Quick Install Guide
Contents
1. Does the PoE Outdoor work with existing smartBridges devices Yes The PoE Outdoor will work with all classic smartBridges radios It has automatic output voltage adjustment for different cable lengths for smartBridges classic devices upto 100m max Is PoE Outdoor rated for outdoor installations Yes The PoE Outdoor has a watertight NEMA box enclosure It has a wide operating temperature range of 40 Deg C to 60 Deg C 40 F to 140 F and 0 to 90 non condensing humidity tolerance PoE Outdoor Page 15 of 18 Appendix A Specifications Product No Ethernet Connector AC DC adaptor PoEO DC out Ethernet Data Rate Ethernet Data Cable Number of Ethernet devices that can power be powered Detection of Low DC input IEEE 802 3af signature detection Input Output status indication Surge Suppression Grounding Lug Remote Reset for smartBridges radios Operating Temperature Output voltage Relative Humidity Dimensions Unit Weight Products Supported Mounting 1 O Ports PoE Outdoor smartBridges to the future SB2830 RJ 45 48V RJ 11 cable ETH Out Pin 5 of RJ 45 output ve ETH Out Pins 7 8 of RJ 45 output ve IEEE 802 3af compliant 10 100 Mbps TIA EIA 568 Category 5 cable UTP STP Maximum length of 100m end to end 1 Yes with Output cut off at low DC inputs Yes Green Orange Blue LEDs Yes NEC 810 20 compliant Yes NEC 810 21 compliant Yes 40 Deg C to 60 Deg2. the device In this case Ethernet input cable to the PoE Outdoor carries only data The output cable to the radio would carry both data and power PoE Outdoor Page 10 of 18 smartBridges to the future Outdoor Wireless Radio e z eee j GQ 48VDC Power Sup Di ply RJ11 Cable from Grounding Lug Gn PoE Outdogr a RJ45 Cable 3 3 1 Wall Plate Installation The Wall Plate takes the RJ11 for Power and Ethernet IN for Data and provides Ethernet OUT with Power over the Ethernet cable The Ethernet Out connector is inside the Wall Plate The installation of Wall Plate is as follows 1 Remove the two screws holding the front and back of the Wall Plate and check whether the RJ45 connector ETH OUT and Wall Plate PCB are proper 2 The Knock out plate at the center of the back cabinet should be removed for taking the cable outside 3 Connect the ETH IN and RJ11 in and check whether LED on the Wall Plate PCB glows 4 Push the slide switch to straight or cross position depending upon whether the connection is to PC or network 5 Connect the Ethernet output cable through the hole at the back of the Wall Plate 6 Fix the Wall Plate to the wall with the screws provided inside the Wall Plate PoE Outdoor Page 11 of 18 smartBridges to the future 3 3 2 Ethernet or RJ11 Cable Connection to PoE Outdoor Note Please do not insert the Ethernet cable or RJ11 cable
3. with the connector crimped into the ETH IN ETH OUT or Power IN cable gland of the PoE Outdoor 1 Unscrew the four corner screws on the top side of the PoE Outdoor and remove the top cover Check whether the ETH IN ETH OUT and Power IN cable glands are punctured At the time of shipping the cable glands should be in closed conditions Use a small screwdriver to pierce a hole in the cable gland Do not let screwdriver touch the PCB components Insert the uncrimped Ethernet cable from outside the PoE through the cable gland and into the device Pull the cable for about 100 mm Strip both the outer sleeve of the Ethernet cable and the internal twisted pairs of wires to 6 mm length Insert the wires into the RJ45 plug and crimp the plug Gently pull back the Ethernet Cable through the cable gland and insert the RJ45 plug into the socket on the PCB To avoid accidental pulling of the Ethernet Cable use a cable tie over the Ethernet cable on the inner side of the PoE Outdoor After ETH IN and ETH OUT cables are connected screw the top cover back In the case of using direct power make sure the RJ11 DC In cable is connected Peel off the liner paper at the edges of the decorative label and stick the label edges on the top cover PoE Outdoor Page 12 of 18 smartBridges to the future 3 4 LEDs Status Upon connecting the RJ45 Output from PoE Outdoor to the smartBridges Device the statuses of the d
