(RS)-BZ1B Install Guide English
Contents
1. Parking Light will ash once 1x Time restriction Complete next step within 5 seconds from previous step Press once 1x on LOCK button of aftermarket remote Parking Light will ash once 1x To program additional remotes repeat steps 4 to 6 using each additional remote Wait Parking Light will ash twice 2x Turn ignition to OFF position START vehicle for 15 seconds Aftermarket Remote Programming Procedure completed www idatastart com Automotive Data Solutions Inc 2014 Page 17 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 gt gt gt gt gt gt 01 ENGINE START STOP OFF ACC ON START OFF 02 03 X 04 05 Y 06 07 Z 08 Z 09 10 11 Y 12 13 14 gt gt MODULE NAVIGATION PROCEDURE 1 OF 1 It is mandatory to exit the Module Navigation at the end of this procedure Failure to exit the Module Navigation will drain vehicle battery To exit the Module Navigation at any time Follow STEP 13 Module must be programmed to the vehicle Use the Module Navigation Chart on the next page Set ignition to OFF position TO ACCESS THE MENUS Press and hold programming button until LED 1 turns solid GREEN IN THE MENUS Press the programming button as many times as the menu number indicates LED 1 will ash GREEN an equal amount of times continuously TO ACCESS THE OPTIONS2. ash X number times to indicate an error code See table 03 N A 04 Trunk is open 05 Foot brake is ON 06 Hood is open 07 N A 08 Tach failure 09 N A 10 System is in Valet Mode 11 CAN communication failure 12 RS not synchronized Start vehicle with OEM key for 15 sec before trying a new RS sequence Remote staRteR shutDown eRRoR coDes notes Y numbeR oF PaRKing Light FLashes Diagnostic I WARNING The following applies only when the parking lights are connected and supported by the system 01 Engine tach signal is lost 02 N A II If the engine shuts down after a remote starter sequence Press and hold the Trunk button and the Start button at the same time for 2 5 seconds when using a 1 WAY remote OR Press once 1x on button 4 when using a 2 WAY remote The parking lights will ash four 4x times then will ash Y number times to indicate an error code See table 03 Foot brake is ON 04 Hood is open 05 Engine RPM limiter is ON 06 Glow plug timeout error 07 Vehicle is moving VSS 08 Check engine warning light is ON 09 Low fuel warning light is ON 10 N A 11 CAN communication failure during RS sequence www idatastart com Automotive Data Solutions Inc 2014 Page 20 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 moDuLe Diagnostics 1 OF 1 test moDuLe LeD 1 status Diagnostic I DURING PROGRAM
3. Press and hold programming button until LED 1 turns solid RED IN THE OPTIONS Press the programming button as many times as the option number indicates LED 1 will ash RED an equal amount of times continuously TO ACCESS THE SETTINGS Press and hold programming button until LED 1 turns solid GREEN LED 1 will ash GREEN as many times as the current or default setting number continuously IN THE SETTINGS Press the programming button as many times as necessary to access your setting LED 1 will ash GREEN an equal amount of times continuously To return to the MENUS exit the Module Navigation and redo the Module Navigation Procedure To save and return to the OPTIONS Press and hold programming button until LED 1 turns solid RED LED 1 will ash RED as many times as the current option number continuously Configure every other setting and proceed to step 13 MANDATORY EXIT MODULE NAVIGATION Press and hold programming button for 7 seconds LED 1 will ash RED rapidly Release programming button LED 1 will turn OFF Module navigation completed Failure to exit the Module Navigation will drain vehicle battery www idatastart com Automotive Data Solutions Inc 2014 Page 18 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 moDuLe navigation chaRt 1 OF 1 moDuLe navigation chaRt notes X menus Y oPtions Z settings I Default settings are listed in bol
