Home

Telecom FM Dataroute Voice Manual

1. If there are no problem in the above items the line and the device should be working Problems may be caused by your computer configuration or device configuration Check Your Configuration 1 Enter the device manager to check if Ethernet adapter is correctly installed If any problem exists please re install it 2 Check the configuration of Ethernet adapter in PC Try to manually set IP address that is in band 192 168 1 X without conflict 3 Try to run command ping 192 168 1 1 in a command prompt Start Programs Accessories Command Prompt If the response returns time out please check Ethernet connection and IP settings 4 If the DataRoute voice is reachable try to ping a known internet IP e g a DNS server ping 4 2 2 2 If ping is reachable there are no problems in the DataRoute voice Please go to step 5 If ping is not reachable see step 6 and check if the configuration is correct 5 Please try to ping a internet URL e g ping www google com If ping is reachable there are problems in the network settings Please check the settings of the PC terminal e g whether the security level is too high or whether anti virus or firewall is installed If ping is not reachable check the DNS setting of Ethernet adapter 54 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LEIECOM Fv Note 1 The precondition is that LAN se
2. Remove Click Add to do the configuration after choosing a domain list type Then set the domain address and port number in the next interface Click Apply Save to add the entry to the domain filter Parental Control domain Add Enter the domain address and port number then click Apply Save to add the entry to the domain filter domain Address Apply Save 41 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 11 4 MAC Filters Please go to path Firewall gt MAC Filters page to setup MAC filtering All MAC layer frames will be forwarded except those matching with any of the specified rules in the settings MAC Filtering Setup All MAC layer frames will be FORWARDED except those matching with any of the specified rules in the following table Choose Add or Remove to configure MAC filtering rules Tepes MAC address Remove Add Remove Please click Add to create a filter to identify the MAC layer frames by specifying at least one condition If multiple conditions are specified all of them will take effect Click Apply to save and activate the filter Add MAC Filter Create a filter to identify the MAC layer frames by specifying at least one condition below If multiple conditions are specified all of them take effect Click Apply to save and activate the filter Protocol Type v Source MAC Address eg 00 90 96 01 2A
3. SSID1 Enable LAN DHCP Fill in the required information and click the Apply Save button For most networks it is only required to set the correct APN value leave the other settings on default values If your network requires login enter the valid PPP Username and PPP Password 20 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng LIECOM Fw 7 2 ADSL Configuration WAN Service Please go to path Network gt WAN Service page Then do the following to setup an ADSL connection 1 Click Add button to start the ADSL network wizard ATM PVC Configuration This screen allows you to configure an ATM PVC identifier VPI and VCI Notice If the link type is EoA it can use the PVC repeatedly though it is existent But the PPPoA or IPoA can t VPI 0 255 0 VCI 32 65535 35 Back Next Enter the values for VPI and VCI supplied by the ADSL Service Provider 2 Click Next to select the DSL link type and Encapsulation Mode supplied by the ADSL service provider note please choose EoA for PPPoE connection ATM PVC Configuration Select a service categoryS Otherwise choose an existing interface by selecting the checkbox to enable it Select DSL Link Type EoA is for PPPoE IPoE and Bridge Sg EoA PPPoA IPOA Encapsulation Mode LLC SNAP BRIDGING Service Category UBR WithoutPCR Enable VLAN Enable Quality Of Service Enabling pack
4. e Tunnel Name specify a name to identify the tunnel e Ip Address or Domain Name specify the IP Address or FQDN for the remote PPTP Network Server e PNS Username specify the username required to login to the remote PPTP Network Server e PNS Password specify the password required to login to the remote PPTP Network Server e Enable set to use to start using the PPTP tunnel e Use Default Gateway On the Remote Network set to yes to forward traffic to the remote gateway e Authentication Method select the authentication method required to login to the PNS PAP CHAP MSCHAP or set to AUTO for the authentication method to be determined automatically e Use Static IP Address select to specify the IP Address manually Set the required options and then click the Apply button 32 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 9 Wireless WLAN 9 1 WLAN Basic Go to path WLAN gt WLAN Basic WLAN Basic Settings Enable WLAN C Disable SSID broadcast BSSID 00 14 49 B83 04 6E Max chent number Channel Current channel 1 Auto Channel Timer min lo sd Apply Save e Enable WLAN select to enable the built in Wi Fi access point e Disable SSID broadcast select to prevent the Access Point from being discoverable Users will need to manually specify the SSID to connect e SSID enter the SSID to identify the Wi Fi access point thi
5. 3B Save Apply 42 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wp DataRoute voice User Manual LCLECOM Ew 11 5 Access Control Remote Access The Access Control feature allows ports to be opened to the internet WAN connections so that it is possible to connect remotely to the DataRoute voice Go to path Firewall gt Access Control Access Control Services A Service Control List SCL enables or disables services from being used Only the service of WAN is Enabled the WAN Port can be configed effectively Services LAN WAN WAN Port HTTP Enable Enable 80 ICMP Enable Enable TELNET Enable Enable TFTP Enable Enable 69 Oh Kl on LJ Save Apply To enable remote access to the DataRoute voice web interface check the Enable box under WAN for the HTTP service The default port is the standard web port 80 which can be changed by entering a new value under WAN Port Once enabled it will be possible to access the web interface by browing to the Internet IP Address assigned to the DataRoute voice For example if the IP address assigned by the ISP is 80 70 60 50 and the WAN Port is set to 8080 the following would be entered into the web browser http 80 70 60 50 8080 Note It is strongly recommended that the web interface password be changed go to path Tools gt Access Control before enabling the Access Control feature This feature can b
6. 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew Step 3 Wireless Settings Enable WLAN Disable SSID broadcast SSID DATAROUTE BSSID 00 14 49 B3 04 6E Max chent number Channel Auto Channel Timer min los By default the Wireless Wi Fi access point is enabled and the SSID the name that is displayed when users search for Wi Fi networks is set to DataRoute To keep the default settings click Next to go to the next step To change the SSID 1 Enter the new SSID in the SSID box 2 Select the correct Country 3 Click the Next button 14 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw Step 4 Local Area Network Setup IP Address 192 168 1 1 Subnet Mask 255 255 255 0 Enable IGMP Snooping Disable DHCP Server Enable DHCP Server Start IP Address End IP Address Leased Time hour 24 0 O Static DNS Server Get DNS Server From WAN L configure the second IP Address and Subnet Mask for LAN interface By default the DataRoute voice has an IP Address of 192 168 1 1 and the DHCP server is enabled so that IP addresses will be automatically assigned to clients connecting to either the wired ethernet ports or via Wi Fi To keep the default settings click Next to go to the next step A new IP address can be assigned to the DataRoute voice and the DHCP options can be changed from this sc
