User manual - Tripmeters for rallies.
Contents
1. SPARKELECTRONICS Pobert Skierski Biuro 01 424 Warszawa Al Prymasa Tysiaclecia 78a tel fax 022 836 24 51 www rajdowe haldy pl SPARKELECTRONICS Technical and operational data e power supply 7 30V e dimensions W57xS160xG32 mm e current max 200 mA SPARKELECTRONICS Robert Skierski Biuro 01 424 Warszawa Al Prymasa Tysiaclecia 78a tel fax 022 836 24 51 www rajdowe haldy pl SPARKELECTRONICS Warranty The warranty covers the period of 12 months from the date of sale of the device The cover is valid only if the device has been used respectively to its intended purpose and with the proof of purchase Name and type cecceccseeeeeeeeeeeeeeeeeseeeseaeeeeaeeeeeees Date of sale Device NUMD GI cssiscevvacesstsescvsierderrescaccavsies eves SPARKELECTRONICS Robert Skierski Biuro 01 424 Warszawa Al Prymasa Tysiaclecia 78a tel fax 022 836 24 51 www rajdowe haldy pl2. 51 www rajdowe haldy pl SPARKELECTRONICS Description of the function Tryb DISTANCE Press BRIEFLY the red button on the reset switch or F on the tripmeter to bring back the TRIP indication or cancel it if it had been displayed Press again to cancel the TRIP road Direct Action Press and hold 3 sec the red button to display the function selection menu The functions can be changed by short pressing of the Red button The functions can be changed only when the display is flashing After 3 sec the flashing stops The menu is presented in the following order TRACK course shows the course when GPS is connected n the left display you can see the degree symbol BAT voltage of the vehicle the voltage of the tripmeter s power supply shown in the upper display The symbol U indicates the voltage function TIME Time synchronization with the GPS transmitter is shown on the 5 digit display with 10 seconds resolution LED The LED function adjusts the display brightness This can be changed using the blue and black or UP DOWN buttons SPEED Current speed displayed on the right screen The left display shows S Through the menu UP or blue button and DOWN or black button ODO When the displays are presented other parameters pressing the buttons causes showing ODO Each pressing adjusts ODO value by 10 m For fast forwarding press and hold the button Direct Action
3. value press UP and then confirm by pressing DOWN The change will be confirmed by a quick screen flash To exit press F Available functions 1 Units the display shows UNIT select this function to choose between km or mile a metr metric system b imp imperial or British system 2 Pulses the display shows IMPS select this mode to choose between measurements using road pulses and GPS or using GPS only a __ off operation mode using only the GPS system measurement starts when speed is over 5 km h b l on operation mode using road pulses from the vehicle or from an additional sensor and the GPS system this measurement ensures greater accuracy 3 Daylight Saving Time the display shows DST Enabling and disabling Daylight Saving Time a on Enabled b off disabled 4 Time Zone the display shows UTC selecting the time zone in which the device is working There is choice of 24 zones from 12 to 12 To change the zone press F confirm choice press DOWN After programming all values when being in the main menu display shows UNIT or IMPS or DST or UTC press UP to exit indicates The tripmeter reset and settings save is confirmed by long beep Video covering this section http www rallycomputer com support video instruction video instruction rally computer 2 html SPARKELECTRONICS Robert Skierski Biuro 01 424 Warszawa Al Prymasa Tysiaclecia 78a tel fax 022 836 24 51 www rajdowe haldy
4. SPARKELECTRONICS Rally computer 2 Rally computer 2 GPS User manual Installation and configuration instructions with links to video instructions online at www rallycomputer com amp contents with S S only for version 2 GPS SPARKELECTRONICS Robert Skierski Biuro 01 424 Warszawa Al Prymasa Tysi clecia 78a tel fax 022 836 24 51 www rajdowe haldy pl SPARKELECTRONICS Tripmeter description The Rally Computer 2 tripmeter is a professional device used in rallies It has been specifically designed for motorcycles and quads It can be quickly and easily operated from the keyboard or the handlebar reset switch that comes in the kit Water tight aluminium casing provides exceptional protection against external factors Top class electronics ensures its reliability and high precision measurements The results are presented on super bright red LED displays The tripmeter is operated by a 3 button keypad and by a 3 button handlebar reset switch where each key has been assigned a measuring function Features Precise distance measurement using two independent counters TRIP and ODO with a 10m accuracy e direct ODO correction Backward counting when the vehicle moves backwards The switch is done automaticaly after changing to reverse gear Note The grey cable needs to be connected to the sensor or the reverse light bulb Current speed measured with 1 km h accuracy Vehicle s voltage indication Adju
