Home

TOSHIBA L10 Series

1. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Wi Reorient or relocate the receiving antenna Wi Increase the separation between the equipment and receiver W Connect the equipment into an outlet on a circuit different from that to which the receiver is connected W Consult the dealer or an experienced radio TV technician for help Only peripherals complying with the FCC class B limits may be attached to this equipment Operation with non compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception Shielded cables must be used between the external devices and the computer s external monitor port USB port serial port parallel port PS 2 mouse keyb
2. 1600 x 1200 256 256K 256 256K 60 Virtual 75 85 1920 x 1440 256 256K Virtual 256 256K 60 N Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode F Some models in this series are equipped with an 855GME display chipset D This chipset supports the following video modes in addition to the modes shown in Table 2 User s Manual B 4 Display Controller and Modes Table 2 Video modes 855GME Resolution LCD colors CRT colors 1920X1440 256 256K 256 256K Virtual 2048X1536 256 256K 256 256K Virtual Table 2 Video modes 852GM continued Resolution LCD colors CRT colors 640 x 480 64 64K 64 64K 800 x 600 64 64K 64 64K 1024 x 768 64 64K 64 64K 1280 x 1024 64 64K 64 64K Virtual with XGA Panel only 1400 x 1050 64 64K 64 64K Virtual with XGA Panel only 1600 x 1200 64 64K 64 64K Virtual 1920 x 1440 64 64K 64 64K Virtual Vertical frequency Hz 60 75 85 60 75 Vertical frequency Hz 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 60 75 85 60 User s Manual B 5 Display Controller and Modes IN Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode F Some models in this series are equipped with an 855GME display chipset This chipset supports the following video modes in addition to the modes shown in Table 2 Table 2 Video modes 85
3. 4 Connect the AC adaptor to the computer and the power cord to a power outlet The Battery indicator should glow orange to indicate that the battery pack is being charged If the Battery indicator does not glow power is not being supplied Check the connections for the AC adaptor and power cord 5 Charge the battery pack until the Battery indicator glows green Wi f you have extra battery packs rotate their use E Ifyou will not be using the system for an extended period more than one month remove the battery pack Wi Disconnect the AC adaptor when the battery is fully charged Overcharging makes the battery hot and shortens life Wi f you are not going to use the computer for more than eight hours disconnect the AC adaptor Wi Store spare battery packs in a cool dry place out of direct sunlight User s Manual 6 10 Power and Power Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one The life of the battery pack is generally about 500 recharges If the Battery indicator flashes orange shortly after fully recharging the battery the battery pack needs to be replaced You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source This section explains how to remove and install the battery pack Removing the battery pack To replace a discharged battery follow the steps
4. B Memory circuits are exposed to static electricity or electrical noise Restarting the computer Certain conditions require that you reset the system For example if E You change certain computer settings Wi An error occurs and the computer does not respond to your keyboard commands E There are three ways to reset the computer system 1 Click start then click Turn off computer From the Turn off computer menu select Restart 2 Press Ctrl Alt Del to display the Windows Task Manager then select Shutdown and Restart 3 Press the power button and hold it down for five seconds Wait 10 to 15 seconds then turn the power on again by pressing the power button User s Manual 3 12 Getting Started Restoring the preinstalled software If preinstalled files are damaged use the Product Recovery Disc to restore them Restoring the complete system To restore the operating system and all preinstalled software follow the steps below When you reinstall the Windows operating system the hard disk will be reformatted and all data will be lost 1 Load the Product Recovery Disc in the optical media drive and turn off the computer s power 2 Wait 10 to15 seconds then turn on the computer again 3 When In Touch with Tomorrow TOSHIBA appears press the F12 key 4 Usethe up or down cursor key to select the CD ROM DVD ROM icon in the display menu 5 Follow the on screen instructions 6 If your computer ca
5. Software Operating System TOSHIBA Utilities Plug and Play The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T and Fast Ethernet LAN 100 megabits per second 100BASE TX The Wireless LAN feature is not available on all models Where present it supports the B and G standard but it is compatible with other LAN systems based on Direct Sequence Spread Spectrum Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802 11 Standard E Automatic Transmit Rate Select mechanism in the transmit range of 54 48 36 24 18 12 9 and 6 Mbit s IEEE 802 119 E Automatic Transmit Rate Select mechanism in the transmit range of 11 5 5 2 and 1 Mbit s IEEEE 802 11b B Roaming over multiple channels B Card Power Management B Wired Equivalent Privacy WEP data encryption based on 128 bit encryption algorithm W Advanced Encryption Standard AES data encryption based on 128 bit encryption algorithm Windows XP Home Edition or Windows XP Professional Edition operating system and TOSHIBA Utilities and drivers preinstalled on the hard disk Refer to the Software section at the front of this chapter A number of utilities and drivers are preinstalled to make your computer more convenient to use Refer to the Utilities section in this chapter When you connect an external device to the computer or when you install a component Plug and Play capabil
6. Stop W button Stops play Refer to Chapter 4 Operating Basics Display Hinge The display hinge holds the display screen at easy to view angles User s Manual 2 6 The Grand Tour Display Screen TouchPad TouchPad Control Buttons The LCD displays high contrast text and graphics Refer to Display Controller and Modes section in Appendix B Display Controller and Modes When the computer operates on the AC adaptor the display screen s image will be somewhat brighter than when it operates on battery power The lower brightness level is intended to save battery power A TouchPad located in the center of the palm rest is used to control the on screen pointer These let you select menu items or manipulate text and graphics designated by the on screen pointer Refer to the Using the TouchPad section in Chapter 4 Operating Basics User s Manual 2 7 The Grand Tour System amp Keyboard indicators E e Built in HDD Caps Lock NumLock Wireless Activity Power Battery Wireless Activity Built in HDD ODD Caps Lock NumLock System amp Keyboard overlay indicators The Power indicator glows green when the computer is on If you select Standby from Shutdown windows this indicator flashes orange one second on two seconds off while the computer shuts down The Battery indicator shows the condition of the battery s charge Green indicates full charge orange indicates battery c
7. TFT display A liquid crystal display LCD made from an array of liquid crystal cells using active matrix technology with thin film transistor TFT to drive each cell TouchPad A pointing device integrated into the TOSHIBA computer palm rest TTL Transistor transistor logic A logic circuit design that uses switching transistors for gates and storage Universal Serial Bus This serial interface lets you communicate with several devices connected in a chain to a single port on the computer V VGA Video Graphics Array is an industry standard video adaptor that lets you run any popular software volatile memory Random access memory RAM that stores information as long as power is supplied to the computer W warm start Restarting or resetting a computer without turning it off window A portion of the screen that can display its own application document or dialog box Often used to mean a Microsoft Windows window write protection A method for protecting a floppy disk from accidental erasure User s Manual Glossary 12 TOSHIBA L10 Series Index User s Manual A AC adaptor 1 4 additional 1 13 connecting 3 6 ASCII characters 5 7 Battery charging 6 7 extending battery life 6 10 indicator 6 1 location 2 5 Monitoring capacity 6 9 real time clock 1 4 6 4 safety precautions 6 5 save mode 1 10 types 6 3 Battery pack 1 3 additional 7 7 replacing 6 11 C Cache memory 1
8. W Anychange or loss of the recorded contents of CD R RW disc that may be caused by writing or rewriting with this product or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents BW Damage that may be caused by using third party equipment or software Given the technological limitations of current optical disc writing drives you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices Also it is a good idea to make two or more copies of important data in case of undesired change or loss of the recorded contents Writing CD DVDs with the DVD Super Multi drive i Some models in this series are equipped with Writing CD DVDs with the DVD Super Multi drive Supporting Double Layer You can use the DVD Super Multi drive to write data to either CD R RW or DVD R RW R RW RAM discs The following applications for writing are preinstalled RecordNow and DLA licensed by Sonic Solutions InterVideo WinDVD Creator 2 Platinum which is a product of InterVideo Inc Important message DVD Super Multi drive Before you write or rewrite to CD R RW or DVD R RW R RW RAM discs read and follow all setup and operating instructions in this section If you fail to do so the DVD Super Multi drive may not function properly and you may fail to write or rewrite lose data or incur other damage Disclaimer DVD Super Multi drive
9. by U S patents and other intellectual property rights Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Reverse engineering or disassembly is prohibited Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for the TOSHIBA L10 Series Portable Personal Computer at the time of this manual s production However succeeding computers and manuals are subject to change without notice TOSHIBA assumes no liability for damages incurred directly or indirectly from errors omissions or discrepancies between the computer and the manual User s Manual ii TOSHIBA L10 Series Trademarks Intel Intel SoeedStep Centrino Pentium and Celeron are trademarks or registered trademarks of Intel Corporation Windows and Microsoft are registered trademarks of Microsoft Corporation Photo CD is a trademark of Eastman Kodak TruSurround XT WOW XT SRS and C symbol are trademarks of SRS Labs Inc TruSurround XT WOW XT TruBass SRS 3D and FOCUS technologies are incorporated under license from SRS Labs Inc Other trademarks and registered trademarks not listed above may be used in this manual FCC information Product Name TOSHIBA L10 Series Model number PSL10 15 FCC notice Declaration of Conformity Information
10. Aboutrecorded DVDs Some DVD ROM drives for personal computers or other DVD players may not be able to read DVD R R RW RW RAM discs When playing your recorded disc on your computer please use the WinDVD software application If you use an over used rewritable disc the full formatting might be locked Please use a brand new disc User s Manual 4 18 Operating Basics Media care This section provides tips on protecting data stored on your CD DVDs and floppy disks Handle your media with care The following simple precautions will increase the lifetime of your media and protect the data stored on them CD DVDs 1 Store your CD DVDs in the container they came in to protect them and keep them clean Do not bend the CD DVD Do not write on apply a sticker to or otherwise mar the surface of the CD DVD that contains data Hold the CD DVD by its outside edge or the edge on the center hole Fingerprints on the surface can prevent the drive from properly reading data Do not expose to direct sunlight extreme heat or cold Do not place heavy objects on your CD DVDs If your CD DVDs become dusty or dirty wipe them with a clean dry cloth Wipe from the center out do not wipe in a circular direction around the CD DVD If necessary use a cloth dampened in water or a neutral cleaner Do not use benzine thinner or similar cleaner Floppy disks 1 Store your floppy disks in the container they came in to pro
11. Fi F12 B Press Fn F12 ScrLock to lock the cursor on a specific line The power on default is off m User s Manual 5 4 The Keyboard En m Space l Display resolution selection Press Fn spacebar to change the display resolution Each time when you press these hot keys the display resolution changes Fn ae TOSHIBA Zooming Utility reduce To reduce the icon size on the desktop or the application window press the 1 key while holding down the Fn key A om le TOSHIBA Zooming Utility enlarge To enlarge the icon size on the desktop or the application window press the 2 key while holding down the Fn key age Volume decrease Press Fn Down to decrease the sound volume After you press this hot key an icon showing the new setting will be displayed for two seconds age Volume increase Press Fn Up to increase the sound volume After you press this hot key an icon showing the new setting will be displayed for two seconds Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky that is you can press it once release it and then press an F number key To start the TOSHIBA Accessibility Utility click start point to All Programs point to TOSHIBA point to Utilities and click Accessibility User s Manual 5 5 The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows Windows log
12. If the cord is frayed or damaged replace it If the terminals are soiled wipe them with cotton or a clean cloth If the AC adaptor still does not power the computer contact your dealer Battery If you suspect a problem with the battery check the Battery indicator For information on indicator and battery operation refer to Chapter 6 Power and Power Up Modes Problem Procedure Battery doesn t power The battery may be discharged Connect the the computer AC adaptor to charge the battery Battery doesn t charge If the battery is completely discharged it will not when the AC adaptor is begin charging immediately Wait a few minutes attached Battery If the battery still does not charge make sure the indicator does not glow outlet of the AC adaptor is supplying power orange Test it by plugging in an appliance Check whether the battery is hot or cold to the touch If the battery is too hot or too cold it will not charge properly Let it reach room temperature User s Manual 8 5 Troubleshooting Problem Procedure Unplug the AC adaptor and remove the battery to make sure the terminals are clean If necessary wipe them with a soft dry cloth dipped in alcohol Connect the AC adaptor and replace the battery Make sure it is securely seated Check the Battery indicator If it does not glow let the computer charge the battery for at least 20 minutes If the Battery indicator glows after 20 minutes let th
13. Super Multi drive DLA for TOSHIBA DLA Drive Letter Access is the packet writing software which provides the function which writes files and or folders to DVD RW DVD RW or CD RW disc via a drive letter like a floppy disk or other removable disks User s Manual 1 11 Introduction TOSHIBA PC TOSHIBA PC Diagnostic Tool displays basic Diagnostic Tool information about the PC and tests built in devices To start the TOSHIBA PC Diagnostic Tool click start point to All Programs point to TOSHIBA and point to Utilities and click PC Diagnostic Tool TOSHIBAConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network connections ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks To run ConfigFree click start select All Programs followed by TOSHIBA followed by Networking and then click ConfigFree TOSHIBA TouchPad Pressing Fn F9 enables or disables the On Off Utility TouchPad function When you press these hot keys the current setting will change and be displayed as an icon TOSHIBA Touch and TOSHIBA Touch and Launch is a tool that allows Launch you to perform various tasks easily using the TouchPad TOSHIBA Touch and Launch is useful in the following conditions E To open a file located on the desktop whose icon is obscured by a window E To open a page contained in the Internet Explo
14. TOSHIBA does not bear responsibility for the following B Damage to any CD R RW or DVD R RW R RW RAM disc that may be caused by writing or rewriting with this product W Any change or loss of the recorded contents of CD R RW or DVD R RW R RW RAM disc that may be caused by writing or rewriting with this product or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents E Damage that may be caused by using third party equipment or software Given the technological limitations of current optical disc writing drives you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices Also it is a good idea to make two or more copies of important data in case of undesired change or loss of the recorded contents User s Manual 4 11 Operating Basics Before writing or rewriting E Based on TOSHIBA s limited compatibility testing we suggest the following manufacturers of CD R RW and DVD R R RW RW RAM disc However in no event does TOSHIBA guarantee the operation quality or performance of any disc Disc quality can affect write or rewrite success rates i CD R CD RW High Speed CD RW Ultra Speed CD RW DVD R DVD R DVD RW DVD R DL DVD RW DVD RAM TAIYO YUDEN Co Ltd MITSUBISHI Chemical Corporation Ricoh Co Ltd Hitachi Maxell Ltd MITSUBISHI Chemical Corporation