4. OFF ACC ON START ON 03 04 ENGINE START STOP OFF ACC ON START OFF 05 gt gt VALET MODE PROGRAMMING PROCEDURE 1 OF 1 NOTE In Valet Mode the Remote starter is not functional Keyless entry Lock and Unlock will remain functional See RF kit user manual for alternate valet mode programming Time restriction Complete next step within 7 seconds Cycle ignition ON fi ve times 5x OFF ON rapidly Parking Light will ash once 1x Wait Parking Light will ash once 1x to indicate that the valet mode is ON or twice 2x to indicate that the valet mode is OFF Turn ignition to OFF position Valet Mode Programming Procedure completed To exit valet mode repeat steps 1 to 4 then START vehicle for 15 seconds www idatastart com Automotive Data Solutions Inc 2014 Page 16 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 gt gt 01 02 ENGINE START STOP OFF ACC ON START ON 03 04 05 06 gt gt 07 08 ENGINE START STOP OFF ACC ON START OFF 09 ENGINE START STOP OFF ACC ON START START START 10 AFTERMARKET REMOTE PROGRAMMING PROCEDURE 1 OF 1 WARNING Program aftermarket remotes before usage A maximum of four 4x aftermarket remotes per system Time restriction Complete next step within 7 seconds Cycle ignition ON fi ve times 5x OFF ON rapidly
5. carpet under driver seat A S Class PTS AT 07 13 CanH Black 02 pin 01 Brown Red DATA Behind carpet under driver seat A CanL Black 02 pin 02 Brown DATA Behind carpet under driver seat A S Class Diesel PTS AT 07 13 CanH Black 02 pin 01 Brown Red DATA Behind carpet under driver seat A CanL Black 02 pin 02 Brown DATA Behind carpet under driver seat A www idatastart com Automotive Data Solutions Inc 2014 Page 9 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 CONNECT TO VEHICLE START VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS STEP 1 TYPE 2 WIRING DIAGRAM 1 OF 2 MODULE 07 GRAY WHITE HOOD STATUS INPUT 08 GRAY BLACK NOT USED BLACK 2 PIN BLACK 20 PIN BLACK 6 PIN BLACK 6 PIN WHITE 6 PIN WHITE 6 PIN BLUE 6 PIN BLACK 10 PIN WHITE 10 PIN 1 TO CONNECT THE MODULE FOLLOW STEPS 1 TO 4 2 TO DISCONNECT THE MODULE FOLLOW STEPS 4 TO 1 IF NOT EQUIPPED WITH AN OEM HOOD SWITCH INSTALL AN AFTERMARKET HOOD SWITCH CONNECT TO MODULE RELAY B VEHICLE HARNESS A VEHICLE HARNESS B A STEP 2 WARNING CONNECT TO MODULE CONNECT IF REQUIRED HOOD SWITCH STEP 3 STEP 4 01 PINK RED CANH 02 PINK BLACK CANL CAN JUNCTION CONNECTOR CAN CONNECTORS C1 01 CANH 02 CANL SEE MODULE PROGRAMMING PROCEDURE PTS TO IDENTIFY THE REQUIRED CAN CONNECTOR ONCE IDENTIFIED DISCONNECT IT FROM THE CAN JUNC
6. checKList 2 OF 2 checKList 17 Exit vehicle 18 Close all doors 19 Press LOCK button three times 3x rapidly on the OEM keyfob to remote start vehicle 20 Wait for the vehicle to start Question 7 Is the vehicle equipped with a keyless authorization system Keyless Go YES Touch the exterior driver door handle to unlock door using the keyless authorization system Keyless Go Within 45 seconds go to step 21 NO Press UNLOCK button once 1x on the OEM keyfob Within 45 seconds go to step 21 21 Open driver door Question 8 Does the vehicle shut down YES The module does NOT detect the unlock signal from the vehicle communication network Call technical support NO Go to step 22 22 Enter vehicle Question 9 Is the vehicle equipped with a keyless authorization system Keyless Go YES Push vehicle start button once 1x Go to step 23 NO Insert key into ignition and turn key to ON position Go to step 23 23 Press and release brake pedal Question 10 Does the vehicle shut down YES Repeat this procedure from step 3 If the problem persists call technical support NO Go to step 24 24 Shut down the vehicle 25 Installation checklist completed www idatastart com Automotive Data Solutions Inc 2014 Page 15 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 gt gt 01 02 ENGINE START STOP
