User-Manual - Newegg.com
Contents
1. The manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output signal is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device This product uses patented technology to protect the carrier network FCC Requirement This is a CONSUMER device BEFORE USE you MUST REGISTER THIS DEVICE with your wireless provider and have your provider s consent Most wireless providers consent to the use of signal boosters AT amp T Sprint T Mobile Verizon and 90 additional carriers have already given consent for all consumers to use this device Some providers may not consent to the use of this device on their network If you are unsure contact your provider You MUST operate this device with approved antennas and cables as specified by the manufacturer Antennas MUST be installed at least 20 cm 8 inches from any person You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider WARNING E911 location information may not be provided or may be inaccurate for calls served by using this device FCC contact information www fcc gov signal boosters registration FCC Information FCC ID S0O4ZB570 PCS CEL Warning Ch2. ANTENNA to pick up the Di E Pi strongest signal from your wireless carrier optimal system 3 Move the EXTERNAL ANTENNA as far away from the gain Three INDOOR ANTENNA as possible with at least 15 ft of flashes or less vertical separation height difference indicates the 4 Plug the BASE UNIT power supply back in 5 Wait 30 secs for the BASE UNIT to power cycle on Flashing GREEN Solution 1 system will still operate properly After Initial Power Up A p Mode GREEN ready GREEN in use SOLID EXTERNAL Unplug the BASE UNIT power supply ORANGE ANTENNA Move the EXTERNAL ANTENNA as far away from the OTENNA INDOOR ANTENNA as possible with at least 15 ft of are too close vertical separation height difference together Plug the BASE UNIT power supply back in Wait 30 secs for the BASE UNIT to power cycle on Unplug the BASE UNIT power supply Relocate the EXTERNAL ANTENNA to another spot If you have a directional antenna re aim it to reduce carrier signal strength 4 Plug the BASE UNIT power supply back in 5 Wait 30 secs for the BASE UNIT to power cycle on Refer to Solution 2 Solution 2 Solution 3 SOLID Signal from the RED carriers cell tower is too strong for the BASE UNIT to operate properly Flashing Excessive RED electronic noise in the system the BASE UNIT will not operate DMAN 0061 Rev 2714 zBoost SOHO ZB545 Technical Specifications a CS C
3. smt gst nsf en sf08942e html Cet appareillage num rique de la classe B r pond a toutes les exigences de l interference canadienne causant des r glements d quipement L op ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dispositif doit accepter n importe quelle interference re ue y compris l interf rence qui peut causer l op ration peu d sir e Le fabricant nominale de la puissance de sortie de ce mat riel est simple transporteur Pour les situations lorsque plusieurs signaux porteurs sont pr sents l valuation devrait tre r duite de 3 5 dB en particulier lorsque le signal de sortie est re emise et peut provoquer des interf rences adjacentes a la bande utilisateurs Ce pouvoir est de la reduction par le biais de la sortie d alimentation ou la r duction de gain et non par un att nuateur a la sortie du dispositif Warranty information LIMITED 1 YEAR MANUFACTURER WARRANTY WARRANTY REGISTRATION AT WWW ZBOOST COM zBoost warrants every zBoost product to be free from defects in material and workmanship under normal use for the warranty period of 1 year Who Is Covered You must have proof of purchase to receive warranty service A sales receipt or other documentation showing the product purchased and the purchase date is considered proof of purchase This limited warranty extends only to the original consumer purchaser or any person receiving the pro
4. anges or modifications to this device not expressly approved by zBoost could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter In accordance with FCC requirements of human exposure to radiofrequen
5. cy fields the radiating element antenna shall be installed such that a minimum separation distance of 20cm 8in is maintained from all persons Industry Canada Regulations Canada IC 5544A ZB570PCSCEL This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The term IC before the radio certification number only signifies that Industry Canada technical specifications were met RF Exposure The manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device Please note This unit has been approved for use in Canada under RSS 131 however consent for the use of this device to improve cellular or PCS coverage must be obtained through your cellular or PCS provider prior to placing the unit in operation Please refer to the Industry Canada document CPC 2 1 05 Section 6 1 available or viewable at http Awww ic gc ca epic site
6. duct as a gift from the original consumer purchaser and to no other purchaser or transferee This warranty does NOT extend to commercial users What is Covered Warranty coverage begins the day you purchase the product For one year from the original date the zBoost Cell Phone Signal Booster will be repaired or replaced with a new repaired refurbished or comparable product whichever is deemed necessary by zBoost if it becomes defective or inoperative The exchange will be made without charge to you for parts and labor You will be responsible for the cost of shipping to the location designated by zBoost If zZBoost cannot reasonably repair or replace the unit then zBoost may at its sole discretion refund the price you paid for the product or the price of the unit All products including replacement products are covered only for the original warranty period When the warranty on the original product expires the warranty on the replacement product also expires What is Excluded Your warranty does NOT cover e Labor charges for set up of the unit e Product replacement because of misuse accident lightning damage unauthorized repair or other cause not within the control of zBoost e Incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you e Any modifications or other changes to the product including but not li
