Data sheet DB EN AXL BK PN (-ME)
Contents
1. 13 Dynamic configuration on the Axio bus local bus You can use the Dynamic configuration function with this bus coupler Dynamic configuration is the specification and configuration of a maximum configuration Any subgroup of this maximum configuration can be operated 14 When PROFINET communication breaks down or an error occurs in the Axio bus all outputs of the Axioline station are set to the parameterized substitute values The Axio bus con tinues to run with these values Substitute value behavior 15 Startup Default upon delivery default settings By default upon delivery the following functions and features are available PROFINET IO name No name assigned IP parameters 0 0 0 0 Module designation AXL BK PN ME Vendor ID OOBOnex Device ID 1000hex PROFINET controllers from Phoenix Contact support the Operation with differences in con figuration yes no function from version 3 70 or later i If you are using an earlier firmware version set the Operation with configuration differences function to yes in the context menu of the bus coupler under the PROFINET settings tab When configuration differences are detected this prevents that data from the application is briefly being output at the outputs of the config ured modules before operation is terminated completely Firmware started Once you have supplied the bus coupler with power or pressed the reset button the fi2. 4 AXL BK PN ME Interface Service USB adapter Number Connection method System limits of the bus coupler Amount of process data Number of supported devices PROFINET IO Device function Conformance class Update rate Number of supported application relationships AR Protocols supported Protocols supported Supported MIBs Supported standard MIBs Supported private MIBs Supply of the bus coupler Supply of communications power UL Maximum permissible voltage range Current supply at Upys Current consumption from U Power consumption at UL 1 IFS USB PROG ADAPTER 1485 Byte for each data direction max 63 per station PROFINET IO device B 250 us 2 PROFINET IO FTP TFTP LLDP SNMP MRP DDI BootP RFC 1213 MIB Il Phoenix Contact MIB 24V DC 19 2 V DC 30 V DC including all tolerances including ripple 2A Typ 86 mA without I Os and U 24 V max 600 mA with 2 A at Ugus for the I Os and U 24 V max 750 mA with 2 A load at Ugus for the I Os and U 19 V Typ 2 W without I Os max 14 4 W with 2 A load at Ugus for the I Os Error messages to the higher level control or computer system None Mechanical tests Vibration resistance in acc with IEC 60068 2 6 Shock test in acc with IEC 60068 2 27 Bump endurance test according to EN 60068 2 29 Conformance with EMC Directive 2004 108 EC Noise immunity test in accordance with EN 61000 6 2 Electrostatic discharge ESD
3. 2 3 Ord ring data sates esas ahs ae hr t AE eE E a E a a E a r a aata 3 4 Fechmcal datas osann e a tact 8 sale ae reas a a e e E 4 5 Internal circuit diagram eeeeeeeeeeeeeeeeeeiettesestiiirttsssstttt ttnt attt caneuiee sees apianadsaeeaseaceecavide eee ates 6 6 Connecting PROFINET and supply s sssssssssssenesssreessnrrsssrrrsstrrnnetrnnntttnnnssttnnsstennnetnnnnntnnn nenene 7 6 1 Conmecing PROFINET oroarea a T E E S 7 6 2 Connecting the supply voltage terminal point aSsigNnMent s sssssssssssssrsrsrsnerrrrrnnrrnnnnrnnnrnrnrnenenennn 7 7 Connection example s snot a pa ae EE EE A EATE EERE E aE EEEE ERa Ean 7 8 Local status and diagnostic indicators cece eee eeennnne ee eeeeeeeeeaaeeeeeeeeeeeaaaeeeeeeeeeeeneenaaeees 8 9 Diagnostic Indicators for PROFINET cc gerse eeiaereccteatevaireastiea sty eas iateune tour nee dnateteatecd ates 9 HO VDIAGMOSIC SIAN Sas encceccnes monte team tere ann ea eer asad erat teat E 9 11 Device TreplaCement c icee niae E EKA aE ENEKE a AKEE obteeaeadie Gale 9 12 Phoenix Redundancy Layer PRL sssessssnnnsosenneerenereeenrrsorrrnnrerrnnrtnnnnesrernseerrnnrenen reser eneee 10 13 Dynamic configuration on the Axio bus local DUS sseesssssessennrnesrnneeenresserrrserenrnnrnnnneenne 10 14 Substitute value behavior esc eccvsdedectudedselsseacvyacoresesuccoeeaed detdeyss cavepiudaon sesdiedtacdeareeaceemupmeedaatte 10 EE i 1a 0 sac ee E EE E E E Aa EE AE E E a lke 10 16 Par amet
