USER`S MANUAL - Icon Heath & Fitness
Contents
1. B Plug one end of a long 3 5mm to RCA stereo audio cable available at electronics stores into the input jack on the console Plug the other end of the cable into an RCA Y adaptor available at electronics stores Next remove the wire that is currently plugged into the LINE OUT jack on your stereo and plug the wire into the unused side of the Y adaptor Plug the Y adaptor into the LINE OUT jack on your stereo Note While the Y adaptor is plugged into the LINE OUT jack do not plug your headphones into the headphone jack on the console Audio Cable m mnt Wire removed from gt LINE OUT jack HOW TO CONNECT YOUR COMPUTER A Plug one end of a long 3 5mm to 3 5mm stereo audio cable available at electronics stores into the input jack on the console Plug the other end of the cable into the LINE OUT jack on your computer Note While the cable is plugged into the LINE OUT jack do not plug your headphones into the head phone jack on the console LINE OUT Qe Audio Cable HOW TO CONNECT YOUR VCR Note If your VCR has an unused AUDIO OUT jack see instruction A below If the AUDIO OUT jack is being used see instruction B If you have a TV with a built in VCR see instruction B If your VCR is connected to your home stereo see HOW TO CONNECT YOUR HOME STEREO on page 18 A Plug one end of a2. Do not modify the plug provided with the product f it will not fit the outlet have a proper outlet installed by a qualified electrician 10 CONSOLE DIAGRAM CALORIE GOAL PROGRAMMING CALS SET GOAL Vv ENTER WEIGHT Z io gl ne 958 J5 PERSONAL TRAINER PROGRAMS ssa 00 AK JODE 14 16 PRGM QUICK SPEED KM H IMPORTANT Incline must be set at lowest level before folding treadmill into storage position V A INCLINE START Note If there is a sheet of clear plastic on the console peel off the plastic FEATURES OF THE CONSOLE The treadmill console offers an impressive array of features designed to make each workout more effective and enjoyable When the manual mode of the console is selected the speed and incline of the treadmill can be changed with the touch of a button As you exercise the console will display continuous exercise feedback You can even measure your heart rate using the built in handgrip pulse sensor In addition the console features two preset programs Each program automatically controls the speed and in cline of the treadmill as it guides you through an effec tive workout The console also offers two distance pro grams the 5K program counts down from 5 000 me ters as you complete a 5 kilometer run and the 10K program counts down from 10 000 meters And an in novative calorie goal program a
3. insert the key into the console while holding down the Stop button and then release the Stop button When the information mode is selected the following information will be shown An M for metric or an E for English will appear in the lower right corner of the display Press the Speed in crease button to change the unit of measurement if de sired Important If a d appears in the display the console is in the demo mode This mode is intended to be used only when a treadmill is displayed in a store When the console is in the demo mode the power cord can be plugged in the key can be removed from the de 22 console and the display will remain lit the buttons will not operate If a d appears when the information mode is selected press the Speed decrease button so the d disappears The upper left corner of the display will show the total number of hours that the treadmill has been used The lower left corner of the display will show the total number of miles or kilome ters that the walking belt has TIME JD moved To exit the information mode remove the key from the console HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill adjust the incline to the lowest position If this is not done the treadmill may be come permanently damaged Next unplug the power cord CAUTION You must be abl
4. kg to raise lower or move the treadmill When using iFIT com programs an electronic chirping sound will alert you when the speed and or incline of the treadmill is about to change Always listen for the chirp and be prepared for speed and or incline changes In some instances the speed and or incline may change before the personal trainer de scribes the change 21 When using iFIT com programs you can manually override the speed and incline set tings at any time by pressing the speed and incline buttons However when the next chirp is heard the speed and or incline will change to the next settings of the program 22 Remove iFIT com CDs and videos from your CD player or VCR and disconnect your MP3 player when you are not using them 23 When folding or moving the treadmill make sure that the storage latch is fully closed 24 Inspect and properly tighten all parts of the treadmill regularly 25 26 27 Never insert any object into any opening DANGER Always unplug the power cord immediately after use before cleaning the treadmill and before performing the maintenance and adjustment procedures de scribed in this manual Never remove the motor hood unless instructed to do so by an authorised service representative Servicing other than the procedures in this manual should be performed by an authorised ser vice representative only This treadmill is intended for in home use only Do no
5. cone spray or other substances to the walking belt or the walking platform Such substances will deterio rate the walking belt and cause excessive wear HOW TO PLUG IN THE POWER CORD This product must be earthed If it should malfunction or break down earthing provides a path of least resistance for electric cur Socket on Treadmill rent to reduce the risk of electric shock This product is equipped with a power cord having an equipment earthing conductor and an earthing plug Important If the power cord is damaged it must be replaced with a manufacturer recommended power cord See drawing 1 Plug the indicated end of the power cord into the socket on the treadmill See drawing 2 Press the pins on the other end of the power cord into the indicated metal clips in the adaptor Close the adaptor cover over the end of the power cord and tighten the screw in the adaptor Important Make sure that the adaptor cover is secure and that the screw has been tightened before using the power cord See drawing 3 Plug the power cord into an appropriate outlet that is properly installed and earthed in accordance with all local codes and ordinances Important The treadmill is not compatible with GFCl equipped outlets A DANG ER Improper connection of the equipment earthing conductor can result in an in creased risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly earthed
