InfiniScale IV 36-Port QSFP InfiniBand Switch User Manual
Contents
1. Procedure 1 Place the ESD mat on the Floor where you will be working and put on the ESD strap Make sure the ESD strap is touching your skin and that the other end is connected to a verified ground 2 Choose which way you want the switch to slide out of the rack Either the side with the power supply units can slide out or the side with the IB connectors can slide out Mellanox Technologies Rev 1 5 8 Things to consider before choosing where to mount the rails and mounting plates Figure 6 Which Side of the Rack Do You Want the Connectors The distance between the rack and the door will be as little as 4 cm on one side of the rack and as much as 18 cm on the other side of the rack Keep in mind that there can be as many as 36 cables connected to the switch Do you want the connector side recessed in the rack to allow for larger cable bending radius Will the connector side be recessed past other equipment in the rack and will this be problematic 3 Take the 2 mounting plates and screw them to the switch with the notched side up Note They are right hand and left hand Place them with the notch at the top 4 Place them on the end of the switch that you want to slide out Use two of the flat head screws for each mounting plate There are three sets of holes in the mounting plate to choose from You can choose any of the pairs make sure that you pick the same pair for both mounting plates This allows you to reduce or incr2. OK This LED when lit indicates that the output from the power supply is 12VDC The PSU status indicators are located just to the left of the primary power supply unit and labeled PSU1 and PSU2 The following status conditions are possible Table 5 PSU Status LED Configurations LED Configuration Status O OK This power supply unit is delivering the correct DC supply Mellanox Technologies Rev 1 5 LED Configuration Status Error This power supply unit is NOT deliver O ing the correct DC supply Off This power supply unit is NOT receiving C any input power or this PSU is not installed 2 1 1 3 Fan Status Indicators The indicators labeled Fans are located just to the left of the primary power supply unit next to PSU 1 The following fan status conditions are possible Table 6 Fan Status LED Configurations LED Configuration Status O OK All fans are operating O O Error One or more fans is not operating Repair or replace the fan unit Off The fan unit is not receiving any power C Check that the fan unit is properly and com pletely inserted All fans must be operating while the power supply is plugged in Power must be removed within one minute of the fans failing to prevent damage to the switch 2 1 2 PC Connector The MTS3600 supports an I2C compatible interface on the front panel Th
3. BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THE ORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEG LIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS HARDWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Table of Contents Table of Contents Revision History About this Manual Intended Audience Related Documentation Conventions Switch Products Covered in this User s Manual Chapter 1 Overview Chapter 2 Chapter 3 Chapter 4 Appendix A Appendix B Appendix C Appendix D Appendix E Appendix F 1 1 Serial Number and Product Version Information Installation and Basic Operation 2 1 2 2 Switch Platform Hardware Overview 2 1 1 Status LEDs 2 1 2 I2C Connector 2 1 3 Optional Management Interfaces Advanced Management Only Switch Platform Installation and Operation 2 2 1 Installation Safety Warnings 2 2 2 Mechanical Installation 2 2 3 Power Connections and Initial Power On 2 2 4 Extracting and Inserting the Power Supply Unit 2 2 5 InfiniBand Cable Installation 2 2 6 Extracting and Inserting the Fan Unit 2 2 7 Replacing the Battery in the Management Module Management and Tools Overview 3 1 3 2 3 3 Network Mangemant and Clustering Software Unmanaged Switch Updating Firmware 3 2 1 Instructions for Reprogramming Over the InfiniBand Network 3 2 2 Rep
4. Errors Warnings Bad GUIDs LIDs Check 0 0 Link State Active Check 0 0 Performance Counters Report 0 0 Partitions Check 0 0 IPOIB Subnets Check 0 0 Please see tmp ibdiagnet log for complete log I Done Run time was 1 seconds I Added 3 in band devices root mymach gt To list the discovered mst inband devices run mst status root mymach gt mst status MST modules MST PCI module loaded MST PCI configuration module loaded Inband devices dev mst CA_M1 dev mst SW_M1 dev mst SW_M1 25418 sw005 HCA 1 lid 0x0001 47396 1 Lid 0x0011 48438 1 root mymach gt Lid 0x0003 Mellanox Technologies Rev 1 5 16 II Using the ibnetdiscover tool Run root mymach ibnetdiscover grep 00000006660abcd0 grep w Switch Switch 24 5 00000006660abcd0 MT47396 Infiniscale III Mellanox Technologies base port 0 lid 17 Imc 0 Note The resulting LID is given as a decimal number 4 Run mixburn with the LID retrieved in step 3 above to perform the In Band burning operation Burn the InfiniScale IV switch root mymach gt mlxburn d dev mst SW_MT48438_lid 0x0003 fw fw IS4 mlx qq I Querying device I Using auto detected configuration file MTS36000 1UNC_Al ini PSID MT_0C20110003 I Generating image WARNING Running quick query Skipping full image integrity checks Current FW version on flash 7 0 135 New FW version 7 0 138 Burning sec
