Home

PYXIS G2 User Manual

1. neh eo e om al A ere i Er woe To select a single track double click its number All other tracks will be deselected Another way of selecting a track is to ctrl click on a clip This cannot be used to deselect a track Ctrl clicking will also select the clip and create a range or extend the current one to include that clip Note the mouse can also be used to e Mute or unmute a track click the M e Solo or unsolo a track click the S e Arm or disarm a track click the button at left the track must have an input patched to it before it can be armed Time Scale and Display Zooming The track display represents a 24 hour continuous loop The timescale can be zoomed from one sample across the screen to eight hours The Zoom number and screen width are shown at the upper left of the screen gt ts To change zoom range Turn the Mouse wheel Or Click on the Zoom icon and drag the mouse up or down Track display selection and zooming is possible while playing and recording Pyxis G2 Page 29 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 Timescale display Timecode positions can be displayed in whole frames frames with subframes frames with subframes and samples feet and frames in either film format or Bars and Beats For all timescale choices select View gt Timescale and choose one of the options View nf Display Layering
2. Talkback Description Mic level input and line level output for studio talkback microphone Mic input may be configured to carry 8VDC phantom power for electret and condenser microphones Connector D 9 Female E Connector ma pe m e me e E Pyxis G2 Page 163 Operator Reference Manual CHAPTER 25 SPECIFICATIONS September 15 2011 USB Description Standard USB port Cable must be shielded and less than 3 meters in length Connector USB Type A Female USB Type A Signal Connector USBDO GND GPIO Description General Purpose I O Connector D 15 Female Input low lt 0 8 volts high gt 3 5volts lt 5 volts Input voltages higher than 5 volts may cause damage to internal circuitry Output low lt 0 8 volts high gt 3 5 volts por er Connector Connector pus feo ooo Ethernet Description 100BaseT ethernet interface to Pyxis G2 or network Use CAT5 shielded twisted pair cable and shielded RJ45 connectors Connector RJ45 Pyxis G2 Page 164 Operator Reference Manual CHAPTER 25 SPECIFICATIONS September 15 2011 Cross over Cable Required for direct connection between Pyxis G2 and engine Not required if hub is present Pyxis G2 Page 165 Operator Reference Manual INDEX September 15 2011 Index PCPA tareas 54 TACKS ia 104 Assigning signals to Buses 126 AUTO 5 AA ees 74 Automation Lock WindoW o omcoccococ o 162 eg igle AAPP E E 58 Automation Locked to Vid
3. 4 31 Floppy fas a Local Disk Cs e Audio Di 5 etax2003 5 etax2004 5 etax2005 O etax2006 5 Fairlight E Fairlight AU Media ML3_AYT40a50 9 MLS_AYTMewPlugin Projects a The picture above shows the typical file layout with an MT file The FUF file contains the audio while the MT file contains the Edit list mix information and automation files Note The FUF file will generally get much larger up to 4 GB while the MT file already contains a full complement of mix data even if mostly zero values and will only get bigger when automation files are saved When the first FUF file reaches 4 GB another one is automatically created Stuffing FUFs Dream II allows external files to be dragged and dropped onto the timeline Since these files are not recorded into the Dream II MT Project they are not automatically added to the FUF files associated with the MT Project If you want to transfer the MT project and all external audio files to QDC or to another Dream II system select Stuff Fufs All Clips or Stuff Fufs Selected Clips from the Dream II Process menu This will copy all external media into the Project s Fuf files Please note that this process can take some time depending on the quantity and size of external files that need to be stuffed Stuffing Fufs is a background task so you can keep working while Dream II is processing However you cannot save your project until Fuf
4. Do 6 C Ai S3EP33 O016 55 23 00 16 55 mR 7 Ai S3EP33 00 16 55 24 00 16 55 E 7 D A12 34000 18 28 13 17 18 28 16 E C A 34 CLOSE 00 48 26 11 00 48 26 1 a 4 mn mn 9 The system will ue only the highlighted events in ihe EDL display Use the mouse to highlight the required events You can select a range of events by selecting the first then holding down SHIFT and selecting the last in the range You can add or subtract an event from the selection by holding down ctrl and clicking it Events that are marked with an R will not be recorded even if they are selected Pyxis G2 Page 93 Operator Reference Manual CHAPTER 11 EDL MANAGEMENT September 15 2011 Step 3 Step 4 Step 5 Step 6 D 6 C Fi Each time the system performs a recording the events that successfully record are automatically marked this way You may also click in the checkbox for any event to mark or unmark it manually Capture Settings Handles you can capture more audio than indicated by the EDL event This can be very useful for adding fades or capturing ambience around the event for use in smoothing Preroll sets the time that the source machine will run up to the recording Set this value to suit the type of source machine being used Typically tape based machines require at least 3 seconds to lock properly Postroll sets the time that the source machine will keep running after the recording Set up Patching Connect
5. Step 4 Click buttons at the top of the MSAT screen so that Msg Gen is on Msg Sys is off and All Para is off as shown below Pyxis G2 Page 153 Operator Reference Manual CHAPTER 23 HUI SLAVE MODE September 15 2011 Step 5 Step 6 fe MSAT_O 5 x File View Help gt sz Msg Mag All ter Te Msg Meg All Filter Te gt p Gen yz Para PAra ster C Gen Sys Para Para ster 7 Far pot tll Gib bib gt El Set Get Test en El note ES Set Gat Test 14 52 20 Error from ShortHsg 14752724 Error from ShortMsg 14 52 23 Error from ShortHsg cc 14 52 33 Error from ShortMsq 14 52 37 Error from ShortHsgq 14752742 Error from ShortMsg Type ctr1 sHIFT 0 then turn on Control message display using the Debug Switch Control dialog as shown below set the switch value to 1 Then close the dialog Debug Switch Control x Debug Switch Control Meg display T a Switch alue fil Press a HUI key and observe the MSAT display It will show you the name of the key 0 x o Msg All Filter Te Misa Meg All Filter Te O a En po us Para Pars ker Gen Sys Para Para ster 7 nl note iL l 1 1 j gt fe i Gib Set Set Get Test e n B we it ot DB 14 59 29 gt Ctrl CID SW MACKIE Fl gt 0 DB 14 59 30 gt Error from SbortMsa 5 DB 14 59 32 gt Ctrl SN MACKIE Fl 1 DB 14 59 32 gt Ctrl CID SW MACKIE Fl 0
6. DB 14 59 33 gt Ctrl CID SW MACKIE EZ 1 DB 14 59 33 gt Ctrl CID SN MACKIE Fe O DB 14 59 34 gt Error from ShortMsg 5 Stopped a Ready ackets Tx 197 4 In the example shown the keys CID_SW_MACKIE_F1 and CID_SW_MACKIE_F2 have been pressed and released hence two events per key Pyxis G2 Page 154 Operator Reference Manual CHAPTER 23 HUI SLAVE MODE September 15 2011 Advanced using Scripted Macros In Xynergi a number of the HUI keys have been used to trigger scripted macros as follows CID_SW_MACKIE_BANK_DOWN decrement_fader_set CID_SW_MACKIE_BANK_UP increment_fader_set CID_SW_MACKIE_CHANNEL_DOWN decrement4_fader_set jump by four fader sets CID_SW_MACKIE_CHANNEL_UP increment4_fader_set jump by four fader sets CID_SW_MACKIE_UP EQUAL less_tracks show fewer tracks on the edit screen CID_SW_MACKIE_DOWN EQUAL more_tracks show more tracks on the edit screen If you wish to release one of the HUI keys for other functions you must edit the Events txt file in C Program Files Fairlight FMC Data User Xynergi_ For example to liberate CID_SW_MACKIE_BANK_DOWN add a hash in front of the line CONTROL CID_SW_MACKIE_BANK_DOWN EQUAL 1 decrement_fader_set like this CONTROL CID_SW_MACKIE_BANK_DOWN EQUAL 1 decrement_fader_set Then you can use CID_SW_MACKIE_BANK_DOWN in your remap file or trigger a different scripted macro Pyxis G2 Page 155 Operator Reference Manual CHAPTER 24 SYSTEM FILES September
7. FAIRLIGHT Pyxis G2 Operator Reference Manual 15 September 2011 Software Version 3 2 Issue 001 Important Notice COPYRIGHT The material in this document is copyright to Fairlight AU Pty Ltd and may not be quoted or reproduced in any form without written permission from the company Fairlight is a trademark of Fairlight AU Pty Ltd All other trademarks are the property of their respective owners LIMITED WARRANTY POLICY All the software and hardware provided with or purchased especially for Fairlight products has been tested for functionality Fairlight AU Pty Ltd will make its best efforts to correct re ported defects for future releases subject to technical practicalities Fairlight AU will also replace any defective media on which software has been delivered provided that the item to be replaced is returned to the dealer who supported the product within 90 days of purchase Fairlight AU Pty Ltd makes no warranty or representation either expressed or implied with re spect to the system s performance or fitness for a particular purpose In no event will Fairlight AU Pty Ltd be liable for direct or indirect damages arising from any defect in the product or its documentation Further Fairlight AU Pty Ltd will not accept any liability for any programs sounds audio recording or sequences stored in or used with Fair light products including the cost of recovery of such data Product features and specifications are subject to
8. The clip is pasted Head This time we ll only work with the Head of the clip That is the part before the cursor Step 1 Select a track and move the transport so that a clip is under the cursor The clip is red because it is touching the cursor Step 2 Click the cut button on the Tool Bar if not already selected Step 3 Click the Head button Only the head goes on to the clipboard Step 4 Select another track and or move to another location Pyxis G2 Page 64 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 The ghost shows a head Shaped clipboard ready to be pasted The original tail is now Blue because its track is not selected Step 5 Click the Paste button to paste the clipboard The clipboard former head is pasted Range You can make a range that specifies exactly which part of the clip is affected The easiest way is like this more about ranges later Step 1 Move the transport where you d like to start the range Step 2 Click the From button Step 3 Move the transport where you d like to end the range Step 4 Click the To button The range is marked in red Now we l cut and paste the audio in the range Step 1 Choose the track and set the range we ve just done this Step 2 Click the cut button on the Tool Bar if not already selected Step 3 Click the Range button Pyxis G2 Page 65 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 T
9. oooo 00000000 e o Lte Generator Enabled TT In Stop 00 00 00 00 Video Arm Enabled Type Config Mame Enabled Serva Timecode Ofset Status Te Master confia IA P ee TEN 00 00 00 00 00 Stopped Jure Chase c Chase a ee anomna 0000 00 00 Stop Chase config a ee ent 00 00 00 00 ERTIME OUT Lc Generator Enabled In Stop 00 00 00 00 Video Amn Enabled fim En ideo Analog Digital Asm Inh ef V e occo VOLS o oo T e e coo o o For each machine that you want to use select one of the following machine types e TC Master the selected machine is the 9 Pin timecode master e Chase slave the selected machine is in 9 Pin chase mode e Remote slave Dream II will respond to 9 Pin remote commands like a virtual VTR e LTC Master the selected machine is set to chase external Longitudinal Time Code e MTC Master the selected machine is set to chase external MIDI Time Code e Pyxis selecting Pyxis Track as one of your machines allows you to take the Video Track offline the same way as physical machines See Editing with Machine Control on page 148 to see how this works e No Port No port selected Pyxis G2 Page 142 Operator Reference Manual CHAPTER 22 MACHINE CONTROL September 15 2011 Note You can have only one Master machine at a time but you can have as many slave machines as you like limited only by available ports Master and Slave machines can be
10. D Fairlight4U Projects New Project11 id 0 Folders File Folder etax2003 33 337 KB DRZ File 5 etax2004 5 etax2005 5 etax2006 Fairlight E 5 Fairlight4u The picture above shows the typical file layout with a DR2 file The Media folder which is automatically created by the system contains the audio in the form of WAV files while the DR2 file contains the Edit list mix information and automation files Pyxis G2 Page 130 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 View Favorites Tools Help ae r i T i eo gt Bi P Search lear Folders J Oi Fairlight amp U Projects New Project9 Media 0 Mame Size Type SUFL_Recorded Audio 13_al 1GCB4Z6BC437x wav 766KB WAV Audio Ej FL Recorded Audio 14 a2 16C0426BC43 YY way 766 KB WAY Audio Ej FL Recorded Audio 15 _a3 1GC0426BC43VZ way 766 KB WAv Audio E FL Recorded Audio 16_a4d 1GC0426BC43V_ way 766 KB WAY Audio Ej FL Recorded Audio 17_a5 16C8476BC4320 way 706 KB WAY Audio Ej FL Recorded Audio 19 _46 16C8476BC457 1 aw 766 KB WA Audio EA isk Free space 101 GB 4 48 ME 4 My Computer Z The Media folder looks like this The WAV files are named as follows Clip Name _ Track number _ GUID wav The Clip name is the automatic name given to the clip by the system see Seed Names on page 101 Or you may have named the clip while recording it see Naming Clips on page 101 The Track number is the one o
11. Export 3 Video This box pops up Pyxis G2 Page 121 Operator Reference Manual CHAPTER 18 IMPORT EXPORT September 15 2011 2 E alia noe availa Step 2 Choose the video format you wish to export as Step 3 Choose whether you want to export the whole project or a selected range NOTE to export as a Quicktime file you must have the latest version of Quicktime installed Pyxis G2 Page 122 Operator Reference Manual CHAPTER 19 MONITORING September 15 2011 Chapter 19 Monitoring Introduction Pyxis G2 provides three monitoring buses in the most popular formats 5 1 Stereo and Mono It allows any number of tracks to be assigned to the monitor buses Assigning Tracks to Monitor Buses Step 1 Click the Monitor Assign button in the Setup megamode Step 2 The Buss Assign Panel is displayed Click to select the destination bus to which you want to assign signal paths This can be the 5 1 Stereo or Mono bus The selected bus key will be highlighted The keys of Tracks already assigned to that bus will light up ia nal ooo en ae en en 200 a ee kaa kaa ee ee a Pyxis G2 Page 123 Operator Reference Manual CHAPTER 19 MONITORING September 15 2011 Step 3 Step 4 In this case we have selected the 5 1 Monitor bus The tracks assigned to it are highlighted Click any Track tile to toggle its assignment on or off Press the All Tracks soft key to assign all tracks to the selected b
12. Oooo Mix Tracks to Mono or Stereo automaticall etna 2ingle Multichannel File all selected tracks 1 Tracks Mono files 1 per track Creates a single mono media file for each track in the export i e all tracks or selected tracks depending whether the Selected Tracks Only checkbox is selected Pyxis G2 Page 120 Operator Reference Manual CHAPTER 18 IMPORT EXPORT September 15 2011 Stereo files 1 per track pair For each pair of tracks in the export a single stereo media file is created Mono Stereo files automatically choose If a track is mono and contains no multi channel clips its contents will be exported as a stereo media file If a pair of tracks are linked as a Link Group their contents will be exported as a stereo media file If a track contains a two channel clip its contents will be exported as a stereo media file Mix Track to a single Mono File All tracks in the export are mixed together to form a mono mix and this is recorded into a mono media file Mix Track to a single Stereo File All tracks in the export are mixed together to form a stereo mix and this is recorded into a stereo media file Single MultiChannel File all selected tracks A single file is created with multiple linked media one for each track in the export Exporting Video You can export the video straight from a project and automatically combine it with your choice of audio from a project Step 1 Use the command File
13. click the Close Box or right click anywhere in the dialog or press the Esc key on your QWERTY Pyxis G2 Page 100 Operator Reference Manual CHAPTER 13 NAME September 15 2011 Chapter 13 Name Introduction Pyxis G2 allows you to rename tracks and clips and to setup seed names for recording When a name function is selected the original name appears in a popup window You can then use the BAcKSPACE key to delete the original name and supply a new one Naming Tracks Step 1 Select the Track s you want to rename Step 2 Use the command Tracks Rename Track Step 3 Type the name in the popup window that appears on the PC screen Step 4 Press Enter on the QWERTY keyboard or click OK There is a maximum of 16 characters allowed for naming tracks Note that all the selected tracks will be given the same name at the same time Naming Clips To rename a clip use the command Edit Rename then type the new name for the clip and press Enter on the QWERTY keyboard or click OK Seed Names Names are given to all new recordings in a Project You will notice that recordings are given an incrementing number for each new clip Seed names allow you to enter a name prefix that will be given to each new recording to which an incrementing number will be appended Each track has its own Seed Name but you may apply the same one to many tracks To set the seed name for one or more tracks Step 1 Select the Track s you want to re
14. if not already selected If already selected removes it from the selection makes it blue With no range click on a clip and drag it The clip moves to any track and time where you drag it The destination track is selected With a range click on a selected clip All selected clips move across tracks and time as and drag it you drag them Display Layering When clips are placed on top of each other only the uppermost is heard or at most a crossfade between the top and second layers The software allows you to see all the layers using the command View 3 Display Layering Pyxis G2 Page 81 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Cy Display Layering Pyxis Locators Tracks e Video Track Clip Search Statistics Performance Background Tasks The layers of clips are shown on all tracks with the clips becoming thinner as needed to fit the available space Pyxis G2 Page 82 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Eg z 1 Master 23 o4 40 08 pis Top Layers The mouse can be used to change the order of clips To do this simply click and drag a clip from one level to a higher or lower level Changing levels in this way can be combined with dragging a clip to a different track or timecode Note that there is always a space at the top of each track equal to the width of one clip This is to allow room for you to drag a clip into the top position
15. o o PJ geaj meej meo ma mas ra Soc Se El E E Destination categories Source Categories Categories of signal paths are selected in the lower part of the screen Pyxis G2 Page 56 Operator Reference Manual CHAPTER 7 PATCHING AND ASSIGNMENT September 15 2011 Selecting a category of sources expands the category in the upper left of the screen In this case Analog Inputs have been selected Source categories Track 1 1 Track 2 Track 3 1 Track 4 Destination Categories Selecting a category of destinations expands it into the upper right of the screen Destination categories Pyxis G2 Page 57 Operator Reference Manual CHAPTER 7 PATCHING AND ASSIGNMENT September 15 2011 In this case Track Inputs are shown Sx20 411 Sx20 AIZ SAZO ALS INE Making a Patch Select a source and a destination then click the Patch button in the center Patch Afterwards the tiles used in the patch will show the results Source is always shown above destination Source Track 1 1 Destination Destination Source Notes You can select multiple sources and multiple destinations and patch them all with one command For example select Analog Inputs 1 to 8 and Track Inputs 9 16 then click the Patch command once To deselect all the signal paths you have selected touch the Clear button The Multi Button Clicking the Multi button allows you to patch the same sources
16. where all segments of the meter are illuminated orange To clear this display press the Meter Sets key The over hold time can be set by editing the following line in the file enter the hold time in ten millisecond increments Overload display time 1000 Overload Peak Hold The main meters can display digital overloads by holding the entire bar The amount of time this display remain after the overload has passed can be set Edit the following line to enter the hold time in milliseconds Overload display time 1000 Pyxis G2 Page 160 Operator Reference Manual CHAPTER 24 SYSTEM FILES September 15 2011 GPIO Enable The GPIO port on the rear of the Pyxis G2 must be enabled for use by a GPIO macro Replace the O with 1 in the following line to enable GPIOs GPIO ENABLED 0 Plug Ins I O The physical digital I O used by the optional plug ins system must be specified The I O must be a block of 16 or 32 starting at 1 17 or 33 Edit the following lines to specify the first channel and the range of the I O block PLUGINS IO START 17 PLUGINS IO RANGE 16 Plug in Name Display The name of the plug in may be displayed in the channel display Edit the following line to turn this feature on or off SHOW PLUGIN NAME 1 Remote Mic amps To configure the Pyxis G2 to control a UP4 mic pre add the following statement to the FMC INI file UP4 ip address x y where e ip _address is the address of the UP4 unit e xis the nu
17. 00 gt product 65535 GDB 09 43 00 gt version 1 1 GDB 09 43 00 gt name USB Audio Device 4 GDB 09 43 00 gt Midi Out 4 of 5 name Microsoft GS Wavetable SW Synth GDB 09 43 00 gt MIDI Out device 4 GDB 09 43 00 gt manufacturer 1 GDB 09 43 00 gt product 102 GDB 09 43 00 gt version 5 10 GDB 09 43 00 gt name Microsoft GS Wavetable SW Synth GDB 09 43 00 gt Using MIMidi Out 0 A number of MIDI devices may be presented not necessarily with useful names this depends on the driver for the device At the end the line GDB 09 43 00 gt Using MIMidi Out 0 tells you which MIDI device the system is using If this is clearly not your HUI device nothing is going to work In the example given it is possible to see that Microsoft GS Wavetable SW Synth has not been selected Pyxis G2 Page 151 Operator Reference Manual CHAPTER 23 HUI SLAVE MODE September 15 2011 Remap File If you want transport control or any other key events to work you must place a file called remap txt in the following folder C Program Files Fairlight FMC Data User username Where username is the log on name used on your computer The remap file takes keys coming in from the HUI device and routes them to keys on your Dream II system Here is the text in one remap file CID_SW_MACKIE_STOP CID_SW_STOP CID_SW_MACKIE_REWIND CID_SW_REW CID_SW_MACKIE_FAST_FWD CID_SW_FF CID_SW_MACKIE_PLAY CID_SW_PLAY CID_SW_MACKIE
18. 2 Type a new name into the Presets field or use an old name if you want to change its settings Set the EQ values to the ones you want to save by editing or simply by picking up the values by touching an existing clip Click the save button To retrieve an EQ setting select it from the Preset drop list It can then be applied immediately to the currently selected clip or range of clips A saved EQ setting can be deleted by first selecting it from the drop list then clicking the Delete button A special preset can be created called default Whenever the Clip EQ display is opened for a clip with no EQ this preset will automatically be loaded into the display Pyxis G2 Page 91 Process EDL Operator Reference Manual CHAPTER 11 EDL MANAGEMENT Chapter 11 EDL Management Introduction EDL Management supports three activities associated with EDLs Edit Decision Lists produced by other editing products Capture Conform locations indicated by the edit list Reconform re edits an existing DREAM II project according to a cut list usually representing a re edit of the pictures in a video project Loading an EDL The first step is to load an EDL file Step 1 Step 2 Use the command File Import EDL This will cause the display of the EDL dialog 1 C A12 ANIMALI 7 C Ai 3 E A 34 3 D A 34 12 4 C A12 BL 4 D A12 2 53EP33 5 c A 34 CLOSE 6 E A12 53EP33 7 C 2 5 3EP 33 7 D 34
19. Capture process as the audio is already present on hard disk but otherwise the process is very similar to Conform Each reel in the EDL may be mapped to a different audio project Step 1 Set up Track Mapping as for Capture Commonly all tracks will be involved The Record Tracks correspond with the source tracks from the existing Source Project Step 2 Select Edits to Reconform as for Capture Step 3 Link Reels Each reel can come from a different project if required Use the Reel Linking dialog to choose the project for each reel select a reel then click the Project button and browse to the correct Project to be linked Reel Linking Reel Project CTN G lPairlightALlProjectsiDA_AMBIGIDA AMBIG DR2 03000 G Fairlight amp U Projects MT_ForeigniMT_ Foreign MT LIB 2 34000 GUPairtightaDlProjectsiS6 Tracks Tracks DRZ LIB 3 32000 G Fairlight amp U Projects ImportRobotsTestiImportRhobotsTest DR LIB 4 10000 a Fairlightau Projects New Project O New Project o DRZ LIE 5 35000 GU FairlightaU Projects New Projecti44 New Project144 DR 2 LIB 6 16001 G Fairlight AUi Projects New Projecti44 New Project144 DR 2 LIB 6 PREREAD Gi FairlightaU Projects New Projecti21Mew Projectlz DRZ LIB 1 MAINRECO GU PairlightaDlProjectsiMew Projecti2 Hew Project12 DR 2 LIB 1 31000 G Fairlight amp Ui Projects New Project12 MNew Project12 DR2 LIB 1 36000 G PairliqhtAaLMProjects Mew Projectl2iWew Projectiz DRZ LIB 1 03003
20. ES m a e m n e i o e e 00 01 04 1 3 00 00 31 15 This area contains three timecode values associated with Editing Ranges They are respectively the Range In time Range Out time and Range duration The From button is used to place the beginning of the Range at the current position The To button is used to place the end of the Range at the current position The Range button toggles the Range on and off When Range is switched off these numbers show the last range that was created which can be restored by pressing the Range On key or selecting the Range On command from the Edit Menu The button at the bottom work as follows Pyxis G2 Page 12 Operator Reference Manual CHAPTER 2 PYXIS G2 OVERVIEW September 15 2011 Jump Left causes the transport to jump to the next jump target to the left Loop causes the transport to loop between the From and To points Jump Right jumps to the next jump target to the right Jump targets are chosen by the command Edit gt Jump To You may check e Marks e Point heads or tails of clips on selected tracks and or e Fade places in clips where a fade out begins on selected tracks Track and Clip Area This area shows a selection of the available audio and video tracks and the clips on them In the above picture the Video Track and Track 2 are both selected active while Track 1 is unselected A complete description of all track functions is con
21. GDB 09 43 00 gt MIDI in device 2 GDB 09 43 00 gt manufacturer 65535 GDB 09 43 00 gt product 65535 GDB 09 43 00 gt version 1 1 Pyxis G2 Page 150 Operator Reference Manual CHAPTER 23 HUI SLAVE MODE September 15 2011 GDB 09 43 00 gt name USB Audio Device 3 GDB 09 43 00 gt Midi IN 3 of 4 name USB Audio Device 4 GDB 09 43 00 gt MIDI in device 3 GDB 09 43 00 gt manufacturer 65535 GDB 09 43 00 gt product 65535 GDB 09 43 00 gt version 1 1 GDB 09 43 00 gt name USB Audio Device 4 GDB 09 43 00 gt Midi Out 0 of 5 name USB Audio Device GDB 09 43 00 gt MIDI Out device 0 GDB 09 43 00 gt manufacturer 65535 GDB 09 43 00 gt product 65535 GDB 09 43 00 gt version 1 1 GDB 09 43 00 gt name USB Audio Device GDB 09 43 00 gt Midi Out 1 of 5 name USB Audio Device 2 GDB 09 43 00 gt MIDI Out device 1 GDB 09 43 00 gt manufacturer 65535 GDB 09 43 00 gt product 65535 GDB 09 43 00 gt version 1 1 GDB 09 43 00 gt name USB Audio Device 2 GDB 09 43 00 gt Midi Out 2 of 5 name USB Audio Device 3 GDB 09 43 00 gt MIDI Out device 2 GDB 09 43 00 gt manufacturer 65535 GDB 09 43 00 gt product 65535 GDB 09 43 00 gt version 1 1 GDB 09 43 00 gt name USB Audio Device 3 GDB 09 43 00 gt Midi Out 3 of 5 name USB Audio Device 4 GDB 09 43 00 gt MIDI Out device 3 GDB 09 43 00 gt manufacturer 65535 GDB 09 43
22. GU PairlightaDProjectsiMew Projectiz iNew Project12 DR 2 LIB 1 37000 G FairlightAUiFProjecksiNew Projectiz iNew Project12 DR2 LIB 1 Ug Gi Fairlight Projects Wew Projecti21Mew Projectiz DRZ LIB 1 Cog G Fairlight amp UiProjects Mew Projectiz iNew Projectl BR LIB 1 El Multiple reels can be selected at the same time and linked to a single project Step 6 Set up destination tracks If all tracks will be involved choose Track 1 as the destination Step 7 Click the Reconform button If one of the linked projects is not found an error message will be displayed and the reconform will stop If there is no audio between the source In and Out times for an event an error Pyxis G2 Page 95 Operator Reference Manual CHAPTER 11 EDL MANAGEMENT September 15 2011 message will be displayed but the reconform will continue with the following events Additional Facilities Selecting a reel in the Reel Linking dialog also selects all of the EDL events associated with that reel Clicking the A button in the Sort group causes the EDL events to be sorted according to the EDL event numbers Clicking the C button in the Sort group causes the EDL events to be sorted according to source reel Pyxis G2 Page 96 Operator Reference Manual CHAPTER 12 LINK GROUPS September 15 2011 Chapter 12 Link Groups Introduction Link groups are designed for controlling groups of Tracks in multichannel formats Link groups simplify many tasks a