6. long 3 5mm to RCA stereo audio cable available at electronics stores into the input jack on the console Plug the other end of the cable into the AUDIO OUT jack on your VCR AUDIO OUT Audio Cable B Plug one end of a long 3 5mm to RCA stereo audio cable available at electronics stores into the input jack on the console Plug the other end of the cable into an RCA Y adaptor available at electronics stores Next remove the wire that is currently plugged into the AUDIO OUT jack on your VCR and plug the wire into the unused side of the Y adaptor Plug the Y adaptor into the AUDIO OUT jack on your VCR Audio Cable al Wire removed from gt AUDIO OUT jack HOW TO USE AN IFIT COM MP3 CD OR VIDEO PROGRAM To use an iFIT com MP3 CD or video program the treadmill must be connected to your MP3 player CD player or VCR See HOW TO CONNECT THE TREADMILL TO USE IFIT COM PROGRAMS on pages 17 to 19 To download iFIT com MP3 pro grams go to www iFIT com To purchase iFIT com CDs or videocassettes call the toll free telephone number on the front cover of this manual Follow the steps below to use an iFIT com MP3 CD or video program 1 Insert the key into the console See HOW TO TURN ON THE POWER on page 12 Select the iFIT com mode To select the iFIT com mode press th
7. 3 5mm to RCA stereo audio cable available at electronics stores into the input jack on the console Plug the other end of the cable into the AUDIO OUT jack on your stereo Audio Cable B See the drawing above Plug one end of a long 3 5mm to 3 5mm stereo audio cable available at electronics stores into the input jack on the con sole Plug the other end of the cable into the LINE OUT jack on your stereo Note While the cable is plugged into the LINE OUT jack do not plug your headphones into the headphone jack on the con sole C Plug one end of a long 3 5mm to 3 5mm stereo audio cable available at electronics stores into the input jack on the console Plug the other end of the cable into the PHONES jack on your stereo Plug your headphones into the headphone jack on the console Cable A gt 4 5 too Headphones 17 HOW TO CONNECT YOUR HOME STEREO Note If your stereo has an unused LINE OUT jack see instruction A below If the LINE OUT jack is being used see instruction B A Plug one end of a long 3 5mm to RCA stereo audio cable available at electronics stores into the input jack on the console Plug the other end of the cable into the LINE OUT jack on your stereo Note While the cable is plugged into the LINE OUT jack do not plug your headphones into the headphone jack on the console
8. Hood and run the treadmill for a few minutes to check for a cor rect speed reading 25 PROBLEM The walking belt slows when walked on SOLUTION a If an extension cord is needed use only a 3 conductor 1mm 14 gauge cord that is no longer than 1 5 m 5 ft b If the walking belt is overtightened treadmill perfor mance may decrease and the walking belt may be come damaged Remove the key and UNPLUG THE POWER CORD Using the hex key turn both rear roller bolts counterclockwise 1 4 of a turn When the walking belt is properly tightened you should be able to lift each edge of the walking belt 5 to 7 cm 2 to 3 in off the walking platform Be careful to keep the walking belt centered Then plug in the power cord insert the key and run the treadmill for a few minutes Repeat until the walking belt is properly tightened Rear Roller Bolts c If the walking belt still slows when walked on see the front cover of this manual PROBLEM The walking belt is off center or slips when walked on SOLUTION a If the walking belt is off center remove the key and UNPLUG THE POWER CORD If the walking belt has shifted to the left use the hex key to turn the left rear roller bolt clockwise 1 2 of a turn if the walk ing belt has shifted to the right turn the bolt coun terclockwise 1 2 of a turn Be careful not to over tighten the walking belt Then plug in the power cord insert the key and run the
9. REMOVE THIS EXPLODED DRAWING AND PART LIST FROM THE MANUAL Save this EXPLODED DRAWING and PART LIST for future reference Note Specifications are subject to change without notice For information about ordering replacement parts see the back cover of the User s Manual PART LIST Model No PETL37705 0 Key No Qty 0 ONDQUIA WINE N _ Description Hood 3 4 Screw Motor Belt Motor Tension Bolt Right Rear Endcap Motor Star Washer Flywheel Drive Motor Foot Rail Cover Reed Switch Latch Warning Decal Frame Spacer Nut Frame Pivot Bolt Platform Screw Front Handrail Cap Front Roller Pulley Magnet Motor Pivot Bolt Motor Bracket Bolt Handrail Bracket Hood Clip Platform Washer Small Star Washer Foot Rail Screw Bracket Screw Console Fan Motor Tension Nut Latch Housing Latch Catch Left Rear Endcap Platform Screw Rear Motor Plate Left Grip Plate Incline Wire Right Grip Plate Handrail Bolt Fan Housing 1 Tek Screw Ground Wire Rear Roller Star Washer Key No 42 43 44 45 46 47 48 49 50 51 52 53 Qty DARAN AM A 0 put NONNNNN 5 o Mi MI OF WwW SH d UA Description Upright Wire Console Rear Roller Plate Book Holder Extension Leg Nut Console Base 1 2 Screw Wire Clamp Key Clip Incline Motor Rear Roller Washer Incline Motor Bolt Lower Incline Pivot Bolt Motor Fan Motor Controller Wire Round Base Pad 3 4 Tek S
10. To select the calorie goal program press the Program PRGM button repeatedly until a goal of 50 calories and the words SET CALS GOAL appear in the upper left corner of the dis play When the calorie goal program is selected a speed setting will flash in the display The display will also show how long the program will last nr CODE If desired change the calorie goal by press ing the Set Goal in crease or decrease button Each time a button is pressed the calorie goal will change by 50 calories the calorie goal can be from 50 to 450 calories In addition press the Speed increase or decrease button or one of the eight numbered Speed buttons to change the speed setting if de sired SETCALS GOAL Note As you change the calorie goal or the 16 speed setting the program time will automatically be recalculated the higher the calorie goal is or the lower the speed setting is the longer the pro gram will last Press the Start button to start the program A moment after the button is pressed the walking belt will begin to move Hold the handrails and begin walking To change the speed of the walking belt or the in cline of the treadmill at any time during the pro gram press the Speed or Incline buttons Note Each time you change the speed of the walking belt the time remaining in the program will auto matically be recalculated While you exercise the console will show the number of calori
11. ccess basic programs audio programs and video programs directly from the internet Additional options are soon to be available See www iFIT com for details To use programs from our Web site the treadmill must be connected to your home computer See HOW TO CONNECT YOUR COMPUTER on page 18 In addition you must have an internet connection and an internet service provider A list of specific system re quirements is found on our Web site Follow the steps below to use a program from our Web site 1 Insert the key into the console See HOW TO TURN ON THE POWER on page 12 Select the iFIT com mode To select the iFIT com mode press the Program PRGM but ton repeatedly until the iFIT indicator lights Go to your computer and start an internet connection Start your web browser if necessary and go to our Web site at www iFIT com Follow the desired links on our Web site to se lect a program Read and follow the on line instructions for using a program Follow the on line instructions to start the program 21 When you start the program an on screen count down will begin Return to the treadmill and stand on the foot rails Find the clip attached to the key and slide the clip onto the waistband of your clothes 7 When the on screen countdown ends the program will begin and the walking belt will begin to move Hold the handrails step onto the walking belt and begin walking During the