5. Ka Indicators s nput voltage PSU 1 is good PSU Status PSU 2 Indicators 2 1 1 1 System Status Indicators The System Status Indicators are located just to the left of the primary power supply unit and labeled Sys The following status conditions are possible Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Table 4 System Status LED Configurations LED Configuration Status OK The system is up and running O Error A fault in the system most likely the firmware did not BOOT properly Off The system has no power 2 1 1 2 Power Supply Status Indicators The MTS3600 36 Port Switch is available with one or two factory installed Power Supply Units For switches with only one unit installed a second Power Supply Unit can be added to increase security and to add redundancy Figure 4 MTS3600 QSFP Front Panel Place for secondary Primary Power Power Supply Unit Fan Unit Supply Unit The primary power supply unit PSU1 is located on the right side of the front panel with PSU2 on the left side Status indicators are located just to the left of the primary power supply unit Each PSU also has three status LEDs on the right side of the PSU that indicate the internal status of the unit AC This LED when lit indicates input voltage between 90 and 264 Volts This LED when lit indicates a fault in the power supply
6. To extract a Fan Unit 1 Loosen the two thumb screws locking the fan tray in place One of the fan status indicators either green or yellow will remain on 2 Pull the fan unit out by pulling on the thumbscrews As the fan unseats the fan status indicator will turn off To insert a FAN Unit 1 Make sure the mating connector of the new unit is free of any dirt and or obstacles 2 Insert the fan unit by sliding it into the opening until slight resistance is felt Continue pressing the fan unit until it seats completely 3 Turn the two thumb screws to lock the fan unit in place Note The green fan status indicator should light and the yellow fan status should remain off If not extract the fan unit and re insert it After two unsuccessful attempts to install the fan unit power off the switch before attempting any system debug Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 2 2 7 Replacing the Battery in the Management Module TBD Need procedure Mellanox Technologies Rev 1 5 13 14 3 Management and Tools Overview 3 1 Network Mangemant and Clustering Software Download and install on all nodes the Mellanox OpenFabric software package for Linux Windows or other operating systems from the Mellanox software website http www mellanox com gt Downloads gt InfiniBand SW Drivers This software package provides connectivity for server and storage systems utilizing Hig
7. frei zu machen sind die Alimentation Stabilise e inside of the switch platform Netzstecker aller Netzteile Pour isoler completement le zu entfernen module en cause Il faut de brancher toutes les ali mentations stabilise es 2 2 4 Extracting and Inserting the Power Supply Unit With both power supplies installed in the redundant configuration either PSU may be extracted without bringing down the system Note Make sure that the PSU that you are NOT replacing is showing all green for both the PSU and status indicators Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Figure 10 Power Supply Unit Extraction To extract a PSU 1 Remove the power cord from the power supply unit 2 Grasping the handle with your right hand push the green latch release with your thumb while pulling the handle outward As the PSU unseats the PSU status indicators will turn off 3 Remove the PSU To insert a PSU 1 Make sure the mating connector of the new unit is free of any dirt and or obstacles 2 Insert the PSU by sliding it into the opening until a slight resistance is felt 3 Continue pressing the PSU until it seats completely The latch will snap into place confirming the proper installation 4 Insert the power cord into the supply connector Note The green PSU indicator should light and the yellow indicator should remain off If not extract the PSU and re insert it a
8. management tools as well as con nectivity software for servers and storage and is available on the Mellanox web site See Chapter 3 for more information Basic installation hot swapping components and hardware maintenance is covered in Installation and Basic Operation on page 2 1 1 Serial Number and Product Version Information The serial number and product version information are found on the label seen in the figure below Figure 1 Generic Product label S N MTYYWWFSSSSS DIN Rev XX PIN MTS36000 1UNC I GUID HHHHHHHHHHHHHHHH Made In IL Also on this label is the GUID identifier for the switch Mellanox Technologies Rev 1 5 2 2 Installation and Basic Operation 2 1 Switch Platform Hardware Overview Figure 2 shows the front and rear panel views of the QSFP switch The figure shows port configurations for the switch systems including the dual hot swap power supplies and hot swap fan module I2C connector RJ45 connector USB connectors VGA port connector and various status LEDs Figure 2 QSFP Switch System Front and Back Panels All InfiniBand connectivity is via the rear panel All connectors can support active cables 2 1 1 Status LEDs Figure 3 Power and System LEDs STATUS 8 A Handle DC output from System Status the PSU is OK Indicators STATUS There is a fault VAN in the PSU Switch Fan gt Sys Status Fans
9. provides front to back air flow The switch platform contains auto sensing 90 264 VAC connections for all possible PSUs Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual The installer should use a rack capable of supporting the mechanical and environmental characteristics of a fully populated platform The rack mounting holes conform to the EIA 310 standard for 19 inch racks Take pre cautions to guarantee proper ventilation for air intake at the front of the chassis and exhaust at the rear in order to maintain good airflow at ambient temperature Cable routing in particular should not impede the air exhaust from the chassis Note The switch platform can be either front or rear mounted The notion of front and back is arbi trary however rear is used consistently in this manual to refer to the side of the switch with the InfiniBand and Ethernet connectors 2 2 2 1 Installing the Switch in the Rack Tools needed Phillips Screwdriver ESD Strap ESD mat Parts included in the installation kit e 2rails 10 recessed flat head screws There are more flat head screws in the kit than are required for installing the switch I right hand mounting plate e 4 pan head screws 1 left hand mounting plate 4 metal washers e 2 rail slides e 4 sets of nuts and bolts for the mounting plates Figure 5 Rack Installation Kit Support Parts Left hand mounting plate
