SDH/SONET Frame Option User`s Manual - Electro
Contents
1. Article 5 Infringement 5 1 If and when any third party should demand injunction initiate a law suit or demand compensation for damages against the Licensee under patent right including utility model right design patent and trade mark copy right and any other rights relating to any of the Licensed Software the Licensee shall notify Yokogawa in writing to that effect without delay 5 2 In the case of the preceding Paragraph 5 1 the Licensee shall assign to Yokogawa all of the rights to defend the Licensee and to negotiate with the claiming party Furthermore the Licensee shall provide Yokogawa with necessary information or any other assistance for Yokogawa s defense and negotiation If and when such a claim should be attributable to Yokogawa subject to the written notice to Yokogawa stated in the preceding Paragraph 5 1 Yokogawa shall defend the Licensee and negotiate with the claiming party at Yokogavva s cost and expense and be responsible for the final settlement or judgment granted to the claiming party in the preceding Paragraph 5 1 5 3 When any assertion or allegation of the infringement of the third party s rights defined in Paragraph 5 1 is made or when at Yokogawa s judgment there is possibility of such assertion or allegation Yokogawa will at its own discretion take any of the following countermeasures at Yokogawa s cost and expense a To acquire the necessary right from a third party which has lawful ownership of the rig2. DAT MES UTL 00 r ER File load save File loa Parameter save Long prog load Bala load 2 With the A or V key select any of Parameter load Parameter save and SOH TOH load Popup Screen 8 4 2 IM810518801 62E 4 2 Loading a File File select 4 On the File select screen move the cursor to ir NN select the corresponding file in the File List using the 5 A or V key and press the Select or File List 5 The Load Question popup screen will appear Press the lt Yes gt or ENTER key and the selected file will be loaded File tose ENTER key 5 Press the lt Select gt or ENTER key and the Load Question popup screen will appear 4 With the A or V key move the cursor to the corresponding file in the File List File Select Screen File select 6 Press the lt Yes gt or ENTER key and the selected file will be loaded ejeq weed Sulpeo7 Dir nnt cf2 2 abg Load 71797 Question Popup Screen Note For details see Section 5 5 in the AQ2200 601 10Gbit s BERT Module s Users Manual IM810518801 01E IM810518801 62E 4 3 Appendix 1 Initial Setting Values Appendix Appendix 1 Initial Setting Values Setting Item Initial Value Remarks Screen edit mode Edit Unit STM 1 0C 3 Frame No Frame 1 screen No OC n STMn 1 A xipuaddy IM810518801 62E App
3. OC n STMn No The OC n No screen No can be displayed changed when SONET OC 1 or OC 3 has been selected as the operation mode and the STMn No screen No can be displayed changed when SDH STMO or STM1 has been selected They will not be displayed if SONET OC 192 SDH STM64 has been selected as the operation mode For details see Section 3 5 TOH SOH edit area TOH data can be displayed changed when SONET has been selected as the operation mode and the SOH data can be displayed changed when SDH has been selected For details see Section 3 5 Column button Used to select a column or consecutive columns For details see Section 3 7 4 Row button Used to select a row or consecutive rows For details see Section 3 7 4 3 4 IM810518801 62E 3 5 Explanation of Each Operation Mode 1 SONET OC 1 Mode SDH 5 Mode In SONET OC 1 and SDH 5 modes a 10 Gbps frame can be edited in 192 blocks in OC 1 unit STMO unit g Untitled Over Head Editor for 10Gbit s BERT 7 zialki Frame No Eie Edit Help 1or2 STM 0 OC 1 Frame 1 STM 0 5 1 18 No 1 to 192 1213 6 28 01 SOH TOH edit area 3 columns x 2100 00 00 9 rows 27 bytes 9100 00 00 Frame No Frame BPB0705 N o P o SDH STMO Mode Displays the frame No of the currently displayed data The frame No can be changed between 1 PPG and 2 ED To change it enter the desired frame N
4. s shape column row and All of the copy source differs from that of the paste destination the data will be pasted serially When the selected area of the copy source differs from that of the paste destination Copy source gt Paste destination If the copy data is larger than the selected paste area the copied data will be pasted starting form the beginning of the data up to the selected area size Copy destination gt Paste source If the selected paste area is larger than the copied data the copied data will be pasted repeatedly until the entire selected area is filled with the data R 3 7 Edit Operation 5 Selecting All Data Select All Operating Procedures 1 Select Edit Select All from the menu bar 2 The Edit area will be highlighted indicating that it is currently selected Hg Untitled Ower Head Editor for 10Gbit s BERT 5 x File Edit Help STM 64 0C 19 Frame 1 R Column 1 1 Z 4 6 7 8 911011111213 141151617 1819 20121122123124125126 2712829303132 01 03 Fe Fe FE FG FG FG Fe FA FE FS FS FS F6 Fe FE FG FB Fe FG FE FG FA FS FA F6 F6 FR FG n 07 OO 00 00 00 d 00 00 00 00 G 00 G d G 00 G d 00 d d d O00 O00 3 09 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 OO 04 06 SB SB SB SB SB SB SB SB SB SB SB SB SB OSB SB SB SB SB SB SB SB
5. 00 00 00 00 00 00 9100 00 00 00 00 00 00 00 00 Explanation When starting the application the initial settings are read For the initial settings see Appendix 1 For details regarding exiting the application see Section 3 6 5 Exiting the Application Exit Note To load or save a file insert the PC card adapter for CF vvith the compact flash card installed into the PC card slot on the PC IM810518801 62E 3 3 Sainpsd0 4 BE 3 4 Explanation of Each Screen SONET SDH Mode Title bar Menu A ee 4 He Untitled Over Head Editor for 10Gbit s BERT ia m 210 xi Mode display Frame STM 1 OC 3 1 Frame No OC n STMn No Column button Row button TOH SOH edit area Status bar Name Function Title bar Displays the file name and the title name of this application If no file name is set Untitled will be displayed An asterisk is displayed at the end of the file during edit For details see Section 3 9 1 Menu Displays each operation item as a command For details see Section 3 6 Status bar Displays the coordinates of the cursor position and the byte position of the data For details see Section 3 9 2 Mode display Displays the OH edit mode SONET 1 192 5 STMO STM1 5TM64 For details see Sections 3 5 Frame No The frame No can be displayed changed 1 PPG 2 ED For details see Sections 3 5
6. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7100 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8100 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 288 bytes 9100 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Frame No Frame Column No column SOH TOH edit area IM810518801 62E Displays the frame No of the currently displayed data The frame No can be changed between 1 PPG and 2 ED To change it enter the desired frame No in the Frame field and press the Enter key or select it by pressing the A and V buttons Displays the horizontal axis offset for column 1 in the SOH TOH and PayLoad edit areas The column No can be changed between 1 and 568 in the case of SOH TOH and 1 and 16 676 in the case of Payload To change it enter the desired column No in the column field and press the Enter key or select it by pressing the A and TV buttons The column No changes with movement of the scroll bar Used to edit SOH TOH data Data of 32 columns x 9 rows 288 bytes can be edited Enter data HEX format in the SOH TOH edit area directly 3 7 R 3 6 File Operation 1 Creating SDH Overhead Initial Values In
7. SB SB SB SB SB SB SB SB SB P s 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d 6 03 05 00 00 CO 00 00 oO G Oo G G oo Oo oo G G oOo oo G G OO 7 OF OS 00 G g G g g G G g G g t G g G g g G t t G g G g 2 z 04 00 00 00 00 d 00 00 00 00 G 00 G d G 00 G 00 d 00 00 d 00 d d O00 gl 06 08 OO 00 00 00 00 00 00 00 00 d 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 El 0 0 Explanation The selected area contains parts that are displayed when scrolled 3 16 IM810518801 62E 3 8 Setup Operation Help Menu Help Operating Procedures 1 Select Help About from the menu bar The About dialog box will appear Over Head Editor for 10Gbit s BERT Version 1 0 0 Copyright C 2005 Yokogawa Electric Corporation Software Japan All rights reserved YOKOGAWA 2 Click lt OK gt to return to the previous screen Explanation The About dialog box shows the version information of this application IM810518801 62E R 3 9 Explanation of Other Functions 1 Title Bar Displays the file name and the title name of this application If a file name has been set file name dat will be displayed I
8. designed for easy creation of OH patterns of SDH SONET frame for AQ2200 601 10Gbit s BERT Module and runs on Windows PC OH pattern editor for AQ2200 601 10Gbit s BERT Module Runs on Windows 98SE ME 2000 XP SP1 and enables creation of OH pattern data Created pattern data can be stored in the compact flash card The pattern data stored in the compact flash card be imported to the AQ2200 Series Frame Controller equipped with the AQ2200 601 10Gbit s BERT Module by inserting the compact flash card into the frame controller This application software is designed for easy creation of OH pattern data for AQ2200 601 10Gbit s BERT Module SDH SONET frames and runs on Windows PC Easily create OH patterns for STM 0 OC 1 STM 1 OC 3 STM 64 and OC 192 units uonduos q jeuooun 1 2 Function Overview 1 File Function The file function is used to load save a file or exit this application The file function setting items are shown below Items available for SONET SDH and Program modes e Loard the initial value of the OH pattern SDH frame Init SDH Loard the initial value of the OH pattern SONET frame Init SONET Opening a file Open Overwriting a file Save Specifying a file name and saving the data in that file Save As Exiting the application Exit The file functions can be set using the menu File menu and shortcut keys For details see Section 3 6 2 Edit Function The edit funct
9. in advance Article 8 Term This Agreement shall become effective on the date when the Licensee receives the Licensed Software and continues in effect unless or until terminated as provided herein or the Licensee ceases using the Licensed Software by itself or with Yokogawa s thirty 30 days prior written notice to the Licensee Article 9 Injunction for Use During the term of this Agreement Yokogawa may at its own discretion demand injunction against the Licensee in case that Yokogawa deems that the Licensed Software is used improperly or under severer environments other than those where Yokogawa has first approved or any other condition which Yokogawa may not permit Article 10 Termination Yokogawa at its sole discretion may terminate this Agreement without any notice or reminder to the Licensee if the Licensee violates or fails to perform this Agreement However Articles 5 6 and 11 shall survive even after the termination Article 11 Jurisdiction Any dispute controversies or differences between the parties hereto as to interpretation or execution of this Agreement shall be resolved amicably through negotiation between the parties upon the basis of mutual trust Should the parties fail to agree within ninety 90 days after notice from one of the parties to the other both parties hereby irrevocably submit to the exclusive jurisdiction of the Tokyo District Court main office in Japan for settlement of the dispute