7. 3 10 8 11 13 14 12 15 17 18 19 20 16 6 4 1 2 5 3 6 4 1 2 5 3 6 4 1 2 5 7 9 3 10 8 11 12 6 4 1 2 5 2 1 3 4 4 2 8 1 3 5 7 10 9 6 MODULE BOX CONTENTS T HARNESS 1 2 PIN BLACK CONNECTOR AFTERMARKET HOOD SWITCH AND CABLE STICKER 1 EXPANSION PACK STICKER 2 EXTRA CONNECTOR HOUSING 10 PIN WHITE CONNECTOR 12 PIN BLACK CONNECTOR PROGRAMMING BUTTON LED 1 LED 2 LED LED RED BLUE BLACK BLACK RF PORT WEBLINK PORT BLACK BLUE BLACK BLACK TOP VIEW TOP VIEW BOTTOM VIEW BLACK USB BLUE TELEMATIC PORT WHITE BLACK EXPANSION PACK ASSEMBLY BLUE BLACK BLACK XP LED 1 XP LED 2 WEBLINK CABLE required accessory sold separately WEBLINK CABLE COMPUTER USB PORT 4 PIN BLACK CABLE ELECTRONIC IGNITION SWITCH REMOVAL TOOL accessory sold separately IGNITION SWITCH ADS TOOLS MB01 OR MERCEDEZ BENZ P N 639 589 01 07 00 MODULE WEBLINK PORT DOC 14281 www idatastart com Automotive Data Solutions Inc 2014 Page 4 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN COMPATIBLE ACCESSORIES 15 OF 15 RF KIT RF KIT Visit our website to see if this accessory is included with your product ANTENNA FLASH RF DECODER BEFORE INSTALLATION RF DECODER BLUE CABLE BLACK CABLE NC RED NC BLACK BLACK BLUE MODULE RF PORT TELEMATIC KIT accessories s
8. BENZ CL Class PTS AT 07 13 2 CL Class STD key AT 07 13 1 S Class PTS AT 07 13 2 S Class STD key AT 07 13 1 S Class Diesel PTS AT 07 13 2 S Class Diesel STD key AT 07 13 1 If equipped with a factory hood switch NOTES I This rmware covers Automatic Transmission AT vehicles only II All the covered Push To Start PTS vehicles are equipped with a keyless authorization system called Keyless Go www idatastart com Automotive Data Solutions Inc 2014 Page 2 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 www idatastart com Automotive Data Solutions Inc 2014 Page 3 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN BOX CONTENTS 1 OF 1 2 1 3 4 2 1 3 2 1 3 7 9 3 10 8 6 4 1 2 5 4 2 8 1 3 5 7 10 9 6 2 1 2 1 3 4 2 1 3 4 2 1 3 4 7 9
9. MING Flashing RED Missing wrong information from fi rmware or vehicle Solid RED Module waiting for more vehicle information Flashing GREEN Additional steps required to complete module programming Solid GREEN then OFF Module correctly programmed OFF No activity or module already programmed II DURING REMOTE START Flashing RED Module incorrectly programmed Solid RED Module incorrectly programmed Flashing GREEN Module correctly programmed and operational Solid GREEN then OFF Reset in progress OFF Invalid ground when running status from remote starter III WITH IGNITION OFF Flashing RED Module incorrectly programmed or connected Solid RED Module not programmed Waiting for more vehicle information Flashing GREEN False ground when running status from remote starter Solid GREEN then OFF Reset in progress OFF Module at rest and ready for a remote start sequence www idatastart com Automotive Data Solutions Inc 2014 Page 21 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 01 02 03 04 05 06 07 08 gt gt MODULE RESET PROCEDURE 1 OF 1 Disconnect all connectors from module except the BLACK 20 PIN connector Disconnect the BLACK 20 PIN connector PRESS AND HOLD programming button while connecting the BLACK 20 PIN connector Wait LED 1 will ash RED RELEASE programming button LED 1 will turn RED fo