12. crew Controller Lift Frame Extension Leg Pad Warning Decal Extension Leg Wheel Bolt Base Endcap Wheel Platform Nut 8 Cable Tie Uprights Base Grommet Left Handrail Right Handrail Roller Adj Bolt Left Foot Rail Silver Ground Screw iFIT com Wire Belly Pan Screw Incline Stop Bracket Power Cord Assembly Rear Roller Bracket Belly Pan Belt Guide 110 111 tek HH HH H Q 2 f po A A AA dd dl ld CT CT b CORTON CRT OR DO CO SO CORN NA ad a dl CO py a py apo R1205A Description Belt Guide Screw Isolator Fastener Isolator Cushion Frame Releasable Tie Transformer Cable Tie Clamp Front Roller Star Washer Sensor Clip Ground Screw Extension Leg Bolt Hex Key Handrail Star Washer Walking Belt Walking Platform Right Foot Rail U nut Rear Roller Optic Disk Optic Disk Sensor Motor Mount Bracket Latch Pin Assembly Small Nut Small Bolt Controller Screw Outlet Assembly Power Cord Adapter Motor Bushing Filter Electronics Bracket 20 Blue Wire M F 14 Blue Wire 2F 6 Blue Wire 2F 8 Green Wire F R 4 Green Wire F R 12 Red Wire M F 10 Black Wire M F 6 White Wire 2F User s Manual These parts are not illustrated EXPLODED DRAWING Model No PETL37705 0 R1205A OPERATION AND ADJUSTMENT THE PRE LUBRICATED WALKING BELT Your treadmill features a walking belt coated with high performance lubricant IMPORTANT Never apply sili
13. e Program PRGM but ton repeatedly until the iFIT indicator lights Press the Play button on your MP3 player CD player or VCR Note If you are using an iFIT com CD insert the CD into your CD player if you are using an iFIT com videocassette insert the videocassette into your VCR A moment after the Play button is pressed your personal trainer will begin guiding you through your workout Simply follow your personal trainer s instructions Note If the time is flashing in the dis play press the Start button on the console The treadmill will not respond to an MP3 CD or video program while the time is flashing in the display During the program an electronic chirping sound will alert you when the speed and or incline of the treadmill is about to change CAUTION Always listen for the chirp and be prepared for speed and or incline changes In some instances the speed and or incline may change before your personal trainer describes the change 19 If the speed or incline settings are too high or too low you can manually override the settings at any time by pressing the Speed or Incline buttons on the console However when the next chirp is heard the speed and or incline will change to the next settings of the program To stop the walking belt at any time press the Stop button on the console To restart the pro gram press the Start button After a moment the walking belt will begin
14. e to safely lift 20 kg 45 Ibs to raise lower or move the treadmill 1 Hold the metal frame firmly in the location shown by the arrow at the right CAUTION To decrease the possibility of injury do not lift the frame by the plastic foot rails Bend your legs and keep your back straight as you raise the frame make sure to lift with your legs rather than your back Raise the frame about halfway to the vertical position 2 Move your right hand to the position shown and hold the treadmill firmly Using your left hand pull the latch knob to the left and hold it Raise the frame until the hole in the frame is aligned with the latch pin Slowly release the latch knob make sure that the latch pin is fully inserted into the frame To protect the floor or carpet from damage place a mat under the treadmill Keep the treadmill out of direct sun light Do not leave the treadmill in the storage position in temperatures above 30 C 85 F HOW TO MOVE THE TREADMILL Before moving the treadmill convert the treadmill to the storage position as described above Make sure that the latch pin is fully inserted into the frame 1 Hold the upper ends of the handrails and place one foot against one of the wheels 2 Tilt the treadmill back until it rolls freely on the wheels Carefully move the treadmill to the desired location To re duce the risk of injury use extreme caution while mov ing the treadmill Do not mo
15. en insert it Then slide the sleeve back over the connector Sleeve Connector 7 Set the Console Base 47 on the Handrails 71 72 Attach the Console Base with four 3 4 Screws 2 Start all four Screws before tightening any of them do not overtighten the Screws See the inset drawing Make sure that the Upright Wire 42 is routed below the two indicated round posts A Next press the Upright Wire into the slot between the square post B and the Console Base 47 8 10 Cover the Upright Wire 42 with the Right Grip Plate 36 Be careful not to pinch the Upright Wire Tighten two 1 2 Screws 48 and a 3 4 Screw 2 into the Right Grip Plate and the Console Base 47 Attach the Latch Housing 29 to the left Upright 69 with two 3 4 Screws 2 Make sure that the large hole in the Latch Housing is on the side shown Remove the knob from the pin Make sure that the col eee lar and the spring are on the pin as shown Then in sert the pin into the Latch Housing 29 and tighten the knob back onto the pin Large Hole a e Collar ry Make sure that all parts are properly tightened before you use the treadmill Note Extra hardware may be included Keep the included hex keys in a secure place the large hex key is used to adjust the walking belt see page 26 To protect the floor or carpet place a mat under the treadmill
16. er cord has been plugged in make sure that the key is inserted into the console frame near the power cord If the switch protrudes as i L shown the circuit breaker has tripped To reset the Tripped f circuit breaker wait for five minutes and then press the switch back in frame near the power cord Make sure that the switch is in the on position On Position A Check the circuit breaker located on the treadmill frame near the power cord see c above If the circuit breaker has tripped wait for five minutes and then press the switch back in Make sure that the power cord is plugged in If the power cord is plugged in unplug it wait for five minutes and then plug it back in Remove the key from the console Reinsert the key into the console Make sure that the on off switch is in the on position If the treadmill still will not run see the front cover of this manual The displays of the console do not function properly a Remove the key from the console and UNPLUG THE POWER CORD Remove the Screws 77 from the Hood 1 and carefully pivot the Hood off Locate the Reed Switch 10 and the Magnet 18 on the left side of the Pulley 17 Turn the Pulley until the Magnet is aligned with the Reed Switch Make sure that the gap between the Magnet and the Reed Switch is about 3 mm 1 8 in If necessary loosen the Screw 26 move the Reed Switch slightly and then retighten the Screw Reattach the
