Electric Range
Contents
1. lectric Range installation manual t K 3 SN 100 Recycled Paper s made with 100 recycled p imagine the possibilities Thank you for purchasing this Samsung product Manual Installation _30 Oven _USA_DG68 00108G 03_EN indd 1 2014 02 20 M 1 54 15 oOelore you pegin ANTI TIP DEVICE WARNING To reduce the risk of tipping the appliance the appliance must be warning Secured by properly installed anti tio devices packed with the appliance a Achild or adult can tip the range and be killed b Install the anti tio device to the structure and or the range at rear right or rear left s gt of the range bottom c Engage the range to the anti tio device by leveling leg at rear right or rear left of the range bottom d Re engage the anti tip device if the range is moved e See installation instructions for details f Failure to do so can result in death or serious burns to children or adults ABOUT THIS MANUAL READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY Important note to the installer e Read all instructions contained in these installation instructions before installing range e Remove all packing materials from the oven compartments before connecting the electrical supply to the range e Observe all governing codes and ordinances e Be sure to leave these instructions with the consumer Important note to the consumer Keep these instructions for the local electric2. e Phillips Screwdriver Flat Screwdriver Pencil Level What s included with your range ERE Template Anti Tipo Bracket Screws 4 ea What s not included AONVd JHL TIVLSNI OL ONIdVdsadd 8 NIDA NOA 340434 HLO 4 Wire Cord or 3 Wire Cord Strain Relief UL Approved 40 or 50 AMP For Conduit Installation Only English 3 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 3 2014 02 20 00 1 54 16 CHECKING THE INSTALLATION SITE Clearances and dimensions To install the range refer to the following figure For installation in CANADA a Free standing range is not to be installed closer than 12mm from any adjacent surface A CAUTION This range has been designed to comply with the maximum allowable wood cabinet temperatures of 194 F Make sure the wall covering countertops and cabinets around the range can withstand the heat up to 194 F generated by the range If not discoloration delamination or melting may occur H Ss 1 ne Uy Yj SE 28 1 5 24 9 10 a 36 36 4 5 a 25 9 10 L 46 1 5 47 f Ba A Cabinet opening Fae pe 30 For U S A 2 r ee 30 31 For CANADA i B Acceptable ba electrical outlet area Minimum dimensions IMPO RTANT To eliminate the risk of burns or fire caused by reaching over heated surface units cabinet storage space located above the surface units should be avoided If cabinet stora
3. your main range disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your oven according to governing codes could result in a hazardous condition If there are no local codes your range must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 7O Latest Edition You can get a copy by writing d4AMOd AHL ONILOANNOO Z0 National Fire Protection Association Batterymarch Park Quincy MA 02269 Effective January 1 1996 the National Electrical Code requires that new construction not existing utilize a 4 conductor connection to an electric range When installing an electric range in new construction follow Steps 2 and 3 for 4 wire connection You must use a 3 wire or 4 wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If the electrical service provided does not meet the above specifications have a licensed electrician install an approved outlet Use only a 3 conductor or a 4 conductor UL listed range cord These cords may be provided with ring terminals on wire and a strain relief device A range cord rated at 40 amps with 125 250 minimum volt range is required A 50 amp range cord is not recommended but if used it should be marked for use with nominal 138 diameter connection openings Care should be taken to center the cable and strain relief within the Knockout hole to keep the edge from dam
4. NG To reduce the risk of tipping the appliance must be secured by properly installing the Anti Tip device packed with the appliance e Refer to the installation instructions supplied with the bracket e Unless properly installed the range could be tipped by stepping or sitting on the door Injury may result from spilled hot liquids or from the range itself approximately 24 32 16 5mm NOTE To install Anti Tip bracket release the leveling leg A minimum clearance of 21 32 16 5mm is required ASNVd AHL ONITIVLSNI 0 Screw must enter wood or between the range bottom and the concrete kitchen floor 1 Locate the bracket using the template The Anti Tip bracket is packaged with a template The instructions include information necessary to complete the installation Read and follow the instructions on the sheet template for range installation 2 Level the range Level the range by adjusting the leveling legs with a wrench MAMMA AY 4 Wy Wil Raise range aa Lower range i JI Leveling leg English 11 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 11 2014 02 20 00 1 54 20 3 Check your adjustments Use a spirit level to check your adjustments Place the level diagonally on the oven rack or surface cooktop and check each direction for level 1 Check direction 1 2 Check direction 2 If the spirit level does
