OWNER`S MANUAL
Contents
1. Inc IP Digital H 264 Video Encoder Series Manual Rev B WIRELESS NETWORK SET UP IP 720IDVRW amp IPO 720IDVRW ONLY The embedded wireless feature allows users to access the IP Video Encoder from nearly any convenient location within the wireless routers networking environment With minimal initial set up the Wireless IP Encoders will only require an access point for communication eliminating the need to run complex physical cables to locations saving money in wire Suspended raceways and labor Wireless Network Set Up Before configuring the WiFi function within the Encoder ensure that your wireless 902 11 b g router has the SSID name and encryption programmed Assuming that the IP device is powered and connected to your workstation open the IE Browser and enter the encoder IP address Select the Settings gt gt Network Parameters gt gt WiFi Parameters Select Static within the Enable WiFi pull down menu Select 802 11b amp 802 11g within the WiFi Specifications pull down menu Click Refresh which will auto populate the available wireless networks Select the required wireless network which will appear in the Current Wireless Network field Enter the network password into the Input Password field and click OK Click the Save button then Reboot the encoder to complete the process 3G NETWORK Models IP 720iIDVR3g amp IPO 720iIDVR3g ONLY Th2. closing of ports necessary for the IP device to access the Internet If you choose to not use UPnP or your router does not support it You must manually configure your router to allow the necessary ports to access the Internet Ports used by the IP encoder are listed in the Device Defaults on page 5 of this manual To use UPnP enable the UPnP function on both the ROUTER and IP ENCODER the port forwarding settings will automatically change on the reboot of the encoder NOTE To manually set up port forwarding consult you router manual do not set UPnP to ON in the IP device if you will use manual port forwarding UPnP Set Up d Open the required network ports in your firewall Refer to your router operating manual for further instructions Assuming that the IP device is powered and connected to your workstation open the IE Browser and enter the encoder IP address Enter your login and password Select the Settings Tab Select the UPnP Section Select On within the UPnP pull down menu SA Click the OK button Click the Save button then Reboot the encoder to complete the process Note If your workstation PC or Laptop is using Windows XP the UPnP interface must be installed This will ensure that the UPnP function detects the IP device on the network Figure A Basic Wide Area Network Connection IP Encoder amp Network Switch SmartPhone Office Copyright 2012 1156488 Ontario
3. e Parfact for network access to remots locations for live or recorded video JP 720iDVR3g IP 720iIDVRw Perfect for dead zone or remote video a Access remote video and siuwve lance cameras applications where there is no local internet in scenarios when pulling or tranching cable is infrastructua ideal for permanent temporary not possible convenient or economical Perfect Rugged P 67 rated LAN 3G amp WiFi systems avaiable to meet the most demanding all weather applications US Offles 1711 Cudaback Avenue Niagara Falls NY USA 14303 Canadian Offiex 1016C Sutton Drive Unit 6 Burlington ON Canada L7L 688 Toll Free 1 686 379 2066 Tel 905 336 9665 Fax 905 936 9082 14 Copyright 2012 1156488 Ontario Inc 5 8GHz All Weather 8 Channel Series Manual Rev M NOTES 15 Copyright 2012 1156488 Ontario Inc 5 8GHz All Weather 8 Channel Series Manual Rev M IT S ABOUT REAL TIME Direct 1 905 336 9665 Toll Free 1 888 379 2666 www Video Transmitters com 16 Copyright 2012 1156488 Ontario Inc
4. 88 and Password 888888 Repeat these steps should you be unable to access the IP device Device Default Parameters IP Encoder Parameter Ci efatt Web Port BD Alarm Host Port 9000 DNS Server Port 8080 Login and Password Parameter L Defaut Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B BASIC CONNECTIONS amp SET UP With so many technical variables in an installation the strongest recommendation we can make is to conduct a bench test After verifying that all components of the system are in good working order and connected properly we can arrive on the job site confident that all of our devices will install with the least amount of on site effort Basic Connection Procedure 1 Physical Inspection of Product e Compare the unit to the product photo on the attached specification sheet e Check for physical damage to the devices contact your distributor or VideoComm Technologies Technical Support immediately should you suspect damage to the unit 2 Bench Testing Your H 264 Network Video Encoder Device e Attach the included rubber duck antenna to the Video Encoder WiFi amp 3G Models Only e Connect power using the supplied power adaptor via the 2 1mm 12VDC barrel jack e Use a separate power supply for each device Do not share power supplies e Connect the Video Output from the camera to the Encoder using standard BNC Male cable connectors Use an RCA to BNC adapter if yo
