Starpower 548
Contents
1. When the timer reaches 0 the lamps turn off If you want to interrupt your session before time expires press the stop button F Raise the canopy by using the canopy handle do not push up on the acrylic shield The cooling fans run for a period of time after the lamps shut off to aid in cool ing the sunbed The timer will indicate as a reminder to clean the sunbed After the sunbed is cleaned press the timer but ton and the display will return to 0 Vc0 0629c 26790 02A Using Your Sunbed When used as a stand alone unit or when connected to a remote system using a control relay Operation Using Your Sunbed oo em A B C D E F G Face tanner control Turns face tanners on and off during use Face tanner lamps require one minute to relight Shoulder tanner control Turns shoul der lamps on and off during use Body fan control Controls the speed of the body fan during use At your feet Body fan speed indicator ndicates speed of fan OFF LOW MED HIGH Timer display Displays remaining time Stop button Stops tanning session Timer button Turns bed on Timer dis play shows remaining time If a lesser time is desired press timer button until desired time is displayed A WARNING Wear protective eyewear Failure to may result in severe burns or longterm injury to the eyes 1 Lift canopy lie down on the bench face up lower the canopy toward your body2. Timer Keypad Kit circuit board Timer Keypad Pushbuttons Trim Bench Front Trim Canopy Front Warning Label English Warning Label French Wiring Harness Keypad Link Wiring Harness Remote PCB to Timer Wiring Harness Resistor Code Wiring Harness Timer in Tray Wiring Harness RJ 11 Canopy to Bench Not shown Vc0 0629c 26790 02A WHEN What to do After each use Monthly 400 500hrs 600 800hrs Clean Disinfect Interior Surfaces x Clean Lamps Clean Reflectors Clean Exterior Check Clean Fanst k Xj X X Change Lamps and Starters X Tl OLO gt Check Fasteners nuts bolts etc Check Power Cords J Change Filters x See Care and Maintenance See Lamp and Grill Replacement See Final Adjustments t Fans are located on top of the canopy under the bench in the shoulder tanner and body fan and at the side of the ballast drawer Use a vacuum to clean MAINTENANCE LOG What When What When What When om B DE 4 15 04 x poe Record this information for ease of service Po Date of purchase poi Bench serial number Canopy serial number Ballast tray ID number STARPOWER 548 Size Weight Pounds 1050 Recommended Room Size 10 D x 10W Electrical Voltage AC 220 Amperage 46 Circuit Breaker Amps 60 Outlet Hardwire Main Lamps see page iii BRONZING SUN PLUS Velocity amp VS R Ballasts 10
3. This is a list of parts which may be replaced by the consumer When calling for parts first state your bed model as P 548 4F Then refer to this list and preceding illustrations for proper identification Access Panel Access Panel Key Acrylic Bench with aluminum frame Acrylic Canopy with aluminum frame Acrylic Rear Lamp Module Acrylic Shoulder Tanner Ballast 100W bench lamps Ballast 160W canopy lamps Ballast 80W shoulder tanner lamps Ballast 400W face tanner lamps Body Fan complete kit Capacitor 75uF Contactor Cover Canopy Current Sensor Damper Endcap Bench Foot End Endcap Bench Head End Endcap Canopy Foot End Endcap Canopy Head End Endcap Rear Lamp Module Foot End Endcap Rear Lamp Module Head End Fan 6 Fan Round Fan Square Filter Handle Kit Hardware Kit Assembly Hardware Kit Canopy Hour Counter Ignitor Lamp Holder w Starter Lamp Holder w o Starter Lamp Holder Face Tanner Lamps Panel Left Pedestal Front Panel Right Pedestal Front Pillow Relay Remote Connection PCB Remote Control Bypass Plug Schematic Packet Shoulder Tanner complete kit Shroud Body Fan Inside Shroud Body Fan Outside Shroud Shoulder Tanner Inside Shroud Shoulder Tanner Outside Speakers pair Starter K 12 main lamps Starter S 2 shoulder lamps Support Bench Acrylic kickstand Thermostat for face tanner Timer Timer Interlink PCB
4. NO 224 88465 VTo06 97 26790 02A Renseignements sur la S curit D AN GE Rayonnement ultraviolet Veuillez suivre les instructions vitez une exposition excessive Tout comme pour les rayons du soleil une exposition excessive peut causer des blessures aux yeux et la peau et provoquer des r ac tions allergigues Une exposition r p t e peut causer le vieillissement pr matur de la peau et provoquer le cancer de la peau PORTEZ DES LUNETTES PROTECTRICES LE NON RESPECT DE CETTE CONSIGNE DE S CURIT PEUT ENTRA NER DE GRAVES BR LURES OU DES L SIONS OCULAIRES LONG TERME Les m dicaments ou les produits cosm tiques peuvent augmenter votre sensibilit au rayonnement ultraviolet Consultez un m decin avant d utiliser la lampe solaire si vous prenez des m dicaments si vous souffrez d une maladie cutan e ou si vous croyez tre particuli rement sensible aux rayons du soleil Si vous ne bronzez pas au soleil il est peu probable que vous bronzerez sous une lampe solaire Les enfants les personnes g es et les personnes qui ont une peau claire qui br le facilement ne bronze jamais ou alors tr s peu ne devraient pas utiliser cette lampe tendez vous sous la partie sup rieure puis abaissez celle ci aussi bas que possible en veillant cependant conserver un espace d au moins 3 pouces 760 centim tres entre le corps et le panneau de plastique transparent de la partie sup rieure afin d viter une expo Sition excessi
