Tornado Manual pdf
Contents
1. Common Feed Connection factory default Enclosure and projector share the same electrical circuit Circuit must be powered ON 24 7 Connect incoming power to the terminals labeled MAINS E Earth Ground L Live N Neutral Cyclone Enclosure User Manual page 19 amp TEMPEST 4 Digital Enclosure Control DEC3 3 with Goldilocks Relay Temp L Lamp TEMPEST DEC3 3 that s Digital Enclosure Control third Generation revision 3 is the brain of your Tempest enclosure It will maintain the internal environment in a comfortable temperature and humidity range and prevent condensation the real killer of outdoor equipment DEC3 3 monitors internal temperature humidity and lamp current at all times and uses this information to control the enclosure s lamp relay fan s and heater s It can report back over the DMX cable using the RDM protocol Remote Device Management if desired From summer 2013 DEC is running Tempest s new Goldilocks operating system patents pending A completely new OS Goldilocks analyzes temperature and humidity trends targeting and maintaining safe ranges and acting to prevent condensation before it happens Goldilocks is also much more energy efficient than previous generations so your equipment is always in the Goldilocks zone and you save money too Cyclone Enclosure User Manual page 20 TEMPEST 4 DEC3 3 Schematic O Optional2. To UNLOCK hold ESC and OK together for 5 seconds Lm LLJ O gt LLI La You are in the CONTROL MENU Use to scroll up and down the menu Press OK to enter a menu item Use to set the item parameter or to scroll to the next menu level Use ESC to go BACK and OK to confirm settings To LOCK hold ESC for 5 seconds Menu will time out after ten minutes Tornado Enclosure User Manual page 29 i TEMPEST Control Menu SET DMX OPTIONS SET DMX MODE From the Front Panel this menu item allows the user to check and if necessary change the RDM mode BASIC Standalone operation no DMX RDM factory default MONITOR Standalone plus support for RDM remote configuration and monitoring CONTROL Monitor plus use of a single DMX slot to control Lamp relay SERVICE Monitor plus use of three DMX slots to control Lamp Heater and Fan Important Please ensure that the DEC3 3 is NOT left in Service Mode SET DMX ADDRESS in Monitor Control or Service modes Select a DMX starting address in the range 001 to 510 1 Lamp Relay In Service Mode an addition two slots are available 2 Fan Duty Control 3 Heater Duty Control Note that the DMX control is designed using a SAFETY pile on Logic So the DMX input can only override automatic settings within safe limits SET DMX CURVE DMX Curves affect the way the fixture relay is controlled in Control Mode DMX levels are shown a
3. and a log of RDM messages This RDM interface provides a graphic view of the various sensor functions supported by DEC3 2 and up Important Check that your RDM interface vendor has tested his interface with Tempest enclosures and all other RDM devices you plan to use on the same network DEC3 3 firmware is field upgradeable using RDM A field upgrade requires a JESE RDM TRI MKT interface to be connected to the Remote Device Manufacturer DEC3 MK2 Controller Software Version 00 12 DMX network on which the DEC3 3 is located and the use of JESE GetSet File Select Select a file to upload 0 software The kit is available from Tempest under part 4 2000 190 page 33 4 TEMPEST 4 TEMPEST 5 Mounting the Luminaire Do not attempt to mount the luminaire with only a single person Remove the globe and place it in a safe location T u Follow the instructions below for different luminaire types Plug the luminaire into the power receptacle in the enclosure and then connect the DMX cables to the luminaire Tie down cables to the luminaire or enclosure base so that they will not come into contact with the heater or fans at any point Tornado Enclosure User Manual page 34 4 TEMPEST Tornado 1900 1950 Mount the luminaire on its omega clamps on the fixture mounting Bracket Note Depending on the size of the fixture base
4. and cleaned on a regular basis To remove filters pull them directly out of their grooves The filters can be cleaned by running water from a hose and do not require any special solution To reinstall push filter back into place between the top and bottom base covers Case and Globe As Needed The outside of the case and globe should be cleaned as needed Outside inspection should give you a good idea of when this is necessary The case should be cleaned with a wet cloth and mild detergent if necessary Do not use a direct spray from a hose to clean the case The globe can be Tornado Enclosure User Manual page 45 amp TEMPEST cleaned with any mild cleaner It is also acceptable to treat globe with a product that keeps rain from adhering to its surface DO NOT USE hydrocarbon based cleaners on the globe under any circumstances They can severely damage the globe material Luminaire Review the manufacturer s instructions for proper maintenance of your luminaire Remember the enclosure simply protects the luminaire and is not a substitute for regular maintenance Tornado Enclosure User Manual page 46 amp 4 TEMPEST 9 Troubleshooting This is a guide to the general symptoms problems and solutions that may occur during the lifetime of your enclosure However it is important to remember that problems may occur within the luminaire itself and these must also be considered Luminaire does not have power e Check power