4. EN 61000 4 2 IEC 61000 4 2 Electromagnetic fields EN 61000 4 3 IEC 61000 4 3 Fast transients burst EN 61000 4 4 IEC 61000 4 4 Transient surge voltage surge EN 61000 4 5 IEC 61000 4 5 Conducted interference EN 61000 4 6 IEC 61000 4 6 Noise emission test according to EN 61000 6 3 Radio interference properties EN 55022 Approvals For the latest approvals please visit www phoenixcontact net catalog 5g 25 g 11 ms period half sine shock pulse 10g Criterion B 6 kV contact discharge 8 kV air discharge Criterion A Field intensity 10 V m Criterion B 2 kV Criterion B DC supply lines 0 5 kV 0 5 kV symmetrical asymmetrical field bus cable shield 1 kV Criterion A Test voltage 10 V Class B 7992 _en_02 PHOENIX CONTACT 5 AXL BK PN ME 5 Internal circuit diagram H x Ki Axio bus Usus u 24V Figure 1 Internal wiring of the terminal points Key FE Optional functional earth ground connection Service Service interface Reset Reset button RJ45 interface Microprocessor Power supply unit LED He INI 3 7992_en_02 PHOENIX CONTACT 6 AXL BK PN ME 6 Connecting PROFINET and supply 6 1 Connecting PROFINET Connect PROFINET to the bus coupler via an 8 pos RJ45 connector a Observe bending radii The housing dimensions specified under Di mensions refer to the bus coupler with I O con nectors without Ethernet
5. the PROFINET IO controller Please integrate the corresponding GSDML file of the bus coupler into the rel evant software tool STEP 7 HW Config the FDCML GSDML file and the latest docu mentation for the bus coupler The latest files and documentation can be found on the Inter net at www phoenixcontact net catalog A Make sure you always use the latest version of 17 Firmware update In order to update the firmware of the bus coupler the device must be provided with a firmware container via a TFTP server You can use any TFTP server e g Factory Manager note describes how to update the firmware us ing the Factory Manager This document can be found on the Internet at www phoenixcontact net catalog A The TFTP FIRMWARE UPDATE application Please refer to the Diagnostic indicators for PROFINET sec tion for the LED states during the firmware update 7992_en_02 PHOENIX CONTACT GmbH amp Co KG 32823 Blomberg Germany www phoenixcontact com 11
6. AXL BK PN ME Axioline bus coupler for PROFINET IO Data sheet 7992 _en_02 PHOENIX CONTACT 2012 07 09 1 Description The bus coupler links a PROFINET IO network with the Axioline system Up to 63 Axioline devices can be connected to an existing PROFINET system using the bus coupler For startup tests you can put the Axioline station into opera tion independent of the higher level network either using the service interface or an Ethernet port at the bus coupler Features Connection of up to 63 other Axioline devices 2 Ethernet ports with integrated switch Typical cycle time of the Axioline system bus 10 us approximately PROFINET RT Minimum cycle time of PROFINET for RT is 250 us Runtime in the bus coupler is negligible goes to 0 us Firmware can be updated Diagnostic and status indicators This data sheet is only valid in association with the UM EN AXL SYS INST user manual For information on PROFINET basics please refer to the UM EN PROFINET SYS user manual It can be downloaded from the product at www phoenixcontact net catalog A Make sure you always use the latest documentation Here you will also find the current GSDML file D OGD OO GD GD OGD OO OD Lorrie GD INSPIRING INNOVATIONS AXL BK PN ME 2 Table of contents 1 DGSCHIDUOM ERA Ee EE EAE A EE E 1 2 Table of CONS IS ai chk ics cade ue es areas ate a E ea ee EA Aa AE Aa eNO Ere E E deaa
