Opticstar PX-137 COOLAIR Setup Guide
Contents
1. Microscope Attachments In order to use the camera with a microscope one or more attachments must be used The attachments shown from left to right are C CS to 23mm x0 5 C CS to 23mm x1 C CS to 30mm and C CS to 30 5mm These attachments are not bundled with the Updated 02 10 2012 18 Specification Opticstar PX 137 COOLAIR Image sensor Sony IMX035 1 3 Exmor CMOS Quantum Efficiency 76 500nm Sensor type Progressive scan Pixel size 3 63umM x 3 63um Max Resolution 1280 x 1038 pixels Speed 25fps 1280x1038 5O0fps 668x512 Analogue to Digital Converter 12 bit ADC full 4096 range Full well capacity 15000e Read out noise 3e RMS Gain In hardware Exposure Range 1ms to 60 seconds Exposure Automatic or Manual Global shutter 4500 1 Gain 1X Clear no Infra Red cut off USB 2 0 480 Mb s USB 2 0 powered C CS Mount CICS to 1 25 included C to T thread M42 x 0 75 C to 23mm 30mm 30 5mm 1 8 meter long Computer requirements Microsoft Windows 32 bit or 64 bit XP Vista 7 8 USB 2 0 Bundled software ISCapture etAMCAP Windows drivers NO QI O OPTICSTAR Opticstar Ltd 87 Washway Road Sale Greater Manchester M33 7TQ United Kingdom 0044 0 161 969 9008 info opticstar com www opticstar com www opticstar ccd com2. ExpressCards run faster than PCMCIA CardBus cards due to the ExpressCard s superior speed of 2 5Gbit s 480 Mbit s through USB 2 0 per slot for comparison PCMCIA CardBus_ devices connected to a computer would share a total 1 06 Gbit s bandwidth Express type cards use a 34mm slot where PCMCIA CardBus cards use 54mm slots An ExpressCard should be connected directly to the computer and not via a PCMCIA CardBus card Please note that using an ExpressCard may still not solve any data bandwidth bottlenecks that are inherent in old computers Updated 02 10 2012 16 Opticstar PX 137 Opticstar Ltd 2012 Re Installing the Software Drivers DirectShow support can be removed or installed independently from the camera s software drivers Please refer to the section Installing Software for Windows DirectShow in this guide for details Re Installing the Software Drivers If the camera cannot be identified by Windows then it is possible that the software drivers have not been installed correctly or they have been corrupted In such cases it is best to uninstall the drivers This can be done from the Device Manager in Windows la File Acton View Help iga Eel H em Ge oe G Sy DELL S508 4 Computer Hom Disk dives BS Display adapters lj DVD CD ROM drives mem Floppy drive controllers z ta Human interface Devices Hg IDE ATASATAPI controllers gt Keyboards Fi Mice and other pointing devices Be bee
3. Windows desktop to run the program Running etAMCAP The camera will be identified as Opticstar PX 137C or Opticstar PX 137M Select the camera from the Devices menu EtAMCAP can be used as a general purpose program to capture video in AVI format EtAMCAP can be used to capture video in AVI format It cannot capture single frames In order to capture single frames as well as video please use ISCapture Image Resolution The camera can operate in a Porere bssan number of image resolutions Foma From the Options gt Video Resolution Capture Pin menu select the C 1280x1040 camera resolution iaa C 668 514Einning e 1280 x 1040 f _ F 1280 X 800 Co B40 512 SW Binning e 668 x 512 Binning e 640 x 512 SWBinning Updated 02 10 2012 I Opticstar PX 137 Opticstar Ltd 2012 Properties The camera can be configured from ay the Options gt Video Capture Filter Exposure menu m s ton j1 5 Automatic Exposure Time toe E te AE Enable stands for Automatic Exposure When auto exposure is Auto White Balance used the user cannot specify the Gan 1 00 exposure time However it is still GG 1 possible to add a bias by increasing a e or decreasing the Target value y ae Likewise the Gain value is not user FZ Enkancameni Enable definable in auto exposure mode danii J si dalam Manual Exposure Time
