USER MANUAL - Kramer Electronics
Contents
1. Use the following IP address IP address m2 1 2 Subnet mask 255 255 255 0 Default gateway iru Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server E Validate settings upon exit Figure 11 Internet Protocol Properties Window 7 Click OK 8 Click Close Connecting the Ethernet Port via a Network Hub or Switch You can connect the Ethernet port of the VS 44HDx to the Ethernet port on a network hub or using a straight through cable with RJ 45 connectors Control Configuration via the Ethernet Port To control several units via Ethernet connect the Master unit Device 1 via the Ethernet port to the Ethernet port of your PC Use your PC provide initial configuration of the settings see Section 5 9 VS 44HDxI Connecting the VS 44HDxI 5 10 Controlling via the REMOTE Connector You can force the routing of one of the four inputs to any of the four outputs by remote control To do so connect the appropriate REMOTE input terminal block connector pins to a contact closure switch In the dual link mode you can force the routing of any of the two inputs to any of the two outputs To route input 1 to output 4 as the example in Figure 12 illustrates momentarily touch firstly output 4 to the ground and then secondly input 1 to the ground m To route INPUT 1 to OUTPUT 4 _ Stage 1 Temporarily connect OUTPUT PIN 42. Unpack the equipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual Go to http www kramerelectronics com support product_downloads asp to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate Achieving the Best Performance To achieve the best performance Use only good quality connection cables we recommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables Do not secure the cables in tight bundles or roll the slack into tight coils Avoid interference from neighboring electrical appliances that may adversely influence signal quality Position your Kramer VS 44HDxI away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building 2 2 2 3 VS 44HDxl Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the power cord that is supplied with the unit Warning Do not open the unit High voltages can cause electrical shock Servicing by qualified personnel only Warning Disconnect the power and unplug the unit from the wall before installing Recycling Kramer
3. any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics willdo Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper o
4. 1 to output 7 using the front panel buttons the switcher sends HEX code 41 81 87 83 to the PC When the PC sends one of the commands in this group to the switcher if the instruction is valid the switcher replies by sending the same four bytes to the PC that it received except for the first byte where the DESTINATION bit is set high NOTE 3 SETUP 0 is the present setting SETUP 1 and higher are the settings saved in the switcher s memory i e those used for Store and Recall NOTE 4 The reply to a REQUEST instruction is as follows the same instruction and INPUT codes that were sent are returned and the OUTPUT is assigned the value of the requested parameter The replies to instructions 10 and 11 are according to the definitions in instructions 7 and 8 respectively For example if the present status of machine number 5 is breakaway setting then the reply to HEX code 0B 80 80 85 is HEX code 4B 80 81 85 NOTE 6 If INPUT is set to 127 for these instructions and if the function is defined on this machine it replies with OUTPUT 1 If the function is not defined then the machine replies with OUTPUT 0 or with an error invalid instruction code If the INPUT is set to 126 for these instructions then if possible the machine returns the current setting of this function even in the case that the function is not defined For example for a video switcher that always switches during the VIS of input 1 and its VIS setti
5. 6 Crossed Cable RS 232 Connection Figure 7 Straight Cable RS 232 Connection with a Null Modem Adapter Figure 8 Local Area Connection Properties Window Figure 9 Internet Protocol Version 4 Properties Window Figure 10 Internet Protocol Version 6 Properties Window Figure 11 Internet Protocol Properties Window Figure 12 Using the REMOTE Connector our WWNDND Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront video audio presentation and broadcasting professionals on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Products Congratulations on purchasing your Kramer VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher which is ideal for the following typical applications e Broadcasting and production studios e Presentation applications 2 1 Getting Started We recommend that you
6. 7 segment display no longer flashes The TAKE button illuminates To confirm several actions in CONFIRM mode do the following 1 Press each OUT IN combination in sequence The 7 segment display flashes 2 Press the TAKE button to confirm all the actions The 7 segment display no longer flashes The TAKE button illuminates VS 44HDxI Operating the VS 44HDxI 6 3 Storing Recalling Input Output Configurations You can store and recall up to eight setup configurations using the four INPUT buttons and the four OUTPUT buttons The setup also includes the working mode 6 3 1 Storing an Input Output Configuration To store the current status in memory do the following 1 Set the working mode see Section 5 3 2 Press the STO button The STO button illuminates 3 Press one of the 8 INPUT OUTPUT buttons this is the setup in which the current status is stored The selected INPUT OUTPUT button illuminates in blue The memory stores the data at that reference To confirm the setup press the INPUT OUTPUT button again To cancel the setup press the STO button once again 6 3 2 Recalling an Input Output Configuration To recall an input output configuration do the following 1 Press the RCL button The RCL button illuminates 2 Press the appropriate INPUT OUTPUT button the button corresponding to the setup That setup configuration flashes in the 7 segment display The memory recalls the stored data from that