5. independent SPLIT AC Luminaire Supply Cut links on board for split feed operation MAIN AC Supply amp 4 TEMPEST SENSOR AC HEATER S AC FAN S OUT IN OUT IN DMX RDM RS485 Cyclone Enclosure User Manual page 21 amp TEMPEST DEC3 3 Main Functions Sense current to luminaire lamp on off Record lamp hours Monitor temperature and humidity inside Enclosure Maintain temperature at safe operating level Maintain relative humidity within safe limits Prevent condensation Isolate luminaire in case of unsafe temperature Report status over RDM CON O uUi BR UU N Optional remote luminaire relay control over DMX DEC3 3 constantly monitors the following parameters e Luminaire Luminaire power e Line Voltage e Temperature e Humidity DEC 3 3 s patented Goldilocks algorithm uses a combination of heaters and fans to maintain a safe operating temperature and a safe relative humidity level that will not allow condensation to take place As air is heated it is able to support more moisture without condensing so Goldilocks uses heat to raise the air temperature inside the enclosure in the event that relative humidity approaches dewpoint Factory Settings Basic Mode In most applications DEC3 3 will operate correctly with its factory default settings in Basic operating mode You do not need to do anything Please skip to the Power Connections section b
6. it may be easier to remove the fixture bracket before attaching the omega clamps and luminaire Omega Clamp Fixture Mounting Bracket Tornado Enclosure User Manual page 35 4 TEMPEST Tornado 2000 2100 2200 2300 Fixture Tray Use the keyholes to mount Robe fixtures without Omega Clamps Use either the vertical or horizontal slots for Omega Clamp and VL clamp bracket fixings Use the obrounds to mount Martin MAC3 direct to the Fixture Tray L EJ n Remove the Fixture Tray by removing the four 5 16 mounting bolts Tornado Enclosure User Manual page 36 4 TEMPEST Luminaires with Omega Clamps This applies to most luminaire types Remove the Fixture tray from the enclosure as shown above Mount the Omega clamps securely onto the fixture base Make sure that the fasteners lock positively in place 3 Boltthe clamps to the fixture tray using the Omega Clamp Spacers and the bolts provided CHECK THAT THE FIXTURE IS CENTERED ON THE FIXTURE TRAY 4 Replace the fixture tray fixture assembly in the enclosure and bolt firmly in place Diagram Mounting with Omega Clamps and Clamp Spacers Omega clamp Fixture Fixture Tray Tray Bolts Tornado Enclosure User Manual page 37 amp 4 TEMPEST Vari Lites and the Vari Lite Hook Bracket Vari Lites are provided with a Hook Bracket in place of an Omega Clamp 1 Attach the Hook Bracket to the VL fixture feet foll
7. plus 150 watts e Supply must be permanently ON Split feed e Enclosure power must be permanently ON e Luminaire power may be switched off e Enclosure power must be rated for 1150 watts e Luminaire power must be rated for the luminaire see luminaire manual e Luminaire and enclosure power must be same voltage Either way the enclosure must be powered 24 7 in order to protect the luminaire inside against condensation and extremes of temperature Since the enclosure heater s never operate when the projector fixture lamp is on it is NOT necessary to rate the power service for the SUM of the enclosure and the projector light fixture IMPORTANT Tempest enclosures are supplied for either 120VAC 50 60Hz or 208 240VAC 50 60Hz operation Tempest Lighting is not liable for damage or failure to operate correctly due to connection to an inappropriate electrical supply ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A QUALIFIED ELECTRICIAN IN COMPLIANCE WITH LOCAL NORMS AND STANDARDS Cyclone Enclosure User Manual page 18 Split Feed Connections Cut here for split supply operation GPOBSTOSSOSOCOLOS Fani Proi rojector Fan2 receptacle Heater s Projector Supply Enclosure Supply split mode 100 250VAC 50 60Hz Note wire colors may differ depending on applicable electrical standards European wire colors are shown here IMPORTANT MAKE SURE THAT TERMINAL SCREWS ARE FULLY BACKED OUT BEFORE INSERTING WIRES
8. power at all times It is an active climate controlled enclosure and will not provide proper protection for the luminaire inside if it is not connected to AC power Unless the enclosure or luminaire is undergoing routine maintenance the globe should be in place and locked down at all times Only authorized personnel should open the enclosure see maintenance warnings in the next section If the ambient temperature is high enough the over temperature shutdown feature may engage and temporarily cut off power to the luminaire Once the temperature reaches acceptable levels power will be automatically restored Do not routinely operate luminaire in full sun in warm weather Black luminaires absorb a significant amount of energy from the sun and may overheat in these conditions The enclosure has not been designed to protect the luminaire when running in this kind of extreme condition outside lighting is generally used at night Tornado Enclosure User Manual page 44 TEMPEST 8 Routine Maintenance It is very important to perform routine maintenance on both the enclosure and the luminaire within Failure to do so may reduce lifetime for both the enclosure and the luminaire Note Maintenance schedules depend on location and environment The times given here are general guidelines for you to use It is up to you to judge whether maintenance should be done more often We do advise doing these tasks no less often than mentioned here Sa
9. switch of luminaire Note the following actions should be performed by a licensed electrician If power is on check wiring including metering supply voltages enclosure must receive 200 240VAC to operate properly If LEDs on the DEC3 control panel controller are lit check the Lamp Relay LED If it is on meter power in receptacle If no power is present at the receptacle contact technical support e IfDEC controller is set to DMX mode check that a DMX address has been set and that the DEC is receiving a valid DMX signal with the appropriate channel HIGH e f using SPLIT POWER FEEDS check that both the MAIN and SPLIT feeds are energized e Incase of over temperature the power disconnection is an intended function of the enclosure and is for the protection of the luminaire which is not meant to operate in extreme conditions In this case the problem will only continue until temperature drops to acceptable levels It is possible that the air intake or exhaust has become clogged leading to higher temperatures inside the enclosure Make sure that these areas are clear the filters are clean and the fans are working properly Luminaire turns on and off repeatedly e Check that vent areas and airways are clear If so ambient temperature may be too high see over temperature note above or luminaire may have internal problem Luminaire does not respond to DMX signal e Make sure that luminaire has power If so check DMX wiring If not se