5. clips and swing up to hold the acrylic open You may remove the acrylic by lifting it out of its hinge channel along the back edge The other acrylics are held in place by four guarter turn latches each The canopy and rear lamp module acrylics also swing open on a hinge and may be removed by lifting out of the channel along the back edge When you are finished simply reverse the above directions to secure the acrylic shields 22 Care and Maintenance Lamp and Acrylic Replacement CANOPY ACRYLIC REAR LAMP MODULE ACRYLIC BENCH ACRYLIC ACRYLIC SUPPORT 26790 02A Removing Replacing Lamps After opening or removing the acrylic shields replace lamps as follows Step 1 Grasp a lamp at one end and at the middle and turn the lamp one quarter turn Gently remove the lamp from its holders Step 2 Reinstall the lamp by inserting the pins located on the ends of the lamp into the slots on top of the lamp holders and turn the lamp a quarter turn It should click in place Care and Maintenance Lamp and Acrylic Replacement Recommended Replacement Lamps We recommend using the lamps specified below Use of uncertified lamps is a viola tion of Federal regulations and will void your warranty The 100W lamps have an average life of 800 1000 hours of effective tanning use The 160W lamps have an average life of 600 800 hours Lamps used longer than that begin to lose their effec tiveness even though they
6. instruction sheets included in their respective boxes Installation Assembl Procedures Slide the ballast tray under the unit and pull the cords through to the rear Install the access panel by putting it in place and locking with the access panel key VTo 06 97 26790 02A Electrical Connections At the rear of the sunbed connect the two canopy power cords two bench power cords and rear lamp module cord from the ballast tray to their respective power recep tacles Simply match the plug to the recep tacle push on firmly and secure by twisting the threaded locking ring PIN CONFIGURATIONS MAY VARY FROM SHOWN Jj REAR LAMP MODULE J POWER BENCH POWER Installation Electrical Connections Helpful Hint Line up the plug with the proper receptacle and push in Apply pressure to the plug and twist the locking ring counter clockwise until you feel the plug click into place Then turn the lock ing ring clockwise to secure it The ring will click when fully engaged Connect the RJ 11 phone type cable between the canopy and rear jack on the ballast tray The double jacks on the front of the tray are for remote connections Connect main power cord as described in Pre Installation Planning CANOPY POWER Mover AdONVO OL Rear of ballast tray shown Installation Final Adjustments Final Adjustments Your sunbed uses a smooth gliding spring lift system to raise the canopy This
7. lift sys tem may need to be adjusted slightly due to shipment Remove the front access panel Use a wrench to turn the hex shaped Lift Adjustment lugs shown below clockwise for more lift and coun terclockwise for less When adjusted properly the canopy should raise easily as well as rest fully closed Always adjust both lugs equally AIR FILTERS Make sure the air filters are in place The filter on top of the ballast tray simply sits over the vent holes Airflow holds it in place when the unit is on The airflow arrow on the side of this filter should point down The filter hanging under the bench should be installed with the arrow point ing up MAINTENANCE HEIGHT RELEASE HANDLE LIFT ADJUSTMENT LIFT ADJUSTMENT VTo 06 97 26790 02A Remote Connections Your sunbed incorporates advanced cir cuitry allowing it to connect and com municate with most remote control sys tems If a remote system is to be used first determine whether the remote sys tem is a T Max System or a standard remote system operating with a control relay Follow the appropriate instructions for your system type Two remote ports are located on top of the ballast tray at the front Both ports work the same A Remote Control Bypass plug is already installed in one of the remote control ports Your sunbed will not operate without the Remote Control Bypass plug or a remote system connected ATTENTION Although the Remote Con
8. out and resume its session after power is restored Consult your T Max amp Manager manual for information on setting parameters 26 P 548 4F canopy cover removed and electrical shields cut back ENDCAP CANOPY LAMP HOLDER W O STARTER SNITOR FAN ROUND ENDCAP CANOPY FOOT END ACRYLIC REAR LAMP MODULE ENDCAP REAR LAMP MODULE FOOT END PANEL RIGHT PEDESTAL FRONT WARNING LABEL FRENCH WIRING HARNESS WARNING KEYPAD LINK LABEL ACCESS ENGLISH PANEL LAMP HOLDER TRIM BENCH W STARTER FRONT ENDCAP BENCH FOOT END PANEL LEFT PEDESTAL FRONT Vc0 0629c Shoulder Tanner LAMP HOLDER W O STARTER BEHIND COVER BALLAST 80W ENDCAP REAR LAMP MODULE HEAD END SPEAKER FAN 6 R 9 Y We SHROUD SHOULDER TANNE INSIDE removed x m ud Hu O amp O Dea a ONZ gt gt I z ui m outside shroud Vc0 0629c FAN ROUND FAN ONLY SHROUD BODY FAN OUTSIDE SHROUD BODY FAN INSIDE VTo06 97 26790 02A Ballast Tray RELAY BED FANS CAPACITOR CONTACTOR CANOPY FAN SQUARE TIMER H X O Sr cO oy ki Z m DW t2 O OO pan a Ok LU Z tw EO 39 OF t 19 rz z O O S ET 35 H Lu za m osa 3 Ho a a N 0 D gt o S z lt z Z zo H H ZZ E O O K N o T O LOT x oX Jg rZ Z se Ug x Zi zt FE Z Parts List
