Home

CN2610 Dual-LAN Async Server User`s Manual

1. S e r v e r s e iS t i n g 4 In addition you only need to remember to e Use the SEL button to move up one level i e left to right on the tree graph e Use the MENU button to move down one level i e right to left on the tree graph e Use the cursor keys A and V to scroll between the various options within a level i e up and down on the tree graph As you use the buttons to operate the LCM display you will notice that with very few exceptions moving up one level causes the bottom line of the display to move to the top line of the display You will also notice that the bottom three options in level 2 and all of the options in level 3 have either a C or D attached The meaning is as follows e C configurable I e you are allowed to change the setting of this option e D display only I e the setting for this option is displayed but it cannot be changed this does NOT necessarily mean that the number doesn t change only that you can t change it Main Menu Server Serial number setting Server name Firmware ver Model name Network Ethernet status setting MAC address IP config IP address Netmask Gateway DNS server 1 DNS server 2 Serial set Select port Baudrate Data bit Stop bit Parity Flow control Tx Rx fifo Interface Tx Rx bytes Line status BSeaaAaAgaAaAgaAagQaQaaaaanagyssays The part of the LCM operation th
2. This is where e CN2610 16 is the CN2610 s name e 03 is the CN2610 s serial number e 192 168 127 254 is the CN2610 s IP address There are four push buttons on the CN2610 s nameplate Going from left to right the buttons are Button Name Action MENU menu activates the main menu or returns to an upper level A up cursor scrolls up through a list of items shown on the LCM panel s 2nd line V down cursor scrolls down through a list of items shown on the LCM panel s 2nd line SEL select selects the option listed on the LCM panel s 2nd line The buttons are manipulated in a manner similar to the way a modern cellular phone operates As you move through the various functions and setting options note that the top line shows the current menu or submenu name and the bottom line shows the submenu name or menu item which is activated by pressing the SEL button Detailed Menu Options The best way to explain all of the CN2610 s LCM functions is to refer to the tree graph shown on the next page There are three main levels 1 2 and 3 with each level represented by a separate column The first thing to remember is that the MENU button is used to move back and forth between the LCM panel s default screen and main menu screen CN2610 User s Manual Service Information M a i n M e n
3. NT NT Terminal Binary or TERM_BIN mode supports automatic link to Ethernet hosts for Terminal or Telnet users by redirecting Telnet requests to the specified Ethernet host Below we describe how to set auto link host and login ID information Auto linking one TERM_BIN port to a port in RTELNET mode provides a transparent link through the network 9 Move the cursor to the Description more setting column and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real COM gt Server Proprietary Protocol 02 Real COM j gt Server Proprietary Protocol 03 Real COM gt Server Proprietary Protocol 04 Real COM gt Server Proprietary Protocol Real COM f gt Server Proprietary Protocol Multiplex TERM_BIN NT Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol 10 The pop up selector contains input display fields for Quit key Auto link protocol Link by input IP Auto login prompt Terminal type Inactivity time Authentication type and TCP alive check time Each item is described in detail below the figure Quit key yNbl cokes mel amy ob aol eeleron Telnet TCP port Primary Host LP lank by input TP Secondary host IP Auto login prompt Password prompt Login user name Login password Terminal type Inactivity tim
4. Status Idle Modet CN261016 IP Address 192 168 34 219 192 168 36 219 MAC Address 00 90 E8 10 B1 67 00 90 E8 10 B1 68 Redundant COM 2 Redundant COM 3 Redundant COM 4 Redundant COM 5 Redundant COM lundant COM 7 jundant COM LANI LAN2 8 tedundant COM LANT LAN2 9 jundant COM LANI LAN2 10 Redundant COM LAN1 LAN2 11 Redundant COM LANI LAN2 12 lundant COM LANI LAN2 13 lundant COM LANI LAN2 14 Redundant COM LANI LAN2 15 Redundant COM LANI LAN2 16 Redundant COM LAN1 LAN2 5 The status will show On line which means that all of the port numbers with LAN 1 and LAN 2 IP address will appear on the page If your maximum connections is 2 the monitor s connection 2 will show the LAN IP address EB NPort Monitor Utility lajxj Function Run Help i 2 b Exit Search Start Stop Ef Server List 19 Status On Line Model CN2610 16 IP Address 192 168 34 219 192 168 36 219 MAC Address 00 90 E8 10 B1 67 00 90 8 10 B1 68 Connections Por OperationMode LAN Connection Connection2__ 1 Redundant COM 192 188 34 207 192 168 386 207 Redundant COM 192 168 34 207 192 188 38 207 Redundant COM 192168 34 207 132 168 386 207 Redundant COM 132 168 34 207 192 168 36 207 Redundant COM 192 188 34 207 192 188 36 207 Redundant COM 192 188 34 207 192 168 36 207 Redundant COM 192 168 34 207 a 192 188 36
5. 5 On the Password page add a password or change the existing password Check the Remember Password checkbox to remember the password on this computer Property Sheet x Basic Configuration Password Access Control Current Password New Password Confirm Password J Remember Password 4 35 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 6 The Access Control page allows you to set up access rights for each of the CN2610 s ports Access right is assigned by IP address In the example shown here the netmask of 255 255 255 255 limits access to the listed IP address 192 168 6 16 To allow access to a group of IP addresses adjust the netmask accordingly To allow any IP address to access a port delete all IP addresses assigned to that port Click Modify to make changes IP Address ha 7 And then click OK to return to the Access Control page IP Address M Add Access Grant IP a 192 168 127 100 ara pK Cancel 4 36 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 8 Click OK to return to the Configuration page Property Sheet MOXA Async Server CN2510 8 Properties 4 37 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 10 Check the box es next to the port s you would like to modify and then click Modify Sett
6. Add Remove Hardware Wizard Select a Device Driver Which driver do you want to install for this device MOXA Async Server CN2504 MOXA Async Server CN2508 MOXA Asyne Server MOXA Async Server CN2610 16 MOXA Asune Server CNZRIN A 11 The Wizard will start installing the Server driver and automatically search the network for copies of the CN2610 model you selected in the previous step Add Remove Hardware Wizard Start Hardware Installation Windows is ready to install drivers for your new hardware 4 29 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 12 Although the next window to open states that the software hasn t passed Windows Logo testing you can rest assured that this driver has already been tested and been shown that it can support this Windows OS Click Continue Anyway to proceed Digital Signature Not Found Add Remove Hardware Wizard Hardware Install Windows is installing drivers for your new hardware Configuration 4 30 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 13 You can select the CN2610 that was located automatically or select Manually Enter the IP address of CN2610 Server Async Server and then enter the IP address of a different server Click Next to finish installing the CN2610 driver MOXA NPort Server Installation Select the NPort Server 7 Async Server you want to install Which the NPort Server A
7. Details Components Ha Management and Monitoring Tools x l Networking S a5 Other Network File and Print Services DOMB _J LI A Remote Installation Services 2 0 MB amp amp Remate Storane RAMA xi Description Contains a variety of specialized network related services and protocols Total disk space required 17 2 MB F ER E Ek 1914 9 MB 2a ee E 3 Select Details and then Internet Authentication Service Click OK to continue until the installation is finished Networking Services x To add of remove a component click the check box 4 shaded box means that only part of the component will be installed To see what s included in a component click Details Subcomponents of Networking Services B Domain Name System DNS amp Dynamic Host Configuration Protocol DHCP 0 0 MB amp Intemet Authentication Serv 0 0 MB RPC over HTTP Proxy 0 0 MB simple TCP IP Services 0 0 MB Si windows Internet Name Service WINS 0 9 MB l Description Enables authentication authorization and accounting of dial up and YPN users IAS supports the RADIUS protocol Total disk space required 14 6 MB Details Cancel Space available on disk 1914 9 MB CN2610 User s Manual RADIUS Server 4 After the installation is finished click Administrative Tools and run Internet Authentication Service The window shown below will open Internet Authentication
8. Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real COM Async Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Real COM Async Server Proprietary Protocol 04 Real COM Async Server Proprietary Protocol OS Real COM Async Server Proprietary Protocol 06 Device Control Async Server Proprietary Protocol 07 Real COM Async Server Proprietary Protocol 5 4 CN2610 User s Manual Setting Up Device Control 2 Use the arrow keys to highlight ASPP and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 DE Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM t rver Proprietary Protocol 05 NT Real COM Proprietary Protocol 06 Device CONECTO lrver Proprietary Protocol 07 NT Real COM t rver Proprietary Protocol NT Real COM Async Server Proprietary Protocol 3 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application Description more setting 01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Pr
9. Export via Host name IP address File name User name Press CAML ier Siceliat ooo Import Saved settings can be imported back to the CN2610 There are two settings to choose from for importing from a file Console Terminal or Remote RCP Console Terminal Import 1 Run Start gt Programs gt PComm Terminal Emulator Follow the steps given earlier to enter the MAIN MENU 2 From the MAIN MENU select seTting and then press Enter E3 PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit PortManager Window Help 4 BIA ellas 328 E COM1 115200 None 8 1 T100 CN2510 8_5631 V2 0 Port B2525t save Utility Restart Exit 16 35 CN2610 User s Manual Administrative Utilities 3 From the SETTING MENU select Import and then press Enter PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a BIA elhal s2 iol xi CN2510 8_5631 V2 0 SETTING MENUBES Export Esna Default Quit Import configuration from previously saved file ous menu Profile Edit Port Manager Window Help a BIA elles S2 Export Esna Default Quit Import configuration from previously saved file back to menu Enter Import via using XMODEM f Host name IP address File name User name Press CTRL U to start 16 36 CN2610 User s Manual Administrative Utilities 3 When you see Start loadi
10. 3 The CN2610 s MAIN MENU will open as shown below E Telnet 192 168 127 254 CNA LOSE LE V20 Server SEZI Aae AE Oh ons nl a A C a OD Go Examine modify async server node table configuration Enter select ESC previous menu 2 6 CN2610 User s Manual Getting Started Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Shortcut Key Capitalized letter of the word Esc Key Accessing the Console from a Console Terminal If you do not know the CN2610 s IP address or it is not possible to use Telnet you can use a direct console connection to enter the CN2610 console Use a terminal emulation program for the console PC such as HyperTerminal or MOXA PComm Terminal Emulator 1 If you are using Windows 9x ME NT run PComm26 exe from the Win9xNT directory If you are using Windows 2000 XP 2003 run PComm2K exe as shown in the figure below from the Win2kXP2003directory Ep ASPP O didas 3 5 driver 4 DB Linux O SCOOpenSeverd k SYR4 2 E RELEASE UnixWare SETUP 3 Utility 2 7 CN2610 User s Manual Getting Started 2 Click Next to Continue i PComm Lite 2000 XP er 1 2 Welcome to the PComm Lite 2000 XP Ver 1 2 Setup Wizard 3 Select the I Agree option
11. Async Server Proprietary Protocol 04 Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol i INT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application t ption more setting 01 Real COM Server Proprietary Protocol 02 Real COM Dialin out Server Proprietary Protocol 03 Real COM Terminal Server Proprietary Protocol 04 Real COM Reverse Terminal Server Proprietary Protocol 05 Real COM Server Proprietary Protocol 06 Real COM Multiplex Server Proprietary Protocol 07 Real COM Printer Server Proprietary Protocol 08 Real COM Mop ts tate sit Server Proprietary Protocol NT Real COM Raw UDP Redundant COM 5 3 CN2610 User s Manual Setting Up Device Control 5 ASPP mode is selected by default C2 6 0 enoe ROO O OOOO Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting om 02 03 Real COM 04 NT NT Real COM NT Real COM NT NT Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol 05 06 07 Real COM Device Co
12. Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real COM Async Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Real COM Async Server Proprietary Protocol 04 Real COM Async Server Proprietary Protocol 05 Real COM Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol CNAE TO E MS W250 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter Pork Application t ption more setting 01 NT Real COM 02 NT Real COM Dialin out 03 NT Real COM Terminal 04 NT Real COM Reverse Terminal 05 NT Real COM Device Control Server Proprietary Protocol NT NT NT 06 Real COM Multiplex Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol 07 Real COM Printer Server Proprietary Protocol 08 Real COM Mali Host ray Server Proprietary Protocol NT Real COM Raw UDP Redundant COM 14 4 CN2610 User s Manual Setting Up Multiplexor 5 The Multiplex application supports two operation modes RTELNET and TERM BIN RTELNET mode is selected by default For the Host CN2610 use RTELNET mode CMA eG Se 19
13. None 02 TI5200 i None s yes None 03 125200 J None yes None 04 LI S200 dl None s yes None okel 115200 J None s yes None 06 TI5200 1 None f yes None 07 aio WA0 0 al None yes None 08 15200 ale None f yes None Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 1 1 5 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection CN2610 User s Manual Setting Up Raw UDP 4 Press ESC to return to the PORT MENU Save 1 When exiting the SERVER MENU you will be prompted to save settings Press Y to save CN2610 8_19 V2 0 Eondon Teo Ce A Or oE O o USer table Examine modify async server basic configuration Enter select ESC previous menu Warning You had modified the configuration without saving Would you save it now 2 You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel Che oO 0 Server Port seTting UEM Ey Restart 2x1 Save current configuration to Flash ROM ESC back to menu Enter s
14. 10 9 CN2610 User s Manual Setting Up Terminal 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item is described in detail below the figure CN2610 8 Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed Parity FIFO RIS CTS XON XOFF Disco orl top Oh 15200 1 None yes None 02 C1152090 i None f yes None 03 Paka AO iL None s yes None 04 PLS 2 0103 alae None i yes None ala 115200 Laii None amp yes None 06 ELS ZOO aari None i yes None 07 CLS 2001 i 4 None yes None 08 115200 itl None f yes None Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 1 1 5 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection 4 Press ESC to return to the PORT MENU Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save GNAGIO s 1S wAsEO ip obo peunit t
15. 4 45 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 5 The Access Control page allows you to set up access rights for each of the CN2610 s ports Access right is assigned by IP address Server Properties Addo BEnIGYE piod aalr akeeh o cms The Transmission page lets you to select a Transmission Mode and Tx FIFO for each port Server Properties Ice Enable Hi Performance Enable Hi Performance Enable Hi Performance Enable Hi Performance Enable Hi Performance Enable Hi Performance Enable Hi Performance Enable oy OO amp wee 4 46 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 7 The Access Control page is used to modify access rights to the server Server Properties Silia Adalat 8 The Advanced page allows you to add routes to the CN2610 However since the CN2610 has a column to set the Default Gateway you can ignore this configuration Server Properties Modit x Cancel 4 47 5 Setting Up Device Control Device Control applications use standard Linux Unix Socket programming for Linux Unix systems or WinSock programming for Windows systems to control device data transmission directly With the CN2610 configured for RAW mode you can focus on pure data transmission without using serial port control or serial modem control signals You can also use ASPP mode provided e
16. CTS GND 3 7 GND Toa gt 3 RxD RxD 5 lt 2 TxD DCD 6 lt 8 DCD CTS 7 4 RTS DTR 8 gt 6 DSR CN2610 User s Manual Pin Assignments and Cable Wiring 8 pin RJ45 to Male DB25 for the CN2610 RJ45 Port RJ45 Connector Male DB25 Female DB25 Ti RS 232 ENZI L Device 8 pins Cable Wiring 25 pins DSR 1 6 DTR RTS 2 4 CTS GND 3 7 GND TxD 4 gt 2 RxD RxD 5 lt 3 TxD DCD 6 lt _____ 8 DCD CTS 7 5 RTS DTR 8 gt 20 DSR DB9 and DB25 Connector Pin Assignments DB9 Connector Pin Assignment Male DB9 Connector Female DB9 Connector O DSR in ea pee tin 6 DTR out Hite out 3 TxD out TxD in 3 7 CTS in GTS Un 4 DTR out DSR in 4 8 RTS oul 5 GND GND5 ge O DB25 Connector Pin Assignment Male DB25 Connector Female DB25 Connector O i RxD in 2 14 TxD out 3 CTS in 4 RTS out 5 DTR out 6 BED iM 5 20 DSR in 13 25 O E LCM Display For first time installation we recommend using the LCM display and four push buttons to configure the IP address Basic Operation If the CN2610 is working properly the LCM panel will display a green color The red Ready LED will also light up indicating that the CN2610 is receiving power After the red Ready LED turns to green you will see a display similar to C N 2 6 1 0 1 6 0 3 1 9 2 1 6 8 1 2 7 2 5 4
17. ONOaRWND Async RS 232 Port Pin Assignment Pin RS 232 1 DSR in LETTET 2 RTS out 1 8 3 GND 4 TxD out L I 5 RxD in 6 DCD in 7 CTS in 8 DTR out Cable Wiring 10 100BaseTX Port Cable Wiring Straight Through Cable Cross Over Cable RJ45 Plug Pin 1 RJ45 Plug Pin 1 Cable Wiring Cable Wiring 3 3 3 1 6 6 6 2 1 1 1 3 2 2 2 6 D 2 CN2610 User s Manual Pin Assignments and Cable Wiring Async RS 232 Port Cable Wiring 8 pin RJ45 to Male DB9 for the CN2610 RJ45 Port RJ45 Connector Male DB9 Female DB9 E 7A RS 232 8 pins Cable Wiring 9 pins DSR 1 6 DTR RTS 2 gt 7 i CTS GND 3 5 GND TxD 4 gt 3 RxD RxD 5 lt 2 TxD DCD 6 lt _____ 1 pcp Gis 7 lt 8 ATS DTR 8 gt 4 DSR 8 pin RJ45 to Female DB9 for the CN2610 RJ45 Port RU45 Connector Female DB9 Male DB9 RS 232 CN2610 i gi Device 8 pins Cable Wiring 9 pins DSR 1 4 DTR RTS 2 gt 8 CTS GND 3 5 GND TxD 4 gt 2 RxD RxD 5 lt ______ 3 TxD DCD 6 1 DCD CTS 7 7 RTS DTR 8 gt 6 DSR 8 pin RJ45 to Female DB25 for the CN2610 RJ45 Port RJ45 Connector Female DB25 Male DB25 E RS 232 CN2610 Ti Device 8 pins i Cable Wiring i 25 pins DSR 1 20 DTR RTS 2 gt 5
18. T100 Profile Edit Port Manager Window Help Open Ctrl Alt o Close Ctrl Alt L Close All Ctrl Alt A Port Enable Gtr Alt E Fort Disable Ctrl Alt Q Properties Clear Screen using XMODEM end Pattern Send Break Capture Double Byte Character Press CTRL U to start Start loading file le StateOPEN Ma m File transfer In the File Transfer window select XModem CheckSum for Protocol and Transmit for Direction and then click OK The file will be transmitted to the CN2610 File Transfer l m Protocol Direction C ASCII CE Transmit Kermit C Receive XModem 1KCRC XModem CRC Modem Cancel C ZModem 16 13 CN2610 User s Manual Administrative Utilities 7 Locate the upgrade file CN2610_2 ROM for example and then click Open to transfer the firmware to the CN2610 Look in 22 3 5 Floppy 4 ex FE CN2510_2 0 ROM File name JCN251 0 20 Files of type E X Cancel 8 The CN2610 will store the new firmware in its Flash ROM and then restart the entire system completing the Firmware Upgrade procedure Transmit File Protocol KModem CheckSum Port Com File Name MXPCI SYS File Size 0 Transmit Length D Remote RCP Upgrade NOTE NOTE RCP Remote Copy Program is the Unix utility for copying files over the Ethernet RCP allows transparent copy
19. TOU N2608 19 V20 ON TOR MENU EE Line Network Async async Setting Routing PPP Trace Quit Monitor asynchronous port connective utilization Enter select ESC previous menu Line 1 From the MONITOR MENU select Line and then press Enter CN261 0 319 eee Network Async async Setting Routing PPP Trace Quit Monitor asynchronous port connective utilization Enter select ESC previous menu 2 The Line page shows the status of each port Line Network Async async Setting Routing PPP Trace Quit Monitor asynchronous port connective utilization ESC back to menu Enter select Type Idle Status BBR 39Sec negotiation TERM_BIN 39Sec select protocol RTELNET 39Sec listen ASPP 39Sec listen TERM_BIN 39Sec select protocol RAW PRN 39Sec listen FIXTTY 39Sec Sl listen S2 listen ASPP 39Sec listen RAW UDP 39Sec data transfer Type The current operation mode of the port set in PORT MENU gt Mode Idle The amount of time the port has been idle Status The current status of the port If a host is connected to this port then the host s IP address is displayed in this column 3 Press Esc to return to Line 16 3 CN2610 User s Manual Administrative Utilities Network 1 From the MONITOR MENU select Network and then press Enter 2610 8 CN2610 8_19 V2 0 Line Network Async async Setting Routing PPP Trace Monitor Network protocol status ESC back to menu Enter select Received Received RDisca
20. s Manual Setting Up Printer Selecting the Application Open Port Menu gt Mode to set up the Printer application 1 From the MAIN MENU select Port and then press Enter Server sAve Utility Restart Exit Examine modify async server ports configuration seTting Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports select Enter ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application 01 Real COM Description more setting Async Server Proprietary 02 Real COM Async Server Proprietary 03 Real COM Async Server Proprietary Protocol 04 Real COM Async Server Proprietary irene royero b PYOCOC L PrOt OCOL Protocol Protocol Protocol Real COM Async Server Proprietary INT Real COM Async Server Proprietary NT Real COM Async Server Proprietary Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application ption
21. set printer name usr lib lpadmin Redirect the printer spooler to write to pLaser1 v dev iop1 pipe iop1 Assumes the printer name is Laser1 add one line to etc printcap file Laser lp dev iop1 sd ust spool Laser 1 make spool directory mkdir usr spool Laser1 1 execute asprint for Group 01 asprint dev iop1 CN2610 IP address 2048 amp Start asprint utility to read from pipe iop1 and write to the CN2610 printer port dev iop1 the device name the spooler is writing to CN2610 the host name of the CN2610 as defined in etc hosts or its IP address 2048 the TCP port number Group01 of the printer port on the CN2610 accept printer Laser lpr PLaser1 file_name txt Set Laser to accept print request Repeat Repeat the above steps to set up another printer For printers in the same group it is not necessary to repeat every step 13 12 CN2610 User s Manual Setting Up Printer Setting up Windows Hosts Windows uses the LPD LPR application to access printers MOXA provides LPD PRN mode for serial printing In this section we explain how to install a LPD LPR printer in a Windows NT 2000 environment to access a serial printer connected to a CN2610 Setting up a Windows NT Host 1 First you need to add TCP IP printing service to your Windows NT 2 Go to Start gt Settings gt Control Panel gt Network
22. ANN C Internet connection server Enable all of the computers on this network to connect to the Internet Remote access server Enable remote computers to dial in to this network C Virtual private network VPN server Enable remote computers to connect to this network through the Internet Network router Enable this network to communicate with other networks C Manually configured server Start the server with default settings lt Back Cancel start aAe s E Routing and Remote A 115pm 4 Select Set up an advanced remote access server and then click Next to continue Routing and Remote Access iol x Action 12 eS eed ee a T A Routing and Remote Access Server Setup Wizard Tree Remote Access Server Setup Routing You can use a basic configuration or more advanced options to set up this remote gg Serv access server ANN Select a configuration type based on the complexity of your network C Set up a basic remote access server Select this option to create a standalone server that will have simplified administrative control Set up an advanced remote access server Select this option to create a server that will have advanced administrative features such as remote access policies or if you plan to add this server to a domain lt Back Cancel Astarte 4 routing and Remote A te 1 56PM B 13 CN2610 User s Manual RADIUS Server 5 Sel
23. COM30 wy MOXA Communication Port 5 COM31 F MOXA Communication Port 6 COM32 MOXA Communication Port 7 COM33 MOXA Communication Port 8 COM34 oy Printer Port LPT1 i Sound video and game controllers m System devices 4 32 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Configuring the CN2610 in a Windows 2000 Environment After the CN2610 driver is installed you will be given the option to proceed directly with the configuration of the CN2610 You may also configure the CN2610 at a later time In this section we explain how to configure Real COM Mapping 1 Click Device Manager gt Multiport serial adapters right click the CN2610 you would like to configure and select Properties i0ix Action view gt a nEle ala Sy Floppy disk controllers 9 Floppy disk drives IDE ATA ATAPI controllers T Keyboards TA Mice and other pointing devices m Monitors J Multi port serial adapters 1 E Network Disable F Ports C Uninstall 0 4 Com Com Scan For hardware changes oy Mox F MOXA Communication Port 3 COM29 F MOXA Communication Port 4 COM30 E MOXA Communication Port 5 COM31 i MOXA Communication Port 6 COM32 i MOXA Communication Port 7 COM33 F MOXA Communication Port 8 COM34 aF Pri
24. Click the Services tab and then select Add Idertification Services Protocols Adapters Bindings Network Services E Microtolt DHCP Server W NetBIOS Intestace E Network Monitor Toots and Agent M Remote Access Service 3 Select Microsoft TCP IP Printing and then click OK to continue Select Network Service _ Chick the Netwotk Service that pou want to retal fen chek OK II ES you have an instalation dek for thee component chek Have Disk Network Serios E NetBIOS Irtedace E Neswork Monitor Agent E Netwotk Monitor Tools and Agent E Remote Access Service La iE r Cnr den 4 Insert the Windows NT installation CD to your computer s CD driver 13 13 CN2610 User s Manual Setting Up Printer 5 After the Microsoft TCP IP Printing service is added reboot your computer 6 At this point you can start configuring your LPR LPD Printer 7 Click Start gt Settings gt Printers TON t you pba rndiod ecb ae Mpira AN settings wil be managed and conligwed on this computer C Network peinter server Connect to 6 on another machine All settings tor plepphliraing seman api sove that has boen set 13 14 CN2610 User s Manual Setting Up Printer 10 In the window that opens next click Add Port 12 Enter the CN2610 s IP Address and then enter the Print Queue s name Click OK to continue Add LPR compatible printer 192 1
25. Console Password Ok ha J Down K Up Q Quit Enter Select ha ee IP address gt CN2610 IP Name gt CN2610 server name Console Password gt CN2610 console password 3 Save and exit Basic Extended Permission Group Setting Basic and extended permission group defines access rights for users Add Modify permission group Configuration gt User Permission Administration gt Basic Permission Maintenance or Extended Permission Maintenance Basic Configuration gt ser Permission Maintenance Proxy Server Administration CN2610 User s Manual RADIUS Server Modify User Permission gt asic Permission Maintenance Extended Permission Maintenance Save amp Exit gt dd Permission Group Modify Permission Group Delete Permission Group 4 5 4 5 Add Basic Permission 4 Group Name Examplel Maximum occurrences user punk Maximum minutes login 60 Idle minutes force to logout 25 Maximum login hours month 500 gt k 4 5 Basic Permission Group Example Description Group Name Example Name of this permission setting Maximum occurrences user 1 The user can only login onc
26. ESC back to menu Enter select Host name Host IP address Server Configuration Route_table 1 From the MAIN MENU use the arrow keys to select Server and then press Enter CN2610 8_19 V2 0 Server Royal enoe S N Oh oil A E a E Examine modify async server node table configuration Enter select ESC previous menu 2 From the SERVER MENU select Route_table and then press Enter CNOGIO gt E WS VZN ibehmorunlt t ole A Oa o ROUte table MRUi pqmer lolk memOlbnme Examine modify async server basic configuration Enter select ESC previous menu 2 18 CN2610 User s Manual Getting Started 3 The Route_table specifies routing parameters The Route_table page contains input display fields for Entry Gateway Destination Netmask and Metric Each item is described in detail below CNZ EDD Ble V20 ngopo an it s ome O a es Oa o ROUte table RARES an o EO Examine modify the routing table ESC back to menu Enter select Gateway Destination Netmask Gateway The gateway IP address or interface source IP address to which data packets are sent Destination The IP address of a host or network to which the route connects Netmask The netmask of the destination network Metric The number of hops from source to destination Refer to Chapter 14 for routing settings Server Configuration User_table 1 From the MAIN MENU use the arrow keys to select Se
27. From the SERVER MENU select Adv and then press Enter a 2 SERVER MENU Lan Adv Host_table Route_table User_table Examine modify async server advance configuration Enter select ESC previous menu 15 3 CN2610 User s Manual Setting Up Routing 3 Use the Up Down arrow keys to move the cursor to the Routing protocol pop up selector Press Enter to see the options Select RIP 1 or RIP 2 The RIP setting is only for sending packets For receiving packets the CN2610 supports both RIP 1 and RIP 2 ONZ 6G Ses N9 0 Lan Adv Host_table Route_table User_table Quit Examine modify async server advance configuration ESC back to menu Enter select RADIUS T SSrvEr IE RADIUS key UDS pece lt La Aa ike Ze Enable RADIUS accounting SNMP community name SNMP trap server IP address Ethernet IP forwarding ROUCITNORP LOCOCO TCP retransmission timeout S50 SOOO ED SIO data transfer timeout Garb ole 0 0 L00 e 4 Press Esc to return to the MAIN MENU Configuring the Static Routing Table Although RIP 1 and RIP 2 periodically update routing tables between different routers you still need to add routing entries in the routing table for routes only directed to you Open Server Menu gt Route_table to configure the static routing table 1 From the MAIN MENU select Server and then press Enter CN2610 8_19 V2 0 Server RR Xeyaicamrct i oni oe S N Oh ons al Ws oA C19 or al OID Go Examine modify async se
28. None yes None Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 1 1 5 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection 12 13 CN2610 User s Manual Setting Up Dial in Out 4 Press ESC to return to the PORT MENU Configuring Modem Initialization Open Port Menu gt Modem to configure modem dial out initialization and dial out phone numbers 1 From the MAIN MENU use the arrow keys to select Port and then press Enter Ch else V250 Server Rxeaeal seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select mOdem and then press Enter Mode Line mOdem Welcome_MSG Quit Modem initialization and dial out setting Enter select ESC previous menu 3 The Modem page has input display fields for Enable Initialize Dialup and Phone number for each serial port Each item is described in detail below the figure CHAS LOSES LST ve Mode Line mOdem Welcome_MSG Quit Modem initialization and dial out setting ESC back
29. rhosts in this directory Enter the CN2610 s IP address e g 192 168 205 21 inthe rhosts file or enter the CN2610 s domain name if it s defined in your etc hosts file 4 Telnet the CN2610 s IP address 5 After entering the CN2610 s MAIN MENU select Utility gt Upgrade Ping Monitor Diagnostic Upgrade Quit Upgrade operational system program Enter select ESC previous menu 6 Inthe Upgrade via column select Network host using RCP CN2610 8_19 V2 0 Bao Ko os oo aE DB Ko potol henie Upgrade Quit Upgrade operational system program ESC back to menu Enter select Console port using XMODEM Upgrade via Host name IP address File name User name Presa ICIMRIL SUP Tee Siceliaie 6 5 7 In Host name IP address enter the IP address of the UNIX LINUX host 8 In File name enter the CN2610 firmware file name in the UNIX LINUX host 9 In User name enter the user name for logging into the UNIX LINUX host 10 Press CTRL U to start 16 15 CN2610 User s Manual Administrative Utilities 11 After downloading the CN2610 will restart the system SOOS rT Bane Vomito DiaCmostie Upgrade Quit Upgrade operational system program ESC back to menu Enter select Upgrade via Host name IP address File name User name home john CN2610 rom ohn Press CTRO U EO Siceliat o oo Windows Driver Manager Utility Installing CN2610 Windows Driv
30. 0 for no expires Login time interval in a day 08 00 22 00 The user has only 60 minutes in each login session 0 for unlimited 24 hours usage Barred login days Sun Sat The user is not allowed to login in on Saturday or Sunday 0 for accept 1 for reject Maximum login hours 500 The user has max 500 hours for this account 0 means unlimited access Select OK to save User Settings 4 User Permission Administration 4 gt odify User Permission Basic Permission Maintenance Extended Permission Maintenance Save amp Exit User List lists all UNIX LINUX users CN2610 User s Manual RADIUS Server gt dm bin daemon ftp games gdm george gopher halt 1p 1 Select the user george and press Enter to modify settings Press Ctrl F for page down Ctrl B for page up 2 Specify basic permission group and extended group for the user george 4 User Name george 4 Basic Permission Group Example 1 gt xtended Permission Group Example 2 Ok 4
31. 01 asprint dev iop1 CN2610 IP address 2048 amp Start asprint utility to read from pipe iopl and write to the CN2610 printer port dev iop1 the device name the spooler is writing to CN2610 the host name of the CN2610 as defined in etc hosts or its IP address 2048 the TCP port number Group01 of the printer port on the CN2610 accept printer Laser usr lib accept Laser 1 Set Laser 1 to accept print request enable Laser1 enable printer Laser enable Laser1 print file to Laser1 lp dLaser1 file_name send print job to the CN2610 Repeat Repeat the above steps to set up another printer For printers in the same group it is not necessary to repeat every step 13 11 CN2610 User s Manual Setting Up Printer Setting up a LINUX Host Steps SCO UNIX Command Description Uncompress all programs tar dev fdO Uncompress printer tar Z to printer tar xvf printer tar Z compile link make f sco_unix mak make printer node mknod dev iop1 p Create a unique pipe name for each printer group Since there are 16 groups of TCP port numbers from 2048 to 2063 you need to create 16 respective pipe names For example iop1 iop2 iop3 etc set it to printer chown lp dev iop1 Change the pipe owner to 1p set rw chmod 600 dev iop Change access permission to 600 or TW
32. 04 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM ASPP Async Server Proprietary Protocol 06 Printer RAW PRN Raw serial port printer mode 07 NT Real COM ASPP Async Server Proprietary Protocol 4 The pop up selector contains input display fields for Group TCP Pcort number and TCP alive check time Each item is described in detail below the figure Group TCP port number 8 AASR TCP alive check time 0 minutes Setting Value Notes Necessity Group Group 01 16 Groups printers attached to different ports Optional Printers in the same group will share the printing load for printing requests to that group of printers E g setting the CN2610 s serial ports 1 3 and 6 for Group01 will allow the printers attached to these three ports to act essentially as one printer TCP port 2048 2063 number The host uses this value to determine which Fixed Group the printer attached to this serial port belongs to These values are fixed and cannot be changed by the user Group TCP Port No Ol 2048 02 2049 03 2050 16 2063 TCP alive 0 99 minutes The time period the CN2610 waits before Optional check time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 5 Press Esc to return to the PORT MENU 13 5 CN2610 User s Manual Setting Up Printer Configuring L
33. 3 Select OK to save RADIUS proxy Configuration gt Proxy Server Administration gt Add Proxy Server Configuration Basic Configuration User Permission Administration gt roxy Server Administration 4 4 Proxy Server Administration 4 gt dd Proxy Server Modify Proxy Server Delete Proxy Server Save amp Exit 4 Add Proxy Server 4 gt P Address Name Radius Hash Key Ok IP address gt Proxy Server IP Name gt Proxy Server Name Radius Hash Key gt RADIUS encryption key must be the same key in the proxy server end Select OK to save B 10 CN2610 User s Manual RADIUS Server Setting up Windows NT Hosts Install Windows NT OPTION PACK 4 0 to Windows NT server 1 Start gt Programs gt Windows NT 4 0 Option Pack gt Microsoft Internet Information Server gt Management Console Manger Programs salAccessories Internet Expl
34. Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 15 2 CN2610 User s Manual Setting Up Routing What is RIP RIP Routing Information Protocol is a protocol used widely to manage routing information within a self contained network such as a corporate LAN Local Area Network or an interconnected group of such LANs By using RIP
35. Apply All Selected Ports These options will be saved on registry and used on few applications such as serial printer driver In general case you can ignore these settings Baud Rate o0 t i Parity None Data Bits b H Stop Bits hooo n Flow Control None XM Cancel Click the Security tab to configure security settings Select the Enable Data Encryption option to enable data to be encrypted when transmitted over the COM ports After selecting the encryption option select the Keep connection option to start encrypting COM port communications immediately without restarting the COM ports If your application will open close a COM port frequently and the CN2610 is only used for one host you can enable this option to speed up the opening closing time However this will result in your host tying up the COM port so that other hosts cannot use it Select the Apply All Selected Ports option to enable the security settings to be applied to all COM ports 16 25 CN2610 User s Manual Administrative Utilities 12 COM Port Setting Apply All Selected Parts J Enable Data Encryption Keep connection To save the configuration to a text file select Export from the COM Mapping menu You will then be able to import this configuration file to another host and use the same COM Mapping settings in the other host NPort Windows Driver Manager 192 168 127 2 57 Pot 1 68 54 950 192
