NextDesk Solo Assembly
Contents
1. next desk Solo Assembly Instructions Preface We are delighted that you have chosen NextDesk Congratulations you have selected the most advanced and sophisticated power adjustable workstation available today Our bodies weren t made to sit or stand for hours at a time Now you have the choice sit or stand with the press of a button This User Manual will provide basic instructions for NextDesk Terra and Air models We are sure that your NextDesk will provide you many years of enjoyment Should you ever experience a problem with any our products please contact us Thank you for choosing Nextdesk We hope you enjoy your NextDesk for many years NextDesk Team Preface AN Table of Contents Safety Wis POC ION RR E 637 Page 1 Unpacking Preparation Tools Needed Page 3 System Components List amp Parts LiSst Li Page 4 Components DIAG ai vss cicseiin cena irnadwdioitwiaveiaraenteniatiGenintages Page 5 Step 1 Connecting Lifting Columns to Desktop Page 6 Step 2 Connecting Floor Supports to Columns Page 7 Step 3 Optional Keyboard Installation If Purchased Page 8 Step 4 Connecting CADI siii aa Page 9 Step 5 Initializing Desk ear Page 10 Step 6 Inserting Support Crossbar vac ccsvwcnscsecinccxnnieetanceessaas Page 11 Step 7 Cable ManagemMent sss ssssrrrrrrrrrrrrrrrrrrrrrrrrrerrrr Pag2. EEDED Ii Power Drill aaa a 7 p il Socket g 1 16 Drill Bit enci eon 3 16 Drill Bit a QUICK TIP INSTALLING SCREWS DO NOT over tighten screws during installation 2 A v oe SYSTEM COMPONENTS LIST Desktop control box cable controller mounting plate any accessories attached Lifting Column Back Plate Spacer Shorter of two back plates Back Plate larger of two back plates Decorative Channel with AC power chord attached Retaining Bracket Bars 10 AC Chord Q A A A AA I LS o PARTS LIST 3 Lag Bolts 6 Retaining Bracket Screws Long 4 Lift Mounting Screws 10mm Short 1 Allen Wrench Hex Key 5 32 1 Allen Wrench Hex Key 1 8 5 Adhesive Zip Ties HOS Ny NS J LN v LN v x o COMPONENTS DIAGRAM Microprocessor Control Box Solo Desktop Controller refrence detail below Back Plate Spacer Lifting Column j RE Se _ Retaining Brackets Bakpe e 0 REC cana pt Decorative Channel Microprocessor Control Box Anti Collision Top View Dongle Controller Cable N Lifting Column o o Connector __ _______ Power Cable e PN Mount Assembly Located a stud for suitable mounting 30 or 36__ STUD Take into account the desk will rise approximately 50 inches and is 30 or IMPORTANT 36 wide depending on your or
3. NTIES EXPRESS OR IMPLIED NEXTDESK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS 20
4. PLICABLE WARRANTY PERIOD The applicable warranty period measured from the date of delivery to the original user shall be three 3 years for all warranted desks EXCLUSIONS This warranty does not cover and NextDesk shall not be liable for the following 1 repairs and replacements because of misuse abuse negligence alteration accident freight damage or tampering 2 products which are not installed used and properly cleaned as required in the NextDesk Installation and or Installation Operation Manual for this applicable product 3 products considered to be of a consumable nature 4 Shipping to or from repair center 5 accessories or parts not manufactured by NextDesk 6 charges by anyone for adjustments repairs replacement parts installation or other work performed upon or in connection with such products which is not expressly authorized in writing in advance by NextDesk 19 EXCLUSIVE REMEDY NextDesk s only obligation under this warranty is the repair or replacement of defective parts NextDesk shall not be liable for any direct special indirect incidental exemplary or consequential damages or delay including but not limited to damages for loss of profits or loss of use NO AUTHORIZATION No person or firm is authorized to create for NextDesk any other obligation or liability in connection with the products THIS WARRANTY IS NEXTDESK S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRA
5. a person who is responsible for the safety of these persons J _S v A SAFETY INSTRUCTIONS cont Children must be under close supervision to ensure that they do not play with the product 1 It is important for everyone who is installing or using NextDesk to have the necessary information and access to this User Manual A If there is visible damage on the product it must not be installed NextDesk is not intended for use by young children or for those persons who require supervision Children should be supervised to ensure that they do not use or play with NextDesk Before Installation Reinstallation or Troubleshooting Z Stop NextDesk AN Switch the power supply and pull out the main power supply plug AN Relieve NextDesk of any loads which may be released when unexpected Before Start up Z Y Make sure NextDesk has been installed as specified in this manual AN System Connection the individual parts must be connected before the control box is connected to the main power supply If the control box makes unusual noises or has an odor switch off the main power supply immediately Z Make sure the cables are not damaged A v Carefully remove the packaging from UNPACKING NextDesk and then inspect all components for any shipping damage S A Report any damage to the shipping My company and fill out a concealed damage report Se SI ADDITIONAL TOOLS N