7. WPS 3G D OO OO OO OO OO a lt d Right Side Interfaces U Power LAN 1 LAN 2 LAN 3 LAN 4 Phone ADSL d Left Side Interfaces P Reset WPS SS O o SIM 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew Label Solid green DataRoute Power on Solid red Firmware update in progress Off DataRoute Power off On Ethernet is connected Blinking green Ethernet Traffic flows Off Ethernet is disconnected Blinking green PPP DHCP negotiation Solid green PPP DHCP up Quick blinking green Tx Rx traffic on line On Modem synchronized to the DSLAM Quick blinking green Modem training but not synchronized Slow blinking green Modem Idle On The analogue phone connected to Phone port off hook Off The analogue phone connected to Phone port on hook On Wi Fi connection is available Blinking green Negotiation or traffic on line Off Wi Fi connection is not available On WPS connection setup successfully WPS Blinking WPS connection has been activated Off WPS connection is not activated Blinking green Negotiation or traffic on line Solid green Up Quick blinking green Tx Rx traffic on line Solid red Authentication failed Off Traffic through DSL interface Power switch For 12V DC power adapter LAN interface for connecting to computers Connecti
8. address for a DNS server to pass to DHCP clients By default this is set to the IP address of the DataRoute voice to use the built in DNS server recommended Get DNS Server from WAN select to pass the DNS server addresses obtained automatically from the WAN interface to the DHCP clients Configure the second IP address select to assign an additional IP address to the DataRoute voice advanced option Notes 1 When you use the DHCP Server please make sure you don t have multiple DHCP Servers in one LAN 2 To view a list of clients that have been assigned addresses by the DHCP server go to the path DHCP gt Assigned Leases 3 To reserve an IP address within the DHCP range for a client so that the client always receives the same IP address go to the path DHCP gt Static Leases Click the Add Static Lease button and enter the MAC address and required IP Address for the client Make sure that the IP address chosen is within the range entered on the LAN Setup page 38 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 11 Firewall 11 1 Firewall Settings Please go to path Firewall gt Firewall Settings page check Enable to activate Global firewall settings then click Apply Save Note three Firewall levels are supported in the device they are Low enable basic firewall features prevent port scanning allow PING from WAN side
9. from the Intemet can be useful some files can potentially ham your computer f you do not trust the source do not open or save this file What s the isk 13 4 Update Restore Settings Please go to path Tools gt Update Settings page Click Browse button to choose a configuration file then click Update Settings to restore configuration Tools Update Settings Update Broadband Router settings You may update your router settings using your saved files Settings File Name Browse Update Settings 50 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wp DataRoute voice User Manual LCLECOM Ew 13 5 Update Software Please go to path Tools gt Update Software page Click Browse to choose the right software Then click Update Software to update The power LED will go red to indicate that the software upgrade is in progress Once complete the unit will automatically restart with the new software The current software version can be viewed by going to path Status gt Basic Info Attention please make sure the power to the device is not interrupted during the software updating process Also the RJ45 cable should be connected tightly between the PC and device during the software uploading process Once updated please press the reset button or go to path Tools gt Factory Settings to restore the device to the new factory default settings if necessary Update Software St
10. other client to the DataRoute voice via Wi Fi 9 3 Advanced Settings Go to path WLAN gt Advanced Settings This page contains Advanced parameters for the Wireless LAN interface It is strongly recommended that these settings be left unchanged unless there is a specific requirement for different settings in the environment where the DataRoute voice is installed Altering these parameters may result in a reduction in Wireless performance 34 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LELECOM Ew 9 4 WLAN MAC Filters Go to path WLAN gt WLAN MAC Filters Wireless MAC Filter MAC Restrict Mode Disabled Allow Deny MAC Address Remove This page can be used to restrict the clients that are permitted to connect Wirelessly to the DataRoute voice WARNING Changing the mode takes immediate effect and so may disconnect any connected Wireless clients MAC Restrict Mode select from the following e Disabled all MAC Addresses will be allowed to connect e Allow only MAC addresses listed below will be allowed to connect e Deny all MAC Addresses will be allowed to connect EXCEPT those listed below Use the Add button to add MAC addresses to the list 35 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 9 5 WLAN Bridge Go to path WLAN gt WLAN Bridge
11. Bridge Restrict Enabled w Refresh Apply Save Use this page to configure Wireless Bridging functionality Wireless Bridging allows a Wi Fi network to be extended to cover a larger area through the use of multiple Wi Fi bridge devices AP Mode e Access Point DataRoute voice can be used as both a Wireless Access Point and a Wireless Bridge default e Wireless Bridge DataRoute voice can be used as a Wireless Bridge only Bridge Restrict e Enabled only Wireless Bridges whose MAC Addresses are entered below may connect e Disabled any Wireless Bridge may connect Remote Bridges MAC Address enter MAC Addresses for remote bridges which are permitted to connect when Bridge Restrict option is enabled Enter the required settings and then click the Apply Save button 36 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 10 LAN DHCP Configure the DataRoute voice s IP address and DHCP options Go to path DHCP gt LAN Setup Local Area Network LAN Setup Configure the Broadband Router IP Address and Subnet Mask for LAN interface GroupName Default IP Address 192 168 1 1 Subnet Mask 255 255 255 0 L Enable IGMP Snooping Disable DHCP Server Gi Enable DHCP Server Start IP Address 192 168 1 2 End IP Address 192 168 1 254 Static DNS Server 192 168 1 1 O Get DNS Server From WAN L configure t
12. Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 4 2 Computer Configuration The default IP address for DataRoute voice is 192 168 1 1 The Subnet Mask is 255 255 255 0 Devices can be connected via one of the Ethernet ports or via Wi Fi The default Wi Fi settings are Wireless SSID DATAROUTE Wireless Key data1234 Users can configure the DataRoute voice through a web browser The DataRoute voice can be used as a gateway DNS server and DHCP server by default the DataRoute voice will automatically assign an IP address to any devices connecting to it alternatively users can set the computer s TCP IP settings manually as follows 1 Set the computer IP address to the same subnet as the DataRoute voice i e set the IP address of the PC to one in the range of 192 168 1 2 192 168 1 254 excluding 192 168 1 1 2 Set the computer s gateway address to the IP address of the DataRoute voice 3 Set the computer s Primary DNS server to the IP address of the DataRoute voice or to that of an effective DNS server 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng LIECOM Fw 4 3 Log In Start the web browser and enter the following in the address bar http 192 168 1 1 The authentication interface will pop up as below Windows Security Coxe The server 192 168 1 1 at 3G Wireless Gateway