5. pl SPARKELECTRONICS Configuration of distance measurements Calibration value The Cal value is the number of pulses generated by the vehicle over a distance of 1000m The measurement can be performed on any distance as long as the value entered is for the distance of 1000 m How to measure the Cal Value The tripmeter can measure the number of pulses for any distance Video covering this section http Avww rallycomputer com support video instruction video instruction rally computer 2 html How to input the Cal Value The tripmeter can store up to 10 values Video covering this section http www rallycomputer com support video instruction video instruction rally computer 2 html How to select a Cal Value To activate the Cal Value first select it from memory Selected value will be used for all calculations until the user decides to choose another value Video covering this section http www rallycomputer com support video instruction video instruction rally computer 2 html Operational modes Mode selection We have 1 option to select from o DISTANCE liaison navigation or off road mode From the Start Screen press UP the screen will show DIST Confirm by pressing OK Video covering this section http www rallycomputer com support video instruction video instruction rally computer 2 html SPARKELECTRONICS Robert Skierski Biuro 01 424 Warszawa Al Prymasa Tysiaclecia 78a tel fax 022 836 24
6. pmeter still consumes electricity reduced to a minimum When the tripmeter is not used for a long period it is recommended to disconnect it from the car installation This will prevent the battery from discharging It is best to install an external switch that fully disconnects the tripmeter from its power supply Do not install the tripmeter in places where it may be damaged or work improperly e g on airbaigs or air outlets Basic information Switching ON OFF After switching the power on the tripmeter o will display the start screen only when if it was earlier switched off while not making measurements or when it is switched on for the first time o will continue previous measurments only if it was earlier switched off while making measurements Switching off the tripmeter does not disconnect it completely from the power supply SPARKELECTRONICS Pobert Skierski Biuro 01 424 Warszawa Al Prymasa Tysiaclecia 78a tel fax 022 836 24 51 www rajdowe haldy pl SPARKELECTRONICS Basic configuration To enter the configuration menu you need to o restart the device from the keypad turn off the power supply when the tripmeter was in the start screen position and turn on the power again After the reset the display will show the 88888 and then the current CAL value At this point press 3 x UP and 1 x DOWN Then CONF will show on the display To select a function press UP and confirm with DOWN To change the
7. stable display brightness and backlit keys Measurements of non volatile memory with unlimited time Memory with up to 10 wheel calibration settings corresponding to different tyre sizes Connection to an external switch The possibility of calibration value change without deleting measurements amp nas Course displayed in the form of azimuth amp S S Clock synchronized with the GPS transmitter Installation instructions The tripmeter should be installed in a visible place allowing easy and quick access to the front panel The tripmeter has been supplied with mounting brackets for easier attachment Do not remove the brackets completely as this can unseal the tripmeter housing When connecting the power supply make sure that the voltage source is reliable and stable with the voltage within the range between 8 to 30 V SPARKELECTRONICS Robert Skierski Biuro 01 424 Warszawa Al Prymasa Tysiaclecia 78a tel fax 022 836 24 51 www rajdowe haldy pl SPARKELECTRONICS Superseal 6PIN connector sed i pame yellow a ignition switch white Taversing bulb __ speed sensor awch T n grey y f reversing 25 bult ozal blue any reset switch Superseal 2 PIN connector 3 button switch brown handlebar or manual any reset switch gt gt gt og GND NOTE Switching off the tripmeter does not disconnect it completely from the power supply The tri
Download Pdf Manuals
Related Search