7. Technical data Dimensions nominal sizes in mm 75 Width Height Depth Note on dimensions General data Color Weight Ambient temperature operation Ambient temperature storage transport Permissible humidity operation Permissible humidity storage transport Air pressure operation Air pressure storage transport Degree of protection Protection class Connection data Connection method Conductor cross section solid stranded Conductor cross section AWG Interface PROFINET Number Connection method Transmission speed Transmission physics Transmission length Interface Axio bus Connection method Transmission speed 40 mm 123 6 mm 75mm The depth is valid when a TH 35 7 5 DIN rail is used according to EN 60715 gray 173g 25 C 60 C 40 C 85 C 5 95 according to DIN EN 61131 2 5 95 according to DIN EN 61131 2 70 kPa 106 kPa up to 3000 m above sea level 70 kPa 106 kPa up to 3000 m above sea level IP20 lll IEC 61140 EN 61140 VDE 0140 1 Spring cage connection with direct plug in method 0 2mm 1 5mm 24 16 2 RJ45 female connector auto negotiation and autocrossing 100 MBit s Full duplex Ethernet in RJ45 twisted pair max 100 m Connection for bus base module 100 MBit s 7992_en_02 PHOENIX CONTACT
8. connection When installing the bus coupler in a control box ob serve the bending radii of the Ethernet cables RJ45 Pina and the connectors used e g FL CAT5 FLEX Pin 2 30 mm for fixed installation and Pin 3 FL CAT5 HEAVY 30 mm without outer sheath Bini and 45 mm with outer sheath If required use angled RJ45 connectors to maintain these a Pin 5 bending radii Pin 6 PIN 6 2 Connecting the supply voltage terminal point Pin 8 assignment Figure 2 Pin assignment of the Ethernet socket RJ45 Only one twisted pair cable with an impedance of 100 Q may m al be connected to each Ethernet interface in RJ45 format The data transmission speed is 100 Mbps The 100Base TX port a a2 of the bus coupler is able to detect a pair of incorrectly con b1 nected receive cables RD RD and to correct them using cq the auto polarity correction function b2 For the pin assignment please refer to the following table Jg Pin Assignment 1 TxD transmit data Figure 3 Terminal point assignment 2 TxD transmit data 3 RxD receive data Termi Color Assignment 4 Reserved nal 5 Reserved point 6 RxD receive data Supply voltage input 7 Reserved al a2 Red 24 V DC Communications power 8 Resewad UL supply internally bridged b1 b2 Blue GND Reference potential of the Auto crossover supply voltage internally a Both Ethernet interfaces are provided with the br
9. erizatiOn i eissviesinriniiien Get enearo eeii eerie oo a aAA EEE AAA RA NETA NAAKKA TEAKE ia 11 7 Firmware updaten nnne iea ienaa a adaa oae EEEH aa A AA EE EA EELEE 11 7992_en_02 PHOENIX CONTACT 2 AXL BK PN ME 3 Ordering data Description Axioline bus coupler for PROFINET IO including bus base module and connector Axioline bus coupler for PROFINET IO electronic module as a replace ment for item 2688019 AXL BK PN Accessories Power plug for Axioline bus couplers AXL BK RJ45 connector shielded with bend protection sleeve 2 pieces gray for straight cables for assembly on site For connections that are not crossed itis recommended that you use the connector set with gray bend protection sleeve Plug Adapter RJ45 connector shielded with bend protection sleeve 2 pieces green for crossed cables for assembly on site For connections that are crossed it is recommended that the connector set with green bend protection sleeves is used Plug Adapter CAT5 SF UTP cable J O2YS ST C HP 2 x 2 x 24 AWG heavy duty instal lation cable 2 x 2 x 0 22 mm solid conductor shielded outer sheath 7 8 mm diameter inner sheath 5 75 mm 0 15 mm diameter Cable con ductor CAT5 SF UTP cable J LIO2YS ST C H 2 x 2 x 26 AWG light duty flexi ble installation cable 2 x 2 x 0 14 mm stranded shielded outer sheath 5 75 mm 0 15 mm diameter Cable conductor Crimping pliers for assemblin