36. Authentication None local None Authentication is not required Optional type server local Check the ID stored in the User_table defined under the SERVER MENU Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information TCP alive check 0 99 minutes The time period the CN2610 waits before Optional time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 8 Repeat the previous steps for ports 5 7 and 8 CN2Z26 10 8 9 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting Omi NT Real COM ASEP Async Server Proprietary Protocol 02 NT Real COM ASPP Async Server Proprietary Protocol GS NT Real COM ASPP Async Server Proprietary Protocol 04 NT Real COM ASPP Async Server Proprietary Protocol GS Multiplex RTELNET Reverse Telnet mode 06 Multiplex RTELNET Reverse Telnet mode 07 Multiplex RTELNET Reverse Telnet mode 08 RTELNET Reverse Telnet mode 14 6 CN2610 User s Manual Setting Up Multiplexor Configuring the Device CN2610 1 From the MAIN MENU select Port and then press Enter Server Port seTting sAve Utility Restart Exit Examine modify async server ports configuration Ente
37. Dialin fout ff Server Proprietary Protocol 03 Real COM Terminal Server Proprietary Protocol 04 Real COM Reverse Terminal Server Proprietary Protocol 05 BECERRO Device Control Server Proprietary Protocol 06 Real COM Multiplex Server Proprietary Protocol ag Real COM Printer Server Proprictary Procvocol NT Real COM DRDAS Raw UDP 08 Real COM PUM epost tera e muvee Server Proprietary Protocol Redundant COM 12 3 CN2610 User s Manual Setting Up Dial in Out 5 The Dialin out application supports five operation modes DYNAMIC PPP PPPD SLIP SLIPD DYNAMIC mode is selected by default CN2610 8_19 v2 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Server Proprietary Protocol NT Real COM Server Proprietary Protocol NT Real COM f gt Server Proprietary Protocol NT Real COM Server Proprietary Protocol NT Real COM gt Server Proprietary Protocol DYNAMIC Auto Term SLIP PPP identification NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Configuring PPPD PPP Mode PPPD PPP on demand is used for dial in services since it provides PPP services only when receiving a request from a remote PC PPP provides standard PPP services for both dial in and dial out 1 Move the cursor to th
38. ESC back to menu Enter select Port Application Description more setting 01 Real COM Server Proprietary Protocol 02 Real COM gt Server Proprietary Protocol 03 Real COM gt Server Proprietary Protocol 04 Real COM fi gt Server Proprietary Protocol 05 BECERRO f gt Server Proprietary Protocol 06 Printer A Raw serial port printer mode NT Real COM Async Server Proprietary Protocol Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application Description more setting O01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol NT NT 04 Real COM rver Proprietary Protocol 05 Real COM RAW PRN rver Proprietary Protocol 06 Printer al port printer mode Real C t rver Proprietary Protocol Real C Async Server Proprietary Protocol 07 08 NT NT 13 4 CN2610 User s Manual Setting Up Printer 3 Move the cursor to the Description more setting column and then press Enter Mode Line mOdem Welcome_MS Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 NT Real COM ASPP Async Server Proprietary Protocol 02 NT Real COM ASPP Async Server Proprietary Protocol 03 NT Real COM ASPP Async Server Proprietary Protocol
39. No Depends on whether the remote user s Optional compression application requests compression Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect Link quality Yes No If you are using software to collect Link Optional report quality information choose YES Outgoing PAP ID Dial out user account ID information Optional ID PAP password Password Dial out user account password Optional 12 5 CN2610 User s Manual Setting Up Dial in Out Setting Value Notes Necessity Incoming PAP None local server None Authentication is not required Optional check local Check the ID stored in the User_table defined under the SERVER MENU You will need to configure the user s information later in this chapter Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information 5 Press Esc to return to the PORT MENU Configuring SLIPD SLIP Mode The CN2610 supports SLIP Serial Line Internet Protocol and SLIPD for Dial in services only 1 Move the cursor to the Mode column for the port and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting jal NT Real COM ASPP Async Server Proprietary Protocol 02 NT Real COM ASPP Asyn
40. Ports ccs csesciistecgeisveeseseeesessteceesdeyin caves teases RE N NASE inir s 4 5 Savenn er a E E A r some bduweWitbdareuudadtes atssesesttaa E A 4 6 Res a r i a 4 7 SELLING Up OSES AE N AEE T E E E E E E EEEE 4 7 Setting up Windows XP 2003 Hosts sssesseseesseeseseseseeesrsreerssrerresesrrsresreeresreresse 4 7 Setting up Windows 2000 Hosts sseeseseesseseeseeresesesrsesreetessrstsrsrtessesrrreererserseseeee 4 25 Setting up Windows 95 98 ME NT Hosts sssssseseseesrsseeresesrsesrrreereresrsesrrrrerereeee 4 38 Setting Up Device Control ccceccceseseeeeeesseeeeeeeseeeeeeeeeseeeeeeseeeeeeenseenes 5 1 Accessing the Console Utility nuiis errr T TEE E E E E E 5 2 Selecting th Application ses saiae irasi aod a s Eai r h aA 5 3 Configuring ASPP Mode seios aoaaa ereer ateo e reaa o ao oa SEERA EERE SEEE EE ESAE TE RETEA 5 4 Confisurme RAW Mode diest iei erreen ain ibe Bees EE EE EEE E E E A e E EE 5 6 Configirin the Serral Ports ainese iei tne i E T TEE ee E EE 5 8 SAV EE E E E EEEE E E E E T 5 9 REStArt ASEE EERE T A T 5 9 ASPE Library Introductions rgen eee ties cnn chi ee SEE EEE EE EEE 5 10 ASPE Examples forUnix s4 ira rE ea alee anise bon ete SA 5 10 ASPP Examples for Windows ssccssescsseecceseeseesecseesccneesecsaeencssecaseecsaecaeesecsevseenaeeeeeas 5 11 Setting Up Raw UDP aisig anian ihaute aniria aetna eee 6 1 Accessing the Console Utility ac1 5 4 150 siewninuial ie daheisige aivaileeaan
41. Proprietary Protocol 03 Real COM ASPP Async Server Proprietary Protocol 04 Real COM ASPP Async Server Proprietary Protocol cS Real COM ASPP Async Server Proprietary Protocol i if 06 Printer LPD PRN LPD serial port printer mode 07 NT Real COM ASPP Async Server Proprietary Protocol 4 The pop up selector contains input display fields for Queue name lt RA W gt Queue name lt ASCII gt Append Form Feed and TCP alive check time Each item is described in detail below the figure Queue name lt RAW gt Queue name lt ASCII gt Append Form Feed Disable TCP alive check time oi min 13 6 CN2610 User s Manual Setting Up Printer Setting Value Notes Necessity Queue name Text Specify print queue s name in RAW mode Fixed RAW Queue name Text Specify print queue s name in ASCII mode Fixed ASCII Append Form Enable Specify paging Optional Feed Disable TOP alive 0 99 minutes The time period the CN2610 waits before Optional check time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter Server xeaml seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previo
42. Proprietary Protocol N Async Server Proprietary Protocol N Async Server Proprietary Protocol oi T Real COM T Real COM CZE S V2 0 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu EnteriRfoalcteu Pork Application t ption more setting 01 Real COM Disable Server Proprietary Protocol 02 Real COM Dialin out Server Proprietary Protocol 03 Real Terminal Server Proprietary Protocol 04 Real C Server Proprietary Protocol 05 Real C Device Control Server Proprietary Protocol 06 Real Multiplex Server Proprietary Protocol 07 Real C Printer Server Proprietary Protocol 08 Real C Mkea HO SEEN Server Proprietary Protocol NT Real COM DRDAS Raw UDP Redundant COM 9 3 CN2610 User s Manual Setting Up Reverse Terminal 5 The only operation mode associated with this application is Reverse Terminal mode which is selected automatically in the Mode column RTELNET mode allows Ethernet hosts to access serial hosts attached to the CN2610 s serial ports which is the reverse direction provided by the CN2610 s terminal application ICN2610 8 CN 26 O S ES Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application Mode Description more setting 01 NT Real COM ASPP Async Server Proprietary Protocol 02 NT Rea
43. Protocol 01 NT Real COM ASPP 02 NT Real COM ASPP 03 NT Real COM ASPP Async Server Proprietary Protocol NT Real COM ASPP Async Server Proprietary Protocol NT Real COM ASPP Async Server Proprietary Protocol Dialin out DYNAMIC ff Auto Term SLIP PPP identification NT Real COM ASPP Async Server Proprietary Protocol NT Real COM ASPP Async Server Proprietary Protocol CN2610 8 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select POr ae Qojon mor uemoyal Mode ID YNAM I CRKVA Or Soe 01 NT Real COM ASPP PPP xver Proprietary Protocol 02 NT Real COM ASPP BERD rver Proprietary Protocol 03 NT Real COM ASPP SLIP rver Proprietary Protocol 04 NT Real COM ASPP rver Proprietary Protocol 05 NT Real COM ASPP t rver Proprietary Protocol 06 Dialin out DYNAMIC Auto Term SLIP PPP identification 07 NT Real COM ASPP Async Server Proprietary Protocol 08 NT Real COM ASPP Async Server Proprietary Protocol 12 8 CN2610 User s Manual Setting Up Dial in Out 3 Move the cursor to the Description more setting column and then press Enter CN2610 8 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 NT Real COM ASPP Async Server Proprietary Protocol 02 NT Real COM ASPP Async Server Proprie
44. RCP Import As we pointed out earlier RCP is a file transfer protocol that does not require a password 1 Login to your UNIX LINUX host For example login to 203 67 8 22 as user john 2 Create a file named rhosts in this directory Enter the CN2610 s IP address e g 192 168 205 21 or the CN2610 s domain name if it s defined in your etc hosts file in the rhosts file 3 Telnet the CN2610 s IP address 4 After accessing the CN2610 s MAIN MENU select seTting gt Import In Import via column select Network host using RCP 5 Enter the UNIX LINUX host s IP address for Host name IP address 6 Enter the CN2610 s firmware file name on the UNIX LINUX host for File name Enter the user name required to login to the UNIX LINUX host for User name 16 38 CN2610 User s Manual Administrative Utilities 8 Press CTRL U to start V2 61 0 8 OOOO N2608 19 V2 O O soora Import SEEST yee Ro Ei Import configuration from previously saved file ESC back to menu Enter select Import via Host name IP address File name User name Network host using RCP PUSS eres home john CN2610 rom john Pressi CAMRIL UW ee iseeliete Default The CN2610 can restore default settings if necessary Note that the IP address will not be changed to default 1 From the MAIN MENU select seTting and then press Enter Cho IG ro y0 Server Port I SseTting sAve Utility Restart Exit Bxpork wrcin
45. Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Unix fixtty driver mode NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Configuring FIXTTY Mode 1 Move cursor to the Description more setting column and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting omi Real COM ASPP Async Server Proprietary Protocol 02 Real COM ASPP Async Server Proprietary Protocol 03 Xt LO ASPP Async Server Proprietary Protocol 04 Real COM ASPP Async Server Proprietary Protocol 05 Real COM ASPP Async Server Proprietary Protocol 06 Mala HOSEN FIXTLY nix fixtty driver mode 07 NT Real COM ASPP Async Server Proprietary Protocol 2 The pop up selector contains input display fields for Max Sessions Terminal model no Inactivity time TCP alive check time and also Session parameters Each item is described in detail below the figure Max Sessions Terminal model no Inactivity time 8 minutes TCP alive check time 0 minutes Session Hot key TER POTE Remote IP address 4001 en 2 3 4 5 6 7 8 11 4 CN2610 User s Manual Setting Up Multi Host TTY Setting Value Notes Necessity Max Sessions 1 8 Select the maximum number of Optional simultaneous sessions that wi
46. Socket programming in Linux Unix environments or WinSock programming in Windows environments Standard socket programming allows you to focus on pure data transmission without needing to write code for controlling serial ports or modem signals ASPP can also be used to communicate with the CN2610 Linux Unix socket programming and Windows WinSock programming both use IP as the communication agent between hosts and devices RAW mode is a good solution for handling pure serial data communications applications that do not require setting up communication parameters baudrate parity etc Refer to Chapter 5 for detailed information and configuration instructions UDP Communication Raw UDP i UDP datagram wo CN2610 j Serial Finger Printer UDP is a non connection oriented data transmission protocol that has the advantages of efficient high speed high volume data transmission Since UDP does not use TCP s handshaking procedure it does not re assemble and retransmit packets when data is missing This means that data integrity is sacrificed for higher transmission speed UDP provides a very powerful transmission method when data needs to be transmitted quickly over the network and upper level application software is given the responsibility of verifying the accuracy of the data UDP can also use broadcasting or multicasting technologies to handle point to multi point transmissions UDP is
47. The installation procedure for Windows 2003 machines is identical 4 7 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Installing a Server 1 Unzip the Windows XP 2003 driver file located on the CN2610 CD ROM to your hard disk 2 Run the Windows Add Hardware Wizard located in the Control Panel 10 x File Edit view Favorites Tools Help aw Oix O B J seah gt Folders ETA o aig g Administrative Tools wo Automatic Date and Time Display Folder Options 3 When the Welcome to the Add Hardware Wizard window opens click Next to continue Add Hardware Wizard Welcome to the Add Hardware Wizard Pa We Y This wizard helps you Install software to support the hardware you add to your computer Troubleshoot problems you may be having with your hardware amp If your hardware came with an installation CD it is recommended that you click Cancel to close this wizard and use the manufacturer s CD to install this hardware To continue click Next lt Back if F Cancel 4 8 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 4 Wait patiently while the Wizard searches for servers connected to the network Add Hardware Wizard Please wait while the wizard searches 5 The next window to open will ask you if the hardware is connected Select Yes I have already connected the hardware and
48. You had modified the configuration without saving Would you save it now You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel CHASO S VO Server Port seTting OVERES a eE E Save current configuration to Flash ROM ESC back to menu Enter select Restart 1 From the MAIN MENU select Restart CN2610 PIa o a o S A R Restart Mibene Restart the whole system or selected async ports Enter select ESC previous menu 2 Select System and then press Enter to restart the system and terminate the Telnet session System Bzehae Quit Restart the Async Server ESC back to menu Enter select Warning I Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 11 7 CN2610 User s Manual Setting Up Multi Host TTY Setting up Hosts Installing and Compiling Fixed TTY Driver Installing and Compiling 1 4 Create a directory for Fixed TTY driver e g user etc as shown below mkdir usr etc cd usr etc Extract code from the tar formatted file moxattyd tar as follows tar xvf moxattyd tar After the extraction is complete locate the following files moxattyd c program source code moxattyd cf configuration file Makefile README TXT description file for Fixed TTY driver VERSION TXT driver version Compile and link documents SCO Ope
49. an ideal transmission method for serial devices that must transmit data to a group of devices or PCs Refer to Chapter 6 for detailed information and configuration instructions 3 4 CN2610 User s Manual Knowing Your Application Dual host Redundant Data Acquisition System DRDAS lpi PC Backup PC Wing LAN B Primary RS 232 422 485 Data Remote Terminal Unit RTU The DRDAS operation mode provides a highly redundant network structure that takes advantage of the CN2610 s dual LAN ports dual IP addresses and dual MAC addresses DRDAS uses a backup PC that is set up to take over when the primary PC fails The CN2610 s dual host redundant configuration sends serial data to 4 IP addresses on the network Users select a Primary IP and 3 Secondary IPs When the Primary IP fails the backup IPs take over by using the switching library refer to Chapter 7 for more details With this kind of redundant setup if one of the secondary IPs tries to send commands to the serial device the commands are discarded by the CN2610 since only the Primary IP is allowed to conduct bi directional transmission The backup IPs are only allowed to receive data from the CN2610 CN2610 User s Manual Knowing Your Application NOTE Primary PC Backup PC Primary RS 232 422 485 amp Remote Terminal Unit RTU This type of highly redundant setup is implemented with two CN2610s as sho
50. configuration without saving Would you save it now Y yes You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel CRASS S VAO Server Port seTting Utility Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select Restart 1 From the MAIN MENU select Restart CHA61 Ose L VO isan a ola et oTe S AV Restart Mipeme Restart the whole system or selected async ports Enter select ESC previous menu 12 16 CN2610 User s Manual Setting Up Dial in Out 2 Select System and then press Enter to restart the system and terminate the Telnet session 102 61 0 2 7 OOO OO System Bzenae Quit Restart the Async Server ESC back to menu Enter select Watning 114 Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 12 17 13 Setting Up Printer In this chapter we describe how to set up the CN2610 as a printer server Up to 16 serial printers can be connected simultaneously to one CN2610 At the end of the chapter the settings needed for one port parallel printing is illustrated for both UNIX and Windows systems The following topics are covered in this chapter Accessing the Console Utility Selecting the Application Configuring RAW PRN Mode Configuring LPD PRN Mode Configuring the Serial Ports Save Restart Setting up
51. csssescpscnse slush ypsoseotiteeh aabeasssihstathabtpssseeattesteasbagavionsase 2 4 Configuration Checklist c2 sui e Heid ne biel eE E E N 2 4 Accessing the Console from a Telnet Terminal cc ceeesecsseesessecreesecnereeeeaeeees 2 4 Accessing the Console from a Console Terminal 0 csseecsseeceeseceeeeeeeceeeeners 2 7 Configuring the CN2610 The Server Menu eceesesssecseesecneeeececsereeceaeeeesaeeaseseenees 2 13 Server Configuration Info 00 ccecesesseesecseseeceseeeceseceeesecneeecsaseeeaecaeesecnesseeeeens 2 13 Server Configuration LAN sccessesssesecseeseceseeecesecaeesecneesecsaeeeeaecaeesesnesseeeaees 2 14 Server Configuration AdV 0 cccescesesecssseecesecseesecneeseesecneesecsaseceaecaeeseenerseeeaees 2 16 Server Configuration Host_table eccecccescceeeeeseceseeeeceseceseceeeceecaeeeneeeaeeeeeeenees 2 17 Server Configuration Route_table ecceccceceesecesecesecececeeeeseeeeeeeeeeeeeeerenerensees 2 18 Server Configuration User_table cceeccecccescceseceseceeecececeeeeeeeeneeseeeeeeeseenerensees 2 19 DAVE REA subens cuss Vives Sobtee tusk E E E subdue tusvsdusteachite Sounieus EET 2 20 REStAME AE eiinds sees asco tan E ddituc dass svtocis E A 2 20 Knowing Your Application ccccccccccsssseeeeeeeeeeeeenseseeeeeeeneeeeeeeeeeeeeenees 3 1 Windows Real COM NT Real COM ccccccccccccsssscecsecececssceecessececseaaecessnseeesenseeensaeees 3 2 Linux Real TTY Unix F
52. each serial port Each item is described in detail below the figure CNAS TO re 7 a Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed Parity FIFO RIS CTS XON XOFF DISCON coe top Oh 15200 1 None yes None 02 C1152090 i None f yes None 03 Paka AO iL None s yes None 04 PLS 2 0103 alae None i yes None ala 115200 Laii None amp yes None 06 ELS ZOO aari None i yes None 07 CLS 2001 i 4 None yes None 08 115200 itl None f yes None Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 1 1 5 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection 4 Press ESC to return to the PORT MENU 11 6 CN2610 User s Manual Setting Up Multi Host TTY Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save j SERVER MENU Iesous Oe oE Oo USer table Roti Examine modify async server basic configuration Enter select ESC previous menu Warning id
53. ely e A Os oE olla mma lolk mm USer table Mebane Examine modify async server basic configuration Enter select ESC previous menu Warning 11 You had modified the configuration without saving Would you save it now te yes 10 10 CN2610 User s Manual Setting Up Terminal You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel CHASO S W230 Server Port seTting Uee Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select Restart 1 From the MAIN MENU select Restart CN2610 isan sae ola 1S on ole men Wena Restart Eei Restart the whole system or selected async ports Enter select ESC previous menu 2 Select System and then press Enter to restart the system and terminate the Telnet session System SEZs Quit Restart the Async Server ESC back to menu Enter select Warning 11 Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 10 11 11 Setting Up Multi host TTY The Multi host TTY application is the ideal transmission method for communicating with multiple Unix hosts over the network via several simultaneous sessions When the communication starts a Unix server connected to the network must first activate Moxattyd to use the TTY port s mapping function Moxattyd will initiate the connection with
54. eneen aeaeaei speech ees E OEN E SEE aSa soe B 2 Setting up the CN261 0s meree hirren ea eee ee aeea EEE ERSE e EE T a R A SS ale B 2 Setting up the RADIUS Server IP Address s eseeeeeeeeeeeeeesreeseerersesrrrrererrsesrse B 2 Setting up Port Configuration sssessesesesesseesessssestseserretsrsesrsterretsrsesrerrereessesrsree B 3 Setting p UNIX HOSTS raen erpa e erie eree e EAEE EE E a vepedeapvanunedeoorees B 5 Installing the RADIUS Execution File ccc eeessesecseeeeceeeeeceeceeseecsaeeeeeseeneeseenees B 5 RADIUS Server Configuration zinasema r e a ari B 6 Basic Extended Permission Group Setting eseeeeeeeseeeiesesrsesisrerrersrsrerrereesesrrreerees B 7 Setting up Windows NT Hosts esesscsesscsseeeceseseeeecaeceeesecaeesecnaeeecsaeeeesaesaeeeeeneseneeaees B 11 Setting up Windows 2000 Hosts 0 0 cceecsescsscseseeceseeeceseceeesecseesecnaeeeceaeceesaecaeeseeneseeeeaees B 13 Setting up Windows 2003 Hosts sarene enra a e a r eiae B 16 SNMP Agent with MIB II ccescsseecesseeeeeeeeseeeeeesseeeeeeeseeeeeeeesseeeeeeeeeees C 1 Pin Assignments and Cable Wiring ecccsesseeeeeeeeeeeeeneeeeeeeeneeeeeees D 1 Pin ASSISNMENS oe e veneers nbs cu wanbenes a e a S EE E A a oh D 2 10 100BaseTX Port Pin Assignment ssesseeeeseseeeseseeeeereesrsrsrterererssesrsreerereersesrees D 2 Console Port Pin Assignment cece oeeo ir ioen oeii eeose oaee ipe sees Si D 2 Async RS 232 Port Pin Assignment essssescseessce
55. mode is recommended if you want to ensure that all data is sent out before further processing FIFO If FIFO is Disabled the CN2610 will transmit one byte each time the Tx FIFO becomes empty and an Rx interrupt will be generated for each incoming byte This will result in a faster response and lower throughput Network Timeout You can use this option to prevent blocking if the target CN2610 is unavailable Auto Network Re Connection With this option enabled the driver will repeatedly attempt to re establish the TCP connection if the CN2610 does not respond to background check alive packets Return error if network is unavailable If this option is disabled the driver will not return any error even when a connection cannot be established to the CN2610 With this option enabled calling the Win32 Comm function will result in the error return code STATUS_NETWORK_UNREACHABLE when a connection cannot be established to the CN2610 This usually means that your host s network connection is down perhaps due to a cable being disconnected However if you can reach other network devices it may be that the CN2610 is not powered on or is disconnected Not that Auto Network Re Connection must be enabled in order to use this function 16 24 CN2610 User s Manual Administrative Utilities Fast Flush only flushes the local buffer For some applications the user s program will use the Win32 PurgeComm function before it
56. of Server you will need to configure the User_table for user authentication The User_table page is also used to activate the call back function 1 From the MAIN MENU use the arrow keys to select Server and then press Enter CNG Loser Server Bixehqumrci uu g sAve Utility Restart Ex Examine modify async server node table configuration Enter select ESC previous menu 2 From the SERVER MENU select User_table and then press Enter Zr SERVER MENU ab obo Pann esoe A O oE O User_table Mm bnne Examine modify the user password table Enter select ESC previous menu 12 15 CN2610 User s Manual Setting Up Dial in Out 3 The User_table page has input fields for User name Password and Phone Number for each serial port Input a Phone Number to activate the automatic call back function Note that the CN2610 can store information for up to 64 users Chee LO G2 To YZ ab obo pan iT 0 oly oh aun s ol ummr loln Ma O mme lolk mem USer table Mebane Examine modify the user password table ESC back to menu Enter select User name Password Phone Number 4 Press Esc to return to the MAIN MENU Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save CNAE Qe sabe ye O ib obo an esoe A O oE Colla mae lolm mm USer table Mebane Examine modify async server basic configuration Enter select ESC previous menu Warning tl You had modified the
57. of the two LANs fails the other LAN will continue transmitting packets between the serial devices and the host with the packets passing through the CN2610 In fact one of the biggest advantages of the CN2610 s Redundant COM mode is that the switching time is zero 3 7 CN2610 User s Manual Knowing Your Application Console Management Reverse Terminal ya f 3 A Windows NT TCP IP CN2610 lt Router Server Server The Reverse Terminal application which uses Rtelnet mode is used with routers switches and UPS equipment for console management applications Rtelnet mode is similar to RAW mode in that after booting up it listens to one specific TCP port for network hosts to initiate a connection RAW mode however does not provide a Telnet conversion function If the serial devices connected to the CN2610 need to use the CR LF conversion function then Rtelnet mode must be used The CN2610 s Rtelnet mode is also used widely for device management applications in telecommunication control rooms since remote hosts can make use of Local User Table or RADIUS identity verification methods Refer to Chapter 8 for detailed information and configuration instructions 3 8 CN2610 User s Manual Knowing Your Application Terminal Access Terminal Windows NT Unix a e are CN2610 TCP IP z A 5 Be a Terminal Terminal Terminal The CN2610 s T
58. option Mark P a P i t y T M a ba k To choose the desired option press the SEL button when the option is showing on the screen E 3
59. printer is installed properly you can print a test page 13 20 CN2610 User s Manual Setting Up Printer 11 If you want to print a test page reboot Windows 2000 select this printer and click Print Test Page E Generic Text Only Properties RTE Device Settings Printer Commands Font Selection General Sharing Ports Advanced Security je Genetic Text Only Location Test Cube Comment E printer Model Generic Text Only m Features Color No Paper available Double sided No Letter Staple No Speed Unknown Maximum resolution 600 dpi z Printing Preferences Print Test Page CY Cancel Apply 13 21 14 Setting Up Multiplex In this chapter we describe how to configure the CN2610 as a Multiplexor and De Multiplexor Using the Multiplexor De Multiplexor application requires two Async Servers one attached to a host with a multi port serial board and several serial lines and the other connected to external devices In this way the original host can use a TCP IP connection to control serial devices from a remote location The following topics are covered in this chapter Accessing the Console Utility Selecting the Application Configuring the Host CN2610 Configuring the Device CN2610 Configuring the Serial Ports Save Restart OOOCUUOCD CN2610 User s Manual Setting Up Multiplexor Accessing the Console Utility
60. server local Check the ID stored in the User_table defined under the SERVER MENU Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information TCP alive check 0 99 minutes The time period the CN2610 waits before Optional time checking if the TCP connection is alive Press Esc to return to the PORT MENU 10 6 CN2610 User s Manual Setting Up Terminal Configuring TERM_BIN Mode TERM_BIN Terminal Binary mode is used as an application protocol For example it can be used to transfer files with XMODEM or ZMODEM You are only allowed to open one terminal session at a time when in Terminal Binary mode 1 Move the cursor to the Mode column for the port and press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting on Real COM Async Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Real COM Async Server Proprietary Protocol 04 Real COM Async Server Proprietary Protocol 05 Real COM Async Server Proprietary Protocol 06 Terminal ASCII Termianl mode 8 sessions o Real COM Async Server Proprietary Protocol 2 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Por Application Description more setting 01 NT Real COM Async Se
61. sio_write fd buf len write data 11 sio_read fd buf len tread data 12 sio_break fd time send break signals 13 sio_oqueue fd check how much data is in the output buffer 14 sio_iqueue fd check how much data is in the input buffer ASPP Examples for Unix In general controlling devices attached to ASPP ports involves using the following procedures 1 Create a socket for the command port and then connect to the port 2 Configure the port s serial parameters such as baudrate via the command port 3 Create a socket for the data port and then connect to the port 4 Transfer data via the data port This example program continually sends the string 1234567890 to the CN2610 s ASPP port and then reads back data when the program ends Settings Target port parity None data bits 8 stop bit 1 software XON XOFF flow control no hardware RTS CTS Syntax example ConsoleServerName port 1 Baud 9600 For example example CN2610 1 19200 Program sends 1234567890 to port 1 at 19200 bps baudrate and reads back any data on it Environment SCO UNIX If you re using another system modify by including the file name and other variables 5 10 CN2610 User s Manual Setting Up Device Control ASPP Examples for Windows 1 Program testing environment Ethernet ns 232 CN2610 a Terminal Windows PC running as exe 2 This program works like a dum
62. table Mebane Examine modify async server basic configuration Enter select ESC previous menu Warning 11 You had modified the configuration without saving Would you save it now te yes CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel CHASO S 420 Server Port seTting Uila Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select Restart 1 From the MAIN MENU select Restart CN2610 8_19 V2 0 isan sae ola 1S on ole men Wena Restart Eei Restart the whole system or selected async ports Enter select ESC previous menu 2 Select System and then press Enter to restart the system and terminate the Telnet session CNZG LO 1 V20 System SEZs Quit Restart the Async Server ESC back to menu Enter select Warning 11 Restart system will disconnect all ports and clear all status value Enter continue ESC cancel Setting up Hosts After using the CN2610 Console Utility to set up Async Server s ports for the NT Real COM application ASPP mode you will need to install port drivers on every computer used to access the CN2610 s ports In this section we explain how to set up Windows hosts Setting up Windows XP 2003 Hosts In this section we use Windows XP to illustrate the installation procedure
63. the Primary IP is the only IP address that can conduct by directional transmission The backup IPs can only receive data from the CN2610 but cannot send commands to the serial device Setting Value Notes Necessity TCP data port number Via the data port users can retrieve data through Yes the async line TCP command number Via the command port users can issue commands Yes port across the network to set the line s configuration parameters such as baudrate data bits flow control condition etc Primary IP addr IP address The primary host s IP address Yes If left blank then every host on the network cannot access the serial port Backup 1 IP addr IP address Backup host s IP address Optional Backup 2 IP addr IP address Backup host s IP address Optional Backup 3 IP addr IP address Backup host s IP address Optional TCP alive check 0 99 minute Specifies the time slice for checking whether the Optional time TCP connection is alive If there is no response the CN2610 will reset the port and disconnect the original connection 3 Press Esc to return to PORT MENU Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter CNAE OSB NS oe Server xeaet seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu
64. the whole system or selected async ports Enter select ESC previous menu 2 Select System and then press Enter to restart the system and terminate the Telnet session System Bi zehae Quit Restart the Async Server ESC back to menu Enter select Warning Restart system will disconnect all ports and clear all status value Enter continue ESC ca cel 15 8 16 Administrative Utilities In this chapter we show how to use the CN2610 administrative utilities which include Ping to see if a LAN host is still active and how to get information with Monitor gt Line Monitor gt Network Monitor gt Async Monitor gt Routing and Monitor gt PPP Trace The following topics are covered in this chapter O Ping Monitor gt Line gt Network gt Async gt Routing gt PPP Trace O Diagnostic O Upgrade gt Upgrading with the Windows Utility gt Console Terminal Upgrade gt Upgrading through the Serial Console gt Remote RCP Upgrade Q Windows Driver Manager Utility gt Installing CN2610 Windows Driver Manager gt Error Reference source not found Q Windows Monitor Utility gt Installing CN2610 NPort Monitor Utility gt Using NPort Monitor Utility Export gt Console Terminal Export gt Remote RCP Export QO Import gt Console Terminal Import gt Remote RCP Import O Default CN2610 User s Manual Administrative Utilities Ping Ping is used to test network hardware con
65. to PORT MENU CN2610 User s Manual Setting Up DRDAS Save 1 Press Y to save previous settings when exiting PORT MENU Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Warning If any field changed in this menu Restart System to take effect Press any key to continue 2 You may also save later From the MAIN MENU select sAve to save all changed settings and then press Enter to confirm Server Port seTting Yenlaty Restart Exit Dave current configuration to Flash ROM ESC back to menu Enter select Restart 1 Return to MAIN MENU and select Restart CELOS LS V7 sb isan ola et Seeley Wena Restart Eei Restart the whole system or selected async ports Enter select ESC previous menu 7 7 CN2610 User s Manual Setting Up DRDAS 2 Select System and then press Enter to continue 102 610 2 a VZO O OOOO OO System ELis Quit Restart the Async Server ESC back to menu Enter select Warning 00 0 Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 3 The system will restart and the Telnet Console session will terminate Enter the MAIN MENU again to check whether the settings have been changed 7 8 8 Setting Up Redundant COM Mode This chapter shows how to set up a CN2610 Async Server that allows the redundant terminal on the redundant Ethernet
66. wizard lt Back 4 17 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 6 After the installation is complete you can check Ports COM amp LPT under Device Manager to verify that all of the ports were installed successfully Zoevice Manager TST File Action view Help e gt m82 gt Keyboards T5 Mice and other pointing devices Monitors J Multi port serial adapters JD MOXA Async Server CN2510 8 E9 Network adapters A Ports COM amp LPT Communications Port COM1 J Communications Port COM2 F MOXA Communication Port 1 COM13 MOXA Communication Port 2 COM14 F MOXA Communication Port 3 COM15 F MOXA Communication Port 4 COM16 sj MOXA Communication Port 5 COM17 a MOXA Communication Port 6 COM18 F MOXA Communication Port 7 COM19 a MOXA Communication Port 8 COM20 F Printer Port LPT1 SM Processors Sound video and game controllers p System devices CCE D E CRER Configuring the CN2610 in a Windows XP 2003 Environment After the CN2610 driver is installed you will be given the option to proceed directly with the configuration of the CN2610 You may also configure the CN2610 at a later time In this section we explain how to configure Real COM Mapping 4 18 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 1 Click Device Manager gt Multiport serial adapters right click the CN2610 you wou
67. x amp Default NNTP si E Microsoft Transaction 5 Select Service Check the RADIUS ports Authentication 1645 Accounting 1646 6 Select Client and the click Add Enter the CN2610 s IP address in the IP address field Enter the CN2610 s password in the password field The password corresponds to the RADIUS key setting in the CN2610 Console RADIUS server IP 192 168 205 161 RADIUS key 123 UDP port 1 1645 2 1812 1 Enable RADIUS accounting yes SNHP connunity nane public SNHP trap server IP address Ethernet IP forwarding no Routing protocol None TCP retransmission timeout t SIO data transfor tineout 7 Click Apply 8 Right click RADIUS in the left info window and select Start 9 You will now see that RADIUS is running B 12 CN2610 User s Manual RADIUS Server Setting up Windows 2000 Hosts 1 Click Start gt Programs gt Administrative Tools gt Routing and Remote Access 2 Follow the steps below to install Right click on Server Local to select Configure and Enable Routing and Remote Access Click Next to continue 3 Select Remote access server and then click Next to continue Routing and Remote Access Action ri SS oe es A Eines Routing and Remote Access Server Setup Wizard x Tree Common Configurations You can select from several common configurations Routing aj Serv z