10. 1000 3 2 Class A Environmental Acoustic Sound power level EU EN61000 3 3 Class A Japan VCCI Class A EU IEC 60068 2 64 Random Vibration EU IEC 60068 2 29 Shocks Type I II EU IEC 60068 2 32 Fall Test ISO 7779 ETS 300 753 70 5 dB A or 7 1 Bel Scalability and Performance Reliability Availability and Serviceability Features Switching Performance Addressing Switching Capacity Simultaneous wire speed any port to any port 48K Unicast Addresses Max per Subnet 16K Multicast Addresses per Subnet 1 44Tb s Hot Swappable 1 1 Redundant Fan Module and Power Supplies Power Supplies Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 0 1 EMC Certification Statements Table 9 lists the approved certification status per switch in different regions of the world Table 9 Switch Certification Status FCC EN ICES Switch P N Class Class Class ee cTUVus CB USA Europe Canada P MTS3600R 1UNC A A A A NIK MTS3600Q 1UNC A A A A 0 1 1 FCC Statements USA Class A Statements 15 21 Statement Warning Changes or modifications to this equipment not expressiy approved by the party responsi ble for compliance Mellanox Technologies could void the user s authority to operate the equipment 15 105 a Statement NOTE This equipment has been tested and found t
11. Disconnecting Copper InfiniBand cables are heavy and not flexible as such they should be carefully attached to or detached from the connectors Refer to the cable manu facturer for special warnings and instructions gt 7 Rack Mounting and Servicing When this product is mounted or serviced in a rack special precautions must be taken to ensure that the system remains stable In general you should fill the rack with equipment starting from the bottom to the top 8 Equipment Installation This equipment should be installed replaced or serviced only by trained and qualified personnel 9 Equipment Disposal Disposal of this equipment should be in accordance to all national laws and reg ulations 10 Local and National Electrical Codes This equipment should be installed in compliance with local and national elec trical codes 11 Battery Replacement There is a risk of explosion should the battery be replaced with a battery of an incor rect type Dispose of used batteries according to the instructions 2 2 2 Mechanical Installation The switch platform uses a rack mounted switch designed for installation in a standard 19 rack with all ports on the rear of the enclosure The front of the switch includes a hot swap power supply module with an optional second PSU for redundancy hot swap fan tray and I O ports for an optional CPU advanced man agement board and an I2C I O port The hot swap fan module
12. Mellanox TECHNOLOGIES InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual P N MTS3600Q 1UNC MTS3600Q 2UNC MTS3600R 1UNC MTS3600R 2UNC Rev 1 5 Mellanox Technologies 2 Rev 1 5 Copyright 2008 Mellanox Technologies All rights reserved Preliminary information Subject to change without notice Mellanox Technologies ConnectX InfiniBlast InfiniBridge InfiniHost InfiniRISC InfiniScale and InfiniPCI are registered trademarks of Mellanox Technologies Ltd Virtual Protocol Interconnect is a trade mark of Mellanox Technologies Ltd All other trademarks are property of their respective owners InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Document Number 2983 Mellanox Technologies Inc 350 Oakmead Parkway Sunnyvale CA 94086 U S A www mellanox com Tel 408 970 3400 Fax 408 970 3403 Mellanox Technologies Ltd PO Box 586 Hermon Building Yokneam 20692 Israel Tel 972 4 909 7200 Fax 972 4 959 3245 NOTE THIS INFORMATION IS PROVIDED BY MELLANOX FOR INFORMATIONAL PURPOSES ONLY AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL MELLANOX BE LIABLE FOR ANY DIRECT INDI RECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR
13. SU Make sure the mating connector of the new unit is free of any dirt and or obstacles Replace the PSU The power LED for the switch shuts off 1 2 Check that the there is adequate ventilation Make sure that there is nothing blocking the front or rear of the chassis and that the fan mod ules and ventilation holes are not blocked especially dust over the holes If you find dust blocking the holes it is recommended to clean the fan unit and remove the dust from the front and rear panels of the switch using a vacuum cleaner The green power LED for the fans does not come on Check that the Power LEDs are on Remove and reinstall the fan unit Make sure the mating connector of the new unit is free of any dirt and or obstacles See Section 2 2 6 Extracting and Inserting the Fan Unit on page 12 N Caution Do not run the switch if the System Status LED for the Fans is Yellow The link LED for the InfiniBand connector does not come on Pe bh Check that both ends of the cable are connected Check that the locks on the ends are secured Make sure that the latest FW version is installed on both the HCA and the switch If media adapters are used check that the all connections are good tight and secure The activity LED does not come on Check that the Subnet Manager has been started Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 4 1 Management Module How do I kn