9. using the canopy handle Maintain at least 3 between your body and the canopy and rear lamp module acrylics Put on your safety goggles Press the timer button C to begin the tan ning session The lamps will turn on and the timer will begin to count down If a tanning time less than the displayed time is desired repeatedly press the timer button C to decrease the remaining time When the timer reaches 0 the lamps turn off If you want to stop your session before time expires press the stop button F You will have ten seconds to restart with the remaining time otherwise the timer will reset to O Raise the canopy by using the canopy handle do not push up on the acrylic shield The cooling fans run for a period of time after the lamps shut off to aid in cool ing the sunbed 20 Care and Maintenance Cleaning After Use Clean and disinfect your tanning bed s bench canopy and rear lamp module after each use Use a non abrasive disinfectant cleaner that does not contain ammonia or ammonia derivatives Ammonia may dam age the acrylic shield Spray the acrylic lightly with disinfectant and wipe dry with a clean soft cloth We recommend SunQuest disinfectant and SunOuest acrylic cleaner Thorough Periodic Cleaning Introduction The cooling fans draw air through the bed and over time will cause a dust buildup on the lamps and reflectors This will reduce the tanning effectiveness of the bed When a dus
10. 0W bench 160W canopy Face Tanner SolarMax IFT FT Ballasts 400W Cooling System 825cfm body fan at foot end 220cfm fan at head end Timer System Digital Max Exposure Time 12minutes Back up Timer Digital watchdog circuitry Remote Capability T Max amp compatible L4 TS Proudly manufactured U S Patent 6 660 025 B2 ETS in the U S A M A
11. Contact servicer Timer display is indicating Er 94 Reguested session time exceeds maximum time allowed Timer display changes to indicate 1 Bypass plug is not installed see Remote Connections a tanning time after the timer but 2 A non SunStar amp bypass has been used See Remote ton is pressed but lamps do not Connections come on 3 If remote is being used other than T Max amp Manager the external timer may not be activated 4 Remote wiring is incorrect see the instructions provided with the remote interface kit My bed is connected to the T The auto start feature of the remote system is disabled see the Max amp Manager remote system and instructions provided with your remote system when the delay time has expired the timer display starts counting down but the bed lights do not come on My bed won t work with the T 1 The sunbed must first be set to a unique address see Remote Max amp Manager remote system Connections 2 The bypass or terminator plug may be installed in the series in an inappropriate location Plug the bypass plug only into the bed at the end of the series Timer display continues to show a 1 T Max amp Manager remote system has not yet been set O after the timer button is pressed 2 Sunbed address is not set correctly see Remote Connections 27 VTo 06 97 26790 02A Problem My bed is connected to a T Max amp remote system but am having trouble getting into id mode My bed co
12. Planning 2 Tools Requiled Lit ia uos A E pt eee 3 Hardware Inventory 3 Assembly Procedures 5 Electrical Connections 12 Final Adjustments ies vs ase sea eee a RR YU 13 Remote Connections 14 Operation see ue eee ek eeu eee SISSI A A ERE ER REPE uses 18 Before Yo Tali 2 grue tim ryan Pe nee deno PAA v ASEITA 18 Expos re TIMES c ous te a se men ges ane mal he 18 Using Your Sunbed stake data dense Welt 19 Care and Maintenance viuo naar etai 21 Cleaning After Users serere iex Sun DT 21 Thorough Periodic Cleaning 21 Mechanical Inspection 21 Lamp and Acrylic Replacement 22 Troubleshooting 4 4 26 Satety Information D AN GE Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin cancer WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or have a history of skin problems or believe yo
13. Sus ISK avance TecHnovocy 838 308 B 4 3V STANDARD 48 MONTH WARRANTY Your ETS Distributor including ETS Inc if purchased directly through a manufacturer s warranty warrants your tanning unit to be free of structural defects in material and workmanship under normal use for its lifetime Your ETS Distributor will at its discretion repair any structural defect which materially affects the performance of the tanning unit or replace the tanning unit For forty eight 48 months following the shipping date of your tanning unit your ETS Distributor will provide replacements for parts that prove to be defective in material or workmanship Fluorescent lamps and lamp starters are warranted against manufacturer s defects for a period of ninety 90 days following the shipping date of your tanning unit Acrylics will be warranted against manufacturer s defects for a period of 1 year prorated Labor costs associated with repair or replacement work covered by this warranty will be reimbursed for repair or replacement work required to be performed for a period of one 1 year following the shipping date of your tan ning unit Normal wear and tear damage from misuse or abuse damage incurred in transit or damages resulting from unauthorized repairs or modifications are not covered by this warranty Warranty coverage does not include cosmetic abnormalities such as scratches nicks dents or other cosmetic changes that do not materially in
14. an now be Unfiltered light from face tanner can exchanged The lamp holders cause severe burns are equipped with spring con Never turn sunbed on while face tacts which enable the lamp to tanner is disassembled or when be removed easily Remove the glass filters are removed old lamp and discard Install the Immediately discontinue use of this new lamp using a clean cloth equipment if face tanner glass is or paper towel Ensure that the broken or any unfiltered light can be lamp is firmly seated in the seen escaping face tanner assembly lamp holders RETAINING SCREWS GL BE 09 25 VTo 06 97 26790 02A Iroubleshootin Problem Solution Sunbed not tanning 1 Clean sunbed see Thorough Periodic Cleaning 2 Ensure supply voltage is between 208 and 230V AC 3 Replace lamps if lamp hours are greater than 800hrs 4 Replace acrylic Lamps fail to light and timer dis 1 Make sure the unit is connected to a power source play is blank 2 Checksource of AC power Reset circuit breaker or replace fuse The last minute of tanning time If the timer button has been pressed to decrease tanning time does not count down from 59 sec during the session the time expired in the current minute is onds but some time less than 59 subtracted from the last minute seconds One or more lamps fail to light Check that lamp is installed correctly Switch unlit lamp with a lamp that lights if new lamp lights a