10. is selected A to B is selected X x Y x Displays the coordinate x y of the cursor position in TOH SOH area x1 y1 x2 y2 Displays the coordinate x y of the cursor position in TOH SOH area Displays the byte position of the selected data from the beginning of the frame Displays the byte position of the selected data from the beginning of the frame One column is column x selected in TOH SOH 1 Displays the coordinate x of the selected column in TOH SOH area column x1 x2 Displays the coordinate x1 x2 of the selected column area in TOH SOH area TOW y Displays the coordinate y of the selected rovv in TOH SOH area row y1 y2 Displays the coordinate y1 y2 of the selected rovv area in TOH SOH area TOH SOH is selected 1 Select TOH Select SOH All is selected Select All Column selection is made in TOH SOH One rovv is selected in TOH SOH Rovv selection is made in TOH SOH IM810518801 62E 3 19 3 9 Explanation of Other Functions 1 In the case of A to B the contents in the Data coordinates and Byte position fields differ depending on the selection method Data coordinates Start position x1 y1 End position x2 y2 Byte position Displays the byte position of the end position Example 1 When selecting 1 1 to 5 1 in STM 1 OC 3 using the A to B selection method Data coordinates 1 1 to 5 1 Byte posit
11. or operations of the Licensed Software and the Licensee agrees on its own responsibility to solve and settle the claims and damages and to defend indemnify or hold Yokogawa totally harmless from or against any liabilities losses damages and expenses including fees for recalling the Products and reasonable attorney s fees and court costs or claims arising out of and related to the above said claims and damages Article 4 Warranty 4 1 The Licensee shall agree that the Licensed Software shall be provided to the Licensee on an as is basis when delivered If defect s such as damage to the medium of the Licensed Software attributable to Yokogawa is found Yokogawa agrees to replace free of charge any Licensed Software on condition that the defective Licensed Software shall be returned to Yokogawa s specified authorized service facility within seven 7 days after opening the Package at the Licensee s expense As the Licensed Software is provided to the Licensee on an as is basis when delivered in no event shall Yokogawa warrant that any information on or in the Licensed Software including without limitation data on computer programs and program listings be completely accurate correct reliable or the most updated 4 2 Notwithstanding the preceding Paragraph 4 1 when third party software is included in the Licensed Software the warranty period and terms and conditions that apply shall be those established by the provider of the third
12. party software 4 3 When Yokogawa decides in its own judgement that it is necessary Yokogawa may from time to time provide the Licensee with Revision upgrades and Version upgrades separately specified by Yokogawa hereinafter called Updates 4 4 Notwithstanding the preceding Paragraph 4 3 in no event shall Yokogawa provide Updates where the Licensee or any third party conducted renovation or improvement of the Licensed Software 4 5 THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF QUALITY AND PERFORMANCE WRITTEN ORAL OR IMPLIED AND ALL OTHER WARRANTIES INCLUDING ANY IMPLIED WARRANTIES OF ii IM810518801 62E Terms and Conditions of the Software License MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED BY YOKOGAWA AND ALL THIRD PARTIES LICENSING THIRD PARTY SOFTWARE TO YOKOGAWA 4 6 Correction of nonconformity in the manner and for the period of time provided above shall be the Licensee s sole and exclusive remedy for any failure of Yokogawa to comply with its obligations and shall constitute fulfillment of all liabilities of Yokogawa and any third party licensing the Third Party Software to Yokogawa including any liability for direct indirect special incidental or consequential damages whether in warranty contract tort including negligence but excluding willful conduct or gross negligence by Yokogawa or otherwise with respect to or arising out of the use of the Licensed Software
13. recorded 3 Redoing an Operation Redo Operating Procedures Explanation IM810518801 62E 1 Select Edit Redo from the menu bar The contents of the currently edited data effective just before the last undo will be restored Conditions for Redo operation Redo can only be selected just after undo is performed Redo will be invalid i e displayed in gray if edit operation is performed after undo indicating that Undo cannot be selected Recorded number of Redo operations Only one redo operation is recorded Sainpad0 4 R 3 7 Edit Operation 4 Copy amp Paste Operating Procedures 1 2 3 4 Explanation In the SOH TOH edit area select the area of the data 1 byte or more to be copied Select Edit Copy from the menu bar Select the area 1 byte or more to which the selected data is to be pasted Select Edit Paste from the menu bar The copied data will be pasted into the selected area Selecting an area Area selection items include column row and All The selected area will be highlighted e Column The specified column is selected If you click the mouse with the focus located on a column button in the SOH TOH edit area all the data present in that column will be selected If you select a column and drag the mouse or press a cursor key Shift key all the data present in the selected column area will be selected Row The specified row i
14. the lower byte data has not been entered even though the upper byte data has the characters will be displayed in blue indicating that the data cannot be confirmed If you press the Enter key with the upper byte entered the data consisting of the upper byte and the currently displayed lower byte data will be confirmed If you press the Esc key with the upper byte entered the upper byte data will be canceled Characters O to F HEX can be entered If any other characters are entered they will be ignored and the contents of the screen will not be changed Graphical explanation of data entry procedure Enter B 0 00 00 00 00 Enter A 2 00 00 00 00 00 mb 3100 00 00 00 00 4 00 00 00 00 00 5100 00 00 00 00 00 00 00 0 2 00 00 00 00 00 3 00 00 00 00 00 4 00 00 00 00 00 5100 00 00 00 00 Press the Enter key Press the Esc key 00 00 00 0 Q IM810518801 62E 3 7 Edit Operation 2 Undoing an Operation Undo Operating Procedures Explanation 1 Select Edit Undo from the menu bar The previous contents of the currently edited data vvill be restored Conditions for Undo operation Undo is effective just after data input paste and fill edit operations Undo will be invalid i e displayed in gray before edit and just after undo indicating that Undo cannot be selected Recorded number of Undo operations Only one undo operation is