10. N then will turn OFF Turn key to OFF position Remove key from ignition Module Programming Procedure completed www idatastart com Automotive Data Solutions Inc 2014 Page 12 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 gt gt gt gt 01 ENGINE START STOP STOP ACC ON START ON 02 03 gt gt gt gt 04 05 ENGINE START STOP STOP ACC ON START START 06 07 ENGINE START STOP STOP ACC ON START STOP 08 MODULE PROGRAMMING PROCEDURE PTS 1 OF 1 One of the connectors of the CAN junction connector controls the keyless authorization system Keyless Go The following procedure will allow the module to identify the required CAN connector Have the CAN junction connector accessible Identify every CAN connector whose CanH and CanL wires match the colors listed in the WIRE CHART LED 1 is solid RED Push start button to ON position Wait LED 1 will ash RED GREEN Disconnect the fi rst connector of the CAN junction connector whose CanH and CanL wires match the colors listed in the WIRE CHART Wait 5 seconds If the parking lights ash the required connector is found Connect it to the C1 connector as shown in the WIRING DIAGRAM and go to step 5 If the parking lights do NOT ash the required connector is NOT found Reconnect it to the CAN junction connector and repeat step 4 with another connector W
11. Revision Date 20140314 Document numbeR notice The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product be that either damage to the vehicle itself or to the installed device This device must be in stalled by a certified technician Please review the Installation Guide carefully before beginning any work beFoRe instaLLation 1 Connect module to computer 2 Login to Weblink account 3 Flash firmware to module module is not preloaded with firmware 4 Use accessories accordingly accessories are sold separately instaLL guiDe AKX IDS RS BZ1B ADS BZ1 EN haRDwaRe ADS BZ1 FiRmwaRe AKX IDS RS BZ1B ADS BZ1 www idatastart com Automotive Data Solutions Inc 2014 accessoRies ADS USB REQUIRED COMPATIBLE RF KIT OPTIONAL DIRECTED SMARTSTART amp ADS HRN RS SM01 OPTIONAL ADS TOOLS MB01 OPTIONAL 14281 VEHICLE LIST 1 OF 1 MAKE MODEL YEAR INSTALL TYPE FEATURES REMOTE START FROM OEM REMOTES SECURE TAKEOVER DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK HATCH RELEASE PARKING LIGHT CTRL HEATED SEATS CTRL VENTILATED SEATS CTRL RAP SHUTDOWN CTRL TACHOMETER STATUS MONITORING BRAKE PEDAL STATUS MONITORING VSS STATUS MONITORING GLOW PLUG STATUS MONITORING DOOR STATUS MONITORING TRUNK STATUS MONITORING HOOD STATUS MONITORING MERCEDES
12. TION CONNECTOR AND CONNECT IT TO C1 REFER TO WIRE CHART REFER TO COMPONENT LOCATOR IF THE REQUIRED CAN CONNECTOR DOES NOT FIT IN C1 SEE NEXT PAGE FOR INSTRUCTIONS CONNECT CONNECT www idatastart com Automotive Data Solutions Inc 2014 Page 10 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 01 CANH 02 CANL TYPE 2 WIRING DIAGRAM 2 OF 2 1 RELEASE RETAINING CLIP OF CAN CONNECTOR REMOVE CAN WIRES FROM HOUSING 2 RELEASE LOCKING MECHANISM 3 INSERT EMPTY HOUSING IN CAN JUNCTION CONNECTOR TO AVOID LOSING IT 4 INSERT CAN WIRES IN PROVIDED HOUSING CONNECT IT WITH C1 HARNESS AS SHOWN IN WIRING DIAGRAM INSTRUCTIONS TO CHANGE THE HOUSING OF CAN WIRES ONLY IF THE CAN CONNECTOR DOES NOT FIT IN C1 www idatastart com Automotive Data Solutions Inc 2014 Page 11 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 01 OFF ACC ON START 02 OFF ACC ON START 03 gt gt 04 OFF ACC ON START 05 06 OFF ACC ON START 07 MODULE PROGRAMMING PROCEDURE STD KEY 1 OF 1 LED 1 is solid RED Insert key into ignition Turn key to ON position Wait LED 1 will turn solid GREEN then will turn OFF WARNING If LED 1 ashes RED GREEN turn ignition to OFF position The vehicle is PTS Follow appropriate PTS sections START vehicle for 15 seconds LED 1 will turn solid RED Wait LED 1 will turn solid GREE