14. Type D for India ACC000209 Power cord Type I for China ACC000210 Power cord Type J for Switzerland ACC000211 Power cord Type B for Japan ACC000212 Power cord Type I for Australia ACC000213 Mellanox Technologies Rev 1 5 8 Appendix A Avertissements de s curit d installation French 1 Instructions d installation Lisez toutes les instructions d installation avant de brancher le mat riel la source d alimentation lectrique 2 Temp rature excessive Ce mat riel ne doit pas fonctionner dans une zone avec une temp rature ambiante d p assant le maximum recommand de 45 C 113 F En outre pour garantir un bon coulement de l air laissez au moins 8 cm 3 pouces d espace libre autour des ouver tures de ventilation gt 3 Empilage du ch ssis Le ch ssis ne doit pas tre empil sur un autre mat riel Si le ch ssis tombe il peut pro voquer des blessures corporelles et des d gradations de biens gt 4 Connection d Alimentation electrique excedentaire dangers lectriques Ce produit comporte un couvercle transparent sur l espace pour alimentation lect rique redondante Ne pas faire fonctionner le produit si le couvercle transparent n est pas solidement fix ou s il est enlev gt 5 Orages dangers lectriques Pendant un orage il ne faut pas utiliser le mat riel et il ne faut pas brancher ou d b rancher les cables 6 Branchement debranche
15. ad and follow all of the instructions regarding the updating the firmware on your switch system Firmware for the HCA cards connected to this switch system can be downloaded from the same page 3 3 4 Using the Embedded Management Tools The embedded OS and tools on the CPU in the management module is a subset of the Mellanox OFED stack See http www mellanox com gt Downloads gt InfiniBand SW Drivers Select Mellanox OpenFabrics Enterprise Distribution for Linux MLNX_OFED Select the Linux User s Manual Mellanox Technologies Rev 1 5 20 Rev 1 5 Troubleshooting As soon as a switch is plugged in make sure that the green power LEDs on the PSU are on Power supply unit 1 If the AC power LED is off check that the power cable is plugged into a working outlet Check that the power cable has a voltage within the range of 90 264 volts AC Remove and reinstall the power cable If the AC power LED is green but the OK power LED is off or the amp LED is on Replace the PSU The Status green power LED for PSU1 or PSU2 does not come on 1 2 If the OK LED on the PSU is on but the system LED is off remove and reinstall the PSU Make sure the mating connector of the new unit is free of any dirt and or obstacles If the OK LED on the PSU is off check that OK LED on the PSU Unit is on Remove and reinstall the power cable Check that the power outlet in the wall is working Remove and reinstall the P
16. ce data 2 13 GND Ground 1 14 Rx3p Receiver Non Inverted Data Output 15 Rx3n Receiver Inverted Data Output 16 GND Ground 17 Rxlp Receiver Non Inverted Data Output 18 RxIn Receiver Inverted Data Output 19 GND Ground 20 GND Ground 21 Rx2n Receiver Inverted Data Output 3 22 Rx2p Receiver Non Inverted Data Output 3 23 GND Ground 24 Rx4n Receiver Inverted Data Output 3 25 Rx4p Receiver Non Inverted Data Output 3 26 GND Ground 27 ModPrsL Module Present 28 IntL Interrupt 29 Vcc Tx 3 3 V Power supply transmitter 30 Vcc 1 3 3 V Power Supply 31 LPMode Low Power Mode 32 GND Ground 33 Tx3p Transmitter Non Inverted Data Input 34 Tx3n Transmitter Inverted Data Input 35 GND Ground 36 Txlp Transmitter Non Inverted Data Input 37 TxIn Transmitter Inverted Data Input 38 GND Ground Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Appendix A Replacement Parts Ordering Numbers Table 11 Replacement Parts Ordering Numbers Part Description OPN Power Supply Unit PSU MTP000018 This Replacement part is for both the PSU 1 and PSU 2 Power supply blank MTM003600 Rack installation kit MTR003600 Fan Unit for QSFP MTF000960 Power cord Type B for USA Canada Mexico Taiwan ACC000204 Power cord Type H for Israel ACC000205 Power cord Type E F for Sweeden France Germany Neth ACC000207 erlands Russia Power cord Type G for UK ACC000208 Power cord
17. ease the distance the switch is recessed into the rack 5 Clip the nuts into the holes in the rack you will be using to connect the mounting plates Check that both sides of the switch are in the same position number on the rack The caged nuts are separatedby a single space 6 Take the 2 rail slides and screw them to the switch Use two of the flat head screws for each rail slide st Use these holes Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 7 Using two of the pan head screws and two of the washers for each rail install the rails to the end of the rack Place the rail behind the holes in the rack and screw the screws through the holes into the rails Figure 7 Sc rewing in the Rails 8 Place the two bolts for the caged nuts within reach 9 Slide the switch into the rails 10 Put the switch into place and screw the bolts into the nuts from step 5 Figure 8 Screw in the Mounting Plates Right hand _ mounting plate 11 You can start connecting all of the cables to the switch 2 2 3 Power Connections and Initial Power On The switch platform ships with one or two Power Supply Units For switches with only one unit installed a second PSU may be installed at a later time Each supply has a separate AC receptacle The input voltage is auto adjusting for 90 264 VAC 47 63Hz power connections The power cords should be standard 3 wire AC power co
18. edded Tools user manual included on the CD for further instructions 3 3 2 Accessing the management CPU There are two ways to access the management CPU via KVM connections locally via the Ethernet connector for remote access Management modules with a CPU will have the capability to allow remote monitoring and remote man agement of the chassis from any host connected to the fabric If the connection will be through the web then the host will need the capability to connect to the web 3 3 2 1 Accessing the CPU via Keyboard Video Mouse KVM For local access out of band management of the switch system 1 Rev 1 5 Connect a keyboard to the one of the USB ports a video device to the video connector and a mouse to the second USB connector of the switch cables not supplied Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 2 Login using the following user name and password User Name admin Password password Note User name and password are case sensitive 3 Change the default user name and password 3 3 2 2 Accessing the CPU via the Ehternet Connector For remote access out of band management of the switch system see the Embedded Managemnet Tools User manual or Quick Start guide for login information 3 3 3 Downloading Firmware Firmware for this switch system can be found at and downloaded from http www mellanox com gt Downloads gt Firmware Be sure to re
19. einstallation Diese Ger t sollte nur von geschultem und qualifiziertem Personal installiert ausge tauscht oder gewartet werden 9 Ger teentsorgung Die Entsorgung dieses Ger ts sollte unter Beachtung aller nationalen Gesetze Bestim mungen erfolgen 10 Regionale und nationale elektrische Bestimmungen Dieses Ger t sollte unter Beachtung der regionalen und nationalen elektrischen Bestimmungen installiert werden Mellanox Technologies Rev 1 5 11 12 Appendix A Special Regulations Regarding Finland Sweden Denmark and Norway Rev 1 5 Denmark This unit is class I and must be connected with an AC cord compliant with all national electrical codes in Denmark The AC cord shall have an integral ground wire and can only be plugged into a fully grounded outlet Do not connect this unit to any outlet that is not fully grounded Finland Laite on liitett v suojamaadoituskoskettimilla varustettuun pistorasiaan gt Norway Apparatet m tilkoples jordet stikkontakt Unit is intended for connection to IT power systems for Norway only Sweden Apparaten skall anslutas till jordat uttag Mellanox Technologies
20. el Scalability and Performance Features Reliability Availability and Serviceability Switching Performance Addressing Switching Capacity Simultaneous wire speed any port to any port 48K Unicast Addresses Max per Subnet 16K Multicast Addresses per Subnet 2 88Tb s Hot Swappable 1 1 Redundant Fan Module and Power Supplies Power Supplies Mellanox Technologies Rev 1 5 2 Table 8 MTS3600R Specification Data Rev 1 5 Physical Power and Environmental Size Weight Mounting Air Flow SerDes Speeds Connector Types 1 73 1U H x 17 5 W x23 8 D 44mm X 444mm X 605mm 22 045 lbs 1 PSU 24 60 lbs 2 PSUs 19 Rack mount 70 5 CFM 10 or 20 Gb s per port QSFP Input Voltage Power Consumption Temperature Humidity Shock and Vibration 90 264 VAC 47 63Hz 316W Dissipated Power 190W Power through connector 126W 10 to 45 Celsius 10 90 non condensing ETSI EN 300 019 2 2 1999 09 Protocol Support Regulatory Compliance InfiniBand Auto Negotiation of 20Gb s or 10Gb s Safety US Canada cTUVus EU IEC60950 QoS 8 InfiniBand Virtual Lanes for all ports International CB Management Baseboard Performance and Device man EMC Emissions USA FCC Class A agement Agents for full InfiniBand In Band Canada ICES Class A Management EU EN55022 Class A EU EN55024 Class A Data Rate DDR EU EN6
21. gain 2 2 5 InfiniBand Cable Installation All cables can be inserted or removed with the unit powered on To insert a cable press the connector into the port receptacle until the connector is firmly seated The GREEN LED indicator below each QSFP port will light when the physical connection is established that is when the unit is powered on and a cable is plugged into the port with the other end of the connector plugged into a functioning port After plugging in a cable lock the connector using the latching mechanism particular to the cable vendor When a logical con nection is made the yellow light will come on When data is being transferred the yellow light will blink Cables in the bottom row should be inserted up side down in relation to the how the cables are inserted in tehtop row Mellanox Technologies Rev 1 5 12 To remove disengage the locks and slowly pull the connector away from the port receptacle Both LED indicators will turn off when the cable is unseated Care should be taken not to impede the air exhaust flow through the ventilation next to the InfiniBand ports Cable lengths should be used which allow for routing horizontally around to the side of the chassis before bending upward or downward in the rack 2 2 6 Extracting and Inserting the Fan Unit Rev 1 5 Operation without a fan unit should not exceed one minute During fan hot swap if both indicators are OFF then the fan unit is disconnected
22. h Performance Computing HPC or enterprise data center EDC applications across an InfiniBand fabric It also provides a subnet manager for simple network configuration and network administration and diagnostic tools for net work management Switches can be either managed or unmanaged 3 2 Unmanaged Switch Updating Firmware The switch is delivered with the latest Firmware available at the time of production New firmware versions will be posted on the Mellanox firmware download page http www mellanox com gt Downloads gt Firmware You will need the Mellanox Firmware Tools package available in the Mellanox OpenFabrics software pack age to update firmware for this switch It can also be downloaded from http www mellanox com gt Downloads gt InfiniBand SW Drivers You will also need to download and unzip the firmware binary image This is provided in the Mellanox Web site at http www mellanox com gt Downloads gt Firmware and go to the InfiniScale IV Switch systems Click in the Table for the FW image that you need 3 2 1 Instructions for Reprogramming Over the InfiniBand Network Rev 1 5 To update an MT48436 InfiniScale IVswitch device having a specific GUID for example 0x00000006660abcd0 or LID the following are the recommended steps to update the device firmware 1 Make sure all subnet ports are in the active state One way to check this is to run opensm the Subnet Manager root mymach gt etc init d open