15. IM810518801 62E i Terms and Conditions of the Software License Yokogawa Electric Corporation a Japanese corporation hereinafter called Yokogawa grants permission to use this Yokogawa Software Program hereinafter called the Licensed Software to the Licensee on the conditions that the Licensee agrees to the terms and conditions stipulated in Article 1 hereof You as the Licensee hereinafter called Licensee shall agree to the following terms and conditions for the software license hereinafter called the Agreement based on the use intended for the Licensed Software Please note that Yokogawa grants the Licensee permission to use the Licensed Software under the terms and conditions herein and in no event shall Yokogawa intend to sell or transfer the Licensed Software to the Licensee Licensed Software Name SDH SONET Frame Option For AQ2200 601 10Gbit s BERT Module Number of License Free Article 1 Scope Covered by these Terms and Conditions 1 1 The terms and conditions stipulated herein shall be applied to any Licensee who purchases the Licensed Software on the condition that the Licensee consents to agree to the terms and conditions stipulated herein 1 2 The Licensed Software herein shall mean and include all applicable programs and documentation without limitation all proprietary technology algorithms and know how such as a factor invariant or process contained therein Article 2 Grant of License 2 1 Yo
16. IM810518801 62E iii Terms and Conditions of the Software License Article 12 Governing Law This Agreement shall be governed by and construed in accordance with the laws of Japan The Licensee expressly agrees to waive absolutely and irrevocably and to the fullest extent permissible under applicable law any rights against the laws of Japan which it may have pursuant to the Licensee s local law Article 13 Severability In the event that any provision hereof is declared or found to be illegal by any court or tribunal of competent jurisdiction such provision shall be null and void with respect to the jurisdiction of that court or tribunal and all the remaining provisions hereof shall remain in full force and effect IM810518801 62E How to Use This Manual Structure of This Manual This user s manual consists of the following chapters IM810518801 62E Chapter 1 Title Description of Functions Setup Operating Procedures Loading Pattern Data Appendix Description This chapter provides an overview of the software and lists its main functions file and editing functions This chapter describes the system requirements of the software and lists the procedures for installing and uninstalling the software Provides the procedures for creating OH patterns using the software This chapter describes mounting to a frame controller and loading created OH pattern data Lists the initial setting values Table of
17. User s Manual Model 810518801 SDH SONET Frame Option YOKOGAVA IM 810518801 62E Yokogavva Electric Corporation 1st Edition Introduction Thank you for your purchasing of this SDH SONET Frame Option This option consists of the pattern editor application software CD ROM designed for easy creation of OH patterns of SDH SONET frame for the AQ2200 601 10Gbit s BERT Module This manual describes the functions operating procedures and handling precautions necessary to operate the OH pattern editor Before starting operation of this option thoroughly read this manual to use the product properly After reading this manual always store it in a safe place where all concerned personnel can refer to it immediately This manual is useful if the operator have forgotten proper operation steps during operation For the functions operating procedures and handling precautions of the BERT module and frame controller refer to their respective manuals Contents of the Package CD ROM for installation of the software 1 User s manual this manual 1 Notes The contents of this manual are subject to change without prior notice as a result of continuing improvements to the instrument s performance and functions The figures given in this manual may differ from those that actually appear on your screen Every effort has been made in the preparation of this manual to ensure the accuracy of its contents However shou
18. contents n FOGQUC MHOHN Auuu amad al aaa adan i Terms and Conditions of the Software License l HOW Use This Manual os bocce dacs b ah b gone V Chapter 1 Functional Description d bi OC M s l o b inn b b d d 1 1 1 2 Function VervleVV 1 2 Chapter 2 Setup Zk VSCOM Enfohlnenicec s BUDU 2 1 2 2 Installaton Uininstallatonun b nd b s 2 2 Chapter 3 Operating Procedures L 3 1 2 7 SNEEN olili tfeku a aaa Da b 3 2 2 5 SANNI h6 5DD C MOR aaa a S 3 3 34 Explanation of EaciLScTeensuuua b a A 3 4 3 5 Explanation of Each Operation Mode 3 5 20 L CODE b nb 3 8 Sr Ed ODEIO nerea a aa dd 3 12 25 0 CUD O beraliohauuse a a a 3 17 39 3 18 Chapter 4 Loading Pattern Data 4 1 Prebafallnhgeuzaa s a a ba 4 1 12 MO ACINO Taye NC ede aaa oa dates dee eae sence 4 2 Appendix Appendix 1 Initial Setting Values Appendix 1 IM810518801 62E vii Chapter1 Functional Description 1 1 Overview Major Features IM810518801 62E This application software is
19. d between 1 PPG and 2 ED To change it enter the desired frame No in the Frame field and press the Enter key or select it by pressing the A and V buttons STM 1 No OC 3 No STM 1 OC 3 Displays the screen No of the currently displayed data The screen No can be changed between 1 and 64 To change it enter the desired screen No in the STM 1 OC 3 field and press the Enter key or select it by pressing the A and V buttons SOH TOH edit area Used to edit SOH TOH data Data of 9 columns x 9 rows 81 bytes can be edited Enter data HEX format in the SOH TOH edit area directly 3 6 IM810518801 62E 3 5 Explanation of Each Operation Mode 3 SDH STM 64 Mode SONET OC 192 Mode In SDH STM 64 SONET OC 192 modes one 10 Gbps frame can be edited as it is in Frame No 1or2 Column No 1 to 545 TOH edit area 32 columns x 9 rows STM 1 OC 192 unit tg Untitled Over Head Editor for 10Gbit s BERT a L xi File Edit Help STM 64 OC 192 Frame 1 T B F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 F6 2100 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3100 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4168 9B 9B 9B 9B 9B 9B 9B 9B 9B 9B 9B 9B 9B 98 9B 9B 98 98 9B 9B 9B 9B 9B 9B 9B 9B 9B 9B 9B 9B 98 500 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20. elect File Exit from the menu bar The following alarm dialog box asking you whether to save the currently edited data will appear WARNING O o The data in the Untitled file has changed Do you want to save changes no sm 2 To save the data and exit the application click lt Yes gt To exit the application without saving the data click lt No gt To return to the edit screen without saving the data click lt Cancel gt Explanation When Yess is clicked f a file name has been set the data will be overwritten and saved e f no file name has been set the Save file selection dialog box will appear Enter a file name and click lt Save gt The data will be saved Note Commercially available CF adapter required when writing to CF card IM810518801 62E 3 11 sainped0id BulyesedQ R 3 7 Edit Operation Entering data Operating Procedures Explanation 3 12 1 n the SOH TOH edit area locate the cursor at the position where you want to enter data 2 Enter the desired character O to F When entry of the upper byte is complete the entered character will be displayed in blue 3 Next enter the desired character O to F for the lower byte When entry of the lower byte is complete the data will be confirmed and the cursor will move to the next data position 4 To continue to enter more data repeat steps 2 to 3 Data can be entered one byte at a time e f
21. endix 1
22. f no file name is set Untitled will be displayed An asterisk is displayed at the end of the file during edit When the file name is STM 1 SOH dat and the file is not currently edited 1 1 SOH dat Over Head Editor for 10Gbit s BERT When the file name is STM 1 SOH dat and the file is currently edited s T H 1 5 0 Over Head Editor for 10Gbit s BERT When no file name is set and the file is not currently edited Untitled Over Head Editor for 10Gbitrs BERT When no file name is set and the file is currently edited Untitled Over Head Editor for 10Gbit s BERT IM810518801 62E 3 9 Explanation of Other Functions 2 Status Bar Displays the coordinates of the data located at the cursor position and the byte position of that data relative position from the beginning of the data Pali 4 oTM 1_SOHdat Over Head Editor tor 10Gbit s BERT File Edit Help STM 1 0C 3 1 5TM 1a oc 3a 11 Frame IFG gh Fe 26 28 26 01 AA 2AA 00 00 00 00 00 00 00 Q 3 00 00 00 00 00 00 00 00 00 466 SB 9B FF FE FF 00 00 00 HOO 00 00 00 00 00 00 00 Q l n OO 00 00 00 00 00 00 Q T00 00 00 00 00 00 00 00 650 B00 00 00 00 00 00 00 00 Q 900 00 00 00 00 t 00 00 00 Data coordinate Byte position Byte Position Display content of the status bar Area Selection Data Coordinates sainpeddid R Only one data
23. han 00 are placed in dark colored blocks Structure of Overhead Data Block 1 F6 all 64 bytes Block 2 F6 all 64 bytes Block 3 F6 all 64 bytes Block 4 28 all 64 bytes Block 5 28 all 64 bytes Block 6 28 all 64 bytes Block 7 01 40 Block 8 41 48 Block 9 80 0 Block 10 27 00 all in this range Block 28 60 first byte only 93 remaining 63 bytes Block 29 93 all 64 bytes Block 30 93 all 64 bytes Block 31 FF all 64 bytes Block 32 FF all 64 bytes Block 33 FF all 64 bytes Block 34 81 00 all in this range IM810518801 62E 3 9 sainped0id BulyesedQ R 3 6 File Operation 3 Opening a File Open Operating Procedures 1 Select File Open from the menu bar The Open file selection dialog box will appear 2 Select the data file to be imported and click lt Open gt The imported data will be displayed in the SOH TOH edit area If you are not going to import the data click lt Cancel gt The current edit screen will reappear Explanation File format that can be imported Data in dat format can be imported file name dat When a file in unknown format is selected The following alarm dialog box will appear informing you that the data file cannot be imported Click lt OK gt to return to the current edit screen xi C workitest txt file cannot be opened drive name folder name file name file cannot be opened 4 Overvvriting a File Save Operating Proced
24. he created pattern 94 1 4 2 End IM810518801 62E indicates the section to be Sainpsd0 4 BE 3 2 Screen Structure The screen structure of this application software is shown below SONET OC 1 Edit screen Edit menu Edit Unit Edit menu Edit Unit SONET OC 3 Edit screen File menu Edit menu Init SDH Init Edit Unit SDH dialog box SONET OC 192 l Edit screen du Init SONET Init SONET dialog box Edit menu Edit menu Mode Mode File menu 5 Open file selection dialog box SDH STM 0 Edit screen File menu Save file selection Edit menu dialog box Edit Unit Edit menu Edit Unit Help menu SDH STM 1 About Edit screen About dialog box Edit menu Edit Unit Alarm occurrence Alarm dialog box SDH STM 64 Edit screen IM810518801 62E 3 3 Starting the Application 1 From the Windows Start button select Programs OHEdit OHEdit and then click it Fg Proarams EE Over HEAD Editor for 10Gbit s BERT hereafter called OHEdit will start tg Untitled Over Head Editor for 10Gbit s BERT iol File Edit Help STM 1 OC 3 Frame STM 1 0C 3 1 1 F6 F6 28 28 28 01 AA AA 2100 00 00 00 00 00 00 00 00 3 00 00 00 00 00 00 00 00 00 4168 9B 9B FF FF FF 00 00 00 500 00 00 00 00 00 00 00 00 6 00 00 00 00 00 00 00 00 00 7100 00 00 00 00 00 00 00 00 3 00 00 00