13. PP Password Po PPPoE Service Name Ir Authentication Method Enable Fullcone NAT Dial on demand with idle timeout timer Use Static IPv4 Address Enable PPP Debug Mode Oooo Bridge PPPoE Frames Between WAN and Local Ports Multicast Proxy Enable IGMP Multicast Proxy Enter the username and password provided by the ADSL service provider select any other options required and click Next WAN Setup Summary Make sure that the settings below match the settings provided by your ISP PORT VPI f VCI 0 0 35 Connection Type PPPoE Service Name pppoe_0_0_35 Service Category UBR IP Address Automatically Assigned Service State Enabled NAT Enabled Full Cone NAT Enabled Firewall Enabled IGMP Multicast Disabled Quality Of Service Disabled Click Apply Save to have this interface to be effective Click Back to make any modifications Back Apply Save Check the Summary screen and then click Apply Save to enable the connection The Quick Setup wizard is now complete Refer to the following sections for a complete description of all of the available options 18 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LELECOM Ew 7 Network 7 1 3G Configuration WAN Device WAN Service Note please power off the Gateway before inserting the SIM card Please go to path Network gt WAN Device page When both ADSL and 3G co
14. _AMR_12K we Authentication Name the username which is provided by the SIP provider Password the password which is provided by the SIP provider Preferred codec list select the order of the audio codecs to be used Once the configuration is complete click the Apply button to save changes Click Stop SIP client and then click Start SIP client to enable the configuration 45 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 DataRoute voice User Heng LIECOM Fw 12 3 Advanced Settings Go to path VoIP gt Advanced Settings page to configure the advanced VoIP features Voice SIP Advanced Configuration Echo Cancellation Call Waiting Call Forwarding Number Forward Unconditionally Forward on Busy id 5 R Ge anonymous categ JE O nn Echo Cancellation select to enable the built in echo canceller Call forwarding Number set a number to use call forwarding Select the conditions to use call forwarding by ticking the required boxes MWI select to enable MWI Message Waiting Indicator support Call Barring select to enable Call Barring Anonymous Call Blocking select to disallow incoming calls with no CLI Anonymous Calling select to withhold CLI on outgoing calls DND select to enable DND Do Not Disturb support Silence Suppression when selected audio packets will not be transmitted to the network if no audio is detected to reduce bandwidth usage CNG select t
15. ac ccceeeceseeecesscecueececessccesececessceeueeseceeeccesececesse ce ueecuseeseceseueeen 44 12 3 Advanced Gettngde cece eee e eee e eee e ee ee EEE S Dee RENE SEES SSSR EERE EEE E EEE 46 KC ffe e 1 E 48 13 1 Account Settings Uergel ee EEN EEN EEN EEN EEN 48 DZ SIN EE 49 13523 BACK SOCIO EE 50 13 4 Update Restore SettingS EEN EEN EEN EEN EEN 50 to Update SOW a E 51 e PACO EE 51 ge ee e fl ROULE ae ener reer rrr TTT TTT TTT TTT TT TTT TTT TTT rrr rrr rrr rrr TTT rrr rrr rrr rrr i 51 Do RRO GO CCN ee 52 SC A7 PAOR nee E SE ike Ze ko de Biet de ee 53 14 Troubleshooting EEN 54 AAA Unabl to Access LCST GU suena eee 54 4 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 2 Overview The DataRoute voice is a high speed gateway with functions including e Build in wireless module with speed up to 7 2Mbps e ADSL2 2 modem for broadband connection e Four 10 100M auto sensing Ethernet ports for wired connections e Built in 802 11n enhanced WLAN complies with IEEE 802 11n draft v2 0 and backward to 802 11b g specifications It supports 2x2 MIMO and up to 300Mbps of bandwidth The throughput of WLAN to LAN is more than 100Mbps e Integrated FXS port for voice calls e Supports TR 069 remote management 3 Specification 3 1 Indicators amp Interfaces Front Panel Indicators g N Power LAN 1 LAN 2 LAN 3 LAN 4 Internet ADSL Phone WiFi
16. ailable 3G Link Notice 3G Link UP Notice Enable Apply Save Enter the Mobile Number to send the SMS to and click the Apply Save button 53 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 14 Troubleshooting 14 1 Unable to Access Internet Check the Line and the Device 1 Check the power supply indicator is on if not make sure the connection to the power Supply is correct Make sure the power switch is turned on 2 Check the LAN indicator for the PC is on if not check the cable connection between the PC and the DataRoute voice Make sure that the correct cable is used 3 Check the ADSL LED to see if it is flashing If no fast flashing is observed within 3 minutes please check whether phone line has been correctly connected check whether ADSL filter is correctly used If multiple extensions have been installed make sure that the filter is installed prior to the junction box of the phone line If the above items are confirmed and still no fast flashing of DSL LED is observed call the ISP to query whether ADSL service has been provided on your line 4 Check the ADSL LED to see whether it is unable to change status from fast flashing to always on or whether it changes status to fast flashing after some time of being always on If these phenomena occur constantly please contact your ISP with a request to check lines and signal quality
17. allow ICMP redirect messages from WAN side Middle in addition to Low level prevent ICMP redirect messages High in addition to Middle level prevent SYN Flood attack against PING from WAN side Firewall Settings Global firewall settings Enable Firewall level Low Note by default the Firewall is enabled and set to the High setting it is recommended that to maintain maximum security this setting is not changed 11 2 IP Filters When the firewall is enabled on a WAN or LAN interface all incoming IP traffic is BLOCKED However some IP traffic can be ACCEPTED by setting up filters Please go to path Firewall gt IP Filters gt Incoming IP Filtering Setup Incoming IP Filtering Setup When the firewall is enabled on a WAN or LAN interface all incoming IP traffic is BLOCKED However some IP traffic can be ACCEPTED by setting up filters Choose Add or Remove to configure incoming IP filters Filter Name Interfaces IP Version Protocol SrcIP PrefixLength SrcPort DstIP PrefixLength DstPort Remove Remove 39 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng LIECOM Fw Click Add button to configure incoming IP filters The following interface allows user to create a filter rule to identify incoming IP traffic by specifying a new filter name and at least one condition All of the specified conditions in this filter rule must be satisfied f
18. atus Disable v Specify Classification Criteria A blank criterion indicates it is not used for classification Class Interface LAN Ether Type v Source MAC Address Source MAC Mask Destination MAC Address Destination MAC Mask 29 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 8 Application 8 1 UPnP Settings Go to path Application gt UPnP UPnP Settings Enable UPnP Apply Save Use this page to enable or disable Universal Plug and Play UPnP functionality UPnP allows networked devices to automatically discover each other By default UPnP is enabled it is recommended that this setting be left unchanged 8 2 Dynamic DNS Go to path Application gt Dynamic DNS Dynamic DNS The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname in any of the many domains allowing your Broadband Router to be more easily accessed from various locations on the Internet Choose Add or Remove to configure Dynamic DNS Hostname Username Service Interface Remove Dynamic DNS allows a static hostname to be assigned to a connection which is not assigned a static IP address A subscription to a Dynamic DNS provider is required to maintain the mapping between the hostname and the currently assigned IP address DataRoute voice can work with either the DynDNS or TZO dynamic DNS services Click the Add button an
