User`s Manual
Contents
1. OUT DMX IN DMX OUT DMX IN DMX OUT DMX IN FROM CONTROLLER TERMINATOR 5 20 Pilot 1200 EN doc DMX TERMINATOR In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with a 120Q ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connections are illustrated below 2 jd WU va PIN 3 SETUP WONFIGURATION Connect a 120 resistor across pins 2 and 3 in an XLR plug and insert into the DMX OUT socket on the last unit in the chain FUNC DOWN UP ENTER Projector configuration can be set conveniently pressbutton switch and digital display the projector on and the digital display will show DMX address you set and save last time and it can be reset and saved again as you please Press button UP or DOWN if you want to browse through the various Setup Options Press button ENTER to save your settings or enter the next menu Press button or DOWN to shift PIN 2 the display between change display of address Press button FUNC it will return to the upper menu by one2. RELIABILITY PILOT 1200 PR 2900 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PR LIGHTING LTD No 571 Yingbin Road Dashi Panyu Guangzhou 511430 China http www pr lighting com INDEX SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR 4 FITTING THE LAMP 4 POWER SUPPLY MAINS 5 CONTROL CONNECTIONS 5 DMX TERMINATOR 6 SETUP OPTIONS PROJECTOR CONFIGURATION 6 TO SET THE DMX START ADDRESS 6 FUNCTIONS DISPLAY 7 ERRORS DISPLAY 9 REPLACING GOBOS 9 DMX CONTROL CHANNEL FUNCTIONS 10 LED DISPLAY 13 CHANGING BELTS 13 MAINTENANCE 14 LUBRICATION 14 KEEPING THE PROJECTOR CLEAN 14 TROUBLESHOOTING 14 TECHNICAL DATA 16 ELECTRICAL DIAGRAM 18 COMPONENT ORDER CODES 19 Please note that as part of our ongoing commitment to continuous product development specifications are subject to change without notice Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement The publishers cannot be held responsible for the accuracy of the information herein or any consequence arising from them Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and or the unit are in good condition before installation and use Should there be any damage c
3. The display will return automatically to the function of address display if you stay for about 60 seconds defaulted E g if you want to set the function of Pan Tilt 16bit precision valid do as follows launch the apparatus press button to Addr which is displayed in digital display press button to UPEn press button ENTER it will display nuP press button UPI consecutively to Hr E5 press button ENTER it will display press button ON to in the end press button ENTER Well done you have validated this function now If you want to set the function of Pan Tilt 16bit precision invalid press button DOWN to Then press button ENTER to invalidate this function And if you want to set another function valid or not press button to track back one by one then do the same way of e g above TO SET THE DMX START ADDRESS Each PILOT 1200 must be given a DMX start address so that the correct projector responds to the correct control signals This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller The PILOT 1200 has 22 channels so set the No 1 projector s address 001 2 projector s address 023 3 projector s address 045 No 4 projector s address 067 and so on Launch the projector Press button FUNC to Addr press button ENTER it will displa
4. please state the exact name and part no Repairs must be carried out by a qualified technician 19 20 Pilot 1200 EN doc LIGHTING LTD No 571 Yingbin Road Dashi Panyu Guangzhou China Post Code 511430 TEL 86 20 8478 1888 FAX 86 20 8478 6023 P N 321010221 Last Revision 07 05 2006 20 20 Pilot 1200
5. doc LIGHT OUTPUT 25 lux 3800 950 422 237 18 lux 8600 2150 955 537 4m 2m 2 4m DISTANCE Om 5m 10m 15m 20m 18 DIAMETER 1 5 3 1m 4 7m 6 3m 25 ss 2 2m 4 4m 6 6 8 8 15 20 Pilot 1200 EN doc TECHNICAL DATA VOLTAGES 200 220 230 240V AC 50Hz or 60Hz POWER CONSUMPTION 1628W 220V LAMP Type MSR 1200W SA DE discharge lamp Colour Temperature 6000 K Socket SFc10 4 Manufacturers Rated Lamp Life 750 Hours COLOURS CYM colour mixing system 1 wheel with 7 fixed dichroic colours plus white With variable speed bidirectional rainbow effect COLOUR TEMPERATURE CORRECTION 2 colour temperature correction filters GOBOS Rotating gobo wheel 4 interchangeable gobos white indexable bidirectionally rotating at variable speeds Fixed gobo wheel 4 interchangeable gobos white the fixed gobo wheel can scroll in eather direction at variable speeds Both glass gobos and metal gobos may be fitted to either wheel Gobo diameter 51 8mm Gobo image diameter 048mm PRISM 1x2 facet 1 x 3 facet 1x5 facet 1 x linear prisms indexable bidirectionally rotating at variable speeds FOCUS DMX controlled focus EFFECT FILTERS 1 ultraviolet filter and 1 bicolour filter FROST Variable frost effect 0 100 linearly adjustable SHUTTER Double shutter blades 0 100 linearly adjustable STROBE 1 7 F P S HEA