4. ee pea E To set the exposure time manually aE simply un tick the AE Enable option CHR VFip I Mom In this mode the time can be set in milliseconds and Gain can also be set The Target value cannot be set in Manual exposure mode ox Cancel Colour Settings For colour cameras the colour settings of the captured images can be modified by the slider bars Additionally the values for Gamma Contrast and Saturation can be specified Camera Speed The camera speed can be set to High Normal or Low This refers to the speed at which the camera sends the data to the computer At lower speeds the image quality is better but at higher speeds the camera downloads the data quicker Other Settings The orientation of the captured images can be inverted or reflected by the H Flip and V Flip options The Mono option produces monochrome images rather than colour Updated 02 10 2012 12 Opticstar PX 137 Opticstar Ltd 2012 ISCapture ISCapture is a more advanced software application that can be used to control the camera capture single frames or video perform image processing and take image measurements It can also be used for a wide range of applications including microscopy IS apture Installing I SCapture 1 To install TSCapture navigate to the ISCapture folder on the CD and open the ISCapture_setup exe file Welcome to the SCapture Setup Wizard This wil instead SCanture 2 6 on your computer i
5. operating systems For the PX 137M monochrome the drivers are situated on the CD in Drivers PX 137M 64 bit for 64 bit operating systems and in Drivers PX 137M 32 bit for 32 bit operating systems e 2 Update Driver Software 13MP color camera Browse for driver software on your computer Search for drer software m this locatione DA Cpticstar PRLI OriwverstPX 1370 64 bit x Inchude subfolders Let me pick from a list of device drivers on my computer This fist wall show installed diser software compatible wath the devece and all driver oftware in the same category as the devece Net Cancet 8 Windows may display a warning message Simply select Install this driver software anyway to continue Update Dri Setters LAMP colar carne Installing driver software a HE Geel gels Updated 02 10 2012 9 Opticstar PX 137 Opticstar Ltd 2012 9 Windows will display Installing driver software and will proceed with the installation Kewl Update Driver Software Optecstar PX 137C Windows has successfully updated your driver software Windows has finished installing the diser software for this device Opticstar PX 13TC ee Ts j LL 10 Windows will copy the installation files and display the following message Windows has successfully updated your driver software 11 If Windows asks to restart the computer please do so Verifying Successful Ins
6. recommended that you cose al other apatoa before COnGnuin Chick Meat ana of Cancel to eict Seto 2 Windows will display Welcome to the ISCapture Setup Wizard Click the Next text gt cancel button to continue 3 During installation you will be asked to select the location where the program will be installed and whether to install video processing software Please select all the additional software video components by ticking the appropriate options E Setup Capture bocce LE EE D Setup Capture fecha Select Destination Location fn TY Select Components mT Tip Where should SCaptre be reime obese Wired comporents shad be ibaiei Tamanan Sect See components pou want bo insiel Gear te components you do not want ia b inona hirer arei l ehrn h y reiil Gick Mext when you sre resdy bo continue Te conbree cick Mesi H you would Hop to select a different boidar cick Browse Custom ramlan c Program Fies x65 25Capture i amen 5 Scare Presa Y hoffus 2 L1 feb bees Fini veo codec only if poo would lee to Shes record vdeo F ee 1 1 9 ki oi bad on ME 4 eS format any if y a Be be recond vaea Shes AS beset 13 5 Mil of free disc space is required Current selection negquines a9 lest 15 5 Mi of dick spare lt Beck Next gt Canc lt Back Pear gt anced Once the installation is complete SCapture can be run by clicking on the Windows Start button and selecting ISCapture
7. HE Monitan B Wchanst aipin a Network adapters ic a EE a Jap Other devices Taina wt oe 3 E Portabl Update Drrver Software ay har npr rm Asi Process Disable 4 Sound Uninstall JAS Storage fai Sytem Scan for hardware changes LaunchestheUpdd Properties Click on the Start button on the Windows desktop and from Settings gt Control Panel select Device Manager The camera should appear in the list under Imaging devices 1 Right click on the Opticstar PX 137 entry 2 On the pop up menu and select Uninstall 3 If Windows asks to restart the computer select Yes and continue When the computer restarts please re install the software as normal To re install the drivers please follow the instructions in the Installing Software Drivers for Windows section in this guide Updated 02 10 2012 17 Opticstar PX 137 Opticstar Ltd 2012 Support For support regarding the PX 137 please email Opticstar at info opticstar com Other Software There is some freely available third party software that may be of interest to some users Please note that Opticstar cannot guarantee the suitability the software e Deep Sky Stacker http deepskystacker free fr e RegiStax http www astronomie be registax These programs can be used to post process video files captured in EtAMCAP and ISCapture They can stack align and enhance multiple AVI frames into a single high quality master image
