Home
Pyle® Motorcycle/ATV/Snowmobile Speakers Users
Contents
1. gt 600 Watts Motorcycle ATV Snowmobile Mo nt Amplifier w Dual df handle bar Mount Aluminum Diacast ame progi speakers w MP3 lpod Input and USB Charger m Watts Motoroycle ATV Snowmobile Mount ae w Dual Ben Mount SNR Spon speakers w MP3 lpod Input USER S MANUAL Congratulations on your purchase of this Pyle Cycle Series premier amplified speaker system Like all Pyle products this motorcycle system has been thoroughly tested to ensure consistent reliable performance under some rigorous conditions Our systems were designed to with stand water moisture heat and direct sun exposure We pride ourselves in customer satisfaction If you should have any questions regarding the installation and or operation of your Pyle Cycle Series motorcycle speaker system which is not covered in this manual please contact your Pyle Dealer or Pyle Technical Support What is Included Upon un packing your new Pyle Cycle Series audio system please check to ensure you have all the included parts Part Part with Image PLMCA60 PLMCA30 with Image 1 Pair of 300 Watt Stereo 1 Pair of 200 Watt Stereo Chrome Speaker Enclosures Chrome Speaker Enclosures with Speaker Wires with Speaker Wires 1 Pair of Handlebar 1 Pair of Handlebar Speaker Enclosure P Speaker Enclosure P Shape Clamp Shape Clamp 1 12 Volt Direct Plug for 1 12 Volt Direct Plug for Compatible Motorcycles Compatible Motorcycles 1 USB Char
2. Item 12 one side to our Universal Bracket Item 5 the other to your MP3 player audio source Step 10 Connect 3 5mm male connection into Audio device and opposite side into Micro Amplifier E 2 motorcycle speaker E Frequency Response 280Hz 20KHZ E 20mm KAPTON voice coil E 4 ohm Impedance E SPL 83 dB 1W 1M E Plastic with shinny chromed Speaker housing Dimensions 2 5 W x 2 5 H x 3 75 L E Micro amplifier with harness amp universal mount included Amp dimension 3 25 W x1 25 H x2 L i Amplifier Ae Maat Amplifier ne Mat 1 Screw Washer and Nut 1 Screw Washer and Nut PLMCA60 Blue Male Terminal Blue Male Terminal for Amplifi p E 2 motorcycle speaker E Frequency Response 260Hz 21KHZ plifier for Amplifier Connector Connector E 25mm KAPTON voice coil E4 ohm Impedance E SPL 85 dB 1W 1M E Aluminum with shinny chromed Speaker housing Dimensions 2 5 W x 2 5 H x3 L 1 Universal 12 Volt Wire _ 1 Universal 12 Volt Wire E Micro amplifier with harness amp universal mount included Amp dimension 3 25 W x1 25 H x2 L Harness Connection Harness Connection w USB charge included Dimensions 2 5 W x 1 75 H x 1 5 L E Radio MP3 Mount Dimensions 3 5 L x 0 625 W x 3 125 H BRAND SPEAKERS SPEAKER SYSTEM
3. ger Power Source 1 Pair of Handlebar Music 1 Pair of Handlebar Music 1 Adjustable Rotary 1 Adjustable Rotary Source Mount Z Shape Source Mount Z Shape Volume Control 3 5 mm Volume Control 3 5 mm Clamp Clamp Interface Interface 1 Micro Stereo 2CH 1 Micro Stereo 2CH 1 Black Industrial Velcro Amplifier 300 Wattsx2 Amplifier 200 Watts x 2 Max Output Power Max Output Power Adhesive Strips 1 Universal chrome Handlebar Mp3 Audio Mounf with 2 Black Industrial Velcro 6 Black Wire Tie Lockable 6 Black Wire Tie Lockable Straps Straps 1 Amplifier 12 Volt 1 Amplifier 12 Volt Ground Blue Spade Terminal Ground Blue Spade Terminal 2 Screws for Speaker 2 Screws for Speaker Installation Instructions Specifications PLMCA30 Step 1 Install P shaped clamp Item 2 Z shaped clamp Item 3 threaded on to the bottom of each speaker enclosure Item 1 Use the provided bolts item 14 Step 2 Bolt each speaker with its mount to the handlebar of the vehicle Hardware included will allow for mounting on to 1 diameter and smaller handlebars Project each speaker at desired listening level for best performance Step 3 Secure speaker wires either through handlebars for a custom look or use Item 13 wire ties to secure to the handlebars Step 4 Bolt the rotary volume control Item 11 to the handlebars using the vehicle provided hardware Then run 3 5 mm connection down t
4. o desired amplifier location Use Item 13 wire ties to secure to the handlebars Have 3 5 mm male connection close to mount The Connector that comes pre installed on the amplifier wire harness Item 8 was designed to allow for direct plug in for most American Motorcycles Item 9 If mounting on a metric or universal vehicle this harness will not be used and replaced with the terminals connectors provided in the enclosed parts bag according to the installation instructions Items 6 7 amp 8 Follow wire instructions as shown in Diagram A Be sure to match the proper polarity for all connections The polarity for the speaker terminals solid color wire wire with stripe Blue wire 12 Volt Positive terminal trigger wire Black wire 12 Volt Ground to chassis of vehicle Step 5 Bolt the Universal Handlebar MP3 Audio Mount Item 5 using provided black industrial velcro adhesive strips Item 12 Remove bolt from existing switch housing on motorcycle and secure to bracket Step 6 Only for use with PLMCA60 Bolt the USB Charger Power Source Item 10 using vehicle provided hardware This wire should be connected 12 Volt power source Step 7 Run wires up to neck area of motorcycle and plug into harness Use Item 13 wire ties to the frame Step 8 Bolt amplifier on Motorcycle with provided Bolt item 15 Best if mounted directly to frame out of reach from direct heat or crash bar Step 9 Attach Velcro strips
Download Pdf Manuals
Related Search
Related Contents
TLK300 & TLK2000 ( /V5, /V6 , /V7 & /V8 ) 姫路市コミュニティ・プラント等 運転管理業務委託共通仕様書 姫路市 Des entreprises plus innovantes grâce aux stagiaires “Do It Right” User's Guide DCR-PC3E ダウンロード - ソニー製品情報 Copyright © All rights reserved.
Failed to retrieve file