25. ht so that the Licensee will be able to continue to use the Licensed Software b To replace the Licensed Software with an alternative one which avoids the infringement or To remodel the Licensed Software so that the Licensed Software can avoid the infringement of such third party s right 5 4 If and when Yokogawa fails to take either of the countermeasures as set forth in the preceding subparagraphs of Paragraph 5 3 Yokogawa shall indemnify the Licensee only by paying back the price amount of the Licensed Software which Yokogawa has received from the Licensee THE FOREGOING PARAGRAPHS STATE THE ENTIRE LIABILITY OF YOKOGAWA AND ANY THIRD PARTY LICENSING THIRD PARTY SOFTWARE TO YOKOGAWA WITH RESPECT TO INFRINGEMENT OF THE INTELLECTUAL PROPERTY RIGHTS INCLUDING BUT NOT LIMITED TO PATENT AND COPYRIGHT Article 6 Liabilities 6 1 If and when the Licensee should incur any damage relating to or arising out of the Licensed Software or service that Yokogawa has provided to the Licensee under the conditions herein due to a reason attributable to Yokogawa Yokogawa shall take actions in accordance with this Agreement However in no event shall Yokogawa be liable or responsible for any special incidental consequential and or indirect damage whether in contract warranty tort negligence strict liability or otherwise including without limitation loss of operational profit or revenue loss of use of the Licensed Software or any associated products
26. icensed Software may include a software program licensed for re use by a third party hereinafter called Third Party Software which may include any software program from affiliates of Yokogawa made or coded by themselves In the case that Yokogawa is granted permission to sublicense to third parties by any licensors sub licensor of the Third Party Software pursuant to different terms and conditions than those stipulated in this Agreement the Licensee shall observe such terms and conditions of which Yokogawa notifies the Licensee in writing separately 2 8 In no event shall the Licensee modify remove or delete a copyright notice of Yokogawa and its licenser contained in the Licensed Software including any copy thereof Article 3 Restriction of Specific Use 3 1 The Licensed Software shall not be intended specifically to be designed developed constructed manufactured distributed or maintained for the purpose of the following events a Operation of any aviation vessel or support of those operations from the ground b Operation of nuclear products and or facilities c Operation of nuclear weapons and or chemical weapons and or biological weapons or d Operation of medical instrumentation directly utilized for humankind or the human body 3 2 Even if the Licensee uses the Licensed Software for the purposes in the preceding Paragraph 3 1 Yokogawa has no liability to or responsibility for any demand or damage arising out of the use
27. ion 257 Example 2 When selecting 5 1 to 1 1 in STM 1 OC 3 using the A to B selection method Data coordinates 5 1 to 1 1 Byte position 1 2 n the case of column rovv selection the content in the Data coordinates field differs depending on the selection method Data coordinates For column Start position x1 End position x2 For row Start position y1 End position y2 Example 1 When selecting columns 1 to 5 in STM 1 OC 3 Data coordinates PaylLoad columns 1 to 5 Example 2 When selecting columns 5 to 1 in STM 1 OC 3 Data coordinates PayLoad columns 5 to 1 In the above examples the selected area is the same though the display contents differ Therefore file operation and copy amp paste operation have the same results 3 20 IM810518801 62E 3 Context Menu IM810518801 62E 3 9 Explanation of Other Functions If you right click with the cursor located in an edit area a context menu will appear It contains the same items as the Edit menu Unda trita Beda Shift HEt E Copy C Paste triti Select All Sir Edit Unit F sainpeddid R Chapter 4 Loading Pattern Data 4 1 Preparation 1 Installing the Compact Flash Card Install the compact flash card containing the created pattern data into the AQ2201 AQ2202 Frame Controller equipped with the AQ2200 601 10Gbit s BERT Module Note The compact flash card can be inserted removed e
28. ion is used to create edit OH pattern data The edit function setting items are shown below Undoing an operation Undo Redoing an operation Redo Copy Copy Paste Paste Selecting all SOH TOH Select All Edit mode Edit Unit The edit functions can be set using the menu Edit menu and shortcut keys except for Select XX For details see Section 3 7 1 2 IM810518801 62E Chapter 2 Setup B System Environment Hardware Requirements This software runs under the following environment Item Condition Personal computer CPU Pentium IIl 500MHz or higher Hard disk capacity 500MB or more recommended Memory capacity 256MB or higher CD ROM drive Monitor Resolution 800 x 600 dots or higher 256 colors or higher Operating system English Japanese version 1 Windows 98SE Windows ME Windows 2000 Windows XP SP1 1 If this application software is installed on Windows PC Japanese version texts will be displayed in Japanese Note This manual explains the operating method when this application software is used with English Windows 2000 IM810518801 62E 2 1 z Installation Uninstallation Operating Procedures Installation Uninstallation Explanation 1 Start the PC 2 Insert the attached CD ROM containing this application software into the CD ROM drive on the PC 3 Double click the Setup Exe icon in the OHEdit folder of the CD ROM drive PatiEdit msi The installer will start and set