10. tool to open the enclosure Marine Latch Designs vary slightly by model Cyclone Enclosure User Manual page 9 TEMPEST 2 Installation Safety and Warnings d Read the Manual before installing the enclosure da Read the manual before opening or servicing the enclosure ka Never leave the enclosure unattended when open da Ensure all bolts and terminals are tight and clean e Do not touch the heater unless you can be sure that it is cool d Observe all warning labels in the enclosure itself M Do not open any electrical boxes until power is off M Do not open the enclosure in wet weather Never move the enclosure with the luminaire inside Never handle the enclosure by the globe Always lift the enclosure from under the base Cyclone Enclosure User Manual page 10 amp 4 TEMPEST Planning Snow clearance MINIMUM 24 60c U Enclosure must be powered 24 7 365 Warning This installation cannot be safely completed by 1 person Mounting Tornado 1900 1950 D Each Enclosure must be wall floor or ceiling mounted with the two stainless steel brackets provided D Tempest Lighting recommends only stainless steel mounting hardware for permanent installation outdoors Floor Wall or Ceiling Mounting pu Use the two stainless steel mounting brackets provided _ g with the Tornado 1900 1950 LO Fix the holes in the bracket feet to secur
11. E WA TEMPEST Heater Fan Relay Temp DMX Lamp amp TEMPEST SOY amp Tempest Lighting Inc For the following products manufactured after 13110 Saticoy Street Unit C August 2013 N Hollywood CA 91605 USA Tel 1 818 787 8984 Tornado 1900 1950 Fax 1 818 982 5510 Tornado 2000 2100 Tornado 2200 2300 Tornado 2400 www tem pest org With DEC3 3 Goldilocks rev 0 01 006 or higher 3 it is subject to change without le for expense or injury In the interest of continuous product ir notice Neither Tempest Lighting Inc arising from it Tempest Lighting Inc All Rights Resei September 2013 Table of Contents TTS OCU c se 6 D OMEN e esa 7 se 10 CLG q q tmm 11 Mounting Tornado 1900 1950 sese sese 11 Mounting Tornado 2000 and 12 Orientation Guidelines eene eene enne nennen nnn nnns 14 Big Utah jo o T tp ea ee csc 15 Installation above public Spaces eee 16 UTs Ts PRN RR ONES DRA NUR DO DER NU 17 Conduit entry holes 17 One or TWO Power saiem bedio musa ddnaoscuissneusaiiimp sediada 18 Digital Enclosure Control DEC3 3 with Goldilocks 20 as di cal a 21 EIS qq Main CONS MOM 22 F
12. ST Shorter Luminaires Requiring Bracket Standoffs In order to align the center of the luminaire correctly in the Tornado enclosure some fixtures need the Fixture tray to be raised This is done with tubular standoffs that insert between the Fixture Tray and the enclosure Base The installation procedure is the same as for any of the above except that the fixture standoffs must be inserted when the Fixture Tray is remounted If the fixture you specified when you ordered your Tornado enclosure requires bracket standoffs they will have been supplied If none are supplied your fixture does not require them Diagram Fixture Tray Standoffs Use longer bolt i provided il Fixture Tornado Enclosure User Manual page 40 4 TEMPEST Mounting the Luminaire Tornado 2400 The Tornado 2400 is designed to house the Barco High End Systems Showgun Showbeam Showpix and DL3 luminaires all of which have the same base The Tornado 2400 is supplied with two heavy duty mounting brackets which bolt to the extruded clamps supplied with the Showgun Showbeam DL3 fixture Mount the clamps to the enclosure brackets then set the fixture on the clamps and secure using the quarter turn fasteners provided Note DML1200 Fixture When the Tornado 2400 is specified for the Barco DML1200 it will be supplied with a custom fixture mounting plate that bolts directly into the fixture base Tornado Enclosure User Manual pa
13. TICE All safety instructions provided by the luminaire manufacturer must be followed carefully Failure to do this may void both the luminaire and the enclosure warranties When working at heights or in awkward locations it is imperative to develop a safety plan based on the information in this manual and on local conditions and safety regulations The safety plan must be approved by the site engineer safety officer as appropriate to local conditions NEVER attempt to install Tornado enclosures in high winds or when precipitation is present or imminent Cyclone Enclosure User Manual page 6 7 TEMPEST Dimensions CAD drawinas in DWG and PDF format are available for download at www tempest or Tornado 1900 Tornado 1950 Power Entry CE Bs Data Entry Tornado 2000 2100 Base Down Base Up Horizontal 672 6 47 632 JE 35 78 457 18 00 ower and Data Conduit entries Cyclone Enclosure User Manual page 7 TEMPEST Tornado 2200 2300 Base Down Base Up Horizontal 4 2 RS 782 3079 Conduit entries Tornado 2400 Cyclone Enclosure User Manual page 8 TEMPEST Note Draw Latch Clearance Allow adequate clearance for all latches 3 75mm Note Tornado 2400 may be installed base up or base down only Note Marine Latches Marine Latches require a
14. actory Settings Basic Mode sese sese ee 22 Operating MO QGS i sicesisvania uir i 23 DEC3 3 Control Parameters sees eee eee eee 24 Start up VAGA IO dana 25 ade 25 Remote Device Management RDM 27 einge Mie ao S 28 RDM Monitoring and Configuration sss sese sss sese ee eee eee eee 32 Firmware Upgrade over RDM cccscccsseecseeeeseeceseeeeeeseseecaeeeeeeetaeeeeaeetaues 33 Mounting the 34 Tornado 190051930 itcm 35 Tornado 2000 2100 2200 2 300 estie eo obse 36 Vari Lites and the Vari Lite Hook 38 Martin MAC and other tall 39 Shorter Luminaires Requiring Bracket Standoffs 40 Cyclone Enclosure User Manual J TEMPEST page 2 TEMPEST Mounting the Luminaire Tornado 2400 41 6 Closing up the Enclosure 42 DO Dera Rn 44 8 Route TH e Ta Gomes seieuaeps bein doses 45 9 Troubleshooting E TL m LEES 47 Limited nennen nnnm nennen nnn rena nnn nna na 49 II T mpestProduct SUD PONT iiri
