PDF user`s guide
Contents
1. 4 i C Closing valve 4 ly ne led valve 5 Closing valve 5 e N 7 AS led valve 6 Closing valve 6 e N For Multipla 9V LCD p n 8060 Elder Multipla 9V LGD User manual Page 3 The TEST function can be used to perform a quick check on the system that will ensure its correct operation by activating a given valve manually for a preset duration of 5 minutes If there is a watering cycle in progress it can be interrupted by pressing the TEST and START buttons Press the TEST button repeatedly to select and activate one of the lines after a few seconds the relative valve will open for 5 minutes To close the valve being tested before the end of the 5 minutes press the TEST and START buttons simultaneously The display indica tes the operating mode TEST the line selected and the time remaining 2 For Multipla 9V LCD p n 8060 During a watering cycle the Multipla activates all of the valves on lines 1 to 6 for which a watering time has been programmed using the LINE SELECTORS opening them in succession and in ascending order A watering program consists in the repetition of a watering cycle at intervals programmed with the FREQUENCY selector Having decided which lines are to be activated turn the LINE selector for each one until it is positioned on the required time Watering can be programmed for a duration of between 5 and 60 minutes To exclude watering2. Godes Multipla 9V LED User manual Page 1 Fix the timer to a wall in a covered location sheltered from weather and splashing water ambient temperature between 0 and 50 C Do not install the timer outdoors or in underground valve box 0o T 00 0 0 8 4 yp 0 UW i ts max 50 C 0 mo bg eT AN 0 O boQ NE TENT min 0 C For Multipla 9V LCD p n 8060 Electrical connections 2 x 9Volt ALCALINE max 50 m cross section 1 5 mm Rain Sensor optional Line valves bistable For Multipla 9V LCD p n 8060 Elden Multipla 9V LGD User manual Page 2 Remove the cover of the battery pocket from its seat connect the batteries and position them in the pocket applying light pressure Use only new 9 volt alkaline batteries type IEC 6LR61 Refit the battery cover The appliance is able to operate with one battery only although the life of the battery will be shorter about 6 months with a daily watering program using four lines For Multipla 9V LCD p n 8060 On fitting the batteries the timer automatically runs a test cycle closing all the valves during which each of the Leds will blink once in turn led valve1 Closing valve 1 W ZN ZN led valve 2 7 A A Closing valve 2 N ly AS ZFS led valve 3 A a ay Closing valve 3 e N ly A e N led valve
3. ay from 10 min to 20 min here will be no change to the duration of the watering step already in progress on line 2 whereas the new setting of 20 minutes will take effect with the activa tion of line 3 changing the position of the FREQUENCY selector say from 8 to 12 hours the new setting will take effect within 24 hours subsequent to the change being made thereafter the watering cycles will be repeated at the new frequency selected whilst the START time remains unchanged TA from 8h to 12h from 10 min to 20 min x b 24h from 10 min to 20 min Frequency For Multipla 9V LCD p n 8060 eer Multipla 9V LED Usermanual Page 7 The STOP function interrupts the watering cycle currently in progress Watering will restart as normal with effect from the cycle subsequent to the selected pause as programmed by positioning the FREQUENCY selector The STOP function can also be used to close a valve manually when activated in TEST mode Q For Multipla 9V LCD p n 8060 The RESET function closes the valve if currently open and switches the timer OFF Watering will be suspended until the START button is pressed again or until a TEST is run To RESET the timer press the START and START buttons simultaneously and hold for 5 seconds The message OFF appears in the display For Multipla 9V LCD p n 8060 For more information and additional details consult the instruction booklet accompanying the product
4. e currently active and the number of minutes remaining until watering is due to finish on that line The valve currently open is also indicated by the relative Led which blinks On completion of the watering cycle the standby signal reappears in the display with the time remaining until the start of the next watering cycle example of watering cycle with FREQUENCY selector set to 8h 2 Example of watering cycle with FREQUENCY selector set to 8h sly OO led valve 1 For Multipla 9V LCD p n 8060 Elder Multipla 9V LGD User manual Page 6 Example of programming at 16 30 the duration is selected for all of the watering lines LINE selectors and the frequency is set at 8h FREQUENCY selector Suppose that watering is not to start immediately but at 22 30 i e after 6 hours press the START button once and then six times in succession so that the display shows 6 00 The time indicated in the display begins counting down ultimately reaching 0 00 at 22 30 the watering cycle starts and will then be repeated every 8 hours as set with the FREQUENCY selector i e at 22 30 at 06 30 and at 14 30 1 16 30 Frequency For Multipla 9V LCD p n 8060 To change a watering program currently in use enter the new LINE and FREQUENCY settings as desired The change will be rendered effective by the timer when appropriate Examples with watering in progress and line 2 active the position of the LINE selectors is changed s
5. on a given line on the other hand position the corresponding selector on zero 2 VI led valve 1 X s Line 1 led valve 2 aoe a IN led valve 3 se e led valve 4 X a led valve 5 X a VU led valve 6 ax s Line 2 Line 3 For Multipla 9V LCD p n 8060 Gobe Multipla 9V LED Usermanual Page 4 To set the watering frequency turn the FREQUENCY selector to the required position every 8 12 or 24 hours or 2 3 4 or 7 days For Multipla 9V LCD p n 8060 To start the program immediately press the START button once The next watering cycle will begin after the time period set with the FREQUENCY selector has elapsed example pressing the START button at 20 00 hours to activate the program with the FREQUENCY set at 8 hours the next watering cycle will commence at 04 00 hours Start V For Multipla 9V LCD p n 8060 eels Multipla 9V LGD Usermanual Page 5 To delay the start of the program press the START button a second time before 5 seconds have elapsed to set a delay of one hour a third time for two hours and so on up to as many as 23 hours The display momentarily indicates the number of hours delay selected then the watering standby signal appears together with the time remaining until the start of the first cycle Q For Multipla 9V LCD p n 8060 When a watering cycle is in progress the display shows the in progress symbol the number of the lin
Download Pdf Manuals
Related Search