68. 10 NPort Monitor Utility iG Setup NPort Monitor Utility Completing the NPort Monitor Utility Setup Wizard Setup has finished installing NPort Monitor Utility on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup 16 29 CN2610 User s Manual Administrative Utilities Using NPort Monitor Utility After you install NPort Monitor Utility you can monitor the status for Redundant LAN 1 IP address MAC address LAN 2 IP address MAC address and status 1 Go to Start NPort Monitor Utility to start the monitor utility 2 Click the Search icon 3 Click Rescan to search for CN2610 terminal servers From the list that is generated select the server that you will monitor and then click OK searen j x Searching NPost s TCSTSTTSCSCSCSCTS Complete z Found 1 NPort s Rescan stop Select All Clear All _ Model MAC address 1 IP address 1 MAC address 2 IP address 2 M1 cN2610 16 00 90 68 10 81 67 192 168 34 219 00 90 E8 10 81 68 192 168 36 219 JS OK X Cancel 16 30 CN2610 User s Manual Administrative Utilities 4 The monitoring information will appear on the Monitoring page Select the IP address from the left hand side that you would like to monitor and then click the Start icon nort monitor veer alelxl Function Run Help i 2 k m Exit Search Start Stop B erver List
69. 168 126 254 951 192 168 127 254 952 968 Port3 192 168 126 254 952 968 192 168 127 254 953 969 Port4 192 168 126 254 953 969 192 168 127 254 954 970 Port5 192 168 126 254 954 970 192 168 127 254 955 971 Port6 192 168 126 254 955 971 192 168 127 254 956 972 Port 192 168 126 254 956 972 192 168 127 254 957 973 Port8 192 168 126 254 957 973 16 26 CN2610 User s Manual Administrative Utilities Windows Monitor Utility Installing CN2610 NPort Monitor Utility CN2610 NPort Monitor Utility is used to monitor the redundant COM mode connection status These drivers are designed for use with Windows 95 98 ME NT 2000 XP 2003 Vista 1 Click the INSTALL Monitor Utility button in the CN2610 Installation CD auto run window to install the CN2610 Monitor Utility Once the installation program starts running click Yes to proceed 2 Click Next when the Welcome screen opens to proceed with the installation 6 Setup NPort Monitor Utility Welcome to the NPort Monitor Utility Setup Wizard This will install NPort Monitor Utility Yer1 0 on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup j Cancel 16 27 CN2610 User s Manual Administrative Utilities 3 Click Next to install program files to the defau
70. 2 From the PORT MENU select Line and then press Enter NODECEE Line Mp u lel jt mere ma OE Examine modify asynchronous port configuration Enter select ESC previous menu 7 5 CN2610 User s Manual Setting Up DRDAS 3 Specify the relevant settings Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed STOP Parity FIFO RTS CTS XON XOFF Digenia Gral 1 15200 i None yes None 02 1152009 ag None yes None 03 115200 il None yes None 04 PIT5200 y None yes None D 115200 all None yes None 06 ESO dk None yes None 07 115200 all None yes None 08 115200 1 None yes None 09 115200 a None yes None T 115200 AL None yes l None AGL 115200 dl None yes None ie 115200 J None yes None TE PLS 200 dk None yes None 14 115200 il None yes None 15 LTT5200 None yes None 16 115200 dl None yes None Setting Value Notes Speed 50 to 921 6 Kbps Transmission speed Bits 5 6 7 8 Data bit Stop 1 1 5 2 Stop bit Parity None Even Odd Mark Space Parity check FIFO Yes No FIFO setting Default is Yes RTS CTS Yes No Hardware flow control XON XOFF Yes No Software flow control Discon Ctrl None DSR off DCD off Inactive for these modes 4 Repeat the above steps to set all lines 5 Press Esc to return
71. 200 all None yes yes no None 03 MAISZ00 dl None yes yes no None 04 LL SAO J None yes yes pete None 05 115200 J None yes yes no None 115200 ak None pete 115200 dl None J no ALLS 2O0 dl None no Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 151 5 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection 4 Press ESC to return to the Port Menu CN2610 User s Manual Setting Up Reverse Terminal Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save j SERVER MENU Iesous Oe oE Oo USer table Roti Examine modify async server basic configuration Enter select ESC previous menu Warning id You had modified the configuration without saving Would you save it now You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel CHASO S VO Server Port seTting OVERES a eE E Save current configuration to Flash ROM ESC back to menu Enter select Restart 1
72. 207 Redundant COM 192168 34 207 192 188 36 207 Redundant COM 192 188 34 207 192 168 386 207 Redundant COM 192168 34 207 192 168 386 207 Redundant COM 192 168 34 207 192 168 386 207 Redundant COM 132 168 34 207 z 192 168 386 207 Redundant COM 192 168 34 207 192 168 365 207 Redundant COM 192 168 34 207 192 168 386 207 Redundant COM 192 168 34 207 192 188 38 207 Redundant COM 192 168 34 207 192 188 38 207 16 31 CN2610 User s Manual Administrative Utilities Export RCP Settings can be exported to a file to backup the configuration or to set up another CN2610 with the same configuration There are two types of exported file settings Console Terminal or Remote Console Terminal Export 1 Run Start gt Programs gt PComm Terminal Emulator Follow the steps given earlier to enter the MAIN MENU 2 From the MAIN MENU select seTting and then press Enter EaPComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a alaj allele 32 A 115200 None 8 1 T100 In x CNZ510 8 5631 V2 0 Server Port Eyes asre sive Utility Restart Exit SC previous menu 3 From the SETTING MENU select Export and then press Enter EaPComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a la alele 32 kacor 115200 None 8 1 T100 lol x CN2510 8_5631 V2 0 TR SETTING MENUR Eta Import Default Quit ou
73. 5 5 CN2610 User s Manual Setting Up Routing For this example the Notebook PC dials in to the CN2610 to request a connection to Internet host 210 48 96 9 for example which is not on local network 203 67 6 This causes the CN2610 to act as a router and send the datagram to the default next hop router 203 67 6 254 In this case we should add the default gateway IP address 203 67 6 254 to the routing table as shown in the following figure to handle hops to any destination beyond the local network 203 67 6 gonado pan e o O sues Oa o ROUte table RAIRE o EO Examine modify the routing table ESC back to menu Enter select Gateway Destination Netmask Metric 203 601 6254 I 0 0 0 0 PRAO 01 01 Conn Configuring Routes to the Internet and Intranet 203 67 6 1 _ UNIX g Server Ethernet 203 67 6 TCP IP 203 67 6 252 CN2610 Router P Router r 203 67 6 253 Console Server 203 67 6 254 205 65 66 2 J Router Modem Modem Ethernet 202 65 66 1 A 4 A l pe 202 65 66 4 202 65 66 5 SF gt Internet N Qe 2 Notebook For this example in addition to sending requests to the Internet dial in users can make requests to Intranet hosts 202 65 66 4 or 202 65 66 5 which are on network 202 65 66 located outside network 203 67 6 In this case add a route entry for the next hop router 203 67 6 252 that delivers requests to network 202 65 66 Th
74. 610 Utility lists all available servers on the network Note that servers in grey are password protected Double click the server s name or click from the menu bar to see the server settings FN NPort Server firmware upgrade utility Server Tool Help General Info Model 1P Address SerialNo__ MAC address Firmware Ver CN2510 8 5631 CN2510 8 192 165 127 254 5631 00 90 E8 00 56 31 2 0 2 5 CN2610 User s Manual Getting Started 4 The server s general information is shown in the CN2610 Server General Info window If necessary change the settings and then click OK to accept the change NPort Server General Info x You may change Server Name or IP Address for selected NPort Server Server Name CN251 0 8_5631 IP Address 192 168 127 254 Model CN2510 8 Serial No 5631 MAC address 00 90 E8 00 56 31 Firmware Version 2 0 Cancel 5 If you can t find the server in the list double check the server s power and network connections and then use search to try locating the server again Using Telnet 1 Telnet over the network to the server s IP address Run 2x Type the name of a program folder document or F Internet resource and Windows will open it for you Open jtelnet 192 168 127 254 x Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52
75. 68 1 5 13 Select logical printer port for the LPR port you just added The LPF port should be the IP address of the port 13 15 CN2610 User s Manual Setting Up Printer 14 Select the printer s manufacturer and model name Click Next to continue Add Printer Wizard Generic IBM Graphics Spin Generic IBM Graphics Spin wide 15 Enter the printer s name and select yes if you wish to set this printer as the default printer Click Next to continue 16 Select Shared when prompted with questions asking if the printer is to be shared or not and then enter the name of the shared printer Add Printer Wizard windows NT 3 5 or 3 51 x86 Windows NT 3 5 or 3 51 MIPS 17 Print a test page to verify that the printer is configured correctly and then click OK to finish 13 16 CN2610 User s Manual Setting Up Printer Setting up a Windows 2000 Host 1 Click Start gt Settings gt Printers 2 Click Add Printer to start and Add Printer Wizard 3 A Welcome message will appear Click Next to continue Add Printer Wizard Welcome to the Add Printer Q Wizard This wizard helps you install a printer or make printer connections To continue click Next 13 17 CN2610 User s Manual Setting Up Printer 4 Select Local printer and click Next to continue Add Printer Wizard Local or Network Printer Is the printer attached to your computer If the prin
76. CN2610 as defined in etc hosts or its IP address 2048 the TCP port number Group01 of the printer port on the CN2610 accept printer Laser1 usr lib accept Laser1 Set Laser 1 to accept print request enable Laser1 enable printer Laser1 enable Laser print file to Laser1 lp dLaser1 file_name send print job to the CN2610 Repeat Repeat the above steps to set up another printer For printers in the same group it is not necessary to repeat every step 13 10 CN2610 User s Manual Setting Up Printer Setting up a SOLARIS X86 Host Steps SCO UNIX Command Description Set free the occupied Floppy disk etc init d volmgt stop Uncompress all programs tar dev fd0 Uncompress printer tar Z to printer tar xvf printer tar Z compile link make f sco_unix mak make printer node mknod dev iop1 p Create a unique pipe name for each printer group Since there are 16 groups of TCP port numbers from 2048 to 2063 you need to create 16 respective pipe names For example iop1 iop2 iop3 etc set it to printer chown Ip dev iop1 Change the pipe owner to 1p set rw chmod 600 dev iop Change access permission to 600 or TW set printer name usr lib lpadmin Redirect the printer spooler to write to pLaser1 v dev iop1 pipe iop1 Assumes the printer name is Laser1 execute asprint for Group
77. CN2610 Dual LAN Async Server User s Manual Fourth Edition July 2007 www moxa com product Moxa Technologies Co Ltd Tel 886 2 8919 1230 Fax 886 2 8919 1231 Web www moxa com MOXA Technical Support Worldwide support moxa com The Americas support usa moxa com CN2610 Dual LAN Async Server User s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Copyright 2007 Moxa Technologies Co Ltd All rights reserved Reproduction without permission is prohibited Trademarks MOXA is a registered trademark of the Moxa Group All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of MOXA MOXA provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose MOXA reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However MOXA assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might inc
78. CP alive check time Each item is described in detail below the figure Source IP address Destination IP addr Inactivity time Map keys lt CR LF gt to Authentication type TCP alive check time 9 4 CN2610 User s Manual Setting Up Reverse Terminal Setting Value Notes Necessity TCP port number Each of the CN2610 s serial ports is mapped to a TCP port To avoid conflicts with the TCP port numbers for CN251 s other serial ports use the default values 4001 for port 1 4002 for port 2 etc Optional Source IP IP address for Specify an IP address for this port for address the port application purposes If left blank the CN2610 will use its own IP address in which case you will need to specify different TCP port numbers for different serial ports Optional Destination IP IP address Assign a host IP address on the LAN for addr exclusive port access If left blank all hosts on the network will have access to this port Optional Map Keys CR LF CR LF When you enter the string lt CR LF gt the lt CR LF gt to CN2610 will determine whether to send lt CR gt lt LF gt or lt CR LF gt Optional Inactivity time 0 99 minutes Idle time before the port is disconnected automatically If set to 0 minutes the port will not disconnect Optional Authentication None local None Authentication is not required type server local Check the ID stored in the User_table defined
79. DAVE se E E EEEE E E E E EET 8 8 Restart aeae o aE E TA EN AE EE EEEE E EE AE 8 8 Setting Up Reverse Terminal sccccssseeeceeseeeeeesseeeeeeseseeeeeesseeeeeees 9 1 Accessing the Console Utility 00 cece eee E rE E E E EE S E Sa OE ae EE 9 2 Selecting the Application ich oneni a r E I aE E E E E N E 9 3 Configuring RTELNET Mode risos nnen ataa ER A E TER 9 4 Configuring the Serial POT Sei eatea reae pa a EAA EEEa EAE E RE iE apea 9 5 DAVE se EE E EEEE E E E E O EEE 9 7 Chapter 10 Chapter 11 Chapter 12 Chapter 13 Setting Up Terminal c 20nc naan ened tiinnainne nna 10 1 Accessing the Console Utility hverir eiaei i eE E E ea 10 2 Selecting the Applicaton ss aiareni nhn aa r e a i Rr 10 3 Configuring TERM_ASC Mode seseseeseseeeeessstsesresreresestsreteeretsreseststeesesrerretsessesesreerets 10 4 Configuring TERM_BIN Mode e eenean aneta oend a eaea Aeaee Aa Sa EEE ai 10 7 Configuring the Serial Ports suiii ooreen ei e REA i EE e rE EEA AREE 10 9 SAVE EE E EAE E S EEE E E E A egees 10 10 RESLALt ove chaste Soe A aie eh ed A eet GU I ae Se 10 11 Setting Up Multi host TTY ccccceeeeesssseeeeeeeeseeeeeeeeseeeeeneeeeeeeeeseneeeeeess 11 1 Accessing the Console Uta ty s cessecssnziseverecsctencteiievstaterecotn dace dinsneebeepusdewsbstosreseesi ae heteateeet 11 2 Selecting the Application 00 0 ce eeescsssecseesessecseesecseesecsaseecsaeceesecaeesecnevseesaeeeesaecaseaeeneeats 11 3 Configuring FIXTTY Moderens eases ee
80. E TI DRDAS Raw UDP PC redundant data 12 DRDAS Redundant COM PC redundant data iL DRDAS redundant data 7 3 CN2610 User s Manual Setting Up DRDAS 5 The only operation mode associated with this application is DRDAS which is selected automatically in the Mode column Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter POLE 01 Description more setting Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol Application DRDAS DRDAS DRDAS DRDAS DRDAS DRDAS DRDAS DRDAS Async Server Proprietary Protocol Async Server Proprietary Protocol Dual PC redundant data mode Async Server Proprietary Protocol Async Server Proprietary Protocol Configuring DRDAS Mode DRDAS mode supports a dual host redundant application structure on the redundant network 1 Move the cursor to the Description more setting column and then press Enter CNG LOS Be VAO Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting Omi 02 03 DRDAS DRDAS DRDAS Async Async Async server Server server Proprietary Proprietary Proprietary Protocol Protocol 04 05 06 07 08 DRDAS DRDAS DRDAS DRDAS DRDAS Async Server
81. Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 11 2 CN2610 User s Manual Setting Up Multi Host TTY Selecting the Application Open Port Menu gt Mode to configure the Multi host TTY application 1 From the MAIN MENU select Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 T Real COM Async Server Proprietary Protocol 02 T Real COM Async Server Proprietary Protocol 03 T Real COM Async Server Proprietary Pr
82. From the MAIN MENU select Restart isan ola oTe S A Restart Maieme Restart the whole system or selected async ports Enter select ESC previous menu 2 Select System and then press Enter to restart the system and terminate the Telnet session System SEZs Quit Restart the Async Server ESC back to menu Enter select Wetini LA Restart system will disconnect all ports and clear all status value Enter continue ESC Cancel 9 7 10 Setting Up Terminal In this chapter we describe the steps you should follow to configure the CN2610 as a Terminal Server The CN2610 provides Telnet and Rlogin protocols for terminals to establish connections with UNIX hosts Two terminal modes are supported ASCTJI terminal with up to 8 simultaneous sessions and Binary terminal with one session for one user Terminals can be connected directly to one of the CN2610 s RS 232 ports or connected from a remote site by using external modems The following topics are covered in this chapter Accessing the Console Utility Selecting the Application Configuring TERM_ASC Mode Configuring TERM_BIN Mode Configuring the Serial Ports Save Restart OOOCUUOCD CN2610 User s Manual Setting Up Terminal Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility i
83. IUS protocol If you have a RADIUS server you will need to enter the password in this field 2 16 CN2610 User s Manual Getting Started UDP port 1 1645 2 1812 There are two choices for RADIUS UDP port numbers The early deployment of RADIUS was done using port number 1645 but later on this conflicted with the RFC standard The officially assigned port number for RADIUS is now 1812 We recommend however that you use the old RADIUS server UDP port number of 1645 since many companies still use it Enable RADIUS accounting The default for this field is no If your RADIUS Server offers this function set it to yes SNMP community name The SNMP community name can be used to guarantee minimal security for SNMP communication Only SNMP stations with the same community name can access SNMP agents such as Async Server Choose a community name with no more than 16 ASCII characters The default name is public SNMP trap server IP address This field specifies the IP address of the SNMP trap server The CN2610 will report to the SNMP trap server each time it restarts You may leave this field blank if SNMP is not needed Ethernet IP forwarding The CN2610 can forward packets between different segments of a TCP IP network When enabled the CN2610 will use its Ethernet routing ability to identify which incoming packets should be forwarded Routing protocol The CN2610 supports RIP Routing Information Protocol versions 1 an
84. If your printer came with an installation disk click Have Disk If your printer is not listed consult your printer documentation for a compatible printer Manufacturers Printers Diconix Digital Epson Fujitsu GCC Generic xl Gostatner Generic IBM Graphics Spin Generic IBM Graphics Spin wide MS Publisher Color Printer MS Publisher Imagesetter Windows Update Have Disk E 8 Enter the printer s name and select yes if you wish to set this printer as the default printer Click Next to continue Add Printer Wizard Name Your Printer You must assign a name for this printer Supply a name for this printer Some programs do not support server and printer name combinations of more than 31 characters Printer name You Name here Do you want your Windows based programs to use this printer as the default printer Cc Yes o No lt Back Cancel 13 19 CN2610 User s Manual Setting Up Printer 9 Select Shared when prompted with questions asking if the printer is to be shared or not and then enter the name of the shared printer Click Next to continue Add Printer Wizard Printer Sharing You can share this printer with other network users 10 You will need to reboot Windows 2000 to enable the printer you just added When asked if you want to print a test page select No Click Next to continue Add Printer Wizard a Print Test Page To confirm that the
85. M Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Async Server Proprietary Protocol 05 NT Real COM Async Server Proprietary Protocol 06 Raw UDP Pure raw data UDP mode oN NT Real COM Async Server Proprietary Protocol J 2 The pop up selector contains input display fields for serial to LAN and LAN to serial parameters Local Listen Port Delimiter 1 Hex Delimiter 2 Hex and Force transmit ms Each item is described in detail below the figure serial to LAN Deste TE addr aL Deste IP addr z Desti IP adar 3 Dest IP addr a LAN to serial Sro IP adar T SieSe Ie A 7 Sieci abe exclola S See s ie Adar 4 Local Listen Port Delimiter 1 Hex Delimiter 2 Hex Force transmit ms 6 4 CN2610 User s Manual Setting Up Raw UDP Setting Value Notes Necessity Dest IP Begin x x x x Defines 1 to 4 groups of IP addresses UDP 1 Required address End y y y y packets will be sent through UDP port Port 2 3 4 are 1 2 3 4 Port 1 to 65535 to the range of IP addresses from the Begin Optional IP address to the End IP address Src IP Begin x x x x Defines IP addresses that will be allowed 1 Required address End y y y y to transmit UDP packets to the CN2610 s 2 3 4 are 1 2 3 4 Port 1 65535 Ethernet port UDP packets from IP Optional addresses in the range from Begin IP address to End IP address will
86. M Multiplex Server Proprierary Protoce Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol 07 Real COM Printer Server Proprietary Protocol 08 Real COM Me OS E ry Server Proprietary Protocol NT Real COM Raw UDP Redundant COM 14 7 CN2610 User s Manual Setting Up Multiplexor 5 The Multiplex application supports two operation modes RTELNET and TERM _BIN RTELNET mode is selected by default For the Device CN2610 select TERM_BIN mode CM 6 Se NH9 V20 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Reverse Telnet mode NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting Ok NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Async Server Proprietary Protocol 05 NT Real C
87. Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection 4 Press ESC to return to the PORT MENU Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save CAELOS S VAO ip obo an eso ue A Os oE O o USer table Roti Examine modify async server basic configuration Enter select ESC previous menu Warning My You had modified the configuration without saving Would you save it now Yes You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel CNZG1O 6 109 v2 0 Server Port seTting Uitliey Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select 14 12 CN2610 User s Manual Setting Up Multiplexor Restart From the MAIN MENU select Restart CN2610 8_19 lant Sane oh a ET Uh oni oe ME Y W emma Restart Mipene Restart the whole system or selected async ports Enter select ESC previous menu Select System and then press Enter to restart the system and terminate the Telnet session CNZGILO 5 20 System zene Quit Restart the Async Ser
88. NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address Te 21x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 x Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter A Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below fa Telnet 192 168 127 254 CWZOLO S LE V20 Server SELI a Ee S ANE Ooms il A C or a OI E Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Ese Bey Shortcut Key Capitalized letter of the word 14 2 CN2610 User s Manual Setting Up Multiplexor Selecting the Application The Multiplex application uses two Async Servers One of the servers called the host CN2610 is attached to a host with a multi port serial board and mutiple serial lines The other server called th
89. OM Async Server Proprietary Protocol 06 Multiplex Reverse Telnet mode NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol 07 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application Description more setting 01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM t rver Proprietary Protocol 05 NT Real COM RTELNET rver Proprietary Protocol 06 Multiplex I ITERM_BIN PORE mode OF Real COM t rver Proprietary Protocol 08 Real COM Async Server Proprietary Protocol NT NT 14 8 CN2610 User s Manual Setting Up Multiplexor NOTE 8 The next step is to configure the TERM_BIN parameters C2 610 2 VOO OOOO O Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Async Server Proprietary Protocol 05 NT Real COM Async Server Proprietary Protocol 06 Multiplex Binary Terminal mode 1 session 07 Real COM Async Server Proprietary Protocol 08 Real COM Async Server Proprietary Protocol
90. OM Multiplex 07 Real COM Printer 08 Real COM Mudkiza SHO sit li NT Real COM DRDAS Redundant COM Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol Server Proprietary Protocol 6 3 CN2610 User s Manual Setting Up Raw UDP 5 The only operation mode associated with this application is RAW UDP which is selected automatically in the Mode column CZE TO P 19 V20 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real Async Server Proprietary Protocol Real ASPE Async Server Proprietary Protocol Real COM ASPP Async Server Proprietary Protocol Real COM ASPP Async Server Proprietary Protocol Real COM ASPP Async Server Proprietary Protocol RAW UDP Pure raw data UDP mode NT Real COM ASPP Async Server Proprietary Protocol Configuring RAW UDP Mode 1 Move the cursor to the Description more setting column and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application Description more setting ual NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real CO
91. P address Ethernet speed and Ethernet address Each item is described in detail below CEOE 8 V Info JRREE Adv Host_table Route_table User_table Quit Examine modify the Ethernet LAN port setting ESC back to menu Enter select Ethernet LAN port 1 DHCP client Async server IP address Async server IP netmask Default gateway IP address Ethernet speed 10Mbps Ethernet address OO SSH0 8 iarts s 00 8 ONO 8 0 5 Ethernet LAN port 2 DHCP client Disable Async server IP address LOZ 168 25 254 Async server IP netmask ye sie cere ers yee Default gateway IP address Ethernet speed Ethernet address 00 90 E8 00 00 06 Ethernet LAN port 1 or 2 DHCP client When DHCP is enabled the CN2610 will request an available IP address and Netmask over the network from the DHCP Server and the DHCP Server will assign an available IP address and Netmask to CN2610 LAN If an IP address is not available CN2610 LANI will use the current IP address but will continue sending requests to the DHCP Server Async server IP address This field MUST contain an IP address unique to the network The IP address is written using the notation ddd ddd ddd ddd in which each ddd is a nonnegative decimal number strictly less than 256 i e an 8 bit integer The default value is 192 168 127 254 Async server IP netmask A netmask is used to isolate a group of computers to the same subnet When a packet is sent out over th
92. P parameters 12 9 CN2610 User s Manual Setting Up Dial in Out 6 The pop up selector contains input display fields for Quit key Auto link protocol Link by input IP Auto login prompt Terminal type Inactivity time Authentication type and TCP alive check time Each item is described in detail below the figure Quit key AULO lank prokoce Telnet TCP port Primary Host LP Link by input IP Secondary host IP Auto login prompt a kexeptiag Password prompt assword Login user name Login password Terminal type amp leans Inactivity time 0 minuwies Authentication type none l TCP alive check time f 0 minutes Setting Value Notes Necessity Quit Key E Defines the Quit key used to disconnect Optional the link between the current terminal session and the remote host It may be left blank for binary communication Auto link protocol None Telnet None Do not connect to the host Optional Rlogin automatically Telnet Connects to the host automatically by Telnet Rlogin Connects to the host automatically by Rlogin Telnet TCP port 23 Enter a number or leave the space blank Optional If not specified then by default port 23 is used If you want to use Telnet without a TCP port number set this option to 23 Primary host IP IP address or If specified designates a permanent Optional the name host to which the terminal will always be defined in the connected Host t
93. PD PRN Mode 1 Move the cursor to the Mode column for the port and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Async Server Proprietary Protocol Ge NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Async Server Proprietary Protocol 05 NT Real COM Async Server Proprietary Protocol 06 Printer Raw serial port printer mode NT Real COM Async Server Proprietary Protocol 2 Select LPD PRN and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM f gt Server Proprietary Protocol 03 NT Real COM amp gt Server Proprietary Protocol 04 NT Real COM Proprietary Protocol 05 NT Real COM Proprietary Protocol 06 Printer al port printer mode 07 NT Real COM rver Proprietary Protocol NT Real COM fi gt Server Proprietary Protocol 3 ENACO TO AL Mode Line mOdem Welcome _ MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 Real COM ASPP Async Server Proprietary Protocol 02 Real COM ASPP Async Server
94. Proprietary Protocol Async Server Proprietary Protocol Dual PC redundant data mode Async Server Proprietary Protocol Async Server Proprietary Protocol Protocol 2 The pop up selector contains input display fields for TCP data port TCP command port Primary IP addr Backup 1 IP addr Backup 2 IP addr Backup 3 IP addr and TCP alive check time Each item is described in detail below the figure TOP data p rt TCP command port Pranacy HS aele Backup 1 IP addr Backup 2 IP addr Backup 3 IP addr TCP alive check time Every CN2610 port has the ability to connect to 4 different IP addresses at the same time The Primary IP addr must be configured as the IP address of the primary host controlling the serial port and the Backup n IP addr must be configured as the IP address of the redundant host When the primary host disconnects for an unknown reason the user s program running on backup hosts must use the switching library to allow backup IPs take over In this way the CN2610 s control ability and the data flow will be transferred to the backup host In the meantime the primary host s dual Ethernet ports and those of the backup host will receive the 7 4 CN2610 User s Manual Setting Up DRDAS same uploaded serial data In the specified period of time if one of the secondary IPs tries to send commands to the serial device the commands will be discarded once they reach the CN2610 since
95. RAW UDP Mode QO Configuring the Serial Ports Save Restart CN2610 User s Manual Setting Up Raw UDP Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 6 2 CN2610 User s Manual Setting Up Raw UDP Selecting the Application Open Port Menu gt Mode to configure the Raw UDP application 1 From the MAIN MENU select P
96. Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select Restart 1 From the MAIN MENU select Restart CN OE S V Sesan a ola oTe S A Restart Maipeme Restart the whole system or selected async ports Enter select ESC previous menu 2 20 CN2610 User s Manual Getting Started 2 Select System and then press Enter to restart the system and terminate the Telnet session 102 61 0 2 7 OOOO OO System Bzenae Quit Restart the Async Server ESC back to menu Enter select Warning ft Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 2 21 3 Knowing Your Application This chapter discusses a variety of applications for the CN2610 Async Server Refer to the diagrams in each section to see which application most closely matches your own Determining which application you should choose will save time configuring both the hardware and software The CN2610 is an Async Server that can support simultaneously different operation modes for different serial ports The examples in this chapter explain each operation mode in detail You can create a wide variety of applications by using different combinations of operation modes on the same Async Server NOTE Each section title consists of an application name that uses terminology common to our industry followed in parentheses by the application name used in the CN2610 s console uti
97. Run Upgrade exe from the CN2610 CD ain x Server Tool Help 225 2 ate Upgrade marell IP patter MAC address CN2510 8 563 CN2510 8 92 00 90 E8 00 2 Select the CN2610 server by clicking the gt button on the toolbar If the CN2610 server is at a remote site use ws to add it to the list Upgrade NPort Server x Enter the file to upgrade Server Name CN2510 8_5631 IP address 192 168 127 254 Serial No 5631 m 16 8 CN2610 User s Manual Administrative Utilities 3 Specify the new firmware file used to upgrade Click OK to start NPort Server Upgrade xi Server Name CN2510 8_5631 Serial No 5631 Server IP address 192 168 127 254 Downloading 30 BANAKA x 4 When the Download ok window appears click OK NPort Server firmware upgrade utility xj A Download ok Console Terminal Upgrade 1 Run Start gt Programs gt PComm Terminal Emulator If you cannot find the software on your computer install PComm Lite from the CN2610 CD and then run the program GH PComm Lite 2000 XP Ver 1 2 Library Programming Guide Library Reference ay PComm Diagnostic a PComm Monitor E3 PComm Terminal Emulator 2 Use an RJ45 DB9 female cable to connect to the console port and then turn on the CN2610 Start the PComm Terminal program and then open a new connection E5 PComm Terminal Emulator Profile Port Manager Help HJA dhok ea 28 16 9 CN2610 U
98. S File Action Yiew Help gt S 2 9 ernet Authenticati a E Rem 2 a Rem New amp Conr Refresh Help Welcome to Internet Authentication Service Use Internet Authentication Service 145 to authenticate authorize and account for dial up VPN wireless and Ethernet connections to your network You can also configure IAS to forward authentication requests to any access server that is compatible with Remote Authentication Dial In User Service RADIUS To configure IAS to read the remote access properties of user accounts in Active Directory on the Action menu click Register Server in Active Directory For more information about setting up 145 deployment scenarios and troubleshooting see Help New dient 5 Select NEW RADIUS Client to add a new RADIUS client You will then be able to start using this function B 17 C SNMP Agent with MIB II Simple Network Management Protocol agent software is built into the CN2610 The software supports cold warm start trap line up down trap and RFC 1213 MIB II The following table lists the standard MIB II groups as well as the variable implementations for the CN2610 Supported SNMP variables System MIB Interfaces MIB IP MIB ICMP MIB SysDescr itNumber ipForwarding IcmpInMsgs SysObjectID __ ifIndex ipDefaultTTL Icm
99. Setting Up Multi Host TTY Using Fixed TTY Driver Starting Fixed TTY Driver Once you have completed the above settings you can start Follow the steps given below to ensure that driver is running correctly See if the entries added to moxattyd cf are correct Run init qor reboot your system to start the moxatt yd daemon If you see that moxattyd is running on your system then Fixed TTY driver has been successfully started Stopping Fixed TTY Driver If for any reason you need to stop the moxattyd daemon the two methods listed below allow you to stop the moxattyd daemon process 1 Remove entries related to moxattyd daemon in etc inittab and execute init qor reboot your system or 2 Replace respawn with off in entries related to moxattyd daemon in etc inittab and execute init q or reboot your system For instance ts 2 off usr etc moxattyd moxattyd 11 10 12 Setting Up Dialin out In this chapter we describe the steps required to configure the CN2610 as a Dial in out Access Server Dial in Access allows remote users to access the LAN whereas Dial out Access allows LAN hosts to establish connections to other sites The following topics are covered in this chapter Accessing the Console Utility Selecting the Application Configuring PPPD PPP Mode Configuring SLIPD SLIP Mode Configuring Dynamic Mode Configuring the Serial Ports Configuring Modem Initialization Optional Welcome Message Configuring Optiona
100. The MAIN MENU is shown below NOTE Click Edit gt Font to choose a different font for the MAIN MENU Ei PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a BA alele 32 E COM1 115200 None 8 1 T100 Ch CNZS10 8 5631 V2 0 seTting sAve Utility Restart Exit 2 12 CN2610 User s Manual Getting Started Configuring the CN2610 The Server Menu In this section we describe both basic and advanced configuration tasks We use the Telnet interface to illustrate the Serial Console interface is the same Server Configuration Info 1 From the MAIN MENU use the arrow keys to select Server and then press Enter CN2610 8_19 v2 0 Server AI d Ee mary 4 4 Eee O hoe eh ae thot ba op oe Examine modify async server node table configuration Enter select ESC previous menu 2 From the SERVER MENU select Info and then press Enter ENZIGHO SORES WO Adv Host_table Route_table User_table Quit Examine modify async server basic configuration Enter select ESC previous menu 3 The Info page contains input display fields for name location serial number Domain server 1 2 IP address WINS function disable WINS server IP address and Console password Each item is described in detail below CNZIGHOS S MIOYO Info ERa Host_table Route_table User_table Quit Examine modify async server basic configuration ESC back to menu Enter selec
101. Unix Hosts gt Setting up a SCO Unix Host gt Setting up a SOLARIS X86 Host gt Setting up a LINUX Host QO Setting up Windows Hosts gt Setting up a Windows NT Host gt Setting up a Windows 2000 Host OOOCUCOCOD CN2610 User s Manual Setting Up Printer Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 13 2 CN2610 User
102. Unix host s network printer function via RAW mode and assign a specific IP address and TCP port number to specify the printer s location You can also connect to the printer via LPD mode when LPD protocol is needed to operate the printer Refer to Chapter 12 for detailed information and configuration instructions 3 12 CN2610 User s Manual Knowing Your Application Multiplexor Access Multiplex 4 IBM workstation Bw l with multiport board z PS g CN2610 TCP IP Router PA TCP IP CN2610 If are using a multiport serial board installed in a UNIX host but wish to extend the device control range without dismantling the host you can accomplish this with the CN2610 Multiplex and De multiplex solutions use the CN2610 s RTelnet and terminal modes eliminating the need to modify existing software The CN2610 acts like a converter by extending the communication distance The CN2610s work in pairs over the network to overcome the short communication distance limitation imposed by serial connections See Chapter 13 for detailed configuration instructions NOTE This mode does not allow copying the status of control signals to devices at a remote site 3 13 4 Setting Up Windows Real COM Linux Real TTY Unix Fixed TTY The CN2610 supports Real COM TTY drivers for Windows and Linux allowing the CN2610 s serial ports to be recognized as Real COM ports by the Windows operating system or Real TTY