4. C 40 F to 140 F 48V for IEEE802 3af signature compliant devices Automatic output voltage adjustment for different cable lengths for smartBridges classic devices upto 100m max 10 to 90 non condensing 135mm x 80mm x 35mm 450gm All smartBridges Products and IEEE 802 3af compliant products Pole or Wall mounting via 2pc U Bolts and clamps supplied Water tight to NEMA 1 4 4X 6 12 13 IP66 EN60529 IKO7 EN30102 Page 16 of 18 smartBridges to the future Appendix B Warranty License and Copyrights Warranty Information smartBridges warrants product to be free of defects and agrees to repair or replace the product that proves defective PoE Outdoor is warranted for one year from date of purchase This warranty does not cover accidents misuse neglect unauthorized product modification or acts of nature Please visit customer support area of smartBridges web site for making warranty claims smartBridges may elect to exchange the product or refund the full purchase price of the unit Except as expressly provided above smartBridges makes no warranties or conditions express implied or statutory including without limitation the implied warranties of merchantability and fitness for a particular purpose or infringement of any patent copyright or other intellectual property right smartBridges shall not be liable for damage to other property caused by any defects in this product damages based upon inco
5. all Plate PoE Outdoor Wall Wall Plate Provided as Standard accessory RJ45 from PC Hub ETH IN from Wall Plate RJ11 from AC DC Adapter v from Grounding Lug to ground Steps for Ethernet and Power connection using the wall plate 1 Connect the 48V AC adapter to the AC mains inlet 2 Connect the RJ11 cable of the AC adapter to the Wall Plate Make sure the RJ11 connections are not reversed PoE Outdoor Page 9 of 18 SmartBridges to the future 3 Using an RJ45 crimped CAT5 cable connect the PC Network to the Wall Plate 4 Connect an outdoor rated shielded Ethernet cable from the RJ45 output of the Wall Plate Refer to section 3 3 1 for installing the wall plate to the ETH IN of the PoE Outdoor refer to section 3 3 2 for connecting the Ethernet cables to the PoE Outdoor 5 Secure the outdoor rated Ethernet cable along the wall and outlet hole properly Provide strain relief on this CAT5 cable 6 From the ETH OUT jack on the PoE Outdoor connect an outdoor rated shielded CAT5 cable to the radio on the roof top or tower Provide strain relief for this CAT5 cable Installation Diagram without Wall Plate PoE Outdoor gt gt sonuca A ETH OUT to Radio RJ11 from AC DC Adapter RJ45 from PC Hub ETH IN from Grounding Lug to ground Note Optionally the RJ11 cable can be directly connected to the RJ11 input jack inside PoE Outdoor to power
6. evice is indicated with the following LED color codes 1 Open Circuit 3 Green Blinking 2 Short Circuit Green Amber and Blue Blinking 3 smartBridges Classic mode 3 Solid Amber 4 IEEE 802 3af mode Solid Blue 5 Undefined mode Amber and Blue Blinking 3 5 Protection Transient Voltage Suppressor TVS Each of the four RJ45 data lines is clamped to 7 5V and the TVS provides protection against High Voltage transients The RJ11 power lines are clamped to 60V Grounding is done through the grounding lug at the back of the PoE Outdoor The TVS offers very quick response time to transient high voltages TVS Rating 1 Peak Pulse Power Capability 1500 W with a 10 100 micro second waveform 2 Repetition Rate duty cycle 0 01 Gas Discharge Tube GDT The GDT can handle large surges The GDT triggers when exposed to long duration surges It has a high current rating to protect against surges Both the RJ45 data line and the RJ11 power lines are clamped to 90V with independent GDTs GDT Rating Discharge Current Capability 2 5KA 8 20 micro second waveform 10 times PoE Outdoor Page 13 of 18 smartBridges to the future 4 Service and Support This User Manual provides comprehensive information on Installation and Configuration of PoE Outdoor If however you still have problems or need further support you can get in touch with us at http Awww smartbridges com You can also send your queries to suppo