23. Manual CHAPTER 8 EDITING September 15 2011 Erase Tail Hestore Head Restore Tall Ciee Multi Channel Clips Set Clip Colour Hint if you want to see all the layers select Edit gt Display Layering Razor Sometimes it is useful to cut the time out of a track not just the audio This is similar to cutting tape To cut time as well as audio turn on the Razor button This will automatically turn on Range and All Layers As soon as you cut something Head Tail or Range the time they occupied is also cut and all the following clips move earlier When you paste click Paste with Razor switched ON the clipboard audio is inserted into the track pushing all the following clips later This is true even if Razor was not ON when the clips were cut to the clipboard cut and Paste are really independent commands each responsive to the Razor setting Pyxis G2 Page 68 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Copy Copy works exactly the same way as cut except that the audio is not removed to place it on the clipboard only copied Pasting after copy is the same as after cut Erase Erase works exactly the same way as cut except that the audio is not placed on the clipboard The clipboard remains unchanged so its previous contents are ready to paste at any time Extra Edit Commands The following extra buttons are available when the cut Copy Or Erase modes are current split clip Cuts t
24. Microsystems Inc has contractually obligated Fairlight AU s Software Suppliers to make this disclaimer e No Liability for Certain Damages EXCEPT AS PROHIBITED BY LAW Fairlight AU S SOFTWARE SUPPLIERS SHALL HAVE NO LIABILITY FOR ANY INDIRECT SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE IN NO EVENT SHALL Fairlight AU S SOFTWARE SUPPLIERS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U S TWO HUNDRED FIFTY DOLLARS U S 250 00 e Limitations on Reverse Engineering Decompilation and Disassembly You may not reverse engineer decompile or disassemble the SOFTWARE except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation e SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device and only if the recipient agrees to this EULA If the SOFTWARE is an upgrade any transfer must also include all prior versions of the SOFTWARE Obtaining Technical Support Users requiring technical support should contact their local distributor Information can also be found on the world wide web at http www fairlightau com Manual Errors and Omission To help ensure that Fairlight provides the most accurate and comprehensive documentation pl
25. Mouse Edit Menu The screen Edit Menu provides many commands that are available elsewhere in the system The mouse can be used to access these commands Pyxis G2 Page 83 Operator Reference Manual J Ctril 7 Ctrl Y Undo Redo Undo List Cut Ctri X Cut Head Cut Tail Copy Ctrl C Copy Head Copy Tail Paste Ctri V Erase Erase Head Erase Tail Restore Head Restore Tail Join Split Cleave Multi Channel Clips Remove Hidden Clips Split Clips ctri s Clip Level Rename Resync to record time Reverse Clips Rotate Layers Set Sync Point Range All Layers Razor On Range Selection Snap Editing Snap To y y Jump To Pyxis G2 CHAPTER 8 EDITING September 15 2011 Undoes the last edit Redoes the last edit that was undone Shows a list of the edits that can be undone Cuts the selected clip or range to the clipboard Cuts the head of the clip at the cursor position Cuts the tail of the clip at the cursor position Copies the selected clip or range to the clipboard Copies the head of the clip at the cursor position Copies the tail of the clip at the cursor position Pastes a copy of the clipboard at the current position Erases the selected clip or range Erases the head of the clip at the cursor position Erases the tail of the clip at the cursor position Extends the clip head to use all the recorded audio Extends the clip tail to use all the recorded audio Heals separation in audio clips Unlinks multicha
26. New button that appears below If there is already a project open the system will ask if you want to save it Step 2 The system displays the New Project dialog Project Type Folder D FairlightAU Projects Create Project in New or r Subfolder Project Name New Projects Video Sample Rate Hz Frame Rate Step 3 Fill in the form presented by the system Project Name The name you enter here cannot be changed before saving the file though it is possible to Save As under a different name It is also possible to rename the project as explained below Comment Put any text in here for your convenience It will be shown at the top right of the screen Pyxis G2 Page 19 Operator Reference Manual CHAPTER 3 PROJECTS September 15 2011 Sample rate The system supports sample rates up to 96 kHz This is set now when the project is created and cannot be changed thereafter Frame Rate The value you place here can be changed in the Sync display at any time afterwards It should match the incoming timecode format for correct synchronisation Video Add Pyxis Track If this is checked the system will display a video track at the top of the track display Audio Tracks Choose the number of tracks you would like in the project This cannot be changed later Step 3 Click OK to create the project Closing a Project Use File Y Close If you have changed anything since opening the project the system will ask if you want
27. Other Places a My Network Places My Documents E Shared Documents g Control Panel Designating Media Device When Pyxis G2 is first started it displays a dialogue box requesting that a default project device be selected Select the devices Audio and Video you wish to use from the list of available drives To prepare the drive for use with Pyxis G2 select Setup gt Media and Project Management from the Pyxis G2 main menu Select the device from the devices list and click on Convert to Media device Please also set the Device Info accordingly in most cases this is set automatically and does not need to be changed Pyxis G2 Page 135 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 Devi Media Space kb cal cal Dream II Both 15178720 Yes 2500 Local Yes 0000000 Rs Rs Dream II Audio 212907624 Yes 500 Shared Yes 0000000 Both 619719412 2500 Shared Yes ooo0000 Convert to Media device Set Device Info Default Project Device C Device Mame Pr Device Speed Fast i Normal Slow Device Type Local Network shared Temp Click here for Format f Dream folder display Guid To use a network connected device first create a mapped network drive or folder in Windows Explorer This can now be selected in the device panel and converted to a DREAM II Media Device as above Please note that audio and video files can only be played from
28. September 15 2011 Step 1 Make sure that a Pyxis track is displayed If not see above Step 2 Open Windows Explorer or My Computer and find the video file you wish to import Step 3 Drag the video file from the Windows Explorer window and drop it on the video track in the Dream IT Edit Screen The following file types can be imported using drag and drop e Quicktime mov e Avi avi e Windows media format wmv e Mped 4 files mp4 e Mpeg 1 20r3 mpg m2v mvf e dv25 dv or dif e MXF mxf containing dv25 dv50 dvi00 DVCPro HD or IMX mpeg compressed video e Omf video files omf containing mjpeg dv25 or uncompressed video e Thomson Grass valley dv25 files vid e Bitmap files single still image bmp useful for a clapper board also any Dream Pyxis native files which are e uncompressed vmu e dv25 dif e mjpeg vmj e lossless Huffman compression vmh MXF files require an MXF licence dongle IMX Mpeg requires an IMX Mpeg licence Dv50 dv100 require a DVCPro Licence dongle Playing a QuickTime or AVI file requires that the latest available codec for that file type has been installed Fairlight recommends that automatic update be switched on to ensure that the version remains current In some cases a specific codec must be installed e g QuickTime files from Avid require the Avid codec to play them For a good indication of playability double click a file in Windows Explor
29. You can then start typing the timecode number from that field Enter Locate Time 09 58 02 10 Pyxis G2 Page 104 Operator Reference Manual CHAPTER 15 GO TO September 15 2011 2 The up and down arrows on the QWERTY keyboard can be used to increase or decrease the current timecode field by one Go To Clip Name The Go to Clip function locates the transport to the head of the desired clip It also incorporates an alphanumeric search function to help sort through clips by name Step 1 Use the command View 3 Clip Search Step 2 The Clip Search dialog is displayed You can shorten the list by typing a sequence of characters in the text field at the lower left Only clip names containing that sequence will be shown so as you type more characters the list will get shorter and shorter Step 3 Select the desired clip using the mouse Step 4 Press Enter to locate to the selected clip The Clip Search Dialog Clip Color Track Layer Start Time End Time Duration a Closer new 03 Track 22 1 09 50 24 07 09 50 33 05 00 00 05 3 Closer new 03 Track 60 1 09 50 24 07 09 50 33 05 00 00 08 23 Closer new 03 Track 98 1 09 50 24 07 09 50 33 05 00 00 08 23 621 My Name Is Frank_ Track 9 1 09 50 27 06 10 04 19 15 00 13 52 07 621 My Name Is Frank_ Track 10 1 09 50 27 06 10 04 19 15 00 13 52 07 621 My Name Is Frank _ Track 47 1 09 50 27 086 10 04 19 15 00 13 52 07 621 My Name Is Frank_ Track 48 1 09 50 27
30. a designated Media Device If you try to play files from any other disk you will receive an error message Controlling Scanned Folders You may wish to save time when the system starts by omitting the scan of some folders in your system This is particularly useful when the system is connected to a network Clicking the downward facing v shown above expands the display to show folders as seen below Pyxis G2 Page 136 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 Devices Name Location Description Media _ R w_ Free Space kb FairlightAU For Networked Perm Guid Audio_D D Dream II Audio Riw 104485040 Yes 2500 Local Yes 0000000 Yideo_E Ed Dream II Video Rw 175163476 Yes 2500 Local Yes 0000000 Local Disk En Windows Forma Both RiwW 32375516 No 2500 Local Yes N A Yault TA Windows Forma Both Riw 409753720 No 2500 Shared Yes N A Rec Priority DU Z Find SubFolders Convert to Media device Set Device Info View CD Drives Default Project Device Audio_D Rescan Devices Devices E Show Hide Folders and Projects Scanned Folders Subfolders D FairlightAU Projects NLY Diana frango Pyxis NLY 8 24000 clip project DR2 Dream II 2404 Big Import DR2 Dream II 5678 Frank MixO05 DR2 D rc11 Testing 1140 New Project19 DR2 Dream IT 1548 New Project20 DR2 Dream II 10 Plugin builder DR2 XXXXX xxx File D FairlightAUProjects Pl
31. also tally the changes MIDI Devices For HUI to work the Xynergi system must know which MIDI devices to expect These are written into the file HUISetup txt which is normally found here C Program Files Fairlight FMC Data Open the HUISetup txt file It already contains the necessary setup for three HUI devices a Roland Edirol interface a MOTU Microlite 4 port MIDI interface and a Tranzport controller this is for wireless control of basic functions only If you want to make life easy for yourself buy an Edirol or a MOTU Microlite and just enable it by removing the hashes in front of the lines in HUISetup The following procedure assumes you have some other kind of HUI controller Your task now is to find out the names of its MIDI ports and write them into the HUISetup file in the same way as the existing entries If this sounds too complicated get your Fairlight service provider to help it s a one time setup in most cases First you ll need to identify the MIDI devices attached to your system Connect your HUI controller via MIDI or USB To see a list of the MIDI devices seen by Dream II we ll use our debugging program Pyxis G2 Page 149 Operator Reference Manual CHAPTER 23 HUI SLAVE MODE September 15 2011 MSAT Start MSAT before starting FMC the Mixer program If Dream II is already running stop FMC as follows Step 1 Click on the Mixer screen to give it focus Step 2 Type ctrl Shift 0 Step 3 Type y to c
32. and Alt monitor sets follow the steps below Step 1 Click the Monitor Setup button in the Setup megamode The system displays the Monitor Setup dialog 0 0dB 0 0dB P le CR_MON L CR_MONC CR_MONR CR_MONLs CR_MONRs CR_MONB Sx20 AO1 SX20 402 X x Patch aa sueros so 105 sueros sueros sueros sueros gt 581045 sus sot 98100 a0 aoe Studio Increase Monitor 1 Format Rename Step 2 Click one of the Speaker Sets MAIN or ALT Step 4 To determine the number of outputs required you must specify the format of the speaker set Click the Increase Format button to cycle through the available formats These are Mono Stereo LCR LCRS LCRSS 5 1 Step 5 Select the type of physical output you wish to patch to by clicking Analog Outputs OF Digital Outputs Step 6 Select one or more speakers in the upper left Step 7 To patch outputs to the selected speakers select the same number of outputs and click the Patch button Step 8 To name the selected speaker set click the Rename button type a name and press the Enter key Pyxis G2 Page 125 Operator Reference Manual September 15 2011 System Outputs Specific outputs may be defined for use with control room monitors only System output ports are only available for patching in the Monitor Setup Patching page System ports are defined in the I O Config TXT file as described in The I O Config TXT File on page 229 Use system output ports for patching your control ro
33. any clip to locate to its timecode Pyxis G2 Page 105 Operator Reference Manual CHAPTER 15 Go To September 15 2011 Select the Under Playhead checkbox to display only clips touching the cursor This is updated as the transport moves the Pop button to bring the currently selected clip to the top layer on its track This can be used to manage multiple takes of the same recording layered on a single track Select the only Offline Clips checkbox to reduce the list to only those clips for which media are not currently available Click the Reveal File button to display a Windows Explorer window showing the file containing the media for the clip Resize the dialog by dragging with the mouse on any of its sides Change the order of displayed fields by dragging the field names horizontally with the mouse The Clip Search dialog can be displayed at any time using the Edit Screen menus View 3 Clip Search This allows you to keep it on the screen while you do other types of editing Go To Mark The Go to Mark function locates the transport to any stored Mark that you have created Step 1 Step 2 Step 3 Step 4 Use the command View Marks The Marks dialog is displayed Use the mouse to click on the desired mark Click Jump to locate to a mark or double click the mark While viewing the list of marks you can also select and edit them changing their names and timecode locations While marks are displayed you can
34. be used to visually locate an important moment To change the sync point press sync point at the new location There is only one sync point per clip Pyxis G2 Page 70 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Trim Edit Options Trim is usually applied to a single clip or selections across tracks therefore no options are available Range On is not supported in Trim Mode All Layers On is not supported in Trim Mode Razor On is not supported in Trim Mode Nudge The Nudge function slips clips by one frame in either direction Nudge can operate on one or many tracks affecting clips that lie under the cursor or within a Range Using Nudge Step 1 Press the Nudge button Step 2 Locate the cursor over the clips and select the appropriate track s Step 3 Press the Nudge Left or Nudge Right button to slip the clip s by one frame SE Nudge Left pay A Nudge Right LLL When there is no Range only the top layer of clips highlighted under the cursor is nudged Nudge with A Range Follow these steps to perform a NUDGE with a range selected Step 1 Press the Nudge button Step 2 Use the From and To buttons to select a Range that includes all clips to be nudged Step 3 Press the Nudge Left or Nudge Right button to slip the clip s by one frame When a Range is selected all layers of clips within the Range are nudged including those which are completely buried NOTES Nudging is possible whi
35. change permanent Page 87 Operator Reference Manual CHAPTER 10 CLIP EQUALISATION September 15 2011 Chapter 10 Clip Equalisation Introduction Pyxis G2 provides clip based four band parametric Equalisation plus shelving which can be applied to a single clip or range of clips within a Project EQ is performed by the system in real time as the audio is output from Pyxis G2 therefore applying an EQ change does not af fect the audio data on disk Clip EQ is controlled from the Smart Pane To access it use View Smart Pane Clip EQ Dis Layeril ing Audiobase Show Pyxis Track Clip EQ lt Playback Video Source Cross Fade Edit Workspace Machine Control Marks Sync Setup sa Curves Sort Video Locators Tracks Clip Search TimeScale Background Tasks Performance Sta tistic 5 Transport Window Timecode Display Software Keyboard Applying EQ Step 1 Open the Clip EQ Smart Pane see above Step 2 Locate the cursor over the clip or define a Range of clips Step 3 Click the edit button 21 Band Gain a AF EN TH E 7 A HMF 3500 0 0 col al oe A m o A El a a e 20 Step 4 Select the appropriate EQ parameter This is done by clicking in the appropriate field in the EQ display above Step 5 Adjust the parameter by typing a value on the QWERTY keyboard and pressing its Enter key Changes are heard in real time You can also use the up and down arrows to cha
36. choose how many tracks will be in the project when you first create it starting the System Step 1 Start the host computer PC by turning on its power switch The PC will boot the Windows operating system and display your PC desktop Step 2 Power on the audio interface box es SX 20 and optional SX 485 Step 3 Start the Dream II application by double clicking its desktop icon or by selecting it in Start Y All Programs Fairlight Pyxis G2 Y Pyxis G2 Pyxis G2 Page 16 Operator Reference Manual CHAPTER 2 PYXIS G2 OVERVIEW September 15 2011 system Shutdown Step 1 Exit Pyxis G2 by selecting Exit from the File Menu or by the keystroke combination Alt F4 Step 2 If a project is open the system will prompt you to save any changes that have occurred since it was opened xl l P The current project has been modified Would vou like bo sawe it now E Eo Cancel Click Yes if you want to save the changes in the project This may take a minute or so during which a progress bar will grow in size Organising Your Screen Pyxis G2 normally fills the monitor screen expanding automatically to fit Note Screen bit depth MUST be 24 bit If you wish it to reduce its size edit the Pyxis icon that you use to start the system as follows Step 1 Right click the icon you use to start the system It looks like M ER Step 2 Select Properties from the menu of commands Step 3 Select the Shortcut tab if not already
37. correctly To enable backup saving issue the command Setup gt General Preferences and go to the Projects tab General Preferences x Options Audiobase Playback Video Capture Projects Audio Plugins Number of Backups E Sutosave Load Last Project on Startup D Set the number of backups you would like to keep The system default is 5 which means the 5 most recent saved versions of your file will be retained Automatic File Saving Automatic File Saving allows you to save your project automatically at regular time intervals To set this up issue the command Setup General Preferences and go to the Projects tab Pyxis G2 Page 133 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 General Preferences xX Options Audiobase Playback Video Capture Projects Audio Plugins Number of Backups E Load Last Project on Startup D Set the desired interval for Auto Save or turn it off Note When the time for an Auto Save arrives it will wait until the transport is stationary then take control of the system While saving it will prevent the transport from starting and mute all audio at the outputs This is necessary to prevent unwanted interaction with the automation system Undo Files Pyxis G2 allows unlimited UNDOs for audio editing It does this by storing a copy of the Edit list each time an edit is made The undo files are stored in the fol
38. displayed waveforms to be amplified and attenuated independently of the audio levels The gain changes are performed by the system in real time as the audio is played out from the system Applying a level change to a clip does not affect the media on disk The level function can operate on multiple tracks on clips that lie beneath the cursor and also within a Range Applying a Level Change Step 1 Click the Level button p IU Razor I V imi Nudge Level a off a a a Step 2 Select the track or tracks containing the clips you wish to modify Step 3 Locate the cursor over the clip s or define a Range that wholly contains the clips Step 4 Press the set or Trim button Step 5 Change the level by typing in a value between 100 and 100 dB If Trim was pressed the amount is a level offset for the selected clips To enter a negative number type a minus first You can alter the number in 0 1 dB steps using the up and down arrows on the QWERTY Step 6 Click ox to make the change permanent or Cancel to escape with no change The output of each track is displayed on the level meters Range A number of clips can be altered at the same time using a Range and track selection A range is created using the From and To buttons When using a Range only clips that are entirely within the Range are affected NOTES It is possible when using the Level Menu to push the level of a clip over digital full scale Check the meters to set th
39. double click on any item to locate to its timecode Pyxis G2 Page 106 Operator Reference Manual CHAPTER 15 GO TO Video Locator 18 Video Locator 19 Video Locator 20 Start of audio Video Locator 22 Video Locator 0 Video Locator 23 Video Locator 130 Video Locator 24 Video Locator 25 Video Locator 26 Video Locator 27 Video Locator 26 Video Locator 29 Video Locator 30 Video Locator 31 Video Locator 32 Video Locator 33 Wideo Locator 434 Video Locator 35 Video Locator 46 Video Locator 49 Widen ocator 45 Pyxis G2 10 a2 2 OOS Sei 21 10 04 05 04 10 04 11 05 10 04 10 10 04 143102 10 04 43 0 10 05 0 05 10 05 0 05 10 05 0 05 10 05 0 05 10 05 0 05 10 05 6 05 10 05 0 05 10 05 lt 8 05 10 05 0 05 10 05 6 05 10 05 0 05 10 05 8 05 10 05 0 05 10 05 0 05 10 05 28 05 entero Set Time Jump To Rename Remove Remove All hd Close Page 107 September 15 2011 Operator Reference Manual CHAPTER 16 ADR September 15 2011 Chapter 16 ADR Introduction Pyxis G2 provides the ability to automate recording using a list of In and Out points with a simple interface The ADR menu includes functions for setting pre and post roll and features for automatic dialogue replacement The ADR List The ADR List allows you to set up a list of recordings cues that you want to take Each one has a controlled In and Out point and tex
40. fades can be achieved as follows Step 1 Select a track and move a clip under the cursor Step 2 Click the Fade button if not already on Step 3 Click the Head button This creates a fade from the start of the clip to the cursor position The shape of the fade can be seen above this will be described later but the Duration is not used Instead the duration is set by the cursor position If you are happy with your current fade shape using Fade Head is a fast and simple way to get a lot of work done NOTES e If you do not want to apply the Smart Panel shape shown above to the Head turn off the shape checkbox in the Smart Panel e If you ONLY want to apply the shape and not to change the length of the head fade turn off the Length checkbox Pyxis G2 Page 72 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Fade Tail Same as Fade Head but it fades from the cursor to the end of the clip Fade Clip Applies the numbers in the Head Duration and Tail Duration fields shown in the Smart Pane 10 20 30 40 so 60 70 30 90 o o No 30 40 50 60 70 80 30 100 y T f o 10 10 of 00 00 00 D8 10 I 00 00 00 20 gt be 1 Duration Duration 50 50 50 350 Using Multiple Tracks If multiple tracks are selected the simple Fade Head and Fade Tail commands will apply to all clips touching the cursor on selected tracks Using a Range If a Range is present the Fade Head command applies the He
41. in the following order If 2 Feeds are linked they are panned L R If 3 Feeds are linked they are panned L CR If 4 Feeds are linked they are panned LCR S If 5 Feeds are linked they are panned LC RLS RS If 6 Feeds are linked they are panned LC RLS RS B If 7 Feeds are linked they are panned LC RLS CS RS B If 8 Feeds are linked they are panned LLC C RCR LS RS B Normally each member is panned hard to one Bus Element position spread is set to maximum divergence is set to minimum and rotation is set to zero If you are using a link group to control a premixed stem which is delivered in a different channel order it may be necessary to edit the track order on the disk recorder or to change the input patching of the feeds if the stem is played in off an external device Destroying a Link Group Link groups are destroyed from the Link Group Dialog Pyxis G2 Page 99 Operator Reference Manual CHAPTER 12 LINK GROUPS September 15 2011 Step 1 Click the Tracks button in the Edit megamode Step 2 Click the Track Format button The system displays the Link Group dialog Step 3 Click a Track in a Link Group to select the Group Step 4 Select Unlink Or Unlink and Reassign from the commands at the right Unlink gt unlinks the members without reassignment Unlink and reassign gt unlinks the members If the Link Group had a Boom member that was de assigned from all other Bus Elements it is reassigned to them To close the dialog
42. matter Step 3 Move this file to a Media Device The simplest is to move it to the folder on your audio drive where the original project is stored Pyxis G2 Page 134 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 Step 4 Open this file by issuing the File Open command or using the Project Menu open soft key Video Files Pyxis G2 supports drag and drop import of a variety of video file formats as well as direct video recording to the Pyxis G2 timeline For correct operation video files must be played from and recorded to a separate hard disk than the audio data WARNING If you attempt to play video and audio data from the same hard disk you will experience SEVERE performance problems The disk bandwidth required for video is governed by the type of video you wish to play back Some types of compressed Standard Definition video may play back from a single 10 000 RPM SATA drive while uncompressed High Definition Video may require a large fast RAID array Please contact your Fairlight distributor to discuss your specific needs Typical Pyxis G2 Drive Configuration F F My Computer File Edit View Favorites Tools Help T eo Ban Back gt Ba A Search ey Folders 555 Address 4 My Computer ka Ga System Tasks Sel Local Disk 01 Set Audio De View system z Video En information l D a shared Documents programs 5 Dream s Documents pe Change a setting
43. most powerful format and the other two support earlier systems and their software Pyxis G2 Page 22 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 Chapter 4 Audio Tracks Transport Introduction Pyxis G2 provides up to 192 disk recorder tracks routed via dedicated track feeds It supports up to 256 analog and digital inputs and outputs which may be patched to tracks as required see Chapter 7 Patching and Assignment for more details on patching In addition Pyxis G2 provides a video track and with the appropriate graphics card installed the means to capture video directly Displaying Tracks Number of Tracks Disk recorder tracks are displayed on the screen Select the number of tracks to display using the Track Number selectors shown below Click on the numbered buttons to control how many tracks are displayed For example click on 8 to see 8 tracks on the screen Note that when the Video Track is switched on it is counted in this number Click the Up Arrow button to move the track display upwards For example if Tracks 5 to 8 are currently displayed clicking Up will cause Tracks 4 to 7 to be displayed Click the Down Arrow button to move the track display downwards Click the Top button to move the display to the top e starting at the Video Track if switched on otherwise at Track 1 Pyxis G2 Page 23 Operator Reference Manual CHAPTER 4 AUDIO TRACKS a