5. IP Digital H 264 Video Encoder Series Manual Rev B VIDESCOMM TECHNOLOGIES It s About Real Time IP Digital H 264 Video Encoder Series Manual Rev B OWNER S MANUAL 888 379 2666 US Toll Free 905 336 9665 Phone 905 336 9662 Fax www Video T ransmitters com Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B TABLE OF CONTENTS TABLE OF CONTENTS eebe 2 SAFETY NOTICE a E E E EEA 3 INTRODUCTION e anar EEE E T peers EERE E EEE A E E E EE TE OEE E S 3 PARTS EIS EE 4 PRODUCT DE 41 Kr DE 4 CE DINDICA POR EE 4 CONNECTOR TOS o E 5 DEVICE RE E Torrine ee ee EER E EE EE E EA 5 DEFAULT PARAMETERS esac cece lect coralinos ico Eia aE EEUE E AN a EEA Saai 5 BASIC CONNECTION LE 6 PG STA TIC IP ADDRESS SE E 7 USING WINDOWS Ascaso eo aaa 7 STINGS WINDOW ST EE 7 INTERNET EXPLORER ActiveX CONTROL 7 LOGIN PASSWORD E 8 SETTING NEW LOGINS eUS 5 ege E EE da 8 ENCODERIPADDAE Stata 8 WIDE AREA NETWORK E UE 9 As A a OR EE OO o ee ee eet ene eee 9 N ECHST 10 WIRELESS NETWORK SET UP Model IP 720iIDVRw 8 IPO 720iIDVRw ON 10 oC i el 10 AVAILABLE DOWNLOADS Visit Us Online Today www VideoTransmitters com Or KS Central Management Software exe B Central Management Software User Manual 36 Pages 2 4Mb Detailed IP Encoder Owner s Manual 100 Pages 4 3Mb Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B SAFETY NO
6. K gt gt SAVE Figure B Network Video Server Figure C Link Mode WCDMA Figure D Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B 13 APN Name Enter the Access point Name assigned by your Mobile Provider See Figure D D Click OK gt gt SAVE gt gt Reboot Login to the Encoder Default Login 888888 amp Password 888888 D select Settings gt gt 3G gt gt 3G Network D Ensure that the 3G Status field is Connected which confirms a successful transmission through your 3G Network provider See Figure E A Disconnected status indicated that the device has not been programmed proper If this occurs repeat steps 4 17 Figure E 3G Status Connected Once the configuration is complete the 3G Video Encoder can now be viewed anywhere by simply entering the Static Public IP address assigned by your mobile provider into any Internet Explorer browser VideoComm Technologies Customer Service Bus 905 336 9665 1 US Toll Free 888 379 2666 Fax 905 336 9662 E mail info VideoTransmitters com Web Site www VideoTransmitters com Monday Friday 8 30am 5 00pm Eastern Standard Time 12 Copyright 2012 1156488 Ontario Inc 5 8GHz All Weather 8 Channel Series Manual Rev M WARRANTY INFORMATION TERMS amp CONDITIONS VideoComm Technologies herein re
7. TICE L THIS DEVICE COMPLIES WITH FCC RULES PART 15 OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITONS 1 This device may not cause harmful interference and 2 This device must accept any interference including interference that may cause undesired operation of the device ll In order to comply with the FCC IC adopted RF exposure requirements this system will be installed by an authorized professional installer of VideoComm Technologies Installation of all antennas must be performed in a manner that will provide at least 23cm clearance from the front radiating aperture to any user or member of the public lll This is NOT an intrinsically safe device Do not take into area where intrinsic safety is required Bodily harm may result if warning is ignored IV DO NOT OPERATE WiFi or 3G Devices WITHOUT ANTENNA CONNECTED TO ANTENNA PORT Failure to do so may result in damage to the unit and void the warranty V The IP Digital Video Series has been certified by the FCC for use with other products without any further certification as per FCC section 2 1091 Changes or modifications not expressly approved by VideoComm Technologies could void the user s authority to operate the equipment FE Bei S ck besty C 0336 INTRODUCTION This series of network IP video encoders converts analog video to allow for remote digital D1 quality viewing sharing and recording locally or over the internet via laptop PC or SmartPhone Boasting man