29. it SDH Operating Procedures 1 Choose File gt Init SDH 2 SDH overhead initial values are created Explanation SDH overhead initial value data file e sdh_init dat Created during installation for details see section 2 2 below SDH overhead initial value data e Described below in units of 64 byte blocks Each square in the diagram represents a block 64 bytes of data Values other than 00 are placed in dark colored blocks Structure of Overhead Data Block 1 F6 all 64 bytes Block 2 F6 all 64 bytes Block 3 F6 all 64 bytes Block 4 28 all 64 bytes Block 5 28 all 64 bytes Block 6 28 all 64 bytes Block 7 01 40 Block 8 AA Block 9 AA Block 10 27 00 all in this range Block 28 68 first byte only 9B remaining 63 bytes Block 29 9B all 64 bytes Block 30 9B all 64 bytes Block 31 FF all 64 bytes Block 32 FF all 64 bytes Block 33 FF all 64 bytes Block 34 81 00 all in this range 3 8 IM810518801 62E 3 6 File Operation 2 Creating SONET Overhead Initial Values Init SONET Operating Procedures 1 Choose File gt Init SONET from the menu 2 SONET overhead initial values are created Explanation SONET overhead initial value data file e sonet init dat Created during installation for details see section 2 2 below SONET overhead initial value data e Described below in units of 64 byte blocks Each square in the diagram represents a block 64 bytes of data Values other t
30. kogawa grants the Licensee for the purpose of single use non exclusive and non transferable license of the Licensed Software with the license fee separately agreed upon by both parties 2 2 The Licensee is unless otherwise agreed in writing by Yokogawa not entitled to copy change sell distribute transfer or sublicense the Licensed Software 2 3 The Licensed Software shall not be copied in whole or in part except for keeping one 1 copy for back up purposes The Licensee shall secure or supervise the copy of the Licensed Software by the Licensee itself with great strict and due care 2 4 In no event shall the Licensee dump reverse assemble reverse compile or reverse engineer the Licensed Software so that the Licensee may translate the Licensed Software into other programs or change it into a man readable form from the source code of the Licensed Software Unless otherwise separately agreed by Yokogawa Yokogawa shall not provide the Licensee the source code for the Licensed Software 2 5 The Licensed Software and its related documentation shall be the proprietary property or trade secret of Yokogawa or a third party which grants Yokogawa the rights In no event shall the Licensee be transferred leased sublicensed or assigned any rights relating to the Licensed Software 2 6 Yokogawa may use or add copy protection in or onto the Licensed Software In no event shall the Licensee remove or attempt to remove such copy protection 2 7 The L
31. ld you have any questions or find any errors please contact your nearest YOKOGAWVA dealer Copying or reproducing all or any part of the contents of this manual without the permission of Yokogawa Electric Corporation is strictly prohibited This software can be installed on more than one computer However program patterns created by this software can run only on the AQ2200 601 10Gbit s BERT Module to which the option has been implemented Transfer or lending of this software to any third party is prohibited Yokogawa Electric Corporation provides no guarantees other than for physical deficiencies found on the original disk upon opening the product package Yokogawa Electric Corporation shall not be held responsible by any party for any losses or damage direct or indirect caused by the use or any unpredictable defect of the product Trademarks Microsoft MS DOS and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Adobe and Acrobat are trademarks of Adobe Systems Incorporated For purposes of this manual the TM and symbols do not accompany their respective trademark names or registered trademark names Other product names are trademarks or registered trademarks of their respective holders Revisions 151 Edition August 2005 1st Edition August 2005 YK All Rights Reserved Copyright 2005 Yokogawa Electric Corporation
32. o in the Frame field and press the Enter key or select it by pressing the A and V buttons STM O No OC 1 No STM 0 OC 1 SOH TOH edit area IM810518801 62E Displays the screen No of the currently displayed data The screen No can be changed between 1 and 192 To change it enter the desired screen No in the S TM 0 OC 1 field and press the Enter key or select it by pressing the A and V buttons Used to edit SOH TOH data Data of 3 columns x 9 rows 27 bytes can be edited Enter data HEX format in the SOH TOH edit area directly R 3 5 Explanation of Each Operation Mode 2 SDH STM 1 mode SONET OC 3 mode In SDH STM 1 and SONET OC 3 modes a 10 Gbps frame can be edited in 64 blocks in STM 1 unit OC 3 unit tg Untitled Over Head Editor for 10Gbit s BERT B L xj Frame No File Edit Help 1or2 STM 1 OC 3 Frame 1 STM 0 STM 1 OC 3 i 05 OC 3 No 1 to 64 1 l 6 F6 F6 28 28 28 01 AA AA 2100 00 00 00 00 00 00 00 00 3100 00 00 00 00 00 00 00 00 4168 9B 9B FF FF FF 00 00 00 5100 00 00 00 00 00 00 00 00 6100 00 00 00 00 00 00 00 00 SOH TOH edit area 7100 00 00 00 00 00 00 00 00 9 columns x 8100 00 00 00 00 00 00 00 00 9 rows 81 bytes 9100 00 00 00 00 00 00 00 00 SDH STM1 Mode Frame No Frame Displays the frame No of the currently displayed data The frame No can be change
33. or equipment cost of capital loss or cost of interruption of the Licensee s business substitute equipment facilities or services downtime costs delays and loss of business information or claims of customers of Licensee or other third parties for such or other damages Even if Yokogawa is liable or responsible for the damages attributable to Yokogawa and to the extent of this Article 6 Yokogawa s liability for the Licensee s damage shall not exceed the price amount of the Licensed Software or service fee which Yokogawa has received Please note that Yokogawa shall be released or discharged from part or all of the liability under this Agreement if the Licensee modifies remodels combines with other software or products or causes any deviation from the basic specifications or functional specifications without Yokogavva s prior written consent 6 2 All causes of action against Yokogawa arising out of or relating to this Agreement or the performance or breach hereof shall expire unless Yokogawa is notified of the claim within one 1 year of its occurrence 6 3 In no event regardless of cause shall Yokogawa assume responsibility for or be liable for penalties or penalty clauses in any contracts between the Licensee and its customers Article 7 Limit of Export Unless otherwise agreed by Yokogawa the Licensee shall not directly or indirectly export or transfer the Licensed Software to any countries other than those where Yokogawa permits export
34. s selected If you click the mouse with the focus located on a row button at the left of the SOH TOH edit area all the data present in that row will be selected If you select a row and drag the mouse or press a cursor key Shift key all the data present in the selected row area will be selected All The SOH TOH edit area is selected For details see Section 3 7 5 Canceling the selected area If you press the Esc key while an area is currently selected the selected area will be cancelled and only the data at the selected position will be selected If you click the mouse while an area is currently selected the selected area will be cancelled and only the data at the clicked position will be selected The selected area will also be cancelled if the focus moves into another edit area Copy operation 3 14 If you execute a new copy after executing a copy the old copied data will be deleted The data inside the copy area will be kept irrespective of the selected area s shape column row and All IM810518801 62E IM810518801 62E 3 7 Edit Operation Paste operation When no data area has been selected If only one data is specified without selecting an area the content of the copied data will be pasted starting from the specified position up to the copy size When a data area has been selected If a data area has been selected the copied data will be pasted into that area If the selected area
35. up will begin 4 Follow the instructions displayed on the screen to perform installation 5 When installation is complete a shortcut to the following submenu will be created Windows Start button Programs OHEdit OHEdit 1 From the Windows Start button select Settings Control Panel Add or Remove Programs 2 Select OHEdit from the program list and click Remove 3 Follow the instructions displayed on the screen Installation folder This application software will be installed in the following folder C Program Files YOKOGAWA OHEdit Changing the installation folder The installation folder can be changed while Select Installation Folder is displayed during installation Installation files The following files will be installed OHEdit exe Executable file e sonet_init dat InitialOH data file for SONET sdh_init dat lInitialOH data file for SDH IM810518801 62E Chapter 3 Operating Procedures 3 1 Flow of Operation Operation Flow Editing a Pattern Use the Edit and Search menus to edit a pattern Data input 33 7 1 Selection Select All 43 7 5 Copy amp paste Copy Paste 33 7 4 Etc Saving a Pattern Use the File menu to save the edited pattern to the CF Save Save Save As 3 6 Loading a Pattern Install the CF to the frame controller equipped with the 10GBERT Module and load t
36. ures VVhen a file name has been set for the currently edited data 1 Select File Save from the menu bar The data will be overwritten and the current edit screen will reappear lt When no file name has been set for the currently edited data gt 1 Select File Save from the menu bar The Save file selection dialog box will appear 2 Enter a file name and click lt Save gt The data will be saved to the specified file and the current edit screen will reappear If you are not going to save the data click lt Cancel gt The current edit screen will reappear Explanation File save format The data is saved in dat format file name dat 3 10 IM810518801 62E 3 6 File Operation 5 Specifying a File Name and Saving the Data in That File Save As Operating Procedures 1 Select File SaveAs from the menu bar The Save file selection dialog box will appear 2 Enter a file name and click lt Save gt The data will be saved to the specified file and the current edit screen will reappear If you are not going to save the data click lt Cancel gt The current edit screen will reappear Explanation File save format The data is saved in dat format file name dat 6 Exiting the Application Exit Operating Procedures VVhen the data has been saved 1 Select File Exit from the menu bar The application vvill be exited VVhen the data has not been saved 1 S
37. ven if the power to the frame controller is currently ON However do not remove it while the BERT application is in progress 2 Starting the BERT Application Press the APPLI key on the front panel of the frame controller to start the BERT application Note For details see Section 5 4 in the AQ2200 601 10Gbit s BERT Module s Users Manual IM810518801 01E IM810518801 62E 4 1 ejeq gt 4 2 Loading a File Load a pattern data file stored in the compact flash card to the BERT Module Operating Procedures BERT APPLICATION 00 00 00 10 Leg 1 With the CHAN or FRAME key select UTL mn the current module 2 With the A V 14 or gt key move the cursor so that File load save becomes the 777 mes current parameter and press the ENTER key 3 The File load save popup screen will appear PPG ED DAT HES UTL a With the A or V key move the cursor to any Logging cou of Parameter load Parameter save and Long Coe 1sec prog load and press the lt OK gt or ENTER period kuza Signal key and the File select screen will appear ALT Pee Erron Eel 1 Move the cursor to File load save and press the ENTER key BERT APPLICATION 3 Press the lt OK gt or ENTER key and the 00 00 00 Loz File select screen will appear Err on on Current ii PPG ED
Download Pdf Manuals
Related Search