SURPASS-S(850RGB) SURPASS-S(1300RGB) - Markus
Contents
1. 201 255 Zooming out and in CH7 000 010 No rolling Y AXIS 011 110 Fixed rolled position ROLLING 111 255 Rolling from slow to fast CH8 000 010 No rolling X AXIS 011 110 Fixed rolled position ROLLING 111 255 Rolling from slow to fast on 000 180 Fixed rolled position Z AXIS ROLLING 181 217 Rolling to clockwise 218 255 Rolling to anticlockwise CH 10 000 010 Original pattern CLIPING 010 074 Fixed cliping 24 ISIS e e USER MANUAL 075 104 Clipping out 105 144 Clipping in 145 184 Clipping out and in 185 224 Clipping on 224 255 Clipping off 000 009 Original pattern CH11 010 199 Wave effect in pattern with speed control WAVE 200 255 Wave effect in pattern with amplitude control 102 118 Cyan 119 135 White red green blue 4 fixed colors 136 152 Blue yellow purple cyan 4 fixed colors 153 169 Severn colors 170 186 White red green blue 4 colors looping 187 203 Blue yellow purple cyan 4 colors looping 204 220 Severn colors looping 221 237 Original color 000 063 Original pattern CH13 064 127 Pattern with bright points 128 191 Pattern with blanking 192 255 Points to make pattern 25 USER MANUAL PATTERN LIST DMX 000 050 051 101 102 152 153 203 204 254 USER MANUAL LASER POWER SURPASS S 850RGB 200mW 638R 150mMW 532G 400mW 450B SURPASS S 1300RGB 300mMW 638R 200mMW 532G 800mW 450B SPECIFICTAIONS _ Mains Input AC100 240V 50 60Hz Fuse 22. Power Supply To determine the power requirements for a particular fixture see the label affixed to the back plate of the fixture of refer to the fixture s specifications chart A fixture s listed current rating is its average current draw under normal conditions All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer 8 USER MANUAL channel is used solely for a 0 to 100 switch Before applying power to a fixture check that the source voltage matches the fixture s requirement The unit is supplied with a power plug appropriate to its voltage and destination Should any other connections be required they must be carried out with the following configuration FUSE 5mmx20mm FUSE E 1 A 250V L CableEU bas ik n Liht blue White Neutral N Yellow Green Green Earth L DMX 512 connection between fixtures The fixture is equipped with 2 pin XLR sockets for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view 1 Shield 2 Signal 3 Signal A Caution At the laser fixture the DMX cable has to terminate
3. 10 times the weight for 1 hour without any harming deformation e The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails e Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing e The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time e The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year e The fixture should be installed in the position where persons cannot reach and where persons may walk by or be seated CAUTION When installing the device make sure there is no highly in inflammable material decoration articles etc in between a distance of min 0 5 meter USER MANUAL PRODUCT OVERVIEW e This device has left out premise in absolutely perfect condition In order to maintain this condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual
4. abandon electronic product regulation in your country The projector must be installed in a location with adequate ventilation at least 50cm 20inches from adjacent surfaces Be sure that no ventilation slots are blocked USER MANUAL LASER SAFETY WARNINGS W Potential laser injury hazard exists with this product Read these Instructions carefully which include important information about installation safe use and service N Caution Avoid direct eye contact with laser J light Never intentionally expose your eyes or others to direct laser radiation N Caution This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes N Caution It is illegal and dangerous to shine this laser into audience areas where the audience or other personnel could get direct laser beams or bright reflections into their eyes N Caution Itis a US Federal offense to shine any laser at aircraft N Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact the dealer nearest to you N Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure NON INTERLOCKED HOUSING WARNING This unit contains high power laser devices internally Do not open the laser housing due to potenti
5. 50V 1 6A Slow Blow 20mm Glass Total Power 68W X Y Axis Beam Angle 20 Music Control Audio Sound Activated Laser Classification Class 4 Laser Safety Standard EN60825 1 2007 Condition Temperature 10 40 C DMX Connections 3 pins XLR Male Female DMX Channels Max 13 channels Measurement See picture below N Weight 6 kgs xt j e Es 300 Every information is subject to change without prior notice The availability of particular products may vary by region Please check with the dealer 2
