Owner`s Manual
Contents
1. Janaka TBC 255SFK OWNER S MANUAL Read the manual carefully before operating this machine EN SP PA INTRODUCTION Thank you for your purchase of the Tanaka 3 in 1 professional yard maintenance kit The easy quick connect design allows you to efficiently switch between the various tools for different jobs and one commercial quality engine powers all of the equipment Please take the time to carefully review all of the information accompanying your new equipment A complete understanding of the product and its uses will make for a more enjoyable and productive experience Power equipment can be dangerous Use good judgment when operating the tools and most importantly read and understand all of the safety precautions prior to operating Be sure that anyone else who may be operating this equipment has received and reviewed the manual An exploded parts illustration is available on the Tanaka website www tanakapowerequipment com Always use genuine Tanaka replacement parts and accessories If you have any questions as to the function or safety of the equipment seek professional guidance either from your Tanaka dealer or from Tanaka direct at 1 888 482 6252 or www tanakapowerequipment com In addition to the attachments included with your TBC 255SFK the following attachments and accessories can be purchased to add to its versatility TMC 200 Mini cultivator Attachment TSW 210 Power Sweeper Attachment TPH 210 Arti2. N CAUTION PROPER TENSION IS EXTREMELY IMPORTANT Raise the bar end and securely tighten the chain bar clamp nut with the Supplied box wrench A new chain will stretch so adjust the chain after a few cuts and watch chain tension carefully for the first half hour of cutting N CAUTION Always wear gloves when touching the chain TBC 255SFK 14 Owner s Manual 5 UNIT ASSEMBLY amp OPERATION Polesaw Attachment Chain Oil The chain oiler on your pole saw is automatic When the engine is running the chain oil is automatically discharged Fill oil reservoir with good quality bar and chain oil Remove the oil reservoir tank cap 1 and fill to the top Add chain oil when its level lowers to one centimeter from bottom Adjustment of Chain Oil Suppl Loosen the locking screw 2 one turn Turn the adjusting screw 3 clockwise to decrease the quantity and turn it counterclockwise to increase the quantity Do not turn the adjusting screw 3 clockwise beyond one turn from its most counterclockwise position or the maximum quantity discharged position After adjustment has been made tighten locking screw 2 Pole Saw Pruning Techniques This attachment is designed for trimming small limbs and branches up to 8 in diameter Follow these tips for successful operation 1 Plan cut carefully Check to see direction branch will fall before beginning 2 Long branches should be removed in several pieces 3 Do not stand dire
3. KOGYO CO LTD SERVICE CENTER AS SOON AS A PROBLEM EXISTS THE WARRANTY REPAIRS SHOULD BE COMPLETED IN A REASONABLE AMOUNT OF TIME NOT TO EXCEED 30 DAYS IF YOU HAVE ANY QUESTIONS REGARDING YOUR WARRANTY RIGHTS AND RESPONSIBILITIES YOU SHOULD CONTACT TANAKA KOGYO CO LTD C O INTERNATIONAL SALES amp MARKETING INC CUSTOMER SERVICE REPRESENTATIVE AT 253 3331200 TBC 255SFK 21 Owner s Manual 8 SPECIFICATIONS Model TBC 255SFK EN 24 1 46 cu in Spark 1 Champion CJ6Y or RCJ6Y or equivalent i 0 67 22 8 fl oz 5 4 11 9 Ibs K Sound Pressure Level dB A 92 5 Sound Power Level dB A 112 TBC 255SFK 22 Owner s Manual
4. THE ORIGINAL DELIVER DATE LIABILITIES OF INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES ARE EXCLUDED SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST AUTHORIZED SERVICE DEALER PLEASE CALL TANAKA KOGYO CO LTD C O INTERNATIONAL SALES amp MARKETING INC 253 3331200 IMPORTANT YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE PLEASE FILL OUT THE CARD AND SEND IT TO TANAKA AMERICA 1028 Am STREET SOUTH WEST AUBURN WA 98001 BE SURE TO KEEP A COPY FOR YOUR RECORDS TBC 255SFK 20 Owner s Manual EN 7 WARRANTY EPA PHASE2 CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT EN EPA THE CALIFORNIA AIR RESOURCES BOARD AND TANAKA KOGYO CO LTD ARE PLEASED TO EXPLAIN THE EXHAUST AND EVAPORATIVE EMISSION CONTROL SYSTEM WARRANTY ON YOUR TANAKA SMALL OFF ROAD ENGINE NEW SMALL OFF ROAD ENGINES MUST BE DESIGNED BUILT AND EQUIPPED TO MEET STRINGENT EPA PHASE2 CALI FORNI A ANTI SMOG STANDARDS TANAKA KOGYO CO LTD MUST WARRANT THE EMISSION CONTROL SYSTEM ON YOUR SMALL OFF ROAD ENGINE FOR THE PERIODS OF TIME LISTED BELOW PROVIDED THERE HAS BEEN NO ABUSE NEGLECT OR IMPROPER MAINTENANCE OF SMAL
