ONE RELAY OUTPUT REMOTE CONTROL
Contents
1. on off mode output is on prolongs set on time of the output JP2 Off C Receiver relay output is set on for as long as transmitter button Not available JP1 On is pressed and sets off after short delay on button release JP2 Off D Pressing transmitter button 1 sets the output on Pressing E Pressing transmitter button sets output on Pressing button JP1 Off button 2 sets output off If button 2 is not pressed relay output 2 sets output off sets off after programmed time period 6 1 2 Output relay Monostable Mode pulse or Bistable Mode on off is programmed in steps 2 and 3 of programming procedures Delayed output set off reduces risk of unwanted interruptions in output set on continuity due to interferences caused e g electric motors Precise setting of this short delay timing is facilitated by programming 8 fold longer time delay of that needed Example to obtain 0 5s set off delay programmed delay of 4 5s delay must be made 0 5 x 8 4 Number of remote control transmitters that can be used in this mode is limited to 20 In modes A amp B jumper JP1 selects timing of switch over signal pulses at output S jumper On 0 25s pulse jumper Off 0 50s pulse Longer timing of switch over signal pulses is necessary for certain acoustic signalling devices in which shorter pulses are not recognized properly This mode requires use of hand transmitter with two or more buttons KEELOQ Encoding System In the s2. mm A 22222222 external buzzer sygnalizator akustyczny O Q 12VDC BHELUHAA CUpeHa Manufacturer IMPORTANT Output S must not be directly connected ELMES ELEKTRONIK 54 611 Wroclaw Avicenny 2 PL to pole of power supply see diagram above tel 48717845961 fax 48717845963 Low battery in transmitters is indicated either by its LED flashing UMBIOOHT or dimming and failing to light AN200HT Manufacturer s Limited Warranty This product carries two year manufacturer s warranty as from the date of purchase The warranty is limited to the replacement of faulty original parts or repair defects of improper manufacture Damage misuse or improper handling by the user or installer as well as any alterations in prod uct s hardware or software caused by unauthorized person violate warranty obligations and all due repair costs will be charged Elmes Electronic shall not be liable for any personal or material damage or loss resulting from any of its products direct indirect or partial use or failure to operate properly e mail elmes elmes pl internet www elmes pl Elmes Elektronik 09 2013 All rights reserved
3. RG1 switch for less than 2 seconds LED lights green b Press shortly button of the hand transmitter to be deleted receiver LED changes to red c Perform one of the following steps e Press button of any other Elmes made hand transmitter button or e temporarily disconnect receiver power supply or e wait round 30 seconds till receiver exits programming mode Correct performing of this procedure is confirmed by LED flashing red error indication Advice 1 Procedures 2 3 and 5 can be performed with the use of transmitter learned to the receiver memory Advice 2 Time for performing procedures 1 and 5 above is limited to 30 seconds If the procedures are not completed within this time period receiver exits programming mode and error is indicated SPECIFICATION UMB100HT transmitter radiated power lt 5mW battery 12V 23A AN200HT transmitter radiated power lt 10mW battery 9V 6F22 Receiver dynamic code system KEELOQ of Microchip Corp USA transmitter memory capacity 112 up to 20 in mode C superhet receiver module with sensitivity 106 dBm power supply range 11 17 VDC 50mA Operating temperature range from 20 to 55 C output relay max power rating 1A 120V AC 30VDC monostable output mode timing from 0 25s up to 4 hours bistable output mode on off signal output S 1A 60V max OC type sabotage alarm terminals NC type closed box external dimensions h w 1 24 46 73
4. e must be repeated 1 Learning transmitter s to receiver s memory maximum 112 a Press receiver s PRG1 switch for less than 2 seconds LED lights green b Press shortly hand transmitter button once receiver LED changes to red c Press shortly the same hand transmitter button again 2 Programming receiver output monostable operation mode pulse and output set on timing a Press receiver s PRG1 switch LED lights green and after two seconds changes to red Now release the switch b Press hand transmitter button Relay in the receiver sets on After required pulse time has lapsed press hand transmitter button again Relay in receiver sets off After 2 seconds receiver s LED starts flashing green confirming end of the procedure 3 Programming receiver output bistable on off operation mode a Press receiver s PRG1 switch LED lights green and after two seconds changes to red Now release the switch b Press transmitter button three times with less than 2 seconds intervals Receiver LED flashes green confirming end of the procedure 4 Deleting all transmitters in receiver memory Press and hold depressed PRG1 switch for more than 8 seconds Receiver LED first lights green After 2 seconds changes to red and after 6 seconds starts flashing green Now release the switch To learn new transmitter s follow procedure 1 above 5 Deleting single transmitter in receiver memory condition transmitter to be deleted is available a Press receiver s P