6. C to enter MODE OPTION e Till to DMX address shown on LCD monitor e Press UP DOWN to change the DMX address that you wanted MODE e Press ENTER to confirm the laser OMX ADD 001 to show the present mode at the next operation FUNC UP DOWN ENTER control by DMX signal the DMX indicated LED on front panel is in RED E Attention When the laser is connected with DMX controlled or under e Press FUNC to enter MODE OPTION e Till to SLAVE shown on LCD monitor Connect MASTER and SLAVE lasers with DMX cable The SLAVE lasers are in SLAVE MODE Check XLR Control cable connection section for your reference e Press ENTER to confirm the laser to show the present mode at the next operation 21 USER MANUAL SETTING MODE Press FUNC to enter MODE OPTION Till to SETTING shown on LCD monitor Press UP DOWN to choose MODE You will have COLOR MIRROR MUSIC modes Press ENTER to confirm the mode COLOR MODE SINGLE COLOR single white color show DOUBLE COLOR RGY three color show MULTICOLOR full color show MIRROR MODE Press UP DOWN to change scanned world mirror UP is for Y direction mirror T setting and DOWN is Tor X direction mirror setting X MUSIC MODE To set the sensitivity of SOUND mode ILDA Control Mode This unit has the ILDA DB25 port and it can be controlled by the PC There is auto transform set in the inside of the unit to transform the ILDA and preprogrammed show when connect
7. a SURPASS 7 LASER SHOW SYSTEM SURPASS S 850RGB SURPASS S 1300RGB VERSION SD 2 0 This manual contains important laser system safety and operation information Read and understand all instructions prior to powering on laser unit the first time to avoid laser eye injury and to avoid breaking the law Keep this manual in a safe place for future reference USER MANUAL WARNING DATA Lasers can be hazardous and have unique safety considerations Permanent eye injury and blindness is possible if lasers are used incorrectly Pay close attention to each safety REMARK and WARNING statement in the user manual Read all instructions carefully BEFORE operating this device xxx LL Attention Important N Caution A Laser A Recycle Cam Indoor Y Wastebin y r Location Indicates a skill or other useful information for special situations Indicates important information to protect people from laser incident or damage Prevent damage or injury from incorrect operation Laser safety warming labels To protect the environment recycle packing material wherever possible The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other fluids or metallic objects Don t throw this product away just as general trash please dispose of this product following the
8. al exposure to unsafe levels of laser radiation The laser power levels accessible if the unit is opened can cause instant blindness skin burns and fires USER MANUAL LASER SAFETY AND OPERATING INSTRUCTIONS W STOP AND READ ALL LASER SAFETY DATA W Laser light is different from any other light source witch you may be familiar The light from this product can potentially cause eyes injury if not set up and used properly Laser light is thousands of times more concentrated than light from any other kind of light source This concentration of light power can cause instant eye injuries primarily by burning the retina the light sensitive portion at the back of the eye Even if you can not feel heat from a laser beam it can still potentially injure or blind you or your audience Even very small amounts of laser light are potentially hazardous even at long distances Laser eye injuries can happen quicker than you can blink It is incorrect to think that because these laser entertainment products split the laser into hundreds of beams or laser beam is scanned out in high speed that an individual laser beam is safe for eye exposure This laser product uses dozens of milliwatts of laser power Class 4 levels internally Many of the individual beams are potentially hazardous to the eyes It is also incorrect to assume that because the laser light is moving it is safe This is not true Nor do the laser beams always move Since eye inj
9. als e Do not use laser if the laser appears to be emitting only one or two beams e Do not use laser if housing is damaged or open or if optics appear damaged in any way e Never open the laser housing The high laser power levels inside of the protective housing can start fires burn skin and will cause instant eye injury e Never leave this device running unattended e The operation of a Class 4 laser show laser is only allowed if the show is controlled by a skilled and well trained operator familiar with the data included in this manual e The legal requirements for using laser entertainment products vary from country to country The user is responsible for the legal requirements at the location country of use e Always use appropriate lighting safety cables when hanging lights and effects overhead LASER LIGHT AROVID DIRECT EYE EXPOSURE Further guidelines and safety programs for safe use of lasers can be found in the ANSI 2136 1 Standard For Safe Use of Lasers available from www laserinstitute org Many local governments corporations agencies LASER EXPOSURE WARNING A military and others require all lasers to be used under the guidelines of ANSI Z136 1 Laser Display guidance can be obtained via the International Laser Display Association www laserist org USER MANUAL LASER SAFETY LABEL REPRODUCTIONS _ This is only one laser aperture on this product The label Indicates the laser beam output apertu