5. aging the cable e Because range terminals are not accessible after range is in position flexible service conduit or cord must be used NOTE If conduit is being used go to Step 4 on page 9 ALL NEW BRANCH CIRCUIT CONSTRUCTIONS MOBILE HOMES RECREATIONAL VEHICLES AND INSTALLATIONS WHERE LOCAL CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL REQUIRE A 4 CONDUCTOR UL LISTED RANGE CORD English 5 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 5 2014 02 20 00 1 54 17 STEP 2 ACCESSING THE POWER CORD CONNECTION Remove the rear access cover and loosen the screw with a screwdriver The terminal block will then be accessible Terminal block Specified power supply cord kit rating Range rating watts Specified rating of oower supply cord kit Diameter inches of range connection opening 120 240 volts 120 208 volts amperes acne Sri Power cord Conduit 8 750 16 500 7 801 12 500 40 or 50A 13 8 11g English 6 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 6 2014 02 20 m 1 54 18 STEP 3 INSTALLING THE POWER CORD For power cord installations hook the strain relief over the power cord hole 18 s located below the rear of the drawer body Insert the power cord through the strain relief and tighten the device Conduit connection plate Strain relief e You must install the power cord with a strain relief e Attac
6. al inspector s use e As when using any appliance generating heat there are certain safety precautions you should follow e Be sure your range is installed and grounded properly by a qualified installer or service technician e Make sure the wall coverings around the range can withstand the heat generated by the range e To eliminate the need to reach over the surface elements cabinet storage space above the elements should be avoided e The range should not be placed on a base FOR YOUR SAFETY WARNING WARNING If the information in this manual is not followed exactly a fire or electrical shock may result causing property damage personal injury or death A WARNING Before beginning the installation switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel A WARNING This appliance must be properly grounded English 2 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 2 2014 02 20 00 1 54 15 oreoaring to Install ine range REMOVE PACKAGING Remove packaging materials Failure to remove packaging materials could result in damage to the appliance PREPARE TOOLS amp PARTS What tools you will need E a Adjustable Wrench Pliers 1 4 Nut Driver EEC E eo
7. ge is to be provided the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 beyond the bottom of the cabinets 30 minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet or 24 minimum when the bottom of the wood or metal cabinet is protected by not less than 1 4 flame retardant millooard covered with not less than no 28 MSG sheet steel 0 015 stainless steel 0 024 aluminum or 0 020 copper 15 minimum between the countertop and the adjacent cabinet bottom English 4 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 4 2014 02 20 00 1 54 17 connecting tne power STEP 1 MEETING ELECTRICAL CONNECTION REQUIREMENTS CAUTION CAUTION For personal safety do not use an extension cord with this appliance Remove house fuse or open circuit breaker before beginning installation This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as specified on the rating plate The rating plate is located above the drawer on the oven frame Fig 1 or Fig 2 We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician After installation have the electrician show you where
8. h the strain relief to the 13 8 opening in conduit connection plate Installing a 3 wire power cord a d4AMOd AHL ONILOANNOO Z0 A WARNING The neutral or ground wire of the power cord must be connected to the neutral terminal located in the center of the terminal block The power leads must be connected to the lower left and the lower right terminals of the terminal block 1 Remove the 3 lower terminal screws from the terminal block 2 Insert the 3 terminal screws through each power cord terminal ring and into the lower terminals of the terminal block Be certain that the center wire white neutral is connected to the center lower position of the terminal block 3 Tighten screws securely into the terminal block DO NOT remove the ground strap connection 4 Go to step 5 on page 10 and proceed with the installation English 7 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 7 Neutral terminal Ground strap NA 2014 02 20 m 1 54 18 Installing a 4 wire power cord WARNING WARNING The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block The power leads must be connected to the lower left and the lower right terminals of the terminal block The 4th grounding lead must be connected to the frame of the range with the ground plate and the ground screw Remove