13. Turn OFF the vehicle Verify all keyfob functionalities Door Lock Door Unlock Trunk Release and RFID access if equipped Insert the expansion pack in the module Connect the module to the computer with the programming cable WEBLINK port Flash the module with the latest fi rmware then ash the expansion pack Connect and secure every connector to the vehicle as shown in STEP 1 of the WIRING DIAGRAM WARNING Any vehicle harness that is disconnected during installation must be re connected before performing any system tests Failure to comply will result in vehicle displaying error messages An OEM scantool will be required to clear the error messages START the vehicle Verify all vehicle functionalities WARNING If the vehicle displays error messages or any malfunction stop the installation verify every connection and if the problem persists call technical support Turn OFF the vehicle Connect every connector to the module as shown in STEP 2 of the WIRING DIAGRAM Connect every other connector to the module as shown in STEP 3 of the WIRING DIAGRAM If the vehicle is not equipped with a factory hood switch install an aftermarket hood switch as shown in STEP 4 of the WIRING DIAGRAM If required connect a compatible RF Kit to the RF port of the module If required connect a compatible Telematics Device to the TELEMATIC port of the module Put sticker 1 on a clean and visible surface in the en
14. ait LED 1 will turn solid GREEN then will turn OFF START vehicle for 15 seconds LED 1 will turn solid RED Wait LED 1 will turn solid GREEN then will turn OFF Push start button to OFF position Module Programming Procedure completed www idatastart com Automotive Data Solutions Inc 2014 Page 13 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 instaLLation checKList 1 OF 2 checKList 01 WARNING Vehicle engine will start many times Test in a well ventillated area 02 Open driver door window for easy vehicle access 03 Enter vehicle Start the vehicle and let it run for 15 seconds 04 Stop the vehicle and exit vehicle 05 Close all vehicle doors hood and trunk 06 Press LOCK button three times 3x rapidly on the OEM keyfob to remote start vehicle Question 1 Does the vehicle remote start YES Go to step 7 NO The module doesn t detect OEM remote lock button from the vehicle communication network Check all connections repeat step 6 and call technical support if the problem persists 07 Press LOCK button three times 3x rapidly on the OEM keyfob to shut down vehicle Question 2 Does the vehicle shut down YES Go to step 8 NO Repeat step 7 If the problem persists unlock the door using the OEM keyfob enter vehicle and press brake pedal to shut down the vehicle and call technical support 08 Open hood Question 3 Is the orange warn
15. d 01 CONFIGURATION 01 DISARM UNLOCK BEFORE START 01 oFF II Make sure the option is covered on the vehicle before attempting to change the setting 02 ON 02 RELOCK AFTER START 01 oFF 02 ON 03 RELOCK AFTER SHUTDOWN 01 oFF 02 ON 04 FORCE UNLOCK ALL ON FIRST PRESS 01 oFF 02 ON 05 TAKEOVER 01 enabLe 02 DISABLE 06 SECURE TAKEOVER DELAY 01 45 sec 02 90 SEC 03 03 MIN 04 04 MIN 07 FACTORY KEYLESS RS SEQUENCE 01 DISABLE 02 N A 03 LOCK UNLOCK LOCK 04 LocK LocK LocK 08 MODULE RUN TIME 01 03 MIN 02 05 MIN 03 10 MIN 04 15 MIN 05 25 MIN 06 30 MIN 07 35 MIN 08 15 min 09 WAIT TO START DELAY 01 02 sec 02 05 SEC 03 08 SEC 04 10 SEC 05 15 SEC 06 20 SEC 07 25 SEC 08 30 SEC 10 15 N A 01 N A 02 07 Technical Support only 01 N A 01 N A Vehicle will shutdown when a door is opened www idatastart com Automotive Data Solutions Inc 2014 Page 19 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 Remote staRteR eRRoR coDes 1 OF 1 Remote staRteR eRRoR coDes notes X numbeR oF PaRKing Light FLashes Diagnostic I WARNING The following applies only when the parking lights are connected and supported by the system 01 Engine running 02 Key in ignition at ON position II After a remote starter failure the parking lights will ash three 3x times then will