7. nvenience loss of use of the product loss of time or data commercial loss or any other damages whether special incidental consequential or otherwise whether under theory of contract tort including negligence indemnity product liability or otherwise smartBridges products are not intended for use in medical life saving or life sustaining applications In no event shall smartBridges liability exceed the normal purchase price for this product License No license express or implied by estoppels or otherwise to any intellectual property rights is granted by this document Copyright amp Trademarks Copyright 2003 smartBridges All Rights Reserved PoE Outdoor is a trademark of smartBridges All other trademarks and brand names mentioned in this Manual are registered trademarks or trademarks of their respective owners PoE Outdoor Page 17 of 18 smartBridges to the future Notes smartBridges to the future
8. nvenience in wireless network deployment Indicator LED a ETH OUT Ground Lug On the lower side Reset Default ETH IN The PoE Outdoor is compatible to all IEEE 802 3af compliant equipment Powered by an industry standard 48V AC DC adaptor the PoE Outdoor will provide sufficient power for devices connected up to 100m 328feet PoE Outdoor Page 4 of 18 smartBridges to the future Features Benefits Ethernet port protection and Special Special ground lug aids in direct and Grounding Facility efficient grounding of device to user power ground thus providing a ground drain path for electrostatic or lightning discharges NEC 810 21 compliant Two layered protection on Data I O and Protects from heavy surge currents and Power lines high voltage transients Short Circuit Protection Monitoring and protection ensures that power supply is switched off automatically while indicating the error status due to short circuit on the output ETH Out RJ45 jack Lightning Protection Discharge NEC 810 20 compliant Shielded RJ 45 Jacks Enables use of STP CAT5 e cables for protection against electrostatic discharge Auto Sensing of Cable length Dynamically adjusts power supply to compensate for voltage drop across the length of the cable Load Sensing Checks for PoE capable device and power consumption Diagnosis of Low supply voltage Switches off output power indicating error in power supply hence easy to troublesh
9. oot Detects presence of moisture in cables Weather proof Durable heat resistant NEMA 4 water tight casing for reliable outdoor deployment Remote Reset Switch Remotely restores the smartBridges radio to default settings Protection wn iS no Cc D amp Q ge O G gt ne Carrier Class PoE Outdoor Page 5 of 18 smartBridges to the future 2 Package Contents PoE Outdoor unit AC Adapter Cable for AC adapter Wall Plate Unit Earthing Tag M6 Nut RJ11 Plug Pole Mount U Bolts M6 Nuts M6 Spring Washers M6 Plain Washers Wall Plate Wall Plugs M4 Self Tap screws M4 washers Reset Pin User Manual PoE Outdoor Page 6 of 18 3 smartBridges to the future Installing the PoE Outdoor The following steps should be carried out to install the PoE Outdoor 1 2 5 Grounding Mounting Wall or Pole mountable Ethernet and Power Connection to the PoE Outdoor Two ways to do this a Using the wall plate to carry Power and Data via the Ethernet cable RJ45 b Using the AC adapter directly to carry power via RJ11 optional input and the Ethernet cable to carry only data via RJ45 LED Status after connecting RJ45 Output from PoE Outdoor to the smartBridges Device Protection of the PoE Outdoor device The details of these steps are in the next sub sections 3 1 Grounding 1 Crimp an AWG 10 earthing wire to