10. aser beam will be blank out in 3 seconds without AUDIO MIC activated signal E Attention In preprogrammed standalone MUSIC SHOW mode the SD SHOW mare e Press FUNC to enter MODE OPTION e Press UP DOWN to choose folder the folder name have to be 8 characters including letter or numbers Any folder name with more than 8 characters can not be displaced on LED monitor Press ENTER to choose the folder e Press UP DOWN to choose show mode ILDA single show or PRG preprogrammed show e Press ENTER to confirm the laser to show the present mode at the next peration Nw Save any other files in it SD maximum support 100 folders with less than 255 files in each folder The SD has to be FAT32 format system 4 Attention PRG preprogram show In SD card in folder ANIMATION for example to do the PRG preprogrammed show a TXT file with WINDOW SYSTEM has to be done in the same folder The TXT file has to be renamed to PRG For example 20 USER MANUAL In folder ANIMA folder there are 3 ild file show They are ANIMA 1 ild ANIMA2 ild ANIMA3 ild If you want to do a preprogram show with them you should do the TXT files as ANIMA1 ild 12 3 ANIMA2 ild 20 1 ANIMAS3 ild 18 4 Save this TXT file with name ANIMA TXT change the file name from ANIMA TXT to ANIMA PRG IMPORTANT NOTES ANIMA1 ild is the ild show name 12 is scanner speed 3 is how many times you want this show to repeat DMX MODE e Press FUN
11. d with a terminator Solder a 120 Ohm resistor between Signal and Signal into a 3 pin XLR plug and plug and plug it in the DMX output of the last fixture Ji PINS N R PIN 2 USER MANUAL Building a serial DMX chain lt DMX 512 Controller operation Master slave operation e lf you are using the standard DMxX controllers you can connect the DMxX output of the controller directly with the DMX input of the first fixture in the DMxX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables e Connect the DMX output of the first fixture in the DMX chain with the DMxX input of the next fixture Always connect output with the input of the next fixture until all fixtures are connected e f you use a controller with 5 pins DMX connector you need to use a 5 to 3 pins adpter e At last fixture the DMX cable has to be terminated with a terminator Solder a 120 Ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pins XLR plug and plug it in the DMX output of the last fixture e Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system e The DXM output and input connectors are pas
12. e with an appropriate safety rope Fix the safety rope at the safety rope only The ambient temperature must be between 10 C to 40 C Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons CAUTION Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION If this device will be operated in any way different to the one described in this manual the product may suffer damages and the warranty word USER MANUAL BEFORE OPERATION Unpacking Instructions N CAUTION Immediately upon receiving a fixture carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling Save the package and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing What is included The carton or flight case contain following items Laser Light KEYs for key switch Power Cord Interlock Connector 20m DB25 ILDA Cable USER MANUAL Flight Case
13. in the power plug least Make sure that the power switch is set to off position before you connect the device to the mains The power plug has to be accessed after installing the device e Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time USER MANUAL Always disconnect from the mains when the devise is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord It is essential to connect the yellow green conductor to earth The electric connection repairs and servicing must be carried out by a qualified employee Do not switch the fixture on and off in short intervals as this would reduce the laser diode life For replacement please use fuses of same type and rating only If the device has been exposed to drastic temperature fluctuation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The minimum distance between the fixture and surrounding walls must be more than 50cm Always fix the fixtur