16. gine bay and put sticker 2 under the dashboard near the OBDII connector Module installation procedure completed www idatastart com Automotive Data Solutions Inc 2014 Page 7 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 TYPE 1 WIRING DIAGRAM 1 OF 1 CONNECT TO VEHICLE START VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS STEP 1 MODULE 07 GRAY WHITE HOOD STATUS INPUT 08 GRAY BLACK NOT USED BLACK 20 PIN BLACK 6 PIN BLACK 6 PIN WHITE 6 PIN WHITE 6 PIN BLUE 6 PIN BLACK 10 PIN WHITE 10 PIN 1 TO CONNECT THE MODULE FOLLOW STEPS 1 TO 4 2 TO DISCONNECT THE MODULE FOLLOW STEPS 4 TO 1 IF NOT EQUIPPED WITH AN OEM HOOD SWITCH INSTALL AN AFTERMARKET HOOD SWITCH CONNECT TO MODULE RELAY B VEHICLE HARNESS A VEHICLE HARNESS B A STEP 2 WARNING CONNECT TO MODULE CONNECT IF REQUIRED HOOD SWITCH STEP 3 STEP 4 BLACK 2 PIN NOT USED www idatastart com Automotive Data Solutions Inc 2014 Page 8 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 TYPE 2 WIRE CHART 1 OF 1 MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR MERCEDES BENZ CL Class PTS AT 07 13 CanH Black 02 pin 01 Brown Red DATA Behind carpet under driver seat A CanL Black 02 pin 02 Brown DATA Behind
17. ing sticker Sticker 1 placed under the hood YES Leave hood open and go to step 9 NO Put the mandatory orange warning sticker Sticker 1 leave hood open and go to step 9 09 Close all doors 10 Press LOCK button three times 3x rapidly on the OEM keyfob to remote start vehicle Question 4 Does the vehicle remote start YES Press LOCK button three times 3x rapidly on the OEM keyfob to shut down vehicle Go to question 5 NO Go to step 11 Question 5 Is the vehicle equipped with a factory hood switch Inside hood latch YES The module does NOT detect the hood signal from the vehicle communication network Call technical support NO Install the mandatory hood switch included in the kit Repeat installation checklist 11 Close hood 12 Enter vehicle Do NOT press brake pedal 13 Close all doors 14 Press LOCK button three times 3x rapidly on the OEM keyfob to remote start vehicle 15 Wait for the vehicle to start 16 Press brake pedal Question 6 Does the vehicle shut down YES Go to step 17 NO The module does NOT detect the brake pedal signal from the vehicle communication network Press LOCK button three times 3x rapidly on the OEM keyfob to shut down vehicle and call technical support www idatastart com Automotive Data Solutions Inc 2014 Page 14 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 instaLLation
18. old separately NC NC NC DIRECTED SMARTSTART ADS HRN RS SM01 MODULE TELEMATIC PORT DOC 14281 technicaL note 1 OF 1 imPoRtant instaLL viDeo gaLLeRY avaiLabLe onLine Before installing this product consult our Install Video Gallery and watch Vehicle Disassembly Procedure videos Module Connection Procedures videos Module Programming Procedures videos Simply visit our forum and register at http www 12voltdata com forum viewtopic php f 340 amp t 9683 amp sid a61772b486e4584ad6f058b171ffa425 www idatastart com Automotive Data Solutions Inc 2014 Page 5 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 A COMPONENT LOCATOR 1 OF 1 inteRioR view DRiveR siDe view PassengeR siDe view www idatastart com Automotive Data Solutions Inc 2014 Page 6 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281 01 ENGINE START STOP OFF ACC ON START START START 02 ENGINE START STOP OFF ACC ON START OFF 03 04 05 06 07 08 ENGINE START STOP OFF ACC ON START START START 09 10 ENGINE START STOP OFF ACC ON START OFF 11 12 13 14 RF 15 16 17 MODULE INSTALLATION PROCEDURE 1 OF 1 START the vehicle Verify all vehicle functionalities If the vehicle displays error messages or any malfunction stop the installation and service the vehicle
19. r 2 seconds Module RESET completed Reconnect all connectors Repeat programming procedure Failure to follow procedure may result with a DTC or a CHECK ENGINE error message www idatastart com Automotive Data Solutions Inc 2014 Page 22 oF 22 20140314 AKX IDS RS BZ1B ADS BZ1 EN DOC 14281
Download Pdf Manuals
Related Search