6. 12 Colour wheel reset error Er17 Prism rotation reset error Er18 Prism change reset error Er20 Fixed gobos reset error Er25 Pan motor reset error Er26 Tilt motor reset error REPLACING GOBOS EFFECT WHEEL sie 9 N NC GOBOS RETAINING SPRING Lock Tilt Loosen 2 screws on the rear cover with fans and open the rear cover with fans You could see the structure as shown in the above figure For gobos replacement on the fixed gobo wheel turn the effect wheel and rotated gobo wheel to a proper position first take out a gobo from the fixed gobo wheel carefully fit a new gobo Note if the gobo is a glass one it should be touched with lint free clean and soft tissue or cloth matted between hand and glass instead of with bare hand For filters replacement on the effect wheel do in the same way of fixed gobo wheel For gobos replacement on the rotated gobo wheel take an appropriate tool to tug the head of retaining spring up and engage your another hand to take the retaining spring out take the gobo out fit a new gobo and fit the retaining spring Notes the gobo cannot be touched with bare hand never attempt to dismantle the gobo holder on which you want to replace the gobo be careful of the gobo when the replacement is underway and don t drop it Close the rear cover and fasten 2 M5 screws 9 20 Pilot 1200 EN doc CONTROL CHANNEL FUNCTIONS The PILOT 1200 uses 22 DMX channe
7. 220 230V THERMOSTAT 190010035 1 KSD020 120 15A 250V RELAY 192010026 1 H380D100 CAPACITOR 140010043 2 7 7 BALLAST 040070059 2 230V 50 60Hz 575W IGNITOR 040090036 1 575 1200W 6 8KV LAMP 100050054 1 1200W SA DE PAN amp TILT DRIVE BELT 290151221 2 HTD459 3M 6 PAN amp TILT DRIVE BELT 290151221 2 HTD459 3M 6 KDE2408PTB1 6 FAN IN STROBE SUNNO 030060031 2 2AVDC 3 4W FAN IN STROBE SUNNO 030060049 1 KD2406PTS1 DC24V 2 6W FAN ON THE REAR COVER 030060039 2 NMB BG0903 B054 000 TO FAN IN BASE SUNNO 030060048 2 KD2409PTB1 6 24VDC PAN MOTOR 030040089 2 239520391 6 35 25 TILT MOTOR 030040068 2 23HS0001 07L 6 35 25 CYM CYAN MOTOR 030040060 2 39BY501 4A 5 24 FROST MOTOR 030040060 2 39BY501 4A 5 24 CYM MAGENTA MOTOR 030040061 2 39BY501 3A 5 24 CYM YELLOW MOTOR 030040061 2 39BY501 3A 5 24 ZOOM MOTOR 030040023 2 42BYGH004 1A FOCUS MOTOR 030040023 1 42BYGH004 1A EFFECT WHEEL MOTOR 030040023 1 42BYGH004 1A IRIS MOTOR 030040080 1 42BY GHO04 7A STROBE MOTOR 030040080 2 42BY GHO04 7A PRISM ROTATION MOTOR 030040080 1 42BY GHO04 7A GOBO ROTATION MOTOR 030040024 1 42BYGH004 12A COLOUR WHEEL MOTOR 030040024 1 42BY GH004 12A ROTATING GOBO WHEEL MOTOR 030040121 1 42BYGH004 19A FIXED GOBO WHEEL 030040121 1 42BYGH004 19A PRISM MOTOR 030040120 1 42BYGH004 18A MOTOR DRIVE 230020135 1 DGITAL DISPLAY PCB 230020133 1 MOTOR DRIVE 230020136 1 NOTE You may order all parts of the PILOT 1200 besides the table listed above When ordering
8. 9 Rotation speed 5 160 167 Rotation speed 6 168 175 Rotation speed 7 176 183 Rotation speed 8 slowest i 184 191 Stop rotating 192 199 Reverse rotation speed 8 slowest 200 207 Reverse rotation speed 7 208 215 Reverse rotation speed 6 216 223 Reverse rotation speed 5 224 231 Reverse rotation speed 4 232 239 Reverse rotation speed 3 240 247 Reverse rotation speed 2 248 255 Reverse rotation speed 1 fastest 000 050 White 051 101 Prism 1 15 Prism 102 152 Prism 2 153 203 Prism 3 204 255 Prism 4 000 119 Index 0 540 120 127 Rotation speed 1 fastest 128 135 Rotation speed 2 136 143 Rotation speed 3 16 Prism Rotation 144 151 Rotation speed 4 152 159 Rotation speed 5 160 167 Rotation speed 6 168 175 Rotation speed 7 176 183 Rotation speed 8 slowest 11 20 Pilot 1200 EN doc 184 191 Stop rotating 192 199 Reverse rotation speed 8 slowest 200 207 Reverse rotation speed 7 208 215 Reverse rotation speed 6 216 223 Reverse rotation speed 5 224 231 Reverse rotation speed 4 232 239 Reverse rotation speed 3 240 247 Reverse rotation speed 2 248 255 Reverse rotation speed 1 fastest 000 050 White 051 101 Effect 1 17 Effects Wheel 102 152 Effect 2 153 203 Effect 3 204 255 Effect 4 18 Frost 000 255 Frosting from slight to strong 0 100 19 Pan amp Tilt speed adjustable by steps from Pan amp Tilt Speed 000 255 fast to slaw 20