8. Opticstar PX 137 COOLAIR Setup Guide OPTICSTAR Opticstar PX 137 Opticstar Ltd 2012 CONTENTS DVEROCUICE ON a PAEA E A AAA 2 Software Support cscssscsssscscsesssscsesessssrorsesenscoraesenscoraesenscseacsenseseacsessaseaesesenseoraesenseoraesenscoraesensaseacsensasearseseasreraesenseeraeseness 2 Package C OMENS siiis ANNAE ARARE EANAN A A S 2 SOCIO GC Cf ee 2 Camera INS tall AG OM sscscsccscecisajcucscaccdescscszaacwasuceaquacstiesaesavasecssacseauscuaeyavazesienavesucasvavsuceavsauasesseqavsderstieieausaisiavsierianereinanvansaeaainaiaiel 3 Installing Software for Windows DirectShow cccsssssssssssssssssesssssssssssssccessesesesesesacacaeesesesesesecaeaeanseseseseseeatanananas 4 Installing Software Drivers for WINdoOwWS scssssessesseseessssescaeeseeeceeaeseseeetaeeseeecanaesesecanasseseeatanseseeetanseseeetanaesesetanas T Veniying SUCCESSIULING taNatiO Nsa a i a aia da E a iA E e Sacre 10 acaciae CCUG i AE A evs cau E O AE O N O A N 11 RUNNING CAMO AP ironien NA ourse saN SEDEF EENEN EAE SAAE SNEEK FEAE SANESA EESE NEEE ONEEN NESE AREA E DEANE ONENE 11 mage RESONI i ee 11 Ae A o a a E A A A A A 12 Manual Exposure TiM6 ccssssssssrsssrsssssecssseeseseeseseesecesecassecaesesseseesecaesecassecaeseeaeseesesassesassecasseeaesereseeseeassetasseeansntanes 12 Colour Sens serne ee eee 12 Camon opo aa E E E E E san ansatnteoanaest 12 Oer SUNOS aan esos cnc ccascsas cass sacceaseaestucsene tecscosceesdonscsase cans ta
9. X 137M monochrome are advanced astronomy video cameras that excel in planetary lunar and solar imaging The camera is also suitable for microscopy when fitted with an appropriate attachment Please note that for solar photography the camera should be used only with an appropriate solar telescope and or solar filters The PX 137 incorporates the advanced Sony IMX035 sCMOS scientific CMOS sensor that outperforms CCD sensors such as the Sony ICX618 CCD by a significant margin The PX 137 achieves frame rates of up to 25 frames per second FPS at full resolution 1280x1038 pixels or up to 50 FPS at 668x512 pixels Software Support Two software applications are bundled with the camera etAMACAP and ISCapture EtAMCAP works under Microsoft s DirectShow model ISCapture supports the camera natively offering image processing and measurement functionality Package Contents The following items are included in the package Opticstar PX 137 video camera with removable C ring In situ USB 2 0 cable CS to 1 25 telescope adapter Software CD Setup Guide this document System Requirements The minimum computer system requirements are the following e Windows 32 bit or 64 bit XP Vista 7 8 with the latest Service Pack e USB 2 0 port for the camera Updated 02 10 2012 2 Opticstar PX 137 Opticstar Ltd 2012 The camera does not incorporate any optics and therefore it cannot reach focus by itself A C CS mounted l
10. ens must be used with the camera or it must be attached to a telescope with the nosepiece adapter that is included with the camera To attach it to a microscope please use an appropriate attachment Camera Installation There are four sets of software to install in order to add support for the PX 137 camera to Windows They should be installed in the following order 1 Windows DirectShow software for the PX 137 2 Windows software drivers for the PX 137 3 ECAMCAP application software for using the camera 4 ISCapture application software with more advanced functions and better usability The first step is to install software that makes the PX 137 compatible with Microsoft s Windows DirectShow model Such compliance allows the PX 137 to be used with etAMCAP and possibly with other third party applications cases the anti virus software should be temporarily disabled Otherwise when prompted add the installation files to the trusted list D Anti virus software may attempt to block the installation In such The installation of the software should be carried out by a user with Windows administrator permissions Otherwise the installation may fail D Please ensure that the camera is not connected to the computer yet Updated 02 10 2012 3 Opticstar PX 137 Opticstar Ltd 2012 Power up the computer or restart Windows but do not attach the camera to the computer yet Once on the Windows Desktop please foll