15. ce VTo 06 97 26790 02A Installation Pre Installation Plannin Pre Installation Planning Before you begin to assemble your sunbed you should observe the following considerations A WARNING A CAUTION Shock hazard Use of a voltage source above 230V Disconnect power before AC may prevent proper operation of servicing the sunbed and could cause damage and void the warranty e The STARPOWER 548 operates from a 220V AC power source The ME A CAUTION unit should be wired to a dedicated Air from the room is used to cool circuit capable of providing 60 Amp the sunbed Maximum ambient room service This unit must be hardwired temperature should be 80 F Place directly to a junction box We rec YOU sunbed no closer than 6 from ommend connection by a profes ANY wall Make sure nothing sional electrician obstructs the airflow into or out of the fan openings A poorly ventilated e IMPORTANT Voltage must be below room may cause the unit to become 230V AC or may require a Buck hot and cause discomfort to the Booster user A CAUTION Proper assembly of your sunbed requires four people Plan to have a few helpers assist you Installation Tools Required Tools Required You will need the following tools to assemble your sunbed 2 Phillips Screwdriver AND 9 16 and 7 16 Wrenches OR Adjustable Wrench Hardware Inventory Open the hardware bags and remove t
16. continue to light Recommended Replacement Acrylics Acrylics vary greatly over time in their ability to effectively transmit UV light Acrylics sold by ETS have been life tested to ensure proper transmission throughout their useful life ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT Bench lamps BRONZING SUN PLUS Wolff Model BSP 71 T12 100WR BI PIN or SPEED 225R Wolff Model SPD71 T12 225R Bi Pin Canopy and rear lamp module lamps Velocity amp VS R Wolff amp Model VEL71 T12 160W VS R Bi Pin or SPEED 315 VS R Wolff amp Model SPD75 T12 315VS R VS R Bi Pin SolarMax M IFT facial unit Heraeus E400 HPT or Philips Model HPA 400 30s or CosmoTech Model 23045 Shoulder tanner COSMOLUXE RA plus 15504 40W 24 Care and Maintenance Lamp and Acrylic Replacement Removing Replacing Face Tanner Note Never take hold of the lamp such Lamps that your fingers are in contact with the After removing the canopy and or rear lamp glass Finger oils will greatly reduce lamp module acrylic shields replace the the lamp s operational life face tanner lamps as follows Step 3 Gently close the face tanner Step 1 Support the face tanner assembly with your hand while unscrew ing the two retaining screws The face tanner glass casing will glass casing and lock it closed with the screws Ensure that the screws firmly secure the glass casing swing downward 4 DANGER Step 2 The lamp c
17. ernative a shower cap or towel can be worn to keep treated hair away from the sunbed surfaces This unit intended for individual use Only one pair of eyewear is included RECOMMENDED EXPOSURE TIMES IN MINUTES Level 1 Week 1 1st 3rd Sessions Skin Type DANGER Some medication may increase your sensi tivity to ultraviolet light It is recommended that you consult a physician before using this sunbed if taking any medication or if you suspect that your skin might be espe cially sensitive to sunlight DANGER Shock hazard Do not operate this device near water or while you are wet Exposure Times Follow the guidelines for skin type and exposure times as shown in the table below Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approxi mately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan MAXIMUM EXPOSURE TIME IS 12 MINUTES Subsequent Level 4 N Maximum Level 2 Level 3 I Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING II Light Burns easily and severely and tans minimally 10 12 III Normal IV Dark Burns moderately and tans average Burns minimally tans easily and abo
18. established by your ETS Distributor If your tanning unit must be returned for service all freight charges shall be at your expense Contact your ETS Distributor for the authorized Service Center nearest you This war ranty is serial number specific and only applies to tanning units purchased through an authorized ETS Distributor This warranty is extended to the individual or legal entity whose name appears on the original sales document and may not be transferred to any other individual or legal entity This warranty is void if the tanning unit is modified in any manner from its original design To obtain warranty service contact your place of purchase Proof of purchase including serial num ber is required for verification Contact ETS Inc only if you purchased your equipment directly ETS Inc 7445 Company Drive Indianapolis IN 46237 9296 l 1 800 449 3605 In Canada call 1 800 661 6292 or 519 421 1212 Vc0 0629c 26790 02A eicome Congratulations on your purchase of this technologically advanced sun tanning unit It has been designed to provide years of dependable service for you Please read all the instructions in this booklet before installing and using the unit Always be sure to observe all safety precautions Contents Safety Information iii installation spada nra RSS wees eee ie Rees Re brke Qd 1 Unpacking and Inspection 1 Pre Installation