14. ing by the 25 pin cable the unit will be control by PC when disconnect the unit it will be preprogrammed program control In the theory as long as it is ILDA B25 It can control this unit but in the reality some of the software can not control this unit for the 4 pin and the 17 pin of the output card has not connect In fact this is an easy problem As long as you connect them It can control this unit 22 USER MANUAL DMX Channels Chart Several optional operating modes were preprogrammed set into this laser projector at DMX channel 1 Before control other DMX channels please be sure that the channel 1 was set in proper mode value DMX CHANNEL 1 CHART CHANNEL VALUE FUNCTION 000 073 Laser Block Out 074 110 PRG show in SD card 111 147 ILD show in SD card PRG or ILD mode CHANNEL VALUE DESCRIPTION 000 255 Shows PRG or ILD DMX PATTERN MODE CHANNEL VALUE FUNCTION CH 2 000 255 86 Patterns as shown in PATTERN LIST PATTERN 23 USER MANUAL 000 010 NO strobing CH 3 011 199 Strobing from slow to fast Strobe 200 255 Strobing to Sound 000 125 X position 126 185 Moving from slow to fast CH4 Moving with random speed X Moving Random position 246 255 Sound to random position 000 125 Y position 126 185 Moving from slow to fast CH5 186 225 Moving with random speed Y Moving 226 245 Random position 246 255 Sound to random position 000 010 Original size CH6 Zooming
15. or any unauthorized modification to the device Features e STABLE TE COOLED LASER DIODE CNI e HIGH SPEED 40KHz SCANNER e 2xAUTO SHOW 2 x MUSIC SHOW e 86 ANIMATED GRAPHIC SHOW PATTERNS e HUNDRES PREPROGRAMED BEAM EFFECT e MULTIMODE REAL WAVE EFFECT e PERFECT WHITE COLOR BALANCE e LCD CONTROL MONITOR e SMART PRESS BUTTON CONTROL PANEL e AUTO SELF CHECKING SYSTEM e AUTO SOUND DMX amp ILDA e 2DMX MODES amp 13DMX CHANNELS e AUTO DETECTED ILDA SIGNAL INTERFACE e EXACTLY 3D ADJUSTABL COLOR MIXER e KEY SWITCH amp INTERLOCK e 100 LASER SAFETY REGULATION e BEAM WAVE TEXT ANIMATION LOGO USER MANUAL Front Panel Noj name f FUNCTION 2 tee a 2 ae teem pores sommes E T REE DET BRACKET and a mounting hole to fix a mounting hook USER MANUAL Rear Panel o we Ce ee oe lt eas OK Paes BTT DIET DHE OCE ee ET OC oem reman 15 USER MANUAL ILDA Hardware Setting Panel LCD MONITOR 0 FUNC DOWN ENTER eooo0o0o0oo000eo eooo000000000 Size No NAME FUNCTION 16 MUSIC Turn the knob to adjust the audio respond sensitivity X SIZE The The Size of X axis adjustment of X axis The Size of X axis adjustment a Y SIZE The Size of Y axis adjustment 19 ILDA THROUGH Standard ILDA DB25 Output through 20 ILDA INPUT Standard ILDA DB25 Input ILDA DB25 Standard ILDA DB25 In
16. put ILDA ILDA connection indicator LED Red is connection and green is disconnection snag Laser beam output indicator LED MIC Microphone Turn the knob to adjust the sound activated sensitivity 24 LCD control Panel LCD control Panel Panel Intelligent LCD control panel of the system Intelligent LCD control panel of the system control panel of the system USER MANUAL Y IMPORTANT Y For your own safely and full laser safety Regulation we do strongly recommend You to take this optional switch CONTROL amp FUNCTION e Regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use e Do not switch the unit on and off in short time intervals e Always unplug the unit when it is not used for a longer time Or before replacing the bulb or start servicing e Inthe event of serious operation problems stop using the fixture and contact your dealer immediately AA SAAR ES mais i Attention Laser Safety Scanner Board is included in the system The Laser light will be turned off when the scanned angle is less than 1 degree Operating Mode Xxxx ax Foreros Attention Once after every power on laser the VERSION and MANUFACTURE INFORMATION will be shown in LCD monitor of rear panel When laser is powered on LCD monitor on rear panel shows the current operating standalone mode or DMX address of DMX mode With help of LCD control panel is very easy to se
17. re Caution Class 4 LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM LASER EMISSION DATA Divergence total light lt 40 degrees Cooling TEC amp Fan Cooling Scanning ILDA Standard 20Kpps AS measured under IEC measurement conditions for classification USER MANUAL LASER COMPLIANCE STATEMENT This laser product complies with EN IEC 60825 1 Ed 2 2007 03 GENERAL SAFETY INSTRUCTIONS Every person involved with installation and maintenance of this device have to e Be qualified e Follow the instructions of this manual CAUTION Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has left out premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Y Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device e Please consider that damages caused by manual modifications to the devise are not subject to warranty e Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution e Make sure that the available voltage is not higher than stated on the rear panel e Always plug