23. hich contains Embedded OS secure In band out band access Chassis manager amp System BIST SNMP Agent 3rd Party tool integration CLI and GUI Subnet manager Performance provisioning manager Congestion amp notification manager QoS manager Adaptive routing manager Cluster diagnostics manager Management modules with a CPU will have the capability to allow remote monitoring and remote manage ment of the chassis from any host connected to the fabric Mellanox Technologies Rev 1 5 18 The Subnet management features include upgrading Drivers upgrading software monitoring of AC power to the PSUs DC power out from the PSUs board temperature spine fan module unit leaf fan module unit failure in the switch system system failure in the switch system querying for board serial numbers and their revisions In addition the tools enable firmware management capabilities such as querying for existing firmware versions burning new firmware from scratch or for recovery from damaged firmware querying for and changing system GUIDs checking for duplicate or bad GUIDs 3 3 1 Embedded Cluster Management ECM The ECM tools are included in the management module and are accessed through KVM SSH Telnet the WEB Connection is made through either the video and USB connectors for KVM or the ethernet connector See the Emb
24. is interface is used to program firmware into the Flash Memory Firmware can also be programmed in band over the InfiniBand network See Section 3 for more details 2 1 3 Optional Management Interfaces Advanced Management Only The following interfaces allow access to the optional management module These interfaces have no func tion in unmanaged systems 2 1 3 1 VGA Interface The VGA port is for video output from the management module 2 1 3 2 RJ 45 Ethernet Connector The Ethernet connection provides access for remote management The MTS3600 can be connected to an Ethernet switch or the Ethernet port of a computer 2 1 3 3 USB interface There are two USB ports for connecting a keyboard and mouse for local management operation Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 5 2 2 Switch Platform Installation and Operation Installation and initialization of the switch platform are straightforward processes requiring attention to the normal mechanical power and thermal precautions for rack mounted equipment The switch platform does not require any programming or configuration to operate as a basic InfiniBand switch and includes all of the necessary functionality to operate with external standard InfiniBand Subnet Management software An Advanced Management option is available for the switch platform which includes InfiniBand Subnet Management software embedded internally i
25. ment des cables InfiniBand en cuivre Les cables InfiniBand en cuivre sont lourds et ne sont pas flexibles il faut donc faire tr s attention en les branchant et en les d branchant des connecteurs Consultez le fab ricant des cables pour connaitre les mises en garde et les instructions sp ciales 7 Montage et entretien sur baie Lorsque ce produit est mont ou entretenu sur baie il faut prendre des pr cautions sp ciales pour s assurer que le syst me reste stable En g n ral il faut remplir la baie avec du mat riel de bas en haut gt Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 8 Installation du mat riel Ce mat riel ne doit tre install remplac ou entretenu que par du personnel form et qualifi 9 Elimination du mat riel L amp limination de ce mat riel doit s effectuer dans le respect de toutes les l gislations et r glementations nationales en vigueur 10 Codes lectriques locaux et nationaux Ce mat riel doit tre install dans le respect des codes lectriques locaux et nationaux Mellanox Technologies Rev 1 5 10 Anhang A Installation Sicherheitshinweise German 1 Installationsanleitungen Lesen Sie alle Installationsanleitungen bevor Sie das Ger t an die Stromversorgung anschlie en 2 bertemperatur Dieses Ger t sollte nicht in einem Bereich mit einer Umgebungstemperatur ber der maximal empfohlene
26. n Temperatur von 45 C 113 F betrieben werden Au erdem sollten mindestens 8 cm 3 in Freiraum um die Bel ftungs ffnungen sein um einen einwandfreien Luftstrom zu gew hrleisten gt 3 Stapeln des Chassis Das Chassis sollte nicht auf andere Ger te gestapelt werden Wenn das Chassis herunt erf llt kann es zu Verletzungen und Besch digungen an Ger ten f hren gt 4 Redundanter Stromversorgungsanschluss Elektrische Gefahr Dieses Produkt verf gt ber eine Abdeckung ber dem Bereich f r die redundante Stromversorgung Betreiben Sie das Produkt nicht wenn diese Abdeckung nicht sicher festsitzt oder entfernt wurde 5 Bei Gewitter Elektrische Gefahr Arbeiten Sie w hrend eines Gewitters und Blitzschlag nicht am Ger t schlie en Sie keine Kabel an oder ab 6 Anschlie en Trennen von InfiniBand Kupferkabel InfiniBand Kupferkabel sind schwer und nicht flexible Deshalb m ssen sie vorsichtig an die Anschl sse angebracht bzw davon getrennt werden Lesen Sie die speziellen Warnungen und Anleitungen des Kabelherstellers 7 Rack Montage und Wartung Wenn dieses Produkt in einem Rack montiert oder gewartet wird sind besondere Vor sichtsma nahmen zu ergreifen um die Stabilit t des Systems zu gew hrleisten Im Allgemeinen sollten Sie das Gestell von unten nach oben mit Ger ten f llen Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 8 Ger t
27. n the switch This section describes the installation process and basic operation of the switch platform Please first read the warnings sub section carefully before carrying on with installation procedures 2 2 1 Installation Safety Warnings For Safety Warnings in French see Appendix E on page 32 and for German see Appendix F on page 34 For Special Regulations Regarding Finland Sweden Denmark and Norway see Appendix G on page 36 1 Installation Instructions Read all installation instructions before connecting the equipment to the power source 2 Over temperature This equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended 45 C 113 F Moreover to guarantee proper air flow allow at least 8cm 3 inches of clearance around the ventilation openings 3 Stacking the Chassis The chassis should not be stacked on any other equipment If the chassis falls it can cause bodily injury and equipment damage 4 Redundant Power Supply Connection Electrical Hazard This product includes a blank cover over the space for the redundant power sup ply Do not operate the product if the blank cover is not securely fastened or if it is removed 5 During Lightning Electrical Hazard During periods of lightning activity do not work on the equipment or connect or disconnect cables gt Mellanox Technologies Rev 1 5 6 6 Copper InfiniBand Cable Connecting