15. e above Fans are not spinning e Fan cords may have become disconnected Check connections between fan and cord e Fans may be obstructed Shut off power to enclosure and check for obstructions Turn power back on to see if fans will start spinning If fans do not turn and display on temperature controller is lit contact technical support If fans do not turn display is not lit then enclosure is not receiving power Turn off all power and check wiring If the wiring is correct contact technical support Excessive debris in unit e Filter may not be fully pushed into groove Make sure that it is in place around the whole unit Excessive water in enclosure e Weep drain holes may be clogged Clear them Tornado Enclosure User Manual page 47 TEMPEST Latches do not latch properly e Closure of globe may be obstructed Check to make sure seals are clear before replacing globe Tornado Enclosure User Manual page 48 TEMPEST 10 Limited Warranty All sales are subject to the company s Standard Terms and Conditions available for download at www tempest org The following is an extract INSPECTION WARRANTY RETURNS A Customer at its sole expense shall inspect all Goods promptly upon receipt and accept all Goods that conform to the specifications or catalog All claims for any alleged defect in or failure of the Goods or Seller s performance to conform to the Contract capable of discovery upon reasonable
16. e contact Tempest Lighting 13110 Saticoy Street North Hollywood CA 91605 USA Tel 1 818 787 8984 Fax 1 818 982 5582 info tempestlighting com Visit our web site for current information and specifications www tempest org Tornado Enclosure User Manual page 50
17. e structure using i ais 3 T 3 8 M10 stainless steel hardware not supplied Pole Mounting To mount to the top of a pole fabricate a plate E with four 0 434 11mm holes and weld to the top of your pole Use these dimensions 6 152mm 15 5 394mm Cyclone Enclosure User Manual page 11 i amp TEMPEST Pipe Mounting Pipe Clamps 4900 MCT Pipe clamp for pipes 1 5 38mm to 2 50mm OD Order TWO per enclosure 4925 MCT Pipe clamp for pipes 2 50mm to 2 5 64mm OD Order TWO per enclosure 2 U Pipe Clamps mount to the enclosure base in the same locations as the mounting brackets provided NOTE Chesboro style half couplers may be used for temporary installations but are not recommended for permanent installs Mounting Tornado 2000 and up Each Enclosure must be mounted with FOUR points Tempest Lighting recommends only stainless steel mounting hardware The bolts attaching the enclosure to its shipping pallet are mounting bolts Do not Discard 00009 All mountings must be made using the two Unistrut channels on the base of the enclosure Pipe Mounting Pipe Clamps 4900 MCT Pipe clamp for pipes 1 5 38mm to 2 50mm OD Order FOUR per enclosure 4925 MCT Pipe clamp for pipes 2 50mm to 2 5 64mm OD Order FOUR per enclosure e 0 S Em Note These parts are supplied with the Tornado enclosure Cyclone Enclosure User Man
18. elow If your needs are more complex read on Cyclone Enclosure User Manual page 22 TEMPEST Operating Modes DEC3 3 may operate in one of four modes set using either the Front Panel or by RDM control In all configurations the luminaire inside the enclosure may also be an RDM enabled device Basic Mode factory setting e Standard temperature settings e DMX and RDM disabled e Best for standalone operation Monitor Mode e As Basic mode plus e status reporting e RDM configuration settings may be changed remotely or at the enclosure control panel e DEC3 3 does not require a DMX signal to operate Control Mode e As Basic mode plus e Enclosure functions as a 1 channel DMX device with remote control of the lamp relay o DMX level gt 75 enables normal relay operation normally ON o DMX level lt 25 disables normal relay operation relay turns OFF o This allows you to force a hard reset of the lamp relay in the event of a luminaire malfunction e Control mode is recommended for show control applications but can be risky in live show operation since the DMX slot used for the enclosure MUST be kept high to prevent the lamp relay from opening Service Mode e For trained service personnel only e Normal operation is suspended and the enclosure functions as 3 channel DMX device o Lamp Relay Slot 1 o Fans Slot 2 o Heater Slot 3 e Service mode is ONLY for troubleshooting DO NOT
19. en enclosure ventilation fails with the lamp on in which case the temperature will rise very quickly To avoid nuisance tripping we recommend setting a higher Trip temperature 60 C or above SET MAX HUMIDITY default 8096 permissible range 50 90 Set target maximum relative humidity level This should be set at or a few higher than the normal high humidity levels expected on site SET LAMP ON POINT The lamp current at which DEC detects the luminaire luminaire lamp is running Default is 1 Amp which allows for equipment fans and power supplies to run without changing the air in the enclosure Lamp on point may be set in 0 2 Amp increments between 0 2 Amps and 2 0 Amps RESET LAMP HOURS Reset each time you change the lamp in the luminaire luminaire Make this a part of your maintenance instructions Tornado Enclosure User Manual page 31 STATUS DISPLAY View current status information using the arrow keys to scroll through a b C d e f g Humidity relative humidity in 96 Air temperature in degrees C or F 4 TEMPEST PCB temperature this will usually be significantly higher than air temperature Voltage line Voltage reaching the DEC Current being drawn by luminaire light in Amps Lamp Hours elapsed since last reset Firmware version RDM Monitoring and Configuration All the features accessible over the DEC3 3 control panel are also available over RDM Just how this information i
20. erature is HIGH and Fan is cooling enclosure Short burst when lamp off indicates fan moving air to stabilize temp humidity Current sensing shows lamp is ON Lamp hour counter is running Current sensing shows lamp is OFF Lamp hour counter is not running Lamp relay is closed normal Luminaire power receptacle is energized Lamp relay is open due to over temperature event Luminaire power receptacle is isolated Temperature is below lower temp setting Temperature is in normal range Humidity is above target limit Temperature is above top setting Temperature is above Trip level Luminaire power is isolated DEC3 3 is in BASIC Mode DMX not used OR DEC3 3 is in Monitor or Control Mode and no valid DMX or RDM packet has been detected Good DMX or RDM data packet received Control Mode DMX Fail A previously good DMX signal has failed Monitor Mode No RDM information being received this is normal page 28 amp TEMPEST Control Display The display on the Control display provides additional status information depending on the operating mode Basic Mode amp 28 4796 internal temperature relative humidity Monitor Mode 209V OFF line voltage lamp status DMX Mode amp 28 4796 internal temperature relative humidity Service Mode 209V OFF line voltage lamp status Alternating with DMX 001 DMX Start Address No DMX DMX Status Control Interface Operation The Control Interface is normally LOCKED
21. fety d Although maintenance can be performed while the enclosure is powered it is safer to carry it out with the power disconnected with proper lockout and tag out procedures followed d Be aware that once the enclosure has had power applied to it the heater will get hot and the fans will start to turn Make sure that your hands are clear of these areas before applying power to the enclosure Only authorized personnel should perform maintenance on the enclosure or luminaire Do not service the unit in the rain or other adverse weather conditions snow sleet high winds etc Be aware that the globe is large object that can be awkward to handle especially when standing on a ladder or scaffolding Inspection Checklist Every Three 3 Months All weep drain holes should be clear All vents should be free of debris Enclosure should be free of debris both inside and out Bolts should be tight All safety cable should be in good condition Lid seal should be in good condition Check seal inside and out for gaps Globe should not be cracked Fans should be moving it will be necessary to have the power to check this with corresponding indicator status Except for the last two items concerning globe and fan problems with any of these things can be easily remedied Contact technical support for problems with the last two items Air Filters Every Three 3 Months The air filters all around the base should be removed
22. ge 41 6 Closing up the Enclosure 606002006 20000066 1 Check all electrical connections 2 Clear the enclosure and luminaire of all dust and debris 3 Checkthat the power switch on the luminaire is in the ON position 4 Complete DMX control connections following luminaire manufacturer s instructions 5 Test luminaire 6 Safety cable the luminaire to the Fixture Tray leg horizontal and vertical enclosures 7 Tie down cables to luminaire or mounting brackets so that they will not touch heaters or fans 8 Replace the globe assembly on the Tornado base This requires two people TEMPEST Tornado Enclosure User Manual page 42 4 TEMPEST Securing the Globe to the Tornado Enclosure Base 1 Using two people lift the globe assembly in place 2 As soon as the globe assembly is in place secure the four latches and insert padlocks in the locking rings if required for additional security 3 IMPORTANT The latch tension is adjustable and has been set in the factory to assure a secure and weathertight seal Check to make sure the tension is maintained Tension adjustment screw and locknut ock not supplied for additional security if desired Latch properly secured with a caribiner in place Congratulations Your system is now ready to check out Tornado Enclosure User Manual page 43 TEMPEST Operation e O Enclosure must receive
23. inspection must be set forth in a written rejection notice detailing the alleged non conformity and be received by Seller within thirty 30 calendar days of Customer s receipt of the Goods Failure by Customer to notify Seller of the alleged non conformity within thirty 30 days will be conclusive proof that the Goods have been received by Customer without defects or damage and in the quantities specified on the bill of lading and shall constitute an irrevocable acceptance of the Goods and a waiver of any such claim in connection with the Goods B Seller warrants to Customer only that the Goods will be free from defects in material and workmanship at the time of delivery and subject to the exceptions and conditions set forth below for the following period the Warranty Period twelve 12 months from the date of shipment by Seller Seller may provide additional years of warranty coverage beyond 12 month at the rate of 2 5 of the net sale price per year up to a total of four additional years coverage beyond the standard 12 month warranty period Seller will remedy a defect as set forth in paragraph 7 D below the Warranty The Warranty is subject to each of the following exceptions and conditions 1 Customer must promptly and in all events within the Warranty Period notify Seller of any alleged defect ina written notice the Notice which shall set forth the quantity catalog number finish original purchase order number Seller s i