15. enclosed in parentheses following their definition For example Read Only Memory ROM Acronyms are also defined in the Glossary Icons Icons identify ports dials and other parts of your computer The indicator panel also uses icons to identify the components it is providing information on Keys The keyboard keys are used in the text to describe many computer operations A distinctive typeface identifies the key top symbols as they appear on the keyboard For example Enter identifies the Enter key User s Manual xxxi Preface Key operation Some operations require you to simultaneously use two or more keys We identify such operations by the key top symbols separated by a plus sign For example Ctrl C means you must hold down Ctrl and at the same time press C If three keys are used hold down the first two and at the same time press the third ABC When procedures require an action such as clicking an icon or entering text the icon s name or the text you are to type in is represented in the type face you see to the left Display D ABC Names of windows or icons or text generated by lt lt the computer that appears on its display screen is presented in the type face you see to the left Messages Messages are used in this manual to bring important information to your attention Each type of message is identified as shown below JN Pay attention A caution informs you that improper use of equipment or fa
16. 16 9x16 8x8 8x8 9x14 9 x 16 LCD colors 16 of 256K 16 of 256K 16 of 256K 16 of 256K 16 of 256K 16 of 256K 4 of 256K 2 of 256K Mono Mono CRT colors 16 of 256K 16 of 256K 16 of 256K 16 of 256K 16 of 256K 16 of 256K 4 of 256K 2 of 256K Mono Mono Scanning frequency Vertical Hz 70 70 70 70 70 70 70 70 70 70 User s Manual B 2 Display Controller and Modes Table 1 Video modes VGA continued Video Type Resolution Character LCD CRT Scanning mode matrix colors colors frequency pels Vertical Hz D VGA 320 x 200 8x8 16 of 256K 16 of 256K 70 Grph Pels E VGA 640 x 200 8x8 16 of 256K 16 of 256K 70 Grph Pels F VGA 640 x 350 8x14 Mono Mono 70 Grph Pels 10 VGA 640 x 350 8x 14 16 of 256K 16 of 256K 70 Grph Pels 11 VGA 640 x 480 8 x 16 2 of 256K 2 of 256K 60 Grph Pels 12 VGA 640 x 480 8 x 16 16 of 256K 16 of 256K 60 Grph Pels 13 VGA 320 x 200 8x8 256 of 256K 256 of 256K 70 Grph Pels User s Manual B 3 Display Controller and Modes Table 2 Video modes 852GM Resolution LCD colors CRT colors Vertical frequency Hz 640 x 480 256 256K 256 256K 60 75 85 100 800 x 600 256 256K 256 256K 60 75 85 100 1024 x 768 256 256K 256 256K 60 75 85 100 1280 x 1024 256 256K 256 256K 60 Virtual with XGA Panel only 75 85 100 1400 x 1050 256 256K 256 256K 60 Virtual with XGA Panel only 75 85
17. Card The PC Card connector is located on the left side of the computer Windows hot install feature lets you insert PC Cards while the computer s power is on T Wi Do not insert a PC Card while the computer is in standby or T1 Hibernation Mode Some cards might not work properly E A hard disk drives or CD ROM DVD ROM connected to a 16 bit PC Card might affect the performance of the computer s sound system and data transmission including slower transmission speeds and dialing errors To insert a PC Card follow the steps below 1 Insert the PC Card 2 Press gently to ensure a firm connection Inserting the PC Card After inserting the card refer to the card s documentation and check the configuration in Windows to make sure it is appropriate for your card User s Manual 7 2 Optional Devices Removing a PC Card a E Before removing a PC Card make sure that any applications or system T services do not use the card E Be sure to disable the PC Card prior to removing it Otherwise the system may be fatally damaged To remove the PC Card follow the steps below 1 Open the Safely Remove Hardware icon on the Task Bar and disable the PC Card 2 Press the PC Card eject button to extend it 3 Press the extended eject button to pop the card out slightly 4 Grasp the PC Card and draw it out Eject button PC Card Removing the PC Card User s Manual 7 3 Optional Devices Memory expansion
18. Devices and to your monitor s documentation Problem Monitor does not turn on No display Display error occurs Modem Problem Communication software can t initialize modem You can hear a dial tone but can t make a call You place a call but a connection can t be made Procedure Check the software volume settings Make sure the headphone connection is secure If problems persist contact your dealer Procedure Make sure that the external monitor s power Switch is on Confirm that the external monitor s power cable is plugged into a working power outlet Try adjusting the contrast and brightness controls on the external monitor Press hot keys Fn F5 to change the display priority and make sure it is not set for the internal display Check that the cable connecting the external monitor to the computer is attached firmly If problems persist contact your dealer Procedure Make sure the computer s internal modem settings are correct Refer to Phone and Modem Properties in the Control Panel If the call is going through a PBX machine make sure the communication application s tone dial detection feature is disabled You can also use the ATX command Make sure the settings are correct in your communications application User s Manual 8 14 Troubleshooting LAN Problem After making a call you can t hear a ring Communication is cut off unexpectedly A CONNECT display i
19. Intel R 82852 82855 GM GME Graphics Con s Screen resolution olor qualty Fort tg More Highest 32 bit E 1024 by 768 pixele izes gS e this des he primary monito dows desklop onto this mor Identify Troubleshoot Advanced J Display Properties Wi The way to move to multi monitor Wi Press Ctrl Alt F12 keys to display Intel R 82852 82855 GM GME Graphics Controller Prope See the next figure Click in the left of Devices tab See the next figure then select Extended Desktop Wi Check that the Primary Device option is set to Notebook the internal display and the Secondary Device is set to Monitor the external CRT rc 3 Intel R 82852 82855 GM GME Graphics Controller Prope 2 EJ Devices Color Schemes Hot Keys OperGL Information Extended Desktop Settings Device Settings Cancel Apply Intel 82852 82855 GM GME Graphics Controller Properties User s Manual B 8 Display Controller and Modes 2 In some cases DVD video playback images may not be displayed when the display of the computer and a CRT display are used at the same Reduce the resolution use the display of the computer only use the CRT display only or set display device in the multi monitor then play DVD W Please refer to External monitor in Chapter 7 Optional Devices or the application guide for the setting of each display device 3 The DVD
20. Ricoh Co Ltd MITSUBISHI Chemical Corporation Ricoh Co Ltd MITSUBISHI Chemical Corporation DVD Specifications for Recordable disc for General Version2 0 TAIYO YUDEN Co Ltd Matsushita Electric Industrial Co Ltd MITSUBISHI Chemical Corporation Ricoh Co Ltd DVD Specifications for Recordable Disc for Version 1 1 or 1 2 Victor Company of Japan Ltd JVC MITSUBISHI Chemical Corporation MITSUBISHI Chemical Corporation Supporting Double Layer model only MITSUBISHI Chemical Corporation DVD Specifications for DVD RAM Disc for Version2 0 or 2 1 Hitachi Maxell Ltd Matsushita Electric Industrial Co Ltd This drive cannot use discs that allow writing of 8 speeds or more DVD R DVD R or 4 speeds or more DVD RW DVD RW If the disc is poor in quality dirty or damaged writing or rewriting errors may occur Be careful to check the disc for dirt or damage before you use it The actual number of rewrites to CD RW DVD RW DVD RW or DVD RAM is affected by the quality of the disc and the way it is used User s Manual 4 12 Operating Basics There are two types of DVD R discs authoring and general use discs Do not use authoring discs Only general use discs can be written to by a computer drive You can use DVD RAM discs that can be removed from a cartridge and DVD RAM discs designed without a cartridge You can use a disc with a 2 6GB single sided capacity by read only mode Other DVD R
21. TOSHIBA L10 Series computer This powerful notebook computer provides excellent expansion capability including multimedia devices and it is designed to provide years of reliable high performance computing This manual tells how to set up and begin using your TOSHIBA L10 Series computer It also provides detailed information on configuring your computer basic operations and care using optional devices and troubleshooting If you are a new user of computers or if you re new to portable computing first read over the Introduction and The Grand Tour chapters to familiarize yourself with the computer s features components and accessory devices Then read Getting Started for step by step instructions on setting up your computer If you are an experienced computer user please continue reading the preface to learn how this manual is organized then become acquainted with this manual by browsing through its pages Be sure to look over the Specifications section of the Introduction to learn about features that are uncommon or unique to the computer If you are going to install PC Cards or connect external devices such as a monitor be sure to read Chapter 7 Optional Devices Manual contents This manual is composed of the following eight chapters four appendixes a glossary and an index Chapter 1 ntroduction is an overview of the computer s features capabilities and options Chapter 2 The Grand Tour identifies the components of
22. Time Clock battery we recommend that you turn the power status of your computer to ON so that the Real Time Clock battery is charged Refer to Chapter 8 Troubleshooting for details If the following message is displayed on the LCD ERROR 0271 Check date and time settings WARNING 0251 System CMOS checksum bad Default configuration used Press F1 to resume F2 to setup The charge in the RTC battery is getting low or has been exhausted You will need to set the date and time within the BIOS setup using the following steps 1 Press F2 key the BIOS setup screen will be displayed 2 Setthe date in System Date 3 Setthe time in System Time 4 Press F10 key Confirmation message will appear Press Enter key BIOS setup will terminate and the computer will be rebooted F After configuring the date and time it is recommended that you switch the computer on and then leave it in this state so that the Real Time Clock battery can be charged User s Manual 6 4 Power and Power Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack Follow the instructions in this section carefully to ensure safe operation and maximum performance Safety precautions Mishandling of batteries can cause death serious injury or property damage Carefull
23. YUDEN Co Ltd MITSUI Chemicals Inc MITSUBISHI Chemical Corporation Ricoh Co Ltd Hitachi Maxell Ltd CD RW MITSUBISHI Chemical Corporation Ricoh Co Ltd For the special media listed below the following manufacturers are recommended W High Speed CD RW MITSUBISHI Chemical Corporation Ricoh Co Ltd E Ultra Speed CD RW MITSUBISHI Chemical Corporation User s Manual 4 9 Operating Basics TOSHIBA has confirmed the operation of CD R and CD RW media of the manufacturers above Operation of other media cannot be guaranteed E CD RW can generally be rewritten about 1 000 times However the actual number of rewrites is affected by the quality of the media and the way it is used Wi Be sure to connect the AC adaptor when you write or rewrite E Be sure to close all other software programs except the writing software E Do notrun software such as a screen saver which can put a heavy load on the CPU E Operate the computer under the power scheme Always ON Do not use power saving features Wi Do not write while virus check software is running Wait for it to finish then disable virus detection programs including any software that checks files automatically in the background E Do not use hard disk utilities including those intended to enhance HDD access speed They may cause unstable operation and damage data E Write from the computer s HDD to the CD Do not try to write from shared devices such as a LAN s
24. all modes Select a resolution from the menu Security lock Security locks enable you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer The computer has a security lock slot on the left side Attach one end of a cable to a desk and the other end to the security lock slot 1 Turn the computer so the left side faces you 2 Align the holes for the security lock and attach the lock Security lock User s Manual 7 10 TOSHIBA L10 Series Chapter 8 Troubleshooting TOSHIBA designed the computer for durability However should problems occur following the procedures in this chapter can help to determine the cause All readers should become familiar with this chapter Knowing what might go wrong can help prevent problems from occurring Problem solving process Resolving problems will be much easier if you observe the following guidelines B Stop immediately when you recognize a problem exists Further action may result in data loss or damage You may destroy valuable problem related information that can help solve the problem W Observe what is happening Write down what the system is doing and what actions you performed immediately before the problem occurred If you have a printer attached print a copy of the screen using PrtSc The questions and procedures offered in this chapter are meant as a guide they are not definitive problem solving techni
25. approved by Japan Approvals Institute for Telecommunications Equipment Gree A04 0266001 Pursuant to FCC CFR 47 Part 68 When you are ready to install or use the modem call your local telephone company and give them the following information E The telephone number of the line to which you will connect the modem E The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed or if already installed on the bottom of the computer outside of the main system label B The Ringer Equivalence Number REN of the modem which can vary For the REN of your modem refer to your modems label The modem connects to the telephone line by means of a standard jack called the USOC RJ11C Type of service Your modem is designed to be used on standard device telephone lines Connection to telephone company provided coin service central office implemented systems is prohibited Connection to party lines service is subject to state tariffs If you have any questions about your telephone line such as how many pieces of equipment you can connect to it the telephone company will provide this information upon request User s Manual vi TOSHIBA L10 Series Telephone company procedures The goal of the telephone company is to provide you with the best service it can In order to do this it may occasionally be necessary for them t
26. at up to 10 speed DVD R at maximum 8 speed DVD RW at maximum 4 speed DVD R at maximum 8 speed DVD RW at maximum 4 speed and DVD R DL at maximum 2 4speed DVD RAM at maximum 3 speed This drive supports the following formats in addition to DVD RW amp CD R RW drive BH DVD R DVD RW DVD RAM DVD R DVD RW DVD R DL User s Manual 1 5 Introduction Display The computer s LCD panel supports high resolution video graphics The screen can be set at a wide range of viewing angles for maximum comfort and readability Built In Graphics Controller Keyboard Built In Pointing Device Built In TouchPad Ports External Monitor Universal Serial Bus USB 2 0 Slots PC Card 15 0 XGA TFT screen 16 M colors with the following resolution XGA 1024 horizontal x 768 vertical pixels Graphics controller maximizes display performance Refer to Display Controller and Modes section in Appendix B Display Controller and Modes for more information 84 keys or 85 keys compatible with IBM enhanced keyboard embedded numeric overlay dedicated cursor control AN and keys Refer to Chapter 5 The Keyboard for details A TouchPad and control buttons in the palm rest enable control of the on screen pointer and scrolling of windows 15 pin analog VGA port supports VESA DDC2B compatible functions The computer has Universal Serial Bus ports that comply with the USB 2 0 standard which enables
27. below AN arwn gt When handling battery packs do not short circuit the terminals Also do not drop hit or otherwise apply impact do not scratch or break the casing and do not twist or bend the battery pack Do not remove the battery pack while the computer is in Standby Mode Data is stored in RAM so if the computer loses power it will be lost In Hibernation Mode data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed Wait for the Built in HDD indicator to go out Do not touch the latch while holding the computer Or you may get injured by the dropped battery by unintentional release of the latch Save your work Turn the computer s power off Make sure the Power indicator is off Remove all cables connected to the computer Turn the computer upside down Slide and hold the battery release latch 2 to free the battery pack after moving the battery release lock 1 into its unlock position then slide the battery pack out of the computer Battery pack Battery Release Latch 2 1 C gt s ADAQONAANAN Releasing the battery pack 0 Battery Release Lock 1 l For environmental reasons do not throw away a spent battery pack Please return spent battery packs to your TOSHIBA dealer User s Manual 6 11 Power and Power Up Modes Installing the battery pack To install a battery follow the steps below W The battery pack is a lithium