103. User s Manual Administrative Utilities 6 Ports that have been activated will appear in black 4 NPort Windows Driver Manager J J fal ell Undo 192 1 951 967 Port 192 168 34 111 _952 968 Port3 COM22 192 168 34 111 953 969 Port4 LEN 192 168 34 111 954 970 Port5 192 168 34 111 192 168 34 111 192 168 34 111 192 168 34 111 192 168 34 111 192 168 34 111 192 168 34 111 192 168 34 111 R 192 168 34 111 m 192 168 34 111 192 168 34 111 To re configure the settings for a particular serial port on the CN2610 select the row corresponding to the desired port and then click the Settings icon 4 COM Port Setting COM3 current fin use Y M Mapping IP address Mapping IP address 16 22 CN2610 User s Manual Administrative Utilities 8 On the Basic Settings page use the COM Number drop down list to select a COM number to be assigned to the CN2610 s serial port that is being configured Select the Auto Enumerating COM Number for Selected Ports option to assign available COM numbers automatically in sequence to selected serial ports Note that ports that are in use will be labeled accordingly comport setting STE Port Number 2 Port s are Selected Basic Settings Advanced Settings Serial Parameters Security J Auto Enumerating COM Number for Select
104. V20 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real Async Server Proprietary Protocol NT Real Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Reverse Telnet mode NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NOTE Reverse Telnet or RTELNET supports the Telnet program used by Ethernet hosts to login to serial hosts Ethernet hosts recognize serial ports by the specified source IP address or by the TCP port number followed by the CN2610 s IP address 6 Move the cursor to the Description more setting column and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting Omi T Real COM il gt Server Proprietary Protocol 02 T Real COM gt Server Proprietary Protocol 03 T Real COM Server Proprietary Protocol 04 T Real COM 1 gt Server Proprietary Protocol T Real COM ASPP gt Server Proprietary Protocol Multiplex RIELNET NT Real COM ASPP Async Server Proprietary Protocol NT Real COM ASPP il Async Server Proprietary Protocol N N N N N 7 The pop up selecto
105. a gateway host with a router can send its entire routing table which lists all the other hosts it knows about to its closest neighbor host every 30 seconds The neighbor host in turn will pass this information on to its closest neighbor and so on until all hosts within the network have the same routing path information This state is known as network convergence RIP uses a hop count as a way of determining network distance Other protocols use more sophisticated algorithms that also include timing After receiving a packet headed for a specific destination a network host with a router uses the routing table information to determine the next host to route the packet to RIP is considered an effective solution for small homogeneous networks For larger more complicated networks transmitting the entire routing table every 30 seconds can bog down the network with a lot of extra traffic RIP 2 is an extension of RIP Its purpose is to expand the amount of useful information contained in RIP packets and to add security elements RIP version 2 recently became the standard version of RIP and the original RIP is no longer in use Configuring RIP Open Server Menu gt Adv to configure Dynamic routing 1 From the MAIN MENU select Server and then press Enter CWZ EMOS 18 7200 Server SELIA oe mimn 7 0 4 San Oh ons il Ws oA 5 1 9 ok al OID Examine modify async server node table configuration Enter select ESC previous menu 2
106. able Link by input IP Enable For users to enter the connection IP Optional Disable address manually Secondary host IP IP address or If specified designates a secondary Optional the name permanent host to which the terminal defined in the will be connected Host table Auto login prompt ogin Send ID information when this prompt is Optional received Password prompt assword Send Password information when this Optional prompt is received Login user name Login ID Optional Login password Login Password Optional Terminal type ansi Terminal type for outgoing connection Optional 12 10 CN2610 User s Manual Setting Up Dial in Out Setting Value Notes Necessity Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect Authentication None local None Authentication is not required Optional type server local Check the ID stored in the User_table defined under the SERVER MENU Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information TCP alive check 0 99 minutes The time period the CN2610 waits before Optional time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 7 To configure the PPPD
107. al modes with up to 8 Telnet and Rlogin sessions Point to Point Protocol PPP and PPPD Serial Line Internet Protocols SLIP and SLIPD Dynamic auto recognition of Terminal SLIP or PPP Dial on demand Dial out Remote serial or parallel printing RLP CN2610 Async Server Proprietary Protocol ASPP for TCP IP socket programming RAW mode for transparent data transmission Reverse Telnet SNMP Agent for network management Network protocols TCP IP UDP ICMP NetBEUI DHCP Application protocols Telnet Rlogin Rtelnet RAW TCP RAW UDP RCP WINS DRDAS LPD DNS Multi Host Security protocols RADIUS Dial back PAP CHAP Local user password Real COM port drivers Windows 95 98 ME NT 2000 XP 2003 XP x64 2003 x64 Vista x64 Real TTY drivers Linux kernels 2 2 x 2 4 x 2 6 x SCO Unix SCO OpenServer 5 SCO OpenServer 6 UnixWare 7 S VR4 2 QNX 4 25 QNX 6 Solaris 10 FreeBSD 5 FreeBSD 6 Static Routing RIP III protocols Windows like administrative CONSOLE utility from a fixed console port or by Telnet from a networked host Password protection and extensive user verification functions Easy firmware upgrade via Flash ROM Package Checklist CN2610 dual LAN async servers are shipped with the following items CN2610 Dual LAN Async Server AC power cord Documentation and Software CD ROM Quick Installation Guide English and Simplified Chinese versions RJ45 Loopback Tester Product Warranty Booklet Rackmount Kit inclu
108. ally by Rlogin 10 5 CN2610 User s Manual Setting Up Terminal 5 or not If no response is received the CN2610 will reset the port and terminate the connection Setting Value Notes Necessity Telnet TCP port 23 Enter a number or leave the space blank Optional If not specified then by default port 23 is used If you want to use Telnet without a TCP port number set this option to 23 Primary host IP IP address or If specified designates a permanent Optional the name host to which the terminal will always be defined in the connected Host table Link by input IP Enable For users to enter the connection IP Optional Disable address manually Secondary host IP IP address or If specified designates a secondary Optional the name permanent host to which the terminal defined in the will be connected Host table Auto login prompt ogin Send ID information when this prompt is Optional received Password prompt assword Send Password information when this Optional prompt is received Login user name Login ID Optional Login password Login Password Optional Terminal type ansi Terminal type for outgoing connection Optional Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect Authentication None local None Authentication is not required Optional type
109. and then click Next jie PComm Lite 2000 XP er 1 2 License Agreement End User License Agreement Before installing the PComm Lite you must agree to Moxa s End User Product License Agreement Please read through this license agreement carefully If you do not agree to them please DO NOT install the software Subject to the following terms and conditions Moxa Technologies Co Ltd Moxa grants to you User a ePxclusive license to use the enciosed sanftmari CN2610 User s Manual Getting Started 4 Select a directory in which to install the CN2610 Utility and then click Next i PComm Lite 2000 XP er 1 2 Select Installation Folder 5 Click Next to continue iz PComm Lite 2000 XP Yer 1 2 Confirm Installation 2 9 CN2610 User s Manual Getting Started 6 Wait while the PComm Lite software is installed j PComm Lite 2000 XP er 1 2 Installing PComm Lite 2000 XP Ver 1 2 Erevious 7 Click Close jie PComm Lite 2000 XP er 1 2 Installation Complete Parcel Previous CN2610 User s Manual Getting Started 8 When the installation is complete select Start gt Programs gt PComm Terminal Emulator to run PComm Terminal Emulator fH PComm Lite 2000 XP Ver 1 2 2 Library Programming Guide Library Reference ay PComm Diagnostic af PComm Monitor EA PComm Terminal Emulator 9 Use an RJ45 to DB25 female cable to conne
110. assword Optional Terminal type ansi Terminal type for outgoing connection Optional Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect Authentication None local None Authentication is not required Optional type server local Check the ID stored in the User_table defined under the SERVER MENU Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information TCP alive check 0 99 minutes The time period the CN2610 waits before Optional time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 14 10 CN2610 User s Manual Setting Up Multiplexor 11 Repeat the previous steps for ports 5 7 and 8 C2 6 1 0 rrr 2O O O O OOOO Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting om Real COM Async Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Real COM Async Server Proprietary Protocol 04 Real COM Async Server Proprietary Protocol 05 Multiplex Binary Terminal mode 1 session 06 Multiplex Binary Terminal mode 1 session 07 Multiplex Binary Terminal mode 1 session 08 Multiplex Binary Terminal mode 1 session Configuring the Serial Ports O
111. at still requires some explanation is how to edit the configurable options In fact you will only encounter two types of configurable options E 2 CN2610 User s Manual Service Information The first type involves entering numbers such as IP addresses Netmasks etc In this case you change the number one digit at a time The up cursor A is used to decrease the highlighted digit the down cursor V is used to increase the highlighted digit and the sel button is used to move to the next digit When the last digit has been changed pressing sel simply enters the number into the CN2610 s memory The second type of configurable option is when there are only a small number of options from which to choose although only one option will be visible at a time Consider the Parity attribute under Serial set as an example Follow the tree graph to arrive at the following Parity screen The first option None is displayed with a down arrow all the way to the right This is an indication that there are other options from which to choose P a r i t y N o n e v Press the down cursor button once to see Odd as the second option P a ia i y o d d 4 Press the down cursor button again to see Even as the third option P a i y E v e n v Press the down cursor button again to see Space as the fourth option P a r i y fi S p a Cc e 4 Press the down cursor button yet again to see the last
112. b terminal It sends all characters pressed on the keyboard to a remote connection and then echoes the data to the screen 3 This program sends r as r n and n as r n 4 All CN2610 ASPP functions are defined in the file as h 5 The program works on Windows 9x NT 2000 XP 2003 as a dumb terminal After completing the connection to the CN2610 the serial port will send all characters pressed on the keyboard to the remote connection and then echo the data to the screen Then the program will send 12345 to Async Server s port 1 at 19200 bps baudrate and read back any data on it 6 Setting Up Raw UDP UDP is a non connection oriented data transmission method By circumventing TCP s handshaking process UDP gains the advantages of fast transmission speed and high transmission efficiency The disadvantage is that UDP is unable to guarantee data integrity since UDP does not re assemble out of order packets or retransmit packets when data is missing UDP is an ideal transmission method if you need fast data transmission and upper layer application software is given the task of checking data for transmission errors The CN2610 s UDP mode supports 4 configurable groups of IP addresses allowing data to be broadcast over the network to one or more groups of IP addresses The following topics are covered in this chapter UO Accessing the Console Utility QO Selecting the Application Configuring
113. be accepted through UDP port Port Local 1 65535 The UDP port that the CN2610 listens to and Required Listen that other devices must use to contact the Port CN2610 The default is blank Be sure to choose a Local Listen Port number that does not conflict with the Local Listen Port for the CN2610 s other serial ports Delimiter 00 FF Once the CN2610 receives delimiters Optional 1 2 through its serial port or the amount of lt Hex gt data received exceeds 1K it immediately packs all data currently in its buffer and sends it out the CN2610 s Ethernet port Note Delimiter 2 is optional If left blank then Delimiter 1 alone trips clearing of the buffer Force 0 65535 0 Disable this function Optional transmit 1 to 65535 Forces the CN2610 to try to lt ms gt pack serial data received during the specified time into the same data frame via UDP mode The optimal Force Transmit timeout depends on the application but it must be at least as large as the time required to transmit one character for the specified baudrate For example assume that the serial port is set to 1200 bps 8 data bits 1 stop bit and none for parity In this case the total number of bits required to send a character is 10 bits and the time required to transfer one character is 10 bits 1200 bits s 1000 ms s 8 3 ms Therefore you should set the Force Transmit timeout to be greater than 8 3 ms The Force Transmit timeout is
114. c Server Proprietary ASPP Async Server Proprietary ASPP Async Server Proprietary Protocol Protocol ASPP Async Server Proprietary Protocol Protocol ASPP Async Server Proprietary Protocol SLIP Serial Line Internet Protocol ASPP Async Server Proprietary Protocol ASPP Async Server Proprietary Protocol 4 The pop up selector contains input display fields for Destination IP addr Source IP address IP netmask TCP IP compression Inactivity time Link quality report Outgoing PAP ID PAP password and Incoming PAP check Each item is described in detail below the figure Destination IP addr Source IP address IP netmask TCP IP compression minutes Inactivity time EA Link quality report Outgoing PAP ID PAP password Incoming PAP check Setting Value Notes Necessity Destination IP IP address for the Assign an IP address for the remote user Required addr remote Dial in Dial out user Source IP IP address for the The CN2610 will automatically assign Optional address port an IP address for the port We recommend leaving this space blank IP netmask IP netmask The CN2610 automatically assigns the Optional netmask 255 255 255 255 We recommend leaving this space blank TCP IP Yes No Depends on whether the remote user s Optional compression application requests compression Inactivity time 0 99 minutes Idle time before the port is disconnec
115. c Server Proprietary Protocol 03 NT Real COM ASPP Async Server Proprietary Protocol 04 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM Async Server Proprietary Protocol Dialin out Auto Term SLIP PPP identification NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode DYNAMIC on more setting 01 NT Real COM ASPP PPP xver Proprietary Protocol 02 NT Real COM ASPP PPPD rver Proprietary Protocol 03 NT Real COM ASPP rver Proprietary Protocol 04 NT Real COM ASPP rver Proprietary Protocol 05 NT Real COM ASPP rver Proprietary Protocol 06 Dialin out DYNAMIC Auto Term SLIP PPP identification 07 NT Real COM ASPP Async Server Proprietary Protocol 08 NT Real COM ASPP Async Server Proprietary Protocol 12 6 CN2610 User s Manual Setting Up Dial in Out 3 Move the cursor to the Description more setting column and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports CN2610 8 ESC back to menu Enter select Mode ASPP Port Application 01 NT Real COM 02 NT Real COM 03 NT Real COM 04 NT Real COM 05 NT Real COM 06 Dialin out 07 NT Real COM 08 NT Real COM Description more setting Asyn
116. c Server Proprietary Protocol 06 Terminal IE Insc II Terminal mode 8 sessions J Async Server Proprietary Protocol Async Server Proprietary Protocol 07 08 Real COM Real COM NT NT 4 The pop up selector contains input display fields for Key Mapping Auto link protocol Link by input IP Auto login prompt Terminal type Inactivity time Authentication type and TCP alive check time Each item is described in detail below the figure Key Mapping Max Sessions Change Session Break Interrupt Auto link protocol none Telnet TCP port eS 25 Primary Host LP bank by anput IP Disable Secondary host IP Auto login prompt amp oejaticns Password prompt assword Login user name Login password Terminal type eee Inactivity time a 0 minutes Authentication type amp Lkevecik i TCP alive check 0 minutes Setting Value Notes Necessity Key Mapping Max Sessions 1 8 Configure the max number of sessions Optional Change Session AT Hot key for changing sessions Optional Quit AE Hot key for quitting a session Optional Erase line Hot key for erase line Optional Break Hot key for sending Telnet break signal Optional Interrupt Hot key for program termination Optional Auto link protocol None Telnet None Do not connect to the host Optional Rlogin automatically Telnet Connects to the host automatically by Telnet Rlogin Connects to the host automatic
117. ck to see if the RADIUS Server s IP is correct E g set up one port as Rtelnet telnet the CN2610 s TCP port from radius and then telnet the CN2610 s console and check the Monitor line status Check to see if the remote IP address matches the radius IP address you set in the A 6 CN2610 User s Manual Troubleshooting CN2610 Question Why cannot I compile radius software on a system running Linux Red hat 5 0 Solutions Take the following steps if you compiled RADIUS2 3 on Red hat 5 0 or above 1 Save makefile SCO as a file named makefile LINUX and then modify the content as follows make file for LINUX LIBS lcrypt include Makefile Add two similar line to the shell program mk_radius at read_os 1 For example they might appear as follows read_os case ans in 1 clear mk_src echo enter lib directory cd lib echo compiling source program make cd echo linking program make f Makefile LINUX A 7 B RADIUS Server Managing dispersed serial lines and modem pools for large numbers of users can create the need for significant administrative support Since modem pools are a link to the outside world they require careful attention to security authorization and accounting This can best be achieved by managing a single database of users allowing for authentication verifying user name and password as well as configuring
118. click Next to continue Add Hardware Wizard Is the hardware connected CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 6 Select Add a new hardware device and then click Next to continue Add Hardware Wizard The following hardware is already installed on your computer 3 MOXA Communication Port 5 COM J MOXA Communication Port 6 COM8 wo MOXA Communication Port 7 COM3 J MOXA Communication Port 8 COM10 WF Intellr Pentium n lll processor evice 7 Select Install the hardware that I manually select from a list Advanced to install the hardware and then click Next to continue Add Hardware Wizard The wizard can help you install other hardware CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 8 The window that opens next will ask you to select the type of hardware you are installing Select Multi port serial adapters and then click Next to continue Add Hardware Wizard From the list below select the type of hardware you are installing N S If you do not see the hardware category you want click Show All Devices Common hardware types S IEEE 1394 Bus host controllers SB Imaging devices A Infrared devices bo Modems Multi port serial adapters E9 Network adapters D NT Apm Legacy Support PCMCIA adapters IB PCMICIA and Flach mamon davieas zl cme 9 The window that opens next will ask you to s
119. ct Upgrade and then press Enter E3 PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a alaj alleas 32 E COM1 115200 None 8 1 T100 10 x m CENE CN2510 8_5631 V2 0 fore Ping Monitor Diagnostic Upgrade operational system progr evious menu 16 11 CN2610 User s Manual Administrative Utilities 3 Select Console port using XMODEM for Upgrade type and then press Ctrl U to start PComm Terminal Emulator COM1 115200 Non Profile Edit Port Manager Window Help a BIA elhas s28 0M1 115200 None 8 ct CN2510 8_5631 V2 0 iTr Ping Monitor Diagnostic W FECG RTS Upgrade operational system program back to menu Enter Upgrade via Host name IP address File name User name Press CTRL U to start 4 When you see Start loading file near the bottom of the screen click the Port Manager menu EJ PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a BIA elhel S2 E com1 115200 None 8 1 vT100 om BE 8 CN2510 8_5631 V 0 ion RTS Upgrade via C e port using XMODEM Host name IP address File name User name Press CTRL U to start Start loading file StateOPEN BE m m m Ready 16 12 CN2610 User s Manual Administrative Utilities a 6 Select Port Manager gt File Transfer from the menu bar EA PComm Terminal Fmulator COM1 115200 None 8 1
120. ct to the CN2610 console port Start PComm Terminal and then click the left most icon to open a new connection 1 Pe Terminal Emulator Profile Port Manager Help ajala caes ze 10 Click the Communication Parameter tab select the COM port COM2 in this example for console connection 115200 for Baudrate 8 for Data Bits None for Parity and 1 for Stop Bits Property x Communication Parameter Terminal File Transfer Capturing COM Options Ports Baud Rate s20 z Data Bits b H Parity None xi Stop Bits ho H Flow Control I RTS CTS Output State DTR ON OFF RTS ON C OFF I XON XOFF 2 11 CN2610 User s Manual Getting Started 11 Click the Terminal tab and select VT100 for terminal type Press Enter to confirm Propere Communication Parameter Terminal File Transfer Capturing Terminal Type X Dumb Terminal Option r Transmit F Local Echo Send Enter Key As CR LF r Receive CR Translation No Changed z LF Translation No Changed z Cancel 12 Type 1 to select ansi VT100 terminal type and then press Enter to open the MAIN MENU E PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a BFA alele 32 E COM1 115200 None 8 1 T100 RTS JAsync Server CN2510 8 Console terminal type l ansi vtl00 Z2 vt5 1l 13
121. d 2 a widely used protocol specifying how routers exchange routing table information When RIP is activated routers or CN2610s periodically exchange entire routing tables TCP retransmission timeout This is the amount of time the CN2610 waits to retransmit after a transmission failure occurs SIO data transfer timeout This is the amount of time in milliseconds the CN2610 waits to send serial data to the Ethernet Use a shorter timeout to improve efficiency Server Configuration Host_table 1 From the MAIN MENU use the arrow keys to select Server and then press Enter CN ENO E MS VAA Server EEZ aeeoe S N A E a E Examine modify async server node table configuration Enter select ESC previous menu CN2610 User s Manual Getting Started 2 From the SERVER MENU select Host_table and then press Enter Iiton CA HOSt table WE C ine oE ES am er o EO Examine modify async server basic configuration Enter select ESC previous menu 3 The Host_table contains frequently accessed host names and their corresponding IP addresses Adding entries to this table gives you the advantage of being able to refer to a host by name instead of by IP address The host table can hold up to 16 Host name Host IP address entries The Host_table page contains input display fields for Entry Host name and Host IP address CNG LOG MS V2 A Io oP NOA HOSt_ table WEC ineo o OE Examine modify the host table
122. d directly with the configuration of the CN2610 or configure the CN2610 at a later time In this section we explain how to configure Real COM Mapping 4 43 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 1 Start the Manger by clicking on Start gt Properties gt CN2610 Server gt CN2610 Server Manager and then click the server you would like to configure The ports will be shown in the right pane of the window A NPort Pro Manager Custom Available Available Available Available Available Available Available Available 0o wm N e wN 2 Right click the CN2610 you wish to configure click the right mouse button and then select Server Properties A NPort Pro Manager Custom E NPort Server a EN 2510 8 Available Available Available Available Available Available Available Available FVV 4 44 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 3 On the General page you can see the server s Serial No and modify Server Name Server IP and Netmask Select the Enable option to the right of DHCP if the network parameters are assigned automatically by a DHCP server Server Properties 4 On the Password page set up a password for this CN2610 for added security Check the Auto Save Password on this computer box if you want your computer to remember the password Server Properties
123. dary host IP Auto login prompt Password prompt Login user name Login password Terminal type Inactivity time Authentication type TCP alive check time Setting Value Notes Necessity Quit Key AE Defines the Quit key used to disconnect Optional the link between the current terminal session and the remote host It may be left blank for binary communication Auto link protocol None Telnet None Do not connect to the host Optional Rlogin automatically Telnet Connects to the host automatically by Telnet Rlogin Connects to the host automatically by Rlogin Telnet TCP port 23 Enter a number or leave the space blank Optional If not specified then by default port 23 is used If you want to use Telnet without a TCP port number set this option to 23 Primary host IP IP address or If specified designates a permanent Optional the name host to which the terminal will always be defined in the connected Host table Link by input IP Enable For users to enter the connection IP Optional Disable address manually Secondary host IP IP address or If specified designates a secondary Optional the name permanent host to which the terminal defined in the will be connected Host table Auto login prompt ogin Send ID information when this prompt is Optional received Password prompt assword Send Password information when this Optional p
124. dd remove unplug and troubleshoot your hardware To continue click Next lt Back i Cancel 4 25 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 4 Inthe Choose a Hardware Task window select Add Troubleshoot a device and then click Next to continue Add Remove Hardware Wizard Choose a Hardware Task Which hardware task do you want to perform 5 Inthe Choose a Hardware Device window select Add a new device and then click Next to continue Add Remove Hardware Wizard Choose a Hardware Device Which hardware device do you want to troubleshoot Add a new device E ACPI Fixed Feature Button Programmable interrupt controller System timer 5 Direct memory access controller rd 101 102 Key or Microsoft Natural PS 2 Keyboard 4 26 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 6 Inthe Find New Hardware window select No I want to select the hardware from a list and then click Next to continue Add Remove Hardware Wizard Find New Hardware Windows can also detect hardware that is not Plug and Play compatible 7 Inthe Hardware Type window select Multi port serial adapters from the Hardware types list and then click Next to continue Add Remove Hardware Wizard Hardware Type What type of hardware do you want to install Imaging devices R Infrared devices Memory technology driver gt ulti port serial ada
125. de 08 Redundant COM Redundant Redundant COM mode Configuring Redundant COM Mode Redundant COM mode supports a dual LAN network structure between the CN2610 s COM port and the host computer 1 Move the cursor to the Description more setting column and then press Enter CN2610 8_48 YS il Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting ul Redundant Redundant Redundant COM mode 02 Redundant Redundant Redundant COM mode 03 Redundant Redundant Redundant COM mode 04 Redundant Redundant Redundant COM mode 05 Redundant Redundant Redundant COM mode 06 Redundant Redundant 07 Redundant Redundant Redundant COM mode 08 Redundant Redundant Redundant COM mode l l l l 8 4 CN2610 User s Manual Redundant COM 2 The pop up selector contains input display fields for TCP data port TCP command port Max connection Allow driver control Skip jammed IP and TCP alive check time Each item is described in detail below the figure TOP data POrt TCP command port Max connection Allow driver control isable Skip jammed IP isable TCP alive check time 2 minutes Setting Value Notes Necessity TCP data port 950 965 The host uses this value to determine
126. des 2 brackets and 8 screws Desktop Kit includes 4 pads 1 2 CN2610 User s Manual Introduction Front Panel LCM Display Panel Push Buttons CN2610 16 port RS 232 Async Server Reset Button Ready LED LED Indicators Feature Description Press the Reset button for 5 seconds to load factory defaults The CN2610 will Reset Button beep twice when the configuration has been reset Push Buttons Used for configuring the IP address and other parameters Ready LED Red Indicates that the CN2610 is receiving power Green Indicates that the CN2610 s OS is ready Serial Tx Green Indicates serial port transmission Serial Rx Yellow Indicates serial port reception Rear Panel Power Input RS 232 Console Port Serial Ports Power On Off Switch 10 100BaseT Ethernet Ports Socket Port Description AC Power Input CN2610 8 and CN2610 16 Automatic detection of 100 240V 47 63 Hz AC power supply Power On Off Switch I indicates power on O indicates power off AC models only Console 8 pin RJ45 RS 232 port for console terminal connection LAN 1 8 pin RJ45 auto detectable 10 100 Mbps UTP port LAN 2 8 pin RJ45 auto detectable 10 100 Mbps UTP port Serial Ports 8 or 16 8 pin RJ45 ports for DCE modem type connections Bottom Label The server s serial number and MAC address are printed on a label fixed to the bottom of the server The CN2610 has 2 LAN ports each with i
127. e device CN2610 is connected to external serial devices In this way one host can use a TCP IP connection to control multiple serial devices from a remote location We use ports 5 6 7 and 8 on both CN2610s to illustrate A IBM workstation A with multiport board iy ae A RS 232 enoet Router fo eee occ ae ro l lt an p x f Q f l d 7 n i NOTE Configure the Host CN2610 s serial ports for RTELNET mode and configure the Device CN2610 s serial ports for TERM_BIN mode Configuring the Host CN2610 Open Port Menu gt Mode to select the Multiplex application 1 From the MAIN MENU select Port and then press Enter Cho TO E E Vn Server Port EEr oro sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 14 3 CN2610 User s Manual Setting Up Multiplexor 2 From the PORT MENU select Mode and then press Enter C2 61 0 O O 7 ORT MENU Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We first use Port 6 to illustrate CNAGIO e ak W210 Mode
128. e Authentication type TCP alive check time 14 9 CN2610 User s Manual Setting Up Multiplexor Setting Value Notes Necessity Quit Key AE Defines the Quit key used to disconnect Optional the link between the current terminal session and the remote host It may be left blank for binary communication Auto link protocol None Telnet None Do not connect to the host Optional Rlogin automatically Telnet Connects to the host automatically by Telnet Rlogin Connects to the host automatically by Rlogin Telnet TCP port 23 Enter a number or leave the space blank Optional If not specified then by default port 23 is used If you want to use Telnet without a TCP port number set this option to 23 Primary host IP IP address or If specified designates a permanent Optional the name host to which the terminal will always be defined in the connected Host table Link by input IP Enable For users to enter the connection IP Optional Disable address manually Secondary host IP IP address or If specified designates a secondary Optional the name permanent host to which the terminal defined in the will be connected Host table Auto login prompt ogin Send ID information when this prompt is Optional received Password prompt assword Send Password information when this Optional prompt is received Login user name Login ID Optional Login password Login P
129. e However when a CN2610 is configured in this way there is only 1 IP that is involved in the transmission 5 You might have another expectation when setting up the CN2610 to serup a fail over redundant connection Generally redundancy means that a NIC has 2 network interfaces connecting to 2 different switches or hubs When one of the connections switches or hubs fails the other one will take over This definition of redundancy differs from the one used in the CN2610 The CN2610 has 2 independent MAC addresses and IP addresses A 4 CN2610 User s Manual Troubleshooting Terminal Port Problems Problem When a terminal is connected to one of the CN2610 s serial ports no message is displayed on the terminal attached to the CN2610 terminal port when it is powered on Solutions gt One of the possible reasons is that this serial port is configured to Disable mode or to another application mode Using the Serial Console or Telnet Console select Port gt Mode and then move the cursor to the Application corresponding to the serial port and change Disable to Terminal gt Check to see if the terminal s serial port is set to the same settings as the CN2610 s serial port Use Serial Console or Telnet Console select Port gt Line and then move the cursor to the corresponding serial port and check to see if Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl settings are the same as the terminal s seria
130. e Mode column for the port and then press Enter CNA ILE We Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting omi NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Async Server Proprietary Protocol 05 NT Real COM Async Server Proprietary Protocol 06 Dialin out Auto Term SLIP PPP identification 07 Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol NT NT Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application on more setting 01 NT Real COM rver Proprietary Protocol 02 NT Real COM rver Proprietary Protocol 03 NT Real COM rver Proprietary Protocol 04 NT Real COM xver Proprietary Protocol 05 NT 06 07 08 Dialin out Auto Term SLIP PPP identification Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Real COM rver Proprietary Protocol NT NT 12 4 CN2610 User s Manual Setting Up Dial in Out 3 4 Move the cursor to the Description more said column and then press Enter C261 nM Mode Line mOdem Welcome_MSG Quit Examine modify the operatio
131. e Parity check FIFO Yes No FIFO setting Default is Yes RTS CTS Yes No Hardware flow control XON XOFF Yes No Software flow control Discon Ctrl None DSR off DCD off Inactive for these modes CN2610 User s Manual Redundant COM 4 Repeat the above steps to set all lines 5 Press Esc to return to PORT MENU Save 1 Press Y to save previous settings when exiting PORT MENU Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Warning If any field changed in this menu use Restart System to take effect Press any key to continue 2 You may also save later From the MAIN MENU select sAve to save all changed settings and then press Enter to confirm CZ GO S ve 0 Server Port seTting Utility Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select Restart 1 Return to MAIN MENU and select Restart CNZ610 sansa ola 1 eon ole me W Lemos Restart BRek Restart the whole system or selected async ports Enter select ESC previous menu 8 8 CN2610 User s Manual Redundant COM 2 Select System and then press Enter to continue 102 610 2 en VZO O OOOO O System ELis Quit Restart the Async Server ESC back to menu Enter select Warning 00 0 Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 3 The system will restart a
132. e at the same time 0 for simultaneous unlimited login sessions Maximum minutes login 60 The user has only 60 minutes in each login session 0 for unlimited time Idle minutes force to logout 5 If the user is idle for 5 minutes the session will be terminated 0 for no kick out Maximum login 500 The user has max 500 hours per month hours month ates ost 0 means unlimited access Select OK to save Extended Permission Maintenance Modify User Permission Basic Permission Maintenance gt xtended Permission Maintenance Save amp Exit CN2610 User s Manual RADIUS Server gt dd Permission Group Modify Permission Group Delete Permission Group 4 4 4 Add Extended Hint Sun Mon Tue Wed Thu Fri Sat 0 1l accept reject Input 1000001 Group Name eer rr re Expires days after first login 30 Login time interval in a day 08 00 22 00 Not allow login days in a week Sun Sat gt aximum login hours 3 Ok 4 5 5 55 5 Extended Permission Example Description Group Group Name Example2 Name of this permission setting Days to expire after first 30 The user account expires after 30 days after login first login
133. e equipment or objects on top of the unit as this might damage the server Pads Bottom of CN2610 Rackmount The CN2610 is designed to be mounted on a standard 19 inch rack Use the enclosed pair of L shaped metal brackets and screws to fasten your CN2610 to the rack cabinet Each L shaped bracket has 6 holes leaving two outer or inner holes available for other uses You have two options You can lock either the front or rear panel of the CN2610 to the front of the rack Locking the front panel is shown in the following figure L Shaped Metal Brack y 2 2 CN2610 User s Manual Getting Started Wiring Requirements A ATTENTION Safety First Be sure to disconnect the power cord before installing and or wiring your CN2610 Wiring Caution Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment Temperature Caution Be careful when handling the CN2610 When plugged in the CN2610 s internal components generate heat and consequently the board may feel hot to the touch You should also observe the following common wiring rules e Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make su
134. e metric hop in this case is 2 route hops CN2610 8 CNAE O S WS V0 ap obmoPmlt leMee A Oo Route_table RARS an o EO Examine modify the routing table ESC back to menu Enter select Gateway Destination Netmask L203 6T 6254 l 0 000 I 1029 020 20S O07 65252 2OS 65 66 0 12352553435330 J T 5 a F a 15 6 CN2610 User s Manual Setting Up Routing Configuring Multiple Point Routes f f Web FTP E mail News A Server Server f es Ethernet WwW 203 67 6 TCP IP CN2610 203 67 6 253 Console Server P Router 203 67 6 254 RS 232 RS 232 Modem 1 P P Modem 2 Internet Modem 3 7 Modem 4 A 202 6 6 254 S2 N2610 201 2 2 254 OT eae Console Server Console Server T e 4 Printer i MRP Printer MRP JG Server JG Server gt gt 7 202 6 6 3 gt gt Z 201 2 2 1 Phone Line Phone Line Ethernet Y Ethernet 202 6 6 ff 201 2 2 Bb f 6 A P Ss o Ss PC PC PC PC For multi location enterprises the CN2610 can be placed in different branch offices and used as both a multi point router and remote access server When hosts e g the Web FTP and E mail News servers shown in the figure send requests to hosts on another network such as 202 6 6 or 201 2 2 the CN2610 delivers the request to the remote end CN2610 202 6 6 254 or 201 2 2 254 as the next hop router Requests to Internet hosts are still sent through router 203 67 6 254 as the next hop router Fo