18. s through to maintain the DMX circuit when power is disconnected to the unit e Each fixture needs to have a DMX address to receive the data from the controller The DMX address number which could be read from rear panel of each fixture is between 000 511 e The end of the DMX 512 chain should be terminated to reduce signal errors USER MANUAL Proper Laser Set Up amp Usage This fixture has been designed to be hung It is recommended for safety purposes your lighting effect are properly mounted using a suitable hanging clamp and safety cable Items appropriate for safe and effective mounting are easily sourced from your lighting vendor International laser safety regulations require that lasers must be operated in the fashion illustrated below with a minimum of 3 meters 9 8 ft of vertical separation between the floor and the lowest laser light vertically Additionally 2 5 meters of horizontal separation is required between laser light and audience or other public spaces 3 Meters CAUTION Use of contro kR adjustments or performance of procedures other than what is specified herein may result in hazardous radiation exposure USER MANUAL Rigging the Fixture CAUTION Please consider the respective national norms during the installation The installation must only be carried out by an authorized employee or dealers e The installation of the fixture has to be built and constructed in a way that it can hold
19. t and change the operating mode of laser After every resetting and saved the new mode information will be shown on LCD monitor at next power on FUNC Mode Option to choose the operating mode of laser Confirmation to confirm the laser to show the present mode at the m NTE A next operation UP UP DOWN to change operating mode parameter or DMX address OPERATION MODE UP MODE UP MODE UP MODE DOWN DOWN DOWN AUTO SHOW 1 AUTO SHOW 2 gt MUSIC SHOW 1 MUSIC SHOW 2 we ENTER MODE SD SHOW uP MODE ENTER MODE DOWN iii mE HHRHH l K sp PRG SHOW gt PRG PIATE UP DOWN MODE L MODE L FUNC ENTER S SD ILD SHOW ILD AAA AA AK MODE UP MODE DOWN ENTER DMX ADD 001 l DMX ADD 512 FUNC SLAVE FUNC MODE SETTING UP MODE SETTING UP DOWN DOWN COLOR _ MIRROR MODE ENTER ENTER ENTER ENTER MODE SETTING MODE SETTING MODE SETTING SINGLE COLOR MIRROR SYN SX N music E MODE SETTING c v UP DOUBLECOLOR DOWN DOWN DOWN MODE SETTING MODE SETTING MULTICOLOR MIRROR SY Y SX Y ENTER ENTER 18 USER MANUAL AUTO SHOW 1 e Press FUNC to enter MODE OPTION e Till to AUTO SHOW 1 shown on LCD monitor The laser is set at AUTO SHOW 1 standalone mode and it will play the preprogrammed show until next setting is changed AUTO SHOW 1 is fast and hot show which is be
20. tter for DISCO MODE e Press ENTER to confirm the laser to AUTO SHOW 7 show the present mode at the next operation FUNC UP DOWN ENTER AUTO SHOW 2 e Press FUNC to enter MODE OPTION e Till to AUTO SHOW 2 shown on LCD monitor The laser is set at AUTO SHOW 2 standalone mode and it will play the preprogrammed show until next setting is changed AUTO SHOW 2 is slow and soft show which is better for MUSIC BAR e Press ENTER to confirm the laser to MODE AUTO SHOW 2 show the present mode at the next operation FUNC UP DOWN ENTER MUSIC SHOW 1 SC e Press FUNC to enter MODE OPTION MODE e Till to MUSIC SHOW 1 shown on LCD MUSIC SHOW 1 monitor The laser is set at MUSIC SHOW 1 l FUNC UP DOWN ENTER standalone mode and it will play the preprogrammed show until next setting is changed MUSIC SHOW 1 is fast and hot show which is better for DISCO e Press ENTER to confirm the laser to show the present mode at the next operation USER MANUAL MUSIC SHOW 2 SOU e Press FUNC to enter MODE OPTION MODE e Till to MUSIC SHOW 2 shown on LCD MUSIC SHOW 2 monitor The laser is set at MUSIC SHOW 2 ae 06 cal ions standalone mode and it will play the preprogrammed show until next setting is changed MUSIC SHOW 2 is slow and soft show which is better for MUSIC BAR e Press ENTER to confirm the laser to show the present mode at the next operation l
21. uries can occur instantly it is critical to prevent the possibility of any direct eye exposure In the laser safety regulation it is not legal to aim Class 4 lasers in areas which people can get exposed This is true even if it is aimed below people s faces such as on a dance floor e Do not operate laser without first reading and understanding all safety and technical data in this manual e Always set up and install all laser effects so that all laser light is at least 3 meters 9 8 feet above the floor on which people can stand See Proper Laser Set up amp Usage section later in this manual 3 USER MANUAL e After set up and prior to public use test laser to ensure proper function Do not use if any defect is detected Do not use if laser emits only one or two laser beams rather than dozens hundreds as this could indicate damage to the diffraction grating optic and could allow emission of higher laser levels e Do not point lasers at people or animals e Never look into the laser aperture or laser beams e Do not point lasers in areas in which people can potentially get exposed such as uncontrolled balconies etc e Do not point lasers at highly reflective surfaces such as windows mirrors and shiny metal Even laser reflections can be hazardous e Never point a laser at aircraft this is a federal offense e Never point un terminated laser beams into the sky e Do not expose the output optic aperture to cleaning chemic
Download Pdf Manuals
Related Search