5. eiver s ground V on receiver s relay set ON and one pulse on relay set OFF Two pulses are generated also when pressed transmitter s button is used to prolong set on timing in monostable mode only mode A see Table above In operation modes D and E see Table above in which button 1 sets output on and button 2 sets output off two pulses are generated each time button 1 is pressed and one pulse each time button 2 is pressed LED Indication Receiver is equipped with two colour LED signalling power supply connection and status of relay output It lights red when power is connected and relay output is not activated When relay is set on it lights green Receiver Installation Receiver s place of installation should be dry and away from electromagnetic power lines radio transmitters metal screening and other devices that may cause interference and reduce operation range It is recommended to install the receiver well above floor ground level and test practical operating range of transmitter receiver set prior to firm installation The level of hand transmitter signals and local unwanted radio interference signals can be checked using optional Elmes RFM indicator e mail elmes elmes pl internet www elmes pl Elmes Elektronik 09 2013 All rights reserved PROGRAMMING PROCEDURES Receiver LED low flashing green in confirms properly performed programming procedure Fast flashing LED in red indicates programming error Programming procedur
6. elmes ONE RELAY OUTPUT REMOTE CONTROL SETS WITH DYNAMIC CODE Models U1HS ULHSD U1HSL U1HR receiver only EN This manual covers the following remote control products operation installation and programming Equipment Type Operating Range U1HS receiver UIHR 2 transmitters UMB100HT U1LHSD receiver U1HSR 2 transmitters DWB 100HT U1LHSL receiver U1HR 1 transmitter AN200HT UIHR UIHR receiver only E a All above listed products include the same superhet receiver model featuring e One galvanic separated relay output with NC NO terminals e One OC open collector transistor type signal output S pulse indicating relay output switch over e Two colour LED indicating state of the relay output e Highly sensitive and selective superhet receiver e Memory capacity of up to 112 keyfob remote control transmitters e KEELOQ dynamic encoding system Receiver Operation Modes UIHR receiver allows various operation modes depending on selection made by jumpers JP1 amp JP2 and programming Monostable pulse or Bistable on off relay output mode step 2 and 3 of programming procedures as shown in the Table below Table of relay output available operation modes Monostable Mode Bistable Mode JP2 On A Pressing transmitter button sets receiver s relay output on for B Each pressing of remote transmitter button sets receiver relay JP1 programmed time period Next pressing of the button while output on and off alternately
7. ystem newly encoded control signal is generated and sent each time transmitter button is pressed Receiver monitors code changes and responds to new code signals only Once received code will not be accepted second time This allows protection of radio transmission signals from deliberate code grabbing and unauthorized use 3 4 Transmitter Memory As each transmitter generates specific dynamic code receiver must learn and memorize individual coding of every transmitter that will operate with the receiver Therefore receiver s memory capacity is limited to 112 transmitters Learning 113 transmitter would delete first transmitter in memory etc Eliminating lost or stolen transmitters from receiver s memory requires deleting all transmitters and learning all remaining transmit ters again Deleting single transmitter from receiver s memory is possible only with the use of the transmitter to be deleted see pt 5 of program ming procedures Receiver Relay Output Receiver is equipped with galvanic isolated relay output with NO normally open and NC normally closed three wiring terminals one com mon The output switches over on command received from transmitter Details are shown on installation diagram included in this manual Signalling Output S The receiver features one open collector type OC signalling output for connecting to external acoustic siren or light strobe The output gener ates two pulses shorting to rec
Download Pdf Manuals
Related Search