135. e network the CN2610 will use the netmask to determine if the destination TCP IP host is on the same subnet If the address is on the same subnet a connection is established directly from the CN2610 Otherwise the connection is established through the default gateway If this field is left Blank the netmask will depend on the default IP address class which depends on the IP address itself The netmask is 255 0 0 0 for class A 255 255 0 0 for class B and 255 255 255 0 for class C Default gateway IP address This field contains the IP address of a router on the local network The default gateway is used when a packet is sent to an IP address that is not on the subnet specified in the CN2610 s local routing table Ethernet speed If the Ethernet port is active the Ethernet speed will be set automatically to 10BaseT or 100BaseT This field cannot be modified Ethernet address This field contains the hardware Ethernet address This field cannot be modified 2 15 CN2610 User s Manual Getting Started Server Configuration Adv 1 From the MAIN MENU use the arrow keys to select Server and then press Enter SGE OO O 7 o MENU Server Royal oTe S N Oh os i so a E E Examine modify async server node table configuration Enter select ESC previous menu From the SERVER MENU select Adv and then press Enter CHOCO 8 WS VO Lan Adv E Host_table Route_table User_table Quit Examine modify async serv
136. eck to see if the terminal is set to 115200 bps 8 data bits no parity 1 stop bit gt Check to see if terminal type setting is correct The console only accepts ansi vt100 or vt52 gt Press Ctrl L to refresh the display Question How can I restore the CN2610 to the factory default settings Solution gt After entering the Console window select setting gt Default and then press Enter The CN2610 will be restored to the factory default settings CNE EOS Ik AO Server Port SeTting sAve Utility Restart Exit Export or import comtignuration Enter select ESC previous menu CNZELO 629s V2 0 poo aoa Default EEk Load the factory setting ESC back to menu Enter select A 2 CN2610 User s Manual Troubleshooting Question If I forget the password for my CN2610 what should I do Solution gt Press the Password Reset button on the CN2610 s front panel for more than 5 seconds The password stored in the Flash ROM will be erased Refer to Chapter 1 for more details CN2510 16 port RS 232 Async Server Reset Problem I used Telnet Console in a Windows 9x NT environment but I couldn t use the arrow keys to select options Solution gt In Telnet click the Terminal menu choose Preferences and then select VT100 Arrows in the Terminal Preferences window Click OK to return to the MAIN MENU The arrow keys should work properly now of Telnet 192 168 2 180 Console te
137. ect TCP IP protocol and then click Next to continue Remote Client Protocols Routing The protocols required for remote client access must be available on this server 0 x i i i I Routing and Remote Access Server Setup Wizard x IP Address Assignment You can select the method for assigning IP addresses to remote clients B 14 CN2610 User s Manual RADIUS Server Address Range Assignment You can specify the address ranges that this server will use to assign addresses to remote clients New Address Range 7 Managing Multiple Remote Access Servers Routing You can manage all of your remote access servers centrally B 15 CN2610 User s Manual RADIUS Server Setting up Windows 2003 Hosts Windows 2003 uses IAS service instead of RADIUS service For this reason you need to install IAS service to use RADIUS with Windows 2003 IAS service will not be installed by default 1 Click Start gt Add or Remove Programs gt Add Remove Windows Components 2 With Windows Components selected choose Network Services Windows Components Wizard E xj Windows Components eed fou can add or remove components of Windows f To add or remove a component click the checkbox A shaded box means that only part of the component will be installed To see what s included in a component click
138. ed Ports COM Number coms current in use COM setting V Enable Redundant COM C Mapping IP addresst i 92 168 34 111 C Wapping IP address2 117216 0 112 X Cancel Enable Redundant COM is a default it will enable 2 LAN automatically If disable Redundant COM it will become Real COM mode either LAN can be selected for mapping IP address NOTE Before configuring the driver for Redundant COM mode you must first configure the corresponding port of the CN2610 firmware for Redundant COM mode 16 23 CN2610 User s Manual Administrative Utilities 9 Click the Advanced Settings tab to modify Tx Mode FIFO and Flash Flush comport setting eee Port Number 1 Port s are Selected Basic Settings Advanced Settings Serial Parameters Security F Apply All Selected Parts The FIFO settings will overwrite the firmware setting Tx Mode HiPerformance FIFO Enabe H Network Timeout 5000 ms 500 20000 V Auto Network Re Connection Return error if network is unavailable JV Fast Flush Only flush local buffer X Cancel Tx Mode Hi Performance is the default for Tx mode After the driver sends data to the CN2610 the driver immediately issues a Tx Empty response to the program Under Classical mode the driver will not send the Tx Empty response until after confirmation is received from the CN2610 s serial port This causes lower throughput Classical
139. egistry and makes the COM port available for use The host computer will not have the ability to use the COM port until the COM ports are activated Click Yes to activate the COM ports at this time or click No to activate the COM ports later ioii Eie COM Mapping View Help i amp A R B a Exit Add Remove Apply Undo Setting No COMPort_ IP Address 1 Regie 1 COM18 192 168 34 219 950 966 Port1 2 COM19 192 168 34 219 951 967 Port2 3 COM20 192 168 34 219 952 968 Port3 4 COM21 192 168 34 219 953 969 Port4 5 COM22 192 168 34 219 954 970 Port5 6 COM23 192 168 34 219 955 971 Port6 7 COM24 192 168 34 219 956 972 Port 8 COM25 192 168 34 219 957 973 Port8 9 COM26 192 168 34 219 958 974 Port9 10 COM27 192 168 34 219 959 975 Port10 11 COM28 192 168 34 219 960 976 Port11 12 COM29 192 168 34 219 961 977 Port 2 13 COM30 192 168 34 219 962 978 Port13 14 COMA a 19216A 34 71A 962 079 Part A 16 Total COM Port Wy 5 In Windows XP a message is displayed during activation of each port indicating that the software has not passed Windows Logo certification Click Continue Anyway to proceed Hardware Installation i A The software you are installing for this hardware NPort Communication Port 1 has not passed Windows Logo testing to verify its compatibility with Windows XP Tell me why this testing is important 16 21 CN2610
140. elect Restart 1 From the MAIN MENU select Restart CNAENO ia sae ola oTe S Weems Restart ERI ei Restart the whole system or selected async ports Enter select ESC previous menu 6 7 CN2610 User s Manual Setting Up Raw UDP 2 Select System and then press Enter to restart the system and terminate the Telnet session 102 61 0 2 7 System Bzenae Quit Restart the Async Server ESC back to menu Enter select Watning 114 Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 6 8 7 Setting Up the Dual host Redundant Data Acquisition System This chapter shows how to set up a CN2610 that allows the redundant terminal on the redundant Ethernet network to access the CN2610 s serial ports DRDAS mode allows users to set up a highly redundant structure This chapter introduces the APIs for the following functions Q Accessing the Console Utility QO Selecting the Application Configuring DRDAS Mode QO Configuring the Serial Ports Save Restart CN2610 User s Manual Setting Up DRDAS Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program
141. elect the device driver you want to install for this hardware Click Have Disk to install from the CD Add Hardware Wizard Select the device driver you want to install for this hardware N Select the manufacturer and model of your hardware device and then click Next If you have a disk that contains the driver you want to install click Have Disk Digi International Moxa Technologies Co Ltd Moxa Technologies Inc MOXA C104 Series ISA Bus Version 1 9 0 0 2004 74 MOXA C104H PCI Series PCI Bus Version 1 8 0 0 2 MOXA C104H PCI Series PCI Bus Version 1 9 0 0 2 MOA CITAHI Caries ICA Rusl Version 1900 ona gt A This driver is not digitally signed Have Disk Tell me why driver signing is important lt Back Cancel 4 11 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 10 Locate and then select the driver file NPSERVER INF Click Open to proceed with the installation Locate File 2 x Look jin E winx J Ofe m NPortTool My Recent Documents E Desktop My eee A My Computer Ki eters File name NPSERVER x Places Files of type Setup Information inf Cancel 11 Select the correct CN2610 model and then click Next to continue Add Hardware Wizard Select the device driver you want to install for this hardware Select the manufacturer and model of your hardware device and then click Next IF y
142. en aan aa di ted sete ste sspten OSE EER onsets ERSS REN EO 11 4 Configuring the Serial Ports psies ornini isterati ae ie REEE E ri a ain et 11 5 SIVE n ar a E r a r E a E r A E tap E 11 7 RESLart isc E E SAE S S N 11 7 Sete S Up m KOTSE spiced eased E E E E A E EEE 11 8 Installing and Compiling Fixed TTY Driver eseeeeeeeeeeeeeeiererrersrrrerrererrsesrre 11 8 Fixed TTY Driver for Different Applications sseeeeeeeseseeseeeeerersersrrrrrrererrssrre 11 9 Using Fixed TTY Driver niie tide a e a a a a eaeh a e 11 10 Setting Up Dialin OUtccca el eee eee 12 1 Accessing the Console Utility niseni enp oes iaienl eta tiatl E E 12 2 Selecting the Application oeron tsere eieae deat aa Eeo E A A 12 3 Configuring PPPD PPP Modes 2 icscsussscisaesditesssesespsotseesh sabeasssecdstnabbeses his seosehaosonioniedehs 12 4 Configuring SLIPD SLIP Modes isiin rosses ree es een Eenes aE En EnSan EE 12 6 Configuring Dynamic Modes inae E E R E A 12 8 Configuring the Serial Ports iiion sineach gia eatas oi a i a 12 13 Configuring Modem Initialization eessesecsessecesesecesecseesecneeeecsaeeeesecaeeeeeneseenaees 12 14 Optional Welcome Message sccessscssssecssecseesecneeseceseeeessecaeeseeneesecsaeeeeaecaeeseeneeseenaees 12 15 Configuring Optional Local User Information ee eeeceseeseesecneeeecneeeeceaeeeeeaeeneeseens 12 15 SAVE EE E Stash keer auseetures Bevbace spevusceds esbecdta E EE EEE 12 16 REStart AE ENE A ETT 12 16 Setting Up Print
143. er Manager The CN2610 Windows Driver Manager is designed to be used with CN2610 serial ports that are set to Real COM mode The Driver Manager manages the installation of drivers which allow you to map unused COM ports on your PC to serial ports on the CN2610 These drivers are designed for use with Windows 95 98 ME NT 2000 XP 2003 Vista When the drivers are installed and configured devices that are attached to serial ports on the CN2610 will be treated as if they were attached to your PC s own COM ports 1 Click the INSTALL COM Driver button in the CN2610 Installation CD auto run window to install the CN2610 Windows Driver Once the installation program starts running click Yes to proceed 2 Click Next when the Welcome screen opens to proceed with the installation lol x Welcome to the NPort Windows Driver Manager Setup Wizard This will install NPort Windows Driver Manager Ver1 2 on your computer it is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup rs on 16 16 CN2610 User s Manual Administrative Utilities 3 Click Next to install program files to the default directory or click Browse to select an alternate location Select Destination Location Where should NPort Windows Driver Manager be installed 4 Click Next to install the program s shortcuts in the appropriate Start Menu folder Select Start Menu Folder Whe
144. er again to save and any other key to cancel CN2610 8 19 aA Server Port seTting Utility Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select Restart CN26 SSA a ola oTe S Wma Restart Maieme Restart the whole system or selected async ports Enter select ESC previous menu 2 Select System and then press Enter to restart the system and terminate the Telnet session System zene Quit Restart the Async Server ESC back to menu Enter select Weteran LAA Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 5 9 CN2610 User s Manual Setting Up Device Control ASPP Library Introduction The CN2610 Documentation and Software CD contains example programs that illustrate how to control an ASPP port After uncompressing the file ASPP tar z the folder aspp as h will contain several basic subroutines The following subroutines are used to control an ASPP port sio_init start ASPP Library sio_open ipaddr p open a serial port sio_close fd close a serial port sio_ioctl fd baud mode configure a serial port s baudrate parity etc 1 2 3 4 5 sio_baud fd baud mode configure serial port s baudrate 6 sio_flowctrl fd mode configure hardware and or software flow control 7 sio_Ictrl fd mode line control 8 sio_Istatus fd check line status 9 sio_flush fd func clear input output buffer 10
145. er basic configuration Enter select ESC previous menu The Adv page contains input display fields for RADIUS server IP RADIUS key UDP port Enable RADIUS accounting SNMP community name SNMP trap server IP address Ethernet IP forwarding Routing protocol TCP retransmission timeout and SIO data transfer timeout Each item is described in detail below CN261 Ipo To En ACV Orio Oe ou E E amor of EOE Examine modify async server advance configuration ESC back to menu Enter select Radius server IP RADIUS key UIDs ge SLAS Ae LSL Enable RADIUS accounting SNMP community name SNMP trap server IP address Ethernet IP forwarding Routing protocol TCP retransmission timeout Games SOA GOCO ws SIO data transfer timeout Gar bole 5 O TOO wS RADIUS server IP The IP address of the RADIUS Remote Authentication Dial In User Service server is used to authenticate remote dial in users connecting from an ISP Internet Service Provider Leave this field blank if you do not have a RADIUS server on your network Windows NT includes RADIUS software For UNIX based platforms refer to Appendix B for information about setting up a RADIUS server NOTE The RADIUS server and the CN2610 SHOULD be able to communicate with each other To verify this check to see if you can ping from each server to the other RADIUS server IP This is the IP address of the RADIUS server RADIUS key This is a shared key used by the RAD
146. eral Configuration Driver m NPort Server Async Server Status Model CN2510 8 IP Address 192 168 127 254 Port Status COM Number COM13 COM20 Ports Setting 4 23 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 9 Check the box es next to the port s you would like to modify and then click Modify Setting Port Configuration Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance 4 24 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Setting up Windows 2000 Hosts In this section we explain how to set up a host in a Windows 2000 environment Installing a Server 1 Unzip the Windows 2000 driver file located on the CN2610 CD ROM to your hard disk 2 Run the Windows Add Hardware Wizard located in the Control Panel ioixi File Edit Yiew Favorites Tools Help e a2 Back Forward Up Search Folders History Address E Control Panel Go v Add Remove Administrative Automatic Programs Tools Updates of Date Time Display Folder Options 4 9 Game Internet Kevhnard Lirensinn xl Installs removes and tre 3 When the Welcome to the Add Hardware Wizard window opens click Next to continue Add Remove Hardware Wizard Welcome to the Add Remove Da SS Hardware Wizard This wizard helps you a
147. erminal Access application is used to connect terminals to Unix or Windows Servers over a network The terminals connect to the CN2610 s serial ports at a remote site with terminal commands transmitted over the network via the CN2610 s Ethernet port The Terminal Access application allows you to use fast keys used in many terminal applications and switching sessions on the same terminal The CN2610 supports ASCII terminal and Binary terminal with up to 8 simultaneous sessions for each port Refer to Chapter 9 for detailed information and configuration instructions 3 9 CN2610 User s Manual Knowing Your Application Multi host TTY Multi host TTY Unix Unix Unix Unix Moxattyd Moxatiyd Moxattyd Moxatiyd a a is y TCP IP cen2610 CN2610 ie Terminal Swith Session Between different Unix server by Hot Key The Multi host TTY application is ideal for connecting over a network to multiple Unix hosts from several sessions simultaneously When communication begins the networked Unix server must first enable Moxattyd to activate the TTY port s mapping function Moxattyd will initiate the connection with the CN2610 and the CN2610 will listen to the connection requests issued by various Moxattyd over different TCP ports Once the connection is established the Terminal server can use hot keys to switch sessions allowing one terminal to control different Unix hosts Refer to Chapter 10 for detailed infor
148. ersecsaceecsaecaeesecneeseeneeeeeeas 16 30 EXPL i s aor EEEE hbche de cbucguus cusses te E e vedas E NEE A E Soaraa tacbucbwas ove 16 32 Console Terminal Export vv Ac5 iaiiee aha hiloe anise sbalia R 16 32 Remote RCP Export isni sists netis te A avin eae reeta Aad ensei A ie RERS Ees ie 16 35 dani DLO n PASS EE E ER TE sa saeseadstasstbesawecabinsussasusseseesess 16 35 Console Terminal IMport eesin ieseni oere r Ee E Epen e N SEa uas 16 35 Remote RCP Import iee nga ses teer a EEEE E ae E EEEE 16 38 DePaul ti sis riae aa a a a a a a he hee WER tack teat E BEE 16 39 Appendix A Appendix B Appendix C Appendix D Appendix E TFOUDIESNOOUING oc nicctissceccicadinicdtvaiteadinensinaasteeusiaedaiatianladidnivngecns A 1 Console Terminal Problems siiani oieri aeaa EA E A i E R eiet A 2 Configuring Dual Ethernet PortServer isinish siiri A 4 Terminal Port Problems iinei en ai ei arae wie Ea aE EErEE KEE ieai A 5 Saving the CN2610 s Parameters ireen ee ceeeseeeeeeeeeeeceeeeeeeeeeeeseeeeeeseessecaecsaecsaeseaeeaeeeas A 5 ASPP Port Problems iecere pea ee a ea ee A 6 SLIP PPP Connection Problems insara r a E csensecbats A 6 RADIUS Problems iana a E E E E ane tS ea ae A 6 RADIUS S i Vet ois cc cias esas casecsanssaannsuacashdcntaceh adenguasdndseands tavavnccaeaecndeseancedan B 1 W hat 1S RADIUS ienne e a aae e E ae Aa Rar cits A n tauedtoen ee git B 2 D fi itiom e eann a nean e e aeaa eR Rie lino ied alata aS B 2 Client Server Architecture nki
149. es asprint c and asprint mak First uncompress printer tar Z to the printer directory and then locate the files asprint cand asprint mak To compile and link you may need to modify the source file asprint c For instance in SCO UNIX you must link to the 1ibn1s a library in Solaris to libnsl a and in Venix tothe libnsl_s a 13 9 CN2610 User s Manual Setting Up Printer Setting up a SCO Unix Host Steps SCO UNIX Command Description Uncompress all programs tar dev fdO Uncompress printer tar Z to printer tar xvf printer tar Z compile link make f sco_unix mak make printer node mknod dev iop1 p Create a unique pipe name for each printer group Since there are 16 groups of TCP port numbers from 2048 to 2063 you need to create 16 respective pipe names For example iop1 iop2 iop3 etc set it to printer chown lp dev iop1 Change the pipe owner to 1p set rw chmod 600 dev iop Change access permission to 600 or TW set printer name usr lib lpadmin Redirect the printer spooler to write to pLaser1 v dev iop1 pipe iop1 Assumes the printer name is Laser1 execute asprint for Group 01 asprint dev iop1 CN2610 IP address 2048 amp Start asprint utility to read from pipe iopl and write to the CN2610 printer port dev iop1 the device name the spooler is writing to CN2610 the host name of the
150. et a secsccesseccecesscccecevast cctcncceenccesveeceeteessaaccdeeesssveceesaarecceeene 13 1 Accessing the Console Utility 2 ses ciccuieven te sheets dated 13 2 Selecting the Application 000 eeecesesecseeeseeecsecsecsaeeecsaeceeesecseesecnaseeesaeseeaecaeeseenesseeeaees 13 3 Configuring RAW PRN Mode 2 0 00 eeeesecssecceseceeeeessesesscesacenessecaeesecnesseesaseeesaecaseseeners 13 4 Configuring LPD PRN Modein arinei eito eR Aa oe RREA EEE AVR iS 13 6 Configuring the Serial Ports j 2ciesceiiciaest cond patie ee aa aa rE Ea Ea are R E 13 7 DAVE sisi SE E A S ae a 13 8 RETE a Ae EOE OTE ESE AE A ESE E deat Sava E E E 13 9 Settins up Unix HOStS iina ena ea ee ieee lee 13 9 Setting upa SCO Unix H st reini nrn e a ES 13 10 Setting up a SOLARIS X86 Host sesesseeeeseseseseserrsresssrsrsrerreresssesrsrerresersesesee 13 11 Settings up a LINUX HOS eee eaeoe es eenean a douse e Pia aeea aeie tenet 13 12 Setting up Windows Hosts c sscsssesesesensesesesenerensesseosensnsssneusesssesesenenensesonssensepsnenee 13 13 Setting up a Windows NT Host 0 cece eceseeeeeseceeeeecseeeecseeeecsaeceeesecneeseeneseesaeeees 13 13 Setting up a Windows 2000 Host ees eesssecssesecseeseceeeeecaeceeesecseeseeeeaeeseenees 13 17 Chapter 14 Chapter 15 Chapter 16 Setting Up Multiples c 4240nhianindtienin enim 14 1 Accessing the Console Utility Kreisis teriais ir i r E a i eaa e 14 2 Selecting the Applicaton iss scc c virescecocinthievt ste
151. ey Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 9 2 CN2610 User s Manual Setting Up Reverse Terminal Selecting the Application Open Port Menu gt Mode to configure the Reverse Terminal application 1 From the MAIN MENU select Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application Description more setting 01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Async Server Proprietary Protocol 05 NT Real COM Async Server Proprietary Protocol 06 Async Server
152. folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 7 2 CN2610 User s Manual Setting Up DRDAS Selecting the Application Open Port Menu gt Mode to configure the DRDAS application 1 From the MAIN MENU use the arrow keys to select Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter CNAS S m S270 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description
153. g information to configure the CN2610 Check with your network administrator if you do not know all of the required information Basic CN2610 Information Name Location LANI IP address LANI IP netmask LAN default gateway IP address LAN2 IP address LAN2 IP netmask LAN default gateway IP address Domain server 1 IP address Domain server 2 IP address WINS server IP address Console password Accessing the Console from a Telnet Terminal Connect the CN2610 to your LAN and then turn on the power Use the MOXA Windows Utility to find the CN2610 s IP address and then telnet to the IP address to enter the CN2610 console 2 4 CN2610 User s Manual Getting Started CN2610 Windows Utility The CN2610 Utility is a convenient Windows utility that can be used to find both the name and IP address of your CN2610 Once you know the IP address you can telnet the CN2610 over the network to complete the configuration process and to gather information about all servers on the network 1 Run upgrade exe located in the Software Firmware folder on the CN2610 Documentation and Software CD or run CN2610 Tool gt Firmware Utility from the Start menu fH NPort Tool al Firmware Utility Fil Monitor Version info 2 The CN2610 Utility will search for all CN2610s on the network x Please wait while system is searching all available NPort Servers 3 The CN2
154. gt OS N ran TXTotalCnt RXTotalCnt TXBuf RXBuf TXAvg RXAvg DTR RTS DSR CTS DCD 0 0 0 0 0 ON ON ON ON ON ON ON ON ON ON 2O SD a E E e a E D E D Cer Se E L E D RD Re DY RS CD i KO OS a SD Total transmitted characters Total received characters Queued data bytes in the transmit raw buffer Received data bytes in the receiving raw buffer Current approx characters per second transmit rate Current approx characters per second receiving rate Current DTR status Current RTS status Current DSR status Current CTS status Current DCD status 2 Press Esc to return to Async 16 5 CN2610 User s Manual Administrative Utilities Routing 2 PPP Trace 1 From the MONITOR MENU select Routing and then press Enter ICN2610 8 CN26 Network Async async Setting ROUting Ea a ia Kee Monitor current routing table ESC back to menu Enter select Destination Gateway HA Netmask Metric O50 5050 Ug GS g dk S OnO70 0 abs ADIs A 5250 A0Si sO 7a Gn 251 BIS AIS ASDA al AV 05 6650 2033 S15 6 232 DOS 5 ADS ADS 40 0503040 AOS 587 oOo Zane 0505050 2 al VO 2 NES Os To hea be DDS ZDS pa ae af 192e 9m2 aN Rs z 0 Iface Name of the physical network interface Destination Network or host that the router allows you to connect to Gateway IP Address of the gateway you configured for this route If you are directly connected this is a local address Otherwise it is
155. hernet interface Optional Allow driver control Enable Disable default Disable This option determines how the port will proceed if driver control commands are received from multiple hosts that are connected to the port If Disable is selected driver control commands will be ignored If Enable is selected control commands will be accepted with the most recent command received taking precedence Optional Skip jammed IP Enable Disable default Disable This option determines how the port will proceed if multiple hosts are connected and one or more of the hosts stops responding as the port is transmitting data If you select Disable the port will wait until the data has been transmitted successfully to all hosts before transmitting the next group of data If you select Enable the port will skip the host that stopped responding and continue data transmission to the other hosts Optional TCP alive check time 0 99 minute default 7 The time period the CN2610 waits before checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection Optional 3 Press Esc to return to PORT MENU 1 If either LAN gets disconnected it will take at least 1 minute for the LAN to recover after reconnecting 2 If both LANs get disconnected you will need to reopen your application software s COM port for data to transmit pro
156. hoReq Received packets from remote Ping request REchoRply Responding packets to remote Ping request SEchoReq Received packets from local ping request SEchoRply Responding packets to local ping request 16 4 CN2610 User s Manual Administrative Utilities UDP statistics Received ErrPorts ErrHeader Sent TCP statistics Received ErrHeader CurrEstab ErrPorts Opens Sent ReSent Received UDP datagram packets Received UDP datagram packets with invalid destination port Received UDP datagram packet with incorrect header Sent UDP datagram packets Total received packets of segments including error packets Error packets e g bad TCP checksums The counter of TCP connections for which the current state is either ESTABLISHED or CLOSE WAIT Received TCP datagram packets with invalid destination port TCP connections Total sent packets including those on current connections Retransmitted packets Press Esc to return to Network From the MONITOR MENU select Async and then press Enter Line Network CNZ610 38 19 Vz 2 IMONITOR MENU Async asyne Setting Routing PPP Trace Monitor asynchroenous port line status Enter select Line Network ESC previous menu Async async Serting Routing lt PPP Trace Monitor asynchronous port line status ESC back to menu Enter select TXTotalCnt RxTotalCnt TXBuf RXBuf TXAvg RXAvg DTR RTS DSR 180 els 0 oO fan CS as
157. iagnostic The CN2610 Diagnostic Utility which is used to test async ports Ethernet controllers and printer ports supports the following functions e Async port controller and internal loop back test e Ethernet controller internal and external loop back test e Printer port test 1 From the UTILITY menu select Diagnostic and then press Enter CN2610 8_19 v2 0 Ping Monito Diagnostic Upgrade Quit Loopback test and self diagnose Enter Select ESC previous menu 16 7 CN2610 User s Manual Administrative Utilities 2 If any of these tests fails contact MOXA to request repair services N2610 8 CN2610 8 WZ 0 Ping Monitor Diagnostic Upgrade Quit Loopback test and self diagnose ESC back to menu Enter select Asynchronous port controller test OK Asynchronous port loopback test OK Ethernet port controller test OK Ethernet port 1 controller loopback test Ethernet port 1 transceiver loopback test 3 Press Esc to restart the system Upgrade The operating system in the CN2610 is kept in the Flash ROM It can be upgraded using the Windows Utility from a locally connected CONSOLE Terminal using XMODEM protocol or from a Unix host using RCP protocol Upgrading with the Windows Utility One of the main features provided by the Windows Utility is to upgrade firmware If the CN2610 is connected to a Windows network this is the simplest method available for upgrading the firmware 1
158. ietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 INE ReaL GON is IASPE i gp t rver Proprietary Protocol NT 05 Real COM Z rver Proprietary Protocol 06 Device Control RAW BG Proprietary Protocol 07 NERES GOM J TASER Spe SSS rver Proprietary Protocol 3 Move the cursor to the Description more setting column and then press Enter The pop up selector contains input display fields for TCP port Source IP address Destination IP addr Inactivity time and TCP alive check time Each item is described in detail below the figure CNAS LOS LLO VZO Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application 01 NT Real COM 02 NT Real COM Source IP address 03 NT Real COM Destination IP addr 0S NT Real COM Inactivity time minutes 06 Device Control TCP alive check time minutes 07 NT Real COM 08 NT Real COM Setting Value Notes Necessity TCP port number Each of the CN2610 s serial ports is mapped Optional to a TCP port You may modify these port numbers but to avoid conflicts among TCP port numbers for other serial ports we strongly suggest using the default values 4001 for port 1 4002 for port 2 etc Source IP IP address for Specify an IP address for this port for Optional address the port application purposes If left blan
159. ime is 1 minute after turning the CN2610 on or off Fixed TTY Driver for Different Applications This section illustrates how to use Fixed TTY driver with a number of different applications Terminal Access To use terminal access the process getty must be activated when the system boots up To do this add the following entries to the file etc inittab For instance ts1 234 respawn etc getty ttypl ts2 234 respawn etc getty ttyp2 ts3 234 respawn etc getty ttyp3 ts4 234 respawn etc getty ttyp4 NOTE ttyp1 to ttyp4 device names are mapped to port 1 to port 4 on the CN2610 Transparent Printer Access It s not necessary to add additional entries to etc inittab for printer access as mentioned in the section on terminal access Since Fixed TTY driver is a fixed pseudo tty you can easily connect a serial printer to a MOXA CN2610 serial port to execute printing commands The following example is for SCO OpenServer Command Description usr lib lpadmin pLaserl v dev ttyp1 set printer name as Laser and use ttyp1 usr lib accept Laserl accept printer Laser1 enable Laserl enable printer Laser1 lp dLaserl file_nam print file to Laser Other Applications As mentioned earlier the system setup depends on which application you are using Since Fixed TTY driver is a fixed pseudo tty no additional setup is required to enable your applications to open tty devices 11 9 CN2610 User s Manual
160. in Name Server WINS function disable Enable or disable the WINS server The default setting is enable WINS server IP address If a WINS Server is connected to the network use this field to record the WINS Server s IP address TCP IP uses IP addresses to identify hosts but users often use symbolic names such as computer names The WINS Windows Internet Naming Service Server which uses NetBIOS over TCP IP contains a dynamic database to map computer names to IP addresses Console password If you specify a password write it down for safe keeping If you forget the password you will need to use the reset password button to reset it Only use the console password when absolutely necessary NOTE Write your console password in a safe place before setting the password Server Configuration LAN 1 From the MAIN MENU use the arrow keys to select Server and then press Enter CEOE 19 V2 0 Server EEL aeoe S A Oh os il Ws oh a C19 ota E Examine modify async server node table configuration Enter select ESC previous menu 2 From the SERVER MENU select Lan and then press Enter CH2GLOU 8 WS VO Info JRFEYE Adv Host_table Route_table User_table Examine modify async server basic configuration Enter select ESC previous menu CN2610 User s Manual Getting Started 3 The Lan page contains input display fields for DHCP client Async server IP address Async server IP netmask Default gateway I
161. information which details the type of service to deliver to the user for example SLIP PPP Telnet rlogin The CN2610 Async Server supports RADIUS protocol which requires only one database for remote user management The following topics are covered in this appendix Q What is RADIUS gt Definition gt Client Server Architecture Q Setting up the CN2610 gt Setting up the RADIUS Server IP Address gt Setting up Port Configuration Q Setting up UNIX Hosts gt Installing the RADIUS Execution File gt RADIUS Server Configuration gt Basic Extended Permission Group Setting Setting up Windows NT Hosts Setting up Windows 2000 Hosts Setting up Windows 2003 Hosts Ooo CN2610 User s Manual RADIUS Server What is RADIUS Definition Remote Authentication Dial up User Service or RADIUS is the standard for centralizing the authentication authorization and accounting of remote access users Here is a brief description of how RADIUS works When a user dials in to a remote access device that device communicates with the central RADIUS server to determine if the user is authorized to connect to the LAN The RADIUS server performs the authentication and responds with the result either accept or reject If the user is accepted the remote access server routes the user onto the network if not the RAS will terminate the user s connection The RADIUS server also provides accounting services if supported by the remote access se
162. ing Port Configuration Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance Hi Performance 11 Setting up Windows 95 98 ME NT Hosts In this section we explain how to set up a host in a Windows 95 98 ME NT environment You will first install the CN2610 Pro Manager program and then use this utility to configure the server We use Windows NT to illustrate the installation procedure 4 38 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Installing a Server 1 Unzip the Windows 95 98 ME NT driver file located on the CN2610 CD ROM to your hard disk 2 Locate and run the Setup exe file Vv RUIN Seperate meno space OR ce Browse 3 The setup program is used for both CN2600 and CN2610 Server Pro products so you will see a Welcome to CN2610 Server Pro window Click Next to continue Welcome to NPort Server Pro x Setup Wizard 4 39 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 5 Select a Destination Directory and then click Next to continue Select Destination Directory x Please select the directory where the NPort Server Pro files are to be installed D Program Files NPort lt Back Next gt Cancel 6 Click Next to finish installing CN2610 Pro Manager Setup Wizard x NPort Server Pro Setup has finished installing
163. ing of files between hosts without the need to enter passwords This can be done using the security file rhosts The format of RCP is as follows rcp from to The from and to arguments can either be specified as local files or remote files To specify a remote file use the format user hostname filename If the remote login ID is identical to the local login ID then user can be omitted i e only hostname filename is required The security file rhosts is a plain text file that must reside in the local user s home directory and must be owned by that user This file identifies those users who are equivalent to the local user and are given access without needing to enter a password 16 14 CN2610 User s Manual Administrative Utilities NOTE The file must contain at least a host and if the login ID is different on the remote host it must also contain the login ID This sample rhosts file is for the user john on the host sun The following three accounts are considered equivalent accounts The user has accounts on moxal and moxa3 with the same login ID and has an account on moxa2 as johnwu This comment line is ignored by the operating system Moxal com tw john Moxa2 com tw johnwu Moxa3 com tw john 1 Login to your UNIX LINUX host For example login to 203 67 8 22 as user john 2 Copy the CN2610 firmware file e g CN2610 rom to the current directory 3 Create a file named
164. ious menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word CN2610 User s Manual Redundant COM Selecting the Application Open Port Menu gt Mode to configure the Redundant COM application 1 From the MAIN MENU use the arrow keys to select Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter CNAS S m S270 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 NT Real COM ASPP Async Server Proprietary Protocol 02 NT Real COM ASPP Async Server Proprietary Protocol 03 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM 06 INT Real COM 07 NT Real COM 08 NT Real COM ASPP ASPP ASPP ASPP Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietar
165. is described in detail below the figure ICN2610 8 CN2610 3L Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed its Parity Fie RIS CTS XON XOFF Dascon ered 01 None yes None J 02 115200 None a yes None 03 RSZ OM None yes None 04 IAGAOO None yes None g5 TI5200 None j yes None 06 TT5200 None s yes None Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 115 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection CN2610 User s Manual Setting Up Device Control 4 Press ESC to return to the PORT MENU Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save q SERVER MENU Info Lan Adv Host_table Route_table Enter select ESC previous menu Warning fh You had modified the configuration without saving Would you save it now YY yes WIN B saio You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Ent