28. nt VCCI If this equipment is used in a domestic environment radio interfer ence may occur in which case the user may be required to take corrective actions Rev 1 5 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 5 Appendix A Switch Hardware Components Place for Optional Secondary Power Primary Power Supply Unit Fan Unit Supply Unit u Rn Mellanox Technologies Rev 1 5 4 Appendix A OSFP Interface 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 GND Rx2n Rx2p GND Rx4n Rx4p GND ModPrsL IntL VecTx Vec1 LPMode GND Tx3p Tx3n GND Tx1p Txin GND GND Rxin Rx1p GND Rx3n Rx3p GND SDA SCL Vcc Rx ResetL ModSelL GND Tx4p Tx4n GND Tx2p Tx2n GND Rev 1 5 19 18 17 Table 10 InfiniBand QSFP Connector Pinout 16 Connector Connector Deren 15 Pin Number Pin Name 14 1 GND Ground 13 2 Tx2n Transmitter Inverted Data Input 12 3 Tx2p Transmitter Non Inverted Data Input 11 4 GND Ground 10 5 Tx4n Transmitter Inverted Data Input 9 6 Tx4p Transmitter Non Inverted Data Input 8 7 GND Ground 7 8 ModSelL Module Select F 9 ResetL Module Reset 5 10 Vee Rx 3 3 V Power supply receiver 4 11 SCL 2 wire serial interface clock 3 12 SDA 2 wire serial interfa
29. o comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equip ment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 0 1 2 EN Statements Europe EN55022 Class A Statement Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 0 1 3 ICES Statements Canada Class A Statement Mellanox Technologies Rev 1 5 3 4 This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada 0 1 4 VCCI Statements Japan Class A Statement COREL F ALERET ERE ERMER VCCI D K DISIDTTZXMNFERH RETT CORE RER TEATS CBR HERZIEELTZLENBSNET TOGET HERE DN ED EET BEDPBKENSCECPHVET 0 1 5 Translation This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipme
30. o power supplies Mellanox Technologies Rev 1 5 InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 1 Overview Mellanox MTS3600 switch systems provide the highest performing fabric solution by delivering high band width and low latency to Enterprise Data Centers High Performance Computing and Embedded environ ments Networks built with MTS3600 systems can carry converged traffic with the combination of assured bandwidth and granular quality of service Built with Mellanox s 4th generation InfiniScale IV InfiniBand switch device MTS3600 systems provide up to 40Gb s full bidirectional bandwidth per port With 36 ports these systems are among the densest switching systems available These stand alone switches are an ideal choice for top of rack leaf connectivity or for building small to medium size clusters The switch comes pre installed with all necessary firmware and configured for standard operation within an InfiniBand fabric and requires an InfiniBand compliant Subnet Manager running from one of the hosts All that is required for normal operation is to follow the usual precautions for installation and to connect the switch to the HCAs Once connected the Subnet Management software automatically configures and begins utilizing the switch It is recommended that Mellanox OpenFabrics software package be installed on all nodes connected to the MTS3600 The software package provides a subnet manager and network
31. ond FW image without signatures OK Restoring second signature OK I Image burn completed successfully 3 2 2 Reprogramming the MTS3600 Through The I2C Port Rev 1 5 Use the MTUSB 1 adapter available from Mellanox to reprogram the switch firmware using a server or PC running MFT Figure 11 MTUSB 1 with Cables The MTUSB adapter has two connections for cables One cable is a I2C cable with male connectors on both ends The other is a USB cable with one type A host connection to be connected to the server or PC and a type B connection to be connected to the MTUSB adapter Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Figure 12 I2C Cable Connected to MTS3600 With the switch connected to a computer through the MTUSB it is now possible to reprogram the SPI Flash memory 3 2 2 1 Instructions for Reprogramming Through the I2C Port 1 Make sure that the MTUSB I2C cable is connected to the switch and USB cable is connected to a computer MFT is running on the computer mtusb 1 mst device appears in mst status 2 Set the MTS3600 I2C switch to allow access by running isw d dev mst mtusb 1 s shark p L1 3 Run the burn command flint d dev mst mtusb 1 i fw IS4 rel 7_0_142 MTS3600Q_Al bin qq b 4 Power cycle the switch by unplugging and re plugging the power cord to load the new firm ware 3 3 Managed Switch System The managed Switch system includes a CPU w
32. ow if the battery is dead 1 Replace the battery Mellanox Technologies Rev 1 5 21 InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Appendix A Specification Table 7 MTS3600Q Specification Data Physical Power and Environmental Size 1 73 1U H x 17 5 W x23 8 D Input Voltage 90 264 VAC 47 63Hz 44mm X 444mm X 605mm Power Consumption 326W Weight 22 045 Ibs 1 PSU Dissipated Power 200W 24 60 lbs 2 PSUs Power through connector 126W Mounting 19 Rack mount Temperature 10 to 45 Celsius Air Flow 70 5CFM Humidity 10 90 non condensing SerDes Speeds 10 20 or 40 Gb s per port Shock and Vibration ETSI EN 300 019 2 2 1999 09 Connector Types QSFP Protocol Support Regulatory Compliance InfiniBand Auto Negotiation of 40Gb s 20Gb s 10Gb s Safety US Canada cTUVus EU IEC60950 QoS 8 InfiniBand Virtual Lanes for all ports International CB Management Baseboard Performance and Device man EMC Emissions USA FCC Class A agement Agents for full InfiniBand In Band Canada ICES Class A Management EU EN55022 Class A EU EN55024 Class A Data Rate QDR EU EN61000 3 2 Class A Environmental Acoustic Sound power level EU EN61000 3 3 Class A Japan VCCI Class A EU IEC 60068 2 64 Random Vibration EU IEC 60068 2 29 Shocks Type I II EU IEC 60068 2 32 Fall Test ISO 7779 ETS 300 753 70 5 dB A or 7 1 B