24. ius Default 0000 Counts lamp hours you must reset to zero when changing lamps Lamp On Point The lamp current at which DEC detects the luminaire luminaire lamp is running Default is 1 Amp which allows for equipment fans and power supplies to run Cyclone Enclosure User Manual page 24 TEMPEST without changing the air in the enclosure Lamp on point may be set in 0 2 Amp increments between 0 2 Amps and 2 0 Amps Start up Validation When you switch power ON to the DEC3 3 controller firmware 01 00 006 and up the following indications will confirm that the major system elements are working correctly e BEEP a loud beep indicates that the processor has initialized and is functioning correctly e FANS fans run for three seconds e HEATER the heater turns on for 15 seconds This is enough to get warm to the touch DMX Connections DMX refers to USITT DMX512 a commonly used control protocol in the entertainment industry running over RS485 Consult USITT DMX installation guidelines when laying out a system or employ a qualified DMX system integrator A DMX network will be required if a The luminaire inside the enclosure requires a DMX control signal b You wish to monitor the enclosure using RDM C You wish to control the enclosure lamp relay over DMX DMX Terminations Note DMX will not normally be used in luminaire installations E E eC i Pinout 1 Ground 2 Data 3 Data 010059
25. nvoice number on which Goods were originally billed and a statement of the alleged defect along with digital photographs showing such defects where feasible 2 The Warranty shall not apply i to any claimed defect that was capable of discovery upon reasonable inspection and deemed to be waived under paragraph A above ii to any Goods that have been subject to misuse abnormal service or handling or altered or modified in design or construction iii to any Goods repaired or serviced by any person other than Seller s authorized service personnel or to Goods installed other than according to installation instructions or iv with respect to normal wear and tear 3 Seller makes no Warranty with respect to parts or components that are not the product of Seller and specifically makes no warranty whatsoever for equipment housed inside enclosure products manufactured by Seller 4 The Warranty is Seller s exclusive warranty with respect to the Goods Seller makes no warranties guarantees or representations express or implied to Customer except as set forth in this section ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR USE OR FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND DISCLAIMED C Seller will accept the return of Goods properly rejected under paragraph A above or as to which Notice of an alleged breach of Warranty has been timely given and such Goods may be
26. ot be responsible for such damage p Da a amp G Horizontal Enclosures be sure to replace the globe with the drainage hole at the lowest point after relamping Note A tapered drill bit is included with all Tornado 1900 1950 shipments Weep holes must be drilled on site as part of the installation process Cyclone Enclosure User Manual page 15 TEMPEST Installation above public Spaces If the Tornado enclosure is to be installed above an area accessible to the public eg a street or an auditorium some jurisdictions require a safety bond to be installed A stainless steel eyebolt is included with base up and horizontal versions and should be installed as follows 1 Remove one ofthe four bolts holding the Unistrut onto the enclosure base 2 Replace it with the eye bolt washer and nut supplied and screw down tight Remove this and A N bolt replace it with this NOS one Safety Bond Use a suitably rated steel wire rope threaded through the eyebolt and attach securely to a structural member in accordance with local safety regulations Cyclone Enclosure User Manual page 16 amp TEMPEST 3 Wiring and Control M All electrical work must be carried out by a properly licensed electrician in compliance with local electrical standards Failure to observe this point will void the factory warranty for the Tempest Enclosure 1 Switch off power to the branch circ
27. owing instructions provided by Vari Lite 5 Remove the Fixture tray from the enclosure as shown above Bolt the Hook Brackets to the fixture tray using the bolts provided CHECK THAT THE FIXTURE IS CENTERED ON THE FIXTURE TRAY Replace the fixture tray fixture assembly in the enclosure and bolt firmly in place Tornado Enclosure User Manual page 38 4 TEMPEST Martin MAC Ill and other tall Luminaires The MACIII is too tall to use in a Tornado 2300 with Omega Clamps installed in the usual way In this case and in similar cases the fixture must be secured in place with the omega clamp BELOW the fixture tray 1 Remove the Fixture tray from the enclosure as shown above 2 Carefully place the fixture on its side on a flat surface and identify the mounting holes in the Fixture Tray that line up with the fixture mounting locations 3 Fit the quarter turn fasteners through the Fixture Tray into the receptacles in the fixture base 4 Mountthe omega clamp into the quarter turn sockets in the fixture base through the holes provided in the fixture tray 5 Make sure that all quarter turn fasteners are fully rotated clockwise and positively locked and that the luminaire is firmly attached to the fixture tray Fixture Tray Fixture Omega Clamp 6 Replace the fixture tray fixture assembly in the enclosure and use the 5 16 bolts provided to secure firmly in place Tornado Enclosure User Manual page 39 4 TEMPE
28. p DMX Connectors 1 DMX IN from network DMX IN from outside world DMX OUTto next DMX device 2 DMX OUT to luminaire or to network if not controlling luminaire 3 DMX IN from luminaire 4 DMX OUT to network Cyclone Enclosure User Manual page 25 i amp TEMPEST Note If the enclosed equipment does not use DMX then connector 2 on the controller is DMX OUT for the enclosure DMX Line Terminations DMX cable runs must be terminated at the far end of the cable run with a termination resistor as detailed in the DMX512 standard The individual equipment installed inside the LAU UU Tempest enclosures must NOT be terminated 1 It is recommended that any line termination is done using the 3 pin terminal connector fitted DMX OUT DMXIN DMXOUT DMXIN to the DEC3 3 control circuit board LIGHT LIGHT Cyclone Enclosure User Manual page 26 4 TEMPEST Remote Device Management RDM RDM refers to ANSI E1 20 a control protocol in the entertainment industry used for device configuration and monitoring and essentially an extension of DMX512 The use of RDM is optional and uses the same RS485 cable connection as DMX512 so no additional wiring is required if DMX is already present The user must ensure that any DMX splitters or other routing devices used are RDM operable as well as DMX use Tempest strongly recommends working with a qualified RDM system integrator