9. n t show level on the oven rack or surface cooktop adjust the leveling legs with a wrench FINALIZING THE INSTALLATION e Move range close enough to the opening to plug into the receptacle e Slide range into position insuring that the rear left or rear right leg slides under the Anti Tip bracket The range will sit O away from the back wall when properly installed e Carefully tip the range forward to insure that the Anti Tip bracket engages the back brace and prevents tip over e Turn on the electrical power Check the range for proper operation as described in the user manual Anti Tip bracket Leveling leg DG68 00108G 03 English 12 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 12 2014 02 20 m 1 54 21
10. o this Step 4 depending on the number of wires e Wire used location and enclosure of splices etc must conform to good wiring practices and local codes 1 Loosen the 3 lower terminal screws from the terminal block Remove the ground screw and ground plate and retain them 2 Cut and discard the ground strap Do not discard any screws 3 Insert the ground bare wire tip between the range frame and the ground plate removed earlier and secure it in place with the ground screw removed earlier 4 Insert the bare wire white neutral tip through the bottom center of the terminal block opening 5 Insert the two side bare wire tips into the lower left and the lower right terminal block openings 6 Tighten the screws until the wire is firmly secured 85 to 50 inch lbs Do not over tighten the screws since it could damage the wires 7 Go to step 5 and proceed with the installation Ground strap pw cig Y By BY Wire tips A W ae et l j T AS Ground WITE Green STEP 5 REPLACING THE ACCESS COVER Replace the access cover on the range back To replace the wire cover insert double projections in the pockets located below the opening and tighten the screw English 10 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 10 2014 02 20 00 1 54 20 installing the range INSTALLING THE ANTI TIP DEVICE A WARNI
11. ons insert the strain relief not included into the conduit hole 11 s Then thread the conduit cord through the body of the strain relief and fasten the ring Reinstall the bracket Installing a 3 wire conduit e Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make the connection Connect wires according to Step 4 depending on the number of wires e Wire used location and enclosure of splices etc must conform to good wiring practices and local codes 1 Loosen the 3 lower terminal screws from the terminal blade Neutral terminal Ground 2 Insert the center bare wire white neutral tip through the bottom center terminal block opening On certain models the wire will need to be inserted through the ground strap opening and then into the bottom center block opening 3 Insert the two side bare wire tips into the lower left and the lower right terminal block openings 4 Tighten the screws until the wire is firmly secured 85 to 50 inch lbs Do not over tighten the screws since it could damage the wires White 5 Go to step 5 on page 10 and proceed with the Wire tips installation English 9 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 9 2014 02 20 00 1 54 19 Installing a 4 wire conduit e Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make the connection Connect wires according t
12. the 3 lower terminal screws from the terminal block Remove the ground screw and ground plate and retain them 2 Cut and discard the ground strap Do not discard any screws 3 Insert the one ground screw into the power cord ground wire terminal ring through the ground plate and into the frame of the range 4 Insert the 3 terminal screws removed earlier through each power cord terminal ring and into the lower terminals of the terminal block Be certain that the center wire white neutral is connected to the center lower position of the terminal block Tighten screws securely into the terminal block 5 Go to step 5 on page 10 and proceed with the installation Neutral terminal White I pane o W aN N A a Ground strana P id al a GROUND Ground plate 1 i i 1 D i 1 1 1 1 d i 1 1 1 l i 1 1 1 i 1 White Black srona gt I Screw Ground wire Green English 8 Manual Installation 30 Oven _USA_DG68 00108G 03_EN indd 8 2014 02 20 00 1 54 19 STEP 4 INSTALLING THE CONDUIT Remove the conduit connection plate from the rear of the drawer body and rotate it as shown below The conduit hole 11 s must be used 1 Prepare the conduit cord shown in Figure 1 2 Install the conduit cord as shown in Figure 2 Figure 1 d3MOd AHL ONILOANNOO Z0 Knockout surface Conduit connection plate For conduit installati
Download Pdf Manuals
Related Search