SMARTPONG - Affordable Table Tennis
Contents
1. Lift up the robot Take out the balls form undercarriage Check to see if the balls are squished distorted or wrongly size If so do not put the Evacuate the balls on undercarriage balls in to the machine System Remote controller Brief Instructions for Troubleshooting Remarks 1 This device does not require any modification If any breakdown occurs check the following to solve problems 2 Until the problem is solved make sure to turn the power off to avoid damage Problem A System fails to start B Ball service tray is blocked with balls Buzzer beeps C Weak abnormal or failed service balls D The system works but does not respond to the remote controller E No display on LCD F Memory function does not work yourself 3 If your problem is not found in the list please contact the dealer Never try to reassemble it by 4 lf the ball is obstructed the system will keep repositioning itself to the default position Cause 1 Power is not turned on 2 Ball Service tray is blocked 3 Remote control distance is too far from the system or there is an obstacle in between 4 No power 5 Failure of remote controller 1 Blocked with balls or other objects 1 The transparent cap is not tightly sealed 2 There is not any ball on the ball service tray because the ball is blocked in the left right ball collecting tray 3 The ball service tray is blocked with a bal2. Place your both hands at the sides of the base to lift the whole system and insert the front tubes under the table at 45 while aiming the tip of the triangle clamp to the middle line of the table 8 Plug one end of the power cord to the robot AC power input and the other to the AC outlet 9 The system is now ready to operate with the control of the remote controller See P10 P11 Please Note If a ball or any object becomes obstruct somewhere the buzzer will beep for 2 to 3 minutes then the system will start repositioning Please turn off the power until the problem is solved Disassembly lt takes only 2 minutes to disassemble this system 1 Unplug the AC power cord 2 Place your hands beside the base lift the whole system slightly and pull it back Then you may place the whole system on the table 3 Gather the balls from the left and right ball collecting trays in the base then place the ball separators from the sides to stop the balls from falling 4 Draw in the left and right pipes and gather them in the base 5 Return the ball collecting trays upwards to their Original positions both sides 6 Draw out the pipes of both sides from the iron tubes and insert them to the holes at the left and right sides of the supporting bracket A switching power supply is built into the system to accommodate all international voltages AC 88V 240V e After plugging the robot server head will rotate to its ready positi
3. SMARTPONG SMARTest ping PONG robot in the world 1 N INSTALLATION AND TROUBLESHOOTING BRIEF INSTRUCTION GUIDE SMARTPONG We appreciate very much for your purchase of the SMARTPONG The microcomputer fully automatic table tennis robot For detailed information please refer to the USER S MANUAL Cautions 100 pieces of 40mm balls has been enclosed in packing carton When the balls are squished please do not put it into machine to avoid damage When the balls are exhaustived buy 40mm balls Methods to Install Table Tennis Robot onto the Table 1 When the table thickness is 25 mm use the No 1 pad when the table thickness is 21mm use the No 3 4 pad when the table thickness is 17 mm use the No 1 2 pad 2 For trial shots exercise the auto 1 auto 5 and auto 8 automatic mode to adjust to the appropriate frequency If the balls do not fall upon the table it means incorrect installation Pads should be replaced by adequate ones or just put in pads and adjust until balls all fall upon table under auto 1 5 8 mode Example for reference shown as bwlow AUTO 1 Frequency 20 AUTO 5 Frequency 15 AUTO 8 Frequency 5 Steps to Install the Ball Blender Device to Prevent Balls from Obstructing Operation l ILLUSTRATE instructions 1 Load motor A on the center trough of undercarriage 2 Put 2 screws B into the hole then fasten them 3 Put plug C into outlet D Table Ten
4. ill exists send it to repair center 3 Replace with new battery 4 Aim the remote controller at the system directly 1 Replace with new battery 2 Check the pole direction of battery 3 Send it to repair center 1 Please refer to the USER S MANUAL P19 21 to restart memory setting 2 Send it to repair center
5. l or other objects 4 Ball too small 38 mm 5 The spring of the ball service tube is broken 1 The conductive plastic of the remote controller is aging 2 Invalid service modes under AUTO MODE only the runtime ball service frequency and memory modules are available 3 Insufficient battery power for the remote controller 4 Remote controller does not aim at the system correctly 1 Insufficient battery power 2 Opposite battery direction 3 LCD breakdown 1 Incorrect memory settings 2 PCB failure Solution 1 Check if the power cord is plugged in 2 Refer to B 3 Shorten the distance of remote control or move away the obstacle If this does not work out the system or remote controller could have failed Send it to repair center 4 Replace the fuse 5 Refer to D 1 blocked with balls turn off the power first Remove the transparent cap and measure the diameter of the ball Do not use any oversized or flat balls to avoid blockage 2 Blocked with unspecified objects or conflicted with the ball service gear 1 Reseal the transparent cap tightly 2 Put the ball in the left right ball collecting tray back to the ball service tray 3 Check the ball service tray and remove the blocked ball or object if any 4 Use the international standard 40 mm balls 5 Send it to repair center 1 Send it to repair center 2 Please refer to the USER S MANUAL of the remote controller If problem st
6. nis Robot Assembly and Disassembly Assembly To optimize the performance of this robot make sure to follow the assembly instructions as below The assembly of this robot is very easy No special tools are required If you follow the following steps you can complete the assembly within 5 minutes 1 When you take the robot from the packing carton please hold the iron pipe with one hand and the base with the other The back of the robot server should be face towards the user and be placed on the table 2 Withdraw the pipes from both sides of the base and insert them into the straight iron tube 3 Lift the left and the right ball collecting tray then put them down carefully 4 Pull out the triangle bracket in front of the robot Supporting bracket at the bottom then open the left and the right pipes Left Right Pipe Transparent Cap Ball Separator Base Undercarriage or ball service tray 5 Right Pipe Left Pipe Left Right Ball collecting tray ball track Server Head Infrared Sensor Middle Pipe A The system robot server O 5 Based on the thickness of the table attach the appropriate pads to the left and the right pipes in the front When the table thickness is 25mm use the No 1 pad when the table thickness is 21mm use the No 3 4 pad when the table thickness is 17mm use the No 1 2 pad 6 Load motor on the center trough of Base put 2 screws on the hole then fasten them 7
7. on When the remote controller is turned off while aiming at the infrared sensor at the system the system will also return to its original position e Please unplug the AC power cord if the system is not to be in use for a period of time e lf the left or the right ball collecting tray is taller than the tabletop the balls will not fall on the table so the pads should be changed to decrease the angle of elevation e Before putting the balls into the machine please make sure their sizes are standard to avoid possible breakdown of the system Never use balls other than 40 mm Cleaning and Maintenance How to Clean the Shell A soft piece of cloth is sufficient for moderate soiling If the system becomes dirty please prepare a 1 6 solution of soap and water and clean with a soft piece of cloth then dry with another dry cloth Never use strong solvents such as alcohol benzene or other volatile cleansers To avoid accidents always unplug the power cord of the system while cleaning this device How to Maintain the System Please wash the table tennis balls regularly to remove dusts and hairs because these can cause a malfunction of the system If the balls are distorted squished or wrongly size stop using them to prevent further damage to system Solutions for the Balls are Obstructed Loosen the butterfly shape nut Install the ball separation board Into undercarriage As figure shown below f Na de
Download Pdf Manuals
Related Search