11. es cog Disk drives k Display adapters pig DVD CD ROM drives gg IDE ATS ATAPI controllers gt Keyboards Ms Mice and other pointing devices E Monitors F g Network adapters wp lomega Virtual Ethernet Adapter ue Microsoft Virtual WiFi Miniport Adapter EP NETGEAR WPN3L1 RangeMax TM Wireless PCI Adapter i Realtek PCle GBE Farnily Controller fm Other devices 3 SS Ports C Update Driver Software E Process Disable amp Sound Uninstall i System i Univers Scan for hardware changes ih Properties Launches the Update Driver Software Wizard forth 6 A message will appear giving two options Select Browse my computer for driver software In the following step direct Windows to the Drivers folder on the CD How do you want to search for driver software Search automatically for updated driver software Windows wall search your computer and the int met for the lebest driver software for your device unless you ve dissbled this feature in your device installation satinga Browse my computer for driver software Locate and install dover software manually Cancel Updated 02 10 2012 8 Opticstar PX 137 Opticstar Ltd 2012 7 Navigate to the appropriate Drivers folder and click Next to proceed For the PX 137C colour the drivers are situated on the CD in Drivers PX 137C 64 bit for 64 bit operating systems and in Drivers PX 137C 32 bit for 32 bit
12. eseneseecsens essay csesseascorctc 12 A 6 eee 13 TUL ire SCADE enpererereneer treet trier ner renter arse er tri EA 13 Camera C Omi ON sa AAA 14 FOUDIES ROONG iann a A A E N 16 USB TS UU NCES VES vacinar iie a a i a e eiaa a aiiai i a a eeni 16 AA o A A E A A ee eee ee ee 16 Re Installing the Software Drivers csscsssssescsssessscsseseeseesesesecacseseeecasaeseseseeaseseeecasseseseeasaeseeeeanasseseeetanaeseeeeanaeses 17 Relnstaling the Sonware DIIVETS sisusse aaea eaaa Ea eee secon E eaaa a Aaaa ENa soe usu ak 17 SUD e g AA EE E E E EE EEE E E E EE 18 Oher SONWANE aienea eaii araisa aA ar rE rarna Ear eaan 18 Microscope ATLACIINGING ssn and 18 CAUTION 1 Please read and follow the installation instructions on the following pages for a trouble free installation Do not drop your camera as this can result in serious damage Only use the supplied power supply unit if you camera comes with one 4 Do not point the camera to a bright light source like the Sun without the appropriate filters as this will damage the sensor 5 Disconnect the camera from the computer when not in use 6 Treat the camera glass window with the same care as you would of a photographic lens Manufacturer s Warranty This product has a 1 year back to base warranty For after Sales support please contact Opticstar at info opticstar com Updated 02 10 2012 l Opticstar PX 137 Opticstar Ltd 2012 Introduction The PX 137C colour and P
13. from the programs list Alternatively click the appropriate icon Updated 02 10 2012 13 Opticstar PX 137 Opticstar Ltd 2012 Camera Control Run ISCapture with the camera connected to the computer On the top panel of the application the camera will be identified as Opticstar PX 137C or Opticstar PX 137M The camera will start running as soon as SCapture opens B Opticstar Fi Ire Capiure Browse Image 1 Frate Fine 3659 FPS Main Control Frame Speed e Horma Hagin Data Vaeth Oe GEN Color Enhancement Monochrome Presse Rescadin ligiga i Capture Resoktion 2801 Oe T commee Mop Expasure Control olor Control Fluorescence File Savi T F T T T Parametar Some of the frequently used camera controls are visible on the left hand side panel of the program Such controls include data width and camera speed Selecting 16 bit data width will capture higher quality images at a slower frame rate It will also result in larger video files Selecting high speed will result in larger video files The image resolution can also be set in eee the Preview Resolution and Capture 2804038 7 Resolution fields By default they are A m TA both set at 1280 x 1038 pixels al Capture Resolution 42804 038 Updated 02 10 2012 14 Opticstar PX 137 Opticstar Ltd 2012 Selecting the Stop button will cause the camera to Hl Stop sto