33. rds including a safety ground and rated for 15A or higher Caution The switch platform will automatically power on when AC power is applied There is no power switch Check all boards power supplies and fan tray modules for proper insertion before plugging in a power cable Caution After inserting a power cable and confirming the green system status LED light is on make sure that the Fan Status indicator shows green If the fan status indicator is not green then unplug the power connection and check that the fan module is inserted properly and that the mating connector of the fan unit is free of any dirt and or obstacles Mellanox Technologies Rev 1 5 10 Caution When turning off the switch make sure ALL LEDS are off to ensure a pow ered down status Note Do not hot swap the power supply if your switch has only one power supply You must power down the system to replace the power supply unit when there is only one PSU in the switch Figure 9 Two Power Inlets Electric Caution Notifications CAUTION ACHTUNG ATTENTION Risk of electric shock and energy Gafahr des elektrischen Risque de choc et de danger hazard The two PSUs are inde Schocks Entferrnen des e lectriques Le de branch pendent Netzsteckers elnes Netz ment d une seule alimentation teils spannungsfrei Um stabilise e ne de branch Disconnect all power suppliesto alle Einhieten spannungs uniquement qu un module ensure a powered down state
34. rogramming the MTS3600 Through The I2C Port Managed Switch System 3 3 1 Accessing the management CPU 3 3 2 Downloading Firmware 3 3 3 Using the Embedded Management Tools Troubleshooting 4 1 Management Module Specification Switch Hardware Components QSFP Interface Replacement Parts Ordering Numbers Avertissements de s curit d installation French Installation Sicherheitshinweise German Appendix G Special Regulations Regarding Finland Sweden Denmark and Norway Mellanox Technologies Doosan Na QNuuuu U A Q e ee ee au amp oo pi I DR ee NN O0II I WR UUAN RD DD R A D On OU Rev 1 5 InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual Revision History Table 1 Revision History Table Date Revision Description January 2009 Rev 1 5 added installation instructions added ECM Removed Watermark November 2008 Rev 1 4 fixed weight in specs October 2008 Rev 1 3 Minor Formatting changes September 2008 Rev 1 2 Added Reprogramming the MT3600 Through The I2C Port section Added power cord OPNs to table 11 in Appendix D September 2008 Rev 1 1 Fixed link to Software package page September 2008 Rev 1 0 Initial release Mellanox Technologies Rev 1 5 InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual About this Manual This manual describes the installation and basic use of the Mellanox MTS3600 swi
35. smd start opensm start OK 2 Make sure the local ports are active by running ibv_devinfo 3 Obtain the device LID There are two ways to do that I Using the mst ib add command The mst ib add runs the ibdiagnet tool to discover the InfiniBand fabric and then lists the discovered IB nodes as an mst device under dev mst directory These devices can be used for access by other MFT tools root mymach gt mst ib add I Running ibdiagnet to discover the fabric Loading IBDIAGNET from usr local lib ibdiagnet1 2 W Topology file is not specified Reports regarding cluster links will use direct routes Loading IBDM from usr local lib ibdml 2 Mellanox Technologies InfiniScale IV 36 Port QSFP InfiniBand Switch User Manual 15 I Using port 1 as the local port I Discovering 3 nodes 2 Switches amp 1 CA s discovered I I Bad Guids LIDs Info I I skip option set no report will be issued I I Links With Logical State INIT I I skip option set no report will be issued I I PM Counters Info E I skip option set no report will be issued I I Fabric Partitions Report see ibdiagnet pkey for a full hosts list E I skip option set no report will be issued T I IPoIB Subnets Check T 32 I skip option set no report will be issued E I Bad Links Info I I No bad link were found I Stages Status Report STAGE
36. tch based on the InfiniS cale IV InfiniBand switch device Intended Audience This manual is intended for users and system administrators responsible for installing and setting up the switch platforms listed above The manual assumes familiarity with the InfiniBand Architecture Specification Related Documentation Additional Documentation available from Mellanox Table 2 Reference Documents Mellanox Firmware The MFT Mellanox Firmware Tools package is a set of firmware tools The man Tools MFT ual supplied with this package provides an overview of the firmware its installa User s Manual tion and replacement The MFT can be downloaded with its documentation at Document 2329 http www mellanox com products management_tools php Conventions Throughout this manual the name MTS3600 and the term switch are used to describe both the 36 port 40Gb s InfiniBand Switch and the 36 port QSFP 20Gb s InfiniBand Switch unless explicitly indicated oth erwise Switch Products Covered in this User s Manual Table 3 Switch Products Covered by this User Manual Product Number Description MTS3600Q 1UNC 36 port Unmanaged QSFP 40Gb s InfiniBand switch with one power supply MTS3600Q 2UNC 36 port Unmanaged QSFP 40Gb s InfiniBand switch with two power supplies MTS3600R 1UNC 36 port Unmanaged QSFP 20Gb s InfiniBand switch with one power supply MTS3600R 2UNC 36 port Unmanaged QSFP 20Gb s InfiniBand switch with tw
Download Pdf Manuals
Related Search