44. now Set Display Level Select All Viewed Tracks Enforce When you choose a track colour all clips on the track that currently have its old colour are given its new colour This applies to all clips for which you have never explicitly chosen a colour Choosing Clip Colours To explicitly choose clip colours do the following Step 1 Select tracks containing the clips you want to colour Step 2 Move the transport so the clips are under the cursor or make a range using the From and To keys The clips should be red Step 3 Use the menu Edit gt Set Clip Colour Pyxis G2 Page 25 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 Edit Undo Ctri Z Redo Ctri Y Undo List Redo List T7 Cut Ctri X Cut Head Cut Tail Copy Ctrl C Copy Head Copy Tail Paste Ctrl Paste Special Erase Delete Erase Head Erase Tail Restore Head Restore Tail Solit Clips 5 Join Split Cleave Multi Channel Clips Restore Multi Channel LR Stereo Swap BF j Rotate Layers Reverse Rotate Layers Space Clips Evenly Group Clips UnGroup Clips Set Clip Colour gt Clip Level Click to choose a colour for all selected red clips Phase Invert Clips Rename Resync to record time There are two extra EAS AN Reverse Clips PO colours just for clips useful for reminding AAA you that they need attention Set Sync Point Flip Yideo Clip Field Click to retur
45. playing less than all of the original recording This will be the case if the clip was imported with handles or if the original clip has been edited Head Trim Head and Trim Tail are the most common uses of Trim Step 1 Step 2 Step 3 Step 4 Step 5 Select a track and move a clip under the cursor Press the Trim key on the if not already on Press and release the Head key Move the transport forward a few frames jog or play Press Enter The head of the clip is placed at the cursor which is now shorter The effect is just like erasing the head of the clip Its sync remains as before but it starts at a later time and a later point in the audio Step 6 Jog backward a few frames and press ENTER Now the head is moved earlier revealing more of the audio You can keep jogging and pressing ENTER as long as you like until you are satisfied with the position of the head Limit to Trim When extending a clip the end of the recorded audio will be reached eventually After that it is not possible to extend the clip further Tail Same as Head but the later part of the clip is trimmed Range Ranges cannot be used with Trim Multiple Tracks Works as expected All the red clips will be trimmed to the same point in time Soft Keys in Trim Mode sync point Pressing the sync point soft key creates a sync marker within the selected clip s at the cursor position This is shown as a yellow mark in the clip and can
46. save it Step 2 The system displays a list of all the projects in the last folder you visited If necessary browse to other folders to see other projects that you may wish to open A Select project file to open Desktop SD My Documents sr My Computer de My Network Places Step 3 Click on the name of the Project you wish to open then click the Open button The system will load all of the audio and reconnect to external files that were used last time in the project Pyxis G2 Page 18 Operator Reference Manual CHAPTER 3 PROJECTS September 15 2011 Opening a Recent Project Pyxis G2 keeps a list of your most recent projects To open one of these click File in the Menu Bar Be Edt Edit Settings view Tracks Fades Setup ur four most recent projects are shown at the bottom of the menu list Simply click on one of them to open it again Opening Files Across the Network If your Pyxis G2 system is part of a PC network the system will allow you to open a Project located across that network for example on a server In this situation the number of tracks that can be played may be limited depending on network bandwidth and other traffic In addition the response of the system may be slower than usual For best performance it is always best to locate projects on the local hard drive in your Pyxis G2 PC Creating a New Project Step 1 Click the Project button at the right of the screen then click the
47. selected Step 4 Edit the text in the Target text box Normally it reads as follows C Program Files Fairlight PyxisG2 Pyxis G2 exe Change it to C Program Files Fairlight Pyxis G2 Pyxis G2 exe HEIGHT1680 WIDTH1050 but use your own numbers for desired height and width Step 5 Click OK and restart the application Using the System Follow the instructions in the following chapters to quickly learn all the operating procedures necessary for completing production tasks with Pyxis G2 Pyxis G2 Page 17 Operator Reference Manual CHAPTER 3 PROJECTS September 15 2011 Chapter 3 Projects Introduction Pyxis G2 uses Project files to store your work All audio recordings editing and file imports are done within Projects A project contains all the edit information plus Pyxis G2 settings as well as links to the audio and or video files that have been incorporated into the project Edits performed on the audio and video data are non destructive and are represented by clips which refer to pieces of audio or video data As with other standard Windows applications Projects must be saved to disk before being closed or all changes since opening will be lost Project files are given the pR2 filename extension by default Opening a Project Step 1 Click the Project button at the right of the screen then click the open button that appears below If there is already a project open the system will ask if you want to
48. signal Under normal conditions this will be Decklink Video Capture Input Source is currently not activated Setting the correct Video Input must be performed within the Decklink Control Panel See above Record Format is the video file and codec format for capturing the incoming video signal The options available are e DV25 DV Codec 3 5Mb sec SD NTSC or PAL ONLY e MPIEG e Uncompressed Pyxis G2 Page 43 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 e Huffman Lossless For Standard Definition systems DV25 is the recommended setting For High Definition systems Huffmann Lossless is a good reliable option Invoke Video Capture Mode Unlike an audio recorder digital video capturing equipment must be in a specific Video Capture Mode in order to record an incoming signal In DreamII you can invoke this mode by navigating to Setup Y Video Capture Mode Setup General Preferences Patching Monitoring TF Load Mixer Template Link Groups Locked Playhead Reset Playhead Bars and Beats Setup Media and Project Management Flip Decklink Field Order M_JPEG Compression Wideo Capture Mode Dpx Parameters With Video Capture Mode ON your Decklink card will act as a loopthough device and will display the incoming video signal This is in contrast to its normal mode where the Decklink card displays whatever video is already on the Pyxis
49. the source machine outputs to some of your DREAM II inputs and use the Patch I O page to patch them through to the recording tracks The Patch I O page is discussed in detail in Chapter 5 Patching and Assignment Set up Destination tracks for Conform The Destination tracks are those to which the audio will be copied to match the Rec Start time for the EDL events You need only specify the first destination track the software uses the following tracks to place audio for events requiring more tracks Click the Capture button The EDL Capture and Conform will now go ahead The software will request the first source reel to be loaded on to the source machine x P Please load reel ANIMAL_L Is this reel loaded It will then capture all the audio needed from that reel optimizing to reduce the amount of shuttle time The software will then request the next reel and continue in this vein until the conform is complete Events that cannot be recorded are marked E Error Reasons for this can include Bad timecode causing lost sync before the end of a recording Tape machine not locating to the pre roll point The software will continue after errors of this type and complete as much of the Pyxis G2 Page 94 Operator Reference Manual CHAPTER 11 EDL MANAGEMENT September 15 2011 conform as it can Reconform Reconform uses an existing project or more than one project as the source audio for a Conform There is no
50. to cur or copy the clip before locating to the desired frame Pyxis G2 Page 148 Operator Reference Manual CHAPTER 23 HUI SLAVE MODE September 15 2011 Chapter 23 HUI Slave Mode Introduction HUI is a protocol invented by Mackie Corporation which allows different audio systems to control each other Many consoles and other devices now incorporate aspects of the HUI protocol and Constellation XY has implemented the full specification as a slave including the Universal Pro Extensions This allows the following functions to be controlled remotely e Transport states including Jog and Shuttle e Jog Frames i e the system can be jogged remotely e Fader levels bidirectional for motor control e Mutes Solos Track Arms Channel Selects note Channel Select will arm a track if the Arm or ADR menu is current e Channel names the first 4 characters to be displayed on the controller e Buttons on the controller can be mapped to Dream II functions Setup Install HUI device Your HUI device will come with its own installer cables and instructions Follow these and make sure the HUI device is working correctly INI File The file C Program Files Fairlight FMC FMC ini must contain the line HUI Where nis the number of faders on the HUI device default 8 Just doing this will result in faders mutes pans solos and selects from your HUI device working correctly on the Xynergi system That is to say they will act and will
51. track Note If no Decklink card is fitted your system cannot operate in Video Capture Mode It can however play back video files 00 00 00 00 With Video Capture Mode ON you may ARM the Pyxis track and record the incoming video signal in the same way as you would record audio displaying your video use the command Pyxis G2 Page 44 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 View Pyxis Display Layering Show Pyxis Track Playback Video Source Edit Workspace Locators Sort Video Locators Tracks Clip Search TimeScale Statistics Performance Background Tasks This window is resizeable and can be made to go full screen with a double click on the window with your Left Mouse Button video locators Eii 00 00 26 19 O000 28 22 20 00 40 06 y em y peee ae ea m 2 gt a Click here to 0000 51 17 000011421 00 00 22 20 scroll video locators list Video Locators While the Pyxis window is displayed you may click on an empty Video Locator at any time This will capture the current video frame and display it with a timecode number To locate to any Video locator Limply click it To re order the locators drag and drop them with the mouse To delete a locator drag it far to the right and drop it when the delete icon is displayed Video locators are also displayed in the Edit Marks list Locators list and can be edited there See Go To Mark page 105 The Video Sc
52. u Disables stop on wrong USB driver message FMC will still check the drivers still report out of date drivers and will still say that it can t continue but it will continue anyway BLUE Utils Menu The BLUE utils menu offers the Update Sys File item for storage of system settings System Files are stored in the C Program Files Fairlight FMC Data directory Step 1 Hold down the BLUE key and press the utils key to enter the Utils menu Step 2 Press the Update Sys File soft key to store the system settings This information is stored in the following files Monitor_Sources TXT patching and formats of external monitor sources Speaker_Sets TXT patching and formats of all speaker sets Setup_ Variables TXT Call Follow state and Pyxis G2 brightness Pyxis G2 Page 162 Operator Reference Manual CHAPTER 25 SPECIFICATIONS September 15 2011 Chapter 25 Specifications Audio I O Configuration See SX 20 and SX 48 installation guides for details Pyxis G2 Wiring and Connection Details The following information contains all the wiring details necessary for specifying studio cabling installations Connector sex described is the panel mount connector on the rear of the Pyxis G2 Meter USB Description USB and DC Power connection for external meters Note that Sidecars do not require DC power Cable must be shielded and less than 3 meters in length Connector 5 Pin XLR Female majowe CNE 1 SHELL SHIELD 1
53. video if licensed to do so and equipped with very fast hard drives The sample rate of the audio is shown at the right This is set when a Project is first created and cannot be changed thereafter The next display shows which system hard drive is being used for Audio recording at the moment in this case D Drive The number to its right shows the time available for recording on the currently armed tracks of course it will reduce as you arm more tracks and as you record more audio The leftmost number in this case 178 is Hours The machine status indicator in this case 9pin Master is the selected type of the first machine M1 The M1 M2 and M3 buttons can be used to enable three different machines which can be synchronised if properly set up See Chapter 22 Machine Control for details Editing Tools Pyxis G2 Page 14 Operator Reference Manual CHAPTER 2 PYXIS G2 OVERVIEW September 15 2011 The editing tools provide single button commands for editing audio and video clips Mouse editing is also available Transport Controls The central group of buttons shown above does exactly what you expect namely Rewind Fast Forward Play Stop and Record Both Rewind and Fast Forward can be clicked repeatedly for increased speed Record is a single press button and can be entered from any transport state The leftmost group of buttons shown immediately above works as follows z Jump Left pressing this butt
54. well Pasting Pasting the clipboard use the Paste button means putting a copy of it at the current position on whatever tracks are selected You can paste the clipboard contents at any time not just after a cut operation and as often as you like If there are already clips at the place where you paste the clipboard is placed on top of the existing clips Only the top layer is heard unless there is a crossfade between layers more about that later The shape of the clipboard s track selection is preserved when pasting regardless of track selection at that time For example if you copy clips on tracks 1 and 3 then select only track 8 and click Paste the clipboard will be pasted on tracks 8 and 10 The first track on the clipboard is always pasted on the lowest numbered track in the selection Variations There are a few extra keys which change the functions of Cut and Paste All Layers Sometimes clips are stacked in layers Of course we only hear the top layer or crossfades between the top and second layers more about crossfades later You have the choice of cutting only the top layer or all the layers The 211 Layers command controls this choice When it is on you will cut all the layers and they ll be placed on the clipboard ready to be pasted When it is off you will cut only the top layer To turn on all layers use the menu command Edit gt All Layers Pyxis G2 Page 67 Operator Reference
55. 000 a E CLOSE D MAIN RE C 53EP12 D C 538P12 li c A12 S3EP 12 11 D A12 12 BL 12 A 34 BL 12 D A34 12 S3EP12 13 c A 34 S3EP 12 13 D A34 25 BL i4 c A12 53EP11 15 c A12 S3EP 11 15 D A12 i2 34000 Pyxis G2 00 46 21 14 00 00 00 00 O00 14 38 12 00 47 24 12 00 16 55 25 00 16 55 24 18 28 13 17 00 48 26 11 19 00 51 10 00 1224 20 00 13 13 22 00 13 54 02 00 00 00 00 00 00 00 00 00 17 32 09 00 17 33 06 00 00 00 00 00 07 30 20 00 09 30 24 18 28 13 11 00 48 37 05 00 00 00 00 00 16 55 12 00 48 26 11 00 16 55 24 00 16 55 24 16 28 16 17 00 48 26 11 19 00 54 10 00 L44 15 00 13 54 02 00 13 54 02 00 00 00 12 00 00 00 00 00 17 33 06 00 17 33 06 00 00 01 00 00 09 30 24 00 09 30 24 15 28 16 17 00 02 00 00 D00 02 523 22 00 03 17 14 00 03 17 14 00 03 54 07 00 03 54 07 00 05 33 05 00 06 11 07 00 06 11 08 00 06 11 08 00 0 7 35 25 O0 07 35 235 00 07 35 23 00 07 35 23 00 07 36 20 00 07 36 20 00 08 35 24 00 10 36 03 00 10 36 03 00 02 30 00 00 03 17 14 00 03 17 14 00 03 54 07 00 06 11 07 00 06 35 04 00 06 11 08 00 06 11 08 00 06 14 08 AAA A 00 07 35 23 00 07 35 23 00 07 36 10 00 07 35 23 00 07 36 20 00 07 36 20 00 07 37 20 00 10 36 03 00 10 36 03 00 10 39 09 Page 92 records the material needed by the edit list from original sources such as video tape edits the source audio recorded in the capture process placing it at the destination Navigate to the file locat
56. 05 10 04 19 15 00 13 52 07 621 My Name Is Frank _ Track 85 1 09 50 27 05 10 04 19 15 00 113 52 07 621 My Name Is Frank _ Track 86 1 09 50 27 06 10 04 19 15 00 13 52 07 Closer new 03 Track 1 1 09 51 0 3 09 IERTA EHF OO 00 08 25 Closer new 03 Track 2 1 09 51 03 09 09 51 12 07 00 00 08 lt 3 LHall Frank Open mp3 ne Track 7 1 09 51 03 09 09 51 51 19 00 00 46 10 LHall Frank Open mps ne Track 8 1 09 51 03 09 09 51 51 19 00 00 48 10 CLOSER_12 Track 11 1 09 51 03 09 09 51 03 22 00 00 00 12 CLOSER _12 Track 13 1 09 51 03 09 09 51 03 22 00 00 00 12 Closer new 03 Track 39 1 09 51 053 09 09 51 1 2 07 00 00 00 23 Closer new 03 Track 40 1 09 51 03 09 09 51 12 07 00 00 08 lt 3 LHall Frank Open mp3 ne Track 45 1 09 51 03 09 09 51 51 19 00 00 46 10 LHall Frank Open mips ne Track 46 1 09 51 03 09 09 51 51 19 00 00 48 10 CLOSER_12 Track 49 1 09 51 03 09 09 51 03 22 00 00 00 12 CLOSER _ 12 Track 51 1 09 51 03 09 09 51 03 22 00 00 00 12 1 09 51 03 09 09 51 12 07 00 00 08 23 Closer new 03 4 Track 77 Under Playhead Only Offline Clips Reveal File an Refresh While the Clip Search dialog is open you can e Filter the list by typing a sequence of characters in the text box Only clip names containing that sequence will be displayed e Sort the clips in track order start order end order or duration or clip colour by clicking on the column header Clicking the header a second time reverses the sort order e Double click
57. 1 0 e old E Delete ald Hl de al Right side of display The value grid shows the parameters of the EQ being applied to the clip or range of clips Pyxis G2 Page 89 Operator Reference Manual CHAPTER 10 CLIP EQUALISATION September 15 2011 Band There are four EQ bands that you can apply They are given the names commonly used on mixing consoles but actually they are not in fixed ranges you have the full frequency range available on each of them Filter Type Choices are Band pass filter High pass filter Low pass filter Each band can be set to any filter type Mouse click on the button to cycle amongst the choices Frequency The centre frequency of each band Gain The gain of the band Range 99 to 20dB Q This displays the Q of the band or indicates the type of shelf Range 0 99 Enables Used with the Apply command Only the Enabled bands are applied to the selected clips Value Grid Band Gain Eu an Pas az so os s os The Value Grid shows all the current parameters of the EQ being changed q y V V MV L BBA Applying the Changes To apply your changes click the app1y button Only the bands whose Enable checkboxes are selected will be applied To escape without applying your changes click the cance1 button New or Old Whilst adjusting an EQ parameter it is possible to toggle between the new and old settings by clicking the New 014 radio buttons until you apply the change
58. 15 2011 Chapter 24 System Files Introduction Pyxis G2 uses a number of files to store setup information These are normally set to sensible values at the factory but in some cases you may need to change them Working with Pyxis G2 System Files System files are stored in the C Program Files Fairlight FMC Data directory Use Windows explorer or use the trackball to click on My Computer on the desktop to navigate through the file system Use the Notepad text editor to edit files by double clicking on the file name The I O Config TXT File The I O Config txt file specifies what I O hardware is fitted with your CC 1 engine This file must be edited to allow the Pyxis G2 to properly address the physical I O hardware The I O Config txt file is stored in C Program Files Fairlight F MC Data directory Open the file with the Notepad text editor define the physical I O as described in the file You can also name indi vidual I Os which will then bring their names up on the FAT channel when you patch them System Ports System output ports can only be accessed from the Monitor Setup Patch Outputs menu Using system ports for control room monitors prevents the operator from inadvertently patching signals direct to the power amplifier inputs To define a system port enter an attribute value of 1 as described in the I O Config file The file contents are similar to the following I O configuration There are three types of I O 1 is A
59. 163 Time Scale anna 31 LOVE cccececueuevevevevsvaveveveneneneneneenenes 89 90 TIMCCOC co cccccccccccccecccccceccccccecececcccecece 142 Link Group Format 102 Track Selection civic 30 Locking Automation to Video 162 Transport Controls coooccnnnnnnannnos 33 35 MarKSscocoscccosncnnnnnaronnarennnn eras cnn acercan 118 Tiara 73 MeteringQ setcseerssessssseersseeresseessseerenseenens 54 MCs RARE 162 Momentary Talkback 163 Unpatching Inputs c ccccccsccesesseeeeeeeees 63 PIOMIEOR PONS road 159 Update Oys ELTES netnaariaiods 165 Monitor_SOurces TXT sss 165 US contare 165 Mono CIP ssccessancesnnepetatenstagvaamsetsacrantes 29 NW MOUOM ausissi dunikenn atakas 162 Naming Wave FIGS inicia cc 120 NO ET PE tease feats ose A ee 104 Pyxis G2 Page 166
60. A AOS Boda Dic Probet aiy wks Theme EVO1 This is NOT the subject of this manual L E al LOCA yor AA AAA TART AT LN UU For information about the EVO1 themed version of Pyxis please see the previous Pyxis Manual entitled Pyxis MT User Manual Pyxis G2 Page 9 Operator Reference Manual CHAPTER 1 INTRODUCTION September 15 2011 Chapter 1 Introduction Introduction Pyxis G2 is a new product from Fairlight which combines the audio processing power of CC 1 with a video oriented interface to create an audio video dubber with large track capacity The Pyxis G2 interface is a simple mouse and screen based GUI that makes standalone operation very easy Alternatively the system can be used as a 9 pin slave in a larger system when deployed in a mixing or live production environment About This Manual The Pyxis G2 User Manual provides all the information necessary to rapidly become proficient at operating the system in a professional audio environment This manual is designed to familiarize engineers with the facilities provided by Pyxis G2 The terminology and concepts used in this manual assume a reasonable knowledge of audio and video principles and studio procedures Pyxis G2 Page 10 Operator Reference Manual CHAPTER 2 PYXIS G2 OVERVIEW September 15 2011 Chapter 2 Pyxis G2 Overview Introduction ATPyxis G2 is the latest generation digital audio video system from Fairlight offering
61. Cancel Apply Watermarking allows you to superimpose a graphic design with partial transparency over your video file either on capture or while playing If you capture the file with the watermark it is permanently written into the video file Controls for watermarking are found in Setup gt General Preferences on the Watermark tab This tab is present if a Decklink video card is present and active See your Fairlight distributor for information about video cards Choose the bitmap you wish to superimpose by typing its name in the Bitmap field or by pressing the Browse buton Selecting the movement checkbox causes the watermark bitmap to periodically move on the video output The direction of the movement is specified with the pulldown with choices L gt R R gt L Top gt Bottom Bottom gt Top Selecting the dynamic checkbox causes the watermark bitmap to periodically turn on and off The time for each cycle is specified Pyxis G2 Page 48 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 Using Pyxis Track as a Machine Selecting Pyxis Track as one of your machines allows you to take it offline the same way as physical machines For information about setting Pyxis as a machine see Chapter 22 Machine Control For information about editing with machine control see Chapter 8 Editing Pyxis G2 Page 49 Operator Reference Manual CHAPTER 6 AUDIO RECORDING September 15 2011 Chapter 6 Au
62. DR2 project select the Localize command from the Process Menu above the Editing screen The displayed dialog will ask whether you want to localize all files or just the selected ones Selected Clips only Handles in Seconds Head 1 0 Tail E Handles Localizing only copies those sections of the original recordings that have been actually used in the project Anything that has been edited out will not be present To provide insurance for future editing you can save Handles on each piece of audio These are extra pieces of audio that can be exposed using the Trim menu It s advisable to use handles unless the edit is absolutely final Recovering Lost WAVs If a DR2 project has not been saved recently any recordings made since the last save will not appear in the project next time it is opened These recordings can be recovered and resynced as follows Step 1 Open the DR2 Project Step 2 Open the folder in Windows Explorer that contains this project Open its Media folder Step 3 Identify the WAVs that are missing from the project These will normally be the most recent ones i e the ones with the latest modification date Step 4 Drag the missing WAV files from their folder to the DREAM II track display and drop them there Step 5 For each WAV file that you have dropped select it and notice the track number embedded in its name Place it on that track Step 6 For each WAV file select it by moving the transpo
63. F7 CID_SW_MACKIE_F8 CID_SW_MACKIE_MIDI_TRACKS Pyxis G2 Page 152 Operator Reference Manual CHAPTER 23 HUI SLAVE MODE September 15 2011 CID_SW_MACKIE_INPUTS CID_SW_MACKIE_AUDIO_TRACKS CID_SW_MACKIE_AUDIO_INSTRUMENT CID_SW_MACKIE_AUX CID_SW_MACKIE_BUSSES CID_SW_MACKIE_OUTPUTS CID_SW_MACKIE_USER CID_SW_MACKIE_OPTION CID_SW_MACKIE_SAVE CID_SW_MACKIE_UNDO CID_SW_MACKIE_CANCEL CID_SW_MACKIE_SOLO CID_SW_MACKIE_DROP CID_SW_MACKIE_CYCLE CID_SW_MACKIE_DISPLAY_SMPTE You may add any of these to your remap file and assign them to any Dream II key For help with Dream II key assignment please consult your Fairlight customer support organization Remap to Macros One easy way to get more power from HUI keys is to map them to your macros An example of a mapping line that does this CID_SW_MACKIE_F1 CID_SW_M_1 CID_SW_MACKIE_INPUTS CID_SW_BANK_1 Using macro and bank assignments you can get access to 27 macro keys Identifying Keys On some HUI controllers the key labelling may not match the list above You can find out the name of any HUI key using the following method Step 1 Start the system and load a project can be empty Step 2 Start the MSAT application Start All Programs Fairlight gt FMC FMC Utils gt FMC Step 3 If you see this error message at any time click OK it doesn t mean anything is wrong ES X Version Error FMC and MSAT have incompatible UICtriViewDefs Close MSAT and restart a compatible version
64. G2 s video screen which indicates when an inconsistent timecode frame was encountered Pyxis G2 Page 140 Operator Reference Manual CHAPTER 21 TIMECODE SETUP September 15 2011 How Pyxis G2 Synchronises Pyxis G2 goes through a number of steps in achieving synchronization in play mode 1 Read the position reference and start loading up the corresponding audio on all active tracks 2 When ready start playing but with the outputs muted Use variable speed to reduce the error between the Pyxis G2 position and the Position Reference until it is very small 3 Switch to the Motion Reference for continued playback The system is said to be locked once this switch is made and the audio is unmuted 4 Warn of error status if the sync error increases if a reference signal is lost etc Synchronization Conflicts When you are recording a digital source it must be synchronised to the same Master Clock Reference as Pyxis G2 or an overflow too many samples or underflow too few samples may occur at the input This causes a characteristic periodic form of digital distortion called a whisper A whisper sounds like a brief glassy or metallic buzz and occurs about once every few seconds depending how fast the samples are overflowing or underflowing The best solution to digital sync conflicts is to drive all digital devices from a single studio wide word clock signal Then all devices will have identical word rates so whispers never o
65. G2 Page 59 Operator Reference Manual CHAPTER 7 PATCHING AND ASSIGNMENT September 15 2011 Analog an analog physical input or output Digital an AES EBU physical input or output MADI a MADI physical input or output Osc the system oscillator and noise generator The second part can be In the input of a signal path not a physical input Out the output of a signal path not a physical output Direct each signal can have a Direct Output Send Insert Send from a signal path Return Insert Return to a signal path Talkback the Talkback system shows Comm1 and Comm2 Inputs physical inputs analog or digital Outputs physical outputs analog or digital So for example Analog Inputs means the physical analog input ports while Aux Bus Send means the Insert Sends from the Aux Busses Input Gain and Phase Analog and Digital inputs can have digital gain or attenuation and phase reversal applied at the input Inputs are selected by first selecting the signal paths that they are patched to There are two ways to set input gain and phase You can use the mixer screen or the track keys Patching One Input To Multiple Signal Paths It is possible to patch the same physical input to many different tracks and record any that you wish at the same time Unpatching Inputs To remove input patching from a set of one or more tracks press the Patch 1 0 key select the tracks and click the Remov