9. D MOVEMENT Pan 540 Tilt 270 BEAM ANGLE 18 25 linear zoom CONTROL DMX512 20 channels plus 2 channels for high resolution Pan and Tilt 16 20 Pilot 1200 EN doc OTHER FUNCTIONS Adjustable Pan amp Tilt speed Projector usage time display lamp time display HOUSING Metal and composite plastic IP20 WEIGHT 48Kg SIZES See Drawings 6 3 S 668 17 20 Pilot 1200 _ EN doc 5 O lt a lt 2 x o 1noxwa 1noxwa ma MS jo o 10 19 VSLL asny CNVddOL C ZNVidOl 77 75 3401 1914 AO DT Y jo TTiVH ued 777 IIS o MaA r TVH TWH e J WJOJSUEJ in Jepmue i ued mv TWHued PT O O Cf U L V1N3SVW 5551810105 SIMOOZLIINH 702 3107 2 dvo V dvo Ud ZHOS pp gt Belea dams 201061 201011 JepOoue oN Pilot 1200 18 20 COMPONENT ORDER CODES NAME PART NO QUANTITY REMARK 040030054 1 200 240V TRANSFORMER 040030056 1
10. Pan Fine 000 255 Pan rotation in 16 Bit precision e Tilt Fine 000 255 Tilt rotation in 16 Bit precision 22 Control 000 170 Lamp ON 171 255 Lamp OFF after 10 seconds or over 12 20 Pilot 1200 EN doc LED DISPLAY Green ON DMx signal OK or Slave OFF No signal Flash DMX error Red Medium flash Menu mode Fast flash software cpu error Both ON Address mode Flash in turn Master mode CHANGING BELTS Pan s belts Free 2 screws on Pan assembly s maintenance door and open the door change the belts close the door and fasten the screws Base a Pan assembly s Tilt s belts maintenace door The common users replacing the belts is not recommended Screws Open door 13 20 Pilot 1200 EN doc MAINTENANCE If the projector s lens becomes damaged or broken it should be replaced If the lamp becomes damaged or deformed in any way it must be replaced If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once aged lamps run to the extremity of their life might explode If the projector does not function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specification Should these be damaged call a qualified technician before replacement The projector has thermal protection device that wil
11. aused by transportation consult your dealer and do not use the unit Any damage caused by improper use will not be assumed by the manufacturer and or dealer ACCESSORIES THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR G clamps 2 PCS XLR cable with 3 pin plug and socket 1 PCS Safety cord 2 PCS Spare gobos 4 PCS This manual 1 PCS Q clamps Options 2PCS INTRODUCTION Thank you for purchasing our product PILOT 1200 PR 2900 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PILOT 1200 is an innovative projector with an elegant housing which complies to CE norms and standards and uses international protocol DMX 512 The projector uses MSR 1200W discharge lamp and high quality optical system which produces bright and beautiful light beam and has 60 output lumen more than the similar products with the same power consumption The projector features effects of strobe frost light mixed colours and rainbow so it is suitable for applications in TV station singing and dancing stage nightclub etc 2 20 Pilot 1200 EN doc SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation consult your dealer and do not u
12. ch the lamp glass with bare hand The projector should always be installed with a secondary safety fixing A safety cord is supplied for this it should be attached as shown in installing the projector section The lamp used in this projector is an MSR 1200W SA DE discharge lamp After switching off don t attempt to restart the projector until lamp has cooled this will require approx 15 minutes Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector But occasional breaks will prolong the life of the lamp and projector Never run the projector without a lamp There is no user serviceable parts inside the projector do not open the housing and never operate the projector with the covers removed Always disconnect from the mains when the device is not in use or before cleaning it or before attempting any maintenance work If you have any questions don t hesitate to consult your dealer or manufacturer 3 20 Pilot 1200 INSTALLING THE PROJECTOR 4 HOLES FOR SAFETY CORD PASSING THROUGH Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp Hang the fixture on the structure and fasten the screws attached to each clamp Watch the WARNING on the underside of the base as shown above To ass 2 SAFETY CORDS throuqh 4 HOLES fo