19. by the layer2 interface Note For SP scheduling queues assigned to the same layer interface shall have unique precedence Lower precedence value implies higher priority for this queue relative to others Click Apply Save to save and activate the queue Name Enable Disable e Interface v Apply Save 28 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng LIECOM Fw Please click QoS Class button to enter QoS Classification Setup page then click Add button to configure network traffic classes This screen creates a traffic class rule to classify the upstream traffic assign queue which defines the precedence and the interface and optionally overwrite the IP header DSCP byte A rule consists of a class name and at least one condition All of the specified conditions in this classification rule must be satisfied for the rule to take effect Click Apply Save to save and activate the rule Add Network Traffic Class Rule The screen creates a traffic class rule to classify the upstream traffic assign queue which defines the precedence and the interface and optionally overwrite the IP header DSCP byte A rule consists of a class name and at least one condition below All of the specified conditions in this classification rule must be satisfied for the rule to take effect Click Apply Save to save and activate the rule Traffic Class Name Rule Order Last v Rule St
20. d enter the current SIM pin and click the Apply Save button The PIN State shows whether the SIM PIN function is currently enabled or disabled The Residual allowed try time shows how many attempts to enter a correct PIN remain if the incorrect PIN is entered too many times a PUK code will then be required for the SIM before it can be used again 24 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 7 4 Advanced ADSL Settings Go to page Network gt ADSL Settings DSL Settings Select the modulation below G Dmt Enabled G lite Enabled 71 413 Enabled ADSL Enabled AnnexL Enabled ADSL2 Enabled TT AnnexM Enabled Select the phone line pair below Inner pair Outer pair Capability Bitswap Enable C SRA Enable Apply Save This page allows advanced settings for the ADSL interface to be adjusted It is recommended that these settings are unchanged from their default values unless instructed by the ISP 7 5 DMZ Host Go to page Network gt DMZ Host NAT DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer Enter the computer s IP address and click Apply to activate the DMZ host Clear the IP address fleld and click Apply to deactivate the DMZ host Save Apply This page allows an IP A
21. d then enter the details provided by the dynamic DNS service provider 30 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 Sac telecoMem DataRoute voice User Manual 8 3 VPN IPSec VPN Go to path Application gt IPSec VPN IPSec Tunnel Mode Connections Add remove or enable disable IPSec tunnel connections from this page Connection Name Remote Gateway Local Addresses Remote Addresses Remove Edit Add New Connection A Virtual Private Network VPN Tunnel can be established to provide secure communications between 2 points on the internet using the IPSec tunneling protocol Click the Add New Connection button to display the IPSec Settings IPSec Settings IPSec Connection Name Remote IPSec Gateway Address IP or Domain Tunnel access from local IP addresses IP Address for VPN IP Subnetmask 255 255 255 0 Tunnel access from remote IP addresses IP Address for VPN IP Subnetmask 255 255 255 0 Key Exchange Method Authentication Method Pre Shared Key Perfect Forward Secrecy Show Advanced Settings Advanced IKE Settings Show Advanced Settings e IPSec Connection Name specify a name to identify the tunnel e Remote IPSec Gateway Address specify the IP address or FQDN for the remote end of the tunnel this should be the internet IP address for the remote gateway e Tunnel access from local IP addresses specify the IP address or subnet for the local side of the IPSec tunnel
22. ddress to be entered where all incoming traffic from the WAN interfaces will be routed Note that the Virtual Servers options take precedence all traffic that does not match any application configured in Virtual Servers will be forwarded to the DMZ Host IP Address Enter the required IP Address and clickt the Save Apply button 25 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 7 6 Port Forwarding Virtual Servers Go to path Network gt Virtual Servers NAT Virtual Servers Setup Virtual Server allows you to direct incoming traffic from WAN side identified by Protocol and External port to the Internal server with private IP address on the LAN side The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side 4 maximum 32 entries can be configured Server External External HEET Internal Internal Server IP WAN a Name Port Start Port End i Port Start Port End Address Interface This page allows the user to forward incoming traffic on selected ports on the WAN interfaces to internal hosts This can be used to make internal applications available to the internet e g a web server Click the Add button to add a new forward NAT Virtual Servers Select the service name and enter the server IP address and click Apply Save to forward IP packets for this serv
23. e Tunnel access from remote IP addresses specify the IP address or subnet for the remote side of the IPSec tunnel e Key Exchange Method select Auto to use the standard Internet Key Exchange IKE method or Manual to specify the encryption and authentication keys manually e Authentication Method only Pre Shared Key is supported e Pre Shared Key enter the Pre Shared Key e Perfect Forward Secrecy select whether to use the Perfect Forward Secrecy PFS method Fill in the required options and then click the Apply Save button 31 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 8 4 VPN PPTP Config Go to path Application gt PPTP Config PPTP Config Choose Edit to modify information over PPTP WAN Service Note If the table below is empty please add WAN Service first Click Here Ip EES Tunnel Name Address Domain WAN Enable Leili use Lhc Status Edit Action Interface Gateway Gateway Name 1_VOIP_INTERNET_R_orangeinternet null ppptd3g NO null NO Unconfigured A default PPTP tunnel is automatically created for each available WAN interface Click the Edit button to configure the tunnel PPTP Edit Tunnel Name 1 VOIP_INTERNET Ko Ip Address or Domain Name Po WAN Interface ppptd3g0 PNS Username Enable AUTO Use Default Gateway On The Remote Network Authentication Method wi Use Static IP Address
24. e used via an ADSL or 3G connection Note that some 3G networks have internal NAT and Firewall systems which do not allow remote access 43 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wp DataRoute voice User Manual LCLECOM Ew 12 Voice VoIP 12 1 Voice Configuration Connect a normal analogue telephone to the Phone port Phone calls can be made over the GSM 3G network when a valid SIM is inserted and using Voice over IP when there is an active connection to the internet By default all calls are dialled over the GSM 3G network To make calls via VoIP SIP it is necessary to configure a connection to a SIP Service Provider 12 2 Basic Settings Go to path VoIP gt Basic Settings page then click on the Service Provider O tab Enter SIP parameters and click Apply to save the parameters Global Parameters Service Provider 0 Voice SIP Configuration Enter the SIP parameters and click Start Stop to save the parameters and start stop the voice application Locale Selection USA NORTHAMERICA ei Note Requires vodsl restart to take affect Voip Dialplan Setting 9x T 9x Use SIP Proxy SIP Proxy Port Use SIP Outbound Proxy SIP Outbound Proxy Port 5060 Lise SIP Registrar SIP Registrar Port 5060 Locale selection choose the Location this will set the local tones etc heard on the phone SIP Domain Name enter the SIP Domain provided by the SIP Prov
25. emand has been selected with a tick If it is selected the connection is activated only when traffic to the internet arrives Make sure that the above parameters are saved after configuration 55 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299