166. ixed TTY NT Real COM cccccccsccesssecesecesseecesseesseecnseeeeeeens 3 3 Device Control Device Control cccccccccessesssecescceescecesecesseeceeeesseeceaeeesseecsseeseseecseeesaeens 3 3 UDP Communication Raw UDP ccccccecssessccssecesseeceseeessceceeeeeseeceseeseseeceaeeeeseecseeeeaeees 3 4 Dual host Redundant Data Acquisition System DRDAS 0 eee eceeeeeeeseeeeteceeeeeeeeeeees 3 5 Redundant COM e E aiet er E E aa aa cou estes us ca sdbectanbcoddevanceavoed een lena cones 3 7 Console Management Reverse Terminal cessceceseceececeseceeececeseceeeeecaeeeeaeecseeseneees 3 8 Terminal Access Terminal sinisiin e E AEE SEEEN RRE i 3 9 Multi host TTY Multi host TTY enirar oani h iaa rE E E r 3 10 Dial in Out of Band Management Dialin out ccccesceeseeeeceseceeecenecaeeceeeeseeeneeneeeenees 3 11 Network Printer Printer nesrin enea a Re a EAEE e EEE 3 12 Multiplexor Access Multiplex ccs ceeeccssssesecseseecsseeecssecaeesecsessecsaeeecsaecaeeseesesereeaeeees 3 13 Setting Up Windows Real COM Linux Real TTY Unix Fixed TTV 4 1 Accessing the Console Utility nnne res ri ap a aa a EA EER r SEEE E E aTi 4 2 Selecting the Application scescesesoessesesereneeessnenensncucesosesenssssenvenenenenseseseveessennevenes 4 3 Chapter 5 Chapter 6 Chapter 7 Chapter 8 Chapter 9 Confisurmg ASPP Mod somesha enesest eter tired eon ean 4 4 Configuring the Serial
167. k the CN2610 will use its own IP address in which case you will need to specify different TCP port numbers for different serial ports Destination IP IP address The host with this IP address will have Optional addr exclusive access to this port If left blank all hosts on the network will have access to this port Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect TCP alive 0 99 minutes The time period the CN2610 waits before Optional check time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 5 7 CN2610 User s Manual Setting Up Device Control 4 Press Esc to return to the PORT MENU Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter CNA SSeS Server Port seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter VONE Line EE ena EEN OE a Examine modify asynchronous port configuration Enter select ESC previous menu 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item
168. l port gt Check to see if the RS 232 cable is wired correctly If the port is utilizing RTS CTS hardware flow control then the RTS CTS pins should be included In this case a cable with only TxD RxD and GND pins will not work gt The terminal may be unlocked by pressing Ctrl S Hex Code 0x13 if software flow control is used Press Ctrl Q Hex Code 0x11 to relieve it Saving the CN2610 s Parameters Question How can I save the CN2610 s parameters to recover from unexpected power failures or to transfer the same parameters to another CN2610 Solutions gt After entering the Console screen select seTting gt Export and press Enter Then you can use XMODEM for a Windows host or RCP for a UNIX host to save the parameters to a file Server Port SeTting sAve Utility Restart Exit Export Or MPO wcontiguration Enter select ESC previous menu CHAO POS S V20 Export Easo AES pmo O bom Export current configuration to file Enter select ESC previous menu A 5 CN2610 User s Manual Troubleshooting CNZ2610 3_ 19 V2 0 Export Esos a ES e NOE Export current configuration to fille ESC back to menu Enter select Export via onsole port using XMODEM jj Host name IP address File name User name Press CIRL U tO Start s ASPP Port Problems Problem The application utilizing the ASPP subroutines could not connect to the CN2610 Solutions gt Check to see if the target por
169. l COM ASPR Async Server Proprietary Protocol 03 NT Real COM ASPP Async Server Proprietary Protocol 04 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM ASPP Async Server Proprietary Protocol m Jt 06 RTELNET Reverse Telnet mode 07 NT Real COM ASPP i Async Server Proprietary Protocol Configuring RTELNET Mode Reverse Telnet or RTELNET supports the Telnet program used by Ethernet hosts to login to serial hosts Ethernet hosts recognize serial ports by the specified source IP address or by the TCP port number followed by the CN2610 s IP address 1 Move the cursor to the Description more setting column and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 NT Real COM ASPP Async Server Proprietary Protocol 02 NT Real COM ASPP Async Server Proprietary Protocol 03 NT Real COM ASPP Async Server Proprietary Protocol 04 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM ASPP Async Server Proprietary Protocol 06 Reverse Terminal RTELNET Reverse Telnet mode O NT Real COM ASPE l Async Server Proprietary Protocol 2 The pop up selector contains input display fields for TCP port Source IP address Destination IP addr Inactivity time Map keys lt CR LF gt to Authentication type and T
170. l Local User Information Save Restart OOCOCOODKOUOCD CN2610 User s Manual Setting Up Dial in Out Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 12 2 CN2610 User s Manual Setting Up Dial in Out Selecting the Application Open Port Menu gt Mode to configure the Dial up out application 1 From the MAIN MENU selec
171. l Port 8 Specify the first COM port name your system will map to 1st COM name TYEE www moxa com a 11 For added security set a password for the CN2610 Check the Auto Saved box to save the password on your computer Click Next to continue Add Server Wizard Ea Welcome to Set Server Password NPort Server Pro ee ee Your system has no password protection It is strongly recommended that you set up a password to prevent misuse of the selected Server Server Password Confirm Password MV Auto Saved www moxa com lt Back Cancel 4 42 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 12 Check the new server settings to make sure they are correct and then click Finish Complete You have finished adding the following server to NPort Manager If the information is correct click on Finish to save these settings Model CN2510 8 Server Name CN2510 8_5631 Ports COM3 COM10 Server Serial Number 5631 Server IP 192 168 127 254 13 The server and ports will be displayed in the CN2610 Server Manager window Click the Save icon in the upper left corner to save the settings before exiting the program sA NPort Pro Manager Custom OP x elisa sla CN2510 8_5631 CN2510 8 Ready 7 Configuring the CN2610 in a Windows 95 98 ME NT Environment After the CN2610 driver is installed you can procee
172. ld like to configure and select Properties A Device Manager Display adapters DYD CD ROM drives Floppy disk controllers JB Floppy disk drives 3 IDE ATA ATAPI controllers D gt Keyboards Mice and other pointing devices Monitors Properties 2 Click the Configuration tab MOXA Async Server CN2510 8 Properties Use this device enable CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 3 Click Settings to configure the CN2610 s Basic Configuration Password and Access Control MOXA Async Server CN2510 8 Properties 2 x General Configuration Driver m NPort Server Async Server Status Model CN2510 8 IPAddress 192 168 127 254 Port Status COM Number COM13 COM20 Ports Setting OK Cancel 4 On the Basic Configuration page modify Server Name IP Address Netmask and Gateway Check the DHCP checkbox if the network parameters will be assigned automatically by a DHCP server Property Sheet i xi Basic Configuration Password Access Control Model Name CN2510 8 Serial Number 5631 Server Name IP Address 192 168 127 254 Netmask 255 255 255 O Gateway 5 4 20 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 5 On the Password page add a password or change the existing password Check the Remember Password checkbox to remember the password on this compute
173. lity For example the CN2610 application that corresponds to Linux Real TTY Unix Fixed TTY is NT Real COM mode The following topics are covered in this chapter Windows Real COM NT Real COM Linux Real TTY Unix Fixed TTY NT Real COM Device Control Device Control UDP Communication Raw UDP Dual host Redundant Data Acquisition System DRDAS Redundant COM Console Management Reverse Terminal Terminal Access Terminal Multi host TTY Multi host TTY Dial in Out of Band Management Dialin out Network Printer Printer Multiplexor Access Multiplex OOOCOCOOUO OOOCD CN2610 User s Manual Knowing Your Application Windows Real COM NT Real COM Windows 2000 Host A Windows 2000 Host B a PIEN I gt J a j g Bar Code POS Bar Code POS Bar Code POS Reader Terminal Reader Terminal Reader Terminal MOXA provides CN2610 COM port drivers for all Windows operating systems The COM port driver serves a dual purpose 1 convert serial data into Ethernet packets 2 convert Ethernet packets into serial data as outlined in the following table PC gt CN2610 gt Serial Device Serial Device gt CN2610 gt PC 1 The PC generates RS 232 serial COM 1 A serial device connected to the CN2610 commands starts transmitting serial data 2 The COM port driver converts the 2 The CN2610 converts the data into one or commands into Ethernet packets more Ethernet packets 3 The
174. ll be allowed for this serial port Terminal mode no Star NT 560 The CN2610 provides 3 modes that Optional NL 5000A depend on the connection mode VT100 supported by the terminal Inactivity time 0 99 minutes Idle time before the port is Optional disconnected automatically If set to 0 minutes the port will not disconnect TCP alive check 0 99 minutes The time period the CN2610 waits Optional time before checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection Session Hot Key Configure the Hot key TCP port TCP port and Remote IP address for each Remote IP session 3 Press Esc to return to the PORT MENU Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter CNA SLO S ES VZO Server Port seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter NODECEE Line Mpu lel jtee smeoreyi ma utc eum Oe bane Examine modify asynchronous port configuration Enter select ESC previous menu 11 5 CN2610 User s Manual Setting Up Multi Host TTY 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for
175. ll be interpreted as a disconnection 4 Press ESC to return to the PORT MENU Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save GNASILOS IS W20 ip obo an esoe A Os oE O o USer table Mebane Examine modify async server basic configuration Enter select ESC previous menu Warning You had modified the configuration without saving Would you save it now YY yes You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel Server Port seTting UE lie Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select 13 8 CN2610 User s Manual Setting Up Printer Restart 1 From the MAIN MENU select Restart lant Sane oh a ET Uh oni oe ME Y W emma Restart Mipene Restart the whole system or selected async ports Enter select ESC previous menu 2 Select System and then press Enter to restart the system and terminate the Telnet session CNZGILO 5 A9 V20 System EEZ Quit Restart the Async Server ESC back to menu Enter select Warning Lti Restart system will disconnect all ports and clear all status value Enter continue ESC cancel Setting up Unix Hosts UNIX uses the RLP program for remote parallel printing For serial printing MOXA provides the asprint utility program which consists of two fil
176. lt directory or click Browse to select an alternate location 1G Setup NPort Monitor Utility Select Destination Location Where should NPort Monitor Utility be installed i Setup will install NPort Monitor Utility into the following folder To continue click Next If you would like to select a different folder click Browse Atleast 1 1 MB of free disk space is required 4 Click Next to install the additional tasks you will perform 5 Click Next to proceed with the installation The installer then displays a summary of the installation options i6 Setup NPort Monitor Utility Select Additional Tasks Which additional tasks should be performed Select the additional tasks you would like Setup to perform while installing NPort Monitor Utility then click Next Additional icons 16 28 CN2610 User s Manual Administrative Utilities 16 Setup NPort Monitor Utility Ready to Install Setup is now ready to begin installing NPort Monitor Utility on your computer Click Install to continue with the installation or click Back if you want to review or change any settings Destination location C Program Files NPortM onitor Cancel 6 Click Install to begin the installation The setup window will report the progress of the installation To change the installation settings click Back and navigate to the previous screen 7 Click Finish to complete the installation of the CN26
177. lude unintentional technical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Chapter 1 Chapter 2 Chapter 3 Chapter 4 Table of Contents NERO QUIC TOM x dssccsentazcatestanssacnacasasusenavacaseesinastaaccusuinutsnasthaanensuaanduecnasscestens 1 1 Product FGatures incitas a tus E E E Woutih bovaue tun thous EE EN EE 1 2 la TRONEN AAA A A TE 1 2 STOI LAAen N EEE AE E E A E E E E E E E ESE 1 2 Package Checklist astenio nt ea a EE E E E EE E AE 1 2 Fr nt Panel i sis sci ce ivsis n uae shite a Be setae Hea R REA taie taa EE E ASEE E Abed 1 3 Rear eT EE EE A T edocs stuasvodacasdinpebsmeaveracsesSeavs 1 3 Bottom Lab le e E E A E E E 1 3 Getting Startede ee eee aaran 2 1 Hardware Installation a E E cease spostentaaddeasheashnibbeaetaess 2 2 Desktop ere nasr EE EE A E cence cea cette bytes e E E a OE TEA 2 2 Ra ackmo nt ans a E S BEEE AAEE AEE AAEE 2 2 Wiring Requirement eei e a aa A a a is Raven N aati Sii 2 3 Connecting the CN2610 8 16 s POWer ssssssesesssesseeeesesssrstsrerrererssrsrsrerreresesesrereerees 2 3 Connecting to the NetWork no piitan ey i ini iba caercetotenee anI eo teense a a EEEn 2 3 Connecting to a Serial Devicesin senper aa e a a E E 2 4 Connecting to the Console Port esessesseseeeesessstseeresrsssrstsretreretsesesreesesesrerreeeeees 2 4 Accessing the Console Utility s cpcsiss eh
178. m or mount t iso9660 ro mode 0555 lt device gt Example mount t iso9660 ro mode 0555 dev hdb mnt 3 Copy the file to the UNIX host cp mnt cdrom radius 2 3 tar Extract the tar to files radiu 2 3 subdirectory tar xvf radius 2 3 tar After extracting there are subdirectories as follows src source code conf configuration log log record temp temporary files bin execution files Compile and link cd sre sh mk_radius RADIUS Server Configuration gt Gonfiguration Monitor Daemon Control Report Others Specify password file Configuration gt Basic Configuration gt Password File etc passwd for LINUX etc shadow for SCO UNIX and SOLARIS etc master passwd fot FREEBSD and BSDI CN2610 User s Manual RADIUS Server 4 5 nn gt assword File etc passwd dmi etio Async Server A Save amp Exit 2 Specify the CN2610 s IP Configuration gt Basic Configuration gt Async Server Administration gt Add Async Server 4 Basic Configuration 4 Pa ord zd Save ER 4 4 Async Server Administration t te nn dd Async Server M lodtfy e server gt P Address Name
179. mation and configuration instructions 3 10 CN2610 User s Manual Knowing Your Application Dial in Out of Band Management Dialin out Web Server E mail Server TCP IP oe CN2610 P Router Modem gt S i PPP SLIP PPP Dialout Dialin Dialin Internet Modem k J a a UNIX Server PC Notebook The CN2610 provides dial up dial out access for ISPs and enterprises that need a remote access solution When a user at a remote site uses a PPP dial up connection to access the CN2610 the CN2610 plays the role of dial up server but also ensures the user has legal access to the network by verifying the user s identity with its Local User Table or RADIUS The CN2610 supports PPP SLIP and Terminal modes for dial up dial out access Regardless of which OS is used you will always be able to use standard PPP dial up to establish a connection The CN2610 can also act as an Async router to connect serial ports to a WAN connection Routing protocols including static RIP I and RIP II can be adjusted to route different WAN connections Refer to Chapter 11 for detailed information and configuration instructions CN2610 User s Manual Knowing Your Application Network Printer Printer TCP IP F CN2610 Printer Printer Printer Printer The CN2610 s printing program running under UNIX provides an excellent solution for banking and stock exchange services with huge printing demands Use a Windows or
180. mode parameters move the cursor to the Detail setting column to highlight PPP parameters and then press Enter Enable Detail setting TERM_BIN mode yes Term parameters PPPD mode MOi parancters SLIPD mode SLIP parameters 8 The pop up selector contains input display fields for Destination IP addr Source IP address IP netmask TCP IP compression Inactivity time Link quality report Outgoing PAP ID and PAP password Each item is described in detail below the figure Destination IP address Source IP address IP netmask TCP IP compression Inactivity time Link quality report Outgoing PAP ID PAP password Setting Value Notes Necessity Destination IP IP address for the You need to assign an IP address for the Required addr remote Dial in remote user Dial out user Source IP IP address for the The CN2610 will automatically assign Optional address port an IP address for the port We recommend leaving this space blank IP netmask IP netmask The CN2610 automatically assigns the Optional netmask 255 255 255 255 We recommend leaving this space blank 12 11 CN2610 User s Manual Setting Up Dial in Out Setting Value Notes Necessity TCP IP Yes No Depends on whether the remote user s Optional compression application requests compression Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If se
181. more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 NT Real COM ASPP Async Server Proprietary Protocol 02 NT Real COM ASPP Async Server Proprietary Protocol 03 NT Real COM ASPP Async Server Proprietary Protocol 04 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM ASPP Async Server Proprietary Protocol 06 NT Real COM ASPP Async Server Proprietary Protocol 07 NT Real COM ASPP Async Server Proprietary Protocol NT Real COM ASPP Async Server Proprietary Protocol 4 Use the Up Down arrow keys to select DRDAS and then press Enter CN26 105603 W250 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enters Port Application t ption more setting 01 DRDAS PC redundant data 02 DRDAS Dialin out PC redundant data 03 DRDAS Terminal PC redundant data 04 DRDAS Reverse Terminal PC redundant data 05 DRDAS Device Control PC redundant data 06 DRDAS Multiplex PC redundant data 07 DRDAS Printer PC redundant data 08 DRDAS Multi Host TTY PC redundant data 09 DRDAS NT Real COM IPC redundant data 10 DRDAS DRDAS REECE
182. more setting 01 02 03 04 05 06 07 08 Dialin out Dialin out Dialin out Dialin out Dialin out Dialin out Dialin out Dialin out Disable Dialin out Terminal Reverse Terminal Device Control Multiplex Term SLIP PPP Term SLIP PPP Term SLIP PPP Term SLIP PPP Term SLIP PPP Term SLIP PPP PERT Perr SLIP PEP MOS ES NT Real COM DRDAS Raw UDP Redundant COM 13 3 Term SLIP PPP l l identification identification identification identification identification identification identification identification CN2610 User s Manual Setting Up Printer 5 The Dialin out application supports two operation modes RAW PRN and LPD PRN RAW PRN mode is selected by default CNZ 60S ei 0 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Raw serial port printer mode NT Real COM Async Server Proprietary Protocol Configuring RAW PRN Mode 1 Move the cursor to the Mode column for the port and then press Enter CACO aL W510 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports
183. n ASCII Transmit Kermit XModem 1KCRC XModem CheckSum XModem cRC C Modem ZModem 8 Choose the backup filename CN2610 bak for example and then click Save ax Save in S WINXP F e fy c E Documents and Settings Program Files WINXP WUTemp Filename CN2501 bak Save as type e Cancel 9 The CN2610 will export settings to the file Z 16 34 CN2610 User s Manual Administrative Utilities Remote RCP Export As we pointed out earlier RCP is a file transfer protocol that does not require a password 1 Login to your UNIX LINUX host For example login to 203 67 8 22 as user john 2 Create a file named rhosts in this directory Enter the CN2610 s IP address e g 192 168 205 21 or the CN2610 s domain name if it s defined in your etc hosts file in the rhosts file Telnet the CN2610 s IP address After entering the CN2610 s MAIN MENU select setting gt Export In the Export via column select Network host using RCP Enter the UNIX LINUX host s IP address for Host name IP address Enter the CN2610 s firmware file name on the UNIX LINUX host for File name Enter the user name required to login to the UNIX LINUX host for User name Press CTRL U to start Import Default Quit Export current configuration to file Cer NNO FS amp ESC back to menu Enter select Network host using RCP AOS oO ato 22 home john CN2610 rom john
184. n The time period the CN2610 waits before Optional checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 5 Press Esc to return to the PORT MENU Configuring RAW Mode RAW mode is used for standard TCP IP socket programs RAW mode provides a transparent communication link between the network socket program and the corresponding serial port 1 Move the cursor to the Mode column for the port and press Enter CZE O aes ye O Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting omi oe Og Real COM 04 NT Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol 05 NT 06 07 Real COM Async Server Proprietary Protocol Device Control Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol CN2610 User s Manual Setting Up Device Control 2 Use the arrow keys to highlight RAW and then press Enter cN2610 8 CN2610 8_19 v2 0 Mode Line mOdem Welcome _MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Async Server Propr
185. n Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Esc Key Shortcut Key Capitalized letter of the word 10 2 CN2610 User s Manual Setting Up Terminal Selecting the Application Open Port Menu gt Mode to configure the Terminal application 1 From the MAIN MENU select Port and then press Enter Server xeeet seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous men
186. n mode of async ports ESC back to menu Enter select POCE 01 02 03 ee are NT Real COM NT Real COM NT Real COM 04 NT Real COM 05 NT Real COM 06 pial in out N N Description more setting Async Server Proprietary Server Proprietary Server Proprietary Async Server Proprietary Protocol pene Soe Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol Protocol Protocol meine P OLOCO 07 Real COM 08 Real COM The pop up selector contains input display fields for Destination IP addr Source IP address IP netmask TCP IP compression Inactivity time Link quality report Outgoing PAP ID PAP password and Incoming PAP check Each item is described in detail below the figure Destination IP addr Source IP address IP netmask TCP IP compression minutes Inactivity time Link quality report Outgoing PAP ID PAP password Incoming PAP check Setting Value Notes Necessity Destination IP IP address for the Assign an IP address for the remote user Required addr remote Dial in Dial out user Source IP IP address for the The CN2610 will automatically assign Optional address port an IP address for the port We recommend leaving this space blank IP netmask IP netmask The CN2610 automatically assigns the Optional netmask 255 255 255 255 We recommend leaving this space blank TCP IP Yes
187. n samen 6 2 Selecting th Applications anaana d nao Mi ea ek i bers a aa 6 3 ConfigurinsyRAW UDP Mode visecscssstsccassscpssedescnsssevesesssteibsssesieidiSnasnevenssoutasthssazoxencostsbesss 6 4 Configuring the Serial Ports iyeon in n E E E NE Ee 6 6 E E E casbuescepudsecpesvesesseaya sovecusausebssbaneseeees 6 7 ROStart senesan weet i Sees oer a aeae ENEA EE Eie KEE ESE ETES EEEo EEVEE E VEE RESE 6 7 Setting Up the Dual host Redundant Data Acquisition System 7 1 Accessing the Console Utility 00 cece cececssecscesecnereecssseecaecaessecaeesecsaeeesascasesecaesseenaeeneegs 7 2 Sel cting the Applications sco ttvcresiecsen ohievt stewie a a e E E a es 7 3 Configuring DRDAS Mode ee ccesecssesecseesecseseecsscsseecesaecsessecaeesecnaeeecsaecaeesecnesseenaeeeeeas 7 4 Configuring the Serial Ports nesihet reris vs aust coptesty cd week aeeie ENEE Ea Sp rented eats 7 5 DAVES escent Aili ise Gaia ain he Si in ae ate RS 7 7 Restart onenean anar a r soieeaotu canes Sued ine tvecintadaes a E A eaeoepeces 7 7 Setting Up Redundant COM Mod ccsssseecceeseeeeeeeeeeeeeneeeeeeeeeneneeeees 8 1 Accessing the Console Utility sisse terc nre oE e EE EE EEE EET EEEE aee 8 2 Selecting the Application soron tenier a E I E N E 8 3 Configuring Redundant COM Mode ces ssssecsseecsseeecesecseeseceeesessecseesecsaeeeesaeeaesseeneeats 8 4 Configurins the Serial Portsin jo sstschiecsetesssspaticesdvassseto ieee vai e E EEA EA E EEEE E aE ines 8 7
188. nServer make sco SCO UnixWare make svr5 UnixWare 2 1 x SVR 4 2 make svr42 Configuring tty Redirection The following example illustrates how to map and redirect a tty device to a MOXA CN2610 serial port Use vi or any other text editor to add or modify entries in the file moxattyd cf There are three columns Device Name CN2610 IP address and TCP port number in the entry for the file moxattyd cf NOTE Device Name CN2610 IP address TCP Port number ttyp1 192 168 1 1 4001 ttyp2 192 168 1 1 4002 ttyp3 192 168 1 1 4003 ttyp4 192 168 1 1 4004 1 Device Names for SCO OpenServer are ttyp n for SCO UnixWare SVR4 2 are pts n The value of n should be equal or larger than 11 to prevent from conflicting with the device names of functional keys in some UNIX systems Default TCP port numbers are from 4001 to 4016 for the 16 port CN2610 If necessary you can customize the TCP port numbers However the numbers you use MUST be the same as those defined in the CN2610 11 8 CN2610 User s Manual Setting Up Multi Host TTY Adding Fixed TTY driver to system booting procedures To include Fixed TTY driver in the booting system add the moxatt yd daemon process to the etc inittab file The following example illustrates how to add the full path name for moxattyd to the entries of etc inittab ts 2 respawn usr etc moxattyd moxattyd t 1 NOTE The option t 1 means the reconnection t
189. nc Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol N N T Real COM Async Server Proprietary Protocol T Real COM Async Server Proprietary Protocol T Real COM Async Server Proprietary Protocol Configuring ASPP Mode Follow these steps to configure ports for ASPP mode 1 Move the cursor to the Description more setting column and press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Async Server Proprietary Protocol 05 NT Real COM Async Server Proprietary Protocol 06 NT Real COM Async Server Proprietary Protocol 07 NT Real COM Async Server Proprietary Protocol 08 NT Real COM Async Server Proprietary Protocol 2 The pop up selector contains input display fields for TCP data port TCP command port and TCP alive check time Each item is described in detail below the figure Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application 01 Real COM TCP data PORR 02 Real COM TCP command port 03 Real COM TCP alive check time 04 Real COM 05 Real COM Async Server Proprietary Protocol 06 Real COM A
190. nd the Telnet Console session will terminate Enter the MAIN MENU again to check whether the settings have been changed 8 9 9 Setting Up Reverse Terminal In this chapter we show how to use the CN2610 to connect terminals to a computer over an Ethernet network The following topics are covered in this chapter Q Accessing the Console Utility QO Selecting the Application Configuring RTELNET Mode QO Configuring the Serial Ports Save Restart CN2610 User s Manual Setting Up Reverse Terminal Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action K
191. nectivity and whether a network host is active 1 From the MAIN MENU select Utility and then press Enter Server Port seTting sAve Utility Restart Exit Async server utilities Enter select ESC previous menu 2 From the UTILITY MENU select Ping and then press Enter CNA GA Ping enuos oe iet CEOE a Ping e NASE Enter select ESC previous menu 3 Enter the target host IP address or target host name and then press Enter CN2OT0 22a v2 0 Ping Bie Wehehheteh ame Oe oe aero CEOE a Ping a host ESC back to menu Enter select Press ESC to cancel y PENG ALS AN bers Gal a Sie Voie Yeleneyer SS 64 bytes from 192 168 1 3 icmp_seq 0 64 bytes from 192 168 1 3 icmp_seq 1 64 bytes from 192 168 1 3 icmp_seq 2 4 Press Esc to return to Ping Monitor The Monitor utility allows you to monitor serial line status Line network status Network serial transmission flow Async async Setting routing and PPP trace 1 From the MAIN MENU select Utility and then press Enter Ces E S wy oy Server Port seTting sAve Utility Restart Exit Async server utilities Enter select ESC previous menu 2 From the UTILITY MENU select Monitor and then press Enter CN2610 8_19 V2 0 Ape Monitor EEEn oia CEOE o Monitor async server status Enter select ESC previous menu 16 2 CN2610 User s Manual Administrative Utilities 3 Each item is discussed in the following subsections
192. network to access the CN2610 s serial ports Redundant COM mode allows users to set up a highly redundant structure This chapter introduces the APIs for the following functions Q Accessing the Console Utility QO Selecting the Application Configuring Redundant COM Mode QO Configuring the Serial Ports Save Restart CN2610 User s Manual Redundant COM Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 Server Port seTting sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to prev
193. ng file near the bottom of the screen click the Port Manager menu Profile Edit PortManager Window Help a ikl E a Ble 3l22 Export Esna Default Quit configuration from previously saved file yack to menu Enter Import via Host name IP address File name User name Press CTRL U to start Start loading file 6 Select Port Manager gt File Transfer from the menu Comm Terminal Fmulator COM1 115200 None 8 1 T100 di Port Manager JWindow Help Open Ctrl Alt o Close Ctrl Alt L Close All Ctrl Alt A Port Enable Gtr AItHE v2 0 Port Disable Ctrl Alt Q Properties Send Pattern Send Break Capture Double Byte Character Press CTRL U to start Start loading file 16 37 CN2610 User s Manual Administrative Utilities 7 Inthe File Transfer window select XModem CheckSum for Protocol and Transmit for Direction This causes the file to be sent from the terminal to the CN2610 Click OK File Transfer Protocol Direction C ASCII Kermit Receive XModem 1KCRC C XModem CRC C YModem ZModem Cancel 8 Choose the backup filename CN2610 bak for example and then click Open Look in sowINXPF ma ea Documents and Settings Program Files WINXP WUTemp File name Jon251 O bak Files of type E 7 Cancel 9 The CN2610 will import settings from the file Remote
194. nmpInBadCommunityNames UdpLocalAddress tcpActiveOpens snmpInASNParseErrs UdpLocalPort tcpPassiveOpens snmpInTooBigs tcpAttempFails snmpInNoSuchNames Address Translation MIB tcpEstabResets snmpInBadValues AtlfIndex tcpCurrEstab snmpInReadOnlys AtPhysAddress tcpInSegs snmpInGenErrs AtNetAddress tcpOutSegs snmpInTotalReqVars tcpRetransSegs snmpInTotalSetVars tcpConnState snmpInGetRequests tcpConnLocalAddress snmpInGetNexts tcpConnLocalPort snmpInSetRequests tcpConnRemAddress snmpInGetResponses tcpConnRemPort snmpInTraps tcpInErrs snmpOutTooBigs tcpOutRsts snmpOutNoSuchNames snmpOutBad Values snmpOutGenErrs snmpOutGetRequests snmpOutGetNexts snmpOutSetRequests snmpOutGetResponses snmpOutTraps snmpEnableAuthenTraps C 2 D Pin Assignments and Cable Wiring In this appendix common pin assignment and cable wiring diagrams are presented The following topics are covered in this appendix Q Pin Assignments gt 10 100BaseTX Port Pin Assignment gt Console Port Pin Assignment gt Async RS 232 Port Pin Assignment QO Cable Wiring gt 10 100BaseTX Port Cable Wiring gt Async RS 232 Port Cable Wiring gt DB9 and DB25 Connector Pin Assignments CN2610 User s Manual Pin Assignments and Cable Wiring Pin Assignments 10 100BaseTX Port Pin Assignment Pin Signal 1 TX 2 Tx 3 Rx 6 Rx Console Port Pin Assignment I 5 RS 232 DSR in RTS out GND TxD out RxD in DCD in CTS in DTR out
195. nted aa a a i RS 14 3 Configuring the Host CN2610 sssssessesesssesisesresesrsrsrertererssrsesretssesesrereereessesrsrerernenes 14 3 Configuring the Device CN2610 oo cieeceessssscseseecsseeeesseceeesecnevsecsaeeecsaecaeesecneeseenaenees 14 7 Configuring the Serial Ports 000 ceeecssscseeccssecseesecseesecneeeecsaeceeaecseesesaesaeeseeneseenaeeees 14 11 SAVE ssi EE EA A E S A suueoaneetndsdeel A E 14 12 Res a Rh a aes 14 13 Setting Up Routing ss sssssnnnnnennnnnrnnnnnnnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnn eee 15 1 Accessing the Console Utility m sessccscccuhseveresccten ap siea hae a eirio eR Ea 15 2 What is RIP penes o ia iee E Rid ie ns AR is A ei BR aati 15 3 Conti suring RIP Biss esses pices eeaeee ee aa aa vodaeed Sates ae ee a ee ee sore 15 3 Configuring the Static Routing Table eee eeeccesecseesecneeeeceseeeesaecaeesecaecaeesecnererenaeenes 15 4 Static Routing Examples sarimi e r aa a r aeri 15 5 Configuring Routes to the Internet sseeeeeseseseeeseeeterssssrserrerrererssrsrsrerrsrsesrerreree 15 5 Configuring Routes to the Internet and Intranet ee ee eeceteereeteceeeeeneeeeeeaees 15 6 Configuring Multiple Point Routes es eessecseesecseceeceeeeecsaeeeeeseceeeseeeeseeeeens 15 7 DAV Gres ed ara a a a coms dex bateendembadeebeataneduage nevsuetheasn uncer E 15 8 REStaftisc cil hvh eth nena lel Gh aided al eh he hel iain eae es 15 8 Administrative UTES ois ii cede cnsdcinateenisssnassieecondenascedssnadendadewsauanene
196. nter Port LPT1 f lt 6 lt Sound video and aame controllers zl 4 33 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 2 Click the Configuration tab MOXA Async Server CN2510 8 Properties 2x General Configuration Driver ali MOXA Async Server CN2510 8 Device type Multi port serial adapters Manufacturer Moxa Technologies Co Ltd Location Unknown r Device status This device is working properly IF you are having problems with this device click Troubleshooter to start the troubleshooter Device usage Use this device enable 3 Click Settings to configure the CN2610 s Basic Configuration Password and Access Control MOXA Async Server CN2510 8 Properties ax General Configuration Driver m NPort Server Asyne Server Status Model CN2510 8 IPAddress 192 168 127 254 Port Status COM Number COM2 COM34 Ports Setting 4 34 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 4 On the Basic Configuration page modify Server Name IP Address Netmask and Gateway Check the DHCP checkbox if the network parameters are assigned automatically by a DHCP server Property Sheet xj Basic Configuration Password Access Control Model Name CN2510 8 Serial Number 5631 Server Name IP Address 192 168 127 254 Netmask 255 255 255 0 Gateway
197. ntrol NT Real COM Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol After configuring a port for the Device Control application you will need to choose between one of two operation modes ASPP and RAW ASPP mode which was developed by MOXA provides an easy to use TCP IP socket programming library and other useful functions Choosing RAW mode gives you more freedom to define your own applications for serial data transmitted and received over the Ethernet If you select RAW mode you will need to use standard TCP IP socket programming techniques Configuring ASPP Mode MOXA ASPP is a TCP IP socket programming library If you are using MOXA ASPP to create your programs configure the CN2610 s serial ports for ASPP mode and copy the ASPP library to the server ASPP programming functions and examples are introduced at the end of this chapter Each physical ASPP port is divided into two logical ports One is called the command port and the other is called the data port The command port is used to issue commands across the network to set the transmission line s configuration parameters such as baudrate data bits flow control condition etc The data port is used for normal data transmission tasks such as retrieving data from the serial device Follow these steps to configure ports for ASPP mode 1 Move the cursor to the Mode column for the port and press Enter CNAG S IS VATO
198. on your CN2610 are set to Real COM mode when mapping COM ports with CN2610 Windows Driver Manager 1 Go to Start gt CN2610 Windows Driver Manager gt CN2610 Windows Driver Manager to start the COM mapping utility 2 Click the Add icon ioj File COM Mapping View Help i RI A a a Exit Add Remove Apply Undo Setting No COMPot IPAddhess 1 IP Address 2 16 19 CN2610 User s Manual Administrative Utilities 3 Click Rescan to search for CN2610 async servers From the list that is generated select the server to which you will map COM ports and then click OK 192 168 324 219 O0 90 E8 10 81 68 192 168 36 219 J Mapping Redundant COM 1st Command Fort otal Forts Alternatively you can select Input Manually and then manually enter the CN2610 s IP Address 1st Data Port 1st Command Port and Total Ports to which COM ports will be mapped Click OK to proceed to the next step Note that the Add CN2610 page supports FQDN Fully Qualified Domain Name in which case the IP address will be filled in automatically 192 168 127 254 192 168 12 254 Fe _ x coe 16 20 CN2610 User s Manual Administrative Utilities 4 COM ports and their mappings will appear in blue until they are activated Activating the COM ports saves the information in the host system r
199. operly connected to a 10 Mbps Ethernet network 1 8 2 3 CN2610 User s Manual Getting Started Connecting to a Serial Device Use appropriately wired serial data cables to connect serial devices to the CN2610 s serial ports Connecting to the Console Port A console is a combination of keyboard and monitor that is used to configure settings and monitor the status of your system The console port can be used if a network is unavailable or you do not know the CN2610 s IP address To connect to the console port use a PC running UNIX or a PC with terminal emulation software e g HyperTerminal or PComm by MOXA parameter settings are baudrate 115200 bps parity check None data bits 8 stop bits 1 terminal type VT100 Use an RJ45 to DB25 or RJ45 to DB9 cable to connect the terminal to the console port Accessing the Console Utility The Console Utility is the main application used to set up the server configure the ports and run utilities ping diagnosis monitor and upgrade There are two ways to access the Console Utility with terminal emulation from a console terminal or with Telnet from a network terminal NOTE If your network is already set up telnet over the network to the CN2610 s IP address to access the Console Utility If your network environment is not set up use MOXA PComm Terminal to establish a direct serial console connection Configuration Checklist You will need the followin
200. oprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Server Proprietary Protocol 05 NT Real COM pete Server Proprietary Protocol UG 06 Device Control sync Server Proprietary Protocol 07 NT Real COM Async Server Proprietary Protocol 4 The pop up selector contains input display fields for TCP data port TCP command port and TCP alive check time Each item is described in detail below the figure Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Ok Real COM TCP data port 02 Real COM TCP command port 03 Real COM TCP alive check time 04 Real COM 05 Real COM Async Server Proprietary Protocol 06 Device Control Async Server Proprietary Protocol 07 Real COM Async Server Proprietary Protocol 5 5 CN2610 User s Manual Setting Up Device Control Setting Value Notes Necessity TCP data port 950 965 The host uses this value to determine Required which serial device to send data to These values are fixed and cannot be changed by the user Serial Port TCP Port No 01 950 02 951 03 952 16 965 TCP command port 966 981 The host uses this Port value to Required determine which device to send commands to These values are fixed and cannot be changed by the user Serial Port TCP Port No 01 966 02 967 03 968 16 981 TCP alive check time 0 99 mi
201. orer x Favorites gt NPort Server Pro Startup AY Documents gt DBooks Online MB Command Prompt E Settings gt OQWindows NT Explorer a Find gt BAdministrative Tools Common gt ee S HyperSnap DX Help Startup n as 40 4 amp Internet Connection Services for RAS gt pl Bun Int en B Internet Informati S Microsoft NNTP Service LS Microsoft Transaction Server amp Log Off Administrator S Microsoft oe EENE i Internet Service Manager HTML Ry Shut Down Product Documentation Release Notes Windows NT 4 0 Option Pack Setup Windows NTSe 2 Click Console Root gt Internet Information Server in the left info window Your computer s name will be visible 3 Click your computer name after which you will see RADIUS in the right info window fi Microsoft Management Console iis Console Root Internet Information Server rats BE Ea f Console Window Help laj xl ae Ene 7 Action 7 View X o l ar ey 8 Name Pah o y I Console Root B A Intemet Information Server Web site Administration Web Site 288 Default SMTP Site Default NNTP Site H A Microsoft Transaction Server Done Iz CN2610 User s Manual RADIUS Server 4 Right click RADIUS in the left info window and then select Properties ti Microsoft Management Console iis Console Root Internet Information Server rats olx 12
202. ort and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter CNAS S m S270 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Lk WA Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real COM Async Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Xt LO Async Server Proprietary Protocol 04 Real COM Async Server Proprietary Protocol G5 Real COM Async Server Proprietary Protocol 06 INT Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol CNAE LO 3 ES VZO Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter Port Application ption more setting O01 Real COM 02 Real COM Dialin out 03 Real COM Terminal 04 Real COM Reverse Terminal 05 Real COM Device Control 06 Real C
203. ort seTting sAve Utility Restart Exit Examine modify async server node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Bey Return to previous menu or Close pop up selector Ese Sey Shortcut Key Capitalized letter of the word 4 2 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Selecting the Application Open Port Menu gt Mode to configure the NT Real COM application 1 From the MAIN MENU select Port and then press Enter CN2610 8_19 V2 0 Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real COM As
204. otocol 04 T Real COM Async Server Proprietary Protocol 05 T Real COM Async Server Proprietary Protocol NT Real COM i Async Server Proprietary Protocol Async Server Proprietary Protocol N N N N N N N Async Server Proprietary Protocol NT Real COM NT Real COM Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application t ption more setting 01 Real COM Server Proprietary Protocol 02 Real COM Dialin out Server Proprietary Protocol 03 Real COM Terminal Server Proprietary Protocol 04 1X t LO Reverse Terminal Server Proprietary Protocol 05 Real COM Device Control Server Proprietary Protocol 06 Real COM Multiplex Server Proprietary Protocol 07 Real COM Printer Server Proprietary Protocol 08 Real COM Server Proprietary Protocol NT Real COM DRDAS Raw UDP Redundant COM 11 3 CN2610 User s Manual Setting Up Multi Host TTY 5 The only operation mode associated with this application is FIXTTY mode which is selected automatically in the Mode column CMZ 60 Se 19 V20 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real Async Server Proprietary Protocol NT Real Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Async
205. ou aql have a disk that contains the driver you want to install click Have Disk MOXA Async Server CN2516 MOXA Async Server CN2610 16 4 MOXA Asyne Server CN2610 8 MOXA DE 309 16 C0N2116 MOYA NC INA OIMN zl A This driver is not digitally signed Have Disk Tell me why driver signing is important lt Back Cancel 4 12 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 12 The Wizard will start installing the driver and automatically search the network for copies of the CN2610 model you selected in the previous step Add Hardware Wizard The wizard is ready to install your hardware Fates Hardware to install SK MOXA Async Server CN2610 8 To start installing your new hardware click Next Cancel 13 Although the next window to open states that the software hasn t passed Windows Logo testing you can rest assured that this driver has already been tested and been shown that it can support this Windows OS Click Continue Anyway to proceed Hardware Installation 4 The software you are installing for this hardware e MOXA Async Server CN2610 8 has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the corect operation of your system either immediately or in the future Microsoft strongly recommends that you s
206. pInErrors SysUpTime ifDescr ipInreceives IcmpInDestUnreachs SysContact ifType ipInHdrErrors IcmpInTimeExcds SysName ifMtu ipInAddrErrors IcmpInParmProbs SysLocation __ ifSpeed ipForwDatagrams IcmpInSrcQuenchs SysServices ifPhysAddress ipInUnknownProtos IcmpInRedirects ifAdminStatus ipInDiscards IcmpInEchos ifOperStatus ipInDelivers IcmpInEchoReps ifLastChange ipOutRequests IcmpInTimestamps ifInOctets ipOutDiscards IcmpTimestampReps ifInUcastPkts ipOutNoRoutes IcmpInAddrMasks ifInNUcastPkts ipReasmTimeout IcmpOutMsgs ifInDiscards ipReasmReqds IcmpOutErrors ifInErrors ipReasmOKs IcmpOutDestUnreachs ifInUnknownProtos __ ipReasmFails IcmpOutTimeExcds ifOutOctets ipFragOKs IcmpOutParmProbs ifOutUcastPkts ipFragFails IcmpOutSrcQuenchs ifOutNUcastPkts ipFragCreates IcmpOutRedirects ifOutDiscards ipAdEntAddr IcmpOutEchos ifOutErrors ipAdEntIfIndex IcmpOutEchoReps ifOutQLen ipAdEntNetMask IcmpOutTimestamps ifSpecific ipAdEntBcastAddr IcmpOutTimestampReps ipAdEntReasmMaxSize IcmpOutAddrMasks IpNetToMedialfIndex IcmpOutAddrMaskReps IpNetToMediaPhysAddress IpNetToMediaNetAddress IpNetToMediaType IpRoutingDiscards CN2610 User s Manual SNMP Agent with MIB Il UDP MIB TCP MIB SNMP MIB UdpInDatagrams tcpRtoAlgorithm snmpInPkts UdpNoPorts tcpRtoMin snmpOutPkts UdpInErrors tcpRtoMax snmpInBadVersions UdpOutDatagrams tcpMaxConn s
207. packets are sent over the network to 3 The packets are sent over the network to the CN2610 s Ethernet port the PC host s Ethernet port 4 The CN2610 converts the Ethernet packets 4 The COM port driver converts the back into RS 232 serial format Ethernet packets back into RS 232 serial 5 The commands are delivered to serial format device s connected to the CN2610 s serial 5 The serial data is processed by the program port s that controls the serial device You can enhance your applications greatly by using the CN2610 to access serial devices over an Ethernet network and since the CN2610 and the COM driver handle all protocol conversion tasks you won t need to modify the software currently in use In fact multiple PCs can access the serial ports of one CN2610 as shown in the figure Refer to Chapter 4 for detailed information and configuration instructions 3 2 CN2610 User s Manual Knowing Your Application Linux Real TTY Unix Fixed TTY NT Real COM A i Linux Unix i Ethernet ttyS1 ttyS2 104 ttySN Real TTY drivers that control a CN2610 s serial ports are provided for Linux environments This means that the CN2610 can be used with existing Linux based applications that use multiport serial boards since the host PC will recognize CN2610 s COM ports as real TTY ports You can enhance your applications by using the CN2610 to access serial devices over an Ethe
208. pen Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter CN2610 8_19 v2 0 Server Port seTting sAve Utility Restart Exit Examine modify async server ports configuration NT NT NT NT Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter CN26 LOS LS VZ VONE Line EEO Sna EER OE a Examine modify asynchronous port configuration Enter select ESC previous menu 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item is described in detail below the figure CNAS S IS F270 Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter Port Speed its Parity RIS CTS XON XOFF D ECONA toned cpa None amp yes None 02 S200 None yes None 03 1S 200 None f yes None 04 KISZA None i yes None 05 15200 None i yes None 06 ISZQO None i yes None Oy 115200 None yes None 08 T5200 None f yes None PRPRPRPRPRPRE l l l 14 11 CN2610 User s Manual Setting Up Multiplexor Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 1 1 5 2 Stop bits Parity None Even Odd
209. perly 8 6 CN2610 User s Manual Redundant COM Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU use the arrow keys to select Port and then press Enter Server sAve Utility Restart Exit Examine modify async server ports configuration seTting Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter CHAGAS re VAO WOCE Line EEO ena E ENCO a Examine modify asynchronous port configuration Enter select ESC previous menu 3 Specify the relevant settings Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed Stop Pari FEE RIS CTS XON XOFF Discon curl 01 Al None yes None oy TT5200 1 None yes None 03 115200 AJ None yes None 04 S200 ale None yes None 05 115200 al None yes None 06 aio 200 1 None yes None 07 115200 Al None yes None 08 115200 il None yes None 09 TT5200 ih None yes None 10 T15200 ak None yes None AA DESO dh None yes None T2 KISZQO dl None yes None ALS 15200 1 None yes None 14 aio WA0 0 alt None yes None ALS S2 OO 1 None yes None RG ILLS 20 all None yes None Setting Value Notes Speed 50 to 921 6 Kbps Transmission speed Bits 5 6 7 8 Data bit Stop 1 1 5 2 Stop bit Parity None Even Odd Mark Spac
210. pork contiguration Enter select ESC previous menu 2 From the SETTING MENU select Default and then press Enter CN2 SETTING MENU soo aoa Default Eog Load the factory setting Enter select ESC previous menu 3 Press Enter to confirm that you wish to erase all settings and restore the default settings Press any key to cancel CN2610 doo a oa Default Mebane Load the factory setting ESC back to menu Enter select Enter to load factory setting other key to cancel 16 39 A Troubleshooting In this appendix we give solutions to various problems you may come across when using the CN2610 The following topics are covered in this appendix Console Terminal Problems Configuring Dual Ethernet Ports Terminal Port Problems Saving the CN2610 s Parameters ASPP Port Problems SLIP PPP Connection Problems RADIUS Problems OOCUOCCOD CN2610 User s Manual Troubleshooting Console Terminal Problems Problem No message is displayed on the console terminal Solutions gt Check to see if the terminal is set to 115200 bps 8 data bits no parity 1 stop bit gt Check to see if the RS 232 cable is wired correctly The console needs CTS DCD signals to trigger Refer to the Cable Wiring section in Appendix D gt The console may be blocked waiting for an event Press ESC to try unblocking Problem Garbage characters are displayed on the console terminal Solutions gt Ch
211. ports by Linux operating systems The CN2610 can be used for a variety of applications to make the serial ports accessible over an Ethernet but without the need to modify existing serial transmission software The Real COM driver provided by MOXA lets users treat networked serial ports the same as local serial ports The following topics are covered in this chapter Accessing the Console Utility Selecting the Application Configuring ASPP Mode Configuring the Serial Ports Save Restart Setting up Hosts gt Setting up Windows XP 2003 Hosts gt Setting up Windows 2000 Hosts gt Setting up Windows 95 98 ME NT Hosts OOOCvUoCdD CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter al Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below al Telnet 192 168 127 254 Server P
212. prompt Password prompt Login user name Login password Terminal type 2 enss Inactivity time 0 minutes Authentication type none TCP alive check time 8 minutes Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Xo qian Yo oy lakor h en oyal Mode Description more setting 01 Reverse Terminal RTELNET Reverse Telnet mode 02 Reverse Terminal RTELNET Reverse Telnet mode 3 Reverse Terminal RTELNET Reverse Telnet mode J 04 Reverse Terminal RTELNET Reverse Telnet mode S Reverse Terminal RTELNET Reverse Telnet mode Source IP address Destination IP addr Inactivity time Map keys lt CR LF gt to Authentication type TCP alive check time Setting up UNIX Hosts You can use your own RADIUS software to do this MOXA however provides a RADIUS program for UNIX To use the MOXA RADIUS Server extract radius 2 3 tar from the CN2610 CD All files are extracted to the radius 2 3 directory Installing the RADIUS Execution File 1 Login to the UNIX host and create a directory mkdir radius cd radius 2 3 bin CN2610 User s Manual RADIUS Server 2 Mount the CD ROM volume os Command SCO OpenServer mount f ISO9660 filemode 444 lt device gt Example mount f ISO9660 filemode 444 dev cd1 mnt Solaris x86 cdrom cdrom0 In the volume manager mounts the CD ROM on mount point Linux mount dev cdro
213. pters E Network adapters Other devices PCMCIA adapters Parte CO 2 1 PT 4 27 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 8 Click Have Disk to install from the CD and then click Next to continue Add Remove Hardware Wizard Select a Device Driver Which driver do you want to install for this device Z Select the manufacturer and model of your hardware device and then click Next If you aql have a disk that contains the driver you want to install click Have Disk Manufacturers Models MOXA NPort Server Lite DE 301 MOXA NPort Server Lite DE 302 MOXA NPort Server Lite DE 304 MOXA NPort Server Lite DE 331 MOXA NPort Server Lite DE 332 MOXA NPort Server Lite DE 334 MOXA MPart Server Pra NEINA Comtrol Corporation Digi International Equinox Systems Inc Moxa Technologies Co Ltd Specialix International Ltd Stallion Technologies Ej xi Have Disk omes 9 After locating the win2k folder select the driver file NPSERVER INF and then click Open Locate File 2 x Look in Sy wink ce a NPortTool x History E Desktop PN My Documents Ror an My Computer ry a File name NPSERVER z My Network P Files of type Setup Information inf 7 Cancel 4 28 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 10 Select the correct CN2610 model and then click Next to continue
214. r Property Sheet 4 21 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 6 The Access Control page allows you to set up access rights for each of the the CN2610 s ports Access right is assigned by IP address In the example shown here the netmask of 255 255 255 255 limits access to the listed IP address 192 168 6 16 To allow access to a group of IP addresses adjust the netmask accordingly To allow any IP address to access a port delete all IP addresses assigned to that port Property Sheet xj Basic Configuration Password Access Control View access control list by IP Address N2510 8_5631 192 168 127 254 192 168 127 100 255 255 255 255 Add IP Add Port Remove i Modify I Tip Delete All IP Address to Grant All Cancel 4 22 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 7 Click Modify to save all Property Sheet settings and return to the Properties Configuration page MOXA Async Server CN2510 8 Properties ie x General Configuration Driver m NPort Server Async Server Status Model CN2510 8 IPAddress 192 168 127 254 Settings Port Status COM Number COM13 COM20 Ports Setting OK Cancel 8 Click Ports Setting to configure the data transmission mode and FIFO for each COM port MOXA Async Server CN2510 8 Properties 21x Gen
215. r 2 From the SERVER MENU select Adv and then press Enter Itii Ad Host_table Route_table User_table Quit Examine modify async server basic configuration ESC back to menu Enter select RADTUS C SOSTVEr IN RADIUS key wig port s GAS As IONAS Enable RADIUS accounting SNMP community name SNMP trap server IP address Ethernet IP forwarding ROUtINI Pr rococo None TCP retransmission timeout SiO E A O OE SIO data transfer timeout Gar bole 5 0 L000 me 3 RADIUS settings RADIUS server IP RADIUS server IP address RADIUS key RADIUS password must be the same in the RADIUS server UDP port 1 2 Mode 1 An earlier but rather common setting is 1645 If you choose 1645 the authentication must be set as 1645 and accounting as 1646 in the RADIUS Server Mode 2 The latest setting is 1812 If you choose 1812 the authentication must be set as 1812 and accounting as 1813 in the RADIUS Server Enable RADIUS accounting yes no 4 Save and then restart the CN2610 Setting up Port Configuration RADIUS is effective for dial up services Apart from dial in services PPP SLIP Dynamic it also supports RADIUS settings in Terminal applications and Console Management application Dialin out Dynamic Mode Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 Dialin out DYNAMIC iA
216. r select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We first use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting OI T Real COM Async Server Proprietary Protocol 02 T Real COM Async Server Proprietary Protocol 03 T Real COM Async Server Proprietary Protocol 04 T Real COM Async Server Proprietary Protocol 05 T Real COM Async Server Proprietary Protocol 06 NT Real COM i Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol N N N N N l 07 N N T Real COM T Real COM Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enters Pork Application t ption more setting 01 Real COM 02 Real COM Dialin out 03 Real COM Terminal 04 Real COM Reverse Terminal 05 Real COM Device Control Server Proprietary Protocol 06 Real CO
217. r contains input display fields for TCP port Source IP address Destination IP addr Inactivity time Map keys lt CR LF gt to Authentication type and TCP alive check time Each item is described in detail below the figure Source IP address Destination IP addr Inactivity time Map keys lt CR LF gt to Authentication type TCP alive check time 14 5 CN2610 User s Manual Setting Up Multiplexor Setting Value Notes Necessity TCP port number Each of the CN2610 s serial ports is Optional mapped to a TCP port To avoid conflicts with the TCP port numbers for CN251 s other serial ports use the default values 4001 for port 1 4002 for port 2 etc Source IP IP address for Specify an IP address for this port for Optional address the port application purposes If left blank the CN2610 will use its own IP address in which case you will need to specify different TCP port numbers for different serial ports Destination IP IP address Assign a host IP address on the LAN for Optional addr exclusive port access If left blank all hosts on the network will have access to this port Map Keys CR LF CR LF When you enter the string lt CR LF gt the Optional lt CR LF gt to CN2610 will determine whether to send lt CR gt lt LF gt or lt CR LF gt Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect
218. r this device To close this wizard click Finish lt Back Cancel 1 After the CN2610 server driver has been installed Windows will notify you that new hardware has been found Select Install from a list or specific location Advanced and then click Next to continue Welcome to the Found New Hardware Wizard This wizard helps you install software for Moxa Port 0 C If your hardware came with an installation CD or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended ir d Click Next to continue lt Back Cancel 4 15 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 2 Select Include this location in the search and then click Next to continue Found New Hardware Wizard Please choose your search and installation options Rates Y Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed J Search removable media floppy CD ROM IV Include this location in the search F winxP x Browse C Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware cr 3 Although the ne
219. r this example assume that the PPP source and destination IPs of modems 1 2 3 and 4 are Source IP Destination IP Source IP Destination IP Modem 1 203 67 6 250 202 6 6 250 Modem 3 202 6 6 250 203 67 6 250 203 67 6 249 201 2 2 249 Modem 4 201 2 2 249 203 67 6 249 In this case you will need to add three entries to the routing table as shown below CN2610 8_19 V2 0 ab obmoPmlt lelee A Oa ROUte table MMUi pqmmer lolk memOlbbme Examine modify the routing table ESC back to menu Enter select Gateway Destination Netmask 203 67 6 254 O10 0 0 0 0 0 0 2032015 6 200 202 76 6 0 1259 299 2953 POS Eo 6 249 201m2 Abs 6 215 5 52155 15 7 CN2610 User s Manual Setting Up Routing Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save j SERVER MENU Iesous Oe oE Oo USer table Roti Examine modify async server basic configuration Enter select ESC previous menu Warning id You had modified the configuration without saving Would you save it now You may also save all settings from the MAIN MENU by selecting sAve and then pressing Enter Press Enter again to save and any other key to cancel Server Port seTting Utility Restart Exit Save current configuration to Flash ROM ESC back to menu Enter select Restart 1 From the MAIN MENU select Restart CNAE O S RIES oh al E oni oe S A R Restart Meipene Restart
220. rd Received RDiscard ErrHeader Received REchoReq REchoRply Received ErrHeader Received ErrHeader CurrEstab 0 oN Lo Oo a Sent ErrSum SDiscard Sent SNoRoute SDiscard ErrProto ErrA Addr Sent SEchoReq SEchoRply Sent C Re D S ta hot E a ER ND foe ErrPorts U foe Ov Sent ESCORES ReSent Opens ey Grey Ste ote oy S IS 1S ey i Ethernet statistics Received Total number of input datagram packets received from the Ethernet Sent Total number of output datagram packets delivered to the Ethernet PPP statistics Received Received IP datagram packets RDiscard Received but discarded IP datagram packets ErrSum Checksum error packets Sent Sent IP datagram packets SDiscard Sent but discarded IP datagram packets IP statistics Received Received IP datagram packets RDiscard Received but discarded PPP datagram packets ErrHeader Received but discarded IP datagram packets due to errors in IP headers SNoRoute Received IP datagram packets for wrong route ErrProto Locally addressed IP datagram packet received successfully but discarded for not matching one of TCP UDP ICMP protocols offered by CN2500 Sent Sent IP datagram packets SDiscard Sent but discarded IP datagram packets ErrAddr Sent datagram packet discarded for invalid destination IP address ICMP statistics Received Received packets of ICMP messages Sent Sent packets of ICMP messages REc
221. re should Setup place the program s shortcuts 16 17 CN2610 User s Manual Administrative Utilities 5 Click Next to proceed with the installation The installer then displays a summary of the installation options 5 Setup NPort Windows Driver Manager Ready to Install Setup is now ready to begin installing NPort Windows Driver Manager on your computer 6 Click Install to begin the installation The setup window will report the progress of the installation To change the installation settings click Back and navigate to the previous screen In Windows XP the installer will display a message that the software has not passed Windows Logo testing This is shown as follows H Software Installation Click Continue Anyway to finish the installation 16 18 CN2610 User s Manual Administrative Utilities 7 Click Finish to complete the installation of the CN2610 Windows Driver Manager iS Setup NPort Windows Driver Manager g m fej x Completing the NPort Windows Driver Manager Setup Wizard Setup has finished installing NPort Windows Driver Manager on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup IV Launch NPort Windows Driver Manager Using CN2610 Windows Driver Manager After you install CN2610 Windows Driver Manager you can set up the CN2610 serial ports as remote COM ports for your PC host Be sure the serial port s
222. re the wires are perpendicular at the intersection point NOTE Do not run signal or communication wiring and power wiring in the same wire conduit To avoid interference wires with different signal characteristics should be routed separately e You can use the type of signal transmitted through a wire to determine which wires should be kept separate The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together e Keep input wiring and output wiring separate e Where necessary it is strongly advised that you label wiring to all devices in the system Connecting the CN2610 8 16 s Power Connect the CN2610 s 100 240 VAC power line to its AC connector If the power is properly supplied the Ready LED will show a solid red color until the system is ready at which time the color changes to green Connecting to the Network Connect one end of the Ethernet cable to the CN2610 s 10 100M Ethernet port and the other end of the cable to the Ethernet network There are 2 LED indicators located on the top left and right corners of the Ethernet connector If the cable is properly connected the CN2610 will indicate a valid connection to the Ethernet in the following ways The top right corner LED indicator maintains a solid green color when the cable is properly connected to a 100 Mbps Ethernet network 1 8 The top left corner LED indicator maintains a solid orange color when the cable is pr
223. reads or writes data After a program uses this PurgeComm function the CN2610 driver will continue to query the CN2610 s firmware several times to make sure no data is queued in the CN2610 firmware buffer rather than just flushing the local buffer This design is used to satisfy some special considerations However it may take more time about several hundred milliseconds than a native COM1 due to the additional time spent communicating across the Ethernet This is why PurgeComm works significantly faster with native COM ports on the PC than with mapped COM ports on the CN2610 In order to accommodate other applications that require a faster response time the new CN2610 driver implements a new Fast Flush option By default this function is enabled If you have disabled Fast Flush and find that COM ports mapped to the CN2610 perform markedly slower than when using a native COM port try to verify if PurgeComm functions are used in your application If so try enabling the Fast Flush function and see if there is a significant improvement in performance The Serial Parameters page shown in the following figure shows the default settings when the CN 2610 is powered on However the program can redefine the serial parameters to different values after the program opens the port via Win 32 API lt COM Port Setting E Port Number 1 Port s are Selected Basic Settings Advanced Settings Serial Parameters Security F
224. rminal type 1 ansi uyt166 2 vt52 El I Local Echo T Block Cursor M VT TOD Arrows Fonts Buffer Size 25 Background Color A 3 CN2610 User s Manual Troubleshooting Configuring Dual Ethernet Ports Question The CN2610 has 2 Ethernet ports How do I configure these 2 Ethernet ports Should I set up the CN2610 s 2 Network Interface Cards in different networks or set 2 different IP addresses in the same NIC Solutions 1 MOXA strongly recommends the following connect 2 different LAN ports to 2 different physical networks as shown This is the BEST solution 192 168 0 1 192 168 1 1 192 168 0 X 192 168 1 X gt MOXA does not recommend that you setup 2 LAN ports in the same physical network and subnet You might encounter unpredictable outcomes We suggest that you connect 2 different NICs to different networks We do NOT recommend this type of connection 192 168 0 1 192 168 0 2 192 168 0 5 2 First connect the CN2610 s LANI and LAN to the same hub or switch Configure IP addresses as 192 168 0 1 and 192 168 0 2 and subnet as 255 255 255 0 3 Connect one of the hosts on the network to the same hub or switch and configure its IP address as 192 168 0 5 and subnet as 255 255 255 0 4 When you set up the CN2610 like this we assume that you expect the 2 NICs to be load balanced This generally means that both connections transmit at the same tim
225. rnet network but without needing to modify the software currently in use MOXA also provides Fixed TTY port drivers for Unix environments However the Linux Real TTY and Windows Real COM port drivers provide better control over serial port data transmission since you can control modem signals such as DTR DSR RTS and CTS The Unix Fixed TTY driver provides software reception and transmission through the CN2610 s serial ports but does not allow you to control the DTR DSR RTS and CTS modem signals Refer to Chapter 4 for detailed information and configuration instructions Device Control Device Control IBM SUN SCO UNIX sio_open sio_open sio_read sio_write TCP IP RTU The CN2610 Device Control application allows you to choose between two different operation modes ASPP and RAW 3 3 CN2610 User s Manual Knowing Your Application ASPP Mode For applications that require setting up communication parameters or controlling modem signals DTR RTS Break etc take advantage of MOXA s ASPP lib to simplify your programming tasks ASPP takes care of the more basic protocol level programming tasks and allows you to concentrate your energy on higher level application specific tasks RAW Mode To control device data transmission directly set the CN2610 for TCP RAW mode Device control applications can use standard Linux Unix
226. rompt is received Login user name Login ID Optional Login password Login Password Optional Terminal type ansi Terminal type for outgoing connection Optional 10 8 CN2610 User s Manual Setting Up Terminal Setting Value Notes Necessity Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect Authentication None local None Authentication is not required Optional type server local Check the ID stored in the User_table defined under the SERVER MENU Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information TCP alive check 0 99 minutes The time period the CN2610 waits before Optional time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 5 Press Esc to return to the PORT MENU Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter Che eS 0 Server xeame seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter VONE Line EEO ena EEN OE a Examine modify asynchronous port configuration Enter select ESC previous menu
227. roprietary Protocol NT Real COM DRDAS Raw UDP Redundant COM 10 3 CN2610 User s Manual Setting Up Terminal 5 TERM_ASC mode is selected by default Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 Real COM ASPP Async Server Proprietary Protocol 02 Real COM ASPE Async Server Proprietary Protocol 03 Real COM ASPP Async Server Proprietary Protocol 04 Real COM ASPP j Async Server Proprietary Protocol 05 Real COM TEASER Async Server Proprietary Protocol J i ll 06 TERM_ASC ASCII Termianl mode 8 sessions 07 NT Real COM ASPP Async Server Proprietary Protocol After configuring a port for the Terminal application you will need to choose between one of two operation modes TERM_ASC and TERM_BIN The default mode TERM_ASC short for Terminal ASCII supports 8 terminal sessions The other option TERM_BIN short for Terminal Binary only supports 1 session Configuring TERM_ASC Mode TERM_ASC supports 8 terminal sessions for each terminal Hot keys are used to switch between different sessions 1 Move the cursor to the Mode column for the port and press Enter CHE OSs ME ed Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more set
228. rver With RADIUS a network manager or ISP only needs to maintain a single central database against which all remote user authentication takes place This greatly eases the management burden associated with administering large numbers of Dial in users Client Server Architecture RADIUS is a type of client server software Communication servers such as the CN2610 play an active role whereas a RADIUS server is passive 1 When a remote host is connected to the CN2610 it is prompted to enter its user ID and password 2 After receiving the user ID and password the CN2610 sends the information to a defined RADIUS server Up to this point the remote user is still unable to access the network 3 The RADIUS server compares the user ID and password with its internal database and then uses the internet to respond either accepting or rejecting 4 If the CN2610 receives the accept message from the RADIUS server the remote user is allowed to enter the network Otherwise the CN2610 will wait for another try or terminate the connection when a specified time limit has been reached Setting up the CN2610 Setting up the RADIUS Server IP Address 1 From the MAIN MENU select Server and then press Enter CNZELOSbaT oS V 250 Server REZIA si cain oe mamt 9 0 4 Sa Oh ons el Ws oA 5X10 or al OID Go Examine modify async server node table configuration Enter select ESC previous menu CN2610 User s Manual RADIUS Serve
229. rver and then press Enter CN2610 8_19 v2 0 Server EZ aeoe MmE Y 0 4 Seen Oh ons i ls oh a C1 ota Oe E Examine modify async server node table configuration Enter select ESC previous menu 2 From the SERVER MENU select User_table and then press Enter CN2610 8_19 V2 0 SERVER MENU Eondon esou C anes elton er loNK Man Colbie mae lona mem USer table Rotis Examine modify async server basic configuration Enter select ESC previous menu 2 19 CN2610 User s Manual Getting Started 3 The User_table is used for local authentication for dial in out access The CN2610 User Table which holds information for up to 64 users is useful if you do not have an external RADIUS server for authentication The User_table page contains input display fields for Entry User name Password and Phone number CESOS Ss e226 iibeb open eso Xo hans Osi o Man Colbie mau loln mem USer table Mebane Examine modify the user password table ESC back to menu Enter select User name Password Phone number Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save ase Ne ip obo an esoe amen slol jummer lol Man Colla mae lolk mm USer table Mebane Examine modify async server basic configuration Enter select ESC previous menu Warning You had modified the configuration without saving Would you save it now Chee LOS S Vee 0 Server Port seTting Utility
230. rver Proprietary Protocol 02 NT Real COM j Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Proprietary Protocol 05 NT Real COM TERM_ASC rver Proprietary Protocol 06 Terminal TERM_ASC TERM _BINSM ESUE Eeti NEOS C CS RoE mae 07 NT Real COM trver Proprietary Protocol NT Real COM 3 CNAGIO Le VZO Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting om NT Real COM ASPE J Async Server Proprietary Protocol 02 NT Real COM ASPP Async Server Proprietary Protocol OS NT Real COM ASPP Async Server Proprietary Protocol 04 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM ASPP Async Server Proprietary Protocol 06 Terminal RMR inary Terminal mode 1 session ASPP Async Server Proprietary Protocol ASPP Async Server Proprietary Protocol 07 08 Real COM NT NT Real COM 10 7 CN2610 User s Manual Setting Up Terminal 4 The pop up selector contains input display fields for Quit key Auto link protocol Link by input IP Auto login prompt Terminal type Inactivity time Authentication type and TCP alive check time Each item is described in detail below the figure Quit key AULO lank prokoce Telnet TCP port Primary Host LP Link by input IP Secon
231. rver node table configuration Enter select ESC previous menu 2 From the SERVER MENU select Route_table and then press Enter C26 GSB S V2 0 Lan LONA O o ROUte table MMUi sqmer lolk memOlbame Examine modify the routing table Enter select ESC previous menu 15 4 CN2610 User s Manual Setting Up Routing 3 Use the tab and arrow keys to move the cursor to configure Gateway Destination Netmask and Metric Each item is described in detail below the figure CNZIGHO Soo WO gondo ann e N Oa o ROUte table RAIRE aar o EO Examine modify the routing table ESC back to menu Enter select Gateway Destination Netmask Metric Setting Value Notes Necessity Entry 01 32 A maximum of 32 entries are allowed Fixed Gateway XXX XXX XXX XXX The IP address of the next hop router Required Destination XXX XXX XXX XXX The host IP address or network address of Required the route s destination Netmask XXX XXX XXX XXX The destination network s netmask Required Metric 1 15 The number of hops from the source Required destination 4 Press Esc to return to the MAIN MENU Static Routing Examples Configuring Routes to the Internet f UNIX Server 203 67 6 1 f Ethernet 203 67 6 TCP IP CN2610 Console Server PA Router 203 67 6 253 rf 203 67 6 254 _ Modem S Internet P Modem XN pe O v O Notebook 1
232. rver node table configuration Enter select ESC previous menu Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Close pop up selector Ese Key Shortcut Key Capitalized letter of the word 5 2 CN2610 User s Manual Setting Up Device Control Selecting the Application Open Port Menu gt Mode to configure the Device Control application 1 From the MAIN MENU select Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Real COM Async Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Real COM
233. s compression Inactivity time 0 99 minutes Idle time before the port is disconnected Optional automatically If set to 0 minutes the port will not disconnect 11 Press Esc to return to the PORT MENU 12 12 CN2610 User s Manual Setting Up Dial in Out Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter CN26 LO Soe VAO VOEE Line Enoe ena se mereyul me isl Camm Olena Examine modify asynchronous port configuration Enter select ESC previous menu 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item is described in detail below the figure CNZE TO ES VZO Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed Stop Pari EEO RIS CTS XON XOFF DiEGO cor 01 dl None y yes None 02 175200 1 None amp yes None 03 115200 ad None f yes None 04 T15200 il None yes i None 05 115200 al None y yes None 06 145200 1 None amp yes j None 07 DES200 Y None s yes None 08 LIALS200 ald
234. s menu 16 32 CN2610 User s Manual Administrative Utilities 4 Select Console port using XMODEM for upgrade type and then press Ctrl U to start EJ PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a Gara slale 3 25 E COM1 115200 None 8 1 T100 lol x S CN2510 8_5631 V2 0 sC back to menu Export via WWetwork host using RCP Host name IP address File name User name Press CTRL U to start menu Profile Edit Port Manager Window Help a BIA elhel S2 Export via Con e port using XMODEM Host name IP address File name User name Press CTRL U to start Start loading file 16 33 CN2610 User s Manual Administrative Utilities 6 Select Port Manager gt File Transfer from the menu PComm Terminal Fmulator COM1 115200 None 8 1 T100 Profile Edil Port Manager _ indow Help p Open Ctrl Alt o Close Ctrl Alt L Close All Ctrl Alt A 8_5631 V2 0 Port Enable Ghrl AlE E Port Disable Ctrl Alt Q Properties rer de fonsole port using XMODEM Send Break Capture Double Byte Character Press CTRL U to start Start loading file 7 Inthe File Transfer window select XModem CheckSum for Protocol and Receive for Direction Selecting OK causes the terminal to receive settings from the CN2610 File Transfer m Protocol Directio