28. cache memory rather than the main memory which saves time The computer has two cache levels Level one is incorporated into the processor and level two resides in external memory capacity The amount of data that can be stored on a magnetic storage device such as a floppy disk or hard disk It is usually described in terms of kilobytes KB where one KB 1024 bytes and megabytes MB where one MB 1024 KB card Synonym for board See board CardBus An industry standard bus for 32 bit PC Cards CD ROM A Compact Disc Read Only Memory is a high capacity disc that can be read from but not written to The CD ROM drive uses a laser rather than magnetic heads to read data from the disc CD R A Compact Disc Recordable disc can be written once and read many times See also CD ROM CD RW A Compact Disc Read Write disc can be rewritten many times See also CD ROM character Any letter number punctuation mark or symbol used by the computer Also synonymous with byte chassis The frame containing the computer chip A small semiconductor containing computer logic and circuitry for processing memory input output functions and controlling other chips CMOS Complementary Metal Oxide Semiconductor An electronic circuit fabricated on a silicon wafer that requires very little power Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable cold start Starting a computer that is currently off
29. click start Control Panel Performance and Maintenance Power Options and Power Meter tab This feature lets you save battery power To specify the power save mode click start Control Panel Performance and Maintenance Power Options At Power schemes tab you can select the mode for Power schemes This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened To specify the setting click start Control Panel Performance and Maintenance Power Options and Advanced tab When battery power is exhausted to the point that computer operation cannot be continued the system automatically enters Hibernation Mode and shuts down To specify the setting click start Control Panel Performance and Maintenance Power Options and Alarms tab This feature lets you turn off the power without exiting from your software The contents of main memory are saved to the hard disk when you turn on the power again you can continue working right where you left off Refer to the Turning off the power section in Chapter 3 Getting Started for details If you have to interrupt your work you can turn off the power without exiting from your software Data is maintained in the computer s main memory When you turn on the power again you can continue working right where you left off User s Manual Introduction Utilities This section describes preinstalled utilities and tells
30. connected to the computer can display up to 1920 horizontal and 1440 vertical pixels at 16 M colors The display controller also controls the video mode which uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed on screen Software written for a given video mode will run on any computer that supports the mode The computer s display controller supports all VGA modes the most widely used industry standards User s Manual Display Controller and Modes Video modes Video mode 0 1 2 3 0 1 2 3 O 1 2 3 4 5 7 The computer supports video modes defined in the tables below If your application offers a selection of mode numbers that do not match the numbers on the table select a mode based on mode type resolution character matrix number of colors and refresh rates Also if your software supports both graphics and text modes the screen display may appear to operate faster using a text mode Table 1 Video modes VGA Type VGA Text VGA Text VGA Text VGA Text VGA Text VGA Text VGA Grph VGA Grph VGA Text VGA Text Resolution Character 40 x 25 Characters 80 x 25 Characters 40 x 25 Characters 80 x 25 Characters 40 x 25 Characters 80 x 25 Characters 320 x 200 Pels 640 x 200 Pels 80 x 25 Characters 80 x 25 Characters matrix pels 8x8 8x8 8x 14 8x14 9 x
31. correctly but others do causing a problem Make sure the hardware not configuration matches your software s needs Check the CD DVD s documentation Check the type of CD DVD you are using The drive supports DVD ROM DVD ROM DVD Videol DVD R DVD RW DVD R DVD RW DVD RAM CD ROM CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CDEXTRA Recordable CD CD R CD RW DVD R DVD RW DVD R DVD RW DVD RAM Check the region code on the DVD It must match that on the DVD Super Multi drive Region codes are listed in the Fixed optical media drives section in Chapter 2 The Grand Tour Floppy disk drive For more information refer to Chapter 4 Operating Basics Problem Procedure Drive does not operate There may be a faulty cable connection Check the connection to the computer and to the drive Some programs run The software or hardware configuration may be correctly but others do causing a problem Make sure the hardware not configuration matches your software needs You cannot access the Try another floppy disk If you can access the external 3 72 floppy floppy disk the original floppy disk not the drive disk drive is probably causing the problem If problems persist contact your dealer User s Manual 8 10 Troubleshooting PC Card Refer also to Chapter 7 Problem PC Card error occurs Pointing device Optional Devices Pro
32. could damage the computer Opening the display User s Manual 3 7 Getting Started Turning on the power This section describes how to turn on the power T After you turn on the power for the first time do not turn it off until you have J set up the operating system Refer to the section Windows XP setup 1 If an optional external floppy disk drive is connected make sure it is empty If a floppy disk is in the drive press the eject button and remove the floppy disk 2 Open the display 3 Press and hold the computer s power button for two or three seconds Turning on the power Windows XP setup When you first turn on the power the computer s initial screen is the Microsoft Windows XP Home Edition or Professional Edition Startup Screen Logo Follow the on screen directions F Be sure to read the Windows End User License Agreement display carefully User s Manual 3 8 Getting Started Turning off the power The power can be turned off in one of the following modes Shut down Boot Hibernation or Standby Mode Shut Down mode Boot mode AN A When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system s main screen 1 If you have entered data save it to the hard disk or to a floppy disk drive 2 Make sure all disk disc activity has stopped then remove the CD DVDs or floppy disk drive Make sure the Buil
33. disc that was made with other software on a different DVD R RW or DVD R RW recorder If you add data to a DVD R and DVD R disc that you have already recorded to you might not be able to read the added data under some circumstances It cannot be read in 16 bit operating systems such as Windows 98SE and Windows ME In Windows NT4 you will need Service Pack 6 or later to read added data In Windows 2000 you will need Service Pack 2 or later to read it Some DVD ROM and DVD ROM amp CD R RW drives cannot read added data regardless of the operating system RecordNow does not support recording to DVD RAM discs To record to a DVD RAM use Explorer or other utility When you back up a DVD disc be sure the source drive supports recording to DVD R RW or DVD R RW discs If the source drive does not support recording to DVD R RW or DVD R RW discs it might not be backed up correctly When you back up a DVD R DVD RW DVD R or DVD RW be sure to use the same type of disc You cannot partially delete any data written to a CD RW DVD RW or DVD RW disc Data written to a CD R DVD R DVD R disc cannot be deleted either in whole or in part User s Manual 4 15 Operating Basics Data Verification To verify that data is written or rewritten correctly follow the steps below before you write or rewrite a data CD DVD 1 Click the Options button on the RecordNow Console to open the Options panels 2 Select the Dat
34. from overheating JN Do not block the cooling vents Also ensure that foreign objects are kept out of the vents as items such as pins or similar objects which can damage the computer s circuitry ot Universal Serial Bus A pair of Universal Serial Bus ports is on the left USB 2 0 ports side The port complies with the USB 2 0 standard which enables data transfer speeds 40 times faster than the USB 1 1 standard The ports also support USB 1 1 Keep foreign objects out of the USB connectors A pin or similar object can damage the computer s circuitry Operation of all functions of all USB devices has not been confirmed As such some untested third party devices may not function properly Q Microphone Jack A 3 5 mm mini microphone jack enables connection of a three conductor mini jack for monaural microphone input CY Headphone Jack This jack outputs analog audio signals 3 l a PC Card Slot A PC Card slot can accommodate a 5 mm Type Il card The slot supports 16 bit PC Cards and CardBus PC Cards User s Manual 2 2 The Grand Tour Right side The following figure shows the computer s right side ODD Indicator emergeny Eject Hol Fixed Optical Media Disc Drive Eject Button Emergency Eject Button ODD Indicator Pr Eject Button Fixed Optical Media Disc Drive The right side of the computer The computer is configured with a full size optical media drive module tha
35. how to start them For details on operations refer to each utility s online manual help files or readme txt files a Please note that the descriptions for starting some Utilities are based on setting the Control Panel to Category View On Classic view the description is different TOSHIBA Console TOSHIBA Console is a graphical user interface that provides easy access to help and services HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use To start the utility click the start and click Control Panel In the Control Panel Printers and Other Hardware select the TOSHIBA HW Setup icon DVD Video Player The DVD Video Player is used to play DVD Video It has an on screen interface and functions Click start point to All Programs point to InterVideo WinDVD then click InterVideo WinDVD TOSHIBA Zooming This utility allows you to enlarge or reduce the Utility icon size on the desktop or the application window To run TOSHIBA Zooming Utility click start select All Programs followed by TOSHIBA followed by Utilities and then click Zooming Utility RecordNow Basic You can create CD DVDs in several formats for TOSHIBA including audio CDs that can be played on a standard stereo CD player and data CDs to store the files and folders on your hard disk drive This software can be used on a model with the DVD ROM amp CD R RW drive and the DVD
36. left contro button and move the cursor to drag the item you want to move 2 Lift your finger to drop the item where you want it Scroll Vertical Move your finger up or down the right edge of the TouchPad Horizontal Move your finger left or right along the bottom edge of the TouchPad Using the USB floppy disk drive An optional 3 72 floppy disk drive connects to the computer s USB port It accommodates 1 44 megabyte or 720 kilobyte floppy disks Refer to Chapter 2 The Grand Tour for more information Connecting 3 77 floppy disk drive To connect the drive plug the floppy disk drive connector into a USB port Refer to the following figure Make sure the connector is right side up and properly aligned with the socket Do not try to force the connection doing so can damage the connecting pins Connecting the USB floppy disk drive a If you connect the floppy disk drive after turning on the computer it will take j about 10 seconds for the computer to recognize the drive Do not disconnect and reconnect before 10 seconds have elapsed User s Manual 4 2 Operating Basics Disconnecting 3 1 2 floppy disk drive When you have finished using the floppy disk drive follow the procedures below to disconnect it 1 Wait for the indicator light to go out to make sure all floppy disk activity has stopped JN If you disconnect the floppy disk drive or turn off the power while the computer is accessing the drive
37. set the computer to Hibernation Mode or save your data and shut down the computer Do not change the battery pack while the AC adaptor is connected Battery pack To ensure that the battery pack maintains its maximum capacity operate the computer on battery power at least once a month until the battery pack is fully discharged Refer to Extending battery life in this chapter for procedures If the computer is continuously operated on AC power through an AC adaptor for an extended period more than a month the battery may fail to retain a charge It may not function efficiently over the expected life of the battery and the Battery indicator may not indicate a low battery condition User s Manual 6 3 Power and Power Up Modes Real Time Clock battery The Real Time Clock RTC battery provides power for the internal real time clock and calendar It also maintains the system configuration If the RTC battery becomes completely discharged the system loses this data and the real time clock and calendar stop working The computer s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative The battery can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations F E You can change the settings of the Real Time Clock by pressing F2 in j POST W After configuring the time and date for the Real
38. specific internal or peripheral device e g keyboard controller co processor A circuit built into the processor that is dedicated to intensive math calculations CPS Characters Per Second Typically used to indicate the transmission speed of a printer CPU Central Processing Unit The portion of the computer that interprets and executes instructions CRT Cathode Ray Tube A vacuum tube in which beams projected on a fluorescent screen producing luminous spots An example is the television set cursor A small blinking rectangle or line that indicates the current position on the display screen D data Information that is factual measurable or statistical that a computer can process store or retrieve data bits A data communications parameter controlling the number of bits binary digits used to make up a byte If data bits 7 the computer can generate 128 unique characters If data bits 8 the computer can generate 256 unique characters DC Direct Current Electric current that flows in one direction This type of power is usually supplied by batteries default The parameter value automatically selected by the system when you or the program do not provide instructions Also called a preset value delete To remove data from a disk or other data storage device Synonymous with erase device driver A program that controls communication between a specific peripheral device and the computer The CONFIG SYS file contains d
39. transmission the date and time it is sent and an identification of the business other entity or individual sending the message and the telephone number of the sending machine or such business other entity or individual In order to program this information into your fax modem you should complete the setup of your fax software before sending messages User s Manual vii TOSHIBA L10 Series Instructions for IC CS 03 certified equipment 1 The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipm
40. turning on the power COM COM2 COM3 and COMA The names assigned to the serial and communication ports commands Instructions you enter at the terminal keyboard that direct the actions of the computer or its peripheral devices communications The means by which a computer transmits and receives data to and from another computer or device See parallel interface serial interface compatibility 1 The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred 2 the ability of one device to connect to or communicate with another system or component components Elements or parts of a system which make up the whole system User s Manual Glossary 4 Glossary computer program A set of instructions written for a computer that enable it to achieve a desired result computer system A combination of hardware software firmware and peripheral components assembled to process data into useful information configuration The specific components in your system such as the terminal printer and disk drives and the settings that define how your system works You use the HW Setup program to control your system configuration control keys A key or sequence of keys you enter from the keyboard to initiate a particular function within a program controller Built in hardware and software that controls the functions of a