7. require no user confirmation However no protection is offered against changing an action in error In the CONFIRM mode e You can key in several actions and then confirm them by pressing the TAKE button to simultaneously activate the multiple switches e Every action requires user confirmation protecting against erroneous switching e Execution is delayed until the user confirms the action Note that after ten seconds the VS 44HDxI goes to standby mode and the buttons and the 7 segment display illuminates less brightly 6 2 1 6 2 2 Toggling between the AT ONCE and CONFIRM Modes To toggle between the AT ONCE and CONFIRM modes do the following 1 Press the dim TAKE button to toggle from the AT ONCE mode in which the TAKE button is dim to the CONFIRM mode in which the TAKE button illuminates Actions now require user confirmation and the TAKE button illuminates 2 Press the illuminated TAKE button to toggle from the CONFIRM mode back to the AT ONCE mode Actions no longer require user confirmation and the TAKE button no longer illuminates Confirming a Switching Action To confirm a switching action in CONFIRM mode where the TAKE button is illuminated do the following When operating the machine in the CONFIRM mode the remote RS 232 control is disabled 1 Press an OUT IN combination The 7 segment display flashes the timeout lasts for 10 seconds 2 Press the TAKE button to confirm the action The
8. via the RS 485 port from a distance of up to 1200m 3900ft using any device equipped with an RS 485 port for example a PC For successful communication you must set the RS 485 machine number and bus termination To connect a device with a RS 485 port to the VS 44HDxl e Connect the A pin on the RS 485 port of the PC to the A pin on the RS 485 port on the rear panel of the VS 44HDxl e Connect the B pin on the RS 485 port of the PC to the B pin on the RS 485 port on the rear panel of the VS 44HDxl e Connect the G pin on the RS 485 port of the PC to the G pin on the RS 485 port on the rear panel of the VS 44HDxI Performing a Factory Reset Press and hold the input buttons 1 2 and 3 simultaneously for 3 seconds until the three buttons flash to reset the machine to its default values Switching Genlocked Video Signals The genlock feature lets you switch genlocked video signals according to timing of the GENLOCK reference input According to SMPTE RP 168 The sources must be genlocked to the GENLOCK input in order to switch cleanly e Connect the GENLOCK cable If the HD input signal that is connected is one of the following it is necessary to set it up as follows The unit automatically detects when SD SDI inputs are used e 1080i 60Hz press and hold INPUT 1 button for 3 seconds The button flashes to indicate that the set up was completed If a change is made to the resolution or refresh rate The button d
9. 4HDxl Connecting the RS 232 Port You can connect to the unit via a crossed RS 232 connection using for example a PC A crossed cable or null modem is required as shown in method A and B respectively If a shielded cable is used connect the shield to pin 5 Method A Figure 6 Connect the RS 232 9 pin D sub port on the unit via a crossed cable only pin 2 to pin 3 pin 3 to pin 2 and pin 5 to pin 5 need be connected to the RS 232 9 pin D sub port on the PC Note There is no need to connect any other pins Figure 6 Crossed Cable RS 232 Connection Hardware flow control is not required for this unit In the rare case where a controller requires hardware flow control short pin 1 to 7 and 8 and pin 4 to 6 on the controller side Method B Figure 7 Connect the RS 232 9 pin D sub port on the unit via a straight flat cable to the null modem adapter and connect the null modem adapter to the RS 232 9 pin D sub port on the PC The straight cable usually contains all nine wires for a full connection of the D sub connector Because the null modem adapter which already includes the flow control jumpering described in Method A above only requires pins 2 3 and 5 to be connected you are free to decide whether to connect only these 3 pins or all 9 pins Figure 7 Straight Cable RS 232 Connection with a Null Modem Adapter 5 6 5 7 5 8 Connecting a PC or Controller to the RS 485 Port You can operate the VS 44HDXxl
10. ACHINE 1 Video machine name For names 2 Audio machine name 0 Request first 4 digits 3 Video software version 1 Request first suffix 4 Audio software version 2 Request second suffix 5 RS 422 controller 3 Request third suffix name 10 Request first prefix 6 RS 422 controller 11 Request second prefix version 12 Request third prefix 7 Remote control name 8 Remote software For versions version 0 main board 9 Protocol 2000 revision or the number of external board 10 Control data machine name 11 Control data software version 62 DEFINE MACHINE 1 Number of inputs 1 For video 2 Number of outputs 2 For audio 3 Number of setups 3 For SDI 4 For remote panel 5 For RS 422 controller 6 For control data i VS 44HDxIl Protocol 2000 VS 44HDxI NOTES on the above table NOTE 1 When the master switcher is reset e g when it is turned on the reset code is sent to the PC If this code is sent to a switcher it resets according to the present power down settings NOTE 2 These are bi directional definitions If the switcher receives the code it performs the instruction If the instruction is performed due to a keystroke operation on the front panel then these codes are sent For example if the PC sends HEX code 01 85 88 83 then the switcher machine 3 switches input 5 to output 8 If the user switches input
11. AT ONCE mode see Section 6 2 do the following For details of how to route an input to an output using the REMOTE connector see Section 5 10 1 Press an OUTPUT button either 1 2 3 4 or ALL The selected OUTPUT button illuminates brightly as does the 7 segment display For immediate switching press an INPUT button either 1 2 3 4 or OFF The selected input switches to the selected output and that input button VS 44HDxI Operating the VS 44HDxI 6 1 2 6 2 illuminates brightly The digits displayed in the 7 segment display change as appropriate Switching OUT IN Combinations in the Dual Link Mode To switch an input to an output in the dual link mode via the front panel buttons in the AT ONCE mode see Section 6 2 do the following 1 Press an OUTPUT button either 1 2 or ALL The selected OUTPUT button illuminates brightly as does the 7 segment display 2 Press an INPUT button either 1 2 or OFF The selected input switches to the selected output and that input button illuminates brightly The digits displayed in the 7 segment display change as appropriate Confirming Settings Choose to work in the AT ONCE or the CONFIRM mode When the VS 44HDxI operates in the AT ONCE mode pressing an OUT IN combination implements the switch immediately In the CONFIRM mode the TAKE button must be pressed to authorize the switch In the AT ONCE mode you save time as execution is immediate and actions
12. HDxtl in the dual link mode do the following 1 Connect one or both of the SDI sources to the INPUT DUAL LINK BNC connectors For example a dual link HD SD SDI camera to DUAL LINK 1 inputs 1 and 2 and a dual link 3G HD video server to DUAL LINK 2 inputs 3 and 4 2 Connect the SDI OUTPUT BNC connectors to one or both SDI acceptors For example OUTPUT DUAL LINK 1 outputs 1 and 2 to a dual link preview display and OUTPUT DUAL LINK 2 outputs 3 and 4 to a dual link HD SDI mixer 3 Set the DIP switches see Section 5 3 4 If required connect not shown in Figure 3 Agenlock source to the GENLOCK BNC connector The LOOP BNC connector to the GENLOCK connector of the next unit in the line and release the TERM button for looping Pushed in terminates the input Release when the input extends to another unit 5 Connect a PC and or controller if required to the RS 232 port see Section 5 5 and or RS 485 port see Section 5 6 and or Ethernet connector see Section 5 9 6 If required connect a remote contact closure switch see Section 5 10 7 Connect the power cord 8 Set the machine to the dual link mode see Section 5 3 Dual Link HD SDI Camera LL 7 mansnamn Dual Link Preview Dual Link _HD SDI Dual Link Computer Video Player HD SDI Mixer Controller Figure 4 Connecting the Dual Link VS 44HDxl 3G HD SD SDI 4x4 Matrix Switcher 5 3 Setting the Working Mode You
13. KRAMER ELECTRONICS LTD USER MANUAL MODEL VS 44HDx Il SG HD SD SDI 4x4 Matrix Switcher P N 2900 000476 Rev 4 mlb E VS 44HDxI Quick Start Guide This guide helps you install and use your product for the first time For more detailed m information go to http www kramerelectronics com support product_downloads asp E to download the latest manual or scan the QR code on the left Step 1 Check what s in the box F VS 44HDxl 3G HD SD SDI y 1 Quick Start sheet 4x4 Matrix Switcher Kramer RC IR3 Infrared Remote y 1 Power cord Control Transmitter with batteries 4 Rubber feet and user manual Step 2 Install the VS 44HDxl Mount the VS 44HDxl in a rack using the included rack ears or attach the rubber feet and place on a table Step 3 Connect the inputs and outputs Preview HD SDI Computer Display Mixer Controller Connect a genlock source and loop Connect the remote contact closure terminal block Step 4 Connect the power Connect the power cord to the VS 44HDxI and plug it into the mains electricity Step 5 Operate the VS 44HDxI TAKE Confirms actions Set DIP switches for the machine number ALL Selected input to all outputs OFF Press amp hold 3 secs to enter exit dual link mode Mach DiP4 pIP2 DIP3 2 OFF OFF OFF ON STO Stores status RCL Recalls status 3 OFF OFF ON OFF LOCK Locks front SETUP 4 oF OFF ON
14. Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and covers any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at http www kramerelectronics com support recycling Overview The VS 44HDxl is a high performance matrix switcher for 3G HD SDI and HD SDI dual link video signals The unit can be used as a high performance 4x4 matrix switcher or as a dual link 2x2 switcher that lets you simultaneously route any of the inputs to any or all of the outputs for all SDI video signals using BNC connectors Switching is implemented during the vertical interval period according to the SMPTE RP 168 standard when using synchronized digital video sources In particular the VS 44HDxtI features A maximum data rate of 3Gbps HDTV compatibility Multi standard operation SDI SMPTE 259M 344M HD SDI SMPTE 292M 3G HD SDI SMPTE 424M and dual link HD SDI SMPTE 372M Kramer Equalization amp re Klocking Technology that rebuilds the digital signal to travel longer distances S
15. SDI sources to the INPUT BNC connectors for example an HD SD SDI camera to input 1 and a 3G HD video server to input 4 2 Connect the OUTPUT BNC connectors to up to four SDI acceptors for example output 1 to a Preview display and output 4 to an HD SDI mixer 3 Set the DIP switches see Section 5 4 4 If required connect Agenlock source to the GENLOCK BNC connector Not illustrated in Figure 3 The LOOP BNC connector to the GENLOCK connector of the next unit in the line and release the TERM button for looping Pushed in terminates the input Release when the input extends to another unit 5 Connect a PC and or controller if required to the RS 232 port see Section 5 5 and or RS 485 port see Section 5 6 and or 0 S 44HDxl Connecting the VS 44HDxI Ethernet connector see Section 5 9 6 If required connect a remote contact closure switch refer to Section 5 10 7 Connect the power cord 8 If required exit the dual link mode see Section 5 3 HD SDI Camera Preview Display 3G HD SDI HD SDI Mixer Server Computer Figure 3 Connecting the VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher VS 44HDxI Connecting the VS 44HDxI Ee 5 2 Connecting the VS 44HDxI in the Dual Link Mode You can use your VS 44HDxI in the dual link mode to switch any of the two dual link SDI inputs to any or all of the two dual link SDI outputs as the illustration in Figure 4 shows To connect the VS 44
16. ailable from our Web site VS 44HDxI Installing in a Rack 4 1 Using the IR Transmitter You can use the RC IR3 IR transmitter to control the machine via the built in IR receiver on the front panel or instead via an optional external IR receiver Model C A35M IRR 50 The external IR receiver can be located up to 15 meters away from the machine This distance can be extended to up to 60 meters when used with three extension cables Model C A35M A35F 50 Before using the external IR receiver be sure to arrange for your Kramer dealer to insert the internal IR connection cable P N 505 70434010 S with the 3 5mm connector that fits into the REMOTE IR opening on the rear panel Connect the external IR receiver to the REMOTE IR 3 5mm connector Installing in a Rack 5 Connecting the VS 44HDxI Always switch off the power to each device before connecting it to your VS 44HDxI After connecting your VS 44HDxI connect its power and then switch on the power to each device This section describes how to connect the VS 44HDxl e To connect the VS 44HDxtI in the single link mode see Section 5 1 e To connect the VS 44HDxI in the dual link mode see Section 5 2 5 1 Connecting the VS 44HDxI in Single Link Mode You can use your VS 44HDxI to switch any of the four SDI inputs to any or all of the four SDI outputs as illustrated in Figure 3 To connect the VS 44HDxI as a 4x4 matrix switcher do the following 1 Connect up to four
17. can set the VS 44HDxI to work in the dual link mode as follows e To switch to the dual link mode press and hold the OFF front panel button for 3 seconds until a red dot illuminates on the display on the second segment of the 7 segment display and the OFF button flashes e To exit the dual link mode press and hold the OFF front panel button for 3 seconds until the red dot on the display disappears and the OFF button flashes VS 44HDxl Connecting the VS 44HDxI Eg 5 4 5 4 1 Setting the DIP Switches By default all the DIP switches are set to OFF Figure 5 illustrates the VS 44HDxl DIP switches SETUP ON Figure 5 VS 44HDxl SETUP DIP switches Setting the Machine DIP Switches The Machine determines the position of a VS 44HDxl unit specifying which VS 44HDxl unit is being controlled when several VS 44HDxI units connect to a PC or serial controller Set the Machine on a VS 44HDxI unit via SETUP DIPS 1 2 3 and 4 according to the following table When using a standalone VS 44HDxI unit set the Machine to 1 When connecting more than one VS 44HDxtI unit set the first machine the Master that is closest to the PC as Machine 1 DIP switches are set to OFF Mach DIP 1 DIP 2 DIP 3 DIP 4 cleat orr forr forr fon or forr fon fon _ orr ON orF_ oFF_ orr jon orF ON OFF jon ON OFF s forr on jon ON S 44HDxl Connecting the VS 44HDxl 5 5 VS 44HDxI Connecting the VS 4
18. ding INPUT OUTPUT key recalls a setup from the non volatile memory After pressing the same memory location the second time the settings take effect ALL Button Pressing ALL followed by an INPUT button connects that input to all outputs When in Confirm mode the TAKE button illuminates OFF Button An OFF OUT combination disconnects that output from the inputs an OFF ALL combination disconnects all the outputs Press and hold for more than 3 seconds to toggle between the 4x4 switcher mode and the dual link 2x2 switcher mode 10 LOCK Button Disengages the front panel buttons 7 segment display Displays the selected input switched to the output marked above each input Remote IR SA 7 2 4 3 2 3 2 4 4 ry CNA We We Me CN Wer We TU 0000 GENLOCK p LOOP a NPUTS TERM INPUTS OUTPUTS RS 232 IXQHtr M2IAJBAQ Figure 2 VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher Rear Panel Feature Function GENLOCK BNC Connector Connect to the genlock source TERM 75Q Button Press to terminate the genlock source 75Q or release for looping LOOP BNC Connector Connect to the GENLOCK connector of the next unit in the line 15 DUAL LINK INPUT BNC Connectors In the dual link mode connect the source to inputs 1 and 2 and or inputs 3 and 4 DUAL LINK 1 and or DUAL LINK 2 16 INPUT BNC Connectors Connect to the serial digital video sources from 1 to 4 17 DUAL LINK OUTPUT BNC Connectors In the dual link mode connect the accepto
19. e 6 bit INSTRUCTION defines the function performed by the switcher s If a function is performed using the machine s keyboard these bits are set with the INSTRUCTION NO performed The instruction codes are defined according to the table below INSTRUCTION NO is the value set in N5 NO 2nd Byte Bit 7 Defined as 1 16 10 INPUT When switching i e instruction codes 1 and 2 the 7 bit INPUT is set as the input number to be switched If switching is done using the machine s front panel these bits are set with the INPUT NUMBER switched For other operations these bits are defined according to the table 3rd Byte Bit 7 Defined as 1 O6 00 OUTPUT When switching i e instruction codes 1 and 2 the 7 bit OUTPUT is set as the output number to be switched If switching is done using the machine s front panel these bits are set with the OUTPUT NUMBER switched For other operations these bits are defined according to the table 4th Byte Bit 7 Defined as 1 Bit 5 Don t care OVR Machine number override M4 MO MACHINE NUMBER This byte is used to address machines in a system by their machine numbers When several machines are controlled from a single serial port they are usually configured together and each machine has an individual machine number If the OVR bit is set then all machine numbers accept implement the command and the addressed machine replies When a single machine is controlled over t
20. example for a 2216 the reply to the request to send the audio machine name is HEX code 7D 96 90 81 i e 1284ec 22dec for gm byte and 1284ec 16dec for 3 byte If the request for identification is sent with the INPUT set as 3 or 4 the appropriate machine sends its software version number Again the reply would be the decimal value of the INPUT and OUTPUT the INPUT representing the number in front of the decimal point and the OUTPUT representing the number after it For example for version 3 5 the reply to the request to send the version number would be HEX code 7D 83 85 81 i e 1284dec Sdec for gm byte 128dec 5dec for 30 byte If the OUTPUT is set as 1 then the ASCII coding of the lettering following the machine s name is sent For example for the VS 7588YC the reply to the request to send the first suffix would be HEX code 7D D9 c3 81 i e 1284ec ASCII for Y 1284ec ASCII for C Protocol 2000 Pan NOTE 14 The number of inputs and outputs refers to the specific machine being addressed not to the system For example if six 16x16 matrices are configured to make a 48x32 system 48 inputs 32 outputs the reply to the HEX code 3E 82 81 82 i e request the number of outputs would be HEX code 7E 82 90 82 i e 16 outputs NOTE 15 When the OVR bit ur byte is set then the video commands have universal meaning For example instruction 1 SWITCH VIDEO causes all units including a
21. has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your questions comments and feedback Web site www kramerelectronics com KRAMER E mail info kramerel com SAFETY WARNING Disconnect the unit from the power e supply before opening and servicing P N 2900 000476 Rev 4
22. he appropriate IP settings IP address Subnet mask Default gatewa Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server El Validate settings upon exit Figure 9 Internet Protocol Version 4 Properties Window cen You can get IPv6 settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IPv6 settings Obtain an IPv6 address automatically Use the following IPv6 address IPv6 address Subnet prefix length Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server l C Validate settings upon exit Figure 10 Internet Protocol Version 6 Properties Window VS 44HDxI Connecting the VS 44HDxI 19 5 9 2 5 9 3 6 Select Use the following IP Address for static IP addressing and fill in the details as shown in Figure 11 For TCP IPv4 you can use any IP address in the range 192 168 1 1 to 192 168 1 255 excluding 192 168 1 39 that is provided by your IT department General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically
23. he circuit s When connecting the machine to the supply circuit overloading the circuits might have a detrimental effect on overcurrent protection and supply wiring Refer to the appropriate nameplate ratings for information For example for fuse replacement see the value printed on the product label 5 The machine is earthed grounded in a reliable way and is connected only to an electricity socket with grounding Pay particular attention to situations where electricity is supplied indirectly when the power cord is not plugged directly into the socket in the wall for example when using an extension cable or a power strip and that you use only the power cord that is supplied with the machine To rack mount a machine 1 Attach both ear brackets to the machine To do so remove the screws from each side of the machine 3 on each side and replace those screws through the ear brackets 2 Place the ears of the machine against the rack rails and insert the proper screws not provided through each of the four holes in the rack ears Note In some models the front panel may feature built in rack ears Detachable rack ears can be removed for desktop use Always mount the machine in the rack before you attach any cables or connect the machine to the power e If you are using a Kramer rack adapter kit for a machine that is not 19 see the Rack Adapters user manual for installation instructions av
24. he serial port always set M4 MO to 1 and make sure that the machine itself is configured as MACHINE NUMBER 1 9 2 Instruction Codes All the values in the table are decimal unless otherwise stated Instruction Codes for Protocol 2000 Instruction Definition for Specific Instruction Description Output RESET VIDEO JO O_ RESETVIDEO 1 SWITCH VIDEO Set equal to video input Set equal to video output that is hat is switched switched 0 disconnect 0 to all the outputs E REQUEST STATUS OF A VIDEO OUTPUT 10 REQUEST VIS Set as SETUP or 0 VIS source SETTING set to 126 or 127 to 1 Input or output of source request if machine has 2 Vertical sync freq Hz this function 15 REQUEST WHETHER 0 For checking if setup is SETUP IS DEFINED defined VALID INPUT IS 1 For checking if input is valid DETECTED 2 For checking if output is valid Output 3 For checking if EDID output is valid 16 ERROR BUSY For invalid valid input i e 0 Error OUTPUT byte 4 or 1 Invalid instruction OUTPUT byte 5 2 Out of range this byte is set as the input 3 Machine busy 4 Invalid input 5 Valid input For invalid valid output 6 RX buffer overflow i e OUTPUT byte 7 or 7 Invalid output OUTPUT byte 8 this 8 Valid output byte is set as the output 9 Valid EDID 0 30 LOCK FRONT PANEL 0 Unlock panel 1 Lock panel PANEL IS LOCKED IDENTIFY M
25. l VS 44HDxI Overview M JAAO IXAHtY SA 3G HD SD SDI 4x4 Matrix Switcher VS 44HDx Figure 1 VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher Front Panel Feature Function a IR Receiver The LED illuminates when receiving signals from the infrared remote control transmitter 2 POWER Switch Illuminated switch for turning the unit ON or OFF 3 INPUT SELECTOR Select the input to switch to the output from 1 to 4 DUAL LINK Buttons In the dual link mode select input 1 or 2 to switch dual link 1 or 2 to the outputs Press IN buttons 1 2 and 3 simultaneously to reset the machine to its factory default values see Section 5 6 The 7 segment display shows 1234 indicating that the operation mode is normal and that the setups stored via the INPUT OUTPUT buttons have been erased Use to set the resolution when switching genlocked video signals see Section 5 8 OUTPUT SELECTOR DUAL Select the output to which the input is switched from 1 to 4 LINK Buttons In the dual link mode select output DUAL LINK 1 or DUAL LINK 2 to which the input is switched 5 STO STORE Button Pressing STO followed by an INPUT OUTPUT button stores the current setting TAKE Button Pressing TAKE toggles the mode between the CONFIRM mode and the AT ONCE mode user confirmation per action is unnecessary When in CONFIRM mode the TAKE button implements a pending operation See Section 6 2 7 RCL RECALL Button Pressing the RCL button and the correspon
26. ng cannot be programmed otherwise the reply to the HEX code 0A FE 80 81 i e request VIS setting with INPUT set as 1264ec is HEX code 4A FE 81 81 i e VIS setting 1 defined as VIS from input 1 NOTE 7 Setting OUTPUT to 0 returns the VIS source setting as defined in instruction 7 Setting to 1 returns the input or output of the sync source in the case where the VIS source is set as 6 or as 7 in instruction 7 Setting to 2 returns the vertical sync frequency 0 for no input sync 50 for PAL 60 for NTSC 127 for error NOTE 8 The reply is as in NOTE 4 above except that the OUTPUT is assigned with the value 0 if the setup is not defined no valid input is detected or 1 if it is defined valid input is detected NOTE 9 An error code is returned to the PC if an invalid instruction code was sent to the switcher or if a parameter associated with the instruction is out of range e g trying to save to a setup greater than the highest one or trying to switch an input or output greater than the highest one defined This code is also returned to the PC if an RS 232 instruction is sent while the machine is being programmed from the front panel Reception of this code by the switcher is not valid NOTE 13 This is a request to identify the switcher s in the system If the OUTPUT is set as 0 and the INPUT is set as 1 2 5 or 7 the machine sends its name The reply is the decimal value of the INPUT and OUTPUT For
27. o LOCKS tront pane 5 OFF ON OFF OFF TAKE ALL OFF 6 orF ON orF jon E O Ei 7 OFF ON ON OFF STO RCL LOCK 8 orF ON ON ON Contents 1 Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Recycling Kramer Products 3 Overview 3 1 Defining the VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher 4 Installing in a Rack 4 1 Using the IR Transmitter 5 Connecting the VS 44HDxl 5 1 Connecting the VS 44HDXxI in Single Link Mode 5 2 Connecting the VS 44HDxl in the Dual Link Mode 5 3 Setting the Working Mode 5 4 Setting the DIP Switches 5 5 Connecting the RS 232 Port 5 6 Connecting a PC or Controller to the RS 485 Port 5 7 Performing a Factory Reset 5 8 Switching Genlocked Video Signals 5 9 Operating via Ethernet 5 10 Controlling via the REMOTE Connector 6 Operating the VS 44HDxI 6 1 Switching Combinations 6 2 Confirming Settings 6 3 Storing Recalling Input Output Configurations 6 4 Locking the Front Panel 7 Technical Specifications 8 Table of Hex Codes for Serial Communication 9 Protocol 2000 9 1 Syntax 9 2 Instruction Codes Figures Figure 1 VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher Front Panel Figure 2 VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher Rear Panel Figure 3 Connecting the VS 44HDxl 3G HD SD SDI 4x4 Matrix Switcher Figure 4 Connecting the Dual Link VS 44HDxl 3G HD SD SDI 4x4 Matrix Switcher Figure 5 VS 44HDxI SETUP DIP switches Figure
28. o the device and click Change settings of this connection The Local Area Connection Properties window for the selected network adapter appears as shown in Figure 8 Sharing Connect using Intel R 82579V Gigabit Network Connection This connection uses the following items o Client for Microsoft Networks E Microsoft Network Monitor 3 Driver Z QoS Packet Scheduler d2 File and Printer Sharing for Microsoft Networks E Intemet Protocol 6 4 Intemet Protocol Version 4 TCP IPv4 Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder Install Uninstall Properties Descripti TCP IP version 6 The latest version of the intemet protocol that provides communication across diverse interconnected networks K K K K K K K K Figure 8 Local Area Connection Properties Window 4 Highlight either Internet Protocol Version 6 TCP IPv6 or Internet Protocol Version 4 TCP IPv4 depending on the requirements of your IT system 5 Click Properties The Internet Protocol Properties window relevant to your IT system appears as shown in Figure 9 or Figure 10 VS 44HDxI Connecting the VS 44HDxI General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for t
29. oes not flash if the new timing is the same as that previously selected e 1080i 50Hz or 720p 50Hz press and hold INPUT 2 button for 3 seconds The button flashes to indicate that the set up was completed VS 44HDxI Connecting the VS 44HDxI 5 9 5 9 1 e 720p 60tz press and hold INPUT 3 button for 3 seconds The button flashes to indicate that the set up was completed When turning the machine ON the appropriate button flashes to indicate the latest setup last setup is saved Operating via Ethernet You can connect to the product via Ethernet using either of the following methods e Directly to the PC using a crossover cable see Section 5 9 1 e Via a network hub switch or router using a straight through cable see Section 5 9 2 Note If you want to connect via a router and your IT system is based on IPv6 speak to your IT department for specific installation instructions Connecting the Ethernet Port Directly to a PC You can connect the Ethernet port of the VS 44HDxtI directly to the Ethernet port on your PC using a crossover cable with RJ 45 connectors This type of connection is recommended for identifying the VS 44HDxI with the factory configured default IP address After connecting the VS 44HDxI to the Ethernet port configure your PC as follows 1 Click Start gt Control Panel gt Network and Sharing Center 2 Click Change Adapter Settings 3 Highlight the network adapter you want to use to connect t
30. perating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Krame
31. r Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability
32. reference After pressing the same memory location the second time the settings take effect To cancel this action press the RCL button once again VS 44HDxl Operating the VS 44HDxI 2 6 4 Locking the Front Panel To prevent changing the settings accidentally or tampering with the unit via the front panel buttons lock your VS 44HDxI Unlocking releases the protection mechanism Even though the front panel is locked you can still operate via RS 232 or RS 485 as well as via the Kramer IR remote control transmitter To lock the VS 44HDx e Press the LOCK button for three seconds until the LOCK button is illuminated The front panel is locked Pressing a button has no effect To unlock the VS 44HDxI e Press the illuminated LOCK button until the LOCK button is no longer illuminated The front panel unlocks VS 44HDxI Operating the VS 44HDxI 7 ve S 44HDxI Technical Specifications Technical Specifications INPUTS 4 SMPTE 259M 292M 424M 372M for dual link HD SDI signals serial video 75 ohms on BNC connectors 1 GENLOCK 75Q Hi Z on a BNC connector hi level or tri level sync OUTPUTS 4 equalized and reclocked SMPTE 259M 292M 372M for dual link HD SDI signals outputs 75 ohms on BNC connectors 1 Looped GENLOCK 759 Hi Z on a BNC connector MAX OUTPUT LEVEL 800mVpp 75 ohms DATA RATE Up to 2 97Gbps CONTROLS Front panel RS 232 RS 485 Ethernet infra red remote contact clo
33. rs to outputs 1 and 2 and or outputs 3 and 4 DUAL LINK 1 and or DUAL LINK 2 18__ OUTPUT BNC Connectors Connect to the serial digital video acceptors from 1 t04 O Section 5 10 SETUP DIP switches DIP switches for setup of the unit 23 REMOTE IR Opening Connects to an external IR receiver unit for controlling the machine via an IR remote controller instead of using the front panel IR receiver Covered by a cap The 3 5mm connector at the end of the internal IR connection cable fits through this opening Ethernet Connector Connects to the PC or other Serial Controller through computer networking Power Connector with Fuse AC connector enabling power supply to the unit 4 Installing in a Rack This section provides instructions for rack mounting the unit Before installing in a rack be sure that the environment is within the recommended range O to 40 C 32 to 104 F 40 to 70 C 40 to 158 F 10 to 90 RHL non condensing OPERATING TEMPERATURE STORAGE TEMPERATURE HUMIDITY T CAUTION When installing on a 19 rack avoid hazards by taking care that 1 Itis located within the recommended environmental conditions as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature 2 Once rack mounted enough air will still flow around the machine 3 The machine is placed straight in the correct horizontal position 4 You do not overload t
34. sure and panel lock POWER CONSUMPTION OPERATING TEMPERATURE 0 to 40 C 32 to 104 F STORAGE TEMPERATURE DIMENSIONS 19 x 7 x 1U W D H rack mountable WEIGHT ACCESSORIES OPTIONS C A35M IRR 50 external remote IR receiver cable Specifications are subject to change without notice at http Awww kramerelectronics com Table of Hex Codes for Serial Communication The following table lists the hex values for a single machine MACHINE 1 IN OUT 1 IN OUT2 IN OUT3 IN OUT 4 VS 44HDxI Table of Hex Codes for Serial Communication 9 1 ve 4HDxI Protocol 2000 Protocol 2000 This RS 232 RS 485 communication protocol uses four bytes of information as defined below For RS 232 a null modem connection between the machine and controller is used The default data rate is 9600 baud with no parity 8 data bits and 1 stop bit Note Compatibility with Kramer s Protocol 2000 does not mean that a machine uses all of the commands below Each machine uses a sub set of Protocol 2000 according to its needs Syntax MSB LSB 1st Byte DESTINATION INSTRUCTION o DNS NAN NNT NO 3rd Byte OUTPUT fp os SH tc ft CO 7 eS e h do 4th Byte MACHINE NUMBER ooo Jon p m m eM Zo de ds e B e e o 1st Byte Bit 7 Defined as 0 D DESTINATION 0 Sends information to the switchers from the PC 1 Sends information to the PC from the switcher N5 NO INSTRUCTION Th
35. to REMOTE PIN G Ground INPUTS OUTPUTS G1234 1234 Stage 2 Temporarily connect INPUT PIN 1 to REMOTE PIN G Ground INPUTS OUTPUTS G1234 1234 o o lolol e eie elle Figure 12 Using the REMOTE Connector In the dual link mode only inputs and outputs 1 and 2 are used as are the INPUT and OUTPUT selector buttons Remote pins 3 and 4 and selector buttons 3 and 4 are not used VS 44HDxI Connecting the VS 44HDxI 6 6 1 Operating the VS 44HDxl You can operate your VS 44HDxI via The front panel buttons RS 232 RS 485 serial commands transmitted by a PC touch screen system or other serial controller The Kramer infrared remote control transmitter The infrared remote extension cable transmitter The Ethernet Switching Combinations Section 6 1 1 describes how to switch OUT IN combinations and Section 6 1 2 how to switch OUT IN combinations in the dual link mode Note that The OUTPUT button color changes during routing according to the input button color green for standard definition or blue for high definition If an OUTPUT button is not selected that button does not illuminate If a source is connected to an INPUT that INPUT button illuminates Switching OUT IN Combinations To switch an input to an output via the front panel buttons in the
36. to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product
37. udio data etc to switch Similarly if a machine is in FOLLOW mode it performs any video instruction NOTE 16 The reply to the REQUEST WHETHER PANEL IS LOCKED is the same as in NOTE 4 above except that OUTPUT is assigned with the value 0 if the panel is unlocked or 1 if it is locked NOTE 25 For units that detect the validity of the video inputs instruction 16 is sent whenever the unit detects a change in the state of an input in real time For example if input 3 is detected as invalid the unit sends HEX code 10 83 84 81 If input 7 is detected as valid then the unit sends HEX code 10 87 85 81 VS 44HDxl Protocol 2000 LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product
38. witching synchronization that synchronizes either to external reference or incoming video Active Input Type reporting where each input button on the front panel automatically lights up when the unit detects a video signal on that input Green indicates a standard definition SDI input signal and blue indicates a high definition HD SDI input signal Multiple Memory Locations that store multiple switches as presets salvos to be recalled and executed when needed A take button that executes multiple switches all at once Bi level tri level analog sync Selectable sync signal termination Looping sync input Front panel control lockout Flexible control options front panel RS 232 K Router Windows based software is included RS 485 Ethernet contact closure amp IR Remote included Worldwide power supply of 100 240V AC Standard 19 rack mount size 1U with rack ears included The VS 44HDxl which is housed in a 19 1U rack mountable enclosure and is fed from a 100 240V AC universal switching power supply can be controlled via the front panel buttons or via the Infrared remote control transmitter Infrared remote extension cable transmitter Remotely by RS 232 or RS 485 serial commands transmitted by a touch screen system PC or other serial controller Ethernet Remote contact closure for forced operation 3 1 Defining the VS 44HDxI 3G HD SD SDI 4x4 Matrix Switcher This section defines the VS 44HDx
Download Pdf Manuals
Related Search