14. orescence P File Save P Parameter p Opticstar PX 137 Opticstar Ltd 2012 Troubleshooting If you experience difficulty in installing the camera software and drivers this may be due to a number of reasons related to your computer operating system and other devices already connected to it The following sections outline the most common problems and suggest ways in which you should be able to solve them Please also refer to the documents in the Articles folder on the CD USB Requirements Please ensure that your computer runs Windows XP Vista 7 8 or later has the latest updates from Microsoft and also has USB 2 0 ports The PX 137 camera will not work with USB1 1 If your computer has USB1 1 ports you will need to obtain a PCI USB2 0 type card if you have a desktop or an Express USB2 0 card if you have a laptop The ExpressCard will need to be fully supported by your computer in some entry level laptops full ExpressCard and PCI USB2 0 support in not fully implemented If you have a desktop try both the USB ports on the front and back of your PC if the camera is not recognised on a particular USB port USB ports attached directly to the motherboard are more efficient Please note that PCMCIA USB2 0 cards typically do not provide the full USB2 0 bandwidth and will not work with the PX 137 camera Express Card In some cases it may be possible to resolve such issues by fitting an ExpressCard with USB2 0 ports to your computer
15. ow the instructions in the following sections that describe how to install the software starting with DirectShow support Installing Software for Windows DirectShow Please follow these instructions for all versions of Windows 32 bit amp 64 bit XP Vista 7 8 1 Insert the CD that comes with the camera in the CD DVD drive 2 Navigate to the DirectShow folder on the CD and run Opticstar_PX 137C_DirectShow exe for the PX 137C colour model or Opticstar_PX 137M_DirectShow exe for the PX 137M monochrome model 3 A message will appear Welcome to the PX 137 Camera Directshow Plug in Setup Wizard Click on the Next button to continue 45 Setup Opticster PX 137C Directshow and Twain Plug in a l faecal Welcome to the Opticstar PX 13 7C Directshow and Twain Plug in Setup Wirard This vl instal Ootestar PX 137C Directshow and Taan Pugin Veron LI en our computer tip recommended that you dose al other appications before corre Chock Next to contrive or Canoe to est Setup 4 Windows may display a warning message such as Windows can t verify the publisher of this driver software Select Install this driver anyway to continue Updated 02 10 2012 4 Opticstar PX 137 Opticstar Ltd 2012 e Windows Security x Windows can t verify the publisher of this driver software Don t install this driver software You should check your manufacturer s website for updated driver software for your device g
16. p capturing data The button will change to Play Clicking the Play button will start playing video again P Play The Capture button will write the video data directly e to the computer s hard disk as an AVI file if capture The number of frames captured can be set in the File Save menu The file name and the folder can also be specified there Similarly the exposure time can be set in the Exposure Control menu When used in astronomy the exposure time should be set manually The time must be specified in milliseconds ms seconds s and minutes m The appropriate length of the exposure time depends on the brightness of the target to capture the size of the telescope and the focal ratio of the telescope The Gain function boosts the sensitivity of the camera It is an electronic amplifier that increases the strength of the captured image It is possible to reduce the required exposure time by increasing the Gain value For full instructions regarding ISCapture please refer to the OS _ISCapture pdf user manual on the CD It is situated inside the ISCapture folder Updated 02 10 2012 15 Exposure Control Color Control Fluorescence File Save T De er ee F Parameter B Opticstar PX 137C es S n i Y Capture Browse Image i Frame Fate EJ FPS Wain Control Be Exposure Control Auto Exposure Manual Exposure o Exposure Gain de 03B i Color Control P Flu
17. s of bandwidth and power Please use one of the ports connected directly to the motherboard if possible Such USB 2 0 ports are typically situated at the back of the computer 1 Insert the CD in the drive 2 Connect the camera to a USB 2 0 port on your computer 3 Windows may try to locate drivers for the camera automatically Click Skip obtaining driver software from Windows Update The drivers should be installed manually Driver Software Installation Installing device driver software 1 3MIP color camera t Searching Windows Update Obtaining device driver software from Windows Update might take a while Skip obtaining driver software from Windows Update 4 The following message will appear Ignore the message and open the Windows Device Manager to install the drivers manually lL Device driver software was not successfully installed gt Click here for details If you are not sure how to access the Device Manager on your computer press F1 on the keyboard while on the Windows desktop to access the Help and Support Center Once there search for Device Manager Updated 02 10 2012 7 Opticstar PX 137 Opticstar Ltd 2012 5 The camera will be identified as 1 3mp camera in Device Manager Select this entry by right clicking on the mouse and select the Update Driver Software option File Action View Help C A T ee PRs 1 Pei gt gf Computer 2 Digital Media Devic