13. cs at least once every 20 days and clean the internal optics at least once every 30 60 days Do not use any organic solvent e g alcohol to clean the reflector mirror dichroic colour filters or housing of the apparatus TROUBLESHOOTING PROBLEM POSSIBLE CAUSE ACTION The projector doesn t switch on The power supply is not present The lamp doesn t work Check the fuse on the power socket Replace the lamp The lamp comes on but the projector doesn t respond to the controller Wrong DMX configuration and or start address Defective DMX cable Make sure that the projector is correctly configurated Replace or repair the DMX cable The projector only functions intermittently The fan has failed Make sure the fan is working and not dirty Defective projection The lens is broken Dust or grease on lenses Check the lenses are not broken Remove dust or grease from the lenses The projected image appears to have a halo Installation of the lamp is not correct Dust or grease contamination on the optics Make sure the lamp is installed correctly Carefully clean the optical group lenses and the projector components The beam appears dim Dust or grease contamination on the optics The lamp is at the end of its life Check the optics is clean Replace with a new lamp of the specified type and rating 14 20 Pilot 1200 EN
14. l switch off the projector in case of overheating should either of these operate check that the fans are not blocked and if they are dirty clean them before switching on the projector again Check that the fans are operational if not call a qualified technician Any maintenance work should only be carried out by qualified technicians LUBRICATION To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing it is recommended that the bearings for the rotating gobos and the 2 shafts for the focusing lens holder be lubricated periodically preferably every two months Use only high quality high temperature resistant grease instead of any type of oil When lubricating the bearings a syringe with a fine needle is the easiest way to introduce the grease to the bearings around each gobo KEEPING THE PROJECTOR CLEAN To ensure the reliability of the projector it should be kept clean It is recommended that the fans should be cleaned every 15 days The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output Do NOT use any type of solvent on dichroic colour filters Cleaning frequency depends on the environment in which the fixture operates damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics A soft cloth and typical glass cleaning products should be used in cleaning It is recommended to clean the external opti
15. ls They are listed in the following table CHANNEL FUNCTION DMX DESCRIPTION 000 009 Shuttering 010 024 White 025 039 Strobe 1 slowest 040 054 Strobe 2 055 069 Strobe 3 070 084 Strobe 4 085 099 Strobe 5 100 114 Strobe 6 115 129 Strobe 7 1 pue 130 144 Strobe 8 145 159 Strobe 9 160 174 Strobe 10 175 189 Strobe 11 190 204 Strobe 12 205 219 Strobe 13 220 234 Strobe 14 235 249 Strobe 15 fastest 250 255 White 2 Dimmer 000 024 White 025 255 Dimming from light to dark 0 100 Linearly adjust iris from large to small 2 0005259 0 wholly rem 100 wholly closed 000 031 White 032 063 Gobo 1 064 095 Gobo 2 096 127 Gobo 3 128 159 Gobo 4 160 167 Rotation speed 1 slowest 168 175 Rotation speed 2 a red URS 176 183 Rotation speed 3 184 191 Rotation speed 4 fastest 192 223 Stop rotating 224 231 Reverse rotation speed 1 slowest 232 239 Reverse rotation speed 2 240 247 Reverse rotation speed 3 248 255 Reverse rotation speed 4 fastest 5 Pan 000 255 Pan rotation 6 Tilt 000 255 Tilt rotation 7 Focus 000 255 Linearly focusing 8 Zoom 000 255 Zooming with spot from large to small White 000 024 Note stay 5 seconds while DMX value is 5 6or 7 the function reset perform 025 030 White colour filter 1 031 036 Colour filter 1 037 042 Colour filter 1 colour filter 2 043 048 C