66. Note When the ADR is in Record mode double clicking a cue will select it and initiate a recording Cycle Playing Back a cue Step 1 Turn off the Rec Playback button This puts the ADR system in Playback mode Step 2 Select a cue The transport will locate to its In Time Step 3 Click cycie This will cause the transport to drive through the In and Out points once playing back the audio Note When the ADR is in Playback mode double clicking a cue will select it and initiate a playback Cycle Pre Record Pre Record allows you to enter record a little earlier than the time of the cue This is useful when recording artists that tend to anticipate the entrance The streamer will still indicate the cue in time but you are able to capture the audio a little earlier Early In Early In can be clicked during the preroll of a record cycle It causes recording to start immediately Pyxis G2 Page 113 Operator Reference Manual CHAPTER 16 ADR September 15 2011 Rec Out If desired the system can ignore the Out time of the cue and just keep recording until you exit manually using Stop Jog Rewind etc The Rec Out screen button controls this When unselected grey the record Out time will be obeyed When selected yellow manual exit will be used Keep Playing At the end of a cycle you may wish to keep playing in order to hear the next section of track Clicking the Keep Playing button at any time during a cycle will cause the p
67. Playing Edit Cue ADR Characters Your project may contain a list of characters and the cues assigned to different ones Creating characters Step 1 Click in the Character box which normally shows lt Show all gt Character lt 5how all gt Pyxis G2 Page 109 Operator Reference Manual CHAPTER 16 ADR September 15 2011 Step 2 Type the name of a new character Step 3 Click the Add button Filter by character To show only one character s lines use the Character drop down menu to select one character Character Sort by character To sort the list by character click the Character tab at the top of the ADR list box From To Dialogue Character Andrew o0 00 09 25 OO 00 11 14 I hope you don t mind 00 00 10 11 00 00 15 11 sunrise and sunset Peter 00 00 11 15 00 00 13 06 It s always been this way Peter 00 00 13 01 OO 00 15 25 The long and the short John e Enable Beeps i Show Streamer Handle E Fr Prerall 2 sec Postrall fo sec Cue From In the same way you can sort by From time To time or dialog alphabetically Click any one of these a second time to reverse sort Early In PreR coll Rehearse CYCLE STOP To Rec Playback Keep Playing Rec Out ADR Preferences Once you have entered all the cues that you want to use you may set up your preferences by clicking the ADR Menu and selecting ADR Preferences The following screen is displayed Pyxis G2 Page 110 Operator R
68. Smart Pane j Show Pyxis Track j Multi Video Monitor j Playback Wideo Source j Edit Workspace j Marks Sort ideo Locators Tracks j Clip Search Displayed Clip Information Orphaned Media TimeScale Hours Min Sec Frame Background Tasks Hours MinfSec Frame SubFrame Performance Hours MinfSec Frame SubFrame Samples Statistics Feet Frames 35 mm Timecode Display Feet Frames 16 mm Software Keyboard Hours Feet Frames 35 mm Undo History Hours Feet Frames 16 mm Bars and Beats Bar Beat display Positions can be displayed in bars and beats To enable this use the Edit Screen menus and click View gt Timescale Y Bars and Beats The Edit Screen shows dark bar lines and light beat lines To set up parameters go to Setup Bars and Beats Setup This displays a dialog with the following parameters Pyxis G2 Page 30 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 Tempo Time Origin time On 00 00 00 Set 1 1 1 Snap to mE Mumber Bars 1 BPM from Range Tempo Expressed as beats per minute The box on the right allows you to choose the beat value used in specifying the tempo In some cases you may wish to specify beats differently from the time signature Time This is the time signature expressed in the usual way Origin Time This is the timecode where the first bar starts To set it locate to the timecode of the first bar and click
69. Stuffing is complete When dragging and dropping files onto the Dream II timeline you may notice some files are Fuf Stuffed automatically Dream II performs Fuf Stuffing automatically when it is required for QDC compatibility for example if you drag a file larger than 4 GB onto the timeline Dream II users can also copy clips from one MT project to another In doing so the user creates a relationship between Fuf files belonging to one project and Fuf files belonging to another Using Save As with an MT file has the same effect and creates a Parent Child relationship between the original MT Project and the saved version To break any such inter Project dependencies select Pyxis G2 Page 129 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 Process gt Detach from the Dream II menus After detaching your MT Project you can select Process 3 Stuff Fufs All Clips or Process Stuff Fufs Selected Clips to consolidate all audio into Fufs associated with your current project If you are unsure of what file a clip is stored in you can find out by selecting View 3 Clip Search from the Dream II menus You will see the filename associated with each clip in the list and you can click the Reveal File button to display a file in Windows Explorer Note that you can rearrange columns in the clip search window by dragging and dropping column headers You may need to scroll to t
70. TWARE LICENSE This EULA grants you the following license e You may use the SOFTWARE only on the DEVICE e NOT FAULT TOLERANT THE SOFTWARE IS NOT FAULT TOLERANT Fairlight AU HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE AND Fairlight AU S SOFTWARE SUPPLIERS HAVE RELIED UPON Fairlight AU TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE e NO WARRANTIES FOR THE SOFTWARE THE SOFTWARE is provided AS IS and with all faults THE ENTIRE RISK AS TO SATISFACTORY QUALITY PERFORMANCE ACCURACY AND EFFORT INCLUDING LACK OF NEGLIGENCE IS WITH YOU ALSO THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE THOSE WARRANTIES DO NOT ORIGINATE FROM AND ARE NOT BINDING ON Fairlight AU S SOFTWARE SUPPLIERS e Note on Java Support The SOFTWARE may contain support for programs written in Java Java technology is not fault tolerant and is not designed manufactured or intended for use or resale as online control equipment in hazardous environments requiring fail safe performance such as in the operation of nuclear facilities aircraft navigation or communication systems air traffic control direct life support machines or weapons systems in which the failure of Java technology could lead directly to death personal injury or severe physical or environmental damage Sun
71. Y Tape Mode Process Frame Rate Convert Remove SRC Regenerate Profiles Remove Hidden Clips Gate Preview Gate Discard Unused Media Localize Audio Localize Video Tape Mode Normal Record Make Tape Selected Tracks E Tape Mode Make Blank Tape Selected Tracks Using Tape Mode If you punch into record over an existing Tape Mode clip shown yellow its media will be replaced as you record If you continue to record past the end of the clip it will be extended If you punch into record in empty track space or over an Edit Mode clip shown red or blue the system will create a new Tape Mode clip without affecting the Edit Mode clip Pyxis G2 Page 53 Operator Reference Manual CHAPTER 6 AUDIO RECORDING September 15 2011 Creating Tapes If you would like to ensure that only one clip per track is created by recording you can start by making a Tape across the whole length that you are recording This means making a Tape Mode clip on each track Having selected Tape Mode in the previous step Step 1 Use the From and to buttons in the top left corner of the screen to make a range that represents the length of the Tape you want to make Step 2 Arm the tracks where you want to put a Tape Mode clip Now you have two choices Step 3a Use Process Y Make Blank Tape button to make a blank zero waveform Tape Mode clip on each armed track filling the range Step 3b Use Process Y Make Tape button to make a single Tape Mod
72. _RECORD CID_SW_REC CID_SW_MACKIE_ALT CID_SW_BLUE_1 Blue key CID_SW_MACKIE_ENTER CID_SW_ENTER CID_SW_MACKIE_ZOOM CID_SW_ZOOM CID_SW_MACKIE_LEFT CID_SW_RNGE_JUMP_LEFT CID_SW_MACKIE_RIGHT CID_SW_RNGE_JUMP_RIGHT CID_SW_MACKIE_MARKER CID_SW_GAP_FROM CID_SW_MACKIE_NUDGE CID_SW_GAP_TO CID_SW_MACKIE_SCRUB CID_SW_SHUT_JOG turns Jog on CID_JOG_MACKIE_WHEEL CID_JO_JOGGER this assigns the HUI jogger to the Dream II jogger CID_SW_MACKIE_READ CID_SW_EN_FADER_2 enables faders for automation CID _SW_MACKIE_WRITE CID_SW_EN_MUTE_2 enables mutess for automation CID_SW_MACKIE_TOUCH CID_SW_EN_PAN_1 enables pan parameters for automation CID_SW_MACKIE_TRIM CID_SW_EN_EQ GROUP enables EQ parameters for automation CID_SW_MACKIE_LATCH CID_SW_EN_DYN_GROUP enables dynamics parameters for automation CID_SW_MACKIE_GROUP CID_SW_EN_AUX_GROUP enables aux send parameters for automation Examining this line CID_SW_MACKIE_STOP CID_SW_STOP we see that the first part is the HUI stop key and the second part is the Dream II soft key This will cause the HUI stop key to work on Dream II There are some HUI keys not mentioned in this remap file They are listed below CID_SW_MACKIE_BANK_DOWN CID_SW_MACKIE_BANK_UP CID_SW_MACKIE_CHANNEL_DOWN CID_SW_MACKIE_CHANNEL_UP CID_SW_MACKIE_UP CID_SW_MACKIE_DOWN CID_SW_MACKIE_SHIFT CID_SW_MACKIE_CONTROL CID_SW_MACKIE_F1 CID_SW_MACKIE_F2 CID_SW_MACKIE_F3 CID_SW_MACKIE_F4 CID_SW_MACKIE_F5 CID_SW_MACKIE_F6 CID_SW_MACKIE_
73. ack where you drag it unless you use the options below Found at Setup Y General Preferences Options Place Files at Embedded Timecode Place Files on Embedded Track 7 Bri n MF I BWA Mpeg Quicktime Place Files at Embedded Timecode Some audio files carry a timecode with them Checking this option for a particular file type causes it to be placed at that timecode no matter where you drag it with the mouse Place Files on Embedded Track Some audio files carry a track number with them Checking this option for a particular file type causes it to be placed on that track no matter where you drag it with the mouse Sample Rate Conversion Sometimes the files you import are at a different sample rate than the project When this happens Dream II automatically turns on real time sample rate conversion to ensure the audio has the same pitch and duration as the original Clips subject to sample rate conversion are marked with a black sx label The quality of sample rate conversion may be varied using the dialog Setup Y General Preferences General Live Sample Rate Conversion Fast High Quality Pyxis G2 Page 118 Operator Reference Manual CHAPTER 18 IMPORT EXPORT September 15 2011 Fast Puts a small load on the computer system but doesn t sound so good Very useful when there are a lot of clips to be sample rate converted or a lot of plug ins in the project High Quality Sounds good but loads do
74. ad Duration field value and the Fade Tail command applies the Tail Duration field value to all red clips those wholly inside the range on selected tracks Using the Smart Panel While the Fade mode is active the screen displays shapes and controls for creating and editing fades gt Presets E spture s oi 00 00 00 20 ie Length e Shape El a Duration Fade Presets Fade Head Step 1 Select a track and move a clip under the cursor Step 2 Click the Fade button if not already on Step 3 Click the Head button in the screen display it s near the upper right Step 4 Adjust the shape of the Head fade described below Step 5 Click the Apply button The fade described in the shape is applied to the head of the clip Note that the fade duration is set by the cursor position as when using the Tool Bar commands Length and Shape The Length and Shape tickboxes allow you to choose what to apply You can untick the Length tickbox if you only want to apply the shape and vice versa Pyxis G2 Page 73 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Fade Shape Using the mouse and screen method allows you to set the fade shape before applying it The shape includes the following parameters Percentage X Point this controls the percentage of the fade s duration when it reaches the Crossover Point Attenuation X Level controls how loud the fade is compared to the full Level of
75. aeseeseeeeaeseeeeseeaneags 87 CHAPTER 10 CLIP EQUALISATION cccccsseceeceeeceeeeseeeeceesneeeseussenseeesenesesseneees 88 a o A A wena arenes 88 EO GISDIGY seca a o 89 CHAPTER 11 EDL MANAGEMENT c ccscccesceeeceeeeneeeeceseeeeeeseeneeeeeneeeeeeseeeeseneees 92 PAE OG UE GLION sat AA ee ee 92 LoadiNg aE D EPR E O EEE E 50 92 Capture anda CONTO Martina 93 RECONTO Mari ista 95 Ada itional Facilite sorina mar Pandbiaeesteasementatseenees 96 CHAPTER 12 LINK GROUPS nenons i edvtntades delwataresheidiueaNeaiaateneads 97 o cierna sunasuaa A a tiene eedeeannenes 97 CHAPTER 1 32 NAME sorna da did 101 IMtodUciNa dada 101 Naming Tricks a a 101 Naming Clin AE N 101 SAAN e E a TA 101 CHAPTER 14 gt SOLO AND MUTE cias 103 Selected Tracks usina di 103 CHAPTER 15 GO TO cialis 104 MtToOdtcO Nr das 104 Go To TIMECOGE Oca as 104 GO TO CUD Narea ddr 105 TRE Cup Sears 105 G oa b K ERA o nD ee rn oe TRC nT Te Ore en TR Rene ore een eee 106 CHAPTER T6 ADR casan ede a eee 108 LOCU CUON Saks caskwtestavashcsacanoneseemmmn EA eraasars onvesananseequeecausanianiees 108 Me SADRIEISEtesiceeahatiiscciiesaenahemveacelaanarenearecatnnacuanacanee eeaatiasaa ceeaneseneereusteanv nan mseemanan hice 108 ADR Pi Si RCC SS airada 110 TREO ADR DISDIAY ai ia 111 CHAPTER 17 MARKS cria 115 VIGGO LOCALO O erine A A E T 115 Creating a Video Locator Aa 115 Edna Marks iia 115 CHAPTER 18 IMPORT EXPORT oooccocconccocconccnnconcon
76. an still be done When you Ctrl click a clip when no range is present a range will be created which includes all the previously selected clips plus the one just added If the track containing the clip was not selected it becomes selected automatically Mouse Based Ranges The mouse can be used at any time to create a range Simply click an empty space one where there is no clip and drag an area on the Track display and a range will be created At the same time any clips or parts of clips on already selected tracks that are inside the area you dragged will be selected All other clips will be deselected Selecting clips when creating a range with the mouse does not select tracks but selecting clips by directly Ctrl clicking them does select tracks To remove the current range click but don t drag anywhere with the mouse Moving Clips Clips can be dragged horizontally and vertically with the mouse This changes the clip timecode and track respectively When there is no range simply click and drag any single clip to another time or track When there is a range click on any selected red clip and drag it all other red clips will also be dragged along with the one you clicked Summary of Mouse Editing Actions Action Result Click on unused trackspace Removes range Click on a clip Selects the track containing the clip Ctrl Click on a clip If unselected adds it to the selection makes it red Also selects its track
77. ccur and digital interconnections may made with ease In this instance the sync HOUSE option is always used Pull Up and Pull Down The normal sample rates used by the digital audio industry are 32 000 44 056 44 100 48 000 and 96 000 samples per second The normal frame rates are 24 25 29 97 and 30 These last two may cause confusion when used together Pyxis G2 can alter its sample rates far enough to accommodate the small speed change caused by going from 30 to 29 97 frames per second and back again In other words if you slow down the frame rate from 30 to 29 97 Pyxis G2 can slow its internal sample rate to match This is called Pull up or Pull down depending in which direction you are taking the speed When you choose a frame rate you are telling Pyxis G2 what frame rate to expect To put it more accurately you are telling it the frame rate at which the chosen sample rate will be accurately reproduced For example if you tell Pyxis G2 that the NTSC frame rate is 30 in the Setup Menu and the sample rate is 44 100 it will pull down the sample rate to 44 056 if you feed in timecode at 29 97 If however you change the NTSC field to 29 97 Pyxis G2 will play at 44 100 at 29 97 frames per second and will pull up to a sample rate of 44 144 when timecode runs at 30 frames per second It is advisable to choose a sample rate at which you want to make the final transfer of the Project Then record your material at whichever frame rat
78. change without notice Fairlight AU re serves the right to change any part of this document without notice The warranties remedies and disclaimers above are exclusive and take precedence over all others oral or written express or implied to the extent permitted by law in the geographical area of the product s use No employee of Fairlight AU agent distributor or employee of an agent or distributor is authorized to offer any variation from this policy Copyright 2007 Fairlight AU Pty Ltd Unit 3 15 Rodborough Rd Frenchs Forest NSW 2086 AUSTRALIA Telephone 61 2 9975 1777 Fax 61 2 9975 1999 END USER LICENSE AGREEMENT You have acquired a device DEVICE which includes software licensed by Fairlight AU from one or more software licensors Fairlight AU s Software Suppliers Such software products as well as associated media printed materials and online or electronic documentation SOFTWARE are protected by international intellectual property laws and treaties The SOFTWARE is licensed not sold All rights reserved IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT EULA DO NOT USE THE DEVICE OR COPY THE SOFTWARE INSTEAD PROMPTLY CONTACT Fairlight AU FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE S FOR A REFUND ANY USE OF THE SOFTWARE INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA OR RATIFICATION OF ANY PREVIOUS CONSENT GRANT OF SOF
79. clip underneath is faded with exactly the opposite shape to the clip on top If the clip underneath already has its own fade overlapping the time of the upper clip s crossfade then no induced fade occurs In the following illustration clip layering has been turned on using BLUE Track or View gt Display Layering Pyxis G2 Page 75 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Induced crossfade note lower curve No induced fade lower fade overlaps Fade Options Layers On ALL LAYERS ON is not supported in Fade Mode Razor On RAZOR ON is not supported in Fade Mode Soft Edit Every clip has a small fade at the head or tail to make it sound smoother This is called a Soft Edit and you can control its length To do this click the Setup Menu on the Track screen and select General Preferences In the dialog that is displayed click the Playback tab Step 1 Click the Setup Menu on the Track screen Step 2 Select General Preferences Step 3 Click the Playback tab Step 4 Change the value for Soft Edits The current value for Soft edits is shown in the Audio Options group A value of 72 samples is generally useful when the Project sample rate is 48 kHz but you may set this according to your own taste Creating Smooth Level Changes By pasting a copy of a section of a clip onto itself you are able to change the level of the copy to create a level change If the copy is cross faded with the origina
80. d but it is possible drop in or out of record on specific tracks while the system is recording by arming on the fly Metering Input Levels The input levels to the armed tracks are shown as vertical bargraphs at the top of the screen For tracks that are not armed for record meters show the playback levels Pyxis G2 Page 51 Operator Reference Manual CHAPTER 6 AUDIO RECORDING September 15 2011 Recording Step 1 Locate the transport to where you want to start recording then click RECORD You can also punch into Record while playing Step 2 Click stop or pLay to end the recording You can also stop recording on a track by disarming it Recording Types Recording has two types NEW and TAPE New is always non destructive creating new data and clips This is the most common mode Tape Mode recording allows replacement of existing audio data while recording It is described in a later section of this chapter Monitoring Inputs Two input monitoring modes are available Input and Auto They cover different recording ae as shown below CALI To toggle input monitoring between Input and Auto click the Input Auto button These settings support the following example applications e INPUT The track feed always monitors input Use 1nput when the studio monitoring is fed through headphones or when recording from tape and the desire is to punch in cued from source material rather than playback material e auto The trac
81. der C Program Files Fairlight Dream II Undo Each time a project is opened the system starts writing undo files for it starting with a file called UndoFile_00 1 This file name does not contain the project for which it was created because the system is designed only to work with the currently open project file Immediately after reopening any file the UNDO command cannot be issued it only works on edits made in the current sessions If there is an UndoFile_00 1 already in the folder which there almost certainly is it will be replaced with this one This means that undo files from older projects are difficult to identify But if you have wrongly and very recently saved a project and you wish to access a previous version of the edit list take the following steps Step 1 Open the folder C Program Files Fairlight Dream II Undo 2 C Program Files Fairlight Dream IT Unda GO Mame Size Type Date Modified UndoFile_00 2 SKB 2 File 11 03 2008 2 33 P Only these two A UndoF ile 00 1 ke Tile TSE eras PT files are from E UndoFile_00 4 13KB 4 File 11 03 2008 2 31 PM the most recent 3 UndoFile_00 3 13KB 3 File 11 03 2008 2 31 PM project E UndoFile_00 8 15KB 8 File 11 03 2008 1 46 PM Linda Fila on 7 iC LVE 7 Fil 11 02f90ne 1 47 OM bl 4 b Disk Free space 14 1 GB 74 6 ME My Computer Z Step 2 Choose the undo file you want to open Rename this file so that it has an extension dr2 upper or lower case it doesn t
82. dio Recording Introduction Pyxis G2 can record up to 64 simultaneous tracks to disk The following chapter describes how to configure and then record audio into the system Project Set Up The steps for setting up a new project are described in Chapter 3 Projects Sync Setup The current sync setup can be changed at any time by selecting View gt Smart Pane Setup or by pressing the sync Setup button in the Setup Megamode sample Rate Clock Syne Source s z0 Internal Frame Rate 20 97 f d Position Syne Source lu defined lo a o Detected Sample Rate 47999 Bit Depth lis Sample rate Frame Rate Bit Depth Clock Sync Source Project Frame Rate Pull Up Down Undefined y hal Detected Video Rate Undefined The system supports sample rates up to 192 kHz This is set when a project is created and cannot be changed thereafter The value you place here can be changed in the Sync display at any time afterwards It should match the incoming timecode format for correct synchronisation The system supports sample depths of 16 or 24 bits You can change this value at any time affecting subsequent recordings All previously recorded audio is played back at its recorded sample depth Note that 20 bit recording which was supported in earlier Fairlight products is no longer a choice Choose the clock signal to be the master time reference for the system Choices are SX 20 Internal us
83. e button Patching Monitor Outputs Physical outputs can be patched from the Monitor Outputs To do this Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Press the patch 1 0 button in the Edit or Setup megamode The system displays the Patch I O screen Select CR Mon Out as your Source Select Analog Outputs or Digital Outputs if appropriate as your destination Select one or more of your Monitor Elements Left Center Right etc and the same number of physical outputs Click Patch Repeat steps 4 and 5 until you have what you want Pyxis G2 Page 60 Operator Reference Manual CHAPTER 7 PATCHING AND ASSIGNMENT September 15 2011 Step 7 Close the Patch I O page by clicking its Close Box right clicking anywhere inside it or pressing the Escape key on your QWERTY Oscillator Dream II provides an on board digital oscillator for system calibration slate line up tones and path identification The oscillator may be fed to any track Using the Oscillator Step 1 To turn the Oscillator on and off Blah Oscillator Frequency and Level Step 1 Blah Patching the Oscillator The oscillator may be patched to any track This is done on the Patch I O screen Step 1 Press the Patch 1 0 button in the Edit or Setup megamode The system displays the Patch I O screen Step 2 Select Osc as your source category Step 3 Select the OSC button to patch the oscillator or Noise to select the noise generator Step 4 Select one or mo
84. e clip on each armed track copying all the audio that is already in the range on the armed tracks Afterwards you can replace any parts that are not correct by recording over them Both Make Blank Tape and Make Tape run quite fast about 10 seconds for each hour of track time The advantage of using them is that you do not need to record sequentially you can move around anywhere in the Tape and replace the parts you are ready to work on Automatic Drop in Pre determined drop in and drop out points may be activated using a range as follows Step 1 Make a range using the From and to buttons Step 2 Click the Record Range button in the Record Megamode The transport will preroll the IN point punch into record and punch out at the OUT point The Preroll and Postroll times are set in the ADR menu which is accessed via the Tools megamode See Chapter 15 ADR for more advanced recording options Pyxis G2 Page 54 Operator Reference Manual CHAPTER 7 PATCHING AND ASSIGNMENT September 15 2011 Chapter 7 Patching and Assignment Introduction Before any recording editing or mixing can be performed on Pyxis G2 the system must be configured Setting up Your Control Room Monitors If this is the first time your Pyxis G2 has been used you will first need to set up and patch your control room monitors See Monitoring on page 123 for instructions on patching and using your monitors with Pyxis G2 Some Terms Patching Pa
85. e is going to be used during that final transfer The importance of this choice is that you do not want to compromise the quality of your final product by using sample rate conversion at the moment it leaves Pyxis G2 for the last time You should make these choices at the very beginning of the Project and then you may use any other combination that suits your purposes temporarily during the recording and editing process Pyxis G2 Page 141 Operator Reference Manual CHAPTER 22 MACHINE CONTROL September 15 2011 Chapter 22 Machine Control Introduction Pyxis G2 can communicate with industry standard Sony 9 pin serial controlled machines with a timecode reader installed providing control over external video or audio machines directly from the Constellation Constellation XT can control up to three machines M1 M2 and M3 Of these two can be physical VTRs and the third can be Linear Timecode or MIDI Timecode setting up Machines To choose a machine type to be M1 M2 or M3 Step 1 Click the 9 pin Setup button in the Setup megamode Step 2 The following Smart Pane is displayed Type Config Name Enabled Servo Timecode Offset Status Arn En Video Analog Digital Asm Inh Ref Tc Master config PYH A500 P E O e IO 00 00 00 00 Stopped Iv o e e e e 2 2 rs e o e e e o 3 Q iTe Chase config Ys Chase E ee soe 00 00 00 00 Stop une Bo oe ll Chase a E T eo pro 00 00 00 00 TIMEOUT O
86. e level for just part of a clip then use the split command to break it into the right sized pieces then set the appropriate levels To create a ramp between different levels in one clip first copy the section whose level is to be changed using the copy mode then paste it back on top of its source Change its level as desired then use the Fade Menu to create fades at either end of the clip This will cause it to crossfade with the source clip underneath which will be playing at the original level As Pyxis G2 Page 86 Operator Reference Manual CHAPTER 9 CLIP LEVEL September 15 2011 long as you didn t move the transport between copying and pasting phase coherence will be maintained during the level ramp Applying a Waveform Amplitude Change Amplitude is changed for whole tracks not individual clips We refer to a track s amplitude offset meaning the amount by which the amplitude is changed from the actual sound level being played by the clips on a track Multiple tracks may be selected The amplitude offsets of all selected tracks may be set to a fixed amount or may be trimmed increased or decreased from their current values Step 1 Step 2 Step 4 Step 5 Step 6 Pyxis G2 Click the Level button Select the track or tracks whose waveform amplitude you wish to modify Click the Display Set Of Display Trim button Change the level by typing in a value or using the Jogger Wheel Click ox to make the