10. est of an Axioline device ON There is at least one maintenance request of an Axioline device e g device temperature at permissible limit RDY Green Ready ON Device ready to operate OFF Device not ready to operate Flashing Device booting for firmware update with boot requests D Red Diagnostics Red ON Bus error yellow Yellow READY Device is ready to operate no data is exchanged green ON Yellow I O error in ACTIVE flashing Green RUN Data exchange status and data from the higher level system is ON transmitted Green ACTIVE Configuration is active data exchange with invalid process flashing data Green I O error in RUN yellow al ternating LNK 1 2 Green Link port 1 2 ON Connection via Ethernet to a module via port 1 2 established Flashing PROFINET module identification flashing OFF No connection established via port 1 2 7992_en_02 PHOENIX CONTACT 8 AXL BK PN ME Designation Color Meaning State Description ACT 1 2 Yellow Activity port 1 2 ON Transmission or reception of Ethernet telegrams at port 1 2 OFF No transmission or reception of Ethernet telegrams at port 1 2 9 Diagnostic indicators for PROFINET States during operation LED Meaning SF OFF PROFINET IO controller was able to establish BF flash communication without errors ing States in the event of an error States durin
11. g firmware update LED RDY flash ing RDY ON M ON Meaning BootP requests are sent and the firmware con tainer is loaded via tftp Firmware is saved LED Meaning Measure remedy in the The firmware update can take several minutes event of an error The bus coupler is restarted automatically after SF OFF PROFINETIO No error a successful update BF flash device is waiting ing for communica tion with the H PAOFINETIO 10 Diagnostic alarms controller PROFINET IO enables the PROFINET IO device to store di The logic com Check the connection be agnostic information together with the error location and error munication path tween the PROFINET IO type has been inter controller and the In the default upon delivery the alarms are enabled however rupted The PROFINET IO device Make they can be disabled with parameters on startup PROMETO aS MALINS PROEINE KAS An incoming alarm informs the PROFINET IO controller that controller can no vice name of the ae longer be ac PROFINET IO device is iden 2 gnostic information has been stored cessed tical with the configuration When the diagnostic information has been removed an out The Assign the PROFINET de going alarm is transmitted to the controller PROFINETIO vice name using the relevant If at least one piece of diagnostic information is stored the SF device is not as tool LED is on If no diagnostic information is presen
12. g the RJ45 connectors FL PLUG RJ45 for assembly on site Tools Programming adapter with USB interface for programming with the IFS CONF MACX MCR CONMF and UPS CONF software Cable conductor Zack marker strip for Axioline device labeling in 2 x 20 3 mm pitch un printed 25 section for individual labeling with B STIFT 0 8 X PEN or CMS P1 PLOTTER Marking Zack Marker strip flat Strip white Unlabeled Can be labeled with Plotter Mounting type Snap into flat marker groove For terminal block width 10 15 mm Lettering field 4 of 10 15 x 5 mm and 1 of 5 8 x 5 mm Marking Software for starting up and parameterizing Axioline stations Documentation User manual English Axioline System and installation User manual English PROFINET basics Application note English Firmware update for devices supporting a TFTP firmware update Type AXL BK PN AXL BK PN ME Type AXL CN L UL FL PLUG RJ45 GR 2 FL PLUG RJ45 GN 2 FL CAT5 HEAVY FL CAT5 FLEX FL CRIMPTOOL IFS USB PROG ADAPTER ZB 20 3 AXL UNPRINTED ZBF 10 5 8 AXL UNPRINTED STARTUP Type UM EN AXL SYS INST UM EN PROFINET SYS AH EN TFTP FIRMWARE UPDATE Order No 2688019 2688132 Order No 2700979 2744856 2744571 2744814 2744830 2744869 2811271 0829579 0829580 2700636 Order No Pcs Pkt 1 Pcs Pkt 25 50 Pcs Pkt 7992_en_02 PHOENIX CONTACT 3 AXL BK PN ME 4
13. idged auto crossover function Shielding The shielding ground of the connected twisted pair cables is electrically connected with the socket When connecting network segments avoid ground loops potential transfers and voltage equalization currents via the braided shield 7 Connection example pl PROFINET E I 24VDC UL M Figure 4 Connection of the cables 7992_en_02 PHOENIX CONTACT 7 AXL BK PN ME 8 Local status and diagnostic indicators OBUBOSEUEA Ql SF BF M RDY D LNK1 ACT1 LNK2 ACT2 Figure 5 Local status and diagnostic indicators Designation Color Meaning State Description UL Green ULogic ON Communications power supply present OFF Communications power supply not present SF Red System failure ON PROFINET diagnostics available PROFINET OFF PROFINET diagnostics not available Flashing Flashes only together with the BF LED watchdog triggered BF Red Communica ON No link status available on any port tion error BusFail Flashing SF LED not flashing Link status available no communication con nection to the PROFINET IO controller Flashing SF flashing Hardware watchdog triggered OFF A PROFINET IO controller has established an active communication connection to the PROFINET IO device M Yellow Maintenance OFF There is no maintenance requ
14. rmware is started After com pletion of the firmware boot process the BF LED is either on or flashing Reset button The reset button is on the front of the bus coupler The bus coupler is restarted by pressing the reset button The outputs of the station are set to the parameterized substitute values The process image of the inputs is not re read Documentation i How to assign the PROFINET names and the IP address as well as how to startup a device within a PROFINET IO system is described in the following documents PC WORX quick start guide Configuring INTERBUS devices in a PROFI NET IO network using the example of STEP 7 quick start guide For the order designations please refer to the odering data The documentation can be found on the Inter net at www phoenixcontact net catalog 7992_en_02 PHOENIX CONTACT 10 AXL BK PN ME 16 Parameterization PC Worx Parameterization of the PROFINET IO devices in PC Worx requires at least PC Worx version 6 0 It is part of the AUTO MATION Suite 1 50 service pack 3 An online data sheet of the device with important technical data and a configuration file are integrated into PC Worx If several versions of the configuration file are available make sure that you are working with the file version that corre sponds to the firmware hardware version used Other tools The PROFINET IO device is parameterized using the config uration tool of
15. t the SF LED signeda is off PROFINET de vice name SF OFF The physical Restore the physical connec 11 Device replacement BF ON communication tion between the Devices can be replaced without having to reconfigure them path has been PROFINET IO controller and within the PROFINET network The station name and address interrupted The the PROFINET IO device are assigned by the control system to the newly added PRO PROFINET IO FINET bus coupler using the neighborhood detection func controller can no tion longer be ac cessed SF ON Diagnostic data Read the diagnostic mes BF OFF is available sage using the relevant tool SF flash Hardware Execute a reset Replace the ing watchdog has _ device when the error occurs BF flash been triggered again ing 7992_en_02 PHOENIX CONTACT 9 AXL BK PN ME 12 The Phoenix Redundancy Layer PRL makes it possible to design a redundant system with two PROFINET controllers One controller is configured as the primary I O controller and the other as the backup I O controller Depending on which PROFINET controller provides valid values the bus coupler operated at field level adopts these values or uses failsafe val ues The bus coupler supports PRL as of Firmware Version 1 20 a Phoenix Redundancy Layer PRL PRL or shared device and MRP can be used simultaneously if the PROFINET update time is gt 8ms and the PROFINET watchdog time is gt 200 ms
Download Pdf Manuals
Related Search