41. use to store programs and data but you cannot use to start the computer See system disk nonvolatile memory Memory usually read only ROM that is capable of permanently storing information Turning the computer s power off does not alter data stored in nonvolatile memory numeric keypad overlay A feature that allows you to use certain keys on the keyboard to perform numeric entry or to control cursor and page movement Oo OCR Optical Character Recognition reader A technique or device that uses laser or visible light to identify characters and input them into a storage device online state A functional state of a peripheral device when it is ready to receive or transmit data User s Manual Glossary 9 Glossary operating system A group of programs that controls the basic operation of a computer Operating system functions include interpreting programs creating data files and controlling the transmission and receipt input output of data to and from memory and peripheral devices output The results of a computer operation Output commonly indicates data 1 printed on paper 2 displayed at a terminal 3 sent through the serial port of internal modem or 4 stored on some magnetic media P parity 1 The symmetrical relationship between two parameter values integers both of which are either on or off odd or even 0 or 1 2 In serial communications an error detection bit that is added to a group of d
42. video overlay is not displayed when the display mode of CRT display is set to high resolution and high refresh rate mode Please decrease the resolution and refresh rate of CRT display 4 When the display mode is TV or simultaneous LCD internal liquid crystal display TV and the system goes into Standby or Hibernation Mode you can switch to the LCD internal liquid crystal display display mode by pressing Fn F5 Under this environment however you may not return to the TV or simultaneous LCD internal liquid crystal display TV display mode In these cases perform the following steps Press Ctrl Alt F12 to select Intel R 82852 82855 GM GME Graphics Controller Prope Then click the icon indicating a display device display mode you want to use in the left pane of the Devices tab 5 When the LCD internal liquid crystal display display mode is selected the Virtual Virtual Screen display mode can be set However afterwards it may not possible to change the screen resolution to more than 1280 x 1024 pixels in Highest 32bit mode for example when you attempt to set the resolution to 1600 x 1200 using the Screen resolution slide bar and then select Highest 32bit mode from the Color quality drop down menu In these cases perform the steps below First use the Screen resolution slide bar to select the 1024 x 768 resolution and then change the resolution to more than 1280 x 1024 and select Highest 32bit from the
43. you may lose data or damage the floppy disk or the drive 2 Click the Safely Remove Hardware icon on the Task Bar 3 Click floppy disk drive 4 Pull the floppy disk drive connector out of the USB port Using the optical media drive The text and illustrations in this section refer primarily to the optical DVD ROM drive However operation is the same for all other optical media drives The full size drive provides high performance execution of CD DVD ROM based programs You can run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without an adaptor An ATAPI interface controller is used for CD DVD ROM operation When the computer is accessing a CD DVD ROM an indicator on the drive glows 1 Use the WinDVD application to view DVD movie discs If you have a DVD ROM and CD R RW drive refer also to the Writing CDs with the DVD ROM and CD R RW drive section for precautions on writing to CDs DVDs If you have a DVD Super Multi drive refer also to the Writing CD DVDs with the DVD Super Multi drive section for precautions on writing to CDs DVDs If you have a DVD Super Multi drive Supporting Double Layer refer also to the Writing CD DVDs with the DVD Super Multi drive section for precautions on writing to CDs DVDs User s Manual 4 3 Operating Basics Loading discs To load a disc follow the steps below and refer to the figures 1 a When the power is on press the DVD ROM eject button to open the drawer slightly Eject
44. 0 0 cece eee eee 8 3 System start up se cee See eee eae RACER Ree 8 3 SII CIR Eee 8 4 POWER c LliIledgesedwee dene e e ee ERES QUE Pu xe qui 8 4 Real Time Clock e isses seem RR mmn 8 6 Keyboard i bls aene Neal de Pabedan E 8 7 LCDpanel 2 iuacue Rc em RR REG ERE 8 7 Hard disk drive ec cece eee edle Rr 8 7 DVD ROM amp CD R RW drive 0 2 eee 8 8 DVD Super Multi drive and DVD Super Multi drive Supporting Double layer s crave totes cupidus Sia a dide HIRE A Sate E 8 9 Floppy disk drive 2 eee 8 10 PC Card t ee kc eh Gee DESEE RI eee 8 11 Pointing device 0 00 eee 8 11 USB oet ret rv eet dn ga Ga E E E 8 13 Memory expansion 00 00 eee II 8 13 Sound system 8 14 MonltOF i uceiiecanbesedekeRxidaesdgxeenisdued egg ees 8 14 MOGI 25 pisi teleen dines sgkundeawg EUNDEM 8 14 PAN bec he both Weta bbwidd e Eee RIb JEEP BIERRBRS EEG 8 15 Wireless LAN 0 cee ee cee pe eee rer 8 15 Printer zie Lesereseikee he ihe ae eda Nene aie Rede Neq xs 8 16 TOSHIBA support 25 22 o pp a EEG ERE E RE 8 16 Before you call sese lu RR RE n 8 16 Where to write lcleeleeeeee IRI 8 16 User s Manual xxviii Table of Contents Appendix A Appendix B Appendix C Appendix D Specifications Display Controller and Modes Wireless LAN AC Power Cord and Connectors Glossary Index User s Manual xxix TOSHIBA L10 Series Preface Congratulations on your purchase of the
45. 1 Click start point to All Programs point to Accessories point to Entertainment and click Volume Control Click Options and point to Properties Select Recording and click OK Click Options and select Advanced Controls Click Advanced Check the Microphone Boost checkbox oak wn Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack F The internal modem does not support voice functions All data and fax functions are supported N E ncase of a lightning storm unplug the modem cable from the telephone jack W Do not connect the modem to a digital telephone line A digital line will damage the modem User s Manual 4 20 Operating Basics Region selection J Telecommunication regulations vary from one region to another so you will need to make sure the internal modem s settings are correct for the region in which it will be used To select a region follow the steps below 1 Click start point to All Programs TOSHIBA Networking and click Modem Region Select Do not use the Country Region Select function in the Modem setup utility in the Control Panel if the function is available If you change the Country Region in the Control Panel the change may not take effect 2 The Region Selection icon will appear in the Task Bar Click the icon with the primary mouse button to display a list of regions that the modem supports A sub menu for teleph
46. 25 disconnecting 4 25 M Media care 4 19 CD DVDs 4 19 floppy disks 4 19 Memory 1 3 expansion 1 13 7 4 installing 7 5 removing 7 6 Modem 1 7 4 20 connecting 4 22 disconnecting 4 23 properties menu 4 21 region selection 4 21 Monitor external 1 6 7 8 Moving the computer 4 26 P PC card 1 6 7 2 inserting 7 2 location of slot 2 2 removing 7 3 Ports 1 6 external monitor 1 6 USB 1 6 Power button location 2 6 conditions 6 1 hibernation mode 3 9 indicator 6 2 panel power on off 1 10 6 13 shut Down mode Boot mode 3 9 standby mode 3 11 system Auto Off 6 13 turning off 3 9 turning on 3 8 Power up modes 6 13 Problems AC power 8 5 analyzing 8 2 Battery 8 5 CD RW DVD ROM drive User s Manual Index 2 Index 8 8 DVD Super Multi drive 8 9 Floppy disk drive 8 10 Hard disk drive 8 7 Hardware and system checklist 8 3 Keyboard 8 7 LAN 8 15 LCD panel 8 7 Memory expansion 8 13 Modem 8 14 Monitor 8 14 overheating power down 8 4 PC card 8 11 Pointing device 8 11 Power 8 4 Real Time Clock 8 6 Self test 8 4 Sound system 8 14 Support from TOSHIBA 8 16 System start up 8 3 USB 8 13 Wireless LAN 8 15 Processor 1 3 R Restarting the computer 3 12 S Security lock attaching 7 10 Soft keys emulating keys on enhanced keyboard 5 2 ScrLock 5 4 Sonic RecordNow 1 11 4 15 Sound System 1 7 4 20 headphone jack 1 7 microphone jack 1
47. 3 CD RW DVD ROM drive 1 4 location 2 3 using 4 3 writing 4 9 Cleaning the computer 4 25 D Display 1 6 automatic power off 1 9 brightness decreases 5 4 brightness increases 5 4 controller 1 6 opening 3 7 Display controller B 1 Documentation list 1 2 DVD Super Multi drive 1 5 location 2 3 using 4 3 writing 4 11 DVD ROM amp CD R RW drive 1 4 location 2 3 using 4 3 Environment 3 2 Equipment checklist 1 1 Equipment setup general conditions 3 2 placement 3 3 Ergonomics lighting 3 4 seating and posture 3 3 work habits 3 4 E Floppy disk 1 4 using 4 2 Index 1 Index Fn Esc sound mute 5 3 Fn F1 instant security 5 3 Fn F2 power save mode 5 3 Fn F3 standby 5 3 Fn F4 hibernation 5 3 Fn F5 display selection 5 3 Fn F6 Display Brightness de creases 5 4 Fn F7 Display Brightness in creases 5 4 Fn F8 Wireless setting 5 4 Fn F9 Touch Pad 5 4 Fn Sticky key 5 5 Function keys 5 2 G Graphics controller 1 6 Hard disk drive 1 4 automatic power off 1 9 Hibernation 1 10 5 3 HW Setup 1 11 K Keyboard 1 6 5 1 emulating keys on enhanced 5 2 F1 F12 function keys 5 2 hot keys 5 3 typewriter keys 5 1 Windows special keys 5 6 Keypad overlay 1 9 5 6 numeric mode 5 6 temporarily using normal keyboard overlay on 5 7 turning on the overlays 5 6 L LAN 1 8 4 24 cable types 4 24 connecting 4
48. 5 CD DVDs without using an adaptor 1 The read speed is slower at the center of a disc and faster at the outer edge DVD read 8 speed maximum DVD R write 8 speed maximum DVD RW write 4 speed maximum DVD R write 8 speed maximum DVD RW write 4 speed maximum DVD RAM write 3 speed maximum CD read 24 speed maximum CD R write 24 speed maximum CD RW write 10 speed maximum Ultra speed media DVD Super Multi drive Supporting Double Layer The full size DVD Super Multi drive module lets you record data to rewritable CD DVDs as well as run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without using an adaptor 1 The read speed is slower at the center of a disc and faster at the outer edge DVD read 8 speed maximum DVD R write 8 speed maximum DVD RW write 4 speed maximum DVD R write 8 speed maximum DVD RW write 4 speed maximum DVD R DL write 2 4 speed maximum DVD RAM write 3 speed maximum CD read 24 speed maximum CD R write 24 speed maximum CD RW write 10 speed maximum Ultra speed media User s Manual 2 12 The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz enabling you to use the computer in almost any country region To recharge the battery simply connect the AC adaptor to a power sour
49. 5 Disconnecting LAN cable 0022000 cee eeeeee 4 25 Cleaning the computer 2 0200 eee eee eee eee 4 25 Moving the computer 22200 eee eee eee 4 26 User s Manual xxvi Table of Contents Chapter 5 Chapter 6 The Keyboard Typewriter keyS 0 0022 e eee eee 5 1 F1 F12 function Keys oer ok ex etn 5 2 Soft keys Fn key combinations llll lsssss 5 2 Emulating keys on enhanced keyboard 22 5 2 Hot Keys s wneud ERI eere ede Loh indies E 5 3 F Sticky c P T 5 5 Windows special keys 200 e eee eee eee 5 6 Keypad OVEN AY aine ikani naya aim Ged wel eae E Eds 5 6 Turning on the overlayS 0 0 0 cece eee 5 6 Temporarily using normal keyboard overlay on 5 7 Generating ASCII characters 0 000 eee eee eee 5 7 Power and Power Up Modes Power conditions 2 26206 660 ecgee eee n rr err ee ee 6 1 Power indicator 0 0 fetes 6 2 Battery types cos sive sie we ede br Re CHR RR a RUR ee Rae ot 6 3 Battery Pack xr blest nls ate pie Sala eA Roe ISTE 6 3 Real Time Clock battery 0 00000 e eee eee 6 4 Care and use of the battery pack 20002 2c eeeee 6 5 Safety precautions 0 0 liess 6 5 Charging the batteries 0 000000 6 7 Monitoring battery capacity 0 0 0 cece eee 6 9 Maximizing battery operating time 005 6 9 Retaining data with po
50. 5GME continued Resolution LCD colors CRT colors Vertical frequency Hz 1920X1440 64 64K 64 64K 60 Virtual 75 85 2048X1536 64 64K 64 64K 60 Virtual 75 Table 2 Video modes 852GM continued Resolution LCD colors CRT colors Vertical frequency Hz 640 x 480 16M 16M 16M 16M 60 75 85 100 800 x 600 16M 16M 16M 16M 60 75 85 100 1024 x 768 16M 16M 16M 16M 60 75 85 100 1280 x 1024 16M 16M 16M 16M 60 Virtual with XGA Panel only 75 85 100 User s Manual B 6 Display Controller and Modes Table 2 Video modes 852GM continued 1400 x 1050 16M 16M 16M 16M 60 Virtual with XGA Panel only 75 85 1600 x 1200 16M 16M 16M 16M 60 Virtual 75 85 Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode 1 Some models in this series are equipped with an 855GME display chipset User s Manual B 7 Display Controller and Modes Display Settings 1 You cannot move from the Settings tab of Display Properties to the multi monitor when you are using the display of the computer and an external CRT display at the same time E The Settings tab is displayed in the following steps W Open Control Panel click Appearance and Themes W Click Display W Select Settings tab Display Properties Themes Desktop Screen Saver Appearance Settings Drag the monitor icons to match the physical arrangement of your morilors Display 1 Multiple Moritors on
51. 6 or 512 MB memory modules can be installed in the memory slot for a maximum of 1 GB system memory total g Before you install a new 512 MB memory module be sure to remove any l memory modules already installed Video RAM Maximum 64 MB of RAM is provided for video display Power Battery Pack Your computer is powered by a rechargeable lithium ion battery pack 4300mAh User s Manual 1 3 Introduction it RTC Battery AC Adaptor Disks Hard Disk Drive USB floppy disk drive Optional The internal RTC battery backs up the Real Time Clock and calendar The universal AC adaptor provides power to the system and recharges the batteries when they are low It comes with a detachable power cord Because it is universal it can receive a range of AC voltage from 100 to 240 volts however the output current varies among different models Using the wrong model can damage your computer Refer to the AC adaptor section in Chapter 2 The Grand Tour Available in two sizes W 40 0 billion bytes 37 26 GB W 60 0 billion bytes 55 88 GB Other hard disk drives may introduced in the future Accommodates either 3 72 1 44 megabyte or 720 kilobyte floppy disks It connects to a USB port Computers in this series can be configured with a fixed optical media drive The available optical media drives are described below DVD ROM amp CD R RW drive Some models are equipped with a full size DVD ROM amp CD
52. 7 mute hot keys 5 3 Standby 1 10 setting 3 11 System automatic 1 10 T TOSHIBA ConfigFree 1 12 TOSHIBA PC DiagnosticTool 1 12 TOSHIBA Utilities 1 8 TOSHIBA Zooming Utility 1 11 Touch Pad 1 6 location 2 6 using 4 1 TV 7 9 U USB 1 6 location 2 2 2 4 V Video modes B 2 Video RAM 1 3 W Wireless communication switch 4 23 indicator 4 24 Wireless LAN 1 8 using 4 23 User s Manual Index 3 Index User s Manual Index 4
53. 8 16 and so on For example the binary number 101 has a value of 5 See also ASCII BIOS Basic Input Output System The firmware that controls data flow within the computer See also firmware bit Derived from binary digit the basic unit of information used by the computer It is either zero or one Eight bits is one byte See also byte board A circuit board An internal card containing electronic components called chips which perform a specific function or increase the capabilities of the system boot Short for bootstrap A program that starts or restarts the computer The program reads instructions from a storage device into the computer s memory bps Bits per second Typically used to describe the data transmission speed of a modem buffer The portion of the computer s memory where data is temporarily stored Buffers often compensate for differences in the rate of flow from one device to another bus An interface for transmission of signals data or electric power byte The representation of a single character A sequence of eight bits treated as a single unit also the smallest addressable unit within the system User s Manual Glossary 3 Glossary C cache memory High speed memory which stores data that increases processor speed and data transfer rate When the CPU reads data from main memory it stores a copy of this data in cache memory The next time the CPU needs that same data it looks for it in the
54. A as replacements Always make sure the battery pack is installed correctly and securely Otherwise a battery pack could fall out and possibly cause injury Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius Otherwise the electrolyte solution might leak battery pack performance might deteriorate and the battery life might be shortened User s Manual 6 6 Power and Power Up Modes 6 Be sure to monitor the remaining battery power If the battery pack and real time clock battery discharge completely Standby and Suspend will not function and data in memory will be lost Also the computer might register an incorrect time and date In this case connect the AC adaptor to recharge the batteries 7 Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor Never remove the battery pack while the computer is in Suspend or Standby Mode Data will be lost Note 1 Never remove the battery pack while the Wake up on LAN function is enabled Data will be lost Before you remove a battery pack disable the Wake up on LAN function 2 After the battery pack is charged avoid leaving the AC adaptor connected and the computer turned off for more than a few hours at a time Continuing to charge a fully charged battery pack can damage the battery Charging the batteries When the power in the battery pack becomes low the Battery indicator flash
55. AN 1 You can install additional memory in the computer s memory module socket to increase the amount of RAM This section describes how to install and remove a memory module m Use only memory modules approved by TOSHIBA E Do not try to install or remove a memory module under the following conditions You can damage the computer and the module Also data will be lost a The computer is turned on b The computer was shut down using the Standby Mode or Hibernation Mode Wi The beep sound rings when incorrect memory is inserted Refer to Memory expansion section in Chapter 8 Troubleshooting for details E Expansion memory is a precision electronic component that may be fatally damaged by static electricity Since human body has slight static electricity be sure to discharge static electricity from your body before installing an expansion memory module To discharge your body s static electricity simply touch any metal close to you with bare hands Use a point size 1 Phillips screwdriver to remove and fasten the screws Use of an incorrect screwdriver can damage the screw heads User s Manual 7 4 Optional Devices Installing a memory module Follow the steps below to install a memory module 1 Set the computer to boot mode and turn off the power 2 Remove all cables connected to the computer 3 Turn the computer upside down and remove the battery pack refer to Chapter 6 Power and Power Up Modes 4 Lo
56. Button Pressing the DVD ROM eject button b Pressing the eject button will not open the drawer when the disc drive s power is off If the power is off you can open the drawer by inserting a slender object about 15 mm such as a straightened paper clip into the eject hole just to the right of the eject button Diameter 1 0mm Manual release with the eject hole User s Manual 4 4 Operating Basics 2 Grasp the drawer gently and pull until it is fully opened Pulling the drawer open 3 Place the disc label side up in the drawer Inserting a disc e i When the drawer is fully opened the edge of the computer will extend T slightly over the disc tray Therefore you will need to turn the disc at an angle when you place it in the tray After seating the disc however make sure it lies flat as shown in the figure above AN E Do not touch the laser lens Doing so could cause misalignment W Keep foreign matter from entering the drive Check the back edge of the tray to make sure it carries no debris before closing the drive User s Manual 4 5 Operating Basics 4 Press gently at the center of the disc until you feel it click into place The disc should lie below the top of the spindle flush with the spindle base 5 Push the center of the drawer to close it Press gently until it locks into place fthe CD DVD is not seated properly when the drawer is closed the disc might be damaged Als
57. Color quality drop down menu User s Manual B 9 TOSHIBA L10 Series Appendix C Wireless LAN Card Specifications Form Factor Mini PCI Typelll Compatibility W IEEE 802 11 Standard for Wireless LANs W Wi Fi Wireless Fidelity certified by the Wi Fi Alliance The Wi Fi CERTIFIED logo is a certification mark of the Wi Fi Alliance Microsoft Windows Networking Media Access Protocol CSMA CA Collision Avoidance with Data Rate Acknowledgement ACK E 54 48 36 24 18 12 9 6 Mb s IEEE 802 119 Wi 11 5 5 2 1 Mb s IEEE 802 11b Network Operating System 1 The Wireless LAN feature is not available on all models User s Manual Wireless LAN Radio Characteristics T Radio Characteristics of Wireless LAN Cards may vary according to E Country region where the product was purchased E Type of product Wireless communication is often subject to local radio regulations Although Wireless LAN wireless networking products have been designed for operation in the license free 2 4GHz band local radio regulations may impose a number of limitations to the use of wireless communication equipment Refer to the sheet Information to the User for regulatory information that may apply in your country region R F Frequency B Band2 4GHz 2400 2483 5 MHz Modulation B DSSS CCK DSSS DQPSK DSSS DBPSK Technique IEEE 802 11b B OFDM BPSK OFDM QPSK OFDM 16QAM OFDM 64QAM IEEE 802 119 The range of the wireless s
58. DIATION EXPOSURE VORSICHT DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFUHREN VON ANDEREN VORGANGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KONNEN GEFAHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN User s Manual xvii TOSHIBA L10 Series General Precautions TOSHIBA computers are designed to optimize safety minimize strain and withstand the rigors of portability However certain precautions should be observed to further reduce the risk of personal injury or damage to the computer Be certain to read the general precautions below and to note the cautions included in the text of the manual Please also refer to the Safety Instruction Manual Stress injury Carefully read the Safety Instruction Manual It contains information on the prevention of stress injuries to your hands and wrists than can be caused by extensive keyboard use Chapter 3 Getting Started also includes information on workspace design posture and lighting that can help reduce physical stress Heat warning E Avoid prolonged physical contact with the computer If the computer is used for long periods its surface can become very warm While the temperature will not feel hot to the touch if you maintain physical contact with the computer for a long time if you rest the computer on your lap or if you keep your hands on the palm rest for example your skin might suffer low heat injury E ifthe computer has been used fo
59. Dieses Ger t enth lt ein Laser System und ist als LASERSCHUTZKLASSE 1 PRODUKT klassifiziert F r den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgf ltig durch und bewahren diese bitte als Referenz auf Falls Probleme mit diesem Modell auftreten benachrichtigen Sie bitte die nachste autorisierte Service Vertretung Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Ger t nicht ge ffnet werden ADVARSEL Denne maerking er anbragt udvendigt pa apparatet og indikerer at apparatet arbejder med laserstr ler af klasse 1 hviket betyder at der anvendes laserstrlier af svageste klasse og at man ikke pa apparatets yderside kan bilve udsat for utilladellg kraftig str ling APPARATET BOR KUN ABNES AF FAGFOLK MED SAERLIGT KENDSKAB TIL APPARATER MED LASERSTRALER Indvendigt i apparatet er anbragt den her gengivne advarselsmeekning som advarer imod at foretage sadanne indgreb i apparatet at man kan komme til at udsatte sig for laserstraling User s Manual xvi TOSHIBA L10 Series OBS Apparaten innehaller laserkomponent som avger laserstraining verstigande gr nsen for laserklass 1 VAROITUS Suojakoteloa si saa avata Laite sisaltaa laserdiodin joka lahetaa n kym t nt silmilie vaarallista lasers teily CAUTION USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER S MANUAL MAY RESULT IN HAZARDOUS RA
60. IBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non approved working environments before use In the case of automobiles or aircraft the manufacturer or airline respectively should be asked for permission before use of this product Furthermore for general safety reasons the use of this product in environments with explosive atmospheres is not permitted User s Manual XX General Precautions Network connection Class A warning If this product has networking capabilities and will be connected to a network Class A radiation limits will be observed in accordance with technical conventions This means that if the product will be used in a domestic environment other devices in the near surrounding area may suffer interference Consequently please do not use this product in such environments for example a living room otherwise you could be held responsible for any ensuing interference Information on the secure writing of optical media Even if your software gives no indication that any problems have occurred you should always check to ensure that information has been successfully stored on recordable optical media CD R CD RW and so forth Wireless LAN and your Health Wireless LAN products like other radio devices emit radio frequency electromagnetic energy The level of energy emitted by Wireless LAN devices however is far less than the electromagnetic
61. OM drives for computers or other DVD players may not be able to read DVD R RW or DVD R RW discs Data written to a CD R DVD R DVD R disc cannot be deleted either in whole or in part Data deleted erased from a CD RW DVD RW DVD RW and DVD RAM disc cannot be recovered Check the content of the disc carefully before you delete it If multiple drives that can write data to discs are connected be careful not to delete data from the wrong drive In writing to a DVD R RW DVD R RW or DVD RAM disc some disc space is required for file management so you may not be able to write the full capacity of the disc Since the disc is based on the DVD standard it might be filled with dummy data if the written data is less than about 1 GB Even if you write only a small amount of data it might take time to fill in the dummy data DVD RAM formatted by FAT32 cannot be read in Windows 2000 without DVD RAM Driver Software When multiple drives that can write data to discs are connected be careful not to write to the wrong drive Be sure to connect the AC adaptor before you write or rewrite Before you enter Standby Hibernation Mode be sure to finish DVD RAM writing Writing is finished if you can eject DVD RAM media Be sure to close all other software programs except the writing software Do not run software such as a screen saver which can put a heavy load on the CPU Operate the computer under the power scheme Always ON Do not use power savin
62. PC Card to which the battery supplies power Enabling Standby Mode conserves battery power if you are frequently turning the computer off and on Where you store your programs and data Closing the display when you are not using the keyboard saves power Operating time decreases at low temperatures The condition of the battery terminals Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the battery pack User s Manual 6 9 Power and Power Up Modes Retaining data with power off When you turn off your computer with fully charged batteries the batteries retain data for the following approximate time periods Battery pack 4300 mAh About 3 days Standby Mode About 30 days Boot mode RTC battery 30 days Extending battery life To maximize the life of your battery pack B Atleast once a month disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges Before doing so follow the steps below 1 Turn off the computer s power 2 Disconnect the AC adaptor and turn on the computer s power If it does not turn on go to step 4 3 Operate the computer on battery power for five minutes If the battery pack has at least five minutes of operating time continue operating until the battery pack is fully discharged If the Battery indicator flashes or there is some other warning to indicate a low battery go to step 4
63. Properties click Device tab and the Television icon 5 Change the Settings which are suitable for your TV and suitable according to the region you are 6 Click Apply and or OK at Intel 82852 82855 GM GME Graphics Controller Property W LCD TV Mode Dual Display Clone Extended Desktop 1 Click start and click Control Panel then Appearance and Themes 2 Double click the Display icon to open the Display Properties window 3 Click the Settings tab and click the Advanced button 4 Click Intel Extreme Graphics2 for Mobile click Graphics Properties click Device tab and the Intel R Dual Display Clone icon or Extended Desktop icon 5 Click Device Settings 6 Change the Settings which are suitable for your TV and suitable according to the region you are and click OK at Device Settings 7 Click Apply and or OK at Inte 82852 82855 GM GME Graphics Controller Property E There are 10 Video standard types in the list Select one of the Video Standard types according the region you are W NTSC M for the United States B NTSC J for Japan W PAL B for Europe User s Manual 7 9 Optional Devices Changing the resolution If you want to change the resolution follow the steps below 1 Oi cO Click start and click Control Panel then Appearance and Themes Double click the Display icon to open the Display Properties window Select the Settings tab and click Advanced Select the Adapter tab then select List
64. R RW drive module that lets you run CD DVDs without using an adaptor It reads DVD ROMs at maximum 8 speed and CD ROMs at maximum 24 speed It writes CD R at up to 24 speed and CD RW at up to 24 speed This drive supports the following formats B CD R CD RW DVD ROM DVD Video CD DA CD Text Photo CD Single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form 2 Enhanced CD CD EXTRA User s Manual Introduction DVD Super Multi drive DVD Super Multi drive Supporting Double Layer Some models are equipped with a full size DVD Super Multi drive module that lets you record data to rewritable CD DVDs as well as run either 12cm 4 72 or 8cm 3 15 CD DVDs without using an adaptor It reads DVD ROMs at maximum 8 speed and CD ROMs at maximum 24 speed It writes CD R at up to 24 speed CD RW at up to 10 speed DVD R at maximum 8 speed DVD RW at maximum 4 speed DVD R at maximum 8 speed and DVD RW at maximum 4 speed DVD RAM at maximum 3 speed This drive supports the following formats in addition to DVD RW amp CD R RW drive B DVD R B DVD RW B DVD RAM B DVD R B DVD RW Some models are equipped with a full size DVD Super Multi drive module that lets you record data to rewritable CD DVDs as well as run either 12cm 4 72 or 8cm 3 15 CD DVDs without using an adaptor It reads DVD ROMs at maximum 8 speed and CD ROMs at maximum 24 speed It writes CD R at up to 24 speed CD RW
65. SHIBA L10 Series Chapter 2 The Grand Tour This chapter identifies the various components of your computer Become familiar with each component before you operate the computer Front with the display closed The following figure shows the computer s front with its display panel in the closed position Speaker Display Latch Wireless Speaker Communication Switch Front of the computer with display closed Speakers The speakers emit sound generated by your software as well as audio alarms such as low battery condition generated by the system Display Latch This latch secures the LCD panel in its closed position Slide the latch to open the display e Wireless Press to activate or deactivate the Wireless LAN T Communication feature Not available on all models Switch N Set the switch to off in airplanes and hospitals Check the wireless activity indicator It will stop glowing when the wireless communication function is off User s Manual The Grand Tour Left side The following figure shows the computer s left side Cooling Vents Headphone Jack Ea Ga External Monitor Port USB Ports Microphone Jack PC Card Slot The left side of the computer C3 External Monitor This 15 pin port lets you connect an external Port video display Analog VGA port supports VESA DDC2B compatible functions Cooling Vents Cooling vents help prevent the CPU
66. TOSHIBA L10 Series User s Manual TOSHIBA L10 Series Copyright 2004 by TOSHIBA Corporation All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of TOSHIBA No patent liability is assumed with respect to the use of the information contained herein TOSHIBA L10 Series Portable Personal Computer User s Manual First edition December 2004 Ownership and copyright of music video computer programs databases etc are protected by the copyright laws These copyrighted materials may be copied for private use at home only If beyond the limitation above you copy including to transform data formats or modify these materials transfer them or distribute them via the Internet without approval of copyright owners you may be subject to claims for compensation for damage and or criminal penalties due to infringements of copyrights or personal rights Please remember to observe the copyright laws when you use this product to copy the copyrighted works or perform other actions Please note that you may infringe the owner s rights protected by the copyright laws if you use the screen mode switching functions e g Wide mode Wide Zoom mode etc of this product to display enlarged images video at coffee shops or hotels for the purposes of profits or providing these to the public gt This product incorporates copyright protection technology that is protected
67. W drive employs a laser system To ensure proper use of this product please read this instruction manual carefully and retain for future reference Should the unit ever require maintenance contact an authorized service location W Use of controls adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure Wi To prevent direct exposure to the laser beam do not try to open the enclosure Location of the required label SERIAL NO MANUFACTURED COMPLIES WITH FDARADIATION PERFORMANCE STANDARDS 21 CFR SUBCHAPTER J CLASS 1 LASER PRODUCT LASER KLASSE 1 Panasonic Communications Co Ltd 1 62 4 Chome Minoshima Hakata ku Fukuoka Japan User s Manual xv TOSHIBA L10 Series International precautions CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT TO EN 60825 1 AFA 1 V Sls CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TOEN60825 ADVERSEL USYNLIG LASERSTRALING VED ABNING NAR SIKKERHEDSAF BRYDER ER UDE AF FUNKTION UNDGA UDSAETTSLSE FOR STRALING CAUTION This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT To use this model properly read the instruction manual carefully and keep this manual for your future reference In case of any trouble with this model please contact your nearest AUTHORIZED service station To prevent direct exposure to the laser beam do not try to open the enclosure VORSICHT
68. a in the left side menu 3 Mark the Verify data written to the disc after burning check box in the Data Options 4 Click the OK button DLA for TOSHIBA Note the following limitations when you use DLA Wi This software supports only rewritable discs DVD RW DVD RW and CD RW It does not support DVD R DVD R and CD R discs that are not rewritable E DLA does not support formatting the DVD RAM disc and writing to it They are performed by DVD RAM Driver Software The proper software works according to the disc inserted in the drive E Do not use any discs that have been formatted with packet writing software other than DLA Similarly do not use any discs that have been formatted with DLA with any packet writing software other than DLA When using a disc you are not familiar with format it by selecting Full Format before using it W Do notuse the Cut amp Paste function for files and folders A file or folder that has been cut may be lost if writing fails due to an error on the disc User s Manual 4 16 Operating Basics InterVideo WinDVD Creator Platinum Please refer to the on line Help for additional InterVideo WinDVD Creator information When writing the Setup files for the program into a disc formatted by DLA and starting Setup from this disc an error may occur In this case plase copy them to your hard disk and then run Setup Note the following limitations when you write video DVD 1 Editing digital
69. amage your Wireless Products User s Manual xxi General Precautions Limitation of Liability For damage occurring due to an earthquake or thunder fire beyond our responsibility action by third party other accident intentional or accidental mistakes by a user misuse use under abnormal conditions we do not take any responsibility For incidental damage loss of business profit business interruption etc occurring due to use or disability of the product we do not take any responsibility For damage occurring due to non observance of the contents described in the instruction manual we do not take any responsibility For damage occurring due to erroneous operation or hang up caused by use in combination with products not related to our company we do not take any responsibility Usage Restrictions Do not use the Wireless Products for controlling the following equipment W Equipment directly linked with human life corresponding to the following W Medical equipment such as life support systems equipment used in operations etc W Exhaust systems for gases such as poisonous gas etc and exhaust systems for smoke W Equipment that must be set up in compliance with various laws such as the Fire Services Act the Construction Standard Act etc WB Equipment corresponding to that mentioned above B Equipment linked with human safety or having a serious influence on the safe maintenance of public function etc b
70. apter2 The Grand Tour Front with the display closed Lulssulslsss 2 1 Eent Siders sa PPM 2 2 Right side ture a a a ea ae ERES a 2 3 EI CIh tee C LEE 2 4 Underside neon ire iE Sere re 2 5 Front with the display open illslssleseseleen 2 6 System amp Keyboard indicators 22000 eee e eee 2 8 USB floppy disk drive optional sllsseeesss 2 9 User s Manual Table of Contents Chapter 3 Chapter 4 Fixed optical media drives 000 eee eee 2 10 Region codes for DVD drives and media 2 10 Writable discs ioi ue RE heey Rr Re Rede dd ues 2 10 o Mcr 2 10 DVDS s iiieenrodfees eceregeenepexeenrefnerbribe ized 2 11 goulticrer Pc REM 2 11 DVD ROM amp CD R RW drive 0 ee 2 11 DVD Super Multi drive liiis 2 12 DVD Super Multi drive Supporting Double Layer 2 12 AG adaptor oe bk a wc denen a areal de don cR ged 2 13 Getting Started Setting up your work Space 0 cee ee eee 3 2 General conditions 0 0 0 cece eee 3 2 Placement of the computer 0000 0c eee eeeee 3 3 Seating and posture 1 ee 3 3 LORIN sda mere eet ees ete er ee RR pee Boe eS 3 4 Work habits ike beibke dene be eb ae eee 3 4 Installing the battery pack 0 200 e eee eee eee 3 5 Connecting the AC adaptor 0002 eee eee eee 3 6 Opening the display 000 cece eee eee 3 7 Turning
71. ata bits making the sum of the bits even or odd Parity can be set to none odd or even password A unique string of characters used to identify a specific user The computer provides various levels of password protection such as user supervisor and eject pel The smallest area of the display that can be addressed by software Equal in size to a pixel or group of pixels See pixel peripheral component interconnect An industry standard 32 bit bus peripheral device An I O device that is external to the central processor and or main memory such as a printer or a mouse pixel A picture element The smallest dot that can be made on a display or printer Also called a pel plug and play A capability with Windows that enables the System to automatically recognize connections of external devices and make the necessary configurations in the computer port The electrical connection through which the computer sends and receives data to and from devices or other computers printed circuit board PCB A hardware component of a processor to which integrated circuits and other components are attached The board itself is typically flat and rectangular and constructed of fiberglass to form the attachment surface program A set of instructions a computer can execute that enables it to achieve a desired result See also application prompt A message the computer provides indicating it is ready for or requires information or an action from yo
72. ating system and other files If problems persist contact your dealer User s Manual 8 7 Troubleshooting DVD ROM amp CD R RW drive For more information refer to Chapter 4 Operating Basics Problem Procedure You cannot access a Make sure the drive s drawer is securely closed CD DVD in the drive Press gently until it clicks into place Open the drawer and make sure the CD DVD is properly seated It should lie flat with the label facing up A foreign object in the drawer could block laser light from reading the CD DVD Make sure there is no obstruction Remove any foreign object Check whether the CD DVD is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner Refer to the Media care section in Chapter 4 Operating Basics for details on cleaning Some CD DVDs run The software or hardware configuration may be correctly but others do causing a problem Make sure the hardware not configuration matches your software s needs Check the CD DVD s documentation Check the type of CD DVD you are using The drive supports DVD ROM DVD ROM DVD Video CD ROM CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA Recordable CD CD R CD RW Check the region code on the DVD It must match that on the DVD ROM and CD R RW drive Region codes are listed in the Fixed optical media drives section in Chapt
73. ay If you must spend long periods at the computer finding ways to break up the routine can reduce stress and improve your efficiency Sit in a relaxed posture Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain Vary your posture frequently Occasionally stand up and stretch or exercise briefly Exercise and stretch your wrists and hands a number of times during the day Frequently look away from the computer and focus your eyes on a distant object for several seconds for example 30 seconds every 15 minutes Take frequent short breaks instead of one or two long breaks for example two or three minutes every half hour Have your eyes examined regularly and visit a doctor promptly if you suspect you might be suffering from a repetitive strain injury A number of books are available on ergonomics and repetitive strain injury or repetitive stress syndrome For more information on these topics or for pointers on exercises for such stress points as hands and wrists please check with your library or book vendor Also refer to the computer s Safety Instruction Manual User s Manual 3 4 Getting Started Installing the battery pack To install a battery follow the steps below N W The battery pack is a lithium ion battery which can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local o
74. blem Some letter keys produce numbers Output to screen is garbled LCD panel Apparent LCD problems Problem No display Problems above remain unresolved or other problems occur Hard disk drive Problem Computer does not boot from hard disk drive Slow performance Procedure Check that the numeric keypad overlay is not selected Press Fn F11 and try typing again Make sure the software you are using is not remapping the keyboard Remapping involves reassigning the meaning of each key Refer to your software s documentation If you are still unable to use the keyboard consult your dealer may be related to the computer s setup Procedure Press hot keys Fn F5 to change the display priority to make sure it is not set for an external monitor Refer to your software s documentation to determine if the software is causing the difficulty Run the diagnostic test Contact your dealer if the problems continue Procedure Check if a floppy disk is in the floppy disk drive If a floppy disk is inserted remove it and reboot There may be a problem with your operating system files Refer to your operating system documentation Your files may be fragmented Run Disk Defragmenter to check the condition of your files and disk Refer to your operating system documentation or online help for information on running Disk Defragmenter As a last resort reformat the hard disk Then reload the oper
75. ce and the computer Refer to Chapter 6 Power and Power Up Modes for details The AC adaptor W Use only the AC adaptor that came with the computer or an equivalent optional adaptor Use of the wrong adaptor could damage your computer TOSHIBA assumes no liability for any damage in such case Wi Use only the AC Adaptor supplied with your computer or an equivalent adapter that is compatible Use of any incompatible adaptor or other types of AC Adaptors may have a different voltage which could cause damage to your computer computer failure and or possible data loss Toshiba assumes no liability for any damage computer failure and or data loss caused by use of an incompatible adaptor Use only the AC adaptor supplied as an accessory Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture User s Manual 2 13 TOSHIBA L10 Series Chapter 3 Getting Started This chapter provides basic information to get you started using your computer It covers the following topics pmi o i User s Manual Setting up your work space for your health and safety Be sure also to read the Safety Instruction Manual This guide which is included with the computer explains product liability Installing the battery pack Connecting the AC adaptor Opening the display Turning on the power Windows XP setup Turning off the power Restarting
76. cedure Reseat the PC Card to make sure it is firmly connected Make sure the connection between the external device and the card is firm Check the card s documentation If problems persist contact your dealer If you are using a USB mouse also refer to the USB section in this chapter and to your mouse documentation TouchPad Problem On screen pointer does not respond to Pad operation Double tapping does not work The mouse pointer moves too fast or too slow Procedure The system might be busy If the pointer is shaped as an hourglass wait for it to return to its normal shape and try again to move it Try changing the double click speed setting in the mouse control utility 1 Open the Control Panel select the Printers and Other Hardware icon and press Enter 2 Select the Mouse icon and press Enter 3 Click the Buttons tab 4 Setthe double click speed as instructed and click OK If problems persist contact your dealer Try changing the speed setting in the mouse control utility 1 Open the Control Panel select the Printers and Other Hardware icon and press Enter 2 Select the Mouse icon and press Enter 3 Click the Pointer Options tab 4 Setthe speed as instructed and click OK User s Manual 8 11 Troubleshooting Problem The response of the TouchPad is too sensitive USB mouse Problem On screen pointer does not respond to mouse operation Double clicking do
77. d should contact your skin immediately wash it under running water to prevent rash If it contacts your clothes promptly remove them to prevent the fluid from contacting your skin or eyes Immediately turn off the power disconnect the AC adaptor and remove the battery if any of the following events are observed in the battery pack offensive or unusual odor excessive heat discoloration or deformation Never use the computer again until it has been checked by a TOSHIBA service provider It might generate smoke or fire or the battery pack might rupture Make sure the battery is securely installed in the computer before attempting to charge the battery pack Improper installation could generate smoke or fire or cause the battery pack to rupture Keep the battery pack out of reach of infants and children It can cause injury Caution 1 Never continue to use a battery pack after its recharging capacity has become impaired or after the display of a warning message indicating that the battery pack s power is exhausted Continued use of an exhausted or impaired battery pack could cause the loss of data Never dispose of battery packs with normal trash Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage Cover the terminals with electrical tape to prevent short circuits which could cause the battery pack to ignite or rupture Use only battery packs recommended by TOSHIB
78. daptor connected Battery partially Operates Quick charge charged or no Quick Charge LED Battery orange charge LED Battery orange No battery Operates No charge installed No charge LED Battery off LED Battery off Universal Battery charge is Operates AC above low battery ED Battery off adaptor trigger point not ted Battery charge is Operates connecte below low battery LED Battery flashes orange trigger point Battery charge is Computer shuts down exhausted No Battery Cannot operates installed LED Battery off User s Manual Power and Power Up Modes i Check the Battery indicator to determine the status of the battery pack The following indicator lights indicate the battery status Flashing orange Orange Green No light The battery charge is low The AC adaptor must be connected to recharge the battery Indicates the AC adaptor is connected and charging the battery Indicates the AC adaptor is connected and the battery is fully charged Under any other conditions the indicator does not light If the battery becomes too hot while it is being charged the charge will stop and the battery indicator will go out When the battery s temperature falls to a normal range charge will resume This occurs whether the computer s power is on or off Power indicator Check the Power indicator to determine the power status Green Blinking orange No light Indicat
79. data transfer speeds 40 times faster than the USB 1 1 standard The ports also support USB 1 1 The PC Card slot accommodates a 5 mm Type II card User s Manual 1 6 Introduction Multimedia Sound System Video Out Jack S Video Audio Video Control Buttons Headphone Jack Microphone Jack Communications Modem A Windows Sound System compatible sound system provides speakers as well as jacks for an external microphone and headphones The video out jack lets you transfer video data to external devices Data output depends on the type of device connected to the S Video cable Not all models support this feature Audio Video control buttons let you use the computer s optical media drive You can also use the buttons to control the computer s CD audio or DVD video player and Windows Media player when the system is on This jack outputs analog audio signals A 3 5 mm mini microphone jack enables connection of a three conductor mini jack for monaural microphone input An internal modem provides capability for data and fax communication It supports V 90 V 92 The speed of data transfer and fax depends on analog telephone line conditions It has a modem jack for connecting to a telephone line Both of V 90 and V 92 are supported only in USA Canada Australia UK France and Germany Only V 90 is available in other regions User s Manual 1 7 Introduction LAN Wireless LAN
80. e battery continue to charge at least another 20 minutes before turning on the computer If the indicator still does not glow the battery may be at the end of its operating life Replace it If you do not think the battery is at the end of its operating life see your dealer Battery doesn t power If you frequently recharge a partially charged the computer as long as battery the battery might not charge to its full expected potential Fully discharge the battery then try to charge it again Check the power consumption settings in the Power Options Consider using a power saving feature Real Time Clock Problem Procedure The BIOS setting and Charge in the RTC battery is exhausted or system date time are getting low You will need to set the date and time lost in the BIOS setup screen using the following procedure 1 Press F2 key BIOS setup will boot up 2 Set the date in System Date 3 Set the time in System Time 4 Press F10 key Confirmation message will appear 5 Press Enter key BIOS setup will terminate and the computer will be rebooted al After configuring the time and date for the Real Time Clock battery we recommend that you turn the power status of your computer to ON so that the Real Time Clock battery is charged User s Manual 8 6 Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration For more information refer to Chapter 5 The Keyboard Pro
81. e connected to the external monitor port on the computer The computer supports several video modes Refer to Appendix B Display Controller and Modes To connect a monitor follow the steps below 1 Turn the computer off 2 Connect the monitor to the external monitor port 3 Turn the monitor s power on 4 Turn the computer on When you turn on the power the Windows Bootup screen Windows9 Logo appears on the display device However the Windows Desktop appears on a display device that you used last time to shut down your PC if the display device exists when you turn on the power To change the display settings press Fn F5 If you disconnect the monitor before you turn the computer off be sure to press Fn F5 to switch to the internal display Refer to Chapter 5 The Keyboard for details on using hot keys to change the display setting User s Manual 7 8 Optional Devices TV pmi o A TV output feature is provided with some models You can connect a television set to the Video out jack on the computer Follow the steps below If a television is connected to the computer set the TV type in Display Properties Follow the steps below W TV single 1 Click start and click Control Panel then Appearance and Themes 2 Double click the Display icon to open the Display Properties window 3 Click the Settings tab and click the Advanced button 4 Click Intel Extreme Graphics2 for Mobile click Graphics
82. e glass cleaner on the display Spray a small amount of cleaner on a soft clean cloth and wipe the screen gently with the cloth JN Never spray cleaner directly onto the computer or let liquid run into any part of it Never use harsh or caustic chemical products to clean the computer B Remove the dust from the cooling vents on the Left side of the computer regularly with a vacuum cleaner Refer to Chapter 2 The Grand Tour Left side User s Manual 4 25 Operating Basics Moving the computer The computer is designed for rugged durability However a few simple precautions taken when moving the computer will help ensure trouble free operation W Make sure all disk activity has ended before moving the computer Check the Disk indicator on the computer WB ifa CD DVD is in the drive remove it Also make sure the drawer is securely closed Wi Turn off the power to the computer W Disconnect the AC adaptor and all peripherals before moving the computer E Close the display Do not pick up the computer by its display panel W Use the carrying case when transporting the computer W When carrying your computer be sure to hold it securely so that it does not fall or hit anything Wi Do not carry your computer by holding protruded portions Protruded portion User s Manual 4 26 TOSHIBA L10 Series Chapter 5 The Keyboard The computer s keyboard layouts are compatible with a 101 102 key enhanced keyboa
83. ecause it is not designed or manufactured for this type of use Wi Traffic control equipment for air railroad road marine transport etc WB Equipment used in atomic power plants etc W Equipment corresponding to that mentioned above User s Manual xxii General Precautions pmi o WARNING Turn OFF the Wireless Communication switch of Wireless Products in a congested place such as a crowded commuter train Keep this product away from a cardiac pacemaker at least 22cm Radio waves can potentially affect cardiac pacemaker operation thereby causing respiratory troubles Turn OFF the Wireless Communication switch inside a medical facility or near medical electric equipment Do not bring medical electric equipment close to the product Radio waves can potentially affect medical electric equipment thereby causing an accident due to malfunction Turn OFF the Wireless Communication switch near an automatic door fire alarm or other automatic control equipment Radio waves can potentially affect automatic control equipment thereby causing an accident due to malfunction Do not turn ON the Wireless Communication switch in aircraft or in places that generate or can generate radio interference Radio waves can potentially affect them causing an accident due to malfunction Monitor possible radio interference or other troubles to other equipment while the product is used If any effect is caused turn OFF the Wireless C
84. ed as standard equipment there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line E Incase of a lightning storm unplug the modem cable from the telephone jack B Do not connect the modem to a digital telephone line A digital line will damage the modem s LAN Jack This jack lets you connect to a LAN The adaptor has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX Refer to Chapter 4 Operating Basics for details User s Manual 2 4 The Grand Tour Underside The following figure shows the underside of the computer Make sure the display is closed before turning over your computer Battery Pack Battery Release Latch 2 o o 0 S amp S Battery Release ap Cooling Lock 1 Vents Memory Module Cover Wireless LAN Cover The underside of the computer CI Battery Release Slide this lock to prepare the battery pack for rh fim Lock 1 removal Ch Battery Release Slide and hold this latch to release the battery Latch 2 pack for removal For detailed information on removing the battery packs refer to Chapter 6 Power and Power Up Modes Battery Pack The battery pack powers the computer when the AC adaptor is not connected For detailed information on the battery pack refer to Chapter 6 Power and Power Up Modes Memory Module This cover protects two memory module socke
85. efore going into Standby Hibernation Mode Writing is completed if you can open the DVD Super Multi drive tray Set the computer on a level surface and avoid places subject to vibration such as airplanes trains or cars Do not use an unstable surface such as a stand Keep mobile phones and other wireless communication devices away from the computer Always copy data from the hard disk drive to the CD R RW DVD R RW RAM or DVD R RW disc Do not use cut and paste The original data will be lost if there is a write error User s Manual 4 14 Operating Basics RecordNow Basic for TOSHIBA Note the following limitations when you use RecordNow DVD Video cannot be created using RecordNow DVD Audio cannot be created using RecordNow You cannot use RecordNow s Audio CD for Car or Home CD Player function to record music to the DVD R RW or DVD R RW disc Do not use the Exact Copy function of RecordNow to copy DVDVideo and DVD ROM with copyright protection DVD RAM disc cannot be backed up with the Exact Copy function of RecordNow You cannot back up a CD ROM or CD R RW to DVD R RW or DVD R RW using the Exact Copy function of RecordNow You cannot back up DVD ROM DVD Video or DVD R RW or DVD R RW to CD R RW using the Exact Copy function of RecordNow RecordNow cannot record in packet format You might not be able to use the Exact Copy function of RecordNow to back up a DVD R RW or DVD R RW
86. el utility W Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time The computer needs this time to check the battery s remaining capacity and to calculate the remaining operating time based on the current power consumption rate and remaining battery capacity The actual remaining operating time may differ slightly from the calculated time With repeated discharges and recharges the battery s capacity will gradually decrease Therefore an often used older battery will not operate for as long as a new battery even when both are fully charged In this case Windows Power Options will indicate a 100 charge for both the old and new battery but the displayed estimated time remaining will be shorter for the older battery Maximizing battery operating time A battery s usefulness depends on how long it can supply power on a single charge How long the charge lasts in a battery depends on How you configure the computer for example whether you enable battery power saving options The computer provides a battery save mode which can be set in the Windows Power Options to conserve battery power This mode has the following options E System Standby W System Hibernation B Monitor power off How often and how long you use the hard disk optical disc and the floppy disk drive How much charge the battery contained to begin with How you use optional devices such as a
87. els Where present it supports the B and G standard but it is compatible with other LAN systems based on Direct Sequence Spread Spectrum Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802 11 Wireless LAN standard B Automatic Transmit Rate Select mechanism in the transmit range of 54 48 36 24 18 12 9 and 6 Mbit s IEEE 802 119 B Automatic Transmit Rate Select mechanism in the transmit range of 11 5 5 2 and 1 Mbit s IEEE 802 11b B Roaming over multiple channels Card Power Management B Wired Equivalent Privacy WEP data encryption based on the 128 bit encryption algorithm W Advanced Encryption Standard AES data encryption based on 128 bit encryption algorithm Y Wake up on LAN does not function on a Wireless LAN Security Wi Be sure to enable the encryption function otherwise you may expose your computer to illegal access by an outsider across the Wireless LAN which may cause intrusion eavesdropping and the loss or destruction of stored data TOSHIBA strongly recommend the customer to enable the encryption function BW TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof Wireless communication switch You can enable or disable the Wireless LAN function with the on off switch No transmissions are sent or received when the switch is off Slide the switch to the right to turn it on and to the left to turn it off Set t
88. energy emitted by other wireless devices such as mobile phones Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations TOSHIBA believes Wireless LAN is safe for use by consumers These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature In some situations or environments the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organisation These situations may for example include W Using the Wireless LAN equipment on board of aeroplanes or Wi n any other environment where the risk of interference to other devices or services is perceived or identified as harmful If you are uncertain of the policy that applies on the use of wireless devices in a specific organisation or environment e g airports you are encouraged to ask for authorisation to use the Wireless LAN device prior to turning on the equipment Safety Instruction for Wireless Products If your computer has a wireless function all safety instructions must be read carefully and must be fully understood before you attempt to use it This manual contains the safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries or could d
89. ent Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate 2 The user manual of analog equipment must contain the equipment s Ringer Equivalence Number REN and an explanation notice similar to the following The Ringer Equivalence Number REN of the modem which can vary For the REN of your modem refer to your modems label 7 The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 3 The standard connecting arrangement telephone jack type for this equipment is jack type s USOC RJ11C The IC registration number of the modem is shown below Canada 3652B RD01D620 User s Manual viii TOSHIBA L10 Series Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a va
90. er 2 The Grand Tour User s Manual 8 8 Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing make sure you are observing the following precautions Wi Use only media recommended by TOSHIBA E Do not use the mouse or keyboard during writing W Use only the software supplied with the computer for recording E Do not run or start other software during writing E Do not jar the computer during writing E Do not connect disconnect external devices or install remove internal cards during writing If problems persist contact your dealer DVD Super Multi drive and DVD Super Multi drive Supporting Double Layer For more information refer to Chapter 4 Operating Basics Problem Procedure You cannot access a Make sure the drive s drawer is securely closed CD DVD in the drive Press gently until it clicks into place Open the drawer and make sure the CD DVD is properly seated It should lie flat with the label facing up A foreign object in the drawer could block laser light from reading the CD DVD Make sure there is no obstruction Remove any foreign object Check whether the CD DVD is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner Refer to the Media care section in Chapter 4 Operating Basics for details on cleaning User s Manual 8 9 Troubleshooting Problem Procedure Some CD DVDs run The software or hardware configuration may be
91. er is connected to an AC power source Data in memory will be lost E fyou carry the computer on board an aircraft or into a hospital be sure to shut down the computer in Hibernation Mode or in shutdown mode to avoid radio signal interference Benefits of Standby Mode The Standby Mode feature provides the following benefits E Restores the previous working environment more rapidly than does Hibernation Mode B Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature Wi You can use the panel power off feature User s Manual 3 11 Getting Started Entering Standby Mode You can enter Standby Mode in one of three ways 1 Click Start click Turn Off Computer and click Stand by 2 Close the display panel 3 Press the power button When you turn the power back on you can continue where you left when you shut down the computer M You can also enable Standby by pressing Fn F3 Refer to Chapter 5 The Keyboard for details F W When the computer is shut down in Standby Mode the power indicator I flashes orange E fyou are operating the computer on battery power you can lengthen the operating time by shutting down in Hibernation Mode as Standby Mode consumes more power Standby Mode limitations Standby Mode will not function under the following conditions B Power is turned back on immediately after shutting down
92. erver or any other network device W Writing with software other than RecordNow has not been confirmed Therefore operation with other software cannot be guaranteed When writing or rewriting Note the following when you write or rewrite a CD R or CD RW E Always copy data from the hard disk drive to the CD Do not use cut and paste The original data will be lost if there is a write error W Do not perform any of the following actions W Change users in the Windows XP operating system E Operate the computer for any other function including use of a mouse or TouchPad closing opening the LCD panel W Start a communication application such as a modem W Apply impact or vibration to the PC Wi Install remove or connect external devices including the following PC Card USB devices external display optical digital devices M Open the optical media drive E If the media is poor in quality dirty or damaged writing or rewriting errors may occur E Set the computer on a level surface and avoid places subject to vibration such as airplanes trains or cars Do not use an unstable surface such as a stand B Keep mobile phones and other wireless communication devices away from the computer User s Manual 4 10 Operating Basics Disclaimer DVD ROM and CD R RW drive TOSHIBA does not bear responsibility for the following B Damage to any CD R RW disc that may be caused by writing or rewriting with this product
93. es not work Procedure Adjust the touch sensitivity Open the Control Panel Click the Printers and Other Hardware icon Click the Mouse icon Click the Device Setting tab Click the Setting button The Properties for Synaptics Touchpad on PS 2 port screen appears Double click Sensitivity in the Select an item section on the left side of the screen 7 PalmCheck and Touch Sensitivity are displayed Click Touch Sensitivity 8 Move the slide bar for Touch Sensitivity to make an adjustment Click the OK button 9 Click the OK button on the Device Setting tab D Oe OON gt Procedure The system might be busy If the pointer is shaped as an hourglass wait for it to resume its normal shape and try again to move it Make sure the mouse is properly connected to the USB port Try changing the double click speed setting in the mouse control utility 1 Open the Control Panel select the Printers and Other Hardware icon and press Enter 2 Select the Mouse icon and press Enter 3 Click the Buttons tab 4 Set the double click speed as instructed and click OK User s Manual 8 12 Troubleshooting USB Problem Procedure The mouse pointer Try changing the speed setting in the mouse moves too fast or too Control utility slow 1 Open the Control Panel select the Printers and Other Hardware icon and press Enter 2 Select the Mouse icon and press Enter 3 Click the Pointer Options tab 4 S