19. he hardware In addition to a pillow an RJ 11 phone type cable and touch up paint make sure you have the following hard ware items 10 x 1 Phillips Pan Head Screw Quantity 14 10 x 1 2 Phillips Pan Head Screw Quantity 12 3 8 16 x 1 1 4 Hex Socket Bolt Quantity 18 Hex Nut Quantity 18 3 8 16 Self locking 55 VTo 06 97 26790 02A Canopy Adapter Arm Quantity 2 o o o Adapter Gusset Ouantity 4 O O O Safety Goggles Quantity 1 Access Panel Key Quantity 1 5 16 Allen Wrench Quantity 1 Installation Hardware Inventor Additional hardware in Body Fan box e 10 x 1 2 Phillips Pan Head Screw Quantity 5 Hardware in Shoulder Tanner box 10 x 1 2 Phillips Pan Head Screw 1 4 20 x 1 1 2 Hex Head Bolt Quantity 4 Quantity 4 5 16 Washer Quantity 4 5 16 18 Stud Quantity 4 5 16 18 Self locking Hex Nut Ouantity 4 1 4 Allen Wrench Ouantity 1 Installation Assembly Procedures Assembly Procedures Before installing the bench endcaps you must install the body fan power cord into the foot end endcap as shown below and the shoulder tanning unit power cord into the head end endcap The connector will snap securely into the endcap Snap body fan power cord into hole in foot end endcap BODY FAN POWER CORD Foot end endcap shown 5 Vc0 0629c 26790 02A Foot end endcap shown E Installat
20. ices lorsque les lampes sont allum es Coquilles de protection pour les yeux recommand es Les coguilles de protection fournies ou l quivalent tel que le stipule le document 21 CFR 1040 20 Les autres types de lunettes protectrices peuvent ne pas assurer une protection ad quate Utilis sans lunettes protectrices ce produit peut causer des br lures ou l sions oculaires graves Si vous souffrez d un malaise arr tez l utilisation et consultez un m decin SEULES LES LAMPES SUIVANTES ONT T HOMOLOGU ES POUR CET QUIPEMENT BRONZING SUN PLUS Wolff Mod le BSP 71 T12 100WR BI PIN ou SPEEDO 225R Wolff Mod le SPD71 T12 225R Bi Pin banc seulement Velocity VS R Wolff Mod le VEL71 T12 160W VS R Bi Pin ou SPEEDO 315VS R Wolff Mod le SPD75 T12 315VS R VS R Bi Pin partie sup rieure et appareil de bronzage lampes lat rales Heraeus E400 HPT ou Philips Modele HPA 400 30s ou CosmoTech Modele 23045 unit faciale COSMOLUX RA plus 15504 40W unit en bandouli re p n A n qu D brancher l alimentation lectrique avant de nettoyer l appareil d en faire l entretien ou de changer les lampes Cet quipement doit tre mis la terre Ce produit est conforme aux normes de rendement pour les lampes solaires dans le documents 21 CFR partie C US 1040 20 ANSI UL 482 CAN CSA C22 2 N 224 88465 iv Installation Unpacking and Inspection Your sunbed comes in two cardboard car tons one for the can
21. ion Assembly Procedures Parts needed Foot end endcap Head end endcap 14 10 x 1 Phillips pan head screws 4 10 x 1 2 Phillips pan head screws Attach endcap with 1 screws as shown Use 1 2 screws here Installation Assembly Procedures Parts needed Canopy 2 Canopy Adapter Arms 4 Adapter Gussets 12 3 8 x 1 1 4 hex socket bolts 12 3 8 self locking hex nuts CANOPY ARM Attach adapter arms to canopy arms using two adapter gussets and six bolts and nuts ADAPTER GUSSET ADAPTER ARM Vc0 0629c 26790 02A Installation Assembly Procedures Parts needed 6 3 8 x 1 1 4 hex socket bolts 6 3 8 self locking hex nuts CANOPY 1 Install this bolt as a Vg positioning aide 2 Slip canopy arm onto hinge arm Positioning bolt will engage the slot on top of hinge arm and hold canopy up while the other bolts are installed 3 Install other bolts as shown Secure all six bolts in place with self locking nuts 4 Remove this pin and discard Installation Assembly Procedures Parts needed Rear lamp module Secure rear lamp module in place with 8 screws where shown VTo 06 97 26790 02A Installation Assembly Procedures Parts needed Body fan kit Shoulder tanner kit LORS 6 SES Install the body fan and shoulder tanner as described in the
22. nd old lamp still does not replace old lamp The face tanners will not Face tanner operation is initially delayed by 5 seconds come on Face tanners will not relight until cooled Replace face tanner lamp see Removing Replacing Face Tanner Lamps The canopy will not stay up Your sunbed uses a smooth gliding spring lift system to raise The canopy will not stay down the canopy This lift system may need to be adjusted slightly from time to time See Final Adjustments for proper adjustment procedures The canopy should raise easily as well as rest fully closed My canopy opens and closes too Your sunbed utilizes a damper which limits the canopy s fast slamming not enough resis movement speed This also serves as a safety device in case of tance spring lift failure as the canopy will not crash down Replace the damper on back of unit forgot what address or id set By holding the body fan button for 3 seconds the timer display my sunbed to will briefly display three numbers the installed timer software version a factory set timer code and then the sunbed s id number 26 Troubleshootin Problem Solution Timer display is indicating Er 91 Timer software error Disconnect and reapply power to the unit Timer display is indicating Er 92 Current sensor indicating unit is off when it should be on Contact servicer Timer display is indicating Er 93 Current sensor indicating unit is on when it should be off