8. amages arising out of or in connection with the use or performance of the product or other damages with respect to loss of property loss of revenues or profit or cost of removal installation or reinstallation PRODUCT RETURNS 30 Day Product Return Policy If you are not satisfied with a product you may return it to VCT within 30 days from original date of shipment within the following conditions Original shipping charges are not refundable unless deemed that VCT shipped incorrect item s incorrect quantity ies or original manufacturers defective product subject to VCT validation Returned products will not be accepted unless accompanied with a valid Return Merchandise Authorization number RMA RMA numbers issued by VCT are valid for 15 days Shipments received after 15 days will be refused Returns must include a copy of original invoice the completed VCT packing slip and a detailed statement of reason for return Customer is responsible for all freight charges duties and taxes if applicable The unit must be shipped freight prepaid or delivered to the VCT Service facility in either its original package or similar package affording an equal degree of protection and with instructions indicating the location within Canada or the United States to which the unit will be returned prepaid to VCT in its original packaging or similar packaging that offers an equal degree of protection VCT will charge the full replacement cost for any missin
9. d 888888 O select Settings gt gt 3G gt gt 3G Online Mode O Select Always Online gt gt Click Connect See Figure A Click Save gt gt Reboot Figure ao Rebooting will redirect you to the Login Page may take up to 40 seconds to Reboot Scheduled Close A Start Time 00 HOO M EndTime 00 HOO M Close E Start Time 00 HOO M EndTime 00 HOO M Close A Start Time 00 H 00 M End Time 00 HOO M Close A Start Time 00 HOO M EndTime 00 HOO M Close A Start Time 00 H 00 M EndTime 00 HOO M Close e StartTime 00 H 00 M EndTime 00 H 00 M Close w Start Time 00 H 00 M EndTime 00 HOO M 7 SMS or dialing activation Auto offline when non network connections Standby period 600 s Accept SMS or dialing from specified telephone numbers 13982231994 NoteSeperate telephone numbers with O Manual Control E Auto offline when non network connections Standby period 600 s Ce Disconn OK O Login to the Encoder Default Login 888888 4 Password 888888 O Select Settings gt gt 3G gt gt Dial Up Settings D Link Mode Select ON via the second pull down See Figure B Important To ensure that the command has been saved successfully confirm that the first Link Mode field has been automatically changed from None to WCDMA If the field does not change repeat this step until the change is complete See Figure C Click O
10. d ap ter Owner s Manual amp Quick Start Guide One Year Limited Warranty PRODUCT DESCRIPTION Minimum System Requirements The H 264 Network IP Video Encoder Series includes an embedded web server which provides users full access to all features and settings through a standard web browser To access the device settings your workstation will need to meet the following specifications CPU Pentium 4 2 4Ghz or above Memory 128MB or above Operating System Windows XP with SP2 or above Windows Vista Windows 2003 or Windows 7 Internet Explorer 6 0 or above LED INDICATORS NETWORK PORT LAN STATE Pei Flashes for Encoder Self Check Feature POWER Pei Solid for Power Input Indicator Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B Connectors LOS Slots Device Hard Reset Each IP Video Encoder includes a convenient Reset button which is used to restore the factory default settings Sp Disconnect the Power Adapter from the DC 12V input plug to power OFF the device ED Press and HOLD the reset button by inserting the supplied paper clip into the RST terminal while simultaneously reconnecting the power adapter O Continue to HOLD the RST button for 15 20 seconds until the red STATE LED becomes solid 14 To confirm a successful Hard Reset access the Encoder through a standard internet browser using the Default IP Address Login 8888