10. rt smartbridges com Please register PoE Outdoor on our product registration page 5 Frequently Asked Questions Does the PoE Outdoor work with non smartBridges radios The PoE Outdoor will work with all smartBridges radios as well as IEEE 802 3af compliant non smartBridges radios What is the power supply Is it supplied along with the device The PoE Outdoor works with a 48V power supply as specified by the IEEE 802 3af standards The power supply adaptor is currently supplied along with the device What is the maximum length to which the Ethernet cable can be pulled From the outdoor radio to the PoE Outdoor and from the PoE Outdoor to the Hub PC or the wall power source the total cable length can go up to 100m without compromising power supply or signal quality Is it compliant with NEC standards for installations The PoE Outdoor has Surge suppression capabilities NEC 810 20 compliant Is there additional grounding protection Yes The special grounding lug on the PoE Outdoor can be connected to an earthwire for additional grounding The PoE Outdoor grounding capability is NEC 810 21 compliant PoE Outdoor Page 14 of 18 smartBridges to the future What is the two layered protection offered by the PoE Outdoor The PoE Outdoor offers advanced two layered protection on the data and power lines Using GDTs and Transorbs significant surge protection is built into the PoE Outdoor
11. smartBridges o fu to the future PoE Outdoor Quick Install Guide smartBridges to the future This page intentionally left blank Table of Contents 1 POE Outdoor fscscacesacecactsiescetesannceceeie 2 Package Contents 3 Installing the PoE Outdoor 3 1 GLOUNCIG 00 ccccceeeeeeeteeeeeeteeeeeeeeeeeeeetnnaaees 3 2 MOUNTING iiciciiriednpeieed nviiendie dois 3 3 Ethernet and Power Connection 00 3 3 1 Wall Plate Installation ee 3 3 2 Ethernet or RJ11 Cable Connection to PoE Outdoor essees 3 4 LEDS SIUS opinn EE AEE ERRE 3 5 PHOLOCTION nieri iaa ANE ER Service and Support ccccceeeeeeees Frequently Asked Questions Appendix A Specifications cccccccceseeeees Appendix B Warranty License and Copyrights PoE Outdoor SmartBridges to the future Page 2 of 18 smartBridges to the future This page intentionally left blank smartBridges to the future 1 PoE Outdoor PoE Outdoor is a unique Power over Ethernet Solution for outdoor wireless installations The PoE Outdoor delivers required operating power and transmits data via the standard Category 5 Ethernet cable It eliminates the need for a separate 110 220 volt AC cable to the radio and significantly reduces cabling and outlet requirements The PoE Outdoor combines advanced protective and diagnostic features to bring unmatched co
12. the Earth Tag provided 2 Place this Earth Tag on the earthing stud at the bottom side of the PoE Outdoor 3 Fasten it with the M6 Nut provided tightly to the earth Tag of the PoE Outdoor 4 Connect the other end of the earth wire to the Power ground on the premises Note Grounding has to be done before mounting the PoE Outdoor on the wall or pole PoE Outdoor Page 7 of 18 smartBridges to the future 3 2 Mounting Mount the PoE Outdoor on the preferred wall or pole by using the supplied U Bolts clamps wall plugs and screws shown in the diagram below ETH OUT to Outdoor Radio ETH IN from a Wall Plat ee Ground Lug PWR IN from RJ11 only for direct powering PoE Outdoor Page 8 of 18 smartBridges to the future 3 3 Ethernet and Power Connection A convenient installation can be achieved by using a single Ethernet cable to run power and data to the PoE Outdoor unit This is possible by using the wall plate Without compromising power supply or signal quality the total cable length can go up to 100meters from the outdoor radio to the PoE Outdoor to the Network PC hub or wall power source It is recommended to keep the cable length from the Wall Plate to the PoE Outdoor as short and direct as possible The length of the RJ11 cable and the Ethernet cable can be extended inside the premises using extension couplers and cables of suitable length Installation Diagram with W
Download Pdf Manuals
Related Search