26. ep 1 Obtain an updated software image file from your ISP Step 2 Enter the path to the image file location in the box below or click the Browse button to locate the image file Step 3 Click the Update Software button once to upload the new image file NOTE The update process takes about 2 minutes to complete and your DSL Router will reboot Software File Name Browse Update Software 13 6 Factory Settings To restore the DataRoute voice to the factory default configuration either press the Reset button on the side of the unit or go to path Tools gt Factory Settings and click the Restore Default Settings button Note all user entered configuration options will be lost 13 7 Reboot Router To perform a soft restart of the DataRoute voice go to path Tools gt Reboot Router and click the Reboot button A restart takes approximately 2 minutes 51 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 13 8 TR 069 Client The DataRoute voice can be provisioned remotely via the use of a TR 069 remote management server Please go to path Tools gt TR 069 Client page to setup an auto configuration server to perform auto configuration provision collection and diagnostics to this device Select the desired values and click Apply Save to configure the TR 069 client options Note all the parameters in the screenshot should be matched wit
27. et level QoS for a PVC improves performance for selected classes of applications QoS cannot be set for CBR and Realtime VBR QoS consumes system resources therefore the number of PVCs will be reduced Use Advanced Setup Quality of Service to assign priorities for the applications Enable Quality Of Service Back Next 21 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng LIECOM Fw 3 Click Next if EoA link type was selected choose the WAN service type normally PPP over Ethernet PPPoE WAN Service Configuration Select WAN service type PPP over Ethernet PPPoE O IP over Ethernet Bridging Enter Service Description pppoe_0_0_35 Port Bind LANI LANZ LAN LAN4 SS5ID1 _ SSID2 _ SSID3 SSID4 Back Next 4 Click Next to input the username and password provided by the ADSL service provider select any other options required PPP Username PPP Password PPPoE Service Name Authentication Method AUTO we Enable Fullcone NAT Enable Firewall Use Static IPv4 Address NI Dial on demand with idle timeout timer m Enable PPP Debug Mode E Bridge PPPoE Frames Between WAN and Local Ports Multicast Proxy C Enable IGMP Multicast Proxy Back Next 22 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng telecoMm 5 Click Next t
28. h the TR 069 Server TR 069 client Configuration WAN Management Protocol TR 069 allows a Auto Configuration Server ACS to perform auto configuration provision collection and diagnostics to this device Select the desired values and click Apply Save to configure the TR 069 client options Inform Disable Enable Safe Link Cert Import Inform Interval ACS URL ACS User Name ACS Password WAN Interface used by TR 069 Any WAN client d Display SOAP messages on serial Di console Disable O Enable vV Connection Request Authentication Connection Request User Name admin Connection Request Password eesee Connection Request URL null 52 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 Sac telecoMem DataRoute voice User Manual 13 9 Ping Reboot The Ping Reboot feature can be used to monitor the status of the internet connection and to automatically restart the DataRoute voice when the internet connection is unavailable Go to path Tools gt Ping Reboot Ping Reboot Settings Disable Ping Reboot Enable Ping Reboot Ping IP Address 4 2 2 2 Ping Interval range 10min 3600min Enter an IP Address to ping in order to test the internet connection and a ping interval for how often to check the connection 13 10 3G Link Notice The 3G Link Notice feature can be used to send an SMS to inform the user when the 3G data connection is unav
29. he second IP Address and Subnet Mask for LAN interface Apply Save Set the required options then click the Apply Save button Important Note changes will take effect immediately and if the IP Address of the DataRoute voice is changed the connection to the web interface will be lost The new IP address will need to be entered into the web browser The PC must be in the same subnet as the new IP address to view the webpage IP Address enter the IP address that the DataRoute voice will be available on The default IP address is 192 168 1 1 Subnet Mask enter the Subnet Mask The default subnet mask is 255 255 255 0 Enable IGMP Snooping select to have the DataRoute voice monitor all IGMP network traffic for the purpose of reducing the multicast overhead Advanced option 37 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew Disable DHCP Server turn off the built in DHCP server If the DHCP server is disabled all clients will need to have manually assigned IP addresses in order to connect Enable DHCP Server turn on the built in DHCP server Start End IP Address enter the range of IP addresses that the DHCP server can assign to clients These IP addresses must be in the same subnet as the IP address assigned to the DataRoute voice Leased Time enter the duration for the lease of DHCP IP addresses default is 24 hours Static DNS Server enter an IP
30. ice to the specified server NOTE The Internal Port End cannot be modified directly Normally it is set to the same value as External Port End However if you modify Internal Port Start then Internal Port End will be set to the same value as Internal Port Start Remaining number of entries that can be configured 32 Use Interface 1_VOIP_INTERNET R_orangeinternet ppptd3g0 e Service Name Select a Service Select One w CH Custom Service Server IP Address 1927 168 1 Apply Save External Port Start External Port End Protocol Internal Port Start Internal Port End el Le d e Hl Le Do d O AE Bel LL l e Use Interface select the WAN interface to forward from e Service Name either select from the list of predefined services e g Web Server HTTP or enter a name for a custom service e Server IP Address enter the local IP Address to forward network traffic to e Ports Table if a predefined service is selected the table will be completed automatically If a custom service is being entered the table must be filled in manually o Enter the range of IP addresses to match from the external WAN interface start and end ports can be the same to match a single IP Address o Select the Protocol TCP UDP or both TCP UDP o Enter the range of IP addresses to forward to at the internal host These can be the same as the external ports or the traffic can be forwarded to a different port on the interna
31. ider 44 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wp DataRoute voice User Manual LCLECOM Ew Voip Dialplan Setting specify the dial strings to be matched for VoIP calls All numbers dialled which match one of the dial strings will be dialled via the SIP Service Provider all numbers dialled which do not match any of the dial strings will be dialled via the GSM 3G network Key xX any digit 1 or more digits T dial after timeout dial immediately when terminator dialled separator between dial strings e g 9x T 9x all numbers starting with a 9 will be dialled via SIP numbers will be dialled after a timeout or after a is dialled 012x T 013x T all numbers starting with 012 or 013 will be dialled via SIP numbers will be dialled after a timeout Use SIP Proxy enable to allow using SIP Proxy Enter the SIP proxy address IP address or FQDN and port Use SIP Outbound Proxy enable to allow using SIP Outbound Proxy Enter the SIP Outbound Proxy address IP address or FQDN and port Use SIP Registrar enable to register to a SIP server Enter the SIP Registrar address IP address or FQDN and port SIP Account Account Enabled Physical Endpt Id Authentication Name 1001 Password 1001 Preferred Ptime 20 sl Preferred Codec 1 G 11ALaw k Preferred Codec 2 Preferred Codec 3 167231 M Preferred Codec 4 Preferred Codec 5 G 26_32 v Preferred Codec 6 GSM
32. l host Enter the required values and then click the Apply Save button 26 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 7 7 Advanced IP Routing Static Route Go to page Network gt Static Route Routing Static Route A maximum 32 entries can be configured IP Version DstIP PrefixLength Gateway Interface metric Remove This page allows the user to manually edit the routing table and create Static IP Routes Note that in normal operation this is not required Click the Add button to add a new static route Routing Static Route Add Enter the destination network address subnet mask gateway AND OR available WAN interface then click Apply Save to add the entry to the routing table Destination IP address prefix length optional metric number should be greater than or equal to zero Apply Save e Destination IP address prefix length enter the destination in the format IP address network prefix e g 124 80 0 0 16 e Interface select the network interface to route to e Gateway IP address specify the IP address for the gateway if required e Metric optional specify the route metric Metric Enter the required values and then click the Apply Save button 27 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 7 8 QoS Configuration P
33. lease go to path Network gt QoS Configuration page to enable Queue Management Configuration If Enable QoS checkbox is selected a default DSCP mark should be chosen to automatically mark incoming traffic without reference to a particular classifier Click Apply Save button to save Note If Enable QoS checkbox is not selected all QoS will be disabled for all interfaces The default DSCP mark is used to mark all egress packets that do not match any classification rules QoS Queue Management Configuration If Enable QoS checkbox is selected choose a default DSCP mark to automatically mark incoming traffic without reference to a particular classifier Click Apply Save button to save it Note If Enable Qos checkbox is not selected all QoS will be disabled for all interfaces Note The default DSCP mark is used to mark all egress packets that do not match any classification rules v Enable QoS QoS QUEUE QoS Class Select Default DSCP Mark No Change 1 Apply Save Please click QoS QUEUE button to enter the QoS Queue setup page then click Add button This screen allows you to configure a QoS queue and assign it to a specific layer 2 interface The scheduler algorithm is defined by the layer 2 interface Click Apply Save to save and activate the queue QoS Queue Configuration This screen allows you to configure a QoS queue and assign it to a specific layer2 interface The scheduler algorithm is defined
34. nnections are available the DataRoute voice can failover to the 3G connection when the ADSL connection is unavailable To use the feature check the Enable Automatic 3G backup box and enter the amount of time in seconds that the ADSL link must be unavailable before switching to 3G Then click Apply Save WAN Device Settings Please click Apply Save to save you configure Enable Automatic 3G backup Time out all dsl linkdown to run 3G seconds en seconds WAN Device Select ADSL Apply Save Then go to path Network gt WAN Service WAN Service Choose Add Edit or Remove to configure a WAN service over a selected interface If Ports Binding is enable only the binding port can access to the internet If Ports Binding is disable all of the ports can access to the internet Enable Ports Binding 3G Network WAN Service Setup ee Connect binding Dial a 5 Interface Description Hode t APN eg Igmp NAT Firewall Status Edit Action ppptd3g0 ppptd3g AlwaysOn none 3gnet null Disabled Enabled Enabled Connected amp Connect Disconnect a Click the Edit button for the 3G service 19 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew PPP Connect Mode Auto Connect w PPP author AUTO v APN mobile o2 co uk Auto reconnect interval time on O OS Service Mode VOIP_INTERNET wi Port Bind kel LAN 1 LAN2 LAN3 LAN4
35. o check the Summary of this connection WAN Setup Summary Make sure that the settings below match the settings provided by your ISP PORT VPI VCI 0 0 35 Connection Type PPPoE Service Name pppoe_0_0_35 Service Category UBR IP Address Automa ticaly Assigned Service State Enabled NAT Enabled Full Cone NAT Enabled Firewall Enabled IGMP Multicast Disabled Quality Of Service Disabled Click Apply Save to have this interface to be effective Click Back to make any modifications Back Apply Save 6 Click Apply Save to enable the connection 23 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 7 3 SIM PIN 3G Settings Go to path Network gt 3G Settings PIN Settings PIN code operation Disable When PIN lock disabled SIM card can be activated without PIN auth Enable When PIN lock disabled SIM card should be activated after PIN auth successfully Modify Set PIN code as a new one PIN code 4 8 decimal digits PUK code 8 decimal digits When SIM card is PIN locked it should be unlocked with correct PUK code Residual allowed try time After these times SIM card will be locked PIN State Disabled PIN code operation Residual allowed try time 3 Apply Save This page allows the user to enable or disable the SIM pin function Select whether the SIM Pin should be enabled or disable
36. o enable detection of CNG Fax tones Ingress Gain used to increase or decrease the volume of the incoming audio Egress Gain used to increase or decrease the volume of the outgoing audio 46 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM ew Enable T38 Support d Enable V18 Support Registration Expire Timeout D Registration Retry Interval A DSCP for SIP EF 101110 DSCP for RTP EF 101110 f Dtmf Relay Setting InBand e Hook Flash Relay Setting None e SIP Transport Protocol UDP Le J Enable SIP Tag Matching Uncheck for Vonage Interop SIP Prack Music Server Music Server Port 0 Enable T38 Support enable support for T 38 fax compatible devices Enable V18 Support enable support for V 18 Textphone compatible devices Registration Expire Timeout enter the timeout length for the registration Registration Retry Interval enter the retry interval for the registration DSCP for SIP RTP select the codepoint to use when connecting via QoS compatible systems Dtmf Relay Setting select the format to transmit DTMF tones to the network Tones can be transmitted In Band or Out Of Band SIP INFO or RFC2833 Hook Flash Relay Setting select whether local Hook Flash should be ignored or sent as SIP INFO packet SIP Transport Protocol select the protocol UDP or TCP to use for SIP packets Most s
37. o identify outgoing IP traffic by specifying a new filter name and at least one condition All of the specified conditions in this filter rule must be satisfied for the rule to take effect Click Apply Save to save and activate the filter Add IP Filter Outgoing The screen allows you to create a filter rule to identify outgoing IP traffic by specifying a new filter name and at least one condition below All of the specified conditions in this filter rule must be satisfied for the rule to take effect Click Apply Save to save and activate the filter Filter Name IP Version IPv4 X Protocol v Source IP address prefix length Source Port port or port port Destination IP address prefix length Destination Port port or port port Apply Save 40 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 11 3 Domain Filters Please go to path Firewall gt Domain Filters page Please select the list type first then configure the list entries List type Exclude accept all the DNS except the list Include drop all the DNS except the list domain Filter Please select the list type first then configure the list entries Maximum 100 entries can be configured Exclude default accept all the DNS expect the list Include default drop all the DNS expect the list domain List Type Exclude Include Address Port Remove Add
38. on for analogue telephones Connection for ADSL enabled telephone line Manually connect disconnect 3G data Start Wi Fi Protected Setup Restore to factory default settings Power LAN1 4 Internet ADSL Indicators Phone Wi Fi 3G d Power Right Side LAN1 4 Phone ADSL 3G Left Side WPS Reset 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Fw 3 2 Package Contents ADSL Splitter 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 4 Getting Started 4 1 Hardware Connection Power LAN 1 LAN 2 LAN 3 LAN 4 Phone ADSL ver a ea OS Analog Phone Modem LapTop Splitter LINE DSL Line Phone RJ11 Cable RJA Cable Analog Phone 1 Use a telephone cord to connect the LINE port of the splitter with the phone socket on the wall only if using ADSL 2 Use another telephone cord to connect the MODEM port of the splitter with the ADSL port of the DataRoute voice only if using ADSL 3 Connect Ethernet port of the DataRoute voice with 10 100BASE T port of the computer using the network cable that comes with the unit 4 Plug in the power cord and turn on the power 4
39. on the Status menu in the web interface The following status information is available by clicking the links on the left of the webpage Basic Info Includes hardware and software versions system time info and basic IP information Network Status Includes basic 3G status SIM card details network and signal strength and basic ADSL Status WAN Info Lists the configured WAN 3G and ADSL interfaces and shows type connection status and basic IP information WLAN Status Includes basic Wireless information and a list of clients connected wirelessly Connected Devices Shows a full list of connected clients both wired and wireless Routing Table Displays the current IP routing table Statistics Displays a list of configured WAN 3G and ADSL interfaces and shows the amount of traffic sent and received on each interface VoIP Status Shows the current registration status of a configured VoIP provider 11 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wp DataRoute voice User Manual LCLECOM Ew 6 Quick Setup Click on the Quick menu in the web interface This will show a quick setup wizard that allows the user to configure the most commonly used options Step 1 Access Account Old Password fs New Password Po Confirm Password sid This sets the username and password to access the web interface The default username to access the DataRoute voice is admin The default pa
40. or the rule to take effect Click Apply Save to save and activate the filter Add IP Filter Incoming The screen allows you to create a filter rule to identify incoming IP traffic by specifying a new filter name and at least one condition below All of the specified conditions in this filter rule must be satisfied for the rule to take effect Click Apply Save to save and activate the filter Filter Name IP Version IPv4 v Protocol X Source IP address prefix length Source Port port or port port Destination IP address prefix length Destination Port port or port port WAN Interfaces Configured in Routing mode and with firewall enabled and LAN Interfaces Select one or more WAN LAN interfaces displayed below to apply this rule JJ Select All v ppptd3g ppptd3g0 d br0 bro Apply Save By default all outgoing IP traffic from LAN is allowed but some IP traffic can be BLOCKED by setting up filters Please go to path Firewall gt IP Filters gt Outgoing IP Filtering Setup Outgoing IP Filtering Setup By default all outgoing IP traffic from LAN is allowed but some IP traffic can be BLOCKED by setting up filters Choose Add or Remove to configure outgoing IP filters Filter Name IP Version Protocol SrcIP PrefixLength SrcPort DstIP PrefixLength DstPort Remove Add Remove Click Add button to configure outgoing IP filters The following interface allows the user to create a filter rule t
41. reen for more details on available options refer to section 10 Step 5 3G Failover Enable Automatic 3G backup Time out all dsl linkdown to run 3G seconds en seconds WAN Device Select ADSL When both ADSL and 3G connections are available the DataRoute voice can failover to the 3G connection when the ADSL connection is unavailable To use the feature check the Enable Automatic 3G backup box and enter the amount of time in seconds that the ADSL link must be unavailable before switching to 3G Click Next 15 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew Step 6 Configure 3G and ADSL connections To setup the 3G connection 3G Network WAN Service Setup Connect binding APN DE al Interface Description Hada t a Igmp NAT Firewall Status Edit Action ppptd3g0 ppptd3g AlwaysOn none 3gnet null Disabled Enabled Enabled Connected amp Connect Disconnect Click the Edit button for the 3G service PPP Connect Mode Auto Connect wv PPP author AUTO v APN mobile o3 co uk Auto reconnect interval time on O O Service Mode VOIP_INTERNET w Port Bind kel LANI LAN2 LAN3 F LAN4 SSID1 Enable LAN DHCP Apply Save For most networks it is only required to set the correct APN value this should be provided by your network operator leave the other settings on default values If your network
42. requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection Rea User name Password Remember my credentials The default user name and password is admin for web log on Press ENTER or click on OK to enter the configuration interface Warning Please be sure the IP of the computer network card is in the same IP range as the DataRoute voice LAN port before trying to log on ex 192 168 1 2 and 192 168 1 1 are in the same IP range If the login is not displayed please check in Internet Explorer Tools Internet Options Connection LAN Setup Proxy server disable the function Proxy for LAN and then retry If log on successful the status page will be displayed as follows Status a Siats Cod Ee E Basic Info P Basic Info Device Model DataRoute voice P Network Status Hardware Version V1 5 b WAN Info Software Version 1 1 2 System Run Time 48 seconds M WLAN Status Current Time Thu Jan 1 00 00 47 1970 2 MAC Address 00 1a a9 b3 04 65 P Connected Devices LAN Subnet IP 192 168 1 1 P Routing Table LAN Subnet Mask 255 255 255 0 Default Gateway Statistics Primary DNS Server Secondary DNS Server P VoIP Status Svnchronizved Time 10 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 5 Status Click
43. requires login enter the valid PPP Username and PPP Password Fill in the required information and click the Apply Save button 16 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng telecoMm To setup the ADSL connection ADSL Network WAN Service Setup Interface Vpi Vci Category Qos Description am 0 35 UER Disabled 2_INTERNET_B_0_35 atmi_i E 35 UBR Disabled 3_INTERNET_B_8_35 NS Click the Add button to start the ADSL network wizard VPI 0 255 lo VCI 32 65535 Enter the values for VPI and VCI supplied by the ADSL Service Provider and click Next Select DSL Link Type EoA is for PPPoE IPoE and Bridge EoA PPPoA IPoA Encapsulation Mode VC MUSX w Service Category UBR Without PCR Select the DSL link type and Encapsulation Mode supplied by the ADSL service provider note please choose EoA for PPPoE connection and click Next Select WAN service type PPP over Ethernet PPPoE IP over Ethernet Bridging Enter Service Description pppoe_0_0_ 38 Service Mode INTERNET wi Port Bind LANI LAN LAN3 Lada SSID1 Enable LAN DHCP 37 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng LIECOM Fw If EoA link type was selected choose the WAN service type normally PPP over Ethernet PPPoE Click Next PPP Username fs P
44. s is the name that will be displayed when users search for Wi Fi networks e Country select the country where the DataRoute voice is installed e Max client number specify the maximum number of Wireless clients that will be allowed The DataRoute voice supports up to 16 simultaneous Wi Fi connections e Channel select the Wireless channel to use The channel number can be changed if interference is experienced After entering the required settings click the Apply Save button 33 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew 9 2 WLAN Security Go to path WLAN gt WLAN Security The default Wireless Pre Shared Key is data1234 it is strongly recommended that this be changed It is recommended that all other security settings be left unchanged to maintain maximum security and compatibility You can set the network authentication method selecting data encryption specify whether a network key is required to authenticate to this wireless network and specify the encryption strength Click Apply Save when done Enable WLAN security Network Authentication Mixed WPAZANPA Dh se WPA Pre Shared Key Click here to display WPA Group Rekey Interval WPA Encryption TKIP AES WEP Encryption Apply Save Enter a new WPA Pre Shared Key and then click Apply Save This is the key that must be entered whenever connecting a PC or
45. ssword is admin To change the password 1 Select admin from the Username drop down box Enter the password admin in the Old Password box Enter a new password in both the New Password and Confirm Password boxes Click the Next button Login with the new password Click on the Quick menu to continue the wizard gt is To continue to the next step without changing the password click the Skip button 12 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew Step 2 Time Settings Current Time Thu Jan 1 00 24 29 1970 Set Time Mode Time Server Manual Setting jo hour24 minute Time Zone Offset GMT Greenwich Mean Time Dublin Edinburgh Lisbon London ze Time From this page the current time can be set manually or the DataRoute voice can be set to obtain the correct time from an internet time server Note it is recommended that an internet time server is used when available if the time is set manually it will be lost in the event of a power cut or if the unit is restarted To set the time manually 1 Select Manual Setting 2 Enter the current time 3 Select the correct Time Zone 4 Click Next To use an internet time server 1 Select Time Server 2 Enter the time server domain name e g time nist gov or pool ntp org 3 Select the correct Time Zone 4 Click Next 13 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax
46. telecomen DataRoute voice telecoMrm DataRoute voice Installation and User Manual Version 4 October 2011 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Manual LCLECOM Ew Document Control Dec 2010 1 release of document Dec 2010 Added VoIP options Jan 2011 Security Options Oct 2011 Additional features and options Notices Emergency Calls This terminal operates using mobile signals which cannot guarantee connection in all conditions Therefore you should never rely solely on the terminal equipment for essential communications such as medical or emergency services No responsibility is assumed by TFM for the use or reliability of the DataRoute voice when used in a situation or with other equipment not supplied or specified by TFM TelecomFM shall accept no liability for any error or damages of any kind resulting from the use of this document or the equipment it relates to The wording in this document may change from time to time Please refer to the TelecomFM web site www telecomfm co uk for the latest release XK 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 e DataRoute voice User Hen L lGGOTfc 1 Contents e ES 3 2 OOS Wy aaa sentir ac a a a 5 3 SOS e ld Lei d Le sa fara orafara asa neat neta EE 5 Sai ai elle lee Gite aC eS EE 5 Baz Pakage EE EE 7 4 Getting Started E 8 4 1 Hard
47. ttings in the DataRoute voice have not been modified Note 2 To start a Command Prompt in Windows click on the Start menu Programs Accessories Command Prompt Note 3 The returned values of ping command in the following format show the standard of reachable CoNsers Pretender ping 192 168 1 1 Pinging 192 168 1 1 with 32 bytes of data Reply from 192 168 1 1 bhytes 32 time ims TTL 64 Reply from 192 168 1 1 bytes 32 timetims TTL 64 Reply from 192 168 1 1 bytes 32 timetims TTL 64 Reply from 192 168 1 1 bytes 32 timetims TTL 64 Ping statistics for 192 168 1 1 Packets Sent 4 Received 4 Lost B Cx loss Approximate round trip times in milli seconds Minimum ms Maximum ims Average Bms 6 If ping of the modem is reachable but ping of the internet fixed IP is unreachable attention should be concentrated upon device settings Please enter the web interface following the instructions in this manual 1 Check first the number of WAN connections If more than one connection exists for troubleshooting delete unused connections and leave the one connection you are using 2 Check the connection to see whether correct type is selected When you use PPPoE PPPOA to login the following information should be provided VPI and VCI which can be queried from your ISP user name and password 3 Then make sure that using NAT and default gateway have been selected with a tick Check whether Dial on d
48. ware Connection s ssssssssssersrsnrnrsnsrrnrnrnrerenrnrsnerrnrnrnrrrerrnrnrrrrrrnrnrrrerne 8 42 Computer EECH 9 SES WOO UN E 10 5 EES 11 6 QUICK EE Mee 12 7 INGUWOUM EEN 19 7 1 3G Configuration WAN Device WAN Gervicel cece eeeeeeeeeeeeeeeeeeeeeneeenas 19 KC PDSLComiGguraon WAN Service EN 21 FS SU PUN CG Se de LC E 24 7 4 Advanced ADSL SettingdS ENNEN ENNEN REENEN 25 Fc DMZ TAOS EE 25 7 6 Port Forwarding Virtual Servers ENNEN ENNER ENNER ENN 26 7 7 Advanced IP Routing Static Route 27 Fis OOS e et delt AL OW ee xaeeueaseeesneecaneseeesneecnweceeesneecaweceercucucucaceessuencuvaceessueaquaaees 28 8 Velo Cer La Le EE 30 OE UPIP CUNG EE 30 Sie DYME Ki KE 30 S VEN NEE VPN E 31 8 4 ENEE ee 32 9 Wireless CVA RE 33 PL WEAN BISE aa a 33 Pe WAN SS Di gie EE 34 Tao Aan d SUG e E E E E EEN E EEE E E E E E EEE 34 3 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 DataRoute voice User Manual telecom FM 9 4 WELAN MACG icusnorecceseeeeereeserysseeeeesesseseuresseseereeseeseeyeseereeyeseeseeeesseayeree 35 Da WAN EE 36 EO LAN DHCP ecca 37 ti PIPC WOW oce 39 LLL FEW gg e EE 20 Be CA E 39 Dies DONN FIUO O rinn 41 ILA MAC FIC eee sree pee carers eeceeeen een cavencen cancer ceqeneecceueesecceceeseceeeeercequqqen 42 11 5 Access Control Remote ACCESS c cccsseceeecsccnsnereeessccusaeteessseusnareeenseaueannes 43 12 VOICE VOIP E 44 IAL VOICES CONMOULAUIOWM W 44 E222 et E e S
49. www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 5 telecoMem DataRoute voice User Manual 13 2 Time Settings Go to path Tools gt Time Settings From this page the current time can be set manually or the DataRoute voice can be set to obtain the correct time from an internet time server Note it is recommended that an internet time server is used when available if the time is set manually it will be lost in the event of a power cut or if the unit is restarted Current Time Thu Jan 1 10 46 42 1970 Set Time Mode Time Server Manual Setting Time Zone Offset SMT Greenwich Mean Time Dublin Edinburgh Lisbon London Apply Save Enter the required options and click the Apply Save button 49 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wy DataRoute voice User Heng LIECOM Fw 13 3 Backup Settings To backup the current configuration to a file Please go to path Tools gt Backup Settings page Click Backup Settings button then a File download window will pop up Click Save button to download save current configuration of the device to the PC Settings Backup Backup Broadband Router configurations You may save your router configurations to a file on your PC File Download LZ Do you want to open or save this file CG Name backupsettings conf Type Application From 192 168 1 1 Open Save Caes While files
50. ystems use UDP Enable SIP Tag Matching uncheck when using with Vonage SIP Prack use the SIP Prack method instead of ACK Music Server enter an address and port for an external music server to provide music on hold 47 4Gon www 4Gon co uk info 4gon co uk Tel 44 0 1245 808295 Fax 44 0 1245 808299 wW DataRoute voice User Heng TElECOMm 13 Tools 13 1 Account Settings Users When you configure the DataRoute voice through an Internet browser the system requires user name and password to validate access permission The factory sets the default username of admin and the password of admin Go to path Tools gt Account Settings you can choose the username and change the password Access Account Access to your DSL router is controlled through three user accounts admin support and user The user name admin has unrestricted access to change and view configuration of your DSL Router The user name user can access the DSL Router view configuration settings and statistics as well as update the router s software Use the fields below to enter up to 16 characters and click Apply Save to change or create passwords Note Password cannot contain a space Username M new name Old Password New Password Confirm Password _ Apply Save Attention please remember the password after change otherwise you will need to reset the device and will lose all configuration settings 48 4Gon

Telecom FM Dataroute Voice Manual

Contents

Download Pdf Manuals

Related Search

Related Contents