11. e 3G Desktop Network IP Video Encoder is perfect for dead zone or remote video applications where there is no local internet infrastructure Ideal for permanent temporary or mobile applications from anywhere there is a 3G mobile data network Important Your IP Video Encoder MUST have an Activated SIM Card in order to function and access your 3G Network Services To purchase and activate a SIM Card and network services you must contact your preferred Mobile Provider When activating your SIM card it is critical that you request a Static Public IP Data connection which provides remote access to the Encoder over a 3G Network 3G NETWORK SET UP Eject the SIM Card Tray by inserting a paper clip into the eject port Figure A 2 Place SIM Card with the chip facing up on the SIM card tray and push in until secure Figure B NOTE The SIM card is not included and MUST be Purchased and activated from your Mobile service provider Figure A Figure B Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B e Power the IP device using the supplied 12VDC plug in power adaptor Ensure that the RED PWR LED is Solid to confirm the device is ON Connect the IP Device to an Enabled RJ45 LAN input on your PC with the included 3 Network Cable Open an Internet Explorer browser and enter the device IP address Default 192 168 1 19 Login to the Encoder Default Login 888888 amp Passwor
12. e to your workstation using supplied 3 ft network cable EH Power the IP Device using the 12 VDC Plug In adaptor Open IE Browser and enter the encoder default IP address Enter your new login amp password Beck runner Network Parameters T O Select the Settings Tab gr Select the Network Parameters Tab O select the IP Address amp Ports Section Ensure that the Connection Type selected is Static IP Address Change the address to the desired number in the IP Address Field ioe D Click the Save button then Reboot the encoder to complete the process Important When selecting a new IP address the last three digits xxx should be a number from 1 to 254 It is critical that the IP device is given a unique address that is not used by any other device connected within the same network Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B WIDE AREA NETWORK WAN SET UP Now that you have successfully set up the IP video encoder to your local area network LAN the device can be configured to a wide area network WAN for remote access enabling multiple authorized users to view live and recorded video at any time and from virtually any networked location in the world The IP Video Encoders include support for UPnP through the embedded web server This protocol when enabled will automatically set up all necessary port forwarding and manage the opening and
13. e valid for 15 days Shipments received after 15 days will be refused The unit must be shipped freight prepaid or delivered to the VCT Service facility in either its original package or similar package affording an equal degree of protection and with instructions indicating the location within Canada or the United States to which the unit will be returned The repaired unit will be returned to the customer freight prepaid unless the warranty claim is deemed void or invalid All accessories included with the unit must be listed individually on the packing slip for the shipping documentation VCT will not accept any liability for loss or damage to such accessories if they are not listed Proof of Purchase Date This warranty applies and commences to VCT products from the original date of purchase from an Authorized Re seller Proof of purchase i e photocopy of invoice must be included with product when submitting for warranty repair Warranty Limitations This warranty does not cover maintenance or check ups if required This warranty gives you specific legal rights and you may also have other rights which vary from state province to state province Some states provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts therefore the above exclusions or limitations may not apply to you VCT is not responsible or liable for indirect special incidental or consequential d
14. ferred to as VCT LIMITED WARRANTY VCT hereby warrants subject to the conditions here in below that should this product become defective by reason of improper workmanship or material defect during the specified warranty period VCT will repair the same effecting all necessary parts without charge for either parts or labor or replace the unit at VCT option Labor ONE 1 Year from the date of original purchase from authorized Re seller TWO 2 Years for Antennas only Parts ONE 1 Year from the date of original purchase from authorized Re seller TWO 2 Years for Antennas only Void Warranty Purchaser warranty will be void and purchaser waves any rights to make warranty claim if product has been opened altered or modified