210 user manual
Contents
1. Jl Operation manual Weight indicator model 210 Industrivag Teknik KEYPAD FUNCTIONS The model 210 is equipped with a 22 key keypad The keypad is used to enter commands and data into the instrument This section describes each key along with its normal function It is helpful to refer to the actual instrument while reading this section ZERO mud NET GROGE TARE Es E3 Ia g lkb oz kg EH COUNT f TIME DA EH SAMPLE DATE EA laa MA Industivag Teknik www ivtind se Model 210 The membrane Keypad is not to be operated with pointed objects Damage to keypad resulting from this practice is NOT covered under warranty ON OFF KEY This key performs two functions e Pressing it when the indicator is off will apply power to the instrument e If the indicator is already on pressing this key will turn the indicator off ZERO KEY This key causes an immediate zeroing of the weight display up to the selected limit of 4 or 100 of the scale s capacity Note that this selection is made during the setup and calibration of the instrument If the weight reading is unstable the command will be ignored Industrivag Teknik Kinnared Nydal 523 97 Ulricehamn Tel 46 32140170 Fax 46 32140233 TARE KEY with arrow This key is a dual function key Pressing the TARE key alone will store the current gross weight as the new tare weight and cause the weight display to change to the net weight display mode Pre2. RESET key the display will show PSEt 1 and the PWC1 annunciator will flash Press the ENTER key the display will snow the currently stored value for the number 1 preset weight comparator If the value displayed is acceptable press the ENTER Key otherwise use the numeric keys to enter the new preset value and press the ENTER key Repeat the steps above for preset weight comparator 2 and 3 Checkweigher If the checkweigher feature was selected and the PRESET key pressed the ACCEPT and UNDER annunciators will flash and the preset value for the minimum acceptable weight will be displayed Press the ENTER key if the displayed value is correct or use the numeric keys and enter a new value and press the ENTER key The ACCEPT and OVER annunciators will now flash and the display will show the minimum value of weight over the accepted range As before if the value shown is correct press the ENTER key If the value is incorrect enter the new value and press the ENTER key to save it Note that both the preset weight comparators and checkweigher functions operate on the absolute value of the weight ignoring the polarity Industrivag Teknik Kinnared Nydal 523 97 Ulricehamn Tel 46 32140170 Fax 46 32140233 PRINT KEY Pressing this key will add the displayed gross or net weight or piece count to the associated accumulator and initiate the transmission of weight and other data via the selected printer output port Note tha
3. e then press the ENTER key Press the ASTERISK key to abort the input operation To exit the count function and display weight press the NET GROSS key Industrivag Teknik Kinnared Nydal 523 97 Ulricehamn Tel 46 32140170 Fax 46 32140233 TIME DATE KEY This key is used to enter the clock mode to program the time date and consecutive number Pressing the TIME DATE key will enter the clock mode with the 210 displaying HOUR With the display showing HOUR press the ENTER key If the time displayed is correct press the ENTER key If the time displayed is incorrect use the numeric keys to enter the correct time and press the ENTER key The display will Show DATE Press the ENTER key If the date displayed is correct press the ENTER key If the date displayed is incorrect use the numeric keys to enter the correct date and press the ENTER key The display will show CnC n Press the ENTER key If the consecutive number displayed is correct press the ENTER key to resume normal operation If the consecutive number displayed is incorrect use the numeric keys to enter the correct consecutive number up to 6 digits and press the ENTER key to resume normal operation PRESET KEY This key is used to enter the weight values for the three preset weight comparators or for the checkweigher feature depending on which feature was selected during setup and calibration Preset weight comparator Press the P
4. he weight value stored as preset number 3 in the preset weight comparator feature T The T tons annunciator is located to the right of the weight display and is turned on to show that the displayed weight unit is tons g The g grams annunciator is located to the right of the weight display and is turned on to show that the displayed weight unit is grams Ib The Ib pounds annunciator is located to the right of the weight display and is turned on to show that the displayed weight unit is pounds 02 The oz ounces annunciator is located to the right of the weight display and is turned on to show that the displayed weight unit is ounces kg The kg kilograms annunciator is located to the right of the weight display and is turned on to show that the displayed weight unit is kilograms t The t tonnes metric tons annunciator is located to the right of the weight display and is turned on to show that the displayed weight unit is tonnes Industrivag Teknik Kinnared Nydal 523 97 Ulricehamn Tel 46 32140170 Fax 46 32140233
5. out one second e All horizontal segments will turn on e All vertikal segments and decimal points will turn on e All annunciators will turn on e All display elements off e The model number and the software version e Calibration numbers C1 to C4 This combination is used to change the selected print ticket format The display will show Prt Press the ENTER key to show the current value If the setting displayed is acceptable press the ENTER key again to save it Otherwise use the numeric keys to enter the new setting then press the ENTER key to save it Allowable values are O Print tab settings 1 VisualPrintformat1 2 VisualPrint format 2 In addition to using the ASTERISK PRINT key combination to change the print ticket format the operator can change the ticket format by pressing the desired format number 0 1 or 2 followed by pressing the PRINT key Industrivag Teknik Kinnared Nydal 523 97 Ulricehamn Tel 46 32140170 Fax 46 32140233 Annunciators Annunciators are turned on to indicate that the display is in the mode corresponding to the annunciator label or that the status indicated by the label is active The annunciators flash on and off to indicate that the 210 is waiting for an input from the keypad for the mode indicated by the flashing annunciator ZERO The ZERO annunciator is turned on to indicate that the weight is within VY division of the center of zero STABLE The STABLE annuncia
6. ssing this key after entering a numeric value will cause the value entered to be accepted as the new tare weight Note Tare weights equal to or greater than scale capacity cannot be entered In addition the keypad tare weight division value must be the same as the scale division value ss NET GROSS KEY This key is used to toggle between net and gross weight modes The selected mode is indicated by turning on the appropriate annunciator on the display Note that if no valid tare weight has been entered pressing this key will cause a momentary notare display error and the indicator will remain in the gross weight mode TARE KEY with weight symbol Pressing this key will display the current tare weight for three seconds UNITS KEY This key is used to select the units in which the weight is to be displayed The available units of measure are enabled or disabled in setup If only one unit of measure is enabled the command is ignored COUNT SAMPLE KEY This key performs two functions The first time it is pressed the indicator will count unless piece weight is 0 The second time it is pressed or if pcwt 0 on the first press it will show the prompt ADD 5 on the display Continued pressing of the key will toggle between the ADD 5 10 25 50 75 prompts to select a sample size When desired sample size is displayed press the ENTER key or with ADD Xx displayed using the numeric keypad key in any desired sample valu
7. t the indicator will not respond to the print command unless the weight display is stable If displaying gross weight the only weight printed is gross weigNt If displaying net weight the gross tare and net weights are printed ASTERISK This key is used in conjunction with other keys to access additional indicator features These features and their associated key combinations are as follows NET GROSS This combination will display the Net accumulator NET GROSS This combination will print the Net accumulator NET GROSS soe 2 This combination will clear the Net accumulator NET GROSS This combination will display the Gross accumulator NET GROSS cs can This combination will print the Gross accumulator NET GROSS COUNT SAMPLE TA 2 This combination will clear the Gross accumulator This combination will display the Piece count accumulator COUNT SAMPLE PRINT This combination will print the Piece count accumulator COUNT SAMPLE Oe 2 This combination will clear the Piece count accumulator Industrivag Teknik Kinnared Nydal 523 97 Ulricehamn Tel 46 32140170 Fax 46 32140233 This combination will enter the Test mode The Test mode is used to conduct a test of all display elements The test consists of five cycles each lasting ab
8. tor is identified with two small triangle shapes and is turned on when the weight display is stable NET The NET annunciator is turned on to show that the displayed weight is the net weight gross weight less tare weight GROSS The GROSS annunciator is turned on to show that the displayed weight is the gross weight TARE The TARE annunciator is turned on to show that the displayed weight is the tare weight LO BAT The LO BAT annunciator is used with the battery operation and will turn on to indicate that the battery has less than one hour useful life before recharging will be required UNDER PWC1 This annunciator is used to signal that the displayed weight is either less than the minimum value of acceptable weight used in the checkweigher feature or equal to or greater than the weight value stored as preset number 1 in the preset weight comparator feature ACCEPT PWC2 This annunciator is used to signal that the displayed weight is either within the acceptable weight limits used in the checkweigher feature or equal to or greater than the weight value stored as preset number 2 in the preset weight comparator feature Industrivag Teknik Kinnared Nydal 523 97 Ulricehamn Tel 46 32140170 Fax 46 32140233 OVER PWC3 This annunciator is used to signal that the displayed weight is either equal to or greater than than the maximum value of acceptable weight used in the checkweigher feature or equal to or greater than t
Download Pdf Manuals
Related Search