23. ness change 100W lamps after approximately 800 1000 hours of use Change 160W lamps after 600 800 hours of use Tanning will continue after this time but at a slower rate To ensure trou ble free operation of your sunbed replace the lamp starters whenever the lamps are replaced A WARNING Shock hazard Disconnect power before removing any protective covers Maintenance Height Feature The STARPOWER 548 offers a conve nience feature when maintenance must be performed Behind the front access panel is a release handle see Final Adjustments With the canopy open pull this handle and raise the canopy to its maintenance position allowing easier access to lamps etc When finished sim ply close the canopy to return to normal operation Care and Maintenance Lamp and Acrylic Replacement Opening Replacing Acrylic Shields Refer to the illustration on the next page while reading this instruction The acrylic shield in the bench is secured in place by two guarter turn latches along the front aluminum frame of the acrylic The alu minum frame around the acrylic offers support as well as allowing the acrylic to hinge open without removing it from the bed Use a coin or flat bladed screwdriv er to turn the latches a guarter turn to open the acrylic Standing in front of the bed lift the long edge of the acrylic On the inside of the bench along the front are two supports for the bench acrylic Release them from their
24. nnected to a T Max amp Manager did not display dL but does indicate Q a tanning time and the lamps have come on a tanning time but the lamps have not come on When auto addressing the first bed does not register an id When using a T Max 1A my sunbed won t function properly My salon suffers frequent short power outages and clients com plain about losing session time Troubleshootin Solution You have probably attempted to connect your sunbed to the remote system already Disconnect the remote plug s from the ports at the front of the ballast tray wait 90 seconds and try again Remote device has not been set The sunbed has not been connected to the remote system see Remote Connections Delay time of T Max amp Manager has not been set Delay time has expired and session has begun Auto start function of T Max amp Manager has been turned off Press the timer button to turn on lamps When using the auto address feature of the T Max amp Manager you must wait 10 seconds from the time you start the auto address function before addressing the first bed SunStar Bypass plugs or terminator plugs may be needed if the T Max TA and the sunbed are over 100 feet apart Install the plugs in the open remote port in the sunbed and the T Max TA If you have a T Max amp Manager changing parameter 23 from 0 to 1 will allow the tanning bed to remember how much time was left when power goes
25. opy and one for the bench and ballast tray Open the cartons and remove the sunbed parts as follows The boxes that the STARPOWER come in dismantle to allow easy removal of the units Remove the box tops and pull the sides out The bench and canopy are each wrapped in plastic Remove the plastic and with a helper or two grasp the canopy and pull it from the carton bot tom Do the same for the bench Do not attempt to lift either unit with the plastic still on as it may slip The endcaps on the canopy should not be used to lift the unit The ballast tray is secured to the carton bottom with brackets Remove these brackets from the ballast tray with a Phillips screwdriver Note The cartons are reusable You may wish to save them for future use After unpacking the unit check to make sure you have received the following e Canopy unit e Bench unit e Rear lamp module e Ballast tray e Access panel Two large bench endcaps e Body fan kit e Shoulder tanner kit e Two bags containing necessary assembly hardware safety goggles a pillow and a tube of touch up paint Inspect these items including the canopy and bench to make sure they are free from any visible damage Report the extent of any damage to the transportation company Record the serial numbers of the canopy and bench and the ballast tray ID number in the area provided at the back of this manual This information will be reguired whenever you call customer servi
26. ress to 1 see righ simply connect the RJ 22 modular cables described in the T Max user s guide directly into either port located on top of the ballast tray at the front and either port on the back of the T Max 1A or 3A See figure 2 figure 2 NOTE A T Max TA with a master chip can be substituted for a 3A in figure 2 Installation Remote Connections Setting the address manually Before connecting your sunbed to the T Max amp Manager or T Max TA or 3A the address of your sunbed must first be set Set the id man ually as described below Setting the id 1 Make sure no cables are plugged into your sunbed s remote ports 2 Remove and reapply power to the unit 3 Press and hold the stop button located on the sunbed display for three seconds and release The display should indicate an id number from oF to 252 1 99 AT 100 199 399 20252 52 4 If you are using a T Max 1A or 3A asa master remote the id of the sunbed must be set to 1 If you are using a T Max amp Manager each sunbed must be assigned a different id To set the id press the timer button to count up or the body fan control button to count down until the desired number is achieved 5 Press the stop button to return to the normal display mode Installation Remote Connections Remote systems using a Control Relay Most non T Max remote systems control the sunbed by the