87. e sends the top clip to the bottom Importing Clips from Other Projects A library project is any other project that you wish to use as a source of clips The clips continue to reference the same media files as they did in their original project To import clips from another project do the following Pyxis G2 Page 77 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Use the command File Open Library Choose a file from the Open dialog and click OK This opens the Library File i e the one from which you will import Move around the Library File and locate the clip s you want to import You can use a range or not and select one or more tracks The targeted clips will be red Click the copy button in the Edit megamode This will copy the targeted clips to the clipboard Use the command File Close Library to return to your project Locate to the position where you want to paste the copied clips and click Paste The clips are pasted If you want more clips from the same project use the command File gt Open Recent Library to see a list of all the libraries you have used in the current session The clips will be sample rate converted on import to match your current project Gating Clips A rough but useful and quick way to remove unwanted silence or near silence from clips is with the Gate Clips function Using the Gate Clips Function First you wil
88. e the Video track selection on and off Pyxis G2 Page 46 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 Double clicking will make it the only selection Click Here Video track is shown selected Using the Edit Tools Editing tools can be used with the video track the same way as they are with audio The copy and cut commands can be used as with audio to put video clips on the clipboard but unlike audio clips they can only be pasted back to the video track NOTE Cross fades between two video clips become dissolves Audio tracks and the video track can be selected and edited simultaneously Editing is described in detail in Chapter 8 Editing with the Mouse Video clips can be dragged left and right but not up and down across tracks Pyxis G2 Page 47 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 Watermarking General Preferences x Uptions Audiobase Playback Video Capture Projecte Scrollers Themes watermark Audio Plugins Watermark Enabled During Capture M Enabled During Play Bitmap E bmpettestpattern_ 0007 bmp Use Alpha Channel Transparency UZ Invert Alpha Channel amp Coordinate jo Y Coordinate ja e Movement Dinamic IL gt R On Time seconds 10 OF Time seconds g Info The watermark bitmap should be no larger than 300 300 pisels It will play but place undue stress on the system OF
89. ease report any errors or omissions to documentation fairlightau com Table of Contents CHAPTER 1 INTRODUCTION cccccceccseeeeceeeceeeeseeneeseeuneceeeeneeaeeusseneeeeseneeaseeesenees 9 INTO CIO Nas 10 ADOUE PINS MAME li A ts 10 CHAPTER 2 PYXIS G2 OVERVIEW cccccccceeeceecenseeeceeseeeeessseeeeseneeneeeseaeseeseneees 11 DV OGUCTO tas dicte 11 O or E aes tucteeanescansachas cata esaees depenaas anueeans veimane rns rar aeaees 11 SUITING TNS Stein 16 SV SECM SIUC OWI eian pasted irc 17 Organising YOUN SC iS 17 IS A A O 17 CHAPTER 34 PROJECTS unir aes iatanestce sanene sauauenuavenentoeceecaceaaseneagaces 18 PPE OG GLIOM aa AA 18 OPENING Proje 0 ero E aameaneraa ue tentaumee seer seeceeesenenate 18 Saving As Other Names or into Other ForMatS coccccccoccccocononocnonenoninnonononcanonononnoroneninnanenenens 22 CHAPTER 4 AUDIO TRACKS 8 TRANSPORT cccccceeeseeeeeeeeeeeeeeeeeeseneceeseneees 23 INTO UCI Nils 23 Displaying Tracks a 23 Video Tata 24 a A A N 24 BL a e aren o ON 27 SEICCLING TACKS io 28 Tim Scale and Display Zooming iio 29 Audio Scroller PCC PC E age eg tas aa aie 31 Transport CON TOS it aa a a a N tee nenan ean aleve enw 33 LO CEICONBUICUIONNS ura ro isa 34 SO a RINGE e ee en enc eer nr ene re ee 35 CHAPTER 5 VIDEO TRACK 37 IO UC Meadas ca as ipinda 37 Creating a PYXIS Track 37 Aiding and Snowing the Video Train 38 Loading Video into Pyxis Tracks tad 39 Cap
90. edia dea t My Recent Documents Deskto p S My Documents y May Computer My Network Places Step 3 FL_ al 4PHS6NYZ4 7 1M way LA FL_ _al 4PHS6NYZ487 1N way A FL_ _al 4PHS6NYZ47 1P way LA FL_ _al 4PHS6NYZ48710 way LA FL_ _al 4PHS6NYZ487 1R way LA FL_ _al 4PHS6NYZ4X7 15 way A FL_ _al 4PHS6NYZ4 7 LT way LA FL_ _al 4PHS6NYZ447 1 way LA FL_ _al 4PHS6NYZ4871Wway A FL_ _al 4PHS6NYZ4271_ wav LA FL_ _al 4PHS6NYZ427 1 wav LA FL_ _al 4PHS6NYZ427 1 wav A FL_ _al 4PHS6NYZ4271Z wav LA FL_ _al 4PHS6NYZ42720 waw LA FL_al 4PHSGNYZSB73D wav File name Files of type the media in the selected clips EF Es FL al 4PHS6NYZSB73F wav A FL_ _al 4PHS6NYZ5B73G way A FL_ _al 4PHS6NVZ5B73H way A FL__al 4PHS6NYZSB73J wavw A FL_ _al 4PHS6NYZ5272B waw LA FL al 4PHSGNYZS272C war A FL_al 4PHSGNYZS272D wav A FL_ _al 4PHS6NYZ5272F way A FL_ _al 4PHS6NYZ52726 way A FL_ _al 4PHS6NYZ5272H way A FL_ _al 4PHS6NYZ5472I wav A FL_ _al 4PHS6NvZ5472K way A FL_ _al 4PHS6N Z5472L wav LA FL al 4PHSGNYZS472M way A FL_ _al 4PHS6NYZ5472N way To replace the media of clips using that media file do the same as above but use the command Process Change Media All Related Clips Undo and Redo FL_ A FL A FL A FL A FL Ay FL A FL A FL Ay FL LA FL A FL Ay FL A FL A FL Ay FL E Cancel Browse to find the media you want and click the Open b
91. eference Manual CHAPTER 16 ADR September 15 2011 The main purpose of this dialog is to control beeps and the streamer The streamer is a pair of vertical lines moving across the Pyxis screen during the Preroll to the cue At the same time as the audible beeps the line extends upwards and downwards briefly The two lines come together at the cue point and a large cross is shown The extensions and cross can be given a different colour to the lines Note the number of beeps and corresponding streamer crosses is controlled in this dialog but the Preroll must be long enough to accommodate them If the Preroll is too short some of the beeps will be omitted See below for instructions on setting the Preroll The text referred to is that shown on the Decklink output from the Pyxis Track The font colour height control and Wrap Text control are used to customise the text display Note this text display is not shown on the Edit Screen Pyxis Window only on the independent monitor fed by your Decklink card if fitted Use the ADR Display described below to show text over the Edit Screen The ADR Display The cat sat on the mat The ADR Display is a band across the screen which displays the ADR text and also gives an indication of the start point for the cue An example of the streamer is shown below The text is shown and the indicators converge on the centre of the screen arriving at precisely the In time of the cue To turn i
92. elect All Viewed Tracks naL T Track 5 Track 6 Track 7 Pyxis G2 Page 37 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 Once created the Video track appears at the top of the Edit Screen 3 ep Ep aS DET E TG GGHOXYKER de oy il FDIC IDA AA o LI L Hiding and Showing the Video Track To hide or show the video track on the Edit Screen use the menu commands View Y Show Pyxis Track Y Show and View Show Pyxis Track Y Hide Video Track Display Offset When using a monitor with an inbuilt display such as an LCD or plasma screen the picture may be one or two frames late at play speed You can adjust for this using the General Preferences dialog To access this click Setup Y General Preferences Y Playback Pyxis G2 Page 38 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 General Preferences x ptions Playback Video Captu Depay Mode Pis Prol Original Size 4 Use Two Monitors if Available l Bumt in Timecode i MBE Transparent I Avid OMF View Both Fields M Small View Display Both Fields Field Field 2 Either I Large View Display Both Fields 7 Field Field 2 Either he Pus Pro PAL NTSC dog 2 Fielde te Field d Field 2 Either Compensate for Blackmagic 2 47 WISE Driver Bug The control allows you to advance playback by one or two frames While in stop or Jog the correct frame is output but in play t
93. eo 162 Patching Monitor Outputs coccococconocoo 128 Bass Management ccsecceeeseeeeeeeeenees 160 Patching Outputs ccoccocccccconconocanioninnonnns 63 BG ACA sedas 162 PNAS Sunset datan dencia 54 BLUE FICS circa 165 Preroll PUNCH asian 162 DOOM eaaa a a 161 PROICC S nora 19 BUS ASSIGM ote dci 126 PUNCH ear 56 CID AO E E o E E 27 Punch Preroll ccccscsecseeseeereeeeereeeeeeees 162 Cross Fades ccececevaveueueusesevevavaveveusenens 78 O E E E E vaeeaadin 93 Cross over Cable cccccssseseeaueesevanseees 168 A er 37 EIA arpa 65 a na 55 Le A re o 75 Seed NAMES cccocccccconconcnnronnonaconcnaninannns 104 FAINIGIAU PO0 0 0O uP o 2 3 4 Setup Variables TXT iooonccioninnionnennannanoss 165 Alda 72 SUI dea 36 ez OO O o 165 IMCD POCO CONE O E E na eed 163 Frame Rate isis ra ica 53 Speaker_Sets TXT oonconnionionionoanoancannnnons 165 Requena 93 SYNC Posee 73 Gal q APPO A A 93 a A yen 165 CO O aceso 107 System Files ccecceeeeeeeeeeeees 38 152 159 GPIO ENA lO arnsssticonetndcccvadeatemeunseiaats 164 System PONTS scassi na 159 qu oe 27 System_VarlableS ocooccconiocioccccnnonincnno 162 VO namS tiara asias 159 Ica AEEA es 27 Importing Wave Files ccscseeeeeeeeees 120 Talkback Time Threshold coccocc 163 INPUT Micra 54 TE FORMA Torrijas 53 I O Config TXT csessccsecveveseveseseressserens 159 TC HOCK WINDOW saoatc esecitos 162 Joystick SNAP ccocococociccnnncnnnnncnnaninnnnnnnos
94. er If the operating system plays the file immediately it will almost certainly play in Pyxis Track Capturing Video The following assumes your system is equipped with a Decklink Video capture card For the purposes of the example we will be operating in Standard Definition mode Pyxis Track allows an incoming video signal to be captured directly onto the timeline This requires correct configuration of both the Decklink card and Dream II Pyxis G2 Page 41 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 Configuration of the Decklink card Configure the required settings for your Decklink card by navigating to START gt Control Panel Decklink YA Blackmagic DeckLink 6 7 1 x Preference settings for your DeckLink HD Extreme 2 settings Processing video Levels Audio Lewels Set output sor amp HDMI amp Y R Y B Y Set input S n ate aE ed E For video and audio capture Use video setup in TSC tf At 7 5 IRE for use in the USA At 0 0 IRE for use in Japan I Remove Field jitter when video is paused Select 4 4 4 on video output F Usea Gb s SDI for Single Link 4 4 4 Set black ref on video output in capture When not playing video send Black To all the video outputs Requires restarting your computer Set reference output timing a Reference input not detected conca ay It is critical that you select the appropriate I
95. es the internal clock of the SX 20 SX 20 Video uses the video input signal coming into the SX 20 SX 20 WCLK uses a WCLK signal coming into the SX 20 The frame rate timecode format can be changed at any time but should be set to the local standard or to match the format of the video material or project currently being worked on Step 1 Press the setup key Step 2 Press the TC FORMAT soft key Step 3 Turn the jogger wheel to select the desired timecode format Select Non Drop or Drop Frame if applicable Pyxis G2 Page 50 Operator Reference Manual CHAPTER 6 AUDIO RECORDING September 15 2011 Step 4 Press Enter Setting Frame Rate using the mouse Step 1 From the View menu select Smart Pane then Sync Setup Step 2 Click in the Frame Rate drop list Step 3 Select the desired frame rate including Non Drop or Drop Frame if applicable Patching Inputs to Track Feeds A track cannot be armed unless it has an audio signal patched to its input Patching is described in detail in Chapter 7 Patching and Assignment Input Gain and Phase This is described in detail in Chapter Blah Patching and Routing See Input Gain and Phase Arming Tracks Arming Tracks with the Mouse A track may be armed by clicking on the disk at the left of the Track Selection Panel Click here to disarm Track 2 Click here to arm Track 4 Arm on the Fly Normally tracks are armed before you put the system into recor
96. exceptional power and speed for recording editing and mixing Configurable with up to 192 disk recorder tracks dual video tracks capable of HD resolution and up 212 physical inputs and outputs Pyxis G2 integrates full recording capability for audio and video with a simple audio editor and basic video editing User Interface Status Bar Level Meters Timecode position Smart Pane Pais G2 1 4063 feta ditare Project lt 17 tox EA x LONA WR Video scroller Track Moveable Selectors play head Clip timeline Zoom Editin T t Undo redo amp ads did Select grab Video Display Pyxis G2 Page 11 Operator Reference Manual CHAPTER 2 PYXIS G2 OVERVIEW September 15 2011 Smart Pane This area contains a number of different displays at different times It may show Meters Clip EQ parameters Fade parameters and so on Each description of editing functions will include details of the Smart Pane display elements To display different Smart Panels use the menu command view Smart Pane and then choose the one you want View Display Layering J Meters Wit Machine Control Show Pyxis Track Metadata Multi Video Monitor Sync Setup Playback Video Source j Edit Workspace i Marks Sort Video Locators Tracks p Clip Search Displayed Clip Information Orphaned Media TimeScale I Background Tasks Performance Statistics Timecode Display Software keyboard Undo History Range Display Cas ioa a a HIRTIE
97. f the track to INPUT will prevent the beeps from being heard Normally monitoring should be set to AUTO This is done as follows Pres Pyxis G2 Page 114 Operator Reference Manual CHAPTER 17 MARKS September 15 2011 Chapter 17 Marks Video Locators Video Locators are created by dragging video frames to the Locator thumbnails in the Dream IT Pyxis track Dream II 0 0a35 Beta Matrix_Video lt 49 tracks gt MFX Project File Video Locator 0 1 00 0 1 16 0 1 00 06 09 0 1 00 08 03 0 1 00 09 1 0 1 00 09 29 METAN SSA os EE ae a a PRETO Video locators are also indicated by yellow pointers on the timescale Creating a Video Locator To create a Video Locator click on a currently vacant locator icon The current video frame is thumbnailed and displayed in the icon Editing Marks To edit marks select View gt Marks from the onscreen menu Pyxis G2 Page 115 Operator Reference Manual Mame Start of show First break Second break Interval End of show Click the appropriate button to set the Mark time rename the Mark or remove it CHAPTER 17 MARKS Index Time 1 00 00 1 02 E 00 00 12 0 3 00 00 13 12 4 00 00 14 02 5 00 00 14 lt 3 Set Time Jump To Rename Remove Remove All Pew Double clicking a Mark also jumps the transport to its timecode Pyxis G2 Page 116 September 15 2011 Operator Refere
98. he transport is stationary Otherwise timecode is generated only in Play Putting Machines Online Machines stay in stop and are ignored by the DREAM system while offline To put a machine online do one of the following Type Te Master m config PRRLASI z EE Chase z config Ps Chase Chase E config e Select the Enable checkbox in the Sync Setup Smart Pane Serva Timecode rset Status ee ee 00 00 00 00 Stopped 00 ME 00 00 00 00 Pea 0 00 00 00 IO TIME SUT 00 p 00 00 00 00 i l In Stop 00 00 00 00 Video Armm Enabled e Click the M1 M2 or M3 button in the Status bar Config Hame Lte Generator Enabled Editing with Machine Control All the transport controls and locating methods operate with a 9 pin remote machine online The following procedure is used to place new recordings or previously used clips to picture Press the M1 key to toggle the 9 pin machine on or off Constellation s transport will locate to the timecode from the 9 pin machine The system defaults to M1 controlling 9 pin Port A Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Placing Sound to Picture With M1 online locate the video at the desired frame Take M1 offline Locate the transport so the cursor lies on the sync point of the clip CUT or copy the clip to the clipboard Place M1 online the transport will relocate to the video at the desired frame Press lt Enter gt to paste the clip It is also possible
99. he advancement is activated You can have a separate setting for your Decklink output and your VGA output since they are likely to feed different monitors Loading Video into Pyxis Track There are two methods for loading video into Pyxis Track In both cases the video track must be visible on screen Importing a Video File Step 1 Make sure that the Pyxis track is displayed If not see above Step 2 Click File Y Import Video File Pyxis G2 Page 39 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 Step 3 The following dialog box is displayed Click here to browse for the file you want to import E IEICE eonan 4150 3 Sonata mi scale The following file types can be imported using this method e Quicktime mov e Avi avi e Windows media format wmv e Mpeg4 files mp4 e Mpeg 1or2 mpg m2v mvf e dv25 dv or dif e Bitmap bmp or Cineon cin sequence of images in sequentially numbered files 1 frame per file e LongGop requires mxf licence option mpeg licence option plus installation of Mainconcept mpeg2 directshow filter and MXFReader2 1 beta or later also any Dream Pyxis native files which are e uncompressed vmu e dv25 dif e mjpeg vmj e lossless Huffman compression vmh Import by Drag and Drop A quick way to import video files is to use Drag and Drop as follows Pyxis G2 Page 40 Operator Reference Manual CHAPTER 5 VIDEO TRACK
100. he audio in the range is moved to the clipboard We see the ghost Step 4 Select another track and or move to another location The ghost moves to the new track Step 5 Click the Paste button to paste the clipboard The clipboard former range is pasted The range persists after the edit Notes about Cut and Paste Tail Works the same way aS Head but cuts the later part of the clip Range and Head When a range is active Clicking the Head key cuts the audio from the start of the range to the cursor This will not work if the cursor is not in the range Range and Tail work similarly together Multiple Clips and Tracks When there is no range the target for editing is all the clips on selected tracks that are touching the cursor It s easy to tell which because they are always red Pyxis G2 Page 66 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 When there is a range the target is all the clips and parts of clips on selected tracks that are inside the range Again the target clips are always red An exception with a range you can use the mouse to deselect a clip To do this hold down the ctr1 key and click with the mouse The clip will turn blue showing that it is no longer selected You can also extend the selection using ct rl mouse click on a clip This will cause the range to expand so that it includes the newly selected clip and it will preserve the existing selection as
101. he clip into two pieces at the cursor position mute clip Silences the clip cleave clip Removes the link between stereo linked clips reverse Creates a reversed version of the audio in the selected clip s and replaces the original with this reversed version Paste Special Instead of pasting the clipboard contents at the cursor position it is possible to paste characteristics of a clip into other clips Step 1 Copy some clips to the clipboard using the Copy menu the mouse or the keyboard shortcut ctrl c Step 2 Select the destination clips for the paste They can be on multiple tracks and may use a range You may select All Layers or only the top layer Step 3 Click and hold the command Edit Y Paste Special The system displays this dialog Paste Special Source Media Erase Delete Gain Erase Head Eq Erase Tail Restore Head Restore Tail Step 4 Now choose which characteristic to paste Notes e The clip whose characteristics are copied is the earliest in timecode on the lowest numbered track copied to the clipboard e The special paste targets every clip that is wholly within the range on selected tracks Pyxis G2 Page 69 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Trim Trimming allows clips to be resized Trim commands are used to set the head and tail of clips to determine how much of the original recording is played by the clip Trimming may shorten a clip or extend a clip if it is
102. he right to view all available clip search columns Always take great care not to delete files associated with your MT Project You may not be able to recover files once they have been deleted DR2 Projects DR2 Dream II projects are a new project format designed specifically for Dream II DR2 files are not backwardly compatible with older Fairlight products although they can be converted to MT projects with FUF files as described above The DR2 file format provides enhanced capabilities compared with the legacy MT file format and all future development will focus on the DR2 file format Recording in DR2 When using the DR2 format new audio recordings are stored as industry standard Broadcast WAV Files Dream IT Broadcast WAV Files are stored in the Media subfolder of the DR2 Project folder The WAV files are created when recording starts and they are refreshed at regular time intervals during recording When this happens all but the last part of the recording is safely on disk This means that audio recordings in DR2 format are quite secure even if the project file is lost or never saved the WAV files are viable stand alone containers for audio media References to them can easily be imported and re synchronised in a new project or in any other project This process is described below as Recovering Lost WAVs lojal Fie Edit wiew Favorites Tools Help ay Back gt gt Bi A Search E Folders EH Address C
103. ht hand list then click List Media in Project to display a new window containing all media in the Media folder of the project Click Delete Project to remove the project from the hard disk You will be prompted to remove all the media in the Media folder Creating New Projects Once Media Devices have been set up on your Dream II system for Audio and Video you are ready to create a New Project To do this Press the Project key on your Dream II controller followed by the New softkey or select File New from the Dream II pulldown menu You will see the following dialog Pyxis G2 Page 137 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 Dream z ll D lPairlight4UlProjectst E rj 29 97 MD Choose a Project Type MT or DR2 By default your project is created in its own subfolder named with the Project Name This is the recommended practice as it helps keep your Dream II system organized If you prefer you can place your projects elsewhere as long as you select a designated Media Device Give your project a name and select the appropriate options You are ready to begin Backup Project to Folder Both MT files and DR2 files can be backed up using File menu Backup Project to Folder option This feature copies the project file and all the associated media files audio and video to the designated folders Backup Project to Folder places all files associated with a projec
104. ike displayed on clips Bit rate Wl Frame Rate Sample Rate IM Video Size Note that Frame Rate Video Size and Codec are only shown on Video clips see Chapter 34 Pyxis Track for details about video Multichannel Clips Multichannel clips are linked for editing operations They are displayed with a link chain icon You can create multichannel clips in two ways e By importing a multi channel Wave or other file e By Recording into a Link Group of tracks Once a clip has been defined as multichannel operations on one channel of the clip eg EQ affect all other channels Multichannel clips can be broken apart using the command Edit SY Cleave Multichannel Clips Selecting Tracks Feeds may be grouped and linked in various formats Selecting the Group Master or a member of a Link Group will select all members of the group See Grouping on page 85 for more details on group behaviour Press a dark onscreen track selection key to add that track to the selection Press a lit onscreen track selection to remove that track from the selection Pyxis G2 Page 28 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 Click and drag your mouse in the onscreen track selection pane to select deselect multiple tracks Click here to select the video track for editing vi Click here to select Track 1 e lai ssl Click here to _ _ AL OLGOGAR A deselect Track 2
105. iles Fairlight FMC Data monitor_matrix txt to re open the original file for editing Use the arrow keys to scroll down the file to the entry you wish to modify Edit the gain value at the end of a line or type a new line to add an element e g Boom When you have finished making changes click File gt Save then File gt Exit to save the file and exit Notepad Click on the DREAM II Start Icon on the desktop to restart FMC and the disk recorder Your modified monitor matrix settings are now active Removing Boom from a Monitor Downmix The following setting sends the boom channel from a 5 1 bus to left and right speakers of a stereo monitor set 5 1 to Stereo SET_NODE 5 1 Stereo Left Left 0 Pyxis G2 Page 158 Operator Reference Manual CHAPTER 24 SYSTEM FILES September 15 2011 SET_NODE 5 1 Stereo Right Right 0 SET_NODE 5 1 Stereo Centre Left 3 SET_NODE 5 1 Stereo Centre Right 3 SET_NODE 5 1 Stereo S left Left 0 SET_NODE 5 1 Stereo S Right Right 0 SET_NODE 5 1 Stereo Boom Left 3 SET_NODE 5 1 Stereo Boom Right 3 Remove the last two lines to eliminate the boom element from the monitors as shown below 5 1 to Stereo FSET_NODE 5 1 Stereo Left Left 0 SET_NODE 5 1 Stereo Right Right 0 SET_NODE 5 1 Stereo Centre Left 3 SET_NODE 5 1 Stereo Centre Right 3 SET_NODE 5 1 Stereo S left Left 0 FSET_NODE 5 1 Stereo S Right Right 0 The System_Variables File The System_Variables file contains user configured setup
106. ion of an EDL file and click the Open button 9 12 9 16 All Audio Track September 15 2011 Operator Reference Manual CHAPTER 11 EDL MANAGEMENT September 15 2011 Capture and Conform Capture and Conform are performed at the same time The audio for each line in the EDL is captured and immediately conformed Before starting we must set some parameters Step 1 Set up Track Mapping Track Mapping EDL Tracks Record Trks Dest Ti 1 8 A 3 9 12 9 16 All Audio Track in in cn En un a nec Tracks A Track mapping chooses the tracks where you will record in your currently open project DREAM II lists each type of edit that it finds in the EDL e g A12 A 3 etc and allows you to choose which audio tracks to record for each type Often it will be the same set of tracks for all edit types Click in the Record Trks column for each type of edit and choose from the drop down list The Rec Tracks drop down list provides a convenient way to quickly fill in the track mapping for a specific number of tracks per EDL track Presets allow you to save a track mapping for reuse Type a name into the field and click Save To load a preset simply select it from the drop down list Step 2 Select Edits to Capture 1 I gt FT ll D A3 B2 O0 00 46 21 14 00 48 3 4 C Ai BL 00 00 00 00 me D 4 D A12 2 S3EP33 00 14 38 12 00 16 55 1 OS A 34 CLOSE 00 47 24 12 00 48 26
107. jects Note If the project is an MT project stuffing the fufs will render all audio to the current project If the project is a DR2 project using the Localise command will place all the audio in a folder inside the project folder Pyxis G2 Page 117 Operator Reference Manual CHAPTER 18 IMPORT EXPORT September 15 2011 Fully Import Media automatically places the audio from the omf in either your FUF or folder inside the folder of the current project Clip Naming Standard derives the names of clips from the omf Master Clip within the omf file Sub Composition OMF s created in AVID often derive clips from either the Master clip and the Sub Composition This option derives the names of clips from the Sub Composition Use this setting to give your clips more logical names if they are coming from an AVID and not displaying logical clip names Offset Entering a timecode offset moves the whole composition forwards on the timeline Entering a track offset moves the whole composition down in the track display Importing Individual Sound Files Sound files of various types can be imported directly into your Dream II project These include the following MP2 MP3 WAV BWAV AAC and more To import one use Windows Explorer or My Computer to locate the file then drag and drop it on to the Dream II Edit Screen The file will be placed at the cursor position or in the range on the tr
108. k feed monitors the input on record and track on playback Use AUTO when the studio monitoring is fed through cans for voice over recording or over dubs Choose auto to allow cueing from the track then switching to the microphone during a record drop in Pyxis G2 Page 52 Operator Reference Manual CHAPTER 6 AUDIO RECORDING September 15 2011 Punch In Punch Out It is possible to enter record while playing back from disk on Pyxis G2 While playing start recording by pressing the recorb button To drop out of Record press the PLAY STOP JOG REW Or FF buttons You can drop in or out on individual tracks whilst recording by pressing the track keys whilst the Arm menu is active Each time you enter Record in New mode you will create a new clip on each armed track These clips are placed over any other clips that they encounter on the same tracks The monitoring switches from recorded material to live as you enter Record exactly as though you were erasing the existing audio By enabling Display Layering in the View Menu you can see the layers of clips on each track A clip can be lifted in the layer order by clicking on it with the mouse and dragging upwards Tape Mode When Tape Mode is selected you can punch in on existing Tape Mode clips and replace the audio media This can save filling up disks with unwanted material and results in a cleaner simpler project with fewer clips To enter Tape Mode use Process Y Tape Mode
