hh mm and works on a 24 hour clock The StartTime and EndTime should be in the same day and the EndTime must be later than StartTime e The socket output will switch on at the StartTime and cut off at the EndTime e For example 129 1 0000 2130 0000 means time 00 00 hh mm AM 2130 means time 9 30PM Successful SMS reply Schedule control function ON OFF WorkDay StartTime EndTime 3 4 3 Disable timing switching on the output Method The Master user sends following SMS message in order to Disable timing switch on the output 128 0 19 Successful SMS reply Schedule control function OFF WorkDay StartTime EndTime cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 3 5 Auto control the socket output by temperature 3 5 1 Enable auto controlled by temperature Description e The external temperature sensor must be inserted into the I O port of TUTA S30 The output status of the socket can be controlled by the environmental temperature automatically e If users don t open the timed switch on the socket or delayed switch on off the socket functions the socket will control to switch on or cut off the output according to temperature setting e f users open the timed switch on the socket or delayed switch
19. l SMS reply Status ON OFF Temp control function OFF Temp Mode Heating Cooling Range LowTemp HighTemp 3 6 Temperature alarm 3 6 1 Over temperature alarm Description A range of temperature can be pre set onto the socket In this case if the surroundings temperature is detected out of the pre set temperature range the TUTA S30 will auto send the SMS alarm message to master s mobile phone This feature depends on the temperature sensor A4 Method The Master user sends following SMS message in order to Enable over temperature alarm 170 1 23 Set limits of temperature 170 Min Temp Max Temp 24 e MinTemp and MaxTemp The values can be set within the range of 10 to 50 centigrade degree Default MinTemp is 20 and MaxTemp is 30 centigrade degree Disable the alarm upon going beyond limits temperature 170 0 25 Successful SMS reply Temperature alert function ON OFF 21 www cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Min Temp Max Temp 3 6 2 Temperature rapid changing alarm Description A time period value and temperature changing value can be pre set onto the socket In this case if the surroundings temperature change to the pre set value within the pre set time period a SMS alarm message will be auto sent to master s mobile phone This feature depends on the temperature sensor A4 Method The Master user sends following SMS message in order to Enable the
20. n dusty e Do not use alcohol acetone and other similar solvents to clean it Wipe it with soft wet cloth e Do not attempt to open it except as instructed If the socket does not work normally try to resolve it as the guide of the general troubleshooting if to the problem can not be solved contact with the dealer immediately Chapter 5 General Troubleshooting No Solution turns off AC power is available 2 GSM indicator light Can t find or identify the SIM card SIM card no install properly turns off The power switch is OFF Power off the socket and check it again Power on the socket 3 Socket output cannot No power input Check TUTA S30 s external be changed by M The power switch is OFF AC power is available button 26 W cablematic TUTA S30 GSM POWER SOCKET USER MANUAL No General Trouble Possible Reason Solution Power on the socket All functions disable Caller ID presentation do not active Contact network provider to Indicator is working insufficient fee of the SIM card active SIM card function Pay for the card 5 Socket didn t TUTA S30 work abnormally Switch off the power check response of any SIM card or reset factory operation setting 6 After power on the Network signal weak or network If mobile phone s signal is socket GSM indicator weak too place the socket at keeps flashing other place with strong signal and try again SIM card PIN code actives Close th
21. nected with it the red indicator light is lighted constantly Otherwise TUTA S30 has no power supply for electronic appliance and the red light is turned off e Note If the socket output status is changed manually including pressing the M button sending SMS making phone call the preset timing delaying or temperature control of the socket will be invalid automatically and a SMS notification message will be sent to the Master but the setting time range and temperature range parameters will be saved until TUTA S30 is reset to factory settings 3 2 1 Switching on off by SMS Method 14 W cablematic TUTA S30 GSM POWER SOCKET USER MANUAL The Master user sends following SMS message in order to Switch on the socket output manually 01 9 Cut off the socket output manually O2 10 The Family users send following SMS message in order to Switch on the socket output manually 01 Password 11 Cut off the socket output manually 02 Password 12 e Password should be 4 digits password number Default 1234 e SMS reply will be also sent to Master user when Family users use these two commands to change the socket output successfully Successful SMS reply Status ON OFF Temp Temp control function ON OFF Schedule control function ON OFF Delay control function ON OFF 3 2 2 Switching on off by M button Keep press M button on the TUTA S30 for half a second The OUTPUT indecator light will turn on or off to
22. original password is 1234 e The maximum digits that are allows for the phone number is sixteen e TUTA S30 will reply to the user after it receives the SMS command A Note e The symbol must not be ignored when typing an SMS command e No allow any space within the commands 3 1 3 Add a master number to the socket Description If TUTA S30 is being used for the first time or TUTA S30 has been reset to factory settings the Master user s number must be programmed into the socket Method The user must edit and send the following SMS to socket via his her mobile phone the phone number will be the Master number in order to Add a master number to the socket 00 2 Successful SMS reply Welcome to use TUTA S30 Your Password is 1234 12 WwW cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Failed SMS reply If a user tries to add another Master user again TUTA S30 will send a notification via SMS stating The master user already exists The Master number should be changed Refer to Chapter 3 1 4 3 1 4 Change the master number Method Method 1 The Master user sends following SMS message in order to Change the master user s number 14 NewMasterNumber 3 e NewMasterNumber should be the new Master user s mobile phone number Method 2 TUTA S30 should be reset to factory settings to remove old Master number before setting the new one Refer to Chapter 3 11 Successful SMS