17. er of meters still to be run When only 20 meters remain the display will flash and a series of tones will sound To stop the program at any time press the Stop button The time will begin to flash in the display To restart the program press the Start button The walking belt will begin to move at 2 km h Adjust the speed of the walking belt as desired by press ing the Speed increase or decrease button or one of the eight numbered Speed buttons When you have completed a 5 kilometer run or a 10 kilometer run your total time will flash in the lower left corner of the display and the words cool and down cool down will flash in the upper left corner of the display If the speed of the walking belt is greater than 8 km h the walking belt will then slow to 8 km h for one minute After one minute the walking belt will slow to 5 km h for 2 minutes The walking belt will then slow to 4 km h for 2 minutes The walking belt will then slow to a stop 4 Follow your progress with the display See step 6 on page 12 5 Measure your heart rate if desired See step 7 on page 13 6 Turn on the fan if desired See step 8 on page 13 When you are finished exercising remove the key from the console HOW TO USE THE CALORIE GOAL PROGRAM 1 Insert the key into the console See HOW TO TURN ON THE POWER on page 12 2 Enter your weight if desired See step 2 on page 12 Select the calorie goal program
18. es still to be burned When you reach your calorie goal the walking belt will slow to a stop Follow your progress with the display See step 6 on page 12 Measure your heart rate if desired See step 7 on page 13 Turn on the fan if desired See step 8 on page 13 When you are finished exercising remove the HOW TO CONNECT THE TREADMILL TO USE IFIT COM PROGRAMS To use iFIT com MP3 or CD programs the treadmill must be connected to your MP3 player CD player portable stereo home stereo or computer See pages 17 and 18 for connecting instructions To use iFIT com programs directly from our Web site the treadmill must be connected to your computer See page 18 for connecting instructions To use iFIT com video pro grams the treadmill must be connected to your VCR See page 19 for connecting instructions HOW TO CONNECT YOUR MP3 PLAYER OR CD PLAYER A Plug one end of the included 3 5mm to 3 5mm stereo audio cable into the input jack on the con sole Plug the other end of the cable into a jack on your MP3 player or CD player Plug your head phones into the headphone jack on the console Audio 5 Cable a Headphones HOW TO CONNECT YOUR PORTABLE STEREO Note If your stereo has an RCA type AUDIO OUT jack see instruction A below If your stereo has a 3 5mm LINE OUT jack see instruction B If your stereo has only a PHONES jack see instruction C A Plug one end of a long
19. ght Upright 69 Feed the Upright Wire into the hole in the bottom of the Right Handrail and out of the large hole in the side Note It may be helpful to use needlenose pliers to pull the Upright Wire out of the hole Press a Handrail Cap 16 onto the lower end of the Right Handrail 72 as shown Set the Right Handrail on the right Upright 69 while sliding the lower end of the Right Handrail onto the right Handrail Bracket 21 Finger tighten a Handrail Bolt 37 with a Handrail Star Washer 95 into the Right Handrail and the right Upright Next attach the lower end of the Right Handrail with a 3 4 Tek Screw 58 and a Small Star Washer 24 Then tighten the Handrail Bolt Attach the Left Handrail 71 in the same way Note There is not an upright wire on the left side 5 Hold the Console Base 47 near the Left Handrail 71 Cut the plastic tie off the ends of the indicated ground wires Attach the ends of the ground wires to the indi cated small hole in the Left Handrail with the Silver Ground Screw 75 6 Touch the Right Handrail 72 to discharge any static Slide the sleeve off the connector on the Upright Wire 42 as shown in the inset drawing Next press the end of the Upright Wire into the socket in the bottom of the Console Base 47 The connector should slide easily into the socket and snap into place If the connector does not slide easily and snap into place turn the connec tor and th
20. ice Department Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds LS118JG UK Tel 08457 089 009 Outside the UK 44 113 387 7133 Fax 44 113 387 7125 To help us assist you please be prepared to provide the following information e the MODEL NUMBER of the product PETL37705 0 e the NAME of the product PROFORM X 820 treadmill e the SERIAL NUMBER of the product see the front cover of this manual e the KEY NUMBER AND DESCRIPTION OF THE PART S see the PART LIST and the EXPLODED DRAWING in the center of this manual Part No 236110 R1205A Printed in USA 2005 ICON IP Inc
21. ickly hold down one of the buttons Note Once you enter your weight it will be saved in memory 3 Select the manual mode Each time the key is inserted the manual mode will be selected If a program has been selected reselect the manual mode by removing the key and then reinserting it Press the Start button to start the walking an belt QS spec When the Start button is pressed the walking belt will begin to move at 2 km h While you exercise change the speed of the walking belt as desired by pressing the Speed increase or decrease button or one of the eight numbered Speed buttons Each time the Speed increase or decrease button is pressed the speed setting will change by 0 1 km h if one of the but tons is held down the speed setting will change in increments of 0 5 km h If one of the numbered Speed buttons is pressed the walking belt will gradually increase in speed until it reaches the se lected speed setting Note After a button is pressed it may take a moment for the walking belt to reach the selected speed setting To stop the walking belt press the Stop button The time will begin to flash in the display To restart the walking belt press the Start button and then adjust the speed setting as described above Change the incline of the treadmill as desired To change the incline of NGINE the treadmill press the Ti Incline increase or de lo crease button Each time a butto