109. l a smooth level transition results When using the copy and PASTE functions be sure to be in stop otherwise a slight movement of the jogger wheel may result in phasing during the fades The same technique can be used to fade one clip EQ setting to another within the same piece of audio Pyxis G2 Page 76 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 In the above illustration the top layer plays the same audio as the bottom layer but may have different level or EQ settings During the fade in and fade out the settings will effectively crossfade Editing on Multiple Layers Clips in Pyxis G2 form layers on each track with the most recently pasted or recorded clips sitting on top of the others During playback and record only the top layer is heard or a crossfade between the top and second layers In the above example the sections that are played are indicated in red and orange this is just indicative not part of the user interface The orange sections form a crossfade between the top and second clip in the stack This layered view can be toggled on and off using the command view Display Layering Many editing functions target only the top layer and some target all the layers as explained previously To access a particular clip below the top layer we use the mouse You can lift or lower any clip from layer to layer by clicking and dragging with the mouse In addition the command dit gt Rotat
110. l need to select one or more track s and select the clip s you want to gate either by selecting a range or by parking the playback head over the desired clips You are now ready to perform the Gate Clips function To do this Step 1 Step 2 Step 3 Step 4 Threshold dB 30 2 eS Tail Handle Fr 0 5 PANAS Head Handle Fr 1 3 _u gt gt P Use the menu command Process Gate Preview Your selected clips will now be shaded in grey The grey areas mark the audio that will be retained after the Gate Clips operation is performed Start by moving the Threshold slider slowly to the right Depending on the type of audio contained in the clip areas will begin to be shaded in pink This indicates the areas that will be removed when the Gate Clips function is performed Once you have adjusted the threshold so that the undesired portions of the clip are highlighted in grey adjust the hold time and pre handle time to fine tune the gating process see below Pink indicates where the gate is open e where audio will be retained Pyxis G2 Page 78 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Step 5 NOTE Threshold defines the level above which the gate is open Tail Handle defines how long the Gate remains open after the audio level falls below the threshold value Head Handle defines the time the gate opens before threshold is reached When you are hap
111. le the transport is in play When nudging a Range clips not wholly within the Range are not affected However the Range itself is also nudged so it is possible to keep nudging the Range without resetting the From and To points Snap Editing Snap Editing can be turned on from the Edit Menu You can then choose what you would like clips to snap to when arranging your clips on the timeline This can speed up operation considerably depending on the nature of the project Pyxis G2 Page 71 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Clips Snap to other clips edges Fades P P 9 Marks Sync Points Snap to other fades Snap to markers in your project Snap to sync points in clips Fade Mode The Fade key on the allows fades to be applied non destructively to the heads and tails of clips The fades are performed by the system in real time as the audio is output from the machine Fades can be created on the fly relative to the playhead or they can be created and or modified on multiple clips at once Fades can be applied from the Tool Bar buttons and from the PC screen tal Presets iso Duration 10 0 00 00 20 i Ss i Length e Shape Fade Presets The Editing screen displays fade information in the Smart Pane at the top of the monitor This is used to issue commands as well as illustrate fade shapes curves Using the Tool Bar Fade Head One of the simplest
112. ll Phy had We ye im My i yall Aah ie They effectively provide an extra zoom range to use on tracks of particular interest while the rest of the screen gives more contextual information You can select tracks for scrollers using the Setup item in the menu at Setup Y General Preferences scrollers General Preferences l x Options Audiobase Playback VideoCapture Frojects 3crollers Audio Plugins Tracks that have scrollers Scroller Settings Level Mapping ideo Track 1 Track 2 Track 3 Track 4 Track 5 Track 6 Track 7 Track 6 Track 9 Track 10 W Scrollers as Outline F Scrollers on full sc een video Scroller follows current track You can also toggle scrollers on and off for the first 10 tracks using the QWERTY keyboard e Ctrl 1 toggles the Track 1 scroller e Ctri 2 toggles the Track 2 scroller e Ctri 0 toggles the Track 10 scroller Only two audio scrollers can be displayed at a time Trying to add more with the above method will not work Pyxis G2 Page 32 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 While audio scrollers are displayed you can e Click at any point to locate to that position e Click and drag the scroller to move the transport e Zoom the scroller by floating the mouse above it and turning the mouse wheel Other scroller preferences e Scrollers as outline you can display the sc
113. mber of the first analogue input that it connects to it MUST be connected to 4 consecutive inputs e yis the number of UP4 units installed e Multiple UP4s must use consecutive IP addresses in ascending order e Inputs lt X gt must be counted starting from ZERO 0 FMC ini and Command Line Options26 FMC is launched automatically when you start DREAM II FMC offers a number of additional command line options as listed below These options may be used in a batch file for special applications All start up options can also be set in the FMC initialisation file located at C Program Files Fairlight FMC FMC ini which overides the commandline options If necessary use the Notepad editor to edit the file Click on the start menu and select Programs gt Accessories gt Notepad and open the FMC ini file Note that the DREAM TIStart Setup page will overwrite the FMC ini file Pyxis G2 Page 161 Operator Reference Manual CHAPTER 24 SYSTEM FILES September 15 2011 FMC ini FMC Commandline Options Option Description C Run MSAT on the same machine as FMC ignoring the p setting g Run without graphics h Hi res mode 1600 x 1200 otherwise runs 1280 x 1024 Lo res mode 1024 x 768 m Enable mix automation D lt 4 44 444 gt Specify the IP address for a network connected machine running MSAT for testing S lt gt Specify mixer type where 0 for satellite 1 for station48 2 for Pyxis G2 3 for station24
114. mp TRANSPORT September 15 2011 Click the Bottom button to move the display to the bottom i e ending at the highest track number in the project You choose how many tracks will be in the project when you first create it You can also select the desired track view in the onscreen view Menu like this View Tracks Number of tracks Video Track If your project contains a video track you can toggle its display using the view Menu View Y Show Pyxis Track Y Show Or Hide The Video Track is discussed in detail in Chapter 5 Audio Track Colours Each audio track has a colour that is shown at the left and which can be given to the clips on that track Selected clips are always shown red e those touching the cursor or in a range on selected tracks Tracks show colour tabs Clips normally show the track colour Clips can also be given special colours To select track colours Step 1 Select tracks you want to colour Step 2 Use the menu Tracks Set Track Colour Pyxis G2 Page 24 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 Tracks Add Pyxis Track Delete Pyxis Track Set Audio Track Count Rename Track Set Record Seed Name Add Clip Click to choose a colour for all selected Set Track Colour j tracks Arm Tracks IE Solo Tracks Click to force all clips Mute Tracks on a track to adopt its colour regardless of Safe Tracks what they are
115. multiple times Pyxis G2 Page 58 Operator Reference Manual CHAPTER 7 PATCHING AND ASSIGNMENT September 15 2011 Normally after a patch both sources and destinations are deselected but if Multi is ON the sources remain selected through as many patchings as you like View Buttons y it The View buttons control which names appear on the tiles If you choose View System the names shown are the functional system names like Track 5 Live 3 etc If you choose View User the names will be the ones you have given to these signal paths For signal paths where you have not given a name the system name is used The Info Button Track 1 SAO ALL Track 3 1 Track 1 Input Pressing the Info button allows you to see more detail about specific tiles To do this press Info then click on any tile The system will show a box with information about the source and destination patching associated with that tile What are the Categories Each category name has two parts The first part can be Track a recording track Live a Live Feed which is a full featured channel bringing audio directly to a bus Main the Main mix bus MT Bus a Multi track bus as used in traditional mixing systems Sub Bus a multi Element bus used for extra mixing functions Aux Bus a mono or stereo bus tied to the Auxiliary sends on the channels Mon shows the elements of the Control Room and Studio monitor paths Pyxis
116. n a positional source allows the machines to tell each other where they are The Position Sync Source indicator is green when a valid Position Sync Source reference is detected and red when the Position Sync Source is missing or invalid synchronization Details Pyxis G2 can track the position and motion of external transports such as a video tape recorder timecode striped audio tape or a timecode generator The disk recorder will play in time with the Master Timecode source so that sound and picture coincide Position This is an absolute location reference to a sequence of pictures or audio It is used to determine whether the disk recorder is playing the right part of its Project For video position reference is usually provided by 9 pin Sony protocol from an RS 422 port For audio tapes LTC is normally used though 9 pin is also a possibility Motion The motion of an external machine is a measure of its speed and the disk recorder must move at the same speed to remain in sync This translates into producing the correct number of samples every second which is called the Master Clock rate This can be locked to a Digital Word Clock a video signal an AES EBU signal by the internal crystal a timecode source or a digital audio source which is being recorded If the Position Reference and Motion References are not the same it is possible that they will drift apart over time This will be shown by a warning at the top of Pyxis
117. n Lock checkbox provides the same option when recording MTC Chase When a machine M1 or M2 with this setting is placed on line it means that DREAM II will chase MIDI Time Code entering the MIDI In port on the SX 20 The settings are identical to those for LTC Chase Machine Control Indicators Name Name of the 9 Pin Device Servo LEDs The left Servo LED is green when the 9 Pin device has servo lock The right Servo LED is green when the 9 Pin device has sync lock For correct operation with 9 Pin devices both LEDs should be green Timecode Displays the current timecode position of the external device Status Displays the device status Offset Displays the device offset Asm Indicates the 9 Pin device is in Assembly Edit Mode Inh Indicates the 9 Pin device is in Record Inhibit mode Ref Indicates the 9 Pin device is receiving a valid external sync reference LTC Generator The LTC generator is an independent machine which can be controlled from the Smart Panel or from the work surface Pyxis G2 Page 147 Operator Reference Manual CHAPTER 22 MACHINE CONTROL September 15 2011 The Gen key on the work surface toggles the generator on and off The checkbox on the left also does this Ltc Generator Enabled In Stop 00 00 00 00 a It has its own offset field shown to the right of its name When the In Stop checkbox is ticked a repeated timecode frame is generated when t
118. n the selected clips to their track colour Follow Track Pyxis G2 Page 26 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 The Clip When audio is recorded or imported into Pyxis G2 it is displayed as a clip The clip is a reference to the audio data stored on disk Clips can be cut copied or moved without affecting the original audio data When new clips are recorded or pasted above existing clips the clips become layered one above the other Normally only the top clip is seen and heard during play back DREAM II now allows all layers to be seen simultaneously To do this double press the takes button in the Editor Megamode or select deselect Display Layering in the onscreen View menu This is described in more detail in Chapter 7 Editing The left end of the clip is known as the head The right end is the tail Clips also contain information about the original timecode location of the audio data when recorded and the current timecode location of the displayed clip If a clip shows only a portion of the associated audio data on disk it may be trimmed to show more Clip Display Information You can choose which information is displayed in clips using the command view gt Displayed Clip Information The system displays a dialog like this Pyxis G2 Page 27 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 Select information you would l
119. n the centre of the screen arriving at precisely the In time of the cue To turn on the Streamer click the ADR Menu above the Track display and select ADR Display Pyxis G2 Page 112 Operator Reference Manual CHAPTER 16 ADR September 15 2011 Cycle The Cycle command is used to initiate ADR actions It will execute rehearsal recording and playback depending on the mode of the ADR system See below for details Rehearsing a cue You may rehearse cues before recording them Is this needed in a system where all recording is non destructive Your call Step 1 Click the Rehearse button This puts the ADR system in Rehearse mode Step 2 Select a cue The transport will locate to its In Time Step 3 Click cycie This will cause the transport to drive through the In and Out points once switching the track from repro to input simulating the record experience Click the stop button at any time to stop the take or use the Stop button in the transport controls Note When the ADR is in Rehearse mode double clicking a cue will select it and initiate a rehearsal Cycle Recording a cue Step 1 Click the Rec Playback Step 2 Select a cue The transport will locate to its In Time Step 3 Click cycie This will cause the transport to drive through the In and Out points recording a take then cycle through again for playback Click the stop button at any time to stop the take or use the Stop button in the transport controls
120. n which the audio was first recorded The GUID is a system number discussed below GUIDs Dream II Broadcast WAV Files are named using GUIDs A GUID is a unique ID that makes it easy for the system to locate files in a database Since GUIDs are hard to read Fairlight has created the Fairlight Shell Extension for Windows Explorer The Fairlight Shell extension is installed by default and allows users to view hidden iXML metadata in the Fairlight Broadcast WAV Files The Project Name Clip Name and Frame Rate are embedded in each WAV file by Dream II during recording and can be viewed with the Fairlight Shell Extension Using the Fairlight Windows Explorer Shell Extension 1 Open Windows Explorer 2 Under the View menu select Details 3 Right click a column header eg Name and select More from the popup 4 Scroll down to the bottom of the list and add the desired iXML columns eg Project you wish to view 5 Click Ok Localize Localizing audio means putting the files in the same folder as the Project file Any audio which is referenced out of other folders is copied into the Media folder for the current Project file as new WAV files Once a project is localized it is much easier to move it to another system or back it up because all the media is in one place Pyxis G2 Page 131 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 To localize files in a
121. nalog 2 is AES 3 is MADI First define the number of different types of I O IO CONFIG type inputs outputs where 10 CONEIG 1 16 8 IO CONFIG 2 32 16 IO CONFIG 3 0 0 would configure the system with 16 analog IPs 8 analog outputs 32 digital IPs 16 digital OPs and no MADI These ports are then define one by one using a number Pyxis G2 Page 156 Operator Reference Manual CHAPTER 24 SYSTEM FILES September 15 2011 of statements like these INPUT type index name attibutes OUTPUT type index name attibutes Note that the index counts from 1 and that the name must be less than 12 characters long The attribute can be omitted a value of 1 specifies the port to be a system port This system has 32 analog IPs 32 analog Outputs 32 digital IPs 32 digital OPs and no MADI Digital Inputs 1 amp 2 are named DAT L amp R respectively Analog Outputs 25 amp 26 are named Main Mon L amp R respectively LO CONFIG 1532732 LO CONFI Gap 327 32 IO CONFIG 3 0 0 INPUT 2 1 DAT L INPUT 2 2 DAT R OUTPUT 1 25 Main Mon lL 1 OUTPUT 1 26 Main Mon R 1 The Monitor_Matrix TXT File The monitor matrix file is a text file which contains a complete set of upmix and downmix matrix coefficients These are used when monitoring a larger format bus on a smaller format speaker set or when selecting a larger or smaller monitoring format than the current monitor source bus Monitor Do
122. name Step 2 Use the command Tracks Set Record Seed Name Step 3 The system displays a dialog box Pyxis G2 Page 101 Operator Reference Manual CHAPTER 13 NAME September 15 2011 Step 4 Step 5 Notes D A Enter the seed name you would like use For the selected tracks Gunshot Seed Index 13 Enter the Seed Name you wish to use on the selected track s Enter the Seed Index This is the number that will be used on the next recording made on any of the selected tracks You may set this to any value you like even if it has already been used The system defaults to the Seed Name Recorded Audio on all tracks This results in lots of clips called Recorded Audio N Use only the following characters in names A Z a z 0 9 _ underscore When multiple tracks with the same Seed Name are recorded the results depend on whether the seednames were applied at the same time or separately If they were applied separately the resulting clips follow an independent sequence of numbers on each track This means you can get exactly the same name on different tracks If the names were applied together the resulting clips have a range of numbers increasing by one with each increasing track number So for example if e The Seed Name is Clip e The next number is 5 e Tracks 1 2 and 12 are in record Track 1 will get Clip 5 Track 2 will get Clip 6 Track 12 will get Clip 7 Pyxis G2 Page 102 Operato
123. nce Manual CHAPTER 18 IMPORT EXPORT September 15 2011 Chapter 18 Import Export Introduction Pyxis G2 has a number of features to allow the import and export of audio clips and Projects Importing Files DREAM II can import the following file types Video Files these can be displayed on the Pyxis track Pyxis Projects these are projects created using the program Pyxis OMF Files these are files from other manufacturers ML Files these are files from older Fairlight products AES 31 Files these are files from from other manufacturers AAF Files these are files from other manufacturers MXF Files these are files from other manufacturers Importing Video Files See Chapter 5 Video Track Importing an OMF Step 1 Use the command File gt Import gt OMF Project Step 2 Browse to the location of the omf and select it Press OK Step 3 The following dialog box is displayed Import Media Clip naming Muendo Advanced K Fully Import Media Standard E Remap Stereo Source Clips C Sub Composition Audio Data Mode Offset Timecode 00 00 00 00 EQ Plugins PreRendered Embeded Media All Media is in One File m iF Available Try to Locate External Files Track jo w Original Search Specific Folders for External Media Import Media Preview Media references the audio files from the omf this may cause slowdowns on large pro
124. nge values Pyxis G2 Page 88 Operator Reference Manual CHAPTER 10 CLIP EQUALISATION September 15 2011 Step 6 Repeat steps 4 and 5 as often as needed Step 7 Apply the changes by clicking the Apply button Each equalisation band has three parameters you can change They are centre frequency of the band gain cut or boost at that frequency and Q factor sharpness of the band or whether it is a high or low shelf To change the filter type for a band click the icon indicated below Click to cycle between Hi Pass Lo Pass and Band Pass filter 0 0 10 M type 3149 9 2 12 500 0 0 Lo e 50 0 0 1 0 W Band Freg Gain MA EQ display w o un o ee o o Ww o o un o o KR w A un K o K a alg ni Presets Freq Gain Q a 20 20 H 10000 0 0 1 0 v Te 10 10 MF 3500 0 0 10 V Left side of display When a clip s EQ is being edited the dots change from black to red as shown here They can be moved with the mouse changing frequency and gain values These values are updated in the value grid as you move the mouse You can also hear the changes in the audio if it is playing after a short delay ILI 4 O 50 100 00 S00 IK ek EK 10K E Fl A A a EA Rea rl a cS 20 20 Presets Band Freq Gain 10000 0 0 4296 16 4 5493 12 5 Range Filter Type Frequency Gain Q Factor Enables El i Lo M Qut 1 0 e Copy
125. ngs to each member to set the link group into a surround format as described below under Link Group Format All defaults also applies the mix parameter values of the first member to all the members Parameters modified are fader level pan EQ dynamics aux sends inserts and direct out state Default Pans applies pan settings to each member to set the link group into a surround format as described below under Link Group Format Default pans affects the pan parameter only No Defaults no feed parameters are modified Step 6 You may repeat steps 3 to 5 to make more Link Groups To close the dialog click the Close Box or right click anywhere in the dialog or press the Esc key on your QWERTY Pyxis G2 Page 98 Operator Reference Manual CHAPTER 12 LINK GROUPS September 15 2011 01 06 30 11 AAA A UILIS ESAI wd Double click here to collapse or expand the linked tracks You can collapse the linked tracks down to the width of one track by double clicking any of the linked tracks close to its left side Do the same thing to expand them Link Group Format When a link group is created with default pans selected the number of members determines the format of the link group When a link group is created you have the option of retaining the current pan setting of each member or using default pan settings for the chosen format If default pans are selected each member of the group is panned to one element of the bus
126. nnel clips Deletes unheard clips hidden by layer s of other clips Cuts the selected clips into two at the cursor Allows the level of selected clips to be set Allows the selected clips to be renamed Syncs the selected clips to their record timecode Reverses the audio in the clips Rotate cycles clip layers around when in BLUE Takes mode Positions the Sync point in the clip Can be used for Jumping Controls Range On Off and sets head and tail of range Controls the number of layers affected by edits Turns Razor edit on and off Turns Razor edit on and off Turns Snap Editing On or Off Defines where clips snap to when mouse editing Defines Jump destination points for speedy project navigation Page 84 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Fade Menu Fades can be applied to clips using the Tool Bar buttons or the Smart Pane as described earlier It is also possible to apply fades using the Fades Menu This is located at the top of your Dream IT window and looks like this Auto Fade Fades to the end of the clip closest to the Cursor Fade Head Fades to head of Clip s Fade Tail Fades to tail of Clip s Make Cross Fade Makes a one second overlap by pulling out the head and tail of Pyxis G2 Page 85 Operator Reference Manual CHAPTER 9 CLIP LEVEL September 15 2011 Chapter 9 Clip Level Introduction The Level mode allows clips to be amplified and attenuated by up to 99dB It also allows the
127. nnnnroncnnnconrnnnrnnronncnnronnrnnrnanenaranes 117 giggora Ulea Ce eer er ee eee ere ene ont ee Ret eee 117 IMPoOrtind luisa 117 IMPOrIna VIGO FICS garie a aa nawtuabusians ete a A AAN 117 MPAA ar OME aen OS 117 Importing Individual Sound FICS rnision 118 Sample Rate Conversion cua 118 EXP OM atai E A eves ee ees ee atc 119 CHAPTER 19 MONITORING corsa ada 123 io ake conned iden A A 123 Assigning Tracks to Monitor BUSES viuda ci 123 Seting WD Speaker eS ai 125 CHAPTER 20 PROJECT AND FILE MANAGEMENT cscceeceeseeeeceeeseeeeeeeees 127 INEFOdUCIO aia 127 do e 127 EP FO VCC a a a E A a 128 DRZ Projects ticece dete tree ticles aia o E 130 WavelonTPromles cts 132 Revealing the Project File a a 133 Backups Gaalndmaeencadandacenn paucwes bwaitastntanannaeenGinlateesadeveniaanviaemacienimuamaiennen 133 PUEO Matilda aa eS 133 A een tan tadmea stat ecduehctnese a e aucae nee cone nnenas anton 134 VIGGO FICS vesaseescdiweecscdrtecantoet inet tore tisha va glee cawiwcunls what baannmmmegaenteGhe inasand weonwuadenngianaieananseenaanienes 135 Typical Pyxis G2 Drive Configuration occccococconeccononconeniononcononinnononnononnonenroninnonenroninnenennenens 135 Designating Media Device 135 Contr lling Scanned Folder anria a AN a a 136 Creating NEW PlrO CCUS sisien dio A 137 BackUp Project tO FOIGED oie asii 138 CHAPTER Z1 TIMECODE SETUP coa 139 IMTOdUCcIO Nara 139 Synchronization Indicators 139 Synenronizadon Det S
128. nputs for your system In the example we are intending to capture video from a Digital Betacam VTR via the Decklink Component inputs If you will be consistently using the same physical inputs for all video capture duties you should be able to set and forget this value Configure Dream II Video Capture options With Dream II launched and a Project with Pyxis track open navigate to Setup Y General Preferences gt Video Capture This window configures the Dream II part of the video capture system Pyxis G2 Page 42 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 General Preferences x Projects Scrollers Watermark Audio Plugins Options Audiobase Playback ideo Capture Device Decklink Video Capture Capture Settings Standard Capture Size 20 56 6 bit 25 00 fos Input Source be Record Format 0Y 25 Capture Format MEDIASUBT YPE _UY Y T Frame Offset jo 25 FPS Save Delete cancel toy Capture Size is a default value based on whether Dream II is launched in Standard or High Definition mode and the current project sync settings See view Y Smart Pane Sync If this setting is not the format you are wishing to capture it is recommended you consider exactly what format you wish your project to be and configure it in consequence The Device value tells Dream II which video hardware capture unit will provide the incoming video
129. om monitors to avoid accidentally patching other sources direct to the power amplifier inputs Specific outputs may be defined for use with control room monitors only System output ports are only available for patching in the Monitor Setup Patching page System ports are defined in the I O Config TXT file as described in The I O Config TXT File on page 156 Use system output ports for patching your control room monitors to avoid accidentally patching other sources direct to the power amplifier inputs Pyxis G2 Page 126 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 Chapter 20 Project and File Management Introduction File handling in Pyxis G2 supports legacy formats from previous Dream II products but also introduces powerful new Project and File management capabilities This chapter details the way the system looks after files Project Formats In Pyxis two native project formats are supported The newer format has the extension DR2 It has the strongest feature set and is always used for newly created projects The older format is called MT This was introduced in the DREAM I product series also known as QDC systems and is maintained with full backward compatibility by DREAM II This means you can open MT files add new material to them edit them and resave You can also save DR2 files in the MT format for use on older machines using the Save As command Choosing Fo