5. With all the washers in place over the end of the shaft Ki Se fiber place the connector over the shaft end with the E washers so the locator bolt 1 on the connector is warher aligned with the locator hole on the shaft After the locator bolt is secured tighten the connector to the shaft using the pinch bolt 2 large copper washer With the connector assembled to the upper shaft you can now attach the lower shaft assembly as described in the next section 4 The lower bruschutter section comes with the No Brainer cutting head attached Place the opposite end of the shaft into the coupler on the upper shaft as depicted 5 Make sure the shaft is fully inserted and that the locking bolt is properly aligned with the location hole and that the tightening knob is securely tightened Failure to properly connect the shaft sections will result in damage to the shaft and possible injury to the operator 6 Install the safety guard onto the shaft as shown Use caution when handling the safety guard as the shield uses a sharp line limiter blade CAUTION Your TBC 255SFK is categorized under the ANSI safety standard B175 3 as a convertible grass trimmer This means that while your machine does not come equipped as blade capable it is possible to convert it for use with a steel blade commonly referred to as a brushcutter By purchasing the blade kit Tanaka part number 748503 you will have the necessary comp
6. any wires power telephone cable etc are closer than 15M 50ft to any part of the operator or unit N AVOID ALL POWER LINES THIS UNIT IS NOT INSULATED AGAINST ELECTRICAL CURRENT Spectators and fellow workers must be warned and children and animals prevented from coming nearer than 15M 50ft while pole saw is in use Always wear head protection with full face shield to help protect against falling branches or debris TBC 255SFK 13 Owner s Manual 5 UNIT ASSEMBLY amp OPERATION Polesaw Attachment Pole Saw Operation Installation of bar and chain Install the chain guide bar 1 onto the bolt 2 then push it toward the sprocket 3 as far as it will go Make sure the boss of the chain tension adjuster 4 fits into the hole of the bar 5 NOTE Slightly move the bar back and forth and make sure the chain tension boss 4 fits into the hole 5 in the bar properly Confirm the direction of saw chain 1 is correct as indicated and align the chain on the sprocket Guide the chain drive links into the bar groove all the way around the bar Install the side case 2 onto the guide bar clamp bolt Thread nut onto clamp bolt but only tighten by hand Raise the bar end and tighten the chain 1 by turning the tension adjustment bolt 2 clockwise To check proper tension lightly lift up the center of the chain and there should be about 0 5 1 0 mm clearance between bar and edge of drive link 3
7. recommended procedures Disconnect the spark plug before performing maintenance except for carburetor adjustments Keep others away when making carburetor adjustments Use only genuine Tanaka replacement parts as recommended by the manufacturer N transport and safety Carry the unit machine by hand with the engine stopped and the muffler away from your body Allow the engine to cool empty the fuel tank and secure the unit machine before storing or transporting in a vehicle Store unit machine out of the reach of children Clean and maintan the unit carefully and store it in a dry place Make sure engine switch is off when transporting or storing Owner s Manual EN 4 GENERAL UNIT OPERATION Fuel WARNING The trimmer is equipped with a two stroke engine Always run the engine on fuel which is mixed with oil Provide good ventilation when fueling or handling fuel Always use branded 89 octane unleaded gasoline Use Tanaka two cycle oil with a mix of 50 1 If Tanaka oil is not available use an anti oxidant added quality oil expressly labeled for air cooled 2 cycle engine use JASO FC GRADE OIL or ISO EGC GRADE Do not use BIA or TCW 2 stroke liquid cooled type mixed oil Never use multi grade oil 10 W 30 or waste oil Always mix fuel and oil in a seperate clean container Always start by filling half the amount of fuel which is to be used Then add the whole am
8. when the engine runs smoothly in all positions well below the rom when the cutting attachment starts to rotate If the cutting attachment still rotates after idle speed adjustment contact your Tanaka dealer NOTE Standard Idle rom is 2500 3000 rpm WARNING When the engine is idling the cutting attachment must under no circumstances rotate Air filter The air filter must be cleaned from dust and dirt in order to avoid e Carburetor malfunctions e Starting problems e Engine power reduction e Unnecessary wear on the engine parts e Abnormal fuel consumption Clean the air filter daily or more often if working in exceptionally dusty areas Cleaning the air filter Remove the air filter cover and the filter 1 Rinse it in warm soap suds Check that the filter is dry before reassembly An air filter that has been used for some time cannot be cleaned completely Therefore it must regularly be replaced with a new one A damaged filter must always be replaced TBC 255SFK 16 Owner s Manual EN 6 MAINTENANCE Brush Cutter Fuel Filter Drain all fuel from fuel tank and pull fuel filter line from tank Pull filter element out of holder assembly Replace filter if it appears to be discolored or hardened from use The filter has a white felt like appearance when new Spark Plug The spark plug condition is influenced by e An incorrect carburetor setting e Wrong fuel mixture too much oil in the gasoline e A dirty ai
9. 00 rom Extended time of use at low rom may wear out the clutch prematurely Cut grass from right to left If using a steel blade thrust may occur when the spinning blade contacts a solid object in the critical area A dangerous reaction may occur causing the entire unit and operator to be thrust violently This reaction is called BLADE THRUST As a result the operator may lose control of the unit which may cause serious or fatal injury Blade thrust is more likely to occur in areas where it is difficult to see the material to be cut A The blade turns counterclockwise therefore be advised to operate the unit from right to left for efficient cutting 2 Keep onlookers out of working area at least 15m 50 ft WARNING If cutting attachment should strike against stones or other debris stop the engine and make sure that the attachment and related parts are undamaged When grass or vines wrap around attachment stop engine and attachment and remove them Stopping Decrease engine speed and run at an idle for a few minutes then turn off ignition switch N WARNING A cutting attachment can injure while it continues to spin after the engine is stopped or power control is released When the unit is turned off make sure the cutting attachment has stopped before the unit is set down TBC 255SFK 11 Owner s Manual 5 UNIT ASSEMBLY amp OPERATION Edger Attachment Edger Assembly The edger attachment comes asse
10. CO LTD SMALL OFF ROAD ENGI NE TWOYEAR LI MI TED WARRANTY EMISSION RELATED PARTS FOR TWO YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE SMALL OFF ROAD ENGINE TANAKA THE COMPANY THROUGH ANY TANAKA DEALER WILL REPAIR OR REPLACE FREE OF CHARGE FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND OR WORKMANSHIP EMISSIONRELATED PARTS ARE THE CARBURETOR ASS Y GNITIONCOIL ASS Y MAGNETOROTOR SPARKPLUG WIRES SPARKPLUG FUEL TANK FUELFILTERS AI RFILTERS FUELPIPE CATALYTIC MUFFLER ON APPLICABLE MODELS AND ALL GASKETS HOWEVER SPARKPLUGS AIRFILTER FUELFILTER ARE WARRANTED TILL THE FIRST REPLACEMENT POINT ALL OTHER PARTS EXCEPT ABOVE PARTS FOR TWO YEARS OF HOME USE ONE YEAR FOR ANY OTHER USE FROM THE DATE OF ORIGINAL DELIVERY OF THE SMALL OFF ROAD ENGINE TANAKA THE COMPANY THROUGH ANY TANAKA DEALER WILL REPAIR OR REPLACE FREE OF CHARGE FOR THE ORIGINAL PURCHASER ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND OR WORKMANSHIP THIS 15 THE EXCLUSIVE REMEDY THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE TANAKA DEALER THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION THAT A WARRANTY PART 15 DEFECTIVE IF THE DIAGNOSTIC WORK IS PERFORMED AT THE TANAKA DEALER THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE AS DEFINED BY THE MANUFACTURER IN THE OWNNER S MANUAL AN
11. L OFF ROAD ENGINE YOUR EMISSION CONTROL SYSTEM INCLUDES PARTS SUCH AS THE CARBURETOR FUEL TANK IGNITION SYSTEM AND CATALYTIC CONVERTER WHERE A WARRANTABLE CONDITION EXISTS TANAKA KOGYO CO LTD WILL REPAIR YOUR SMALL OFF ROAD ENGINE AT NO COST TO YOU INCLUDING DIAGNOSIS PARTS AND LABOR ANY SUCH PART REPAIRED OR REPLACED UNDER WARRANTY WILL BE WARRANTED FOR THE REMAINDER OF THE PERIOD PRIOR TO THE FIRST SCHEDULED REPLACEMENT POINT FOR THE PART MANUFACTURE S WARRANTY COVERAGE THE 1995 AND LATER SMALL OFF ROAD ENGINES ARE WARRANTED FOR TWO YEARS IF ANY EMISSION RELATED PART ON YOUR ENGINE IS DEFECTIVE THE PART WILL BE REPAIRED OR REPLACED BY TANAKA KOGYO CO LTD OWNER S WARRANTY RESPONSI BI LI TI ES AS THE SMALL OFF ROAD ENGI NE OWNER YOU ARE RESPONSI BLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE LISTED IN YOUR OWNER S MANUAL TANAKA KOGYO CO LTD RECOMMENDS THAT YOU RETAIN ALL RECEIPTS COVERI NG MAINTENANCE ON YOUR SMALL OFF ROAD ENGINE BUT TANAKA KOGYO CO LTD CANNOT DENY WARRANTY SOLELY FOR THE LACK OF RECEIPTS OR FOR YOUR FAILURE TO ENSURE THE PERFORMANCE OF ALL SCHEDULED MAINTENANCE AS THE SMALL OFF ROAD ENGINE OWNER YOU SHOULD BE AWARE HOWEVER THAT TANAKA KOGYO CO LTD MAY DENY YOU WARRANTY COVERAGE IF YOUR SMALL OFF ROAD ENGINE OR A PART HAS FAILED DUE TO ABUSE NEGLECT IMPROPER MAINTENANCE OR UNAPPROVED MODIFICATIONS YOU ARE RESPONSIBLE FOR PRESENTING YOUR LAWN AND GARDEN EQUIPMENT ENGINE TO A TANAKA
12. SFK 5 Owner s Manual 2 FEATURES AND COMPONENTS Fuel Cap Throttle Trigger Starter Handle Blade Guard Cutting attachment Drive Shaft Tube Handle Bar Ignition switch Throttle lock 10 Safety Trigger 11 Choke lever 12 Engine 13 Angle transmission 14 Joint Case A TBC 255SFK 6 Owner s Manual 3 WARNINGS AND SAFETY INSTRUCTIONS If situations occur which are not covered in this manual take care and use common sense Contact your dealer if you need assistance Pay special attention to statements preceded by the following words N WARNING Indicates a strong possibility of severe personal injury or loss of life if instructions are not followed NOTE Helpful information for correct function and use N CAUTION Indicates a possibility of personal injury or equipment damage if instructions are not followed N CAUTION Do not disassemble the recoil starter You may get a possibility of personal injury with recoil spring N operator Safety Always wear a safety face shield or goggles Always wear heavy long pants boots and gloves Do not wear loose clothing jewelry short pants sandals or go barefoot Secure hair so it is above shoulder length Do not operate this tool when you are tired ill or under the influence of alcohol drugs or medication Never let a child or inexperienced person operate the machine Wear heari
13. Y WARRANTED PART WHICH 15 NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE OR WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF REPAIR OR REPLACE AS NECESSARY SHALL BE WARRANTED FOR THE WARRANTY PERIOD ANY WARRANTED PART THAT 15 SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE FOR THE PERIOD OF TIME UP TO THE FIRST SCHEDULED REPLACEMENT POINT FOR THAT PART ANY SUCH PART REPAIRED OR REPLACED UNDER WARRANTY WILL BE WARRANTED FOR THE REMAINDER OF THE PERIOD PRIOR TO THE FIRST SCHEDULED REPLACEMENT POINT FOR THE PART ANY REPLACEMENT PART THAT 15 EQUIVALENT IN PERFORMANCE AND DURABILITY MAY BE USED IN NONWARRANTY MAINTENANCE OR REPAIRS AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE COMPANY THE COMPANY 15 LIABLE FOR DAMAGES TO OTHER ENGI NE COMPONENTS CAUSED BY THE FAILURE OF A WARRANTED PART STILL UNDER WARRANTY THIS WARRANTY DOES NOT APPLY THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF INSTRUCTION LISTED IN THE OWNER S MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS ACCIDENT MISHANDLING ALTERATION ABUSE IMPROPER LUBRICATION USE OF ANY PARTS OR ACCESSORIES OTHER THAN THOSE SPECIFIED BY THE COMPANY OR OTHER CAUSES BEYOND THE COMPANY S CONTROL THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGE IN THEIR APPEARANCE THERE ARE NO OTHER EXPRESS WARRANTIES IMPLI ED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LISTED TO TWO YEAR FROM
14. ain oiler port 1 and bar groove Check gear case for grease level about every 50 hours of operation by removing the grease filler plug on the side of the gear case TBC 255SFK 18 Owner s Manual 6 MAINTENANCE General Below you will find some general maintenance instructions Maintenance schedule For further information please contact your service dealer Daily maintenance Clean the exterior of the unit Check that the harness is undamaged Check the blade guard for damage or cracks Change the guard in case of impacts or cracks Make sure the cutting attachment is properly centered sharp and without cracks An off centered cutting attachment induces heavy vibrations that may damage the unit Make sure the cutting attachment nut is sufficiently tightened Make sure the blade transport guard is undamaged and that it can be securely fastened Check that nuts and screws are sufficiently tightened Weekly maintenance Check the starter especially cord and return spring Clean the exterior of the spark plug Remove it and check the electrode gap Adjust it to 0 6 mm or change the spark plug Clean the cooling fins on the cylinder and make sure the air intake at the starter is not clogged Make sure the gear case is filled with grease up to full Clean the air filter Monthly maintenance Clean the exterior of the carburetor and the space around tt TBC 255SFK 19 Owner s Manual 7 WARRANTY TANAKA KOGYO
15. ctly beneath branch being cut 4 Look out for branch immediately behind the branch being cut If pole saw impacts rear branch damage to the machine can occur 5 Apply plenty of throttle to avoid chain catching in the wood 6 When pruning a limb of 4 in diameter or larger cut as follows a Undercut limb diameter near tree trunk b Finish top cut slightly farther out on limb c Flush cut stub at trunk 7 Never use the pole saw for bucking or felling TBC 255SFK 15 Owner s Manual EN 6 MAINTENANCE Brush Cutter Carburetor adjustment N WARNING The cutting attachment may be spinning during carburetor adjustments WARNING Never start the engine without the complete clutch cover and tube assembled Otherwise the clutch can come loose and cause personal injuries In the carburetor fuel is mixed with air When the engine is test run at the factory the carburetor is basically adjusted A further adjustment may be required according to climate and altitude The carburetor has one adjustment possibility T Idle speed adjustment screw Idle speed adjustment T Check that the air filter is clean When the idle speed is correct the cutting attachment will not rotate If adjustment is required close clockwise the T screw with the engine running until the cutting attachment starts to rotate Open counter clockwise the screw until the cutting attachment stops You have reached the correct idle speed
16. culating Pole Hedge Trimmer Attachment 2 and 3 Pole Saw Extensions s ER os teat Fn Y TBC 255SFK 2 Owner s Manual EN IMPORTANT SAFETY INFORMATION WARNING e Read the Operator s Manual and follow all warnings and safety instructions Failure to do so result in serious injury to the operator and Jor bystanders e Objects may be thrown or ricochet in all directions ALWAYS WEAR EYE PROTECTION e Keep bystanders at least 50 feet 15m away e To reduce the chance of hearing loss always wear ear protection e To reduce the risk of injury from loss of control never use a metal blade on a curved shaft grass trimmer Never use a metal blade on any brushcutter without barrier bar or bicycle handle configuration and safety strap e Use of a blade may cause a sudden sideways forward or backward motion of the brushcutter when the blade contacts a solid object See Owner s manual for model specific details Before using your new unit Js WARN NG Read the operators manual carefully Check that the cutting equipment is correctly The engine exhaust from this product assembled and adjusted contains chemicals known to the State Start the unit and check the carburetor adjustment of California to cause cancer birth See Mainentenace defects and other reproductive harm eaninas of symbols or labels an It is important that you read fully understand and observe the following safety pr
17. ecautions and Read understand and follow all warnings Careless or improper use of the unit warnings and instructions in this may cause serious or fatal injury manual and on the unit Always wear eye head and ear Gloves should be worn when Use anti slip and sturdy protectors when using this unit necessary e g when assem footwear bling cutting equipment TBC 255SFK 3 Owner s Manual EN TABLE OF CONTENTS 1 Carton Contents ccccceceeeeeece eee eaees 5 2 Key Features and Commponemts 6 3 Warnings and Safety Instructions 7 4 General Operation 0 ccceeeeeseseeeseeees 8 5 Unit Assembly amp Operation Brush Cutter 9 11 Edger Attachment 12 Polesaw Attachment 13 15 6 Maintenance ccc ccc ee cece eee eeeaeeeeeeees Brush Cutter 16 17 Edger Attachment 18 Polesaw Attachment 18 Maintenance Gchecdule naa aeaaea 19 VV All ln TE 20 21 8 Specifications cc eee ce cece ee eee eee e eee eee es 22 TBC 255SFK 4 Owner s Manual 1 CARTON CONTENTS 1 Engine 5 Edger Attachment 2 Joint Case Assembly 6 Edger Wheel Assembly not attached in box 3 Trimmer Attachment 7 Pole Saw shaft 4 Safety Guard not attached in box 8 Pole Saw Assembly not attached in box OO 1 Joint Case Assembly 2 Safety Guard Assembly 3 Nylon Line 4 2 6 oz bottle of Tanaka Oil 4 5 5 Edger Blade spare 6 Strap TBC 255
18. fore starting engine Stop engine before removing fuel cap Empty the fuel tank before storing the unit machine It is recommended that the fuel be emptied after each Use WARNING Antivibration systems do not guarantee that you will not sustain whitefinger disease or carpal tunnel syndrome Therefore continual and regular users should monitor closely the condition of their hands and fingers If any of the above symptoms appear seek medical advice immediately N cutting Safety Do not cut any material other than grass and brush Inspect the area to be cut before each use Remove objects which can be thrown or become entangled For respiratory protection wear an aerosol protection mask when cutting the grass after insecticide is scattered Keep others including children animals bystanders and helpers outside the 15 m hazard zone Stop the engine immediately if you are approached Always keep the engine on the right side of your body Hold the unit machine firmly with both hands Keep firm footing and balance Do not over reach 7 Keep all parts of your body away from the muffler and cutting attachment when the engine is running Keep cutting attachment below waist level Store unit machine and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters electric motors or switches furnaces etc Maintenance safety Maintain the unit machine according to
19. g blade WARNING If blade should strike against stones or other debris stop the engine and visually inspect the blade guard and related parts for any damage TBC 255SFK 12 Owner s Manual 5 UNIT ASSEMBLY amp OPERATION Polesaw Attachment Pole Saw Assembly EN The pole saw attachment requires that the gear case be mounted to the shaft The shaft is marked with SF PS One end of the inner shaft is splined while the other end is square As with all of the attachments the square end is designed to fit into the shaft coupler The splined end is where the gear case mounts Loosen the locator screw 1 and set screw 3 Insert the shaft tube into the gear case Because the splines may not immediately align it requires the shaft to be rotated until the splines align and the shaft seats in the gear case When properly installed the decal indicating proper assembly will appear as indicated Pole Saw Operation Before proceeding with this section BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL WARN INGS AND SAFETY INSTRUCTIONS DESCRIBED IN SECTION 3 WARNING J DANGER All overhead electrical conductors and communications wires can have electricity flow with high voltages Never touch wires directly or indirectly when trimming otherwise serious injury or death may result N CAUTION Review the area to be trimmed Look for hazards that could contribute to unsafe conditions DO NOT operate unit if
20. ion by removing the grease filler plug on the side of the case If no grease can be seen on the flanks of the gears fill the transmission with a quality lithium based multipurpose grease up to 3 4 Do not completely fill the transmission TBC 255SFK 17 Owner s Manual 6 MAINTENANCE Edger Maintenance Edger Polesaw Attachments Blade WARNING Wear protective gloves when handling or performing maintenance on the blade When replacing blade use genuine Tanaka replacement blade with a one inch 25 4mm center arbor hole Discard blades that are bent cracked warped broken or damaged in any way Gear Case Check gear case for grease level after every 50 hours of use Remove the grease filler plug on the side of the gear case If no grease can be seen on the flanks of the gears fill with a quality lithium based multipurpose grease Fill to about do not completely fill Edger Blade Replacement 1 Take off the left handed nut 1 and cutter holder cap 2 from the blade shaft 2 Install blade on the shaft and then replace the cutter holder and nut in order NOTE When installing cutter holder cap 2 be sure to set concave side facing blade 3 Insert the locking bar 4 into the hole of the cutter holder 5 and the gear case by lining up each hole 4 Tighten the blade nut securely clockwise to loosen counter clockwise to tighten Pole Saw Maintenance Before each use clean the ch
21. mbled with the exception of attaching the wheel to the blade guard assembly Using the carriage bolt included with the wheel attach to the blade guard bracket as shown By loosening the safety guard assembly bolts shown as reference number 3 the angle of the guard can be adjusted for preference Be sure that the guard does not come off of the gear case lip on which it is intended to ride Attempting to tighten it in place when incorrectly positioned can cause damage Edger Operating Procedures Before proceeding with this section BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL WARNINGS AND SAFETY INSTRUCTIONS DESCRIBED IN SECTION 3 Use only for edging the type of grass and other growth for which the machine is designed 1 Adjust the wheel within the guard bracket as depicted Adjust cutting depth by loosening knob nut 1 and moving location of wheel up or down To increase cutting depth move wheel location upwards and to decrease move it lower After the location is decided tighten knob nut 1 securely NOTE All adjustments should be made after engine has stopped completely stop switch is in the OFF position and cutting attachment has stopped turning 2 Always hold unit firmly with both hands and keep body well balanced 3 Always operate the edger positioned with the engine on the right side of the operator WARNING Operate the unit from a position where guard blocks the line of sight to the cuttin
22. ng protection Never start or run the engine inside a closed room or building Breathing exhaust fumes can kill Keep handles free of oil and fuel Keep hands away from cutting equipment Do not grab or hold the unit by the cutting equipment When the unit is turned off make sure the cutting attachment has stopped before the unit is set down When operation is prolonged take a break from time to time so that you may avoid possible whitefinger disease which is caused by vibration A unit Machine Safety Inspect the entire unit machine before each use Replace damaged parts Check for fuel leaks and make sure all fasteners are in place and securely tightened TBC 255SFK Replace parts that are cracked chipped or damaged in any way before using the unit machine Make sure the safety guard is properly attached Keep others away when making carburetor adjustments Use only accessories as recommended for this unit machine by the manufacturer N WARNING Never modify the unit machine in any way Do not use your unit machine for any job except that for which it is intended A N Fuel Safety Mix and pour fuel outdoors and where there are no sparks or flames Use a container approved for fuel Do not smoke or allow smoking near fuel or the unit machine or while using the unit machine Wipe up all fuel spills before starting engine Move at least 3 m away from fueling site be
23. onents to safely use a blade These components include a blade capable debris shield barrier bar safety strap and blade retaining hardware NEVER ATTEMPT TO USE THIS MACHINE WITH A STEEL BLADE WITHOUT FIRST PROPERLY CONVERTING THE UNIT TO A BLADE CAPABLE BRUSHCUTTER TBC 255SFK 9 Owner s Manual EN 5 UNIT ASSEMBLY amp OPERATION Brush Cutter Line Trimmer Operation BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL WARNINGS AND SAFETY INSTRUCTIONS DESCRIBED IN SECTION 3 Cutting Safety a b C D roapos Starting caution Before starting make sure the cutting attachment does not touch anything 1 Set ignition switch 1 to ON postion Push priming bulb 4 several times so that the fuel flows through return pipe 2 Set choke lever to CLOSED position 5 3 Pull recoil starter briskly taking care to keep the handle in your grasp and not allowing it to snap back 4 When you hear the engine want to start return choke lever to RUN position open Then pull recoil starter briskly again NOTE If the engine does not start repeat procedures from 2 to 4 Do not cut any material other than grass and brush Inspect the area to be cut before each use Remove any objects which can be thrown or can become entangled For respiratory protection wear an aerosol protection mask especially if any insecticide or other chemical agents have been dispersed Always wear a Safety face shield or goggle
24. ount of oil Mix shake the fuel mixture Add the remaining amount of fuel Mix shake the fuel mix thoroughly before filling the fuel tank Fueling WARNING Always shut off the engine before refueling Slowly open the fuel tank when filling up with fuel so that possible over pressure disappears Tighten the fuel cap carefully after fueling Always move trimmer at least 3m 1 Oft from the fueling area before starting Before fueling clean the tank cap area carefully to ensure that no dirt falls into the tank Make sure that the fuel is well mixed by shaking the container before fueling TBC 255SFK 8 Owner s Manual 5 UNIT ASSEMBLY amp OPERATION Brush Cutter Power Head Assembly The TBC 255SFK utilizes one engine to power all of the various attachments The top portion of the shaft closest to the engine is common to all of the attachments The brushcutter shaft lower portion requires set up as follows 1 1 Remove all of the product contents from the carton Identify the engine with the shaft and handle attached as shown 2 Locate the lower section of brushcutter shaft as shown de 3 Before the lower shaft assembly can be joined to the upper shaft it is necessary to install the coupler onto 1 locator bolt the upper shaft Carefully place all three washers over Nee the end of the shaft protruding fro m the shaft Q 2 pinch bolt to shaft assembly on the engine side as depicted 0
25. r filter e Difficult running conditions such as cold weather These factors cause deposits on the spark plug electrodes which may result in malfunction and starting difficulties If the engine is low on power difficult to start or runs poorly at idling speed always check the spark plug first If the spark plug is dirty clean it and check the electrode gap Readjust if necessary The correct gap is 0 6 mm The spark plug should be replaced after about 100 operation hours or earlier if the electrode is badly eroded NOTE In some areas local law requires using a resistor spark plug to Suppress ignition signals If this machine was originally equipped with resistor spark plug use the same type of spark plug for replacement Muffler Remove the muffler and clean any excess carbon from the exhaust port or muffler inlet every 100 hours of operation Cylinder Engine cooling The engine is air cooled and air must circulate freely around engine and over cooling fins on cylinder head to prevent overheating Every 100 Operating hours or once a year more often if conditions require clean fins and external surfaces of engine of dust dirt and oil deposits which can contribute to improper cooling NOTE Do not operate engine with engine shroud or muffler guard removed as this will cause overheating and engine damage Angle transmission brushcutter and edger only Check the gear case grease level about every 50 hours of operat
26. s Always wear heavy long pants boots and gloves Do not wear loose clothes jewelry short pants sandals or go barefoot Secure hair so it is above shoulder length Do not operate the tool if you are tired ill or under the influence of alcohol drugs or medication Never let a child or inexperienced person operate the machine Never start or run the engine inside an enclosed room or building Exhaust fumes can kill Keep handles free of oil and dirt Keep hands away from cutting attachments When the unit is turned off make sure the cutting attachment has stopped before the unit is set down When operation is prolonged take a break form time to time so that you may avoid possible white finger disease which is caused by vibration Wear hearing protection Keep all others bystanders including children and pets outside the 15 meter hazard zone Stop the engine immediately if you are approached Always keep the engine on the right side of your body Hold the machine firmly with both hands Keep all parts of your body away from the muffler and cutting attachment when the engine Is running Keep firm footing and balance Do not over reach Keep cutting attachment below waist level 5 After starting engine allow engine about 2 3 minutes to warm up before subjecting it to any load TBC 255SFK 10 Owner s Manual EN 5 UNIT ASSEMBLY amp OPERATION Brush Cutter Cutting When cutting operate engine at over 65
Download Pdf Manuals
Related Search