7. e antenna Choose one of the following options for placement of the External Antenna keeping in mind that if your best signal is one bar your coverage will be limited to one small room To maximize signal coverage place the External Antenna where you find the strongest signal up high or outside and at least 3 feet above any metal IMPORTANT Incorrectly mounting the External Antenna to the mounting bracket see figure A will decrease performance Ensure that the External Antenna is properly positioned in the mounting bracket as pictured in figure B To mount antenna to a non metal pole Attach bottom of antenna to pole bracket Antenna at highest elevation 15feetabove s Base Unit Adequate Performance Place External Antenna outside of window Best Performance Recommended Place External Antenna on roof or in attic SETUP OVERVIEW Download the ZB545 Manual at www zBoost com as pictured Use U Bolt to secure bracket to pole and fasten To mount antenna to a flat surface Attach bottom of antenna to pole bracket as pictured Secure bracket to desired surface using provided screws Use of the Saddle and U Bolt are not necessary for this option STEP 2 Place the zBoost Base Unit where you want to create a Cell Zone Connect the Indoor Antenna to the Base Unit and place it where you need signal For the widest possible signal area position the Base Unit near the middle of a room You may also mount it on a
8. e calls If the signal strength has improved your zBoost is working Remember coverage varies based on outdoor signal level building construction and antenna placement Coverage in adjoining rooms next to above or below will be reduced by walls and ceiling floors Upon initial power up the LED will cycle RED GREEN and ORANGE for 30 seconds After 30 seconds a series of GREEN flashes will indicate the quality of your setup 1s v7 1 ff 2 eee m Px A r l l Pole Bracket J Ven Saddle a l f Power Supply i uBot A TUN Z zBoost Base Unit Figure B ZBoost SOHO ZB545 Following this a solid GREEN light indicates normal conditions If it is not solid GREEN follow the instructions in the Base Unit LED Indicators section Adjustments may be needed to optimize performance If you find the increased signal coverage is acceptable however no additional adjustments are needed See the LED chart for more information Should you desire to improve coverage e Relocate the External Antenna to capture a better signal higher is better e Increase the distance between the Indoor Antenna and the External Antenna e Purchase an upgrade antenna at www zBoost com Base Unit LED Indicators During Initial Power Up Cycle RED GREEN ORANGE System is powering up Please allow up to 30 seconds BASE UNIT will 1 Unplug the BASE UNIT power supply flash GREEN 2 Relocate the EXTERNAL
9. l number found on the product Model Serial Purchase Date Customer Support The complete zBoost SOHO ZB545 Manual and additional product information is available at www zBoost com For questions or assistance contact zBoost Customer Care at 1 800 871 1612 or email Support zBoost com
10. mited to software or hardware modifications in any way other than as expressly authorized by zBoost will void this limited warranty e Product that has been modified or adapted to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications Make sure you keep Please keep your sales receipt or other document showing proof of purchase Attach it to this Setup Overview and keep both nearby Also keep the original box and packing material in case you need to return your product Before requesting repair service Please see the BASE UNIT LED INDICATORS section listed in this overview for troubleshooting To get warranty service Warranty service will be provided by zBoost If you need service for your unit contact us at 1 800 871 1612 or support zBoost com A representative will go through a diagnostic checklist with you If the product needs to be returned for service or exchanged you will receive a return merchandise authorization RMA number The representative will give you complete shipping details Please do not return products to zBoost without an RMA To get out of warranty service To obtain out of warranty service contact zBoost at 1 800 871 1612 or support zBoost com for information on the possibility of any costs for repair or replacement of out of warranty products Reminder Record the model and seria
11. n interior wall by first removing the bracket screwing the bracket to a wall screws not included then snapping the Base Unit back in place keeping the Indoor Antenna vertical The Base Unit uses an omni directional Indoor Antenna that delivers signal in a circular pattern around the antenna The zBoost SOHO requires at least 15 feet of vertical separation between the Base Unit and the External Antenna Generally increasing this distance up to 40 feet will increase the performance and decreasing the distance will limit the performance Keep the Base Unit off the floor and at least 2 feet away from other cords metal objects or other wireless devices such as wireless routers or wireless access points The zBoost SOHO performs best when there are no obstructions between the zBoost Base Unit and your mobile device STEP 3 Run the provided coaxial cable between the Base Unit and External Antenna Connect one end of the cable to the External Antenna and the remaining end to the Base Unit Should additional cable length be needed 15 ft extensions Part YX030 15w are available at www zBoost com Note Cable runs longer than 60 ft are not recommended for RG 6 unless upgraded to RG 11 RG 11 can be run up to 120 ft STEP 4 Connect the zBoost Base Unit to the provided power supply and plug into a power outlet When your zBoost system is in place and fully connected walk throughout your home or office and verify that you are able to reliably plac
12. zBoost extending cell zones Package Contents zBoost Base Unit SETUP OVERVIEW Setup Overview Indoor Antenna Coax Cable RG 6 50 ft External Antenna External Antenna Power Supply Mounting Hardware comes in 2 pieces Setting Up Your zBoost Signal Booster Designed for single family homes zBoost cell phone signal boosters extend a Cell Zone for multiple devices such as iPhone Android and Samsung operating on 800 and 1900 MHz frequency bands zBoost boosts signal coverage up to 2 500 sq ft perfect for your home or office Boost voice and data transmission and increase call clarity in 4 easy steps STEP 1 Mount the External Antenna Choose a location for the antenna using your cell phone to determine the area of strongest signal The coverage your zBoost booster provides is largely determined by the strength of signal received by the External Antenna Before installing please note the following important factors in determining your zBoost performance e Atleast 15 vertical feet is needed between the External Antenna receives the outside signal and the Indoor Antenna rebroadcasts the signal indoors Separation less than 15 vertical feet will result in decreased performance e Keep the External Antenna at least 3 feet above any metal such as wiring A C ducts truss plates etc When attaching the cable to the antenna run the cable straight down from the antenna Avoid draping the coax near th
Download Pdf Manuals
Related Search