repaired or serviced by anyone other then the service facilities authorized by VCT to render such services Further the seal serial number on the unit must not have been altered or removed The unit must not have been subject to accident misuse abuse or operated contrary to the instructions provided The opinion of VCT with respect to this matter shall be final This warranty does not include and is not extended to broken and damaged accessories batteries and exposed antennas and to parts wearing out due to normal wear and tear Proper Delivery Returned products will not be accepted for warranty repair unless accompanied with a valid Return Merchandise Authorization RMA number issued by VCT RMA numbers issued by VCT ar
15. g components or parts VCT is not responsible for lost or damaged merchandise We strongly recommend insuring products for return shipping Return claims are void if manufacturer s seal is broken and or products are altered or modified subjected to an accident improper handling improper installation misuse and abuse or operated contrary to the operating instructions Products returned that are not in re saleable condition will be returned to customer at their expense Discontinued items special or custom made equipment items items not carried as stock even though they may appear on price lists may not be returned Returned products will be evaluated at the original purchase price and not at any subsequent price increase or decrease Subject to the conditions stated above the following re stocking fees will apply to products returned for credit refund VCT reserves the right to determine the validity of the product returned and or refuse to accept product for credit 0 Re Stocking Fee less original shipping charges If product is returned within 30 days from original VCT ship date 25 Re Stocking Fee less original shipping charges If product is returned within 60 days from original VCT ship date 50 Re Stocking Fee less original shipping charges If product is returned within 90 days from original VCT ship date 100 Re Stocking Fee 0 credit If product is returned after 90 days from original VCT ship date DISCLAIMER I
16. g link click here EN Close the browser Jl Audio L S Talkback Snapshot EJ Record PTZ Speed T TTT Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B LOGIN amp PASSWORD SET UP Changing the Video Encoders Login and Password is critical to the security of the device We strongly recommend that the Admin User Login and Password are changed once the device has been configured for network access The Admin User assignment will allow the Administrator Only to configure the device parameters The Common Users are able to view the video but not change or alter any system parameters Setting New Login amp Password Connect the IP Device to your workstation using supplied 3 ft network cable 2 Power the IP Device using the 12 VDC plug in adaptor Open IE Browser and enter the encoder default IP address Enter the default login and password Select the Settings Tab Select the Basic Parameters Tab a Select the User Management Section Enter your new login and password information into fields e Admin User Name e Admin User Password e Verify Mecsas os ais nel ees Click the OK button then Reboot the encoder WEE o to complete the process SE Channels Parameters Alarm Parameters Server slorage Restore to leave factory default parameters Syaber apliit Login 888888 Password 888888 ENCODER IP ADDRESS SET UP EE Connect the IP Devic
17. n no event will VCT or any of its affiliates be liable for any indirect special punitive consequential liability or incidental damages upon any basis of liability whatsoever even if advised of the possibility of such damages In addition VCT does not take any responsibility or assume any liability for the wiring installation or placement of the equipment Customer purchases or for the activities of any other individual or entity such as Customer s Company those who prepare the specifications or any local Authorities who inspect or approve Customer s installation 13 Copyright 2012 1156488 Ontario Inc 5 8GHz All Weather 8 Channel Series Manual Rev M VIDEYCOMM D TCAP A l IECUNOLOGIES gesktop seres This seres of network IP video encoders converts analog video ta allow for remote digital Di quality viewing sharing and recording locally or over the internat via laptop PC or SmartPhone Boasting many unique features including a remotely accessible embedded DVR this series is the perfect solution for monitoring and surveillance applications s Low Profile DeskTop Design e PTZ Ready Two Way Audio Motion Detection Masking 4 Alarm s High quality H 264 MJPEG D1 Resolution video e Embedded DVR for stand alone recording SD Card Sald Separately s NTSC 720 x 480 S0ips PAL 704 x 576 25fps e Outstanding free technical support and application design assistance Included 64 Gamera CMS Software SmartPhone Ready
18. s conflicts between devices on a network and allows you to manage them easily Assigning a Static IP address to your Windows PC or LAPTOP requires essentially the same process but the locations of the steps may vary between versions of Windows Using Windows XP ig Open Control Panel gt gt Select Network and Internet Connections 2 Select Network Connections gt gt Double Click Local Area Connection Highlight Internet Protocol TCP IP gt gt Click the Properties button O Now Change the IP Address to an available address gt gt Click OK when complete You MUST close out of the Network Connection Properties screen before the changes will take effect Using Windows 7 Gp Open Control Panel gt gt Select Network and Internet Connections E Select Network and Sharing Center gt gt Double Click Local Area Connection Select Properties gt gt Highlight Internet Protocol Version 4 TCP IP V4 gt gt click Properties button O Now Change the IP Address to an available address gt gt Click OK when complete Figure A You MUST close out of the Network Connection Properties screen before the changes will take effect Install Plug Download select the Click Here link to download the Install plug DOT AATE gt e S po gt 4 o jee EE ae IT WOU Street app As DLN WIELU OU COCA LUS UE YPU ai Run the Install plu
19. ur camera has an RCA connector e Connect the Video Encoder to your network using the standard network cable with a RJ 45 connector e A pre amplified speaker and microphone can be connected to provide two way audio if required Basic Set up The H 264 IP Video Encoder must be connected to a PC or Laptop for configuration The devices are compatible with most operating systems and Internet Explorer 6 0 browsers Setting a Static IP address on your PC or Laptop is essential for configuration prior to connecting the Video Encoder to the workstation Connect IP Device to your workstation using the supplied 3 network cable E Power the IP Device using the 12VDC Plug In Adaptor EH Open Internet Explorer browser and enter the default IP address 192 168 1 19 gt gt If no connection is made ensure that your workstations RJ 45 LAN connection is enabled See your computers Control Panel for more details Enter the Default Login 888888 amp Password 888888 tr video link click here 2 Works only with Internet Explore 6 0 WARNING Once Logged into the embedded web server through your internet browser the video screen may appear blank due to restrictions set on your workstation The video will NOT appear until the settings are configured through your operating system Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B PC STATIC IP ADDRESS Using Static IP addresses prevent
20. y unique features including a remotely accessible embedded DVR this series is the perfect solution for monitoring and surveillance applications ADVANTAGES e High quality H 264 MJPEG D1 Resolution video e NTSC 720 x 480 30fps PAL 704 x 576 25fps e Included 64 Camera CMS Software SmartPhone Ready e PTZ Ready Two Way Audio Motion Detection Masking amp Alarm e Embedded DVR for stand alone recording SD Card Sold Separately e Outstanding free technical support and application design assistance e Perfect for network access to remote locations for live or recorded video Copyright 2012 1156488 Ontario Inc IP Digital H 264 Video Encoder Series Manual Rev B PARTS LIST Please inspect the packaging carefully to ensure you have received all the necessary parts and accessories listed Refer to the following chart to determine which parts are included with your product If any parts are missing or damaged contact VideoComm Technologies Customer Service or your re seller immediately KIT INCLUDES All Weather IP Video Encoder Server DeskTop IP Video Encoder Server OEM IP Video Encoder Server R45 3 Network Setup Cable RS483 amp Abr Input Connector RS485 Termination Resistor Embedded Video Viewinz Recording Software Professional 64 Camera NYRER Software CD ROM 20H Rubber Duck 3G Antenna 20H Rubber Duck WiFi Antenna Power Supply PS 1210LX Power Supply PS 121 DC Power Jack A
Download Pdf Manuals
Related Search