27. t buildup is observed it is necessary to thoroughly clean the inside of the unit A WARNING Shock hazard Disconnect power before removing any protective covers Cleaning the Canopy and Bench Step 1 Remove the acrylic shields and lamps as described in Lamp and Acrylic Replacement With a soft cloth wipe the entire length of each lamp Step 2 21 Step 3 Clean both sides of the acrylic shields with a non ammonia dis infectant cleaner Step 4 Wipe the reflectors with a clean damp cloth Step 5 Reinstall the lamps and acrylic shields Step 6 Clean or replace air filters on top of ballast tray and under bench see Final Adjustments Replace with 10 x 24 x 1 furnace filters Mechanical Inspection Your tanning bed has been built for years of service To ensure trouble free operation throughout its life inspect the unit s mechanical integrity every 400 500 hours of use e Inspect the units fasteners verifying that all are firmly in place Inspect lift adjustment Adjust for prop er lift if needed See Final Adjustments Inspect the AC power cord and its connections Inspect the acrylic Broken cracked or badly scratched acrylics should be immediately replaced e Check damper operation The damper limits the canopy s move ment speed Replace if canopy raises and lowers too quickly Vc0 0629c 26790 02A Lamp and Acrylic Replacement Introduction To be assured of maximum tanning effec tive
28. terfere with the function of the tanning unit THIS STANDARD 48 MONTH WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE HEREBY DISCLAIMED No one has the authority to change or modify this Standard 48 Month Warranty in any respect To obtain service under this Standard 48 Month Warranty contact your authorized ETS Distributor or ETS Inc if purchased directly Proof of purchase includ ing serial number is required IN NO EVENT SHALL YOUR DISTRIBUTOR OR THE MANUFACTURER BE LIABLE AT LAW OR IN EQUI TY FOR ANY LOSS LIABILITY DAMAGE OR EXPENSE IN AN AMOUNT IN EXCESS OF THE PURCHASE PRICE RECEIVED OR FOR LOSS OF USE OR PROFITS LOSS OF TIME INCONVENIENCE RENTAL OR SUBSTITUTE PRODUCTS LOSS OF BUSINESS LOSS OF INCOME OR ANY OTHER INCIDENTAL INDI RECT SPECIAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages and the above limitation or exclusion will not apply to residents of some states This Standard 48 Month Warranty gives you specific legal rights and you may have other rights which may vary from state to state All warranty service must be performed by an authorized service person Al labor charges must be authorized by your ETS Distributor prior to the start of repairs and must not exceed the established rates and time allotment policies
29. trol Bypass plug provided with your sunbed will work wherever a T Max ter minator is called for in the series the T Max amp terminator will not work as a bypass plug Normally a bypass plug is needed only when your sunbed is operat ed without a remote system connected Installation Remote Connections You will notice some wire clamps along the side of the fan housing under the bench These are for the remote cables to keep them out from under the ballast tray when rolling the tray in and out of the unit Route the remote cables as shown below leaving some slack for the tray to roll out FAN HOUSING UNDER BENCH REAR TO REMOTE PORT Installation Remote Connections CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote inter face circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty Go straight to the source with all your T Max amp brand remote guestions 417 338 5101 T Max Manager Other beds figure 1 T Max Products The T Max remote systems offer the ultimate in sunbed control while allowing the tanner easy straightforward operation Your sunbed is configured to directly connect to this system The circuitry inside your sunbed eliminates the need for the T Max amp 1A or 3A when connect ing to the T Ma
30. urself especially sensitive to sunlight If you do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this equipment To use lie down under canopy and pull down as far as adjustment will allow maintaining at least 3 inches 7 6 centimeters between your body and canopy clear plastic panel and side tanner clear plastic panel otherwise overexposure may occur Minimum use distance else where is touching the clear plastic panels Do not use without clear plastic panels in place Untanned persons should not tan on con secutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 12 MINUTES Level 1 Week 1 Subsequent Skin Type 1st 3rd Sessions Level 2 Level 3 Level 4 Maximum Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING II Light Burns easily and severely and tans minimally 4 7 10 III Normal Burns moderately and tans average 9 12 IV Dark Burns minimally tans easily and above average 12 New lamps emit appro
31. use of a relay The relay oper ates the sunbed by connecting and discon necting a pair of wires leading from the sunbed Refer to the user s manual provided with your remote system to determine if it operates in this way To connect your sunbed to this type of system a remote interface kit is required Contact your place of purchase to obtain the kit Figure 3 details a typical con nection Follow the instructions provided with the kit and from the remote s manual to make the necessary connections CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote inter face circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty Non T Max Remote System using control relay Be eh es ee Remote Interface Kit figure 3 VTo 06 97 26790 02A Operation Before You Tan Before using your sunbed please note the following important precautions e Your skin should be free of cosmetics oils or other body lotions prior to tan ning except for those specifically made for use with tanning devices However do not remove natural body oils by bathing or showering immedi ately before tanning Your hair should be free of gels mousses sprays or other hair products prior to tanning These products can cause damage to the sunbed acrylic As an alt
32. ve Les autres parties du corps peuvent toucher les panneaux de plastique transparents N utilisez pas la lampe sans les panneaux de plastique transparents La premi re semaine de bronzage les personnes qui n ont pas un h le initial ne doivent pas se faire bronzer tous les jours Ne vous faites jamais bronzer plus d une fois par jour Le bronzage commence normalement apparaitre apr s les premi res s ances il atteint son apog e au bout d environ quatre semaines Les personnes qui ont d j un teint hale peu vent commencer des niveaux plus lev s selon l importance de leur h le initial TEMPS D EXPOSITION RECOMMAND EN MINUTES LE TEMPS D EXPOSITION MAXIMAL EST DE 12 MINUTES lev 1 Semaine 1 lev 2 lev 3 lev 4 Sem suivantes Type de peau 19 38 Temps maximal Peau sensible br le facilement et ne bronze pas NON RECOMMAND II Peau claire br le facilement et bronze tr s peu 10 12 III Peau normale br le et bronze de fa on mod r e 12 k IV Peau fonc e br le tr s peu bronze plus facilement que la moyenne 12 Les lampes neuves emettent approximativement 10 de plus de rayons ultraviolets au cours des 50 premi res heures de fonction nement Le temps de bronzage doit donc atre r duit d environ 10 pendant cette p riode AVERTISSEMENT Lisez le livret d instructions avant d utiliser cette lampe solaire e Les autres personnes pr sentes dans la pi ce doivent aussi porter des lunettes protectr
33. ve average 2 4 7 3 6 9 12 12 10 12 12 Operation Using Your Sunbed Using Your Sunbed When connected to the T Max amp Manager or T Max 1A or 3A 99 Bi A B C D E F G Face tanner control Turns face tanners 1 on and off during use Face tanner lamps reguire one minute to relight Shoulder tanner control Turns shoul der lamps on and off during use Body fan control Controls the speed of 3 the body fan during use At your feet Body fan speed indicator ndicates speed of fan OFF LOW MED HIGH Timer display Displays remaining time Stop button Interrupts tanning session Timer button Turns bed on Timer dis play shows remaining time If a lesser time is desired press timer button until desired time is displayed A WARNING Wear protective eyewear Failure to may result in severe burns or longterm injury to the eyes Lift canopy lie down on bench face up lower canopy toward your body using canopy handle Maintain at least 3 between your body and the canopy and rear lamp module acrylics Put on your safety goggles Assuming the remote system has been set to allow a pre tanning delay time the timer display E will repeatedly flash the delay symbol dL and then the remaining delay time Press the timer button G or wait until the delay time has expired to begin the tanning session The lamps will turn on and the timer will begin to count down
34. x amp Manager series Your sunbed supports the auto addressing feature of the latest TMax Manager models and the fol lowing parameters 2 5 6 7 8 9 10 14 and 15 See your T Max amp manual for descriptions of these parameters and how they function T Max Manager Remote System This system is ideal for multiple sunbed instal lations Simply connect the RJ 22 modular cable s described in the T Max amp Manager manual into the remote port s located on top of the ballast tray at the front and follow the instructions that came with your remote sys tem noting figure 1 If you have an older T Max amp Manager that doesn t support auto addressing set the address or id of each sunbed manually as described in Setting the address manually You can place your sunbed at any location in the series NOTE A T Max amp 1A can be substituted for the 3A in figure 1 Vc0 0629c 26790 02A T Max 1A and 3A Remote Systems In single sunbed installations the T Max amp 1A and 3A can offer the same control as the T Max amp Manager eliminating the need for a Manager If you re using a 1A in this manner it must have a chip labelled master installed on its circuit board The remote control bypass plug must not be used in this configu ration The 3A may be used as a master with no modification After you have set the T Max amp 1A s or 3A s address to 0 refer to your T Max user s guide and the sunbed s add
35. ximately 10 more ultraviolet radiation during the first 50 hours of operation Recommended tanning times should therefore be reduced by approximately 1096 during that period WARNING Read the instructions booklet before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear provided eyeshields or equivalent eyewear as defined under 21 CFR 1040 20 Other types of eyewear may not provide adequate protection Failure to use protective eyewear may result in severe burns or other eye injury If dis comfort develops discontinue use and consult a physician ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE 548 BRONZING SUN PLUS Wolff amp Model BSP 71 T12 100WR BI PIN or SPEED 225R Wolff amp Model SPD71 T12 225R Bi Pin Bench lamps Velocity VS R Wolff amp Model VEL71 T12 160W VS R Bi Pin or SPEED 315VS R Wolff Model SPD75 T12 315VS R VS R Bi Pin Canopy and side tanner lamps Heraeus E400 HPT or Philips Model HPA 400 30s or CosmoTech Model 23045 SolarMax IFT facial unit COSMOLUX RA plus 15504 40W Shoulder unit DISCONNECT POWER BEFORE ATTEMPTING TO CLEAN RELAMP OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT NTERTE4 THIS EQUIPMENT MUST BE EARTH GROUNDED This product is in conformity with performance standards for sun lamp products under 21 CFR PART 1040 20 and CI c Us LISTED ANSI UL Standard 482 Certified to CAN CSA Standard C22 2
Download Pdf Manuals
Related Search