6. der 50 Fi e Zi Mark Stud for Mounting Using the back plate as a template mark stud for three mounting holes STUD IMPORTANT Align bottom of the Back Plate with the floor NI gt y Drill Three Pilot Holes into Stud Using 1 16 drill bit and then follow up with a 3 16 drill bit A IMPORTANT STUD First use 1 16 Drill bit Follow up with a 3 16 A IMPORTANT Place Back Plate Spacer and Back Plate against wall to e verify holes align 00 gt v Attach Spacer and Back Plate Using a Socket Wrench attach spacer and back plate to wall using the 3 1 4 lag bolts provided g Hardware Required 3x 1 4 Lag Bolts IMPORTANT Place spacer smaller plate behind back plate larger plate IMPORTANT Face Counter sunk hole side away from wall gt v Desk Assembly Using 10mm Lift Mounting Screws mount lifting column to underside of desktop 6x 10mm Allen Screws g Hardware Required IMPORTANT Mount with control cable facing toward the center IMPORTANT of the desk Do Not overtighten screws 6 Connect Lift Cable Connect lift cable to control box cable inserted in socket 1 Attach to Solo to Wall Bracket With Two People position solo desk lifter against wall bracket While one person holds the desk lifter against wall bracket the other person attaches each retaining bracket
7. e 12 Operating Controller eMenrr rere Te etre aT erent renner te Crt T tree Page 13 Anti Collision FRAU teorica Page 15 Maintenance amp DESEHPLOf xsse cia aria Page 16 Troubleshooting amp Repalh lee lisa udiiaia Page 17 Warranty Moroccan a Page 18 Table of Contents A A SAFETY INSTRUCTIONS WARNING FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY SAFETY AND OPERATING INSTRUCTIONS AND WARNING REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY The safety of NextDesk clients and users are our primary concern To assure safer operation Read and understand this manual before attempting to install or operate NextDesk Assure that everyone who uses NextDesk is informed of the contents of A this manual This is the responsibility of the Purchaser Assure that this manual is located near the NextDesk and if possible permanently affixed to the desk Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components Persons who do not have the necessary experience or knowledge of NextDesk must not use the product Persons with reduced physical or mental abilities must not use NextDesk unless they are under supervision or they have been thoroughly instructed in the use of the apparatus by
8. er cable to control box IMPORTANT Cover sits ground level OPERATING CONTROLLER ep Display Adjust Up Adjust Down Memory 1 2 38 Store Memory Up and Down Q Press either the up or down button for parallel drive and the system will drive until the button is released again or the system reaches end position Programmable Memory The four small buttons are used for memory drive storing memory Store Memory Presets a Raise or lower the desk to the height you wish to store as a preset b Press and release the 6 button c Within these two seconds press a memory button or co Or the panel will acknowledge by showing 1 2 or 3 in the display depending on chosen position Using Memory Presets Press one of the memory buttons and the system will start driving to the preprogrammed memory position Keep the button pressed until the position is reached Display Function Shows the actual height OPERATING CONTROLLER cont Other Functions Adjusting Initial Height It may be necessary to adjust the displayed height due to different thicknesses of desktops etc The control will display 24 5 inch as the default desk height Procedure a Press Q and Q keys at the same time and keep them pressed for 5 seconds This allows the initial height to be adjusted Until the initial height is adjusted the display will show three minuses Hereafter