130. on causes the transport to jump to the next Mark or Clip boundary to the left You can also use the Left Arrow key on the QWERTY keyboard to jump left Po Jump Right jumps to the next Mark or Clip boundary to the right You can also use the Right Arrow key on the QWERTY keyboard to jump right mo Frame Left moves the transport one frame to the left a Frame Right moves the transport one frame to the right Jump targets are chosen by the command Edit Settings Y Jump To You may check e Marks e Point heads or tails of clips on selected tracks and or e Fade places in clips where a fade out begins on selected tracks Pyxis G2 Page 15 Operator Reference Manual CHAPTER 2 PYXIS G2 OVERVIEW September 15 2011 Track Number Selectors Click on the numbered buttons to control how many tracks are displayed For example click on 8 to see 8 tracks on the screen Note that when the Video Track is switched on it is counted in this number Click the Up Arrow button to move the track display upwards For example if Tracks 5 to 8 are currently displayed clicking Up will cause Tracks 4 to 7 to be displayed Click the Down Arrow button to move the track display downwards Click the Top button to move the display to the top i e starting at the Video Track if Switched on otherwise at Track 1 Click the Bottom button to move the display to the bottom i e ending at the highest track number in the project You
131. on to instantly locate to its timecode Pyxis G2 Page 34 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 NTE f Y 00 00 26 19 00 00 28 22 00 00 40 06 Active gt may E Locators 00 00 51 17 00 00 14 21 00 00 22 20 Empty Locators Jumping Pressing the Jump keys will move the transport instantly to the next clip or Video Locator Using the mouse Right click anywhere in the Timeline to locate there Right click and drag on the Edit Screen to move the transport Left click in the Video Scroller to locate to the start of the clicked frame Right click in the Video Scroller to locate to the place you clicked in the clicked frame selecting a Range WWD ae a AA A AAA 00 01 04 1 3 00 00 31 15 A Range allows a group of clips across one or multiple tracks to be selected Many functions provided by Pyxis G2 require the use of a Range Use the From and To buttons at upper left of the screen to set ranges Range mode may be turned on or off by pressing the Range button Setting a Range With the Mouse The mouse can be used to set a range To do this click in a part of a track where there is no clip then drag the mouse to another timecode and release it The time swept out by the mouse will become the new range To remove a range click where there is no clip and the range will disappear Selecting Clips with the Mouse Clicking on a clip while holding down the Ctrl ke
132. onfirm closure of FMC Start MSAT using Start 3 All Programs Fairlight gt FMC FMC Utils gt MSAT Shortly after starting it if FMC is running you ll see an error message about incompatible file versions which can be ignored x ES Version Error FMC and MSAT have incompatible UICtrlViewDefs Close MSAT and restart a compatible version Now start FMC using Start 3 All Programs Fairlight gt FMC FMC Early in the boot process FMC will report on the MIDI devices When you see it click the red Stop button in the upper left of the MSAT screen to freeze the display It will look something like this Comms is ONLINE GDB 09 42 59 gt Physical Memory Available 705492K GDB 09 42 59 gt Mix Memory allocated 39062K GDB 09 42 59 gt FMC is ONLINE GDB 09 42 59 gt FMC re sync GDB 09 43 00 gt Disabling UI Completed GDB 09 43 00 gt FaderCount 8 GDB 09 43 00 gt Midi IN 0 of 4 name USB Audio Device GDB 09 43 00 gt MIDI in device 0 GDB 09 43 00 gt manufacturer 65535 GDB 09 43 00 gt product 65535 GDB 09 43 00 gt version 1 1 GDB 09 43 00 gt name USB Audio Device GDB 09 43 00 gt Midi IN 1 of 4 name USB Audio Device 2 GDB 09 43 00 gt MIDI in device 1 GDB 09 43 00 gt manufacturer 65535 GDB 09 43 00 gt product 65535 GDB 09 43 00 gt version 1 1 GDB 09 43 00 gt name USB Audio Device 2 GDB 09 43 00 gt Midi IN 2 of 4 name USB Audio Device 3
133. ony master device in response to the 0x61 0x20 Status sense command If Play Only is set the value of this bit is 1 only when Dream is in Play or Record modes If Play and varispeed is set the value of this bit is 1 when Dream is in Play Record or varispeed modes Some equipment e g DspMedia postation requires this parameter to be set to Play only to work correctly Some equipment e g SoundMaster requires this parameter to be set to Play and Varispeed to work correctly LTC Chase When a machine M1 or M2 with this setting is placed on line it means that Pyxis G2 will chase Longitudinal Time Code entering the SMPTE In port on the SX 20 Play Tracking Determines how many incorrect frames the system must see before it jumps to be in sync with the incoming timecode or stops if no timecode is coming in This allows the system to keep playing over timecode that has gaps Pyxis G2 Page 146 Operator Reference Manual CHAPTER 22 MACHINE CONTROL September 15 2011 Record Tracking As with Play Tracking but recording uses a different number This is because recording sometimes needs to be more tolerant Note that if timecode sync is lost during recording then re established the transport will go back into Play but not into Record Run Lock If the Play Run Lock checkbox is ticked the system will continue to play after first achieving lock to timecode no matter what the timecode does The lower Ru
134. ostroll to be ignored and the system will enter normal Play mode after the cue s Out time Importing ADR cue lists from a text file You may import an entire script through the use of the Import button This can import a short script that has been written in a word processor Each line of text in the file is treated as a separate line of ADR cue text Each line of text can optionally have one or more timecode numbers at the start of the line 00 00 00 00 This line has one timecode number or 00 00 00 00 00 00 01 12This line has two timecode numbers The first timecode number becomes the cue in point and the second if present the cue out point Timecodes must contain 4 individual numbers separated by colons 01 00 23 12 OF semicolons if the timecode is drop frame based 01 01 00 02 Here is an example of a text file in the correct syntax with timecode numbers at the start of each line 00 02 19 19 Her eyes shined bright and true 00 04 57 07 00 09 42 18 Do not look now but 23 58 39 03 00 02 58 19 Haven t I seen you before The format described above is the native format used by Pyxis NLV for storing ADR cue lists You can edit the stored ADR cue lists directly in any word processor or text editor as long as you make sure you save the file as a text file Beeps Audible beeps count down to the record in point The beeps are heard on the lowest numbered armed track but only if it is audible For example setting the monitoring o
135. parameters plus automatically generated system variables Only modify the parameters described below The file is located at C Program Files Fairlight FMC Data System_Variables txt To edit the file open it in Windows notepad as described above Setting the Automation Lock Window The timecode lock window specifies the number of consecutive contiguous timecode frames that the automation system must read from the disk recorder before entering automation record This prevents the system from dropping out of wRitTe mode when locking to an external video transport Edit the following line in System_ Variables txt TC LOCK WINDOW 10 Change the number at the end of the line to specify the number of frames This number will also determine the amount of pre roll required prior to performing an automation mix pass Typical values are TC LOCK WINDOW 1 for Vmotion TC LOCK WINDOW 5 for Betacam TC LOCK WINDOW 10 for U matic Setting the Automation Punch Preroll21 The automation punch preroll sets the transport preroll time applied when using punch to enter automation record Edit the following line to specify the preroll time in seconds Pyxis G2 Page 159 Operator Reference Manual CHAPTER 24 SYSTEM FILES September 15 2011 TC_PUNCH_PREROLL 5 Setting Momentary Talkback Time Threshold The Momentary Talkback Time Threshold defines the amount of time the talkback key must be held down to prevent the switch from latching The defaul
136. py with the amount retained versus the amount removed from the graphic representation click the cate button to process your settings All grey areas in the clip will be removed retaining the pink areas As with many other editing functions in Dream II the original audio is not affected by clip gating only the clips that reference it Any audio removed by gating can be recovered using the Restore Head and Restore Tail functions under the Edit menu Replacing Audio Media As mentioned elsewhere in this manual a clip is a reference to a piece of media on disk Editing the clips is non destructive to the media it simply changes the portion of the media being played by the clip Sometimes it is also valuable to change the media played by a clip This can be done in two ways Step 1 Step 2 Replace the media of the selected clips Replace the media of all project clips using a particular piece of media at the moment Select one or more clips by the usual methods You can use All Layers to affect the clips on all layers and you can use a Range to select multiple clips horizontally in this case only clips lying entirely inside the range will be affected Issue the command Process Y Change Media Selected Clips The system displays a dialog where you can browse for a media file Pyxis G2 Page 79 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Choose new media file x Look ir M
137. r Reference Manual CHAPTER 14 SOLO AND MUTE September 15 2011 Chapter 14 Solo and Mute am Bj Ato car u ck am iG Anto Car Track 3 rack 4 LAICO i kipl i mije hi n h Track 7 Click the M and S buttons to mute or solo any track Double click the M or S button to make it the only muted or soloed track Selected Tracks You can solo all the current selected tracks using the command Tracks gt Solo Tracks You can mute all the current selected tracks using the command Tracks Mute Tracks Pyxis G2 Page 103 Operator Reference Manual CHAPTER 15 GO TO September 15 2011 Chapter 15 Go To Introduction The Go To Menu is used to locate to timecode locations or named clips After the transport has located to the target you will be returned to the mode you were in before the Go To command Go To a Timecode location Step 1 Click the Timecode field at the top of the screen PP o u gt e E iE EEE e 7 z Step 2 The system displays the current timecode If desired type over the timecode using the numeric keypad or the QWERTY keyboard Locate to 00 00 00 00 Step 3 Press Enter or click OK to move to the new timecode location Editing Timecode Numbers The following shortcuts can help to speed up Go To operations 1 The left and right arrows on the QWERTY keyboard can be used to move from field to field in the timecode number
138. re Tracks on the right side of the page Step 5 Click the Patch button The Noise Generator The oscillator is closely allied to the noise generator When patching the noise generator to a source in the Patch page start by selecting Osc then choose Noise Ta OSC COMMS 2 Sub Bus Sub Bus Dir Out Main Main Main Analog Digital Send Dir Out Inputs Inputs Level control for the noise generator follows that of the oscillator set in the Utils Menu The setting for white or pink noise is also found here Pyxis G2 Page 61 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Chapter 8 Editing Introduction Pyxis G2 offers simple mouse based editing Edit Modes The main editing actions are performed in five modes that can be selected on the Tool Bar Copy copies the selection to the clipboard Enter pastes it into the tracks Cut cuts the selection to the clipboard Enter pastes it into the tracks Erase erases the selection Trim retracts or extends the heads or tails of clips Fade fades or cross fades the selection Once a mode is selected it remains current until another mode is selected The Cursor Most edits are performed at the Play Head or Cursor This is the vertical line in the center of the Track Display ome im ie iius O II eer be eee a PTS bs OOO memke BDM AH De ee ee eee m e OOO kem EER AM S 01 ee ee m e Cursor Normally the Cursor is stationary and the clips sc
139. rmalize Normalize will examine the level in every clip you have selected find the maximum level of all the clips then show the gain increase needed to bring it up to O dB Then all the clips will be amplified by this amount giving you the loudest best quality signal possible while maintaining correct balance Audio Type Select bit depth and Sample Rate for exported file s Defaults to Project sample rate and bit depth Mixdown Select Entire Project to export the entire project one file per track in Multiple Mono Mode Select Between Range to export all audio in the current range one file per track in Multiple Mono Mode Select Selected Clips to only export selected red clips always one file per clip regardless of selected Channels Check Selected Tracks Only to only export selected tracks Check Align to Video Frame Boundaries to align exported file s with the video frame edges Check Export Empty Tracks to export blank files for empty tracks if Multiple Mono files have been selected Then select the location you want the exported audio to go and hit OK Channels Allows you to select the format of the files being created by export Channels Single Multichannel File all selected tracks Mono files 1 per track Stereo files 1 per track pair Mono Stereo Files automatically choose feat Mix Tracks to a single Mono File 10 04 20 2Mix Tracks to a single Stereo File Aue
140. rmat At the time of creating a project file the system offers the choice of project formats in the New Project dialog MT n Ran Mew Projectl 2 r ke le PEA E Lara There is no way to change project format after creation but you can save a copy of the current project in the other format using the File Save As command Pyxis G2 Page 127 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 Select the new path and name jx Save jr gt Frank D6 e Ep E My Recent Documents Desktop SD My Documents fr May Computer File name Frank 06 PEO O ere O LLL LLL LL LLL LLL LLL LL LLL Dream oe aeaa Noes Save as type Cancel Places E If you save a project into the MT format it will load and play on QDC systems MT Projects The MT Project format is designed for backward compatibility with Fairlight QDC systems running software version 19 2 11 or higher Dream II can also open MT files created on older Fairlight systems dating back to MFX3 systems running rev 15 x software If you are planning to swap projects with QDC systems use the Save As command to produce a copy of your project in MT format Recording Files FUFs When using the MT project format on a Dream II system new audio recordings are stored in FUF files FUF stands for Fairlight Universal Format and a FUF file acts as an audio container wi
141. roll across the tracks The audio you hear is the waveform passing the Cursor hence its name Play Head Moving Cursor Many products show stationary waveforms with a moving cursor To show this in Dream II select Setup gt Locked Playhead from the menu bar When this item is ticked the cursor is stationary but otherwise it moves Pyxis G2 Page 62 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 While the cursor is moveable you can reposition it by right clicking anywhere in the Edit Screen and dragging the mouse right or left audio is not played while you do this When re locking the cursor its current position is held This allows you to place it away from the middle of the screen which can be useful for seeing more of the incoming audio for example Cut and Paste Whole Clip To cut and paste a clip Step 1 Select a track and move the transport so that a clip is under the cursor The clip is red because it is touching the cursor Step 2 Click the cut button on the Tool Bar if not already selected Step 3 Click the ciip button We see the clip s ghost It s a picture of the clipboard ready to be pasted in Step 4 Select another track and or move to another location The ghost shows where the clipboard contents can be pasted Step 5 Click the Paste button to paste the clipboard Pyxis G2 Page 63 Operator Reference Manual CHAPTER 8 EDITING September 15 2011
142. roller The Video Scroller is a line of frames across the bottom of the screen centered at the current frame These frames cover the same width as the audio tracks Pyxis G2 Page 45 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 al i ka E F a i E E The Video Scroller is useful because you can see specific frames and scene changes coming up and use it for easy location To Display the Video scroller click Setup Y General Preferences Y scrollers General Preferences x Options Audiobase Playback Video Capture Projects acrollers Audio Plugins Tracks that hawe scrollers Scroller Settings Wideo Track 1 Track 2 Track 3 Track 4 Track 5 Track 6 Track Y Track 8 Track 9 Track 10 i Scroller az Outline Select the Video checkbox You can also use the keyboard shortcut ctri to toggle the Video Scroller on and off While the Video Scroller is active you can e Right click on any part of any frame to locate the transport to that exact position e Left click on any part of any frame to locate the transport to the start of that frame e Drag the scroller left or right to move the transport Note there is no zoom control on the video scroller Editing the Video Track Selection Selecting the video track can be done with the mouse To do this click on the V symbol at the left of the video track You can also use the keyboard shortcut to toggl
143. roller waveform in solid or outline format e Scrollers on full screen video you can choose to have the scroller display present when full screen video has been chosen This is useful for moving the timeline e Scrollers follows current track the scroller automatically chooses the most recently selected track for display Waveform in Record Audio Scrollers display the incoming waveform during record as well as the playback waveform This can be useful for anticipating the punch out point on a track Waveforms are also shown on the normal track view while recording Note the Video Scroller is described in Chapter 34 Pyxis Track Transport Controls The PLAY STOP FF and Rew controls work in a similar manner to a tape machine You can increase the fast forward and rewind speeds by pressing the respective keys multiple times This accelerates through 8 24 60 150 and 360 times play speed To enter record click the rec key The Space bar on the QWERTY keyboard can also be used to toggle the transport between Play and Stop The lower row of buttons works as follows e Jump Left pressing this button causes the transport to jump to the next Mark or Clip boundary to the left Pyxis G2 Page 33 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 You can also use the Left Arrow key on the QWERTY keyboard to jump left e Jump Right jumps to the next Mark or Clip boundary
144. rt until it is underneath the play head then issue the command Edit Resync to Record Time This will place the clip at the time where it was originally recorded Waveform Profiles Dream II stores waveform profiles for all the media in your projects allowing it to display full screen waveforms at any zoom range The waveform profiles are extracted and stored in the background after any recording or import function or whenever a piece of media does not have a profile After some time the number of profiles can get quite large and use a lot of space on your computer The system automatically deletes profiles if they have not been used for a certain number of days To control how many days use the command Setup General Preferences Projects Pyxis G2 Page 132 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 General Preferences Options Audiobase Playback Video Capture Projects Scrollers Audio Plugins Autosave Load Last Project on Startup D Profiles Delete Profiles after so days The default is set at 90 days but you may change that to any time you like Revealing the Project File To display a Windows Explorer Window containing the currently loaded project use the command File Reveal Project File Backup Files Each time a DR2 file is saved an optional backup of the previous saved version can be made This will only happen if your system is set up
145. s Pyxis G2 Page 90 Operator Reference Manual CHAPTER 10 CLIP EQUALISATION September 15 2011 In or Out Toggle the EQ on and off with the rn out radio buttons You can do this with any red clip touching the cursor on a selected track You do not have to enter the Edit mode Copying an EQ The EQ parameters of a clip can be copied to another clip or Range of clips Step 1 Step 2 Step 3 Step 4 Step 5 Locate the cursor over the source clip Click the Copy button on the screen The enable checkboxes allow you to choose which of the bands are pasted into your target clip s Locate the cursor over the destination clip or define a Range of clips Click the Apply button Parameter Display Current EQ parameters are always shown at the top of the screen when the EQ menu is active helping to see what is active and what values are current A graph helps you to see what is going on 1 There is no limit to the frequency Range for each band so you can have your low frequency higher than your high frequency if you want When you are using a Range it is possible to change one or more bands for the entire Range while leaving other bands as they were So for example the clips might have different settings for LOW EQ but the same setting for HIGH EQ Saving EQ Settings The system allows you to save the current EQ settings and later retrieve and apply them To save an EQ setting do the following Step 1 Step
146. s Record Tracking As with Play Tracking but recording uses a different number This is because recording sometimes needs to be more tolerant Note that if timecode sync is lost during recording then re established the transport will go back into Play but not into Record Run Lock If the Play Run Lock checkbox is ticked the system will continue to play after first achieving lock to timecode no matter what the timecode does The lower Run Lock checkbox provides the same option when recording Locate Method Cue Only Lace Window 00 00 29 23 Tracking Algorithm jog Power 2 5 Tracking Algorithm play chase Power 12 5 As for TC Master but there is an individual choice of tracking algorithm for Play and Jog Pyxis G2 Page 145 Operator Reference Manual CHAPTER 22 MACHINE CONTROL September 15 2011 Remote Slave Mode When a machine M1 or M2 with this setting is placed on line it means that DREAM II emulates a 9 pin machine and will obey commands sent to it It is the master for timecode At the same time its transport controls are active Select 9 pin ID Allows you to choose the type of machine being emulated by Pyxis This allows for slight variations in the 9 pin protocol Status Sense Play Tally Controls an aspect of 9 pin performance This parameter controls the value of bitO 0 Byte 1 in the Sony Protocol command Ox7X 0x20 Status Data sent from Dreamll system to the S
147. s file can be opened and edited to conform to your specific monitoring requirements The file is laid out as a comma delimited table Each downmix entry begins with a description prefixed with a e g Stereo to Mono Each subsequent row describes a node in the matrix and has the following elements SET NODE Command source format e g Stereo destination format e g Mono source element e g Left destination element e g Centre Gain in dB For example here is the entry for Stereo to Mono downmix Stereo to Mono SET_NODE Stereo Mono Left Centre 3 SET_NODE Stereo Mono Right Centre 3 Source elements that are not passed through to the destination do not appear in the downmix entry Follow these steps to edit the monitor_matrix file Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Quit FMC by holding down the shift key and pressing the Pause Break key on the PC keyboard and typing o then y Use the trackball to double click on the start button on the task bar at the bottom left of the mixer screen Use the trackball to select Programs gt Accessories gt Notepad Notepad is a basic text editor application In Notepad select open from the File menu at the top of the screen Navigate to the following file and click open C Program Files Fairlight FMC Data monitor_matrix txt Select File gt Save As and type monitor matrix bak to save a back up copy then File gt Open C Program F
148. s the machine to unlace if it is given a locate command outside the range of this window Unlacing allows the machine to travel faster and reduces head wear Tracking Algorithm Determines how the machine performs when searching for timecode Each machine may perform better with either choice of algorithm Bi Directional Control When switched on allows either the Master or the Slave to instigate transport commands e g Play Stop etc Pyxis G2 Page 144 Operator Reference Manual CHAPTER 22 MACHINE CONTROL September 15 2011 Edit Delay frames Each VTR has a built in delay between receiving the Edit command equivalent to a pre programmed Record command and actually entering the Edit mode If you the Edit Delay to match the machine s behaviour Dream II will issue the Edit command early so that the VTR enters Edit at the right time Confidence Head Switches the video machine s Confidence Head on or off Stop Command Allows the option of keeping the VTR tape on the heads when the machine stops This will allow it to start playing much quicker but it does increase head wear Head Protect Specifies a time after which the tape is removed from the heads automatically to prevent wear Play Tracking Determines how many incorrect frames the system must see before it jumps to be in sync with the incoming timecode or stops if no timecode is coming in This allows the system to keep playing over timecode that has gap
149. sample rate is synchronised to its clock source There are many choices but normally you will use the SX20 as a sync source and lock it to whichever sync signal your studio is running Synchronization Indicators Det Sample Rate Detected Sample Rate indicates the speed at which Pyxis G2 is running This value is determined by the relationship between the External Video Rate the project Frame Rate the Pull Up Down setting and the project Sample Rate Pyxis G2 Page 139 Operator Reference Manual CHAPTER 21 TIMECODE SETUP September 15 2011 Video Detect The Video Clock Detected indicator is green when a valid Video Clock reference is detected and red when Video Clock is missing or invalid Seeking Lock The Seeking Lock indicator is green when seeking lock and red when not in use or locked Sync The Sync indicator is green when a valid Clock Sync Source reference is detected and red when the Clock Sync Source is missing or invalid Progressive Detect SX 20 supports both Progressive and Interlaced clocks If the Progressive Clock Detect indicator is green a Progressive Clock reference has been detected and is being used as the primary sync reference Clock In Range The Clock In Range indicator is green when the Clock reference is in range and red when the clock reference is out of range Position Sync When synchronising with an external machine such as a video machine audio recorder or digital audio workstatio
150. ssociated with working in surround formats and share many of the operational features of surround format buses Link groups can include up to eight members The simplest link group has two members and fulfils the function of a stereo channel Link Group Features Linking feeds in link groups has the following effects 1 Selecting one member selects the entire link group 2 If desired the members of the link group are panned appropriately in the monitoring output Creating a Link Group Step 1 Click the Tracks button in the Edit megamode Step 2 Click the Track Format button The system displays the Link Group dialog Step 3 Click a track to be the first member of the Link Group or it can be last member All Defaults Default Pans Default Feeds No Defaults Unlink and Reassign LINK GROUP The system greys out all tracks except the seven either side of the one chosen Pyxis G2 Page 97 Operator Reference Manual CHAPTER 12 LINK GROUPS September 15 2011 Step 4 Click one of the available tracks to make it the last feed of the group iii etd ial sil iid id iwi ind wii sili cree O RR nal al aad aaa aaa A RARA ARA RA ARA AR ei ial a dih RARA ARDE Unlink and Reassign LINK GROUP Link groups can include a maximum of eight members which must have contiguous number e g 3 to 10 Step 5 Select one of the options in purple at the right of the screen All Defaults applies pan setti
151. sual way Alternatively click a number in the preset pad at the left of the display Pyxis G2 Page 74 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 0 10 20 0 GB Click to load a factory preset Fade Presets To load a custom preset use the custom presets pulldown menu in the Fades display Click to load a custom preset Iration Save Click to type a new name for a custom preset then click Save Shape x 7 a E 5 iT al T i T iT To save a custom preset use the custom presets pulldown menu in the Fades display as shown above Type a name into the field and click save Capturing Shapes To capture a fade means to extract all of its parameters making them available to apply to other clips Step 1 Click the capture button This will cause it to flash Step 2 Click the Clip Head or Tail button to capture the fade length and shape from the current clip The current clip is the one currently touching the play head on the active track Having captured those values you can apply them to any other red clip by clicking the Clip button Untick shape or length if you don t want to apply it Cross Fades If a fade is placed on a clip and there is another clip layered underneath a cross fade between the two will automatically be induced Cross fade parameters can be modified with the soft key menu functions Induced crossfades are complementary that is to say the
