User`s Manual
Contents
1. Scan Test 1 With the scanner running LED red and the host system on scan few known good barcodes 2 Check result on host screen If scanner is reading correctly no further set up is necessary If scanner reads incorrectly then go to Set Up next Set Up 1 With the scanner running LED red and the host system on scan lt Enter Exit Programming Mode gt barcode found on the inside cover of the Programming Guide 2 Scanner is ready for programming if it gives one low beep sound followed immediately by a high beep sound and LED turns green 3 Find the barcode which corresponds to the parameter you require in the Programming Guide 4 Scan the desired barcodes one by one as the scanner beeps once for every barcode it memorizes 5 When all finished scan lt Enter Exit Programming Mode gt barcode again The scanner will beep twice one long and one short When LED turns red the scanner has been programmed 6 Test scan few known good barcodes to make sure the scanner reads correctly If not try set up procedures again 3 Operation and Indicators 3 1 Operation This scanner is omni directional reading barcodes in sweep and presentation mode depending on the host system it is attached to Sweep mode means moving items through the scan window left to right right to left top to bottom bottom to top etc are all okay Presentation mode is when an object is moved toward the scan window presented until the barcod2. RSS Expanded RSS Limited Programmable tone and beep time Keyboard RS 232C USB1 1 Wand 120 5mm 71 35mm 108 3mm 250g Standard 2m straight 5VDC 10 1 0Watts 200mMA 5 0V CDRH Class Ila IEC 60825 1 Class 1 CE amp FCC DOC compliance 0oC 400C 200C 600C 5 95 RH non condensing max 2500LUX fluorescent Designed to withstand 1m drops Dimensions Scan field 5 milQ0 127 mO 55 10 6 mildO 15mm O 45 115 7 5 Mid0 13mm Q 40 14 10000 25 mm Q Le 20 18 ild0 33mm 000 WPGEANO
3. User s Manual OMNI 652 series Omni Directional Laser Scanner Specifications subject to change without notice Radio Notice This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with the instructions in this manual it may cause interference to radio communications The equipment has been tested and found to comply with the limits for a Class A computing device pursuant to EN55022 an 47 CFR Part 2 and Part 15 of the FCC Rules These specifications are designed to provide reasonable protection against interference when operated in a commercial environment Radio and Television Interference Operation of this equipment in a residential area can cause interference to radio or television reception This can be determined by turning the equipment off and on The user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the device with respect to the receiver Move the device away from the receiver Plug the device into a different outlet so that the device and the receiver are on different branch circuits If necessary the user may consult the manufacturer an authorized dealer or experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Pr
4. canner will be positioned horizontally to the host machine without cable interference for optimal mounting See pictures below Connecting to the Host The scanner connects to a host terminal by an interface cable This cable connects to the scanner with a modular connector and connects to the host terminal with the connector required by the host RS 232 keyboard wedge or USB Different connectors used depending on the host Please make sure the right cable is used for connecting the scanner to your host terminal 2 3 Connecting to the host The scanner connects to a host terminal by an interface cable This cable connects to the scanner with a modular connector and connects to the host terminal with the connector required by the host RS 232 keyboard wedge or USB Different connectors used depending on the host Please make sure the right cable is used for connecting the scanner to your host terminal Setting Up the Scanner No set up is required if the scanner is either pre programmed or it auto detects and is ready to be used Otherwise the scanner must be informed about the type of system it is connected to This can be done quickly using the Programming Guide that s included in the package The Programming Guide is used to set parameters such as communication interface type RS 232 Keyboard USB beep tone beep volume sleep mode timing and same code delay time Set up of a parameter does not interfere with another parameter
5. e buzzer makes four short beep sounds When the self test is finished the LED light will turn red 5 Place the test barcode in front of the scanner If the scanner works right it will make a short beep sound and the LED will show green light indicating a good read then the test barcode can be removed NOTE 1 If the scanner does not make any beep sounds or makes the wrong beep sound or no LED light shows when power is connected remove power from scanner and refer to troubleshooting section 2 If the scanner is using RS 232 or keyboard wedge interface cables it is able to scan barcodes continuously when power is on If the scanner is using USB interface cable it will only be able to scan barcodes continuously only when connected to a host If the scanner is not connected to a host it will be able to read one barcode only LED light stays green Mounting 1 Scan performance will not be affected by the mounting direction of the scanner 2 Use mounting holes on the bottom or and back of the scanner to mount the scanner onto host machine templates at the last two pages of the manual can be used Back View Bottom View LE SV LRTI eee HH 33 00 GAPAS USERELE SCREW INSERTION 1S Ale M A A G 2 0 F EF y 1 Te R Unit mm inch SR strain release that is connected to the cable rotates 90 to comply with the way the scanner is mounted Therefore the s
6. e is read then the object is removed 3 2 Indicators LED Indicators LED Status Indications C no power applied to the scanner steady red light the scanner is on and ready to scan one blink of one barcode has been steady green scanner is in programming light mode a barcode has been successfully decoded but the object has not been removed from the scan window steady orange this indicates motor failure for light motor failure a periodic beeping sound will also be heard flashing orange scanner has a laser subsystem light failure return to repair Beeps Beeps Status Indications one beep a barcode has been K ee series of 4 scanner passed self test beeps and is operating properly when scanner is powered up series of 2 when scanner is entering programming mode continual failure indication return to beep repair 4 Specifications 4 1 Controlling the Scanner from a Host System The scanner can be controlled from the host system via the RS 232C interface Control can be accomplished by transmitting the following single byte commands to the scanner The default setting for the commands are as follows ASCII Byte is Also Function Code Called OE Hex enable resumes disable Shift Out or lt Ctrl N gt Shift In or OF Hex disable lt Ctrl O gt 05 Hex power up ENQ or lt Ctrl E gt re initialization sleep DC2 lt Ctrl R gt wake up resumes sleep Poet Note When the scanner i
7. o not remove the protective housing of the scanner There are no user serviceable parts inside Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure Optical The use of optical instruments with this product will increase the eye hazard Optical instruments include binoculars magnifying glasses and microscopes but do not include normal eye glasses worn by the user Table of Contents 1 General Information 2 Quick Start 2 1 Unpacking amp Parts Identification 2 2 Power and Verifying Scanner Operation 2 3 Connecting to the host 3 Operation and Indicators 3 1 Operation 3 2 Indicators 4 Specifications 4 1 Controlling the Scanner from a Host System 4 2 Specifications 1 General Information Main Features The Omni directional Laser Scan Module is an easy to intergrate unit that performs 5 directions of scan field with a 20line scan pattern cycling at 1200 scan per second for quick accurate reads The scanner s smart small cubic design allows for easy integration into new equipment and efficiently reduces overall equipment size Multiple interfaces include keyboard wedge USB1 1 RS 232 2 Quick Start 2 1 Unpacking amp Parts Identification Unpacking Omni 652 Unit x 1 User s Manual x 1 On CD Programming Guide x 1 5V Adaptor optional x 1 Parts Identification Scan Window LED Indicator Buzzer O
8. oblems This booklet is available from the U S Government Printing Office Washington DC20402 U S A Stock No 004000003454 For CE countries This scanner is in conformity with CE standards Please note that an approved CE marked power supply unit should be used in order to maintain CE conformance Laser Safety The Omnidirectional Laser Scan Module complies with safety standard IEC 60825 for a Class I laser product It also complies with CDRH as applicable to a Class Ila laser product Avoid long term staring into direct laser light Radiant Energy The Omnidirectional Laser Scan Module uses one low power visible laser diode operating at 650nm in an optomechanical scanner resulting in less than 3 9uW radiated power as observed through a 7mm aperture and averaged over 10 seconds Do not attempt to remove the protective housing of the scanner as unscanned laser light with a peak output up to 0 8mW would be accessible inside Laser Light Viewing The scan window is the only aperture through which laser light may be observed from this product A failure of the scanner motor while the laser diode continues to emit a laser beam may cause emission levels to exceed those for safe operation The scanner has safeguards to prevent this occurrence If however a stationary laser beam is emitted the failing scanner should be disconnected from its power source immediately Adjustments Do not attempt any adjustments or alteration of this product D
9. ptical Wake up Sensor 2 2 Power and Verifying Scanner Operation Power The scanner needs a minimum of 200mA at 5V power The power link interface cable that comes with the scanner supports both direct power where the scanner takes power from the host machine and external power the power adapter that s plugged into an AC outlet If the host machine supplies power it must be the same as the input power specified 200mA 5V When external power is used the scanner does not take power from the host machine There is no on off switch on the scanner It turns on when power is connected and turns off when power is removed It is advised to turn off your POS or host system before installing the scanner to avoid electronic damage to your computer Make sure to use only AC DC power adaptor approved for the scanner The usage of other power supplies may cause damage to the product that s not covered by factory warranty Verifying Scanner Operation Before installing the scanner follow the procedures below to make sure scanning go on properly 1 Connect the scanner with host through cable that is attached to the scanner 2 If adaptor is not required go directly to step 4 Insert the 8 pin modular plug of the power link cable into the host connector in the back of the scanner until a firm click is heard 3 Plug the power adaptor into the jack on the power link cable 4 When the scanner powers up LED light up in green and th
10. s disabled the motor of the scanner will stay on until the scanner goes into sleep mode Maintaining the Scanner The scanner rarely needs any maintenance only an occasional cleaning of the scanner window is necessary to remove any dirt or fingerprint To clean the scanner window use a soft lint free cloth and non abrasive cleaner to avoid scratching the scanner window The scanner window can be cleaned while the scanner is running 4 2 Specifications Specifications Operational Light source 650nm visible laser diode Depth of Scan 0 210mm UPC EAN 100 PCS Field 90 Number of Scan 20 Lines Scan Pattern 5 directions of scan field Scan Speed 1200 scan per second Minimum Bar 5mil PCS 90 Width Print Contrast Indicators LED Decode Capabilities Beeper Operational System Interfaces Physical Height Depth Width Weight Cable Power Input Voltage Power Operating Current Laser Class EMC Environment Operating Temperature Storage Temperature Humidity Light Level Shock 30 UPC EAN100 two color LED red and green UPC EAN JAN UPC Versions A amp E EAN 8 EAN 13 JAN 8 JAN 13 Addendum 2 or 5 ISBN ISSN Japa nese Bookland Code 39 with full ASCII Codabar NW7 Code 128 EAN 128 Code93 Interleaved 2 of 5 MSI Plessey China Post Code Code 32 Italian Pharmacoe Optional Industrial 2 of 5 Standard 2 of 5 Discrete 2 of 5 Matrix 2 of 5 IATA Code Code 11 RSS 14
Download Pdf Manuals
Related Search