16. olour filter 2 3 reer ep 049 054 Colour filter 2 colour filter 3 055 060 Colour filter 3 061 065 Colour filter 3 colour filter 4 066 071 Colour filter 4 072 077 Colour filter 4 colour filter 5 078 083 Colour filter 5 084 089 Colour filter 5 colour filter 6 10 20 Pilot 1200 EN doc 090 095 Colour filter 6 096 101 Colour filter 6 colour filter 7 102 107 Colour filter 7 108 113 Colour filter 7 white 114 121 Rotation speed 1 fastest 122 129 Rotation speed 2 130 137 Rotation speed 3 138 145 Rotation speed 4 146 153 Rotation speed 5 154 161 Rotation speed 6 162 169 Rotation speed 7 170 177 Rotation speed 8 slowest 178 191 Stop rotating 192 199 Reverse rotation speed 8 slowest 200 207 Reverse rotation speed 7 208 215 Reverse rotation speed 6 216 223 Reverse rotation speed 5 224 231 Reverse rotation speed 4 232 239 Reverse rotation speed 3 240 247 Reverse rotation speed 2 248 255 Reverse rotation speed 1 fastest 10 CYM Cyan 000 255 Cyan 0 100 11 CYM Yellow 000 255 Yellow 0 100 12 CYM Magenta 000 255 Magenta 0 100 000 050 White 051 101 Gobo 1 13 Rotating Gobo 102 152 Gobo 2 153 203 Gobo 3 204 255 Gobo 4 000 119 Gobo index 0 540 120 127 Rotation speed 1 fastest 128 135 Rotation speed 2 136 143 Rotation speed 3 144 151 Rotation speed 4 152 15
17. r safety Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of PILOT 1200 WARNING 1 Unlock the PAN and TILT before the 15 application of projector for safety 2 The projector MUST be lifted or carried by the HANDLES instead of clamps FITTING THE LAMP BULB PST Lock tilt before fitting replacing the lamp Loosen 2 M5 screws and open one of the rear covers you can see the structure as shown in the figure above Loosen 2 nuts at the both ends of lamp and take out the worn out lamp Suggest to free one end after another Fit new lamp and fasten 2 nuts at the both ends of lamp Notes don t touch the bulb of the new lamp with bare hand so as not to influence the beam output the PST pumping stem tip off on the bulb facing the rear cover with fans perpendicularly and being not in the beam s way is a must and aids cooling Close the rear cover and fasten 2 M5 screws WARNING The HMI series are high pressure lamps with external igniters 2 Care should always be taken when handling these lamps Always read the manufacturers Instructions for use enclosed with the lamp 4 20 Pilot 1200 EN doc POWER SUPPLY MAINS Connect the power cord as follows L live brown E earth yellow green N neutral blue Use the plug provided to connect the main
18. s power to the projector paying attention to the voltage and frequency marked on the panel of the projector It is recommended that each projector be supplied separately so that they may be individually switched on and off IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards Power consumption of the PILOT 1200 is 1628W CONTROL CONNECTIONS 3 PIN gt DMX OUT DMX IN 5 PIN Connection between controller and projector and between one projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Connection to and from the projector is via cannon 3 pin which are included with the projector or 5 pin XLR plugs and sockets The XLR s are connected as shown in the figure above Note care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The PILOT 1200 accepts digital control signals in protocol DMX512 1990 Connect the controller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below
19. se the apparatus The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other liquids The projector is not designed or intended to be mounted directly on to inflammable surfaces X The projector is only intended for installation operation and maintenance by qualified personnel The projector must be installed in a location with adequate ventilation at least 50cm from adjacent wall surfaces Be sure that no ventilation slots are blocked Do not project the beam onto inflammable surfaces minimum distance is 5m 5m E Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle and or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord Keep the lamp clean Do not tou
20. y press button UP and DOWN you can set the address press button ENTER to confirm 6 20 Pilot 1200 EN doc FUNCTIONS DISPLAY AGG DISPLAY ADDR ADDR AAG appr 001 I 7 PAN ANTI CLOCKWISE ROTATION SWITCH MODE 1 RESERVED OFF CONTINUE 7 20 Pilot 1200 __ EN doc i p MASTER 2 RESERVED DISPLAY 0 255 FROM LIGHT TO DARK 1 0 255 FROM DARK TO LIGHT TIME HOUR MEANS 1 HOUR 8 20 Pilot 1200 _ EN doc ERRORS DISPLAY In the course of launch PILOT 1200 examines automatically whether there are errors and if there are it will display information as follows INFORMATION ERRORS Er02 Sensor 1 temperature too high Er04 Lamp error Er05 EEPROM error Er06 Sensor 2 temperature too high Er09 Gobo rotation reset error Er10 Gobo change reset error Er11 Effect wheel reset error Er
Download Pdf Manuals
Related Search