18. start the computer later 7 Finally if Windows asks to restart the computer select Yes If at any stage you wish to remove DirectShow support you can do so from the Windows Control Panel independently of the camera s Windows software drivers Click the Add Remove Programs icon on XP or Programs and Features on Vista 7 and remove the entry headed PX 137 Di tSh a Irec OW G Jea t Cmi Pan Peeper b Pecari and Features r f4 P Pans J Epu p Conin PeH Hime s Linta Of change amp pregi Verve imfaled updater Po anita a program pit ct from Bhe iit and then chick Uninstall Change or Repar al Tia Ari Membre cet ce ott z nange Uninstall H Name i Pubaher hamein a MEDR iD SP ee Manialt Eorna ibati 2 S00 20 F RESTS Lhe Caran 1448 11 a ihebelouty IE Chet Labe SAT Sl New Aprono COOK ac 14 ne ed Nenegad 10822 eOe TSC Dieectiher Version 2 0 SOL lipta PX TiC tiho erin 2 1 LES ol Ophucstae PX TOM Dheectshow Version 2 1 SOL n iiaii PX LIE Dreo and Ta ai tae ED eni P a Opt ster Views ETE Unima LATS FL 10C Versa 0 id 2 PL TM Deerttains Vere 2 Se LL QeickTime Appie Inc HOW I Opci Hir D een F Coppo bri wasee CET am Soy be Updated 02 10 2012 6 Opticstar PX 137 Opticstar Ltd 2012 Installing Software Drivers for Windows Desktop computers have USB 2 0 ports on the front and the back Sometimes the ports at the front are not fully USB 2 0 compliant in term
19. t Install this driver software anyway Only install driver software obtained from your manufacturer s website or disc Unsigned software from other sources may harm your computer or steal information See details 5 The install program will ask if any additional video software Should also be installed Since the camera will typically be used in video mode the response to this should be yes Select all the options and click the Next button to continue J ee Se a RT ee ee fn The on Se el oe ee Seto Lhoticstar PA j tie iret ait a lain E Capen Fea eraran AT e i er tja iner ao Ea E Ld Hoesen T Lod Select Components Which components should be installed Select the components you want to install dear the components you do not want to install Click Next when you are ready to continue Full installation Twain Driver V Directshow Driver Current selection requires at least 5 0 MB of disk space Updated 02 10 2012 5 Opticstar PX 137 Opticstar Ltd 2012 6 Eventually Windows will display Completing the Opticstar PX 137 Click Finish to continue j5 Setup Opticstar PX 137C Directshow and Twain Plug in Egi Eg Completing the Opticstar PX 137C Directshow and Twain Plug in Setup Wizard To complete the installation of Opticstar PX 1370 Directshow and Twain Plug in Setup must restart your computer Would you like to restart now Yes restart the computer now O No I will re
20. tallation The camera will now be visible in Windows Device Manager and can be identified as Opticstar PX 137 You can access the Device Manager by clicking the Start button on the Windows desktop and from Settings gt Control Panel select Device Manager Alternatively press Fl on the keyboard while on the Windows desktop to access the Help and Support Center Once there search for Device Manager Z Device Manager a foe File Action View Help TA a e aes ay PEG Computer GP Digital Media Devices coq Disk drives amp Display adapters A DVD CD ROM drives cg IDE ATA ATAPI controllers m Imaging devices Opticstar PX 137C Keyboards Mice and other pointing devices BS Monitors RY Network adapters Ports COM amp LPT m Processors a Sound video and game controllers MM System devices P Universal Senal Bus controllers If the drivers have not been installed properly please refer to the Troubleshooting section in this guide Updated 02 10 2012 10 Opticstar PX 137 Opticstar Ltd 2012 Installing etAMCAP You can test that the camera has been installed successfully e DY running the etAMCAP program remamcap a fou The etAMCAP EXE can be te Bences Options Capture Help found on the accompanying Speen CD inside the etAMCAP folder Copy this to your computer s desktop by dragging it from the CD folder Double click the etAMCAP Icon on the AE
Download Pdf Manuals
Related Search