Manual for FSD
Contents
1. 240V AC O ff 50 60Hz Figure 2 2 FSD 804P Switch rear panel Power Notice 1 The device is a power required device it means it will not work till it is powered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime 2 In some area installing a surge suppression device may also help to protect your FSD 804P from being damaged by unregulated surge or current to the FSD 804P or the power adapter 2 4 Hardware Installation 2 4 1 Before start up Before your installation please refer to the followings for your cabling 100Base TX All 100Base TX ports come with Auto Negotiation capability They automatically support 100Base TX and 10Base T networks Users only need to plug a working network device into one of the 100Base TX ports and then turn on the FSD 804P The port will automatically runs in 10Mbps 20Mbps 100Mbps or 200Mbps after the negotiation with the connected device Cabling Each 10 100Base TX ports use RJ 45 sockets similar to phone jacks for connection of unshielded twisted pair cable UTP The IEEE 802 3u Fast Ethernet standard requires Category 5 UTP for 100Mbps 100Base TX 10Base T networks can use Cat 3 4 or 5 UTP see table below Maximum distance is 100meters 328 feet Port Typ2. This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of Ss WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET 8 Port 10 100Mbps with 4 Port PoE Ethernet Switch User s Manual FOR MODEL FSD 804P REVISION 2 0 SEPTEMBER 2007 Part No 2080 A31 120 003 TABLE OF CONTENTS 1 INTRODUCTION 00 anida 4 LL NCHECKO Ti A A IN LA 4
3. 12 HOW TO USE THIS MANUAL id ii A A E bra 4 T3 FEATURES u e h Auk A A dE A A A Ad 4 IA SPECIFICATION ii Audie Acie A A pda ibi da 5 2 HARDWARE DESCRIPTION amp nccccicccicscccdecccsctesiesescoeetestcdecesedcceccedeadesescdennecods sdunecedadcudeaedcenebesaceuseandclesaadaauaued 6 2 APRODUGT DESGRIBTION SS A as 6 PRPA RONTIRANE Learn ias Rada IA a it dd A Elias 6 ZO MREAR RANES Eat lt a adn la setae oe 7 2 4 HARDWARE INSTALCATION a A A dais 7 2 5IDESKTOP INSTALLATION Si A ohtceups sche ace ceats AA 8 2 0 RACK MOUNTING 344 ciar nd ci IA ses lata cent apetenath ten a E 9 2 RRAODUETIAPPLICATION a da cda putaeatesees 10 3 S WITCH OPERA TION cuco o sed vacetecvusateacesemeodeadsassacesuacdsatececeaciveads Dias scada 12 SWADDRESS TABLE et ceccthici tebe stl iher g Makita eles ALR iea ant OR e hil NG a lab dl oll ea eine a Mal ita 12 SEO GEARNING 57 00 EA atreva ei noodle lor Mace hater KEENAN AEAN cali teal e batida bate td al ob caco dol 12 3 3 FORWARDING amp FILTERING 00 te tector dto tl les ENTE led ette ade e etl ha bree olen he 12 34 STORE AND FORWARD EEEN A ETENN ENEY loli ENTE rra lo haere bso ideo ico ells 12 3 5 AUTO NEGOTIATION 3 ccecitcasiiat ie derretida tee doyle iris leal Aare ad 12 4 TROUBLESHOOTIN Guia atadas 13 APPENDIX A NETWORKING CONNECTION ccooocccccccconconconoococconnnnonononoconnnnnnnananononanananananrn rr nnanananananannrananaaas 14 A 1 SwIiTCH S RJ 45 PIN ASSIGNMENTS ccccccconcnoccncnnnonononenanonononononnnnnan
4. The STP ports on the FSD 804P switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another network device usually at Power On or Reset Detecting the modes does this and speeds at the second of both devices are connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full duplex mode 12 4 TROUBLESHOOTING This chapter contains information to help you solve problems If the Switch is not functioning properly make sure the Ethernet Switch was set up according to instructions in this manual The Link LED is not lit Solution Check the cable connection and remove duplex mode of the Switch Performance is bad Solution Check the full duplex status of the Switch If the Ethernet Switch is set to full duplex and the partner is set to half duplex then the performance will be poor 100Base TX port link LED is lit but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why the Switch doesn t connect to the network Solution Check the LNK ACT LED on the switch Try another port on the Switch Make sure the cable is installed properly Make sure the cable is the right type Turn off the power After a while turn on powe
5. and Forward is one type of packet forwarding techniques A Store and Forward Ethernet Switching stores the incoming frame in an internal buffer do the complete error checking before transmission Therefore no error packets occurrence it is the best choice when a network needs efficiency and stability The Ethernet Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if required The fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Ethernet switching the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines network traffic to its re spective domain reducing the overall load on the network The Switch performs Store and forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 3 5 Auto Negotiation
6. power source outlet When the Switch receives power the Power LED should remain solid Green 3 Connect other switch or PC to one port of the FSD 804P using Category 3 4 5 UTP STP cabling 4 Connect another switch or PC to the other port of FSD 804P by following the same process as described in Step 3 UILINN FSD 804P y THH n FGSW 2402VS Figure 2 6 End node or Switch connection A Notice Cable distance for Switch The cable distance between the FSD 804P and PC should not exceed 100 meter for UTP STP cable Make sure the wiring is correct It can be used Category 3 4 5 cable in 10 Mbps operation To reliably operate your network at 100Mbps you must use an Unshielded Twisted Pair UTP Category 5 cable or better Data Grade cabling While a Category 3 or 4 cables may initially seem to work it will soon cause data loss 10 2 7 2 Department Workgroup PoE Switch Providing up to 4 PoE in line power interfaces the Switch can easily build a power central controlled IP phone system IP camera system AP group for the enterprise For instance 4 camera AP can be easily install around the cornerin the company for surveillance demands or build a wireless roaming environment in the offices Without the power socket limitation the switch makes the installation of cameras or WLAN AP more easily and efficiently 10 100Base TX Data Power mm 10 100Base TX Data Figure 2 7 Department workgroup PoE Switch connecti
7. FSD 804P 8 Port 10 100Mbps with 4 Port PoE Fast Ethernet Switch is ny Pa w M PLANET Networking amp Communication Trademarks Copyright PLANET Technology Corp 2007 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning
8. ceives power the Power LED should remain solid Green 2 6 Rack Mounting To install the Switch in a 10 inch standard rack follow the instructions described below Step1 Place your Fast Ethernet Switch on a hard flat surface with the front panel positioned towards your front side Step2 Attach a rack mount bracket to each side of the Switch with supplied screws attached to the package Figure 2 4 shows how to attach brackets to one side of the Switch Figure 2 4 Attaching the brackets to the Switch Caution You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect screws would invalidate your warranty Step3 Secure the brackets tightly Step4 Follow the same steps to attach the second bracket to the opposite side Step5 After the brackets are attached to the Switch use suitable screws to securely attach the brackets to the rack as shown in Figure 2 5 080000 ac 0088000 Figure 2 5 Mounting the Switch in a Rack Step6 Proceeds with the steps 4 and steps 5 of session 2 5 Desktop Installation to connect the network cabling and supply power to your Switch 2 7 Product Application 2 7 1 Connecting end node or switch 1 Place the FSD 804P on a smooth surface or fasten the mounting brackets purchased separately with the provided screws in a standard 19 rack 2 Connect the power cord to the power inlet socket of FSD 804P and the other end into the local
9. cncnnonnnnarnnnnnn conocen ana nnnnn nn nn aan n ana narnia 14 A 2 RJ 45 CABLE PIN ASSIGNMENT oooocccccccnconnnonoccnnnnnnnononenanancnononnnannnnnnnnn nono a anna rca nn nn nena ana nan nano EEEE nan anna caninas 14 1 INTRODUCTION 1 1 Checklist Check the contents of your package for following parts e FSD 804P x1 e User s manual CD x1 e Power cord x 1 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 How to Use This Manual The PoE Ethernet Switch User manual is structured as follows Chapter 2 Installation This chapter explains the functions and how to physically install the FSD 804P Chapter 3 Switch Operation This chapter explains the switch operation of FSD 804P Chapter 4 Trouble Shooting This chapter contains troubleshooting of FSD 804P Appendix This chapter contains cable information of FSD 804P In the following section the term Switch means the Switch device ie FSD 804P term of switch can be any third switches 1 3 Features 8 Port 10 100Mbps Fast Ethernet ports 4 Port supports 48VDC power to PoE Powered device Hardware based 10 100Mbps auto negotiation Flow control for full duplex operation and back pressure for half duplex operation Integrates address look up engine supports 2K absolute MAC addr
10. e Cable Type Estats 10Base T Cat 3 4 5 2 pair RJ 45 100Base TX Cat 5 UTP 2 pair RJ 45 Any Ethernet devices like hubs PCs can connect to the FSD 804P by using straight through wires The eight 10 100Mbps ports are auto MDI MDI X can be used on straight through or crossover cable 2 5 Desktop Installation To install the Switch on desktop simply follow the next steps Step1 Attach the rubber feet to the recessed areas on the bottom of the Switch as shown in Figure 2 3 Figure 2 3 Attaching the rubber feet to the Fast Ethernet Switch Step2 Place the Switch on desktop near an AC power source Step3 Keep enough ventilation space between the Switch and the surrounding objects Notice When choosing a location please keep in mind the environmental restrictions discussed in Chapter 1 Section 1 4 Product Specification Step4 Connect your Switch to network devices A Connect one end of a standard network cable to the 10 100 RJ 45 ports on the Back of the Switch B Connect the other end of the cable to the network devices such as printer servers workstations or routers etc Notice Connection to the Fast Ethernet Switch requires UTP Category 5 network cabling with RJ 45 tips For more information please see the Cabling Specification in Appendix A Step5 Supply power to the Switch A Connect one end of the power cable to the Switch B Connect the power plug of the power cable to a standard wall outlet When the Switch re
11. esses Automatic address learning and address aging Supports Auto MDI MDI X function LED indicators for easy network diagnostic Ethernet standards comply with IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3x Flow Control and IEEE 802 3af Power over Ethernet e EMI standards comply with FCC CE class A 9 48 o 2 1 4 Specification FSD 804P 8 Port RJ 45 for 10 100TX 4 Port with PoE injector function Port 1 to Port 4 One power 1 4 port PoE in use LNK ACT 100 5 8 port LNK ACT 100 End point insert type and compatible with IEEE 802 3af Per port feeding power 48V DC 15 4W 350mA Maximum Ping 1 2 3 6 0 40 degree C 10 95 RH 40 70 degree C 95 RH 5 to 90 relative humidity non condensing 5 to 90 relative humidity non condensing IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3x Flow Control IEEE 802 3af Power over Ethernet 2 HARDWARE DESCRIPTION This product provides two different running speeds 10Mbps 100Mbps in the same switch and automatically distinguishes the speed of incoming connection This section describes the hardware features of FSD 804P For easier management and control of the Switch familiarize yourself with its display indicators and ports Front panel illustrations in this chapter display the unit LED indicators Before connecting any network device to the FSD 804P please read this chapter carefully 2 1 Product Descripti
12. he installation costs simplifying the installation effort and eliminating the need for electricians or extension cords We are also proud of the key feature energy saving With more efficient switching power supply the efficiency of the FSD 804P would be much better than four linear power adapters in a long run 2 2 Front Panel The Front Panel of the FSD 804P PoE Ethernet Switch consists of 8x Auto Sensing 10 100Mbps Ethernet RJ 45 Ports The LED Indicators are also located on the front panel of the FSD 804P PLANET 8 Port 10 100Mbps Web Smart Switch Networking Communication FSD 804PS with 4 Port PoE Injector OOO O PoEIn Use 0000 O O O O LNK ACT SSCS 00901 beer yee hehe ape ae PWR1 2 3 4 5 6 7 8 Figure 2 1 FSD 804P Switch front panel 2 2 1 LED indicators System ED Color Function EAEN Lights to indicate that the Switch has power m Per 10 1 TEZ i Color Function ENA Lights to indicate the port is providing 48VDC in line power 1 4 ports Lit indicate the link through that port is successfully established Blinks to indicate that the Switch is actively sending or receiving data over that port 100 Green Lights to indicate the port is running in 100Mbps speed 2 3 Rear Panel The rear panel of the FSD 804P indicates an AC inlet power socket which accepts input power from 100 to 240VAC 50 60Hz 1A max 100
13. n 8 Brown SIDE 2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown
14. on The FSD 804P is equipped with unshielded twisted pair UTP cable ports providing dedicated 10 or 100Mbps bandwidth The FSD 804P supports MDI MDI X convertible on 8 10 100Mbps ports also provide PoE inject function on port 1 2 3 4 which is able to drive 4 IEEE 802 3af compliant powered devices The dual speed ports use standard twisted pair cabling and are ideal for SOHO or segmenting networks into small Each 10 100Mbps port can supports up to 200Mbps of throughput in full duplex mode the FSD 804P also provides a simple cost effective and highly reliable network connec tion for data as well as power Furthermore it is the ideal device for bridging among Ethernet Fast Ethernet workgroups and networks With 4 PoE interfaces the FSD 804P is ideal for small business and workgroups requiring to deploy the PoE for the wireless access points IP based surveillance camera or IP phones in any places easily efficiently and cost effective The front panel of FSD 804P provides LEDs for easy recognition of the switch operation status and troubleshooting These LED indicators display the power status for the system LNK ACT and speed for each10 100M port Also the PoE in use LED indicates for PoE ports port 1 to port 4 With data and power over Ethernet from one unit the FSD 804P shall reduce cables and eliminates the need for dedicated electrical outlets on the wall ceiling or any unreachable place A wire carries both data and power lowering t
15. on a 3 SWITCH OPERATION 3 1 Address Table The Switch is implemented with an address table This address table composed of many entries Each entry is used to store the address information of some node in network including MAC address port no etc This information comes from the learning process of Ethernet Switch 3 2 Learning When one packet comes in from any port The Switch will record the source address port no And the other related information in address table This information will be used to decide either forwarding or filtering for future packets 3 3 Forwarding amp Filtering When one packet comes from some port of the Ethernet Switching it will also check the destination address besides the source address learning The Ethernet Switching will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Ethernet Switching will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filtered Thereby increasing the network throughput and availability 3 4 Store and Forward Store
16. r again Why connect my PoE device to FSD 804P and it cannot power on Solution 1 Please check the cable type of the connection from FSD 804 port 1 to port 4 to the other end The cable should be an 8 wire UTP Category 5 or above ElA568 cable within 100 meters A cable with only 4 wire short loop or over 100 meters all will affect the power supply 2 Please check and assure the device that fully complied with IEEE 802 3af standard 13 APPENDIX A NETWORKING CONNECTION A 1 Switch s RJ 45 Pin Assignments Contact MDI 1 TX 2 1X 3 RX 6 RX A 2 RJ 45 cable pin assignment qa le G A 32 There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation 1 2 and color of straight cable and crossover cable connection Cr verc 1234567 8 SIDE 1 LS 1234567 8 SIDE 2 Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 2080 A31120 003 SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Biue 6 Green 7 White Brown 8 Brown SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 6 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brow
Download Pdf Manuals
Related Search