235. seeecesecseesecneeseesecneeeeenaeseeeae D 2 Cable Wiring aenn a a a E E N ES D 2 10 100BaseTX Port Cable Wiring eseeseeeeeeeeiesesrseseereereresrsrsrerrererrsesrsrerrersesrerrees D 2 Async RS 232 Port Cable Wiring eseseeeseeseseseresreeessrseseseerestssesereseeresereeseresreeese D 3 DB9 and DB25 Connector Pin Assignments ssesseseseseerereeiesesrsrsrrrrersrsrresrerreree D 4 LOM Display accessed Ae ee ee ate E 1 1 Introduction MOXA s CN2610 dual LAN async server is available in models with 8 or 16 asynchronous RS 232 ports and all models come with two 10 100 Mbps Ethernet LAN ports The CN2610 dual LAN async server is used to connect terminals modems printers and other asynchronous serial devices to LAN hosts The CN2610 complies with TCP IP and IEEE 802 3 specifications using standard Ethernet 10 100BaseT and twisted pair 10 100BaseTX cable as the data transmission medium The following topics are covered in this chapter Q Product Features gt Hardware gt Software Q Package Checklist QO Front Panel QO Rear Panel O Bottom Label CN2610 User s Manual Introduction Product Features Hardware Software Dual LAN ports auto detecting 10 100 Mbps Ethernet Surge protection for each serial port 4 MB RAM 2 MB Flash ROM Tx Rx LED for each serial port System Status LEDs Ethernet Status LEDs 8 or 16 RJ45 RS 232 serial ports with up to 921 6 Kbps transmission speed ASCI Binary termin
236. ser s Manual Administrative Utilities 3 On the Communication Parameter page select COM2 for Ports 115200 for Baudrate 8 for Data Bits None for Parity and 1 for Stop Bits Property 4 On the Terminal page select VT100 for Terminal Type and then press Enter Property gt Local Echo 16 10 CN2610 User s Manual Administrative Utilities 5 Type 1 to choose ansi VT100 terminal type and then press Enter to enter the MAIN MENU Ei PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a BFA e5 elon 32 BY COM1 115200 None 8 1 T100 RTS JAsync Server CNZ510 8 Console terminal type il ansi vtl00 2 vtSZ 1l 6 Use the following keystrokes to navigate the CN2610 s console utility Action Key Move Up Down Left Right Arrow Key or Tab Key Jump to next menu or Select item Enter Key Return to previous menu or Esc Key Close pop up selector Shortcut Key Capitalized letter of the word Upgrading through the Serial Console 1 From the MAIN MENU select Utility and then press Enter EJ PComm Terminal Emulator COM1 115200 None 8 1 T100 Profile Edit Port Manager Window Help a GFA 2 65 elon 32 ka 115200 None 8 1 T100 io x CN2510 8_5631 V2 0 Server Port seTting save MERS restart Exit Async server utilities SC previous menu 2 From the UTILITY MENU sele
237. specified in milliseconds and must be larger than 10 ms If you want to send a series of characters in the same packet the serial device attached to the CN2610 should send that series of characters during a time interval less than the Force Transmit timeout and the total length of data must be less than or equal to the CN2610 s internal buffer size The serial communication buffer size is 1 KB per port 3 Press ESC to return to PORT MENU 6 5 CN2610 User s Manual Setting Up Raw UDP Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter CN2610 8_19 Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter CZE LOS Bae eo NOCE Line Mipw lel jten smerey me Utsl Cum OE Examine modify asynchronous port configuration Enter select ESC previous menu 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item is described in detail below the figure CUZ GTO SB os V20 Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed Lis Parity FIFO RIS CTS XON XOFF Discom cer 01 J None yes
238. ste 16 1 PING nenns atin can E E melanie dian ouside nats ee saat a 16 2 Monitor senesan bade tiie aa ete oie Avie Renee atid edhe EEA e havea te awed 16 2 DATE R E EEE sth sabesseisbhststasbipascycostesch asbssasisdisistustbusaicosts ohssbecsuheataas 16 3 NGtWOrk yc0 Sissons MTR ei iad Aine aA ia ole hielo ARG Acer divi adie 16 4 ASYNG sssscstsuus assets E EE REEE EE eee eee mars 16 5 ROUTING 4 cia aA AR Rae e Aina a AN awa aa a hi Hanahan 16 6 PPP T TAC P E T 16 6 Dia SNOStle a e a r E E E E E eld ea ah 16 7 Upgrade vein sasevert n tpn Ea Eae E Ea EA AEE EEEE lon eepebap at anes vtec 16 8 Upgrading with the Windows Utility seseseeeeeeeeeeeeseseseerereresrsesrerrererssrsesrereerse 16 8 Consol T rmimal Upgrades isaret peate rea reaa EEE TE AEA es 16 9 Upgrading through the Serial Console ssssseseeseeeeeeesesrseseeereresersrsrerrererssrsreeee 16 11 Remote RCP Upgrade roti iinei op aroe hatte aE EE E REE E 16 14 Windows Driver Manager Utility ee ec eeccseeeecneeeeceseeeeeseceeesecseeseenaseecsaecaeesesneeseens 16 16 Installing CN2610 Windows Driver Manager eceeseceseecesecseeeeeseeeeeeeeneeees 16 16 Using CN2610 Windows Driver Managet ecceescsesscseeeceseceeecneeeeeaeeeeens 16 19 Windows Monitor Utility secetei ea e aE E canis doy ana anasi 16 27 Installing CN2610 NPort Monitor Utility seseseeeeseeeeeeeeeeereesrsrsrrrrereresrsrsrerreree 16 27 Using NPort Monitor Utility eseri ee ceeeccsseeeseceesecs
239. sync Server Proprietary Protocol 4 4 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Setting Value Notes Necessity TCP data port 950 965 The host uses this port number to Required determine which serial device to send data to These values are fixed and cannot be changed by the user Serial Port TCP Port No 01 950 02 951 03 952 16 965 TCP command port 966 981 The host uses this port number to Required determine which device to send commands to These values are fixed and cannot be changed by the user Serial Port TCP Port No 01 966 02 967 03 968 16 981 TCP alive check time 0 99 min The time period the CN2610 waits before Optional checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection 3 Press ESC to return to the PORT MENU Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter Server Port seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Line and then press Enter CNZ C6 UOSB MS V250 WOCE Line EEO ena EERO a Examine modify asynchronous port configuration Enter select ESC previous menu 4 5 CN2610 User s Manual Windows Real COM Linux Real TTY Uni
240. sync Server is that you want to install CN2510 8 5631 14 The next window reports that the driver was installed and port drivers will be installed next Click Next to continue MOXA NPort Server Installation NPort Servers Async Servers installation completed NPort Server Async Server is ready to install Port driver 4 31 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY Installing Ports 1 The ports will be installed automatically Click Finish to conclude the installation procedure move Hardware Wizard Completing the Add Remove Hardware Wizard The following hardware was installed MOXA Async Server CN2510 8 Windows has finished installing the software for this device To close this wizard click Finish lt Back 2 After the installation is complete you can check Ports COM amp LPT under Device Manager to verify that all of the ports were installed successfully 1 x Action View Floppy disk controllers 9 Floppy disk drives Sy IDE ATA ATAPI controllers Keyboards TA Mice and other pointing devices 3 Monitors Ji Multi port serial adapters Sy MOXA Async Server CN2510 8 S Network adapters A Ports COM amp LPT Communications Port COM1 F Communications Port COM2 F MOXA Communication Port 1 COM27 F MOXA Communication Port 2 COM28 F MOXA Communication Port 3 COM29 A MOXA Communication Port 4
241. t Async server name EN e OSSA Async server location Async server serial number 3 Domain server 1 IP address 192 168 1 16 Domain server 2 IP address WINS function disable fno l WINS server IP address i Console password Async server name The CN2610 uses this name to identify itself when requested by an SNMP station or UNIX host Use an ASCII string with maximum length of 40 characters for the name Spaces are allowed Async server location The CN2610 reports this location to the SNMP station when requested Use an ASCII string with maximum length of 44 characters for the location Spaces are allowed Async server serial number Each CN2610 Async Server is assigned a unique serial number before it leaves the factory The serial number cannot be changed Domain server 1 2 IP address A Domain Name Server is a network host that translates host names to IP addresses Hosts use the Domain Name Server to request the IP address that corresponds to a particular url such as www moxa com Input the IP address of the primary Domain Name Server in the Domain server 1 IP address field and the IP address of the 2 13 CN2610 User s Manual Getting Started secondary Domain Name Server in the Domain server 2 IP address field When the CN2610 receives a connection request the CN2610 first checks the host table defined on the Host_table page If a matching entry cannot be found the CN2610 sends a query to the Doma
242. t s mode is set to ASPP The connection will fail if the port mode is set to something other than ASPP After entering the Console screen select Port gt Mode move the cursor to the Application corresponding to the serial port and set it to Device Control In the Mode column select ASPP gt MOXA provides example programs on the website www moxa com that can be downloaded SLIP PPP Connection Problems Problem Cannot make a SLIP connection to a remote host Solutions gt Check to see if the CN2610 s SLIP port baudrate in the Port gt Line menu is the same as the remote host s baudrate gt Check to see if data bits 8 Check to see if the XON XOFF flow control is the same as the remote site gt Check to see if the RS 232 cable is wired correctly If the port is utilizing RTS CTS hardware flow control then the RTS CTS pins should be included In this case cables with only pins 2 3 and 7 will not work v gt Make sure there is no getty or other process using the SLIP port on the remote site RADIUS Problems Question What can I do if there is an authentication check failure on the radius server Solutions gt Check to see if the console password is the same as the radius server s radius key gt Make sure the password was entered correctly gt Make sure the account and password in the login script are correct gt If the authentication check runs for a long time and then times out che
243. t Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Mode and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports Enter select ESC previous menu 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 T Real COM Async Server Proprietary Protocol 02 T Real COM Async Server Proprietary Protocol 03 T Real COM Async Server Proprietary Protocol 04 T Real COM Async Server Proprietary Protocol 05 T Real COM Async Server Proprietary Protocol 06 NT Real COM i Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol N N N N N 1 oi N N NT Real COM NT Real COM Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter s Pork Application t ption more setting 01 Real COM Server Proprietary Protocol 02 Real COM
244. t to 0 minutes the port will not disconnect Link quality Yes No If you are using software to collect Link Optional report quality information choose YES Outgoing PAP ID Dial out user account ID information Optional ID PAP password Password Dial out user account password Optional To configure the SLIPD mode parameters move the cursor to the Detail setting column to highlight SLIP parameters and then press Enter Enable Detail setting TERM_BIN mode PPPD mode SLIPD mode Term parameters PPP parameters ISLIP parameters J yes yes 10 The pop up selector contains input display fields for Destination IP addr Source IP address IP netmask TCP IP compression and Inactivity time Each item is described in detail below the figure Destination IP address Source IP address IP netmask TCP IP compression Inactivity time Setting Value Notes Necessity Destination IP IP address for the You need to assign an IP address for the Required addr remote Dial in remote user Dial out user Source IP IP address for the The CN2610 will automatically assign Optional address port an IP address for the port We recommend leaving this space blank IP netmask IP netmask The CN2610 automatically assigns the Optional netmask 255 255 255 255 We recommend leaving this space blank TCP IP Yes No Depends on whether the remote user s Optional compression application request
245. tary Protocol 03 NT Real COM ASPP Async Server Proprietary Protocol 04 NT Real COM ASPP Async Server Proprietary Protocol 05 NT Real COM ASPP Async Server Proprietary Protocol 06 Dialin out Bto Term SLIP PPP identification OW NT Real COM ASPP Async Server Proprietary Protocol 08 NT Real COM ASPP Async Server Proprietary Protocol 4 The pop up selector contains input display fields for TERM_BIN mode PPPD mode and SLIPD mode Each item is described in detail below the figure Enable Detail setting TERM_BIN mode iyesi Term parameters PPPD mode yes PPP parameters SLIPD mode SLIP parameters Setting Value Notes Necessity TERM_BIN mode yes no Select yes to enable a Binary Terminal Optional connection PPPD mode yes no Select yes to enable a PPPD connection Optional SLIPD mode yes no Select yes to enable a SLIPD Terminal Optional connection Authentication type None None Authentication is not required Optional local local Check the ID stored in the server User_table defined under the SERVER MENU Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information 5 To configure the TERM_BIN mode parameters move the cursor to the Detail setting column to highlight Description more setting and then press Enter Enable Detail setting Pe CCM Tern parameters PPPD mode yes PPP parameters SLIPD mode SLI
246. ted Optional automatically If set to 0 minutes the port will not disconnect Link quality Yes No If you are using software to collect Link Optional report quality information choose YES Outgoing PAP ID Dial out user account ID information Optional ID PAP password Password Dial out user account password Optional 12 7 CN2610 User s Manual Setting Up Dial in Out Setting Value Notes Necessity Incoming PAP None local server None Authentication is not required Optional check local Check the ID stored in the User_table defined under the SERVER MENU You will need to configure the user s information later in this chapter Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information 5 Press Esc to return to the PORT MENU Configuring Dynamic Mode Dynamic mode integrates PPPD SLIPD and Terminal dial in services Dynamic mode automatically detects which remote connection mode is being used and provides corresponding services You can further enable disable PPP SLIP Terminal services by using the Description more setting pop ups 1 Move the cursor to the Mode column for the port and then press Enter Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting Async Server Proprietary Protocol Async Server Proprietary
247. ter is directly attached to your computer click Local printer IF it is attached to another computer or directly to the network click Network printer Ei k J Automatically detect and install my Plug and Play printer Network printer 5 Select Create a new port and then select LPR Port from the drop down list Click Next to continue Add Printer Wizard Select the Printer Port Computers communicate with printers through parts Select the port you want your printer to use If the port is not listed you can create a new port C Use the following port LPT1 Printer Port LPT2 Printer Port LPT3 Printer Port COM1 Serial Port COM2 Serial Port FAMI Serial Part zi Note Most computers use the LPT 1 port to communicate with a local printer Create a new port Type LPR Port z AppleT alk Printing Devices Local Port LPR Port 6 Enter the CN2610 s IP Address and then enter the Print Queue s name Click OK to continue Add LPR compatible printer A xj Name or address of server providing Ipd fi 92 168 1 1 Name of printer or print queue on that server fasci_4 Cancel Help 13 18 CN2610 User s Manual Setting Up Printer 7 Select the printer s manufacturer and model name Click Next to continue Add Printer Wizard Add Printer Wizard The manufacturer and model determine which printer to use 7 Select the manufacturer and model of your printer
248. the CN2610 and the CN2610 will listen on different TCP ports for connection requests from various Moxattyd Once a connection is established the Terminal server can use hot keys to switch sessions In this way one terminal can control different Unix hosts The following topics are covered in this chapter Accessing the Console Utility Selecting the Application Configuring FIXTTY Mode Configuring the Serial Ports Save Restart O COOUOOCCD Setting up Hosts gt Installing and Compiling Fixed TTY Driver gt Fixed TTY Driver for Different Applications gt Using Fixed TTY Driver CN2610 User s Manual Setting Up Multi Host TTY Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address TS 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 7 Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 sAve Utility Restart Exit Examine modify async server node table configuration
249. the NPort Manager Program on to your NT workstation Click on Next to Continue Cancel 7 After the driver is installed CN2610 Pro Manager and the Add Server Wizard will start running automatically Select Yes and then click Next to continue sA NPort Pro Manager Custom Server Port Help Tak Gee Za CN2610 8 19 Add Server Wizard Ea Welcome to Ar Canar Dea You may add a new server now Make sure Fort Server Pro you have connected the NPort Server Pro to the network and then plug in the power cord before continuing Do you want to run Add Server Wizard now C No l will run Add Server wizard later www moxa com 4 40 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 8 Select one of the server s in the list or select No I will define the server myself if the correct server is not listed Click Next to continue Add Server Wizard CN2 192 168 127 254 5631 9 Ifnecessary enter a different IP address in the Server IP address box and then click Next to continue Add Server Wizard 4 41 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 10 Select the COM number for the CN2610 s port 1 The rest of the ports will be mapped automatically Click Next to continue Add Server Wizard Ea Welcome to Your COM Port NPort Server Pro Name CN2510 8_5631 Serial No 5631 Tota
250. the address of the machine through which packets must be routed Netmask Network pattern of the gateway Metric Number of hops to the destination Flags State of the route Valid states are U up D down G route to a gateway H route to a host T setting in route table R dynamic by RIP Use Correct number of packets being sent in this route Press Esc to return to Routing From the MONITOR MENU select PPP Trace and then press Enter CON ZED Gero V2 MONITOR MENU Line Network Async async Setting Routing PPP Trace Uae Trace PPP protocol connect messages Enter select ESC previous menu 16 6 CN2610 User s Manual Administrative Utilities 2 Use the arrow keys to select the port you wish to trace and then press Enter to select SAE O enoe to VZO O O OOOO Line Network Async async Setting Routing Trace PPP protocol connect messages ESC back to menu Enter select Select port eL 02 03 10 11 ple l Zis CSMS S V2 Network Async async Setting Routing PPP Trace Quit Trace PPP protocol connect messages ESC back to menu Enter select TRACE PORTs O1 P01 state LCP Req Sent PO1l send C0210145001C010405DC0206000000000304C0230506BE2B92D707020802 PPP states for the selected ports are shown LCP Link Control Protocol which is an essential part of the PPP link is used for establishing configuring and testing the data link connection 4 Press Esc to return to PPP Trace D
251. ting Oe Real COM Async Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol Terminal ASCII Termianl mode 8 sessions NT Real COM Async Server Proprietary Protocol Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting jal NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM Proprietary Protocol 05 NT Real COM rver Proprietary Protocol 06 Terminal TERM_BIN rminal mode 8 sessions Real COM rver Proprietary Protocol Real COM Async Server Proprietary Protocol 07 08 NT NT 10 4 CN2610 User s Manual Setting Up Terminal 3 Move the cursor to the Description more setting column and press Enter C2 61 0 5 ra CN261028 19 V20 O Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real COM Async Server Proprietary Protocol 02 NT Real COM Async Server Proprietary Protocol 03 NT Real COM Async Server Proprietary Protocol 04 NT Real COM j Async Server Proprietary Protocol 0S NT Real COM Asyn
252. to menu Enter select Port Enabl no flialize 1 Phone Number yes FEB no Bete Bete no mo no ste Setting Value Notes Enable yes no Enable modem settings Initialize String Set the modem initial string E g AT amp SO 1 for auto answer Dial Up String Dial up AT command Phone Number Number Set the number you use to dial out NOTE The Dial Up and Phone Number settings are only valid under PPP SLIP mode 4 Press Esc to return to the PORT MENU 12 14 CN2610 User s Manual Setting Up Dial in Out Optional Welcome Message Open Port Menu gt Welcome_MSG to set up a welcome message to greet dial in users 1 From the MAIN MENU use the arrow keys to select Port and then press Enter Server seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 2 From the PORT MENU select Welcome_MSG and then press Enter Mode Line mOdem oltame Edit the hello message for Terminal port ESC back to menu Enter select VVVVVVVVVVVVVVVVVVVVVVVVVVvEnable hello message lt lt lt Moxa Async Server gt gt gt 3 Select yes to edit the welcome message 4 Press Esc to return to the PORT MENU Configuring Optional Local User Information Open Server Menu gt User_Table to configure local user authentication information If you set Incoming PAP check or Authentication type as Local instead
253. top this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway 14 Wait patiently while the driver is installed Copying Files x pd z npcfg dll To F WINXP System32 4 13 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 15 You can select the CN2610 that was located automatically or select Manually Enter the IP address of CN2610 Server Async Server and then enter the IP address of a different server Click Next to finish installing the CN2610 driver MOXA NPort Server Installation Select the NPort Server 7 Async Server you want to install Which the NPort Server Asyne Server is that you want to install 16 The next window reports that the driver was installed and port drivers will be installed next Click Next to continue MOXA NPort Server Installation NPort Servers Async Servers installation completed NPort Server Asyne Server is ready to install Port driver CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 17 Click Finish to complete the installation of the server driver This will automatically trigger the port installation procedure Add Hardware Wizard Installing Ports Completing the Add Hardware Wizard The following hardware was installed val MOXA Async Server CN2510 8 Windows has finished installing the software fo
254. ts own MAC address The MAC address is the unique hardware Ethernet address used to identify a network hardware product Write each of the two MAC addresses in the space provided below for future reference LAN 1 MAC address LAN 2 MAC address 2 Getting Started This chapter includes instructions on where and how to install the CN2610 dual LAN async server Both basic and advanced software configuration instructions are given The following topics are covered in this chapter Q Hardware InstallationDesktop gt Rackmount gt Wiring Requirements gt Connecting the CN2610 8 16 s Power gt Connecting to the Network gt Connecting to a Serial Device gt Connecting to the Console Port Q Accessing the Console Utility gt Configuration Checklist gt Accessing the Console from a Telnet Terminal gt Accessing the Console from a Telnet Terminal Q Configuring the CN2610 The Server Menu gt Server Configuration Info gt Server Configuration LAN gt Server Configuration Adv gt Server Configuration Host_table gt Server Configuration Route_table gt Server Configuration User_table L Save Restart CN2610 User s Manual Getting Started Hardware Installation Desktop Place your CN2610 on a clean flat well ventilated desktop For better ventilation attach the 4 pads from the desktop kit to the bottom of the unit and leave some space between the CN2610 and other equipment Do not plac
255. u 3 The Mode page has pop up selection lists for Application Mode and Description more setting for each serial port Use the arrow keys to move the cursor to the Application column for the port to be configured and then press Enter We use Port 6 to illustrate Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 T Real COM Async Server Proprietary Protocol 02 T Real COM Async Server Proprietary Protocol 03 T Real COM Async Server Proprietary Protocol 04 T Real COM Async Server Proprietary Protocol 05 T Real COM Async Server Proprietary Protocol 06 NT Real COM i Async Server Proprietary Protocol Async Server Proprietary Protocol Async Server Proprietary Protocol N N N N N 1 oi N N NT Real COM NT Real COM Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Pork Application t ption more setting 01 Real COM Disable Server Proprietary Protocol 02 Real COM Dialin out Server Proprietary Protocol 03 Real COM Server Proprietary Protocol 04 Real COM Reverse Terminal Server Proprietary Protocol 05 Real COM Device Control Server Proprietary Protocol 06 1X t LO Multiplex Server Proprietary Protocol ag Real COM Printer Server Proprietary Protocol 08 Real COM Niili kose NAE Server P
256. under the SERVER MENU Server Check the ID with the external RADIUS server Refer to Appendix C for RADIUS installation information Optional TCP alive check 0 99 minutes The time period the CN2610 waits before time checking if the TCP connection is alive or not If no response is received the CN2610 will reset the port and terminate the connection Optional 3 Press Esc to return to PORT MENU Configuring the Serial Ports Open Port Menu gt Line to configure serial port settings 1 From the MAIN MENU select Port and then press Enter CN26 LO 6L 8 250 Server Port seTting sAve Utility Restart Exit Examine modify async server ports configuration Enter select ESC previous menu 9 5 CN2610 User s Manual Setting Up Reverse Terminal 2 From the PORT MENU select Line and then press Enter PORT MENUS WOCE Line EEO Gna ERENCE a Examine modify asynchronous port configuration Enter select ESC previous menu 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item is described in detail below the figure CWZ G S v0 Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed STOP Deusy Flr RIS CTS XON XOFF Dascons o1 115200 db None yes yes no None 02 PES
257. us menu 2 From the PORT MENU select Line and then press Enter CN AG LOSS LS VZO WOCE Line EE ena EEN OE a Examine modify asynchronous port configuration Enter select ESC previous menu 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item is described in detail below the figure CHASO S S ras Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed Ls Parity Firo RIS CTS XON XOFF DESEO br al None i yes None 02 TIS200 None i yes None 03 DIS200 None s yes None 04 LLSZQO None f yes None 05 aio 200 None i yes None 06 115200 None i yes None 07 aio 200 None yes None 08 LIS2QO None i yes None PRPPRPRPRPRPE 13 7 CN2610 User s Manual Setting Up Printer Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 1 1 5 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off wi
258. uto Term SLIP PPP identification OP Dialin out DYNAMIC Auto Term SLIP PPP identification 03 Dialin out DYNAMIC Auto Term SLIP PPP identification 04 Dialin out DYNAMIC Auto Term SLIP PPP identification CN2610 User s Manual RADIUS Server Enable Detail setting TERM_BIN mode Term parameters PPPD mode 3 PPP parameters SLIPD mode 3 SLIP parameters TERM_BIN mode Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 Dialin out Point to Point Protocol 02 Dialin out Point to Point Protocol 03 Dialin out Point to Point Protocol 04 Dialin out Point to Point Protocol Destination IP address Source IP address IP netmask TCP IP compression g Inactivity time 3 minutes Link quality report Outgoing PAP ID PAP password Incoming PAP check Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 Terminal TERM_ASC ASCII Terminal mode 8 sessions 2 Terminal TERM_ASC ASCII Terminal mode 8 sessions 03 Terminal TERM_ASC ASCII Terminal mode 8 sessions CN2610 User s Manual RADIUS Server Key Mapping Max Sessions Change Session Quit Break Interrupt Auto link protocol Telnet TCP port Primary nost IP Link by input IP Secondary host IP Auto login
259. ver ESC back to menu Enter select Wa ove DN Restart system will disconnect all ports and clear all status value Enter continue ESC cancel 14 13 15 Setting Up Routing Routing is the main process used by Internet hosts to deliver packets The Internet uses a hop by hop routing model which means that each host or router that handles a packet examines the Destination Address in the IP header computes the next hop that will bring the packet one step closer to its destination and then delivers the packet to the next hop where the process is repeated Two things are needed to make this work 1 Routing tables must match destination addresses with next hops and 2 routing protocols must determine the contents of these tables The CN2610 provides easy to use routing functions that support both static routing tables and dynamic RIP1 RIP2 routing protocols This chapter illustrates how to configure static routing tables and dynamic RIP1 RIP2 protocols A few routing examples are also given to illustrate some basic routing concepts The following topics are covered in this chapter Accessing the Console Utility What is RIP Configuring RIP Configuring the Static Routing Table Static Routing Examples gt Configuring Routes to the Internet OOoOCOD gt Configuring Routes to the Internet and Intranet gt Configuring Multiple Point Routes Save Restart Oo CN2610 User s Manual Setting Up Routing
260. which Required serial device to send data to These values are fixed and cannot be changed by the user Serial Port TCP Port No 01 950 02 951 03 952 16 965 TCP command 966 981 The host uses this Port value to determine which Required port device to send commands to These values are fixed and cannot be changed by the user Serial Port TCP Port No 01 966 02 967 03 968 16 981 8 5 CN2610 User s Manual Redundant COM NOTE Max Connection 1 4 default 1 This field is used if you need to receive data from different hosts simultaneously When set to 1 only one specific host can access this port of the CN2610 and the COM driver on that host will have full control over the port When set to 2 or greater up to the specified number of hosts COM drivers may open this port at the same time When multiple hosts COM drivers open the port at the same time the COM driver only provides a pure data tunnel no control ability The serial port parameters will use firmware settings instead of depending on your application program AP Application software that is based on the COM driver will receive a driver response of success when the software uses any of the Win32 API functions The firmware will only send data back to the driver on the host Data will be sent first in first out when data comes into the CN2610 from the Et
261. wn above in the structure diagram All aspects of the system are backed up including the PC hosts the networks and the CN2610s The entire system will continue operating in the following situations 1 When the Primary PC and LAN A fail at the same time the backup PC and LAN B will take over 2 When the Primary PC and the Primary CN2610 fail at the same time the backup PC and the backup CN2610 will take over 3 When LAN A and the Primary CN2610 fail at the same time LAN B and the backup CN2610 will take over The RS 232 connector on the Remote Terminal Unit RTU shown above must be setup with an RS 232 to RS 422 485 converter such as the MOXA TCC 100I to convert RS 232 signals to RS 485 signals The connectors on the two CN2610s will also need to use converters such as the MOXA TCC 1001 In this way users can take advantage of RS 485 s multi drop feature to share data with the secondary CN2610 Refer to Chapter 7 for detailed information and configuration instructions 3 6 CN2610 User s Manual Knowing Your Application Redundant COM LAN A Ethernet LAN B Data A CN2610 Serial A RTU The Redundant COM operation mode can be used to set up a redundant LAN between the serial devices connected to the CN2610 s serial ports and the host computer The redundant structure involves using the CN2610 s two LAN ports to set up two independent LANs that connect the CN2610 to the host computer If either
262. x Fixed TTY 3 The Line page has pop up selection lists for Port Speed Bits Stop Parity FIFO RTS CTS XON XOFF and Discon ctrl for each serial port Each item is described in detail below the figure CN2610 8 Mode mOdem Welcome_MSG Quit Examine modify asynchronous port configuration ESC back to menu Enter select Port Speed Parity FIFO RIS CTS XON XOFF DISCON bel top Oh 15200 1 None yes None 02 C1152090 i None f yes None 03 Paka AO iL None s yes None 04 PLS 2 0103 alae None i yes None ala 115200 Laii None amp yes None 06 ELS ZOO aari None i yes None 07 CLS 2001 i 4 None yes None 08 115200 itl None f yes None Setting Value Notes Speed 50 bps to 921 6 Kbps Transmission rate Bits 5 6 7 8 Data bits Stop 1 1 5 2 Stop bits Parity None Even Odd Mark Space Odd Even Mark Space FIFO Yes No First In First Out Device RTS CTS Yes No Hardware Flow Control XON XOFF Yes No Software Flow Control Discon Ctrl None DSR off or DCD off will not be interpreted as a disconnection DSR off DSR off will be interpreted as a disconnection DCD off DCD off will be interpreted as a disconnection 4 Press ESC to return to the PORT MENU Save When exiting the SERVER MENU you will be prompted to save settings Press Y to save GNAGIO s 1S wAsEO ip obo peunit t ely e A Os oE olla mma lolk mm USer
263. xclusively by MOXA to communicate with the CN2610 For both Linux Unix Socket programming and Windows WinSock programming IP is used to communicate between hosts and devices At the end of the chapter we give examples that explain how ASPP is used in a UNIX Windows environment The following topics are covered in this chapter Accessing the Console Utility Selecting the Application Configuring ASPP Mode Configuring RAW Mode Configuring the Serial Ports Save Restart ASPP Library Introduction ASPP Examples for Unix ASPP Examples for Windows OUOCUOODCUUD CN2610 User s Manual Setting Up Device Control Accessing the Console Utility NOTE In this section we show how to access the CN2610 s console utility by Telnet over the network For information on using the console port see the section Accessing the Console Utility in Chapter 2 1 Telnet over the network to the server s IP address Run o o 2x Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 192 168 127 254 x Cancel Browse 2 Type 1 to choose ansi vt100 and then press Enter a Telnet 192 168 127 254 Async Server CN2610 8 Console terminal type 1 ansi vt100 2 vt52 3 The CN2610 s MAIN MENU will open as shown below a Telnet 192 168 127 254 ENZO ey W250 Server SEAIA Ee Mamt 7 0 4 E Ws oh A 5 1 9 or a OI Go Examine modify async se
264. xt window to open states that the software hasn t passed Windows Logo testing you can rest assured that this driver has already been tested and been shown that it can support this Windows OS Click Continue Anyway to proceed Hardware Installation A The software you are installing for this hardware Moxa Port 0 has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway i 4 16 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 4 The driver for MOXA Port 0 will be installed Found New Hardware Wizard Please wait while the wizard installs the software SS E Moxa Port 0 caa LY serenum sys To F WINXPSSystem32 DRIVERS ER RRRRRRR RRR lt Back Next gt Cancel 5 After MOXA Port 0 is installed steps 1 to 4 will be repeated 7 or 15 times depending on whether you are installing drivers for the 8 port or 16 port CN2610 Found New Hardware Wizard Completing the Found New Hardware Wizard S The wizard has finished installing the software for F Moxa Port 0 Click Finish to close the
265. y Protocol Async Server Proprietary Protocol 04 NT Real COM I ASPP Async Server Proprietary Protocol 8 3 CN2610 User s Manual Redundant COM 4 Use the Up Down arrow keys to select Redundant COM and then press Enter C2 6 1 0 2 oaeoeae UBAO O O O OOOO i OoOo Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enters Port Application Description more setting 01 Redundant dant COM mode 02 Redundant dant COM mode 03 Redundant Dialin out dant COM mode 04 Redundant Terminal dant COM mode Q5 Redundant Reverse Terminal dant COM mode 06 Redundant Device Control dant COM mode 7 Redundant Multiplex dant COM mode 08 Redundant Printer dant COM mode Nicie stoic ICI NT Real COM DRDAS Raw UDP Redundant COMI 5 The only operation mode associated with this application is Redundant which is selected automatically in the Mode column Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Mode Description more setting 01 Redundant COM Redundant Redundant COM mode 02 Redundant COM Redundant Redundant COM mode 03 Redundant COM Redundant Redundant COM mode 04 Redundant COM Redundant Redundant COM mode 05 Redundant COM Redundant Redundant COM mode 06 Redundant Redundant COM mode 07 Redundant COM Redundant Redundant COM mo
266. ync Server Proprietary Protocol 02 Real COM Async Server Proprietary Protocol 03 Real COM Async Server Proprietary Protocol 04 Real COM Async Server Proprietary Protocol Real COM Async Server Proprietary Protocol INT Real COM Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enters Port Application t ption more setting 01 Real COM Server Proprietary Protocol 02 Xt LO Dialin out Server Proprietary Protocol 03 Real COM Terminal Server Proprietary Protocol 04 Real COM Reverse Terminal Server Proprietary Protocol 05 Real COM Device Control Server Proprietary Protocol 06 Real COM Multiplex Server Proprietary Protocol 07 Real COM Printer Server Proprietary Protocol 08 Real COM Male tosis Server Proprietary Protocol NT Real COM 4 3 CN2610 User s Manual Windows Real COM Linux Real TTY Unix Fixed TTY 5 ASPP mode is selected by default since it is the only mode associated with the NT Real COM application CZE TO P 19 V20 Mode Line mOdem Welcome_MSG Quit Examine modify the operation mode of async ports ESC back to menu Enter select Port Application Description more setting 01 NT Real Async Server Proprietary Protocol NT Real Async Server Proprietary Protocol NT Real COM Async Server Proprietary Protocol NT Real COM Asy

CN2610 Dual-LAN Async Server User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents