User manual type 34003092
Contents
1. is set to In these setups the Menu button must be disabled on the EXT controller Instead of using the Menu button to access the devices Menu use the alternative menu operation MEM In order to set these options press the following sequences within 10 seconds STOP STOP STOP STOP 8 Menu button deactivated 5 5 Kis NEGEH 1 Menu activated Power off option An EXT controlled device will always automatically power on when selected But it is not always practical if a device automatically powers off when another source is selected or the TV is turned off An example could be a Satellite receiver that is being used in more than one room If a user in a link room is watching programmes from the receiver it is not practical that the receiver automatically powers off when the user in the main room turns off the TV or selects another source If a recorder has been timed to record from the receiver it would also be a problem if the system automati cally powers off the receiver Many devices use so much time running a booting sequence that you might want them to never power off for this reason only In order to set these options press the following sequences within 10 seconds EC 7 Power off deactivated Eri 7 1 Power off activated one2. 5 remote controls can be used Beolink 1000 can be used with reduced functional ity This guide explains how This EXT controller is ready for use plug amp play See the opposite page regarding daily opera tion Some operations can be altered to improve interaction with other controllers or to your con venience Refer to the installation section further on if changes are needed one gt remote EXT controller When a scart type connected source is selected with a Bang amp Olufsen remote control the B amp O TV starts to parse control data from the remote control to the attached device via the scart cable The OneRemote EXT controller captures these data and converts these into IR data that can operate the specific device The converted IR data is being transmitted via a small IR emitter that has to placed in front of the device to be cont rolled Here it emits the same IR data into the front of the device that it was made to receive from its own remote control As an EXT controller operates on data received via the scart cable it will function only when attached to a B amp O TV If both the B amp O TV and the device are equipped with DVI and or HDMI sockets a suitable cable can be added to improve the picture quality The EXT cable will still be needed for control data and maybe also the sound Refer to the user manuals for both the TV and the device about correct installation of HDMI DVI cables In a setup wit
3. User manual type 34003092 EXT User manual English OneRemote EXT set top box controller Only for connection to a Bang amp Olufsen or compatible TV Operate these and other devices with a B amp O remote control Samsung DVDR Blueray players like BD C amp 200 and BD C8500 Operation with Beo4 or Beo5 one gt remote Daily use Playback and recording 6 OK Play Pause press 1 sec c NM Play Pause alternative a Menu o 5 Guide Return Stop co mm Disc menu u Rew co 2 Title menu FF co NEN Tools A Next o v Previous Exit co Hm Record Other operations 9 9 Text internal Ch list Info Special or alternative operations HM HM NUM 8 STOP Beolink 1000 and other remote controls Operation is optimal with Beo4 or 5 that has coloured function Beolink 1000 buttons Other remote controls can be used with limited operation Return Exit 585 This is special operation keys included on these remote controls Menu Play Pause alternative Power manual Record pause Open Internet Operation As on newer remote controls Green B Yellow C Blue D Red A one gt remote Congratulations The EXT converter from www oneremote dk can fully operate your device using your Bang amp Olufsen remote control terminal via a Bang amp Olufsen TV Beo4 or Beo
4. gt remote Installation The OneRemote EXT cable must be connected to the devices scart output socket and a scart input socket on the TV Then the IR emitter must be stuck in a way that it can emit IR light in to the the devices IR receiver that normally receives the IR light emitted thom the devices own remote control Only scart input sockets can be used that are able to send out linkdata to the EXT controller Also the TV must be programmed to send out data to the scart socket which is done in the TV s Sources menu Refer to the TV s user manual The EXT controller emulates DVD VMEM VTAPE SAT DTV VAUX and other sources There is no programming needed on the EXT controller The scartplug in that end of the EXT cable where the power supply and the IR emitter cable is attached MUST be inserted in to the devices output If not the EXT controller might not be able to power on and off the device correctly The control LED The EXT cable is equipped with a control LED build in to the scartplug that is inserted in to the device This LED assists in faultfinding if something is not operating correctly Continous flashing When power is applied to the EXT controller the LED will start flashing The flash indicates that the EXT controller has not received a command data from the TV since power on As soon as a command is received from the TV the LED wil stop flashing and light solid red or green If the control LED con
5. h link rooms all rooms will be able to operate the device via the link system one gt remote Operating with OneRemote To be able to operate the device correctly with a B amp O remote control the user has to be familiar with operations with the original remote control as described in the device s user manual B amp O remote controls are not equipped with many keys so we have designed a layout that works logically even when shifting between different devices To get a common layout for many devices we therefore needed to redefine a few of the beo4 buttons to other functions Go Record and Stop shifted operation Some of the buttons has two or three functions To get to these they have to be preceded with The buttons that has been assigned secondary functions on this controller can be seen in the operating table on page 2 Option programming The OneRemote EXT controller can be programmed with different options to fit different set ups An option programming is done by pressing a series of buttons in a special scheme that does not occur during daily use A pro gramming must be ended within 10 seconds To abort an ongoing programming sequence press 20 one gt remote Menu option If the device is used in a setup that includes a Bang amp Olufsen TV sometimes the use of the REW button creates a conflict Some Bang amp Olufsen TV act on the and enters its own TV On Screen Menu regardless of which source it
6. tinues flashing after you have selected the source on the TV where the cable is attached the socket does not include control data or the TV has not been set up correctly Refer to the TV s user manual LED colour The EXT controller will light red when it has detected a device that is powered on It will either flash or light solid red The EXT controller will light green when it is not connected to a device or if it is connected to a device that is powe red off If not connected to the TV output socket of a device the EXT controller will not be able to measure if the device is powered on and therefore always light green LED short flash off During use the LED will light red or green depending on the powerstatus of the device When receiving a controldata from the TV the control LED will shortly go out to indicate this If a button is pressed on the TV s remotecontrol supposed to operate the device and teh LED does not indicate this the TV has not been correctly set up www oneremote dk Made in Denmark 34003092uluk
Download Pdf Manuals
Related Search