9. op of the desk Situations where the anti collision does not work These situations are e If the collision happens during the initialization phase e If the collision happens within the first 1000 milliseconds or after the control button has been released e If the collision happens between the floor and the table and the load on the desk plus the weight of the legs are lower than 40 kg e If the collision happens over too long of a time e g if the collision is with a soft object 16 gt Maintenance Clean dust and dirt on the outside of NextDesk and other components at regular intervals and inspect them for damage and breaks Inspect the connections cables and plugs and check for correct functioning as well as the security of the connection points The cleaners and disinfectants must not be highly alkaline or acidic pH value 6 8 A WARNING The NextDesk systems do not withstand oil Description of the NextDesk Each NextDesk actuator lifting column is equipped with a motor and synchronicity is ensured by means of software that also takes account of an oblique load on the desk Soft start and stop are also part of this software which ensures a soft start and stop when adjusting the desk Maximum Duty Cycle Irrespective of the load the duty cycle of 10 6 min hour or max 2 min at continuous use must NOT be exceeded as this will result in overheating of the motor and control box Exceeding the dut
10. sandwiching the lift between the back plate and retaining bracket g Hardware Required 6x M6 Retaining Screws IMPORTANT Face Counter sunk hole side away from wall A IMPORTANT i Do Not overtighten screws Bracket should be snug but should not crush unit 1140 Initialize Desk A Using 10 power cable temporarily connect the lift control box to a power supply For desks with Power Management the power cord is factory attached For desks without Power Management plug power cord into the control box prior to connecting to wall outlet B Press and hold the button until the lifting columns have completely retracted and continue to hold for 5 seconds after all movement stops C Once the columns are completely retracted they will automatically run approximately 5 mm out again and then slowly run in again Do not release the 9 button until 5 seconds after all movement has completely stopped Note It is sometimes necessary to press the button twice to start initialization There may be a short delay before movement begins Note If the button is released before the sequence is complete then initialization is interrupted and the process must be started again from the beginning gt 12 Slide on Decorative Cover Connect Power Raise Solo desk two feet by pressing the Q button Remove temporary 10 power cable from control box Connect sleeve integrated pow
11. the display will revert to showing the height b The height can then be adjusted by either Q or until desired height has been reached The system will return to normal operation and give a short blink after 5 seconds of inactivity on the keys 15 ANTI COLLISION FEATURE NextDesk offers an anti collision feature that can limit material damages to a desk if a collision with a solid object should occur Enabling the anti collision To enable the anti collision function a dongle must be mounted in one of the two control ports of the control panel on the underside of NextDesk The function is only active when the dongle is mounted Anti Collision If you remove the dongle the anti collision function is disabled Dongle Inspect NextDesk prior to use to determine if the anti collision dongle is properly inserted Do not use NextDesk if the anti collision dongle has been removed Method of operation The control box monitors the electric consumption on each lifting column If the electric consumption on one channel is increased more than a predefined slope a collision is assumed All channels are stopped immediately and all desk legs will start to run in the opposite direction approximately 50 mm The anti collision sensitivity is different in up and downward direction Upwards the force is approximately 20 kg Downwards the load will be approximately 40 kg the load on the desk lifting column the desk what is on t
12. y cycle will result in a dramatic reduction of the life of the system 17 Troubleshooting and Repairs Error Codes Below are the possible error codes which may be displayed on the controller Eraro pero Sten Lifting columns are in an Initialize or Reinitialize unknown position Refer to Page 10 Overload in upwards directionhas occurred Reduce the weight on NextDesk direction has occurred downward movement Release all buttons amp press a valid legal RENS AFE ERREN button or button combination Overload in downwards Remove objects that prevent Repairs In order to avoid the risk of malfunction all NextDesk repairs must be carried out by authorized NextDesk repair centers as special tools and gaskets must be used WARNING If any of the NextDesk products are opened there will be a risk of subsequent malfunction 18 gt Limited Warranty SCOPE OF WARRANTY Next Technologies Inc NextDesk warrants to the original purchaser its new desks except for components not warranted under Exclusions manufactured by NextDesk to be free from defects in material and workmanship under normal use and service NextDesk s obligation under this warranty is limited to the repair or replacement at NextDesk s option of the parts or the products the defects of which are reported to NextDesk within the applicable warranty period and which upon examination by NextDesk prove to be defective AP
Download Pdf Manuals
Related Search