152. t Open If there is already a project open the system will ask if you want to save it Step 2 The system displays the appropriate dialog Pyxis G2 Page 21 Operator Reference Manual CHAPTER 3 PROJECTS September 15 2011 Select project file to open Look in Projects de Fe AES Dena OK MT ali_48tk MT My Recent Bud_S6tk MT Documents Cadillac_96tk MT E FolderInfol28 dsm FolderInfo dsm Desktop MATRIX _45tk MT Matrix video MT gt Select o 21 x ci Es My Documents Open er Send To y e reat ccs o Compute 4 Lomputer apy Fo Create Shortcut a Delete My Network Rename Places Video EsT Properties Step 3 Right click on the file you wish to rename The system will display a list of commands Step 4 Select rename from the list of commands The system will highlight the current name of the file allowing you to edit it Press the ENTER key after editing to confirm your new name for the project saving As Other Names or into Other Formats The Save As command allows you to make a new version of the currently open file This may have a different name and or file format than the project you opened Step 1 Select the Save As command from the File Menu Step 2 The system displays the appropriate dialog Step 3 Choose an alternative file format if required The system will allow to save into MT DR2 or MFX3 format Note that DR2 is the
153. t in a single place making it easy to restore them later Many facilities use inexpensive USB drives for backup Restoring files is simply a matter of dragging and dropping files from the backup folder to the appropriate Audio and Video Media Devices Pyxis G2 Page 138 Operator Reference Manual CHAPTER 21 TIMECODE SETUP September 15 2011 Chapter 21 Timecode Setup Introduction The Sync Setup Menu is used to configure the Project s synchronisation setup Step 1 Click the sync Setup button in the Setup megamode Step 2 The following dialog is displayed Sample Rate Det Sample Rate 47999 video Detect Progressive Detect Frame Rate 25 fps Extn video Rate 25 fps Seeking Lock Clock In Range es Bit Depth fis Pull Up Domwn 1 1 nd Sync Position Sync 5 20 Internal Sample Rate This is set when a project is created and cannot be changed thereafter Frame Rate Can be changed at any time Normally it is best to choose the frame rate of the Master video device in your system or of the timecode being chased if any Bit Depth Can be changed at any time All subsequent recordings will have this depth Extn Video Rate This is the rate of the external video reference applied to the SX 20 This must be set properly for correct operation Pull Up Down Allows setting of Pull Up and Pull Down often used in NTSC video setups Detailed explanation below Sync Source The system
154. t on use the toggle ADR ADR Display Pyxis G2 Page 111 Operator Reference Manual CHAPTER 16 ADR September 15 2011 Cycle The Cycle command is used to initiate ADR actions It will execute rehearsal recording and playback depending on the mode of the ADR system See below for details Preroll and Postroll It s usually necessary to set a preroll for recording This allows the recording artist to get ready for the start Postroll is useful for hearing how the new recording fits into the track Set preroll and postroll using the appropriate fields in the ADR List Once you have entered all the cues that you want to use you may set up your preferences using the command ADR ADR Preferences The following screen is displayed TUES Foll Single Multiple cues sing Pause before rolling T seconds Beeps Colours Number of beeps T Streamer white oF before zero Spacing seconds 0 Cross white e ero beep Frequency lo Gain db 0 Duration ims l Cross Beep Frequency lo Gain db Duration fms 1 Text Color black i Autoscale Font Choose Font Wrap text The main purpose of this dialog is to control beeps and the streamer The streamer is a band across the screen which displays the ADR text and also gives an indication of the start point for the cue An example of the streamer is shown below The cat sat on the mat The text is shown and the indicators converge o
155. t that can be displayed on the screen To open the ADR List click the abr button in the Tools menu Pre Rec 00 00 00 00 Preroll 00 00 01 00 Postrall 00 00 01 00 Delete Delete All Import Rehearse Early In PreRoll From Add Cue Prey Cue CYCLE STOF ReciPlayback Keep Playing Rec Out T Edit Cue Mext Cue li gi SUPE When it is first opened the list is empty of cues Adding a Cue Step 0 Optionally create a range covering the cue you want to add This is probably the quickest way to set the In and Out times for your cue If there is no range the cue will be created with the transport position as its In time and 5 seconds duration Step 1 Click Add Cue A dialog appears for writing the text of your cue Pyxis G2 Page 108 Operator Reference Manual CHAPTER 16 ADR September 15 2011 Enter the kext For the ADR Step 2 Enter the text and click ox Step 3 If necessary set the In Point of the cue locate the transport to that point and click From Your current position will be shown in a dialog You may accept this by clicking OK OR Click From type the timecode you want and click OK Step 4 If necessary set the Out Point of the ADR cue in the same way The cue is shown as below Language Show Streamer Countdown Loop Pre Rec 00 00 00 00 Prerall 00 00 01 00 Postrall 00 00 04 00 Delete All Rehearse CYCLE STOP 3 ate ReciPlayback Keep
156. t value is 500 milliseconds Edit the following line in System Variables txt Change the numerical value at the end of the line to specify the time threshold in milliseconds MOMENTARY TB TIME THRESHOLD 500 Enabling AFL and PFL Modes AFL and PFL solo modes require two of the available buses Disable AFL and PFL to free these buses Edit the following line in System Variables txt Change the numerical value at the end of the line to 1 for enabled or 0 to disable AFL PFL ENABLED 1 Joystick Snap The joystick snap setting defines the minimum distance in pixels between the joystick bracket and the pan target in the channel display required to capture the current pan position with the joystick To alter the value edit the following line JOYSTICK SNAP 2 Metering Numeric Peak Level The numeric peak levels displayed on the mixer display bus meters have a variable threshold The level at which these values are displayed can be set in the System_Variables txt file Edit the following line in the file PEAK DISPLAY LIMIT 950 The value is from 0 to 1000 in 0 1dB steps where 1000 full scale level In the example above the value of 950 will cause the numeric display to first be shown when the signal level reaches 5dB below full scale 970 will set the threshold to 3dB 990 will set the threshold to 1dB and so on Overload Display Time Signal levels exceeding OdBFS on the main meters are indicated by a overload hold display
157. tained in the chapters that follow Status Bar This line shows a number of items of information as detailed in sections below The Zoom level determines how much time is shown on the screen To change it hover over the tracks and turn your mouse wheel The Top Layers All Layers setting controls how editing works See Chapter 8 Editing for details 00 00 22 20 Pyxis G2 Page 13 Operator Reference Manual CHAPTER 2 PYXIS G2 OVERVIEW September 15 2011 The Sync source controlling the system sample clock is shown at left In this case it is the SX20 Fairlight s sync and I O box running on its internal crystal The Timecode shown is the current position of the transport Click on it with the mouse to open a Locate dialog where you can enter any timecode and go there To the right of the timecode display are two lights which change colour as follows Sync shows green if the system has a viable sync signal otherwise red Position shows green if the system sees a viable position signal such as timecode or 9 pin otherwise red The frame rate of the video and audio is shown next in this case 25 frames per second To change this select Sync Setup in the Setup Megamode Also see Chapter 21 Timecode Setup The Video type shown here is SD Standard Definition If you load a video file containing HD content or capture one yourself this indicator will read HD Your system can only capture and play HD
158. tching means connecting signal paths the output of one to the input of another It is accomplished using the Patch I O screen which is accessed from the Patch 1 0 button in the Record and Setup megamodes Assignment Assignment means sending signals to Monitor Buses where they can be heard This is accomplished in the Assign screen which is accessed from the Monitor Assign button in the Setup megamode Using the Patch I O Screen The following basic steps are used to patch any signal to any other Step 1 Press the Patch 1 0 button in the Edit Toolbox The system displays the Patch I O screen Step 2 Select a Source see below Step 3 Select a destination see below Pyxis G2 Page 55 Operator Reference Manual CHAPTER 7 PATCHING AND ASSIGNMENT September 15 2011 Step 4 Click the Patch button on the screen The Patch I O Screen All patching operations can be carried out on the Patch I O screen which is used to represent the physical inputs outputs and signal paths being patched together This is automatically shown when the Patch I O button is pressed You can force its display by holding down SHIFT and ctrl then typing P Sources are shown on the left of the screen while destinations are shown at the right Multi Track 1 1 E a quo tes pens oceans susan scene sono seem peca aa pura sa po pos Command sena oem sne seamos sumas suona Buttons yates satan satan pu nase praca
159. th many individual audio files bundled inside it FUFs are saved as soon as the recording is complete At this point the audio media is written to disk but it is still not safe The clip s that appear in the edit screen immediately after recording are the ONLY reference to the recorded material They are stored in the Project MT file and until that file is saved the audio is not secure FUFs can only grow to a maximum 4GB to maintain QDC compatibility and new FUF files are generated automatically as required FUFs are automatically named based on their parent project So a project named MyProject MT might have FUF files named MyProject_001 FUF MyProject_002 FUF MyProject_003 FUF and so on FUF files are automatically created in the same subfolder as the MT project You must not delete FUF files unless you wish to remove audio from your project Pyxis G2 Page 128 Operator Reference Manual CHAPTER 20 PROJECT AND FILE MANAGEMENT September 15 2011 When copying MT projects to a compliant QDC engine you must always be sure to copy all associated FUF files Otherwise the QDC will not be able to find all of the audio data used in the MT project iol x File Edit View Favorites Tools Help ae Back 3 DI _ Search E Folders 55 Address DiiPairlightaDlProjects Test 1 a gt gt ao Date Modified Pest Li 36 564 KB MT File 11 03 2008 1 39 PM El Test 1 O001 FUF 4 990 KB FUF File 11 03 2008 1 39 PM
160. the button labeled Set 1 1 1 You may move the transport earlier than the first bar which is negative bar territory Note there is no zero bar the number goes from 1 straight to 1 Snap Snap editing is used when dragging clips with the mouse You may set the snap points to any musical interval in the bar To switch snapping on click Edit gt Snap Editing Note that several types of snap may operate at the same time e g clip and beat This can lead to conflicts if two snap points are in close proximity BPM from Range The system will calculate accurate tempos based on fitting to a range To do this mark the In and Out points of the range using the From and To keys Now enter the number of bars that should fit in the range and click the button labelled BPM from Range Audio Scrollers Audio Scrollers give you a close up waveform view of one or two tracks that can be useful for editing or mixing Pyxis G2 Page 31 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 m el e dia tn QO GOCE Ry Ory E ra i CN e a BCGEE O od 7 a if a a amt eT wi MN pa l uy yur NN aM e Ps opa SN he al l iias ee mn YA a i E r y att ani Na a AAA papis al pga ia ii hy T atl A ay bali aa yaaa ale Oe ee oie T T tla ath naa ph ii TA iT LA ro ha kiani LPA i hele lal i fps 2 i Yh my A ig H j 1 a i 1 i k 4 I i pa ean hy Af vd ir A 4 ee Lan jh a oben i ha
161. the clip at the Crossover point Duration the total length of the fade in frames Duration is not really part of the shape but its control is close by Example Percentage 30 Attenuation 3 dB Duration 20 This means that the fade will last for 20 frames The crossover point will be 6 frames into the fade at which time the level will be 3 dB compared with full Level NOTE The fade shape can be changed directly with the mouse by dragging on the red buttons in the graphs Fade Tail Same as Fade Head but the fade is applied to the end of the clip Fade Clip If both Head and Tail are selected when you click Apply both ends of the clip can be faded at the same time Using a Range If a range is present when the Apply key is clicked all clips that are wholly inside the range will be affected by it Fade Presets The system provides nine convenient fade shapes as presets These can be recalled instantly by clicking on the keypad at the left Having recalled a preset it can be applied to the Head and or Tail of the currently selected clips using the Apply button Presets A preset is a saved shape for head and tail Factory presets are provided for your use Custom presets are saved by you To load a factory preset press the Preset soft key then press keys 1 9 on the numeric keypad to choose one of the 9 factory fade presets The preset is loaded into the Shape graphs and can be applied to clips in the u
162. to save it This must be done for your recent changes to be saved Deleting Projects A project can be deleted using Windows Explorer like any other file It is also possible to delete a file in the Open or Save dialogs as follows Step 1 Use File Y Open If there is already a project open the system will ask if you want to save it The system will prompt you to save the current project if it has changed You may respond either way since you are not actually going to close the project Step 2 The system displays the appropriate dialog Pyxis G2 Page 20 Operator Reference Manual CHAPTER 3 PROJECTS September 15 2011 Select project file to open Look in Projects de AES Demo Ok MT 5 ali_48tk MT My Recent Bud_96tk MT Documents Cadillac_96tk MT E FolderInfo128 dsm FolderInfo dsm Desktop MATRIX 48tk MT Matrix _video MT ci Es Select My Documents Open Send To ut Copy oa Fo Create Shortcut s Delete My Network Rename Places Video EsT Properties Step 3 Right click on the file you wish to delete The system will display a list of commands Step 4 Select delete from the list of commands The system will ask you to confirm that you wish to delete the file Renaming Projects A project can be renamed using Windows Explorer like any other file It is also possible to rename a file in the Open or Save dialogs as follows Step 1 Use File g
163. to the right You can also use the Right Arrow key on the QWERTY keyboard to jump right e Zoom click on this button and drag upwards or downward to zoom the Track display in or out e Frame Left moves the transport one frame to the left e Frame Right moves the transport one frame to the right Jump targets are chosen by the command Edit Settings Jump To You may check e Marks e Point heads or tails of clips on selected tracks and or e Fade places in clips where a fade out begins on selected tracks Jump overrides Jumps can be given temporary targets by holding down modifier keys This is only true when jumps use the left and right arrow keys on the QWERTY keyboard Ctrl Jump jumps to marks only Shift Jump jumps to points only heads and tails Mouse Dragging The mouse can be used to move the transport Simply right click anywhere in the Track Display and drag horizontally to move the transport Audio is not heard while this takes place You may also move the transport by clicking and dragging in any of the scrollers Locator functions Rapid navigation through the project is achieved using the following methods Locate to Timecode Click the timecode field near the top of the screen Type a Timecode Click ox Create Video Locators Stop the transport at a frame whose location you would like to store Click an empty Locator button at the right of the video screen Click an active Locator butt
164. turing VIGGO as 41 THE PY XIS WIAdO Wisin diia Error Bookmark not defined Editing the VIGGO Traidores 46 Wat aaa 48 Using PYXIS Track asa Machi a 49 CHAPTER 6 AUDIO RECORDING isc 50 o A O 50 PrO A O E 50 SYNC A A Wee beles dancer a EA 50 Patching INDUS to Track Feeds iia rt i 51 ANNM IICK cta a 51 O pa qe APP o asiune came cage Ganee aca espuanatrmaneuna ec aeeans 52 CHAPTER 7 PATCHING AND ASSIGNMENT ccccceeeeeeeeeeeeeeeeeeeeeeeeeseaaeeeeeeaaeees 95 IMTOdUCIO Mata 55 SOME TENN Serisi a a len id eie ee a a aa 55 Using tne Paten VO SEEN aranna aa a aA a 55 PatchINOMONROOUMDULS ini a E ee Bh ae 60 Oscar ia 61 CHAPTER 8 EDI TUNG cinc 62 1H gid go U evel a y HEAR O ES a ee Rn ee er ern etn nen ene eT 62 TG CUES Osa aia 62 CUCAN P AS Ge tonada 63 CODY Samer ener ree O 69 EV ASC PRE Poe A 69 EXTA Edt 80 0904 E 8 6 po COPPER PE tea aweeiauesaneyean AA enon sanaaumecnuneanene 69 Paste Specials ah eet aioe 69 IAA a es PEO E OE 70 NOT dae 71 MaD EGUN G a 71 Fado MOO aonn A A 72 Eding Om Multiple Le Sida 77 importing Cips fromOther Projects riada 77 Gang CIDE iren a E T A E 78 Replacing AUGIO Medida 79 Undo ana REGO adi 80 Direct Mouse Based Edison 81 Fade MENU Sixeusxwnecvscuawedeacungecasssacieseveusacsnusavastaa A 85 CHAPTER 9 CLIP EEVEL csi dad 86 FOU O aaan N aa 86 Range A a a A a eae elias alae aa a 86 Applying a Waveform Amplitude Change ccccccscsscseceeseeeeeeaeeeeeeeeeaeseeeeeee
165. ugin builder DR2 NjA SoftwareException DR2 Dream II 10 New Project9 MT MT Project N A D FairlightAUlMedia D FairlightAU Projects D FairlightAU Projects New Project2 D FairlightAU Projects New Project2 Media D FairlightAU ML3_AVT40a50 ML4_audio D FairlightAUiMedialvideolmportedAudioMedia ChannelTest48 D FairlightAU Projects New Project9 Media Floyd 96kHz D FairlightAUlProjects Media Frank 06 D FairlightAUlProjectsiBusTest Frank MixO1 D FairlightAU Projects BusTest Media Frank MixD4 very large MT MT MT Project N A D Fairlightau Projects BusTest Frank MixOS D Fairlightau Projects BusTest Media Hubble Briefcase D FairlightAUProjects PluginPhaseTest48 Media iba i D FairlightAU Projects PluginPhaseTest48 ara Mb Caieliahe ALI Meniaeb t Oh ain Ma Ta kAago Media Mixer template iis gt Stop Scanning Reveal Folder List Media in List Media in Project Delete Delete Project View Backup Projects While this pane is open click on one of the devices shown above and its folders will be displayed Now you can select folders and click Stop scanning selected folders Clicking Reveal folder will open a Windows Explorer window showing the selected folder and its contents Double clicking a folder in the list of Scanned Folders will display its subfolders if any in the Subfolders window and the projects if any contained inside it in the Projects window Select a project in the rig
166. uri 140 CHAPTER 22 MACHINE CONTROL 0cccsccceeceeeseeeenseeeceseeneeneeeseeneeesseaeenesessneess 142 INTOdUCIO Nara las 142 Send Up Nace sc ss 142 Machine Control Indicators erarnan N ee ea ss Cala tata reared 147 LTC GEN ridad 147 PULLING Machines ORINA ass 148 Eating With Machine Controla is 148 CHAPTER 23 HUI SLAVE MODE ainiinias an cadedcadbinthaaiicwansdcdaneusandawentaaricrecinesiaeoan 149 IMTOO CUON rreran E EA 149 SU Dr a a 149 MIDI DEVICES iria a a aaa iia 149 Sa A A OA NA o0uuaseek a eas eeuaod Suk eounsteteons 152 Advanced using Scripted Macros iii is 155 CHAPTER 24 SYSTEM FILES ocu 156 TOJU OM cerminan A a 156 Working with Pyxis G2 System Files eesssessessssenneonnesnnosrneonnesnuaennssanosnosannennsonnesnnoennoonnesnneen 156 Remote Mic aMDS untar 161 CHAPTER 25 SPECIFICATIONS ici 163 Audio 1 0 CONQUE Mirra laa a 163 Pyxis G2 Wiring and Connection Details ococcoconociccononeccicnonenoncnnanenoncanonononnanenennanenoninnanons 163 Operator Reference Manual READING THE RIGHT MANUAL September 15 2011 Reading the Right Manual Pyxis G2 has two Themes To choose your theme start the Pyxis software then select Setup General Preferences Themes and use the pull down menu Only one of the themes is described in this manual as G2 va 50S Bota kre Propet lt 17 hae Theme Pyxis NLV This is the subject of this manual FL AMALIA PSOE L FL al Stunner H a Ee EnS da 6 v
167. us Press the deassign all soft key to deassign all sources Press the Bus Assign key to return to the previous mode or select any other mode Monitor Control You can choose between the three monitor buses for listening in Pyxis G2 To choose amongst these sources Step 1 Click the Monitor Control button in the Setup megamode While the Monitor Control dialog is open you may Choose one of the three sources at the left Click the Mute button to toggle the monitoring on and off The monitor system is always muted immediately after a project is loaded Choose between your Main and Alt speaker sets Control the volume by clicking on the rotary knob and dragging the mouse in a circle around it Monitor Speaker Sets Pyxis G2 supports two sets of speakers called MAIN and ALT Each of these can be set up with its own surround format and physical outputs from the system to its amplifiers One set of monitors can be switched on at a time Where the current source surround format is different from the current speaker set surround format the Monitor Matrix provides the necessary fold up and fold down To choose a speaker set Pyxis G2 Page 124 Operator Reference Manual CHAPTER 19 MONITORING September 15 2011 Step 1 Click the Monitor Control button in the Setup megamode Step 2 Click on Main or Alt to choose that speaker set setting Up Speaker Sets To set the format and select the physical outputs for the Main
168. used concurrently To place a machine online select the Enable checkbox in the Sync Setup Smart Pane or click the M1 M2 or M3 button in the Status bar Enter an Offset if desired Use the red Video Analog and Digital LEDs to arm tracks on your remote devide as required Note The master Video Arm Enabled box must be checked and each video Arm En box must also be checked on the desired device before the Video arm LED can be used to arm the video track Click the Eject button to eject tape from the desired device Note that controls will only appear if they are relevant to the selected device type Config Click the Config button to set transport ballistics for the different machine types When a machine M1 or M2 with this setting is placed on line it means that DREAM II will control the transport of a 9 pin machine but will chase the position of that machine in all transport modes In this case the Config Window looks like this Pyxis G2 Page 143 Operator Reference Manual CHAPTER 22 MACHINE CONTROL September 15 2011 Oww AS00 P 0000 30 00 Tracring A EPE EET Se D Standard amp tracks On 10 minutes Locate Method Select between Cue Only operates only in Cue mode or Unlace unlaces a tape machine and puts it in Fast Forward or Rewind when the locate distance more than the number in the Lace Window This allows for faster locates for video tape recorders Lace Window Cause
169. utton The system replaces If en edit function has been performed that you are not happy with clicking the Undo button or using the command Edit gt Undo will revert the project to its state before the undesired edit Afterwards Redo will reinstate the edit Undo List In the Edit Menu there is an undo list showing all undoable functions which you have performed in your current session You can choose one of these operations to undo but be warned it will also undo all operations you have performed s nce the operation you chose to undo to Undo Follow By default when you undo an edit the system returns to the position and view from which the edit was performed This can make it easier for you to correct that particular edit If you don t want the system to follow you can turn it off as follows Step 1 Use the command Setup gt General Preferences Step 2 Click the Project tab Step 3 At the bottom of the dialog check the Playhead Follows Undo and or Zoom follows Undo controls Pyxis G2 Page 80 Operator Reference Manual CHAPTER 8 EDITING September 15 2011 Direct Mouse Based Editing The mouse can be used to select clips make ranges and move clips in time and across tracks This can be done irrespective of which editing or mixing mode is selected Selecting Clips As explained previously the mouse can be used to select and deselect individual clips within the range by Ctrl clicking on them If no range is present this c
170. wn the CPU If you need good quality and have lots of clips to sample rate convert you can localise the media which performs the best quality sample rate conversion and re references the clip Step 1 Select the clips that need to be sample rate converted Step 2 Issue the command Process Y Localise Audio Use handles if the clip has been edited and might need to be re extended Select all clips using this media before localising and the system will only produce a single piece of media which they can all reference Export Exporting Audio You can export audio from a Project in the following formats e WAV e Broadcast WAV o Aif e AES 31 This consolidates your project into a file used by other manufacturers Step 1 Select the clip or clips to be exported Ranges of clips can also be selected Step 2 Use the command File Export gt Audio Tracks Clips Step 3 The following dialog box appears Ce Fairlight Al Projects Media E O FairlightaUProjects Medial lt track name gt way Mono Files 1 per track Sener Slims py AE ernie Normalize Cancel Make your selections and click OK Pyxis G2 Page 119 Operator Reference Manual CHAPTER 18 IMPORT EXPORT September 15 2011 File Type Select Wav BWave or AIF files BWave files will be exported with the timecode stamp from the Dream II timeline Export Using Select Clip EQ and or Clip Level to render Clip EQ and or Clip Level into the exported file s No
171. wnmix Matrix Defaults The monitoring downmix matrix allows any source format to be monitored on any format speaker system The elements of the source signal path are distributed or summed and attenuated as necessary to maintain the soundfield image in the target format When monitoring a source format with less elements than the current monitor format the elements in the source format that also appear in the monitoring format are passed through to their respective loudspeakers unmodified For example when monitoring a stereo bus through a 5 1 speaker system the left and right bus elements appear in the left and right speakers and the centre and surround speakers are ignored The exception to this where the source format contains a centre or centre surround element and the target format does not In these cases the centre channel is distributed between left and right elements Bass Management The default monitor matrix eliminates the boom or LFE channel when downmixing to a format that does not include a boom channel If it is desired to add the boom signal into the front monitors this may be done by adding the appropriate entries to the monitor matrix file as described below Pyxis G2 Page 157 Operator Reference Manual CHAPTER 24 SYSTEM FILES September 15 2011 Editing the Monitor_Matrix File The monitor matrix data is contained in a readable text file on the Pyxis G2 computer The file specifies both downmix and upmix combinations Thi
172. y on the QWERTY or the BLUE key on the DREAM II controller keyboard causes the clip to be selected or deselected if it was already selected In addition a range is created exactly large enough to contain all clips that were already selected plus the one just clicked Pyxis G2 Page 35 Operator Reference Manual CHAPTER 4 AUDIO TRACKS amp TRANSPORT September 15 2011 The newly created range does not however select any clips that were not previously selected other than the one just clicked Put more simply Ctrl clicking a clip adds to the selection without selecting any other clips Similarly a clip that was already selected can be deselected by Ctrl clicking as long as it is within a range Pyxis G2 Page 36 Operator Reference Manual CHAPTER 5 VIDEO TRACK September 15 2011 Chapter 5 Video Track Introduction Pyxis G2 s Video Track is a built in video disk recorder and editor The Video Track is also known as the Pyxis Track It can import files of many formats and export to many formats Some of these formats require special licences to operate See below for import export information Creating a Pyxis Track Before using Pyxis Track a video track must be added to the project This can be done in two ways e When creating a new project select the Add Pyxis Track checkbox shown below Dream 2 Set Record Seed Name Add Clip Set Display Level Arm Tracks Solo Tracks Mute Tracks Safe Tracks S

PYXIS G2 User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents