User`s Manual
Contents
1. FE F3 i Connect to ARS 2033N IDE port Connect to IDE Connect to IDE hard DVD ROM drive drive Master Slave 2 Two connectors for DVD writers Connect to ARS 2033N IDE port Connect to IDE Writer 21 2033N User s Manual Chapter 4 Functions There are 13 major functions in the copy controller and there are subfunctions in Function 9 10 11 and 13 as the following figures show 1 Copy 2 Test 3 Test amp Copy 4 Verify 5 Compare 6 Prescan Copy Controller 7 Disc Info 8 Select Source 9 Image 10 Edit Track 11 Setup 12 Link Select 13 Advanced Setup 22 In Function 9 there are 8 subfunctions 2033N User s Manual 9 1 Load 9 2 Delete Image 9 3 Image Info 9 Image 9 4 Compare Image 9 5 Select Image 9 6 Image Src Drive 9 7 Image Format Info In Function 10 there are 4 subfunctions 10 Edit Track 9 8 Edit 10 1 CD to CD 10 2 CD to HDD 10 3 Play Audio Track 23 10 4 Close Session 2033N User s Manual In Function 11 t2. The hard disk is verified successfully Verify Partition Header esses Verify the partition header 3 Audio Editing Burn or Move to partition Do you want to directly copy the data into disc or move them to the partition Can t edit HDD The hard disk cannot be edited as a source audio disc Close all disc s session Confirm the closing of disc sessions Continue edit next Disc Ask if you want to continue the music disc editing End edit disc and burn Finish the music disc editing and start to copy Erase selected Tracks Abort the selected tracks and delete them Ins empty disc Continue Do you want to insert a blank disc and continue copying Insertnext disc eee Reps Insert the next audio disc NO AUDIO track in this disc The source disc has no audio track Sessions were closed already The disc sessions have already been closed Target Overflow Re Select The disc capacity is not enough to store the selected tracks Please select again Tgt overflow del last trk The disc capacity is not enough to store the selected tracks So do you want to delete the last track 4 Firmware Update Check Sum Error eee The udpated firmware has errors Flash ROM fail
3. sss Data cannot be written into Flash ROM Invalid firmware The disc doesn t contain a valid firmware Last update F W Fail The firmware is not updated successfully Last update F W OK sss The firmware is updated successfully Searching F W sss The system is searching for a valid firmware Source can t be Hard Disk During comparison the source cannot be hard disk 89 2033N User s Manual Update F W xxx to yyy Do you want to update the firmware version from xxx to yyy Updating F W eee The system is updating the firmware 90 2033N User s Manual Technical Support Form Email support acard com http www acard com Model ARS 2033N Channel F W Version DVD ROM DVD Writer Hard Disk Model type Capacity Firmware version Others Problem Description 91
4. 55 2033N User s Manual 4 11 5 Auto Start Drive Now press ESC and to see the following figure Auto Start Drive is to copy or test automatically once you put blank DVDs into the writers 11 05 Setup Auto Start Drive Press ENT to see the following figure The default is Off Press W to select 1 one blank DVD Auto Start Drive Off 4 11 6 Startup Menu Now press ESC and V to see the following figure Startup Menu lets you select any one of the functions except Adv Setup as the first item appearing on the menu whenever you turn on the copy controller 11 06 Setup Startup Menu 56 2033N User s Manual Press ENT to see the following figure The default is Copy You can certainly select any other function as the first item but remember to press ENT to confirm Startup Menu 1 Copy 4 11 7 Auto Verify Now press ESC and WV to see the following figure Auto Verify is to verify automatically if the target DVDs can be read after copying 11 07 Setup Auto Verify Press ENT to see the following figure The default is Off Auto Verify Off You can press W to select On Auto Verify On 57 2033N User s Manual 4 11 8 Auto Compare Now press ESC and to see the following figure Auto Compare is to compare automatically the source DVD and the target DVDs after copying 11 08 Setup Auto Compare Press ENT to see the following figure The default is Off P
5. Press ENT to see the next figure Test is simply a simulation Burn in Test Press ENT and use A V to select the time of simulation such as 1 2 3 1000 or Run Continuous The figure below shows Run Continuous Sel burn in num Run Continuous Press ESC ENT V to select Erase amp Copy as the following figure shows Erase amp Copy is to erase and write repeatedly It is only for DVD rewriteable discs Burn in Erase amp Copy 72 2033N User s Manual Press ENT and use A V to select the time of simulation such as 1 2 3 1000 or Run Continuous The figure below shows Run Continuous Sel burn in num Run Continuous 4 13 7 Update Firmware Now press ESC and V to see the following figure Update Firmware is to update the firmware to the latest version But you should get the version first 13 07 Adv Setup Update Firmware You can get the newest version from ACARD by e mail or download it directly from the Web site http www acard com Then unzip the file of zip and copy it into a CD RW If the file is bin you don t need to unzip After placing the DVD into the DVD ROM press ENT The system will begin searching the new firmware and show the message on LCD as follows after it finds the new firmware Then press ENT to update Searching F W XXX XXXXX 73 2033N User s Manual 4 13 8 Compare Firmware Now press ESC and V to see the following figure Compare Firmw
6. Figure 2 2 3 If target 2 is available connect the second SATA converter to the IDE connector CN15 on the controller with an IDE cable to target 2 Figure 2 3 to target 1 10 2033N User s Manual 4 Connect the rest of IDE connectors to DVD writers with IDE cables Figure 2 4 2 4 2 On Target 1 amp Target 2 1 Connect the SATA converter to the IDE cnnector CN7 the white one on the controller with an IDE cable Figure 2 5 11 2033N User s Manual 2 Connect IDE connectors except CN8 with a seal and CN14 the blue one to DVD writers with IDE cables CN8 CN7 Figure 2 6 3 If you want to connect an HDD connect it to IDE connector CN14 the blue one on the controller Figure 2 7 12 2033N User s Manual 2 4 3 Among the Host Target 1 amp Target 2 1 Connect the SATA converter of the host and that of target 1 with a SATA cable Figure 2 8 2 Connect the other SATA converter of the host and that of target 2 with another SATA cable Figure 2 9 13 2033N User s Manual 2 4 4 Checklists of Installation A Installing three sets of ARS 2033N controllers The following checklists are for you to examine the installation In the checklists H means host T1 means target 1 and T2 means target 2 Host Target 1 CN 13 SATA converter to T1 CN 14 Source HDD ODD CN 15 SATA converter to T2 HDD optional DD SATA Converter SATA converte
7. and burn Yes LCD will show the copying information as follows Copying 24X Edit 2 10 gt 2 2 2 2 means the second track of all tracks we have selected and so far we have selected two tracks from two different CDs When copying comes to an end LCD will show the message as follows Burn Complete OK 07 The system will ask if you want to keep editing Suppose we don t like to continue then press W to confirm No Continue edit next Disc No 45 2033N User s Manual Now press ENT The system will ask if you want to close all CDs sessions Use A to confirm Yes or No as shown below Close all disc s session Yes After deciding to close LCD will show the message as follows Note that you cannot listen to the music before closing sessions Closing Session Please wait 4 10 2 CD to HDD After closing sessions press ESC and to see the following figure Here the function CD to HDD is to let you select one or more tracks from CD ROM and then copy into a certain partition of HDD 10 02 Edit Track CD to HDD Edit Now press ENT and you will enter the following figure Here 1 10 means the number one of the 10 tracks and 03 25 means the playing time Select Track 1 10 03 25 46 2033N User s Manual Suppose we decide to select the first track then press ENT A will appear beside 1 10 as shown below But pressing ENT again may cancel
8. Time Button Sound Device Info System Info Quick Erase Full Erase Auto Close Tray Quick Compare and Audio Burn Speed Refer to page 24 for the menu Select function 11 53 2033N User s Manual 4 11 1 Language Now press ENT and you will see the following figure The function Language lets you select a language in which messages can be shown on LCD 11 01 Setup Language Press ENT to see the following figure The default is English Spanish Japanese Traditional Chinese and Simplified Chinese are made to order Language English 4 11 2 CD Burn Speed Now press ESC and V to see the following figure This function lets you control the burning speed of CD writers 11 02 Setup CD Burn Speed Press ENT to see the following figure The default is auto CD Burn Speed Auto 54 2033N User s Manual 4 11 3 DVD Burn Speed Now press ESC and V to see the following figure The function DVD Burn Speed lets you control the burning speed of DVD writers 11 03 Setup DVD Burn Speed Press ENT to see the following figure The default is maximum DVD Burn Speed Maximum 4 11 4 Read Speed Now press ESC and V to see the following figure The function Read Speed lets you control the reading speed of target CDs 11 04 Setup Read Speed Press ENT to see the following figure The default is maximum but there are other choices 32X 16X and 8X Read Speed Maximum
9. first track then press ENT A will appear beside 1 10 as shown below But pressing ENT again may cancel the selection Select Track 11 10 03 25 42 2033N User s Manual After selecting use to move to the End menu as shown below Select Track End 1Trk03 25 Press ENT to finish the CD editing and use A W to confirm Yes or No End edit disc and burn Yes LCD will show the copying information as follows Copying 24X Edit 1 10 gt 1 1 1 1 means the first track of all tracks we have selected and here we have just selected one track When copying comes to an end LCD will show the message as follows Burn Complete OK 07 43 2033N User s Manual The system will ask if you want to keep editing Use A W to confirm Yes or No as shown below Continue edit next Disc Yes If you want to keep editing the current source CD will eject auctomatically and the system will ask you to insert another new CD as shown below Insert next disc After inserting the new CD press ENT to edit as before Suppose we decide to select the second track then press ENT A will appear beside 2 10 as shown below Select Track 2 10 04 25 After selecting use A to move to the End menu as shown below Select Track End 1Trk04 25 44 2033N User s Manual Press ENT to finish the CD editing and use A W to confirm Yes or No End edit disc
10. 20 Setup Quick Compare Press ENT to see the following figure The default is Off but you can press W to choose a certain byte like 1 Byte 1 KB 10 KB 1 MB 10 MB etc Quick Compare Off 66 2033N User s Manual 4 11 21 Audio Burn Speed Now press ESC and to see the following figure Audio Burn Speed lets you control the burning speed of audio CDs 11 21 Setup Audio Burn Speed Press ENT to see the following figure The default is auto but there are maximum 52X 48X 40X 32X 24X 20X etc for choice Audio Burn Speed Auto 4 12 Link Select Function 12 Link Select lets you select a link mode There are four modes for choice host target rescan and general Press ESC and to see the following figure 12 Link Select Press ENT to see the following figure General is the default It is fit for a standalone copy controller Select Link Mode General 67 2033N User s Manual Press W to see the following figure Host means to link to the host while target to link to the target Select Link Mode Host Press W twice to see the following figure Rescan means the host scans its peripheral devices like targets Select Link Mode Rescan 4 13 Adv Setup Function 13 Adv Setup lets you change the system configuration This function includes 17 subfunctions UnderRun Protect Overburn Read Error Skip Format HDD Verify HDD Burn in Update Firmware Compare Fir
11. 3 It is used to scroll down through functions or menus 4 It is used to execute a selected function 5 It is used to cancel a selected function DVD Duplicator OS booting 2033N ver 1 61N 1 Figure 1 shows the firmware version of ARS 2033N Figure 2 shows OS booting 18 2033N User s Manual 1 Copy Figure 3 shows the first function Copy There are 13 functions You can press W to see but need to press ESC for 2 seconds to enter the 13th function 3 2 About HDD Installation HDD installation is not necessary but with a hard drive you can use the function of Image In other words you have one more choice to reproduce a DVD from an image file stored in the hard drive The following two subsections are about installing and not installing a 3 5 hard drive respectively 3 2 1 With a HDD If you have installed a 3 5 hard drive to your copy controller you need to operate according to the following procedures Once your copy controller detects the hard drive it will ask if you want to format A 30GB of hard drive can be divided into 6 partitions In DVD a partition occupies 5GB in CD 1GB and in DL 10GB Use function 8 Select Source to set the hard drive as the source In function 9 Image select a partition to store the data If there is no data in a selected partition place a source DVD into DVD ROM and use function 9 01 Load to transmit data from DVD into the selected partition by pressing ENT Differe
12. DVD rewriteable discs that contain data the old data will be quickly erased before simulation as shown below Erasing disc 2033N User s Manual LCD will show the testing information as follows Testing DVD 0 4384MB 7 30 When the test comes to an end LCD will show the results as follows 2 Test OK 07 Stopping the test halfway does not affect the DVDs but if the DVD rewriteable discs contain important data the data may be destroyed 4 3 Test amp Copy Function 3 Test amp Copy is to test first and then copy actually Select function 3 Put a source DVD into DVD ROM and blank DVDs into the DVD writers 3 Test amp Copy Press ENT to start simulation LCD will show the testing information as follows Testing DVD 0 4384MB 7 30 28 2033N User s Manual When the test finishes actual copying will begin as shown below Copying DVD 0 4384MB 7 30 When the whole process finishes LCD will show the results as follows 3 Test amp Copy OK 07 Note that those discs that have passed the test will be copied right away while those that haven t won t be 4 4 Verify Function 4 Verify is to examine if the target DVDs can be read correctly after copying Select function 4 4 Verify Press ENT to verify LCD will show the verification information as follows Verify DVD 0 4384MB 7 30 29 2033N User s Manual When verification comes to an end LCD will show the resu
13. Track This function is to use the copy controller as a music player You can connect a headphone to the headphone jack on the source and enjoy the music Now press ESC and V to select the function 10 03 Edit Track Play Audio Track 51 2033N User s Manual Use A V to select the track you want to play Select Track 1 10 03 25 After selecting and pressing ENT LCD will show the playing information below Playing Track 1 00 00 03 25 4 10 4 Close Session This function is to close CDs and let no data written into After closing you can put the CDs on any normal player and listen Now press ESC and V to select the function 10 04 Edit Track Close Session After pressing ENT the system will ask if you are sure to close Close all disc s session Yes 52 2033N User s Manual After pressing ENT LCD will show the message as follows Closing Session Please wait When closing finishes LCD will show the results as follows Closing Complete OK 07 Fail 0 4 11 Setup Function 11 Setup lets you change the default settings Once you change a setting remember to press ENT to save it However it is suggested to use the defaults for the optimal operation This function includes 21 subfunctions Language CD Burn Speed DVD Burn Speed Read Speed Auto Start Drive Startup Menu Auto Verify Auto Compare Auto Prescan Eject Disc Burn On The Fly Burn Mode Display
14. alphabet remember to press ENT Old Password 8 After keying in the old password remember to press ENT to confirm Then the following figure will appear New Password 9 Follow the rule mentioned above to key in a new password After keying in the system will ask you to enter the new password again Re Ent Password When it is correct you will see the following figure You have 3 chances to enter your password If you forget your password return the copy controller to ACARD for help Change OK 79 2033N User s Manual 4 13 16 Disc Counter Press ESC and V to drr the following figure Disc Counter records how many discs you have copied 13 16 Adv Setup Disc Counter Press ENT to see the following figure View means to see the records Disc Counter View Press ENT LF in the following figure means life It records the number of discs you have copied It cannot be deleted LF OK 000000001 Fail 000000000 Press V JB in the following figure means job that is every copying task It also records the number of discs you have copied but it can be deleted JB OK 000000001 Fail 000000000 80 2033N User s Manual Press W The following figure shows the record in DVD writer 2 You can pressW to see the records in other writers This kind of record can be deleted too 02 OK 000000001 Fail 000000000 Press A to return to the record of job Then pre
15. file in the partition First select the function by pressing W 9 04 Image P A Compare Image 36 2033N User s Manual Press ENT and LCD will show the comparison information as follows Compare DVD 0 4384MB 7 30 When comparison comes to an end LCD will show the results as follows Compare OK 1 Fail 0 Diff 0 Press ENT to see the details of the source as shown below Src 01 DVD ROM Total 4384MB Press ENT to see the details of the target If the comparison is identical LCD will show the message as follows Tgt 00 HDD P A Identical If comparison fails LCD will show the failure By pressing ENT twice LCD will show that the contents of the source and those of the target don t match as follows Tgt 00 HDD P A TOC not match 37 2033N User s Manual 4 9 5 Select Image This function is to select a partition in the hard drive First select the function by pressing W 9 05 Image P A Select Image After installing a hard drive your copy controller will format it automatically Each partition occupies 5GB The number of partitions is dependent on the hard drive s capacity The partitions are alphabetically arranged Select a partition by pressing A V and LCD will show the message as follows Select Partition A DVD 4384MB After the partition is selected LCD will show the results as follows Set Partition to A 4 9 6 Image Src Drive This function
16. hardware is used together with ACARD s recording software Ha DVD Burner the combination will be the best solution 1 2 Features Standalone IDE to IDE DVD copy controller Totally independent without installing hardware or software Supports a 3 5 hard drive Supports high speed 1 to 21 DVD copying A user friendly interface with message showing LCD Optional functions for applications 2033N User s Manual 1 3 Specifications ACARD ATP 867 IDE processor 32 bit RISC CPU 64 MB DDR memory 10 independent IDE channels External SATA cable s for connecting 2 to 3 sets of 2033N 2X16LCD 4 membraned buttons on the panel 512 KB flash memory for boot loader 2 MB flash memory for copy code Firmware update via DVD ROM Power Voltage 5Vx596 Current 1 5A Max Environment Operation 0 C to 60 C Nonoperation 20 C to 85 C Humidity 15 to 90 Dimension D 225 W 150 H42 mm 1 4 System Requirement upright external case 9 10 x 5 25 Power supply 300 watt or above ATA133 cable DVD ROM X1 DVD writer X 7 to 21 Hard drive optional HDD tray optional AEC 4420P optional 2033N User s Manual Chapter 2 Hardware Installation Before installing ARS 2033N notice that there are three kinds of packages the copy controller only a whole copying system and a system without DVD drives 2 1 Copy Controller Only Unpack the package and examine if there is any defect or malfunction Prepare a DVD ROM Prepare 7 to 21
17. is to select DVD ROM or any of the DVD writers as the source from which you can load data into a particular partition as an image file 38 2033N User s Manual First select the function by pressing V 9 06 Image P A Image Src Drive Then use A V to select DVD ROM or any of the DVD writers as the source Select Img Src 01 IDE1 DVD ROM After selecting the source such as DVD ROM you can press ENT and LCD will show the message as follows Load image from Drive ID 01 4 9 7 Image Format Info This function is to see how you have formatted your hard drive It is related to function 13 4 Format HDD There are 3 formats for choice CD DVD and DL Double Layer Now press ESC and V to see the following figure 9 07 Image P A Image Format Info 39 2033N User s Manual Press ENT to see the following figure This figure shows that the hard drive has been formatted as DVD Image Format Info DVD If your hard drive is a new one and not formatted yet LCD will show the message as follows after powering on HDOO not Format Format HDD Yes Press ENT to confirm Yes and you will see the following figure HD Partition Format Select DVD You can press W to select CD or DL 4 9 8 Edit This function is to name a certain partition but only when the partition contains an image file can title editing be valid First select the function by pressing W 9 08 Image P A Ed
18. the selection Select Track 11 10 03 25 After selecting use to move to the End menu as shown below Select Track End 1Trk03 25 Press ENT to finish the CD editing and use A W to confirm Yes or No End edit disc and burn Yes Then the track as an image file will be loaded into HDD LCD will show the loading information as follows Load PO 24X Edit 140 gt 1 1 When loading comes to an end LCD will show the message as follows Image load OK 47 2033N User s Manual The system will ask if you want to keep editing Use A W to confirm Yes or No as shown below Continue edit next Disc Yes If you want to keep editing the current source CD will eject auctomatically and the system will ask you to insert another new CD as shown below Insert next disc After inserting the new CD press ENT to edit as before Suppose we select the second track and then press ENT A will appear beside 2 10 as shown below Select Track 2 10 04 25 After selecting use to move to the End menu as shown below Select Track End 1Trk04 25 Press ENT to finish the CD editing and use A V to confirm Yes or No End edit disc and burn Yes 48 2033N User s Manual Then the track as an image file will be loaded into HDD LCD will show the loading information as follows Load PO 24X Edit 2 10 gt 2 2 When loading comes to an end LCD will
19. toad tanta eh ttes 57 4 11 8 Auto Compare eet or order etae eR eoe tero eade e vupu ae Urn dese 58 4 119 Auto PEeSCI ice teria itae e pho ree tR ope Ho ER RR OPER UR DN E pKRER RE PEDEUR a 58 E SENILIS DIM ET NC 59 4 11 11 Burn On The Fly iusto RENI ASSENTIOR IG UUES 59 4 11 12 Burn MOde iioe n sies ey eiae etie dero rone bisos tose P EU PP dupP deo 60 4 11 13 Display NITE E ER ssussess sais tsaa 61 4 11 14 Button Sound vii cessccssnccdacsedecscvenssnedssedstcacsensssovssdosasvesssecavedstonts 61 4 11 15 DeyICe Info cisctsspscecisssicceiscseatancstiaceanposacadeadsoehisotedanastoacseaeceonss 62 4 11 16 System NfO eene ori Sorte Hae reor terrenae Eee e vupIE Ur x edet 63 4 11 17 Quick Erase zu ont ete tepore e etna Ere eHReEPEUeIS RE PR EER EIN io De aua eoe PER Rbr baa 63 411 19 Full C ES NADEL PM iisas 64 4 11 19 Anto Close Tray s oreteestoe eee RERO GE NETS ERIGI NNUS 65 4 11 20 Quick Compare Leer sorde erae ee PR eno noe P roO e EE er Y Ye PV E Er px endete 66 4 11 21 Audio Burn Speed cec ecce ee eere ee ee sete eese eo eee eese e 67 4 12 Link Select aee od Ht rei Lec testa 4 13 Ady Setup 42i roe tetas tne ko ene ths ie uos o Qa has cents 68 4 13 1 UnderRun Protect eee tere reote testor o ee eoe terrore no eo eene a re 69 4 13 2 OVEEDUFT eee retro entero orae esu o na eoe e PY P Pate Ph d prec oer pe op iuTa 69 4 13 3 Read Error Skip Ge oe iet e SE eS EN ESSO NENEH NE PER URE UE e nei EU US 70
20. 4 9 7 Delete Image sissie cstadceiucioacdessacceabacasvcasestscsitevivccaeasacastarescoeds 35 4 9 3 nage Info oio tee eere err serae nva e as teet ste issos UNI NE PETER ARS 36 4 9 4 Compare Image oe teestoee eot NERO area eden 36 4 9 5 Select InidBe creesce rentre PE Ner desk PeY e e PR eoe ne Pro eR E Nvv PUR Und e dmt 38 49 6 Image Sre Drive 5iieeeeenettse venei nore OPEN NUH EUH I ONUE NEIN UNE UE NOR ososi 38 4 9 7 Image Format fo eiseeseek rta ee Reese mE ERR ENS Pu HUNE radere 39 49 8 Edit iue etd et tn btts eius 40 4 10 Edit Track for CD only 41 4 10 1 CDt CDi nea Foe oi tE eterne Igne Rod eEE etsi aene ares eks 42 4 10 2 CD to HDD iesecuice iecore teda iuo iae esarre ees Sota uDEecin Grape sue SR aeuo Da sdoe 46 4 10 3 Play Audio Track uis eeeietee ette etr teh te Paene te ev YU eo ee atn e ne tr Eo ue R orn 51 4 10 4 Close Session POS CN 52 AE a D sesto cra E A E E E A N E T TL LANGUAGE 22 eid iocari tri Te IE RE copa e sasien sae oeni isso aissis 54 4 11 2 CD Burn Speed ier iere rna e PERS Eee motae NER YE HH NE PORT ssaa 54 4 11 3 DVD Burn Speed uestes eot NE NO GE NET SINN EH EEUNI IC Ud S 55 MATA Read Sp ed iere ero eode k Prae e YR eoe eoe etu RR ere YE dE inesse iser 55 4 11 5 Auto Start Drive sissies eiie te pao rotor tetto Rae ae bERR OE Pet E eK bbU b boton b 56 11 6 Startup M nu coser cor ostrea e Reno EeeY tos eru Eo eie vu HUE roO H PIE 56 TTL Auto Verify iunio
21. 413 4 Format HDD eere eee eee eese oe o ee e erre rne o eae eer ori verha eee eee 70 4 13 5 Verify HDD ooa cote EORR E Font ede EN 71 4 13 6 Bu rti In ii der eee ee eere enano neat oo eos de rro eade o caos desee adea eod 72 4 13 7 Update Firmware 5 255 220 te aaro Vip d eta Beda oso tElo Ca Fe dept Urea tipps 73 4 13 8 Compare Firmware o ecce iore euh ee Pene r neo ree EF oe aeree re ERE 74 4 13 9 H W Diagnostic ceoecses et RR LO eT See EUREN 74 4 13 10 Load Default eoesssooecssoceessccecessscccesscccessccecsscsecsesseceessoceesssse 75 4 13 11 DID cH RM OPENS 76 4 13 12 ISRC MON eiotideeee sux eee Qeci prex ee ehe eot eade cu ee v Moe e dev PR Pe PERSE 76 4 1313 USB OPO s e OI eR RISO ROB eU EE 77 1 13 14 C DET EXT iiio re tco eei dec cbescacdeasevacgevaduissdadesisusabedsotseovssatdovsscss 77 413 15 Password sc csssscsesssscissdescetstsesesdeseccssisecsedssusdesesacsesesbesseesscessseese 78 4 13 16 Dise Counter i isccccdstec seta ere eeh dones ee place tenue suse vh oe eer rp exe pana 80 4 13 17 Auto Save Image oce ON REFER QE ERU SRI EE EURENE 82 Chapter 5 Troubleshooting 83 5 1 ABOULECDHDS acte serit pne eie voie ti ieto thesal ee ques 83 5 2 About Error Messages e c eee ee eere ee eee eerta aeneo 83 5 3 About DVD ROM DVD Writers e eee 83 54 About Buttons esteso eve enero rhn oae e pa EtNe s Fa cEeik e ar uR a 83 5 5 About DVD Writer Not
22. ARS 2033N 1 to 21 Copy Controller User s Manual Ver 1 0 Attention Wait over 5 seconds to power on after shutdown to prevent the abnormal operation of the system ACARD ECHNOI UO CG Y Copyright 2006 ACARD Technology Corp Release March 2006 ce FE Copyright and Trademark The information in this manual is subject to change without prior notice and does not represent a commitment on the part of vendor who assumes no liability or re sponsibility for any errors that may appear in this manual ACARD is the trademark of ACARD Technology Corp This manual contains materials protected under International Copyright Laws AII rights reserved No part of this manual may be reproduced transmitted or transcribed without the expressed written permission of the manufacturer and author of this manual ACARD s ARS 2033N Copy Controller is used for copying and editing personal audio and video data Violating Copy Right is a criminal act ACARD s Copy Con troller only supports legal backup operation ACARD Technology Corp is not responsible for illegal recording Table of Contents Chapter 1 Introduction eere 6 1 1 cago pP nem 6 ESAMI RD RE 6 1 3 Specifications iei enr oio herr Rae 7 1 4 System Requirement sssooecssssocecssooccesssooecssssocecssssoseeeso 7 Chapter 2 Hardware Installation 8 2 1 Copy Contr
23. DVD writers Prepare a 3 5 hard drive optional All IDE devices are in Master mode but when connecting a hard drive DVD ROM is set as Slave while hard drive as Master e Be sure that the watt of power supply is sufficient 2 2 A Whole System e Unpack the package and examine if there is any defect or malfunction e Prepare a 3 5 hard drive optional e Be sure that the watt of power supply is sufficient 2 3 A System without DVD Drives Unpack the package and examine if there is any defect or malfunction Prepare a DVD ROM Prepare 7 to 21 DVD writers Prepare a 3 5 hard drive optional Be sure that the watt of power supply is sufficient 2033N User s Manual 2 4 How to Install Take two sets of ARS 2033N controllers as host and target or three sets as host target 1 and target 2 respectively In the first case you can connect 14 DVD writers and need two sets of AEC 4430H SATA converters to act as bridges In the second case you can connect 21 DVD writers and need four sets of SATA converters From 2 4 1 to 2 4 3 we will take three sets of controllers and four sets of SATA converters to demonstrate the installation 2 4 1 On the Host 1 Connect an HDDYODD to the IDE connector CN14 the blue one on the control ler and short CN2 s first pair of pins Figure 2 1 2033N User s Manual 2 Connect the SATA converter to the IDE connector CN13 on the controller with an IDE cable to target 1
24. OM or any one of the DVD writers into the current partition of the hard drive P A means partition A 9 01 Image P A Load Press ENT to load LCD will show the loading information as follows Load A DVD 096 4384MB 7 30 34 2033N User s Manual After the image file is successfully loaded LCD will show the results as follows Image load OK If there is an image file existing in the current partition the system will ask you whether to overwrite it or not Please use A V to confirm Yes or No Image Exists Overwrite Yes 4 9 2 Delete Image If you want to delete an image file stored in a particular partition you can use the function Delete Image to do so First select the function by pressing W 9 02 Image P A Delete Image The system will ask if you are sure to delete Use A W to confirm Yes or No Delete Image in Partition A Yes 35 2033N User s Manual After the image file is deleted LCD will show the results as follows Partition A Image is deleted 4 9 3 Image Info This function is to show the basic information of an image file stored in a particular partition First select the function by pressing W 9 03 Image P A Image Info Press ENT and LCD will show the information of the image file as follows Disc Type DVD ROM Capacity 4384MB 4 9 4 Compare Image This function is to compare the contents of the source DVD and those of the image
25. Readable 84 5 6 About High Failure Rate eeeeeeeeeeee 84 5 7 About Firmware Update e eere 84 5 8 About Function 13 and Cancellation 84 Appendix 1 List of Functions OD Appendix 2 LCD Messages eere OF Technical Support Form e 91 2033N User s Manual Chapter 1 Introduction 1 1 Overview ARS 2033N is a 1 to 21 copy controller supporting 12X CD DVD writers It doesn t need connecting to a computer Through the LCD and 4 buttons on the copy controller s panel you can copy data audio or video CD DVD easily and quickly It is fit for companies desire to do a small amount of production Usually if you want to back up a lot of CD DVDs you have to boot the computer and do the job via a recording program It takes time to learn how to use the software and more time to execute the recording In view of this ACARD has launched ARS 2033N for you to copy multiple discs without efforts ARS 2033N is a valuable product of technology You can use it as a standalone copy controller Besides if you have purchased ACARD s AEC 4420P USB Link you can connect it to the computer to ARS 2033N and to one of the DVD writers that are connected with the copy controller Thus the copy controller becomes an exter nal writer for the computer When the
26. are is to compare the current firmware version and the newly downloaded version It can prove if the downloaded version is the newest one 13 08 Adv Setup Compare Firmware 4 13 9 H W Diagnostic Press ESC and V to see the next figure H W Diagnostic is to test the system 13 09 Adv Setup H W Diagnostic Press ENT to see the next figure The system will do the button test self test of SDRAM the hardware connection test and flash test All test results will be shown on LCD It is the easiest way to know if the system is normal LCD Test Start 74 2033N User s Manual When all tests finish LCD will show the message as follows Test finished 4 13 10 Load Default Now press ESC and to see the next figure Load Default is to make all changed settings return to defaults 13 10 Adv Setup Load Default Press ENT to see the next figure Use A V to confirm Yes or No Load Default Config Yes When default loading finishes LCD will show the results as follows Load Default OK 75 2033N User s Manual 4 13 11 CD G Now press ESC and V to see the following figure CD G is a kind of special copying format This function supports this special format 13 11 Adv Setup CD G Press ENT to see the next figure The default is Off Press W to select On CD G Off 4 13 12 ISRC amp MCN Now press ESC and to see the following figure ISRC and MCN are special copying format
27. d exclusively for editing a collection of favorite songs from CDs During operation if you don t understand an LCD message see Appendix 2 4 1 Copy Function 1 Copy is to copy data from a source DVD directly into blank DVDs Before copying be sure that the source DVD is placed into DVD ROM or there are data in a certain HDD partition if you have installed a hard drive If you are uncertain of actual copying use Function 2 Test to simulate first Select function 1 Put a source DVD into DVD ROM and blank DVDs into the DVD writers rewriteable DVD containing old data is also usable but the old data will be automatically erased 1 Copy After the DVD ROM and DVD writers detect DVDs press ENT to start copying LCD will show the copying information as follows Copying DVD 0 4384MB 7 30 26 2033N User s Manual When copying is in progress MB and time will decrease while the percentage of completion will increase MB means the size of data that you want to copy When copying comes to an end LCD will show the results as follows The passed DVDs will eject automatically 1 Copy OK 07 4 2 Test Function 2 Test is to simulate the copying progress When simulation finishes there will be no data really written into DVDs Select function 2 Put a source DVD into DVD ROM and blank DVDs into the DVD writers Only a DVD R disc supports this function 2 Test Press ENT to start simulation If you use
28. eading fails an error message will appear on LCD Get a new source DVD to try If the copy controller hasn t detected any device after powering on an error message will appear on LCD 5 3 About DVD ROM DVD Writers Ifa DVD ROM ora DVD writer cannot read confirm the format of the source DVD and check if it is damaged Use any DVD writer to read the source DVD If it works the DVD ROM is probably defective or not compatible with the source DVD 5 4 About Buttons If you press any one of the four buttons on the panel but there is no response it is perhaps that the button cannot function well Inspect the jumper setting 83 2033N User s Manual 5 5 About DVD Writer Not Readable After copying if the DVD writer is not readable use Compare to examine or get another DVD ROM to test 5 6 About High Failure Rate If the failure rate of copying is high do the following things to improve e Lower the speed of DVD writer e Inspect if the blank disc s quality is good e Update the firmware e Inspect the DVD writer s maximum writing speed If the speed is over 8X copy the data to a hard drive first and then transmit to the disc 5 7 About Firmware Update If you cannot update the firmware inspect the firmware Perhaps you have downloaded a wrong file Failure in firmware update may cause the copy controller to fail in booting Under the circumstances return the control board to distributor for repair 5 8 Ab
29. here are 21 subfunctions 11 1 Language 11 2 CD Burn Speed 11 3 DVD Burn Speed 11 4 Read Speed 11 5 Auto Start Drive 11 6 Startup menu 11 7 Auto Verify 11 Setup 11 8 Auto Compare 11 9 Auto Prescan 1 EX 10 Eject Disc 1 as 11 Burn On the Fly 1 E 12 Burn Mode 1 13 Display Time 1 E 14 Button Sound 1 15 Device Info 1 ex 16 System Info 1 17 Quick Erase 1 18 Full Erase 1 ER 19 Auto Close Tray 11 20 Quick Compare 11 21 Audio Burn Speed 24 In Function 13 there are 17 subfunctions 2033N User s Manual 13 1 UnderRun Protect 13 2 Overburn 13 3 Read Error Skip 13 4 Format HDD 13 5 Verify HDD 13 6 Burn in 13 7 Update Firmware 13 Advanced Setup 13 8 Compare Firmware 13 9 H W Diagnostic 13 10 Load Default 13 11 CD G 13 12 ISRC amp MCN 13 13 USB Option 13 14 CD TEXT 13 15 Password 13 16 Disc Counter 13 17 Auto Save Image 25 2033N User s Manual Among the 13 functions Function 10 Edit Track is designe
30. ialize the memory of the system Load Default Config Do you want to load the default settings No Erasable Disc in DVD RW The disc on the DVD RW device is not rewritable Preparing eg eee The system is preparing to record Press a Key to Eject Fail Disc Press any key to eject the failed disc after copying Press a Key to Eject Good Disc Press any ket to eject the good disc after copying Read disc error sss During comparison the disc cannot be read Save new config Fail The new setting of configuration cannot be saved Source Disc Empty The source disc doesn t contain any data Source Disc Not Ready Source disc is not ready to be read Source Drive Not Ready sess Source drive is not ready to read 2033N User s Manual Src amp Tgt can t in the same channel During comparison the source and target discs cannot be in the same channel Target Disc Not Empty sssssssesee The target disc still has data Target Disc Not Ready Target disc is not ready to be written into Target Drive Not Ready Target drive is not ready to write Target overflow The target disc hasn t enough capacity to store new data TOC not match sessss The comparison re
31. it 40 2033N User s Manual Press ENT A title should be composed of 1 to 13 characters The character can be A B C etc or 1 2 3 etc or the combination of both Use A V to select the number or alphabet After selecting a desired one press ENT Edit Title After keying in the title press ENT to see the following figure Edit Sub1 Title Sub1 Title lets you key in a subtitle 1 You can press ENT again to key in a subtitle 2 When title editing is completed you will see the next figure Edit Title OK 4 10 Edit Track for CD only Function 10 Edit Track is exclusively designed for editing a collection of favorite songs from CDs In other words it can collect different tracks songs on a number of CDs and merge them into a single CD This function includes 4 subfunctions CD to CD CD to HDD Play Audio Track and Close Session Refer to page 23 for the menu 41 2033N User s Manual Select function 10 10 Edit Track 4 10 1 CD to CD Now press ENT and you will see the following figure Here the function CD to CD is to let you select one or more tracks from CD ROM and then copy into blank CD R RWs 10 01 Edit Track CD to CD Edit Now press ENT and you will see the following figure Here 1 10 means the number one of the 10 tracks and 03 25 means the length of track Select Track 1 10 03 25 You can press W to see the second track and so on Suppose we decide to select the
32. lts as follows 4 Verify OK 07 4 5 Compare Function 5 Compare is to make a comparison between the source DVD and the target DVDs after copying Select function 5 Put the source DVD into DVD ROM and the target DVDs into DVD writers 5 Compare Press ENT to compare LCD will show the comparison information as follows Compare DVD 096 4384MB 7 30 When comparison comes to an end LCD will show the results as follows Compare OK 07 Fail 0 Diff 0 30 2033N User s Manual Press ENT to see the details of source 1 as shown below Src 01 DVD ROM Total 4384MB Press ENT to see the details of source 2 If the comparison is identical LCD will show the message as follows Src 02 DVD RW Identical If comparison fails LCD will show the failure By pressing ENT twice LCD will show that the contents of source 1 and those of source 2 do not match as follows Src 02 DVD RW TOC not match 4 6 Prescan Function 6 Prescan is to scan if the source DVD can be read correctly and by the way to test the reading speed Select function 6 Put the source DVD into DVD ROM 6 Prescan 31 2033N User s Manual Press ENT to prescan LCD will show the scanning information as follows Scaning DVD 0 4384MB 7 30 When scanning finishes and the source DVD can be read correctly LCD will show the results as follows PreScan OK 4 7 Disc Info Function 7 Disc Info is t
33. mware H W Diagnostic Load Default CD G ISRC amp MCN USB Option CD TEXT Password Disc Counter and Auto Save Image Refer to page 25 for the menu Now press ESC to return to Function 12 Then press ESC for 2 seconds to enter Function 12 01 as the following figure shows 13 01 Adv Setup UnderRun Protect 68 2033N User s Manual 4 13 1 UnderRun Protect Now if you press ESC you can enter Function 12 as the following figure shows 13 Adv Setup UnderRun Protect lets you control On and Off of Buffer Under Run Protection Press ENT to see the following figure The default is On Press W to select Off UnderRun Protect On 4 13 2 Overburn Now press ESC and WV to see the following figure Overburn lets you decide whether to copy beyond the limit of the CD or not 13 02 Adv Setup Overburn Press ENT to see the following figure The default is Off Press W to select On Overburn may make a DVD writer damaged and data incomplete Overburn Off 69 2033N User s Manual 4 13 3 Read Error Skip Now press ESC and V to see the following figure Read Error Skip is to ignore any error that occurs during copying Under normal circumstances when an error occurs during copying a message will appear on LCD Yet you can use Read Error Skip to copy some defective DVDs 13 03 Adv Setup Read Error Skip Press ENT to see the following figure The default is Off Press W to select On Read Err
34. nt data can be stored in different partitions Switch to function 1 Copy by pressing A Place blank DVDs into DVD writers and press ENT to start copying 19 2033N User s Manual When copying comes to an end the passed DVDs will eject automatically The default is automatic ejecting but you can change it The failed DVDs will remain in the writers The default is keeping failed DVDs in the writers but you can change it To take the failed DVDs you need to press the eject buttons on the writers During operation do not press any button on your copy controller because interruption may harm the device and DVDs will be damaged too 32 2 Without a HDD If you haven t installed a 3 5 hard drive to your copy controller you need to operate according to the following procedures Place a source DVD into DVD ROM Switch to function 1 Copy by pressing A Place blank DVDs into DVD writers and press ENT to start copying When copying comes to an end the passed DVDs will eject automatically The default is automatic ejecting but you can change it The failed DVDs will remain in the writers The default is keeping failed DVDs in the writers but you can change it To take the failed DVDs you need to press the eject buttons on the writers 20 2033N User s Manual Identify two different cables before hardware installation 1 Three connectors for DVD ROM or optional HDD
35. o see the following figure The default is On Press W to select Off Burn On The Fly On If your copy controller doesn t connect a hard drive LCD will show the message as follows No Valid HDD 4 11 12 Burn Mode Now press ESC to return to Function 11 and then select part 12 Burn Mode as the following figure shows Burn Mode lets you control the burning modes There are two modes DAO Disc At Once and TAO Track At Once They only support CD If the DVD writer doesn t support the mode you have selected the copy controller will automatically switch to another mode 11 12 Setup Burn Mode Press ENT to see the next figure The default is DAO Press W to select TAO Burn Mode DAO 60 2033N User s Manual 4 11 13 Display Time Now press ESC and to see the following figure Display Time is to show the copying time 11 13 Setup Display Time Press ENT to see the following figure The default is On Press W to select Off Display Time On 4 11 14 Button Sound Now press ESC and to see the following figure Button Sound lets you control the sound of a button when you press it 11 14 Setup Button Sound Press ENT to see the next figure The default is On Press W to select Off Button Sound On 61 2033N User s Manual 4 11 15 Device Info Now press ESC and to see the following figure Device Info shows the information of the DVD ROM and any of the DVD writer
36. o show the basic information of source DVD Select function 7 Put the source DVD into DVD ROM 7 Disc Info Press ENT and LCD will show the DVD information as follows Disc Type DVD ROM Capacity 4384MB 32 2033N User s Manual 4 8 Select Source Function 8 Select Source is to let you select the data on DVD ROM DVD writers or HDD as the source from which copying will be done Select function 8 8 Select Source Press ENT and then press A to select the source as shown below Src DVD ROM 01 IDE1 Master After selecting the source such as DVD ROM you can press ENT and LCD will show the message as follows DVD ROM selected Suppose you select HDD as the source and try to copy from one of its partitions but the partition contains no data an error message will appear on LCD At this moment you can switch to another partition that contains data or use function 9 Image to load the data into the chosen partition first 33 2033N User s Manual 4 9 Image Function 9 Image is valid only when you have installed a hard drive This function includes 8 subfunctions Load Delete Image Image Info Compare Image Select Image Image Src Drive Image Format Info and Edit The loaded data is called an image file Refer to page 23 for the menu Select function 9 9 Image 4 9 1 Load Now press ENT and you will see the following figure Here the function Load is to let you load data from DVD R
37. oller Only eerie tette ten 8 2 2 A Whole System eetnede eter eu EI necessitate dela 8 2 3 A System without DVD Drives eeeeeeee eren 8 2 4 How to Install eeieeesdei ree oot EE eee ete aes 9 254 D Con the Hosp aie Papi Foe Pape BER e pr do RE RR IPe Fon AREE MER GERE Repo Gd 9 2 4 2 On Target 1 amp Target 2 eese ee eres eese eene eene een anao 11 2 4 3 Among the Host Target 1 amp Target 2 13 2 4 4 Checklists of Installation c eeeee scere eerte e eene tne 14 2 5 The Board Lay0Ut onere eterne 16 Chapter 3 Basic Instructions 18 3 1 Buttons and ECD iau e eee eerta Ere neenes 18 3 2 About HDD Installation eere eee eere 19 S451 With a HDD uiuocisso so Ware co tnis iios de IPRC ERR CPU ER Ke ssia 19 3 2 2 Without a HDD uio erit ina ee IE EIER LORS ABRE OE ERN UA RE VERRE RD 20 Chapter 4 Functions 5 ences oeste eine e eee o b sss 22 TL CODY iue eei eq eed tee EE Peer eiie 26 LS MM II cc P 27 43 Test amp CODY oorr I tenete iue eere rear cte 28 LR MUNERE TN MM 29 4 5 WCOMIPANG oii eir HEELS asiha tib 30 LEGE looge c 31 4 7 Disc Into ueneno Det ees 32 48 Select SOUFGCE eiae eee eo tnra epo dee anos ee iv sodesecssvksesseseteess 33 41 9 E 11E K uie eo iE eene 34 L5 NE prot Pec c 34
38. or Skip Off 4 13 4 Format HDD Now press ESC and V to see the following figure Format HDD is to partition the hard drive But before formatting all data on the hard drive will be deleted 13 04 Adv Setup Format HDD Press ENT to see the next figure In DVD a partition occupies 5GB in CD 1GB and in DL 10GB If you format once more the old data will be lost HD Partition FormatSelect DVD 70 2033N User s Manual Use A V to select A T A T means that the system searches consecutive and enough space automatically for you to load an image file according to the hard drive s capacity HD Partition Format Select A T 4 13 5 Verify HDD Now press ESC to return to Function 13 and then select part 5 Verify HDD as the following figure shows Verify HDD is to verify if the hard drive or any of its partitions can work well 13 05 Adv Setup Verify HDD Press ENT to see the next figure Use A V to confirm Disk or Partition Verify Disk or Partition Disk Press ENT to verify After verification LCD will show the results as follows Verify Hard Disk OK 71 2033N User s Manual 4 13 6 Burn in Now press ESC and WV to see the following figure Burn in is to simulate the copying progress many times The time can be from 1 to 1000 After each cycle of simulation the DVDs on the DVD writers will eject automatically and recede for the next bout of simulation 13 06 Adv Setup Burn in
39. out Function 13 and Cancellation Press ESC for 2 seconds to execute function 13 Advanced Setup During operation if you want to cancel a function like Copy Test Verify etc press ESC for 2 seconds too 84 2033N User s Manual Appendix 1 List of Functions 1 Copy 2 Test 3 Test amp Copy 4 Verify 5 Compare 6 Prescan 7 Disc Info 8 Select Source 9 Image When connecting a hard drive 9 Load 9 2 Delete Image 9 3 Image Info 9 4 Compare Image 9 5 Select Image each partition is 5GB 9 6 Select Src Drive 9 7 Image Format Info 10 Edit Track for CD only 10 1 CD to CD 10 2 CD to HDD when connecting a hard drive 10 3 Play Audio Track 10 4 Close Session 11 Setup 11 1 Language English 11 2 CD Burn Speed Auto 11 3 DVD Burn Speed Maximum 11 4 Read Speed Maximum 11 5 Auto Start Drive Off 11 6 Startup Menu Copy 11 7 Auto Verify Off 11 8 Auto Compare Off 11 9 Auto Prescan Off 11 10 Eject Disc Eject Good Only 11 11 Burn On the Fly On 11 12 Burn Mode DAO 85 2033N User s Manual 11 13 Display Time On 11 14 Button Sound On 11 15 Device Info 11 16 System Info 11 17 Quick Erase 11 18 Full Erase 11 19 Auto Close Tray 11 20 Quick Compare Off 11 21 Audio Burn Speed Auto 12 Link Select General 13 Advanced Setup 13 1 UnderRun Protect On 13 2 Overburn Off 13 3 Read Error Skip Off 13 4 Format HDD 13 5 Verify HDD 13 6 Burn in 13 7 Update Firmware 13 8 Compa
40. r from H T Controller 14 2033N User s Manual B Installing two sets of ARS 2033N controllers The following checklists are for you to examine the installation In the checklists H means host and T means target Host Target Power supply Power supply N A open SATA converter from H Jumper short SATA converter to T Source HDD ODD CN 11 CN 12 CN 13 CN 14 HDD optional CN 16 SATA Converter SATA converter from H T Power supply Controller 15 2033N User s Manual 2 5 The Board Layout The board layout of ARS 2033N is shown as follows As indicated when the controller is used as host CN2 s first pair of pins should be short CNW z CHO 2E s A E EEU E TM 1 1 i J E amum EA Sapte inna 4 zu s D e WIH ap Cyl 9 H f Ej E T s EB 2033N User s Manual The board layout of AEC 4430H as host is shown as follows E BE dean EV Made In Telwan C Jim us um ma m n MW TA GN i4sn H REVII Wada j To wif m unit EY i l p The front i The back 2033N User s Manual Chapter 3 Basic Instructions 3 1 Buttons and LCD There are 4 membraned buttons and an LCD on the panel of ARS 2033N 1 2 4 ACARD a uJ ER v ESC 3 5 1 It shows all functions and messages 2 Itis used to scroll up through functions or menus
41. re Firmware 13 9 H W Diagnostic 13 10 Load Default 13 11 CD G Off 13 12 ISRC amp MCN Off 13 13 USB Option Off 13 14 CD TEXT Off 13 15 Password Off 13 16 Disc Counter 13 17 Auto Save Image 86 2033N User s Manual Appendix 2 LCD Messages 1 Normal Conditions All data will be lost erase All data on the disc will be lost Confirm the erasing of data Analyzing nb nne HR s Analyze the source disc Audio Disc Can t compare The system cannot compare the audio discs Cannot read TOC The system cannot read the contents of disc Check Target Please Wait The system is checking the target device Detect Drives Detect what drives are connected with the system DVD RW does not Support the Func DVD RW doesn t support this function Erase Finished The erasing of data comes to an end Erasing disc sss The system is erasing the data on the disc Fail to get Drive Info The drive information cannot be obtained Fail to get Src Disc Info The information of source disc cannot be obtained Hold ESC to exit Press ESC for a second to terminate the test Identical oes The comparison results are the same Initialize SDRAM Init
42. ress ENT to see the next figure Use A V to confirm Yes or No All data will be lost erase Yes After confirming Yes and pressing ENT LCD will show the message as follows Erasing disc 45 00 Full When erasing finishes LCD will show the results as follows Full Erase OK 07 Fail 00 4 11 19 Auto Close Tray Now press ESC and WV to see the following figure Auto Close Tray is to close the writer s tray automatically It is related to function 11 5 Auto Start Drive If you haven t set any writer to copy in function 11 5 this function will be invalid 11 19 Setup Auto Close Tray 65 2033N User s Manual Press ENT to see the following figure Auto Close Tray 5 Here 5 means that it takes 5 seconds to close the writer s tray automatically after copying finishes and the tray is ejected Besides 5 seconds there are 10 15 20 25 30 35 40 45 and 50 seconds for choice If you have set one or all seven writers in function 11 5 and choose 10 seconds here then one writer s tray or all seven writers trays will be closed in 10 seconds after copying finishes 4 11 20 Quick Compare Now press ESC and to see the following figure Quick Compare is related to function 5 Compare It lets you set a certain byte When the error of atarget DVD is beyond the set byte the comparison between the source DVD and the target DVD will stop Yet the comparison of the other 6 target DVDs will continue 11
43. ress W to select On Auto Compare Off 4 11 9 Auto Prescan Now press ESC and to see the following figure Auto Prescan is to scan automatically if the source DVD can be read correctly and by the way to test the reading speed 11 09 Setup Auto Prescan Press ENT to see the following figure The default is Off Press W to select On Auto Prescan Off 58 2033N User s Manual 4 11 10 Eject Disc Now press ESC and V to see the following figure Eject Disc provides three choices Eject Good Only Eject All Disc and Do Not Eject Eject Good Only means that the DVDs will eject automatically only when they are copied successfully Eject All Disc means that the DVDs will eject automatically whether they are copied successfully or not Do Not Eject means that you need to eject the DVDs manually when copying finishes 11 10 Setup Eject Disc Press ENT to see the following figure The default is Eject Good Only Press W to select Eject All Disc or Do Not Eject Eject Disc Eject Good Only 4 11 11 Burn On The Fly Now press ESC and V to see the following figure Burn On The Fly lets you control the copying methods When the setting is On the data will be copied directly from the source DVD to the target DVDs When the setting is Off the data will be loaded into a partition of HDD first and hence copying will be done 11 11 Setup Burn On The Fly 59 2033N User s Manual Press ENT t
44. s This function supports them 13 12 Adv Setup ISRC amp MCN Press ENT to see the next figure The default is Off Press W to select On ISRC amp MCN Off 76 2033N User s Manual 4 13 13 USB Option Now press ESC and to see the next figure USB Option lets you switch to the USB mode if your copy controller has connected a PC 13 13 Adv Setup USB Option Press ENT to see the following figure The default is Off Press W to select On USB Option Off 4 13 14 CD TEXT Now press ESC and V to see the following figure CD TEXT is a kind of special copying format This function supports this special format 13 14 Adv Setup CD TEXT Press ENT to see the next figure The default is Off Press W to select On CD TEXT Off 77 2033N User s Manual 4 13 15 Password Now press ESC and to see the following figure Password is set to protect your copy controller 13 15 Adv Setup Password Press ENT to see the following figure The default is Off Password Off Press W to see the following figure Change means to change a preset or an old password into a new one Password Change Press W to see the following figure Old Password 2 78 2033N User s Manual Use A V to key in the default 85122290 A password should be composed of 1 to 13 characters The character can be A B C etc or 1 2 3 etc or the combination of both After selecting a desired number or
45. s you have installed 11 15 Setup Device Info Press ENT to see the next figure 01 IDE1 Master DVD ROM PIONEER Press ENT to see the next figure DVD ROM DVD 121 1 07 Press W twice to see the next figure 02 IDE2 Master DVD RW PIONEER Press ENT to see the next figure DVD RW DVR 107D 1 05 62 2033N User s Manual 4 11 16 System Info Now press ESC and WV to see the following figure System Info shows the information of the system 11 16 Setup System Info Press ENT to see the next figure DVD Duplicator 2033N ver 1 61N Press ENT to see the next figure Fujitsu 29LV320B 2005 12 13 ACARD 4 11 17 Quick Erase Now press ESC and to see the following figure Quick Erase is to erase the data on the DVD rewriteable discs quickly 11 17 Setup Quick Erase 63 2033N User s Manual Press ENT to see the next figure Use A V to confirm Yes or No All data will be lost erase Yes After confirming Yes and pressing ENT LCD will show the message as follows Erasing disc 00 25 Quick When erasing finishes LCD will show the results as follows Quick Erase OK 07 Fail 00 4 11 18 Full Erase Now press ESC and V to see the following figure Full Erase is to erase the data on the DVD rewriteable discs completely Compared with Quick Erase Full Erase takes much more time 11 18 Setup Full Erase 64 2033N User s Manual P
46. show the message as follows Image load OK The system will ask if you want to keep editing This time use W to confirm No as shown below Continue edit next Disc No Then the system will ask if you want to burn from HDD into CD R RW or move into a partition Use A to confirm Burn as shown below Burn or Move to partition Burn After pressing LCD will show the copying information as follows Copy PO 24X 0 1 2 Trk03 25 49 2033N User s Manual When burning finishes LCD will show the results as follows Burn Complete OK 07 Now press ESC to see the following figure And press W to move the data from HDD template into a certain partition Burn or Move to partition Move After pressing V you need to select a partition into which the data will be moved Suppose we select A as shown below Select Partition A After pressing ENT LCD will show the moving information as follows Moving to P A 0 When moving finishes LCD will show the results as follows Moving to P A OK 50 2033N User s Manual If the chosen partition has contained image data the system will ask to overwrite or keep the data Press A to overwrite Image Exists Overwrite Yes After pressing LCD will show the moving information as follows Moving to P A 0 When moving finishes LCD will show the results as follows Moving to P A OK 4 10 3 Play Audio
47. ss ENT to return to the next figure Disc Counter View Press to see the following figure It is to delete the record in job Use A V to confirm Yes or No Disc Counter Del Job Counter Press W again to enter the following figure Dev means the device of DVD writer Disc Counter Del Dev Counter Press ENT to see the following figure If you want to delete the record in DVD writer 2 you can press ENT otherwise press ESC to exit Del 02 Counter Ent Del Esc Exit 81 2033N User s Manual 4 13 17 Auto Save Image Press ESC and V to see the following figure Auto Save Image can save an image file automatically into your designated partition of HDD 12 17 Adv Setup Auto Save Image Press ENT to see the following figure Auto Save Image On Press ENT to see the following figure Use A V to select a partition in which there is no image file such as C Select Partition No Image in C Press ENT to see the following figure Set Partition to C 82 2033N User s Manual Chapter 5 Troubleshooting 5 1 About LCD After powering on if there is no LCD check if the connection of power cord is firm and the environment of power outlet is normal 5 20 About Error Messages During Copy Test Compare and Verify etc if you press ESC to abort an error message will appear on LCD Abortion may cause the copy controller to hang up therefore you have to power on again If r
48. sults are not the same User ADOEtU eL E ies Cancel the job during operation 2 Connecting with a HDD All data will be lost format All data on the hard disk will be lost Confirm the formatting of hard disk Delete Image in Partition xx Confirm the deleting of data image in partition xx Format HDD s Ask if you want to format the hard disk Format HDD OK The Formatting of hard disk has been completed HDD not Format esses The hard disk hasn t been formatted yet HDD too small sss The capacity of hard disk is too small HDD too small to handle image The hard disk hasn t enough capacity to store the data image at least 5Gbytes Image Exists Overwrite There is a data image in the current partition Confirm the overwriting of data Image load Fail The image isn t successfully loaded from DVD to the hard disk Image load OK The image is successfully loaded from DVD to the hard disk No Image in Partition xx There is no data image in partition xx No Valid HDD eren The system cannot find a hard disk Partition Damage essere The partition is damaged Select HD First 0 00 ec eeececeseeseeeeneeeeees Select a formatted hard disk at first 88 2033N User s Manual Verify Hard Disk OK
Download Pdf Manuals
Related Search