29. pan Socr Sa 50 Cyclone Enclosure User Manual page 3 CERTIFICATE AND DECLARATION OF CONFORMITY FOR CE MARKING Tempest Lighting Inc 13110 Saticoy Street Unit C North Hollywood CA 91605 USA t 1 818 787 8984 1 818 982 5770 info tempestlighting com www tempest org Tempest Lighting Inc declares that their Tornado Lighting Enclosure Series 1 9xx Xxx 2 complies with the Essential Requirements of the following EU Directives Low Voltage Directive 2006 95 EC Test Report 60065 2000 13 Electromagnetic Compatibility Directive 2004 108 EC Test Report 61000 2000 15 and further conforms with the following EU Harmonized Standards EN 60065 2002 Test Report 60065 2000 13 EN 60529 2001 2002 Test Report 60529 2000 14 EN 61000 6 3 2007 A1 2011 Test Report 61000 2000 15 EN61000 6 1 2007 Test Report 61000 2000 15 EN55015 2006 A2 2009 Test Report 61000 2000 15 Dated 1 March 2013 Position of signatory President Name of Signatory Tim Burnham Signed below on behalf of Tempest Lighting Inc Cyclone Enclosure User Manual page 4 SUERTE LISTED US This is to certify that the following products Tornado 2000 US H V Lighting Enclosure Tornado 2050 US Lighting Enclosure Tornado 2000 US H V Lighting Enclosure Tornado 2200 US H V Lighting Enclosure Tornado 2300 US H V Lighting Enclosure Tornado 2400 US Lighting Enclosure Have been tested and approved
30. returned to Seller freight prepaid but only upon Customer s receipt of Seller s written return material authorization and shipping instructions The RMA shall be void if the Goods are not received within 45 days after issuance of the RMA No deduction or credit in respect of any rejected or returned Goods shall be taken until Customer has received Seller s further written deduction or credit authorization following Seller s inspection to confirm nonconformity or defect Seller will charge to Customer any and all costs incurred by Seller in connection with the handling shipping inspection and disposition of any returned Goods that are determined by Seller not to have been nonconforming upon Delivery or as to which the warranty hereunder is not applicable D UPON ANY PROPER RETURN PURSUANT TO PARAGRAPH C ABOVE WHETHER IN CONNECTION WITH A REJECTION OF GOODS OR AN ALLEGED BREACH OF WARRANTY AND BASED UPON THE CONDITIONS SET FORTH IN THIS PARAGRAPH 7 SELLER AGREES THAT IT WILL AS THE SOLE AND EXCLUSIVE REMEDY UNDER THE CONTRACT OR OTHERWISE FOR ANY NONCONFORMITY OR BREACH OF WARRANTY AND AT SELLER S SOLE ELECTION i REPAIR SUCH GOODS OR ii REPLACE SUCH GOODS Tornado Enclosure User Manual page 49 11 Step 1 Step 2 amp 4 TEMPEST Tempest Product Support First contact your local Dealer for support Your dealer is best placed to respond quickly to your needs If your dealer is unable to answer your questions pleas
31. s 96 Response Curve 1 default DMX level 0 25 Relay disabled open DMX level 26 75 No change to relay status DMX level 76 100 Relay enabled normally closed Response Curve 2 DMX level 0 19 No change to relay status DMX level 20 40 Relay disabled open DMX level 41 59 No change to relay status DMX level 60 80 Relay enabled normally closed DMX level 81 100 No change to relay status Tornado Enclosure User Manual page 30 amp 4 TEMPEST SET DMX RESPONSE DMX Response sets a delay time before DMX Control Mode settings are acted on Setting a response delay of a few seconds would prevent unintended fixture relay state changes in the event of a short accidental change in DMX level NOTE from firmware revision 0 00 100 DEC holds last valid DMX level if DMX is interrupted Response Delay Values are No Delay default 1 2 5 10 15 20 30 60 seconds SET TEMP UNITS Choose to display temperature values in Celsius or Fahrenheit default Celsius Note that temperature settings must be entered in Celsius SET TEMP RANGES Set three temperature trigger points for Bottom Top and Trip temperatures in C SET TEMP LOWER minimum temperature to be maintained default O C permissible range 0 10 C SET TEMP UPPER maximum desired temperature default 40 C permissible range 35 50 C SET TEMP TRIP temperature at which load will be isolated see note default 60 permissible range 55 70 Note A thermal emergency is wh
32. s displayed will depend on the RDM interface used These screen shots were taken running the GetSet program in Windows 7 and connecting to a DEC3 3 controller using a RDM TRI MKT interface Tempest part 2000 190 1 Device discovered in o Remote Device Tempest Lighting Inc DECS MK 2 Controller Software Version 00 12 Root and Sub Devices Root Device DEC3 2 Test Unit Click on Item to Activate Parameter Key Required Parameter Show Supported Parameter Manufacturer Parameter ESTA Reserved Parameter Supported Parameters Parameter QUEUED MESSAGE STATUS MESSAGES STATUS ID DESCRIPTION CLEAR STATUS ID PARAMETER DESCRIPTION DEVICE MODEL DESCRIPTION MANUFACTURER LABEL DEVICE LABEL DMx PERSONALITY DMx PERSONALITY DESCRIPTION DMx START ADDRESS SLOT INFO SLOT DESCRIPTION DEFAULT SLOT VALUE nm Tornado Enclosure User Manual page 32 File Connection Options Tools Help 1 Device discovered in 0 3 seconds File Connection Options Tools 1 Device discovered in 0 3 secon Tornado Enclosure User Manual Help 10 0 90 0 49 6 50 4 3 T Sensor Relative Humidity 40 0 100 Humidity Normal Range r Delta Range Min Max Min Max Firmware Upload This view shows a single DEC3 2 test unit that has been correctly discovered and labeled by the GetSet software suite
33. to standards UL 508 electrical and UL 50 environmental as NEMA 3R enclosures for use in the United States and Canada This declaration is made by the manufacturer Tempest Lighting Inc 13110 Saticoy Street Unit C North Hollywood CA 91605 USA This declaration is based on tests that were conducted on the submitted samples of the above mentioned products Listing Report No 3198609LAX 001a refers Dated December 17th 2010 Signature UAM Mal Dl Tempest Lighting Inc Tempest Lighting Inc 13110 Saticoy Street North Hollywood CA 91605 USA www tempest org info tempestlighting com t 1 818 787 8984 f 1 818 982 5582 Cyclone Enclosure User Manual page 5 TEMPEST J Re 1 Introduction Using This Manual Please read this manual in its entirety before starting work All the information contained is important and should be read carefully before proceeding Heed all warnings and advisories Terminology Enclosure Tornado Lighting Enclosure Luminaire intelligent lighting fixture that will be placed into the enclosure DMX ANSI E1 11 2008 Entertainment Technology USITT DMX512 A Asynchronous Serial Digital Data Transmission Standard for Controlling Lighting Equipment and Accessories RDM ANSI E1 20 2006 Entertainment Technology RDM Remote Device Management over DMX512 Networks Icon Key Q Valuable information Electrical Warning Safety Information IMPORTANT SAFETY NO
34. ual page 12 TEMPEST i b Mounting plate Guidelines Use 6mm or greater galvanized steel or stainless steel plate Do not obstruct wiring access Tornado 2000 2200 2300 Mounting Hole Pattern Wiring Access opening 5 x 5 125 x 125mm 254mm Mounting holes 12 5 9 16 13mm 317 5mm Tornado 2400 Mounting Hole Pattern n CD 7 E E E E a E CD Y m E 12 25 311 15 00 381mm i Cyclone Enclosure User Manual page 13 TEMPEST Orientation Guidelines m Tornado 1900 xx e Tornado 1950 xx d LJ J Tornado 2000 Tornado 2100 Tornado 2200 Tornado 2300 Tornado 2000 xxH Tornado 2100 xxH Tornado 2200 xxH Tornado 2300 xxH Tornado 2400 xx Cyclone Enclosure User Manual page 14 Tornado 2000 xxV Tornado 2100 xxV Tornado 2200 xxV Tornado 2300 xxV amp TEMPEST Drainage For base up globe down or horizontal operation a small drainage hole will be drilled in the globe to permit any water draining through the enclosure to exit harmlessly This will normally be done at the factory but if done on site YOU MUST USE THE APPROPRIATE TAPERED DRILL BIT OBTAINABLE FREE OF CHARGE FROM TEMPEST LIGHTING A standard drill bit may crack the plexiglass globe Tempest Lighting will n
35. uit carefully following lockout and tag out procedures Failure to do so could cause serious injury or death 2 You will need two electrical junction boxes located within a short distance from the enclosure one for power one for DMX control Use outdoor rated flexible conduit between the box and the enclosure 3 AC and control circuits must be wired in separate conduits 1 20VAC or 208VAC or 230VAC Z poe o I I I I I AC DMX Lighting Power Control Control I Flexible Conduit Conduit entry holes d ui AC Power DMX Control ya 22 2mm The conduit entry holes accept US 77 conduit fittings and international 20 22mm OD conduit fittings Power and DMX conduit entries For temporary installations use a suitable cable and clamp in the same openings Cyclone Enclosure User Manual page 17 i amp TEMPEST One or Two Power Circuits Single Feed Split Feed Tempest enclosures may be wired on single or double line supplies On a single feed both enclosure and luminaire are permanently on With a double line supply you can switch off the luminaire when not in use while the enclosure continues to protect it 24 7 Single Feed e Enclosure and luminaire are permanently on e Enclosure and Luminaire must be rated for the same voltage e Supply must be rated for luminaire current
36. use Service mode for normal operation Cyclone Enclosure User Manual page 23 TEMPEST J u DEC3 3 Control Parameters Temperature and Humidity Ranges Max Humidity DMX Address Cooling Fan s Emm 55 70 Default 60 Low Upper Temp 35 50 C Default 40 C Relative Humidity Trend Temp 50 9096 Dynamic Default 8096 IdealTemp Dynamic based on Relative Humidity High LowerTemp 0 10 C Default O Heater s Notes 1 In moving light enclosures the temperature sensor is located in the exhaust airflow Temperatures shown may be higher than those around the luminaire 2 We recommend using the factory default settings for several weeks or months before making any changes In most cases they will not be necessary Range 50 90 Default 80 The threshold at which air inside the enclosure is heated to raise dewpoint and prevent condensation Setting a higher Max Humidity is not a bad thing in high humidity climates Setting the Max Humidity too low will result in unnecessary heating and excessive energy use So set the Max Humidity at the top end of the relative humidity likely to be experienced on site Range 001 510 Default 001 Sets the DMX address for the lamp relay control See also DMX Response Set Temp Units Display Degrees Celsius or Fahrenheit Default Celsius Lamp Hours Note that temperature settings must always be Cels
37. when designing an RDM network Go to www tempest org for contact information RDM and RDM Integration DEC3 3 s RDM implementation allows system integrators to remotely configure control or monitor DEC3 3 attributes including e Relative Humidity DMX RDM e Air Temperature e PCB Temperature e Lamp Current l RDM is an effective and powerful e Elapsed Lamp Hours tool for commissioning and e Lamp Relay Status monitoring an installation particularly in large systems For e Fan Relay Status further guidance please consult a Heater Relay Status qualified RDM system integrator e DMX Status Tempest Lighting warrants DEC3 3 to be compliant with the RDM standard but is not an e DMX Start Address e DMX Personality RDM Mode systems integrator and can offer e Device Type only basic guidance on e Device Label utilization e Software Version Cyclone Enclosure User Manual page 27 Control Interface LED Indicators Heater Fan Lamp On Lamp Relay Temp DMX ON Green Ea ON Green E us ON Green OFF ON Green ON Red FLASHING Green EHEHEHE ON Green ON Amber ON Red FLASHING Red 888888 8 OFF ON GREEN pss E CARNE ON RED Li Tornado Enclosure User Manual amp 4 TEMPEST CD a gt LL im P Heater is ON to maintain lower temperature level or to prevent condensation Lamp is ON or Temp
Download Pdf Manuals
Related Search