23. ply one SMS message of Delayed switch on off the socket parameters checking Status ON OFF Output will switch off on after minutes Check Timing switch on the socket parameters 128 38 After receiving the SMS commands TUTA S30 will reply one SMS message of 24 cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Timing switch on the socket parameters Schedule control function ON OFF WorkDay StartTime EndTime Check Temperature control parameters 159 39 After receiving the SMS commands TUTA S30 will reply one SMS message of temperature parameters checking Status ON OFF Temp control function ON OFF Temp Mode Heating Cooling Range LowTemp HighTemp If No temperature sensor connected be received it means TUTA S30 cannot detect the temperature sensor User needs to check if the temperature sensor is inserted to the I O port Check temperature rapid changing alarm parameters 160 40 After receiving the SMS commands TUTA S30 will reply one SMS message of parameters It means SMS alarm message will be sent upon the surrounding temperature changes Delta centigrade degree within minutes Fast temperature changing function ON OFF Delta Time minutes Check over temperature alarm limits parameters 170 41 After receiving the SMS commands TUTA S30 will reply one SMS message of parameters It means SMS alarm message will be sent upon temper
24. reply New master number set successfully Successful SMS reply will be sent to the new Master user Then the old Master user s number will not be able to control TUTA S30 anymore 3 1 5 Add a family number Up to 4 family users number can be stored on one socket Family users have the authority to send SMS command to switch on or cut off the TUTA S30 output The family users should remember and safeguard the socket s SIM number Method The Master user sends following SMS message in order to Add a family number 06 FamilyNumber 4 Add several family numbers 06 FamilyNumbert FamilyNumberd4 5 e FamilyNumber should be the Family user s mobile phone number Y Successful SMS reply PH Family numbers set successfully 13 Ww cablematic TUTA S30 GSM POWER SOCKET USER MANUAL 3 1 6 Check family user s number Refer to Chapter 3 10 Check status 3 1 7 Delete family number Method The Master user sends following SMS message in order to Delete a family number 113 FamilyNumber 6 Delete several family numbers simultaneously 7 113 FamilyNumbert FamilyNumber4 Delete all family numbers 113 8 Successful SMS reply HE Family number has been deleted Failed SMS reply The family number does not exist 3 2 Switching on off the socket output manually Description e When the socket output is switching on TUTA S30 offers power supply for electronic appliance which being con
25. s successfully register GSM network or it is off successfully reset to its factory settings Note The Beep warning tone can be turn on or turn off by SMS command Refer to Chapter 3 9 for details Chapter 2 Quick start 2 1 Install the SIM card and temperature sensor e Turn the power switch to OFF position e Loosen the screw and open the socket s SIM cover you will see a SIM card holder cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Push the metallic cover of the holder to OPEN direction and open the SIM card holder Put the SIM card on the card holder ensuring that the beveled corner is toward the beveled corner of the SIM holder and the golden contact area is facing downwards Cover back the metallic cover and push it to LOCK direction The SIM card will be fixed in the holder Screw the SIM cover back Insert the temperature sensor into the I O port until it is seized 2 2 GSM Power on off Power on 1 2 3 4 Turn the power switch to On position See 7 on Figure Plug the TUTA S30 in an AC power socket See 6 on Figure The blue light will be flashing slowly for about 20 seconds then blue light be on constantly and a long Beep tone can be heard if Beep warning tone is enabled The default state of the socket outlet is no power supply output Insert the plug of electronic appliance in the TUTA S30 electrical outlet See 4 on Figure
26. socket will be invalid automatically but the setting time range parameters will be saved until TUTA S30 is reset to factory settings If these functions need to be restarted the following SMS commands must be set Timing 128 1 Temperature control 159 1 delayed switch on off the socket commands need to be reset Method The Master user sends following SMS message in order to Enable timing switch on the output 128 1 17 Successful SMS reply Schedule control function ON WorkDay StartTime EndTime If the value of the WorkDay StartTime EndTime on the SMS reply are all 0 it means the time duration has not been set Refer to 3 4 2 Then TUTA S30 will keep switching on or off the output automatically according to the schedule settings 3 4 2 Set time period to switch on the output Description After successful setting of time duration to switch on the socket output the schedule parameter will be saved on the socket until TUTA S30 is reset to factory settings But the timed switch on the output feature is applied only when command 17 be set 17 Ww cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Method The Master user sends following SMS message in order to Set time period to switch on the output 18 129 WorkDay StartTime EndTime e WorkDay one digit the values lie in the range of 0 to 8 The following table contains the descriptions of each value Value Corr
27. wer of TUTA S30 is available again the SMS notification will be sent to the user i e Main electricity supply restore Status ON OFF Temp When the external power supply is resumed the output of TUTA S30 will keep its previous working status For example if the output is switched on before the external power supply cut off the output will be switched on when the external power supply is resumed If the power supply is switched on and off frequently TUTA S30 will send reminding SMS messages Chapter 3 Advanced settings 3 1 Define the users 3 1 1 User authorization level All the settings of TUTA S30 can be set or adjusted via a SMS command There are two mobile phone user controlling levels 11 cablematic TUTA S30 GSM POWER SOCKET USER MANUAL Master user Only one Master user has authorization to use all features of TUTA S30 In order to enable all the functions on the socket the Master user must store his her mobile number in the sockets memory Only one Master s mobile number Master number is allowed for a socket Family users There are four Family users have authorization to use two commands of switch on or cut off the socket output The other mobile phone users have no authorization to use TUTA S30 3 1 2 About the SMS Command e Master user s SMS command format code content e Family users SMS command format code content password e The password must be a four digit number e The
Download Pdf Manuals
Related Search