22. ideo pro gram see page 19 To use an iFIT com program di rectly from our Web site see page 21 HOW TO TURN ON THE POWER Plug in the power cord see page 10 Next lo cate the on off switch on On the treadmill frame near Position the power cord Make sure that the switch is in the Or position Next stand on the foot rails of the treadmill Locate the clip attached to the key see the drawing on page 11 and slide the clip securely onto the waistband of your clothes Then insert the key into the console After a moment the display will light Important In an emer gency situation the key can be pulled from the console causing the walking belt to slow to a stop Test the clip by carefully taking a few steps back ward if the key is not pulled from the console ad just the position of the clip Note To prevent damage to the walking platform always wear clean shoes while using the treadmill The first time the treadmill is used observe the alignment of the walking belt and center the walk ing belt if necessary see page 26 HOW TO USE THE MANUAL MODE 1 Insert the key into the console See HOW TO TURN ON THE POWER above Enter your weight if desired While you exercise the console will count the approximate number of calories you burn For the most accurate calorie count enter your weight into the console by repeatedly pressing the Enter Weight increase or decrease button To enter your weight qu
23. l warnings and precautions Use the treadmill only as described Place the treadmill on a level surface with at least 2 5 m 8 ft of clearance behind it and 0 5 m 2 ft on each side Do not place the treadmill on any surface that blocks air open ings To protect the floor or carpet from dam age place a mat under the treadmill Keep the treadmill indoors away from mois ture and dust Do not put the treadmill in a garage or covered patio or near water Do not operate the treadmill where aerosol products are used or where oxygen is being administered Keep children under the age of 12 and pets away from the treadmill at all times The treadmill should be used only by persons weighing 125 kg 275 Ibs or less Never allow more than one person on the treadmill at a time Wear appropriate exercise clothes when using the treadmill Do not wear loose clothes that could become caught in the treadmill Athletic support clothes are recommended for both men and women A ways wear athletic Shoes Never use the treadmill with bare feet wearing only stockings or in sandals When connecting the power cord see page 10 plug the power cord into an earthed cir cuit No other appliance should be on the same circuit When replacing the fuse an ASTA approved BS1362 type should be fitted to the fuse carrier A 13 amp fuse should be used If an extension cord is needed use only a 3 conductor 1mm 14 gauge cord that is no
24. let to fully insert the Extension Leg Next hold two Extension Leg Nuts 46 in the bottom of the Extension Leg and insert two Extension Leg Bolts 93 into the top of the Extension Leg Firmly tighten the Extension Leg Bolts into the Extension Leg Nuts Attach two Base Pads 57 to the base of the Uprights 69 with two 1 Tek Screws 39 NIN INI 2 Attach a Wheel 66 to the base of the Uprights 69 with a Wheel Bolt 64 and a Nut 13 as shown Do not overtighten the Wheel Bolt the Wheel should turn freely With the help of a second person carefully tip the tread mill onto its other side See assembly step 1 and attach the other Extension Leg 63 and the remaining two Base Pads 57 Then attach the other Wheel 66 as described above WII With the help of a second person carefully tip the tread mill down so the Uprights 69 are in a vertical position 3 Insert the tab on one of the Handrail Brackets 21 into the slot in the right Upright 69 Attach the Handrail Bracket with a 3 4 Screw 2 and a Small Star Washer 24 Attach the other Handrail Bracket to the left Upright not shown in the same way 4 If there is a board between the Uprights 69 remove the board and the two bolts Discard the board and the bolts Identify the Right Handrail 72 which has a large hole in the left side Cut the plastic tie securing the Upright Wire 42 to the ri
25. llows you to set a calo rie burning goal for each workout The console also features iFIT com interactive technol ogy Having iFIT com technology is like having a per sonal trainer in your home Using a stereo audio cable 11 A WARNING To reduce risk of serious injury stand on foot rails before starting treadmill read and understand the user s manual all instructions and the warnings before use eep children away you can connect the treadmill to your portable stereo home stereo computer or VCR and play special iFIT com MP3 CD and video programs iFIT com MP3 programs CDs and videocassettes are available sepa rately iFIT com programs automatically control the speed and incline of the treadmill as a personal trainer guides you through every step of your workout high energy music provides added motivation To down load iFIT com MP3 programs go to www iFIT com To purchase iFIT com CDs or videocassettes call the toll free telephone number on the front cover of this manual With the treadmill connected to your computer you can also go to www iFIT com and access iFIT com programs directly from our Web site See www iFIT com for more information To use the manual mode of the console follow the steps beginning on page 12 To use a preset program see page 14 To use a distance program see page 15 To use the calorie goal program see page 16 To use an FIT com MP3 CD or v
26. longer than 1 5 m 5 ft 12 13 14 15 16 17 18 19 20 Keep the power cord away from heated sur faces Never move the walking belt while the power is turned off Do not operate the treadmill if the power cord or plug is damaged or if the treadmill is not working properly See TROU BLESHOOTING on page 23 if the treadmill is not working properly Read understand and test the emergency stop procedure before using the treadmill see OPERATION AND ADJUSTMENT on page 10 Never start the treadmill while you are stand ing on the walking belt Always hold the handrails while using the treadmill The treadmill is capable of high speeds Adjust the speed in small increments to avoid sudden jumps in speed The pulse sensor is not a medical device Various factors including the user s move ment may affect the accuracy of heart rate readings The pulse sensor is intended only as an exercise aid in determining heart rate trends in general Never leave the treadmill unattended while it is running Always remove the key unplug the power cord and move the on off switch to the off position when the treadmill is not in use See the drawing on page 5 for the loca tion of the on off switch Do not attempt to raise lower or move the treadmill until it is properly assembled See ASSEMBLY on page 6 and HOW TO FOLD AND MOVE THE TREADMILL on page 21 You must be able to safely lift 45 pounds 20
27. lungs to oxygenate the blood For aerobic exercise adjust the speed and incline of the treadmill until your heart rate is near the highest number in your training zone WORKOUT GUIDELINES Each workout should include the following three parts A Warm up Start each workout with 5 to 10 minutes of stretching and light exercise A proper warm up in creases your body temperature heart rate and circula tion in preparation for exercise Training Zone Exercise After warming up increase the intensity of your exercise until your pulse is in your training zone for 20 to 60 minutes During the first few weeks of your exercise program do not keep your pulse in your training zone for longer than 20 minutes Breathe regularly and deeply as you exercise never hold your breath A Cool down Finish each workout with 5 to 10 min utes of stretching to cool down This will increase the flexibility of your muscles and will help prevent post exercise problems EXERCISE FREQUENCY To maintain or improve your condition complete three workouts each week with at least one day of rest be tween workouts After a few months you may com plete up to five workouts each week if desired The key to success is to make exercise a regular and enjoyable part of your everyday life 27 ORDERING REPLACEMENT PARTS To order replacement parts contact the ICON Health amp Fitness Ltd office or write ICON Health amp Fitness Ltd Customer Serv
28. n is pressed the incline will change by 0 5 Note After a button is pressed it may take a moment for the treadmill to reach the selected incline set ting Follow your progress with the display When the manual mode a distance program the calorie goal program or the iFIT com mode is selected a track represent ing 400 meters 1 4 mile will appear in the upper right corner of the display As you walk or run on the treadmill the indicators around the track will appear in succession until the en tire track appears The track will then disap pear and the indicators will again begin to ap pear in succession The upper left corner of the display will show the approximate number of calories you have burned dur ing your workout Note When the calorie goal program is selected the display will show the number of calories still to be burned BO CALS The lower left corner of the display will show the elapsed time and the distance that you have walked or run during your work out The lower left corner of the display will also show the incline level of the treadmill for a few seconds each time the incline setting changes Note When a preset program or the calorie goal program is selected the lower left corner of the display will show the time remaining in the pro gram instead of the elapsed time The lower right corner of the dis play will show the speed of the walk ing belt When y
29. ng KEEP HANDS AND FEET AWAY FROM THIS AREA WHILE THE TREADMILL IS IN OPERATION Always wear athletic shoes while operating treadmill BEFORE YOU BEGIN Thank you for selecting the new PROFORM X 820 treadmill The X 820 treadmill offers an array of fea tures designed to make your workouts at home more enjoyable and effective And when you re not exercis ing the unique X 820 treadmill can be folded up re quiring less than half the floor space of other treadmills For your benefit read this manual carefully before you use the treadmill If you have questions after Accessory Tray Handrail Storage Latch Walking Belt Foot Rail BACK Rear Roller Adjustment Bolts reading this manual please see the front cover of this manual To help us assist you note the product model number and serial number before calling The model number of the treadmill is PETL37705 0 The serial number can be found on a decal attached to the tread mill see the front cover of this manual for the location Before reading further please review the drawing below and familiarise yourself with the labelled parts Console Key Clip Upright On Off Switch Circuit Breaker Cushioned Walking Platform for maximum exercise comfort RIGHT SIDE ASSEMBLY Assembly requires two persons Set the treadmill in a cleared area and remove all packing materials do not dispose of the
30. on page 13 A Select a distance program HOW TO USE A DISTANCE PROGRAM 1 Insert the key into the console See HOW TO TURN ON THE POWER on page 12 To select a distance program press the Program PRGM but ton repeatedly until P 3 or P 4 appears in the display When a distance program is se lected the maximum speed setting of the program will flash in the display for a few seconds A dis tance goal of 5 000 meters or 10 000 meters will then appear in the display Press the Start button to start the program A moment after the button is pressed the walking belt will begin to move at 4 km h Hold the handrails and begin walking Near the end of the second minute of the pro gram the speed setting will flash in the display and a series of tones will sound The speed of the walking belt will then increase to 5 km h Near the end of the fourth minute of the program the speed setting will flash in the display and a se ries of tones will sound The speed of the walking belt will then increase to 8 km h Near the end of the fifth minute of the program the speed setting will flash in the display and a se ries of tones will sound The speed of the walking belt will then increase to 10 km h Note To change the speed of the walking belt or the incline of the treadmill at any time during the 15 program press the Speed or Incline buttons The upper left corner of the display will show the numb
31. ond time To turn off the fan press the button a third time Note If the fan is on when the walking belt is stopped the fan will turn off au tomatically after a few minutes When you are finished exercising remove the key Step onto the foot rails press the Stop button and adjust the incline of the treadmill to the lowest setting The incline must be at the lowest setting when the treadmill is folded to the storage posi tion or the treadmill will become damaged Next remove the key from the console and put it in a se cure place Note If the display remains lit after the key is removed the console is in the demo mode See page 22 and turn off the demo mode When you are finished using the treadmill HOW TO USE A PRESET PROGRAM 1 Insert the key into the console See HOW TO TURN ON THE POWER on page 12 Select a preset pro gram To select a preset pro gram press the Program PRGM but ton repeatedly until P 1 or P 2 appears in the display When a preset program is selected the maximum incline setting of the program and the maximum speed setting of the program will flash in the display for a few seconds The display will then show how long the program will last and the approximate number of calories you will burn dur ing the program A profile of the speed settings of the program will scroll across the matrix in the upper right corner of the display Press the Start button to star
32. ou use the handgrip pulse sensor the lower right corner of the dis play will also show your heart rate Note When a distance program is selected the lower right corner of the display will also show the approximate number of calories you have burned mi LS SPEED To reset the display press the Stop button re move the key and then reinsert the key Note The console can display speed distance and weight using either metric kilometers and kilo grams or standard miles and pounds To find which system of measurement is selected or to select a different system see THE INFORMA TION MODE DEMO MODE on page 22 Note For simplicity all instructions in this section refer to kilometers and kilograms 13 Note Before using the handgrip pulse sensor remove the sheets of clear plastic from the metal contacts on the handgrip pulse sensor In addition make sure that your hands are clean To measure your heart rate stand on the foot rails and hold the metal contacts on the handrail avoid moving your hands When your pulse is detected the heart symbol in the display will flash each time your heart beats one or two dashes will appear and then your heart rate will be shown For the most accurate heart rate reading continue to hold the contacts for about 15 seconds Turn on the fan if desired To turn on the fan at low speed press the Fan button To turn on the fan at high speed press the button a sec
33. packing materials until assembly is completed Note The underside of the treadmill walking belt is coated with high performance lubricant During shipping a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton This is a normal condition and does not affect treadmill perfor mance If there is lubricant on top of the walking belt simply wipe off the lubricant with a soft cloth and a mild non abrasive cleaner Assembly requires the included hex keys and your own phillips screwdriver gt rubber mallet and adjustable spanner A For help identifying assembly hardware see the drawings below If a part is not in the parts bag first check to see if it has been preassembled um GD HO 1 2 Screw 48 3 Extension Leg Small Star Handrail Star Nut 13 2 Nut 46 4 Washer 24 4 Washer 95 2 wp p cosi a Silver Ground 3 4 Tek Screw 1 Tek Screw 39 4 Extension Leg Bolt 93 4 Screw 75 1 3 4 Screw 2 9 Wheel Bolt 64 2 Handrail Bolt 37 2 1 Make sure that the power cord is unplugged With the help of a second person carefully tip the treadmill onto its left side as shown Partially fold the Frame 86 so the treadmill is more stable Do not fully fold the treadmill until it is completely assembled Insert an Extension Leg 63 into the base of the Uprights 69 with the Extension Leg Pad 61 oriented as shown lf necessary use a rubber mal
34. program an electronic chirping sound will alert you when the speed and or incline of the treadmill is about to change CAUTION Always listen for the chirp and be prepared for speed and or incline changes If the speed or incline settings are too high or too low you can manually override the settings at any time by pressing the Speed or Incline buttons on the console However when the next chirp is heard the speed and or incline will change to the next settings for the program To stop the walking belt at any time press the Stop button on the console To restart the pro gram press the Start button After a moment the walking belt will begin to move at 2 km h When the next chirp is heard the speed and incline will change to the next settings of the program When the program is completed the walking belt will stop Note To use another program press the Stop button and go to step 5 Note If the speed and or incline of the treadmill does not change when a chirp is heard make sure that the iFIT indicator is lit and that the time is not flashing in the display In addition make sure that the audio cable is properly con nected E Follow your progress with the display See step 6 on page 12 THE INFORMATION MODE DEMO MODE The console features an information mode that keeps track of treadmill usage information and allows you to select a system of measurement To select the information mode
35. rrrO FOre 2K TITO Model No PETL37705 0 Serial No USER S MANUAL QUESTIONS As a manufacturer we are com mitted to providing complete customer satisfaction If you have questions or if there are missing or damaged parts please call 08457 089 009 Or write ICON Health amp Fitness Ltd Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds LS11 8JG UK email csuk iconeurope com 44 CAUTION Read all precautions and instruc tions in this manual before using this equipment Save this manual for future reference QQ SS www iconeurope com Visit our website at rert0 FONM aL SZC TABLE OF CONTENTS IMPORTANT PRECAUTIONS i nr 3 BEFORE VOUBEGIN vasos acota oi ATI 5 PS A 6 OPERATION AND ADJUSTMENT L i 10 HOW TO FOLD AND MOVE THE TREADMILL 0 i 23 TROUBLESHOOTING ri ide 25 CONDITIONING GUIDELINES ear 27 ORDERING REPLACEMENT PARTS i i Back Cover Note An EXPLODED DRAWING and a PART LIST are attached in the center of this manual PROFORM is a registered trademark of ICON IP Inc 2 IMPORTANT PRECAUTIONS A WARN ING To reduce the risk of burns fire electric shock or injury to persons read the following important precautions and information before operating the treadmill Ue 10 11 It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of al
36. t the program A moment after the button is pressed the tread mill will automatically adjust to the first speed and incline settings of the program Hold the handrails and begin walking Each program is divided into 30 one minute peri ods One speed setting and one incline setting are programmed for each period Note The same speed setting and or incline setting may be pro grammed for two or more consecutive peri ods Current Period The speed setting for the first period will be shown in the flashing Current Period column of the matrix The incline settings are not shown in the matrix The speed settings for the next four periods will be shown in the columns to the right When only three seconds remain in the first period of the program both the Current Period column and the column to the right will flash and a series of tones will sound If the speed and or incline of the treadmill is about to change the speed setting and or the incline setting will flash in the display to alert you 7 When the first period is completed a speed set tings will move one column to the left The speed setting for the second period will then be shown in the flashing Current Period column and the tread mill will automatically adjust to the speed and in cline settings for the second period Note If all five of the indicators in the Current Period column are lit he speed settings may move downwardso that only the highest indica
37. t use this treadmill in a commer cial rental or institutional setting AWARN l NG Before beginning this or any exercise program consult your physician This is especially important for persons over the age of 35 or persons with pre existing health problems Read all instructions before using ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product SAVE THESE INSTRUCTIONS The decals shown here have been placed on the treadmill If a decal is missing or if it is not legible call the toll free telephone number on the front cover of this manual and order a free replacement decal Apply the decal in the location shown Protect yourself and others from risk of serious injury Read the user s manual and Y Stand only on the side rails when starting or stopping treadmill Change speed in small increments Hold handrails to prevent falling and always wear the safety clip while operating treadmill Stop if you feel faint dizzy or short of breath Fully engage storage latch before tread mill is moved or stored Reduce incline to its lowest level before folding treadmill into storage position Never allow children on or around treadmill Remove key when not in use Keep clothing fingers and hair away from moving belt Never try to adjust or fix the belt while it is movi
38. to move at 2 km h When the next chirp is heard the speed and or in cline will change to the next settings of the program When the program is completed the walking belt will stop Note To use another MP3 CD or video program press the Stop button or remove the key and go to step 1 on page 19 Note If the speed and or incline of the treadmill does not change when a chirp is heard e Make sure that the iFIT indicator is lit and that the time is not flashing in the display If the time is flashing press the Start button on the console e Adjust the volume of your MP3 player CD player or VCR If the volume is too high or too low the console may not detect the program signals 20 e Make sure that the audio cable is properly connected e If you are using a portable CD player and the CD skips set the CD player on the floor or an other flat surface instead of on the console DI Follow your progress with the display See step 6 on page 12 E Measure your heart rate if desired See step 7 on page 13 G Turn on the fan if desired 7 See step 8 on page 13 When you are finished exercising remove the key from the console See step 9 on page 13 CAUTION Always remove iFIT com CDs and videocassettes from your CD player and VCR and disconnect your MP3 player when you are not using them HOW TO USE AN IFIT COM PROGRAM DIRECTLY FROM OUR WEB SITE Our Web site at www iFIT com allows you to a
39. tors appear in the matrix The program will continue in this way until the speed setting for the last period is shown in the Current Period column and the last period ends The walking belt will then slow to a stop If the speed or incline setting for the current period is too high or too low you can manually override the setting by pressing the Speed or Incline buttons Every few times a Speed button is pressed an additional indicator will appear or dis appear in the Current Period column if any of the columns to the right of the Current Period column have the same number of lit indicators as the Current Period column an additional indicator may appear or disappear in those columns as well Important When the current period of the program ends the treadmill will automatically adjust to the speed and incline settings for the next period To stop the program at any time press the Stop button The time will begin to flash in the display To restart the program press the Start button The walking belt will begin to move at 2 km h When the next period of the program begins the treadmill will automatically adjust to the speed and incline settings for the next period Follow your progress with the display See step 6 on page 12 Measure your heart rate if desired See step 7 on page 13 Turn on the fan if desired See step 8 on page 13 When you are finished exercising remove the key from the console See step 9
40. treadmill for a few minutes Repeat until the walking belt is centered b If the walking belt slips when walked on remove the key and UNPLUG THE POWER CORD Using the hex key turn both rear roller bolts clockwise 1 4 of a turn When the walking belt is correctly tightened you should be able to lift each edge of the walking belt 5 to 7 cm 2 to 3 in off the walking platform Be careful to keep the walking belt centered Then plug in the power cord insert the key and carefully walk on the treadmill for a few minutes Repeat until the walking belt is properly tightened 26 CONDITIONING GUIDELINES AWARNING Before beginning this or any exercise program consult your physi cian This is especially important for individu als over the age of 35 or individuals with pre existing health problems The pulse sensor is not a medical device Various factors including the user s move ment may affect the accuracy of heart rate readings The pulse sensor is intended only as an exercise aid in determining heart rate trends in general The following guidelines will help you to plan your ex ercise program For more detailed exercise informa tion obtain a reputable book or consult your physician EXERCISE INTENSITY Whether your goal is to burn fat or to strengthen your cardiovascular system the key to achieving the desired results is to exercise with the proper intensity The proper intensity level can be found by using yo
41. ur heart rate as a guide The chart below shows recom mended heart rates for fat burning and aerobic exercise 130 118 125 115 110 103 105 95 90 60 70 80 To find the proper heart rate for you first find your age near the bottom of the chart ages are rounded off to the nearest ten years Next find the three numbers above your age The three numbers define your train ing zone The lower two numbers are recommended heart rates for fat burning and the higher number is the recommended heart rate for aerobic exercise Fat Burning To burn fat effectively you must exercise at a relatively low intensity level for a sustained period of time During the first few minutes of exercise your body uses easily accessible carbohydrate calories for en ergy Only after the first few minutes does your begin to use stored a7 calories for energy If your goal is to burn fat adjust the speed and incline of the treadmill until your heart rate is near the lowest number in your training zone For maximum fat burning adjust the speed and incline of the treadmill until your heart rate is near the middle number in your training zone Aerobic Exercise If your goal is to strengthen your cardiovascular sys tem your exercise must be aerobic Aerobic exercise is activity that requires large amounts of oxygen for prolonged periods of time This increases the demand on the heart to pump blood to the muscles and on the
42. ve the treadmill over an un even surface 3 Place one foot against one of the wheels and carefully lower the treadmill until it is resting in the storage position 23 HOW TO LOWER THE TREADMILL FOR USE 1 Hold the treadmill with your right hand as shown Pull the latch knob to the left and hold it Pivot the frame down until it is past the latch pin 2 Hold the metal frame firmly with both hands and lower the frame to the floor CAUTION To decrease the possibility of injury do not lower the frame by gripping only the plastic foot rails Do not drop the frame to the floor Make sure to bend your legs and keep your back straight 24 TROUBLESHOOTING Most treadmill problems can be solved by following the steps below Find the symptom that applies and follow the steps listed If further assistance is needed see the front cover of this manual PROBLEM The power does not turn on SOLUTION PROBLEM SOLUTION PROBLEM SOLUTION a The power turns off during use a d e Check the circuit breaker located on the treadmill Check the on off switch located on the treadmill Make sure that the power cord is plugged into a properly earthed outlet See page 10 If an ex tension cord is needed use only a 3 conductor 1 mm 14 gauge cord that is no longer than 1 5 m 5 ft Important The treadmill is not compatible with GFCI equipped outlets After the pow
Download Pdf Manuals
Related Search