94. es orange indicating that only a few minutes of battery power remain If you continue to use the computer while the Battery indicator flashes the computer enables Hibernation Mode so you don t lose data and automatically turns off a The computer enters Hibernate Mode only if Hibernation is enabled at the I Hibernate tab in Power Options You must recharge a battery pack when it becomes discharged Procedures To recharge a battery pack while it is installed in the computer connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet The Battery indicator glows orange when the battery is being charged JN Use only the computer connected to an AC power source to charge the battery pack Never attempt to charge the battery pack with any other charger User s Manual 6 7 Power and Power Up Modes ik i Time The following table shows the approximate time required to fully charge a discharged battery Charging time hours Battery type Power on Power off Battery pack 4300 mAh About 6 orlonger About 3 RTC battery About 24 Doesn t charge The charging time when the computer is on is affected by ambient temperature the temperature of the computer and how you use the computer If you make heavy use of external devices for example the battery might scarcely charge at all during operation Refer also to the section Maximizing battery operating time Battery charging notice The batter
95. es power is being supplied to the computer and the computer is turned on Indicates power is being supplied to the computer while the computer is in Standby Mode The indicator turns on for one second and off for two seconds Under any other conditions the indicator does not light User s Manual 6 2 Power and Power Up Modes Battery types A The computer has the following batteries E Battery pack 4300mAh B Real Time Clock RTC battery W The battery pack is a lithium ion battery which can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations Use only batteries recommended by TOSHIBA as replacements W Do notremove the battery pack while the computer is in Standby Mode Data is stored in RAM so if the computer loses power it will be lost When the computer is powered off in Standby Mode and the AC adaptor is not connected the main battery pack supplies power to maintain data and programs in memory If the battery pack is completely discharged Standby Mode does not function and the computer loses all data in memory Battery pack When the AC adaptor is not connected the computer s main power source is a removable lithium ion battery pack also referred to in this manual as the main battery You can purchase additional battery packs for extended use of the computer away from an AC power source Before you remove the battery pack
96. et the speed as instructed and click OK The mouse pointer The mouse might be dirty Refer to your mouse moves erratically documentations for instructions on cleaning If problems persist contact your dealer Refer also to your USB device s documentation Problem Procedure USB device does not Check for a firm cable connection between the work USB ports on the computer and the USB device Make sure the USB device drivers are properly installed Refer to your Windows XP documentation for information on checking the drivers If problems persist contact your dealer Memory expansion Refer also to Chapter 7 Optional Devices for information on installing memory modules Problem Procedure The computer hangs up Make sure the memory module installed in the and issues sounds A expansion slot is compatible with the computer long beep three short f an incompatible module has been installed beeps three short follow the steps below beeps and then a long 1T ff th beep Turn off the power 2 Disconnect the AC adaptor and all periph eral devices 3 Remove the battery pack Remove the memory module 5 Replace the battery pack and or connect the AC adaptor 6 Turn on the power If problems persist contact your dealer A User s Manual Troubleshooting Sound system Refer also to documentation for your audio devices Problem No sound is heard Monitor Refer also to Chapter 7 Optional
97. evice drivers that MS DOS loads when you turn the computer on dialog box A window that accepts user input to make system settings or record other information disk drive The device that randomly accesses information on a disk and copies it to the computer s memory It also writes data from memory to the disk To accomplish these tasks the unit physically rotates the disk at high speed past a read write head User s Manual Glossary 5 Glossary disk storage Storing data on magnetic disk Data is arranged on concentric tracks much like a phonograph record display A CRT LCD or other image producing device used to view computer output documentation The set of manuals and or other instructions written for the users of a computer system or application Computer system documentation typically includes procedural and tutorial information as well as system functions DOS Disk Operating System See operating system driver A software program generally part of the operating system that controls a specific piece of hardware frequently a peripheral device such as a printer or mouse DVD RAM A Digital Versatile Disc Random Access Memory is a highcapacity high performance disc that lets you store large volumes of data The DVD ROM drive uses a laser to read data from the disc DVD ROM A Digital Versatile Disc Read Only Memory is a high capacity high performance disc suitable for play back of video and other high density
98. evice or another computer hot key The computer s feature in which certain keys in combination with the extended function key Fn can be used to set system parameters such as speaker volume HW Setup A TOSHIBA utility that lets you set the parameters for various hardware components I icon A small graphic image displayed on the screen or in the indicator panel In Windows an icon represents an object that the user can manipulate i LINK IEEE1394 This port enables high speed data transfer directly from external devices such as digital video cameras input The data or instructions you provide to a computer communication device or other peripheral device from the keyboard or external or internal storage devices The data sent or output by the sending computer is input for the receiving computer User s Manual Glossary 7 Glossary instruction Statements or commands that specify how to perform a particular task interface 1 Hardware and or software components of a system used specifically to connect one system or device to another 2 To physically connect one system or device to another to exchange information 3 The point of contact between user the computer and the program for example the keyboard or a menu interrupt request A signal that gives a component access to the processor 1 0 Input output Refers to acceptance and transfer of data to and from a computer I O devices Equipment used to co
99. files The DVD ROM drive uses a laser to read data from the disc echo To send back a reflection of the transmitted data to the sending device You can display the information on the screen or output it to the printer or both When a computer receives back data it transmitted to a CRT or other peripheral device and then retransmits the data to printer the printer is said to echo the CRT erase See delete escape 1 A code ASCII code 27 signaling the computer that what follows are commands used with peripheral devices such as printers and modems 2 Ameans of aborting the task currently in progress escape guard time A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data and escapes that are intended as a command to the modem execute To interpret and execute an instruction Extended Capability Port An industry standard that provides a data buffer switchable forward and reverse data transmission and run length encoding RLE support E fast infrared An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps file A collection of related information a file can contain data programs or both firmware A set of instructions built into the hardware which controls and directs a microprocessor s activities User s Manual Glossary 6 Glossary floppy disk A removable disk that stores ma
100. floppy disk drive should be placed on a flat horizontal I surface when in use Do not set the drive on an incline greater than 20 while it is operating E Do not set anything on top of the floppy disk drive User s Manual 2 9 The Grand Tour Fixed optical media drives One of the following optical media drives is installed in the computer DVD ROM amp CD R RW or DVD Super Multi drives An ATAPI interface controller is used for CD DVD ROM operation When the computer is accessing a CD DVD an indicator on the drive glows Region codes for DVD drives and media DVD ROM amp CD R RW and the DVD Super Multi drives and their associated media are manufactured according to the specifications of six marketing regions When you purchase DVD Video make sure it matches your drive otherwise it will not play properly Code Region 1 Canada United States 2 Japan Europe South Africa Middle East 3 Southeast Asia East Asia 4 Australia New Zealand Pacific Islands Central America South America Caribbean 5 Russia Indian Subcontinent Africa North Korea Mongolia 6 China Writable discs CDs This section describes the types of writable CD DVD discs Check the specifications for your drive for the type of discs it can write Use RecordNow to write compact discs Refer to Chapter 4 Operating Basics mM CD R discs can be written only once The recorded data cannot be erased or changed B CD RW discs can be recorded m
101. function Computer s speaker Communication specifications Communication Data Full duplex System Fax Half duplex User s Manual A 2 Specifications Communication protocol Communication Speed Transmitting level Receiving level Input output impedance Error correcting Data compression Power supply Data ITU T Rec V 21 V 22 V 22bis V 32 Former CCITT V 32bis V 34 V 90 Bell 103 212A Fax ITU T Rec V 17 V 29 V 27ter V 21 ch2 Former CCITT Data transmission and reception 300 1200 2400 4800 7200 9600 12000 14400 16800 19200 21600 24000 26400 28800 31200 33600 bps Data reception only with V 90 28000 29333 30666 32000 33333 34666 36000 37333 38666 40000 4 1333 42666 44000 45333 46666 48000 49333 50666 52000 53333 54666 56000 bps Fax 2400 4800 7200 9600 12000 14400 bps 10 dBm 10 to 40 dBm 600 ohms 30 MNP class 4 and ITU T V 42 MNP class 5 and ITU T V 42bis 3 3V supplied by computer A 3 TOSHIBA L10 Series Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular picture elements pels on or off The controller is an advanced Video Graphics Array VGA that provides Extended Graphics Array XGA support for the internal LCD and external monitors The following is available W 15 0 XGA 1024 horizontal x 768 vertical pixels A high resolution external monitor
102. g features Do not write while virus check software is running Wait for it to finish and then disable virus detection programs including any software that checks files automatically in the background Do not use hard disk utilities including those intended to enhance HDD access speed They may cause unstable operation and data damage Write from the computer s hard disk drive to the CD DVD Do not try to write from shared devices such as a LAN server or any other network device Writing with software other than RecordNow is not recommended User s Manual 4 13 Operating Basics When writing or rewriting Please observe consider the following when you write or rewrite to a CD R RW DVD R RW RAM or DVD R RW disc Do not perform any of the following actions when writing or rewriting W Change users in the Windows XP operating system Wi Operate the computer for any other function including using a mouse or TouchPad or closing opening the LCD panel E Start a communication application such as a modem W Apply impact or vibration to the computer Wi Install remove or connect external devices including the following PC Card USB devices external display optical digital devices Wi Use the audio video control buttons to reproduce music or voice B Open the DVD Super Multi drive Do not use shut down log off and Standby Hibernation Mode while writing or rewriting Make sure writing or rewriting is completed b
103. gnetically encoded data floppy disk drive FDD An electromechanical device that reads and writes to floppy disks Fn esse A TOSHIBA utility that lets you assign functions to hot keys folder An icon in Windows used to store documents or other folders format The process of readying a blank disk for its first use Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk function keys The keys labeled F1 through F12 that tell the computer to perform certain functions gigabyte GB A unit of data storage equal to 1024 megabytes See also megabyte graphics Drawings pictures or other images such as charts or graphs to present information hard disk A non removable disk usually referred to as drive C The factory installs this disk and only a trained engineer can remove it for servicing Also called fixed disk hard disk drive HDD An electromechanical device that reads and writes a hard disk See also hard disk hardware The physical electronic and mechanical components of a computer system typically the computer itself external disk drives etc See also software and firmware hertz A unit of wave frequency that equals one cycle per second hexadecimal The base 16 numbering system composed of the digits 0 through 9 and the letters A B C D E and F host computer The computer that controls regulates and transmits information to a d
104. h the modem at the other end of the call and b the application using the modem is compatible with the application at the other end of the call e g accessing the Internet requires suitable software in addition to a modem W This equipment shall not be used in any manner which could constitute a nuisance to other Telecom customers W Some parameters required for compliance with Telecom s PTC Specifications are dependent on the equipment PC associated with this modem The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications a There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation and b The equipment shall go on hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next c Automatic calls to different numbers shall be not less than 5 seconds apart User s Manual TOSHIBA L10 Series Immediately disconnect this equipment should it become physically damaged and arrange for its disposal or repair The correct settings for use with this modem in New Zealand are as follows ATBO CCITT operation AT amp G2 1800 Hz guard tone AT amp P1 Decadic dialing make break ratio 3390 6796 ATSO 0 not auto answer ATS10 less than 150 loss of carrier to hangup delay factory default of 15 recommended ATS11 90 DTMF dialing on off durati
105. harged for each variation when submitted at the same time as the original An invoice for NZ1237 50 will be sent under separate cover Optical disc drive safety instructions i Be sure to check the international precautions at the end of this section User s Manual xi TOSHIBA L10 Series Panasonic DVD Super Multi UJ 830B W The DVD Super Multi drive employs a laser system To ensure proper use of this product please read this instruction manual carefully and retain for future reference Should the unit ever require maintenance contact an authorized service location E Use of controls adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure Wi 7o prevent direct exposure to the laser beam do not try to open the enclosure Location of the required label SERIAL NO MANUFACTURED COMPLIES WITH FDARADIATION PERFORMANCE STANDARDS 21 CFR SUBCHAPTER J CLASS 1 LASER PRODUCT LASER KLASSE 1 Panasonic Communications Co Ltd 1 62 4 Chome Minoshima Hakata ku Fukuoka Japan User s Manual xii TOSHIBA L10 Series Panasonic DVD Super Multi UJ 840B W The DVD Super Multi drive employs a laser system To ensure proper use of this product please read this instruction manual carefully and retain for future reference Should the unit ever require maintenance contact an authorized service location Use of controls adjustments or the
106. harging and flashing orange indicates a low battery charge Refer to Chapter 6 Power and Power Up Modes Shows you Wireless LAN activity and whether the Wireless LAN feature is engaged or not Not available on all models The Built in HDD ODD indicator glows green when the computer accesses the hard disk drive or and optical disk drive This indicator glows green when the alphabet keys are locked in uppercase You can use the keypad overlay gray labeled keys for numeric input when the Numeric mode indicator lights green Refer to the Keypad overlay section in Chapter 5 The Keyboard User s Manual 2 8 The Grand Tour USB floppy disk drive optional An optional 3 72 floppy disk drive accommodates 1 44 megabyte or 720 kilobyte floppy disks It connects to the USB port Disk In Use Floppy Eject Indicator Disk Slot Button USB floppy disk drive Disk In Use Indicator This indicator lights when the floppy disk is being accessed Floppy Disk Slot Insert a floppy disk in this slot Eject Button When a floppy disk is fully seated in the drive the eject button pops out To remove a floppy disk push in the eject button and the floppy disk pops out partially for removal JN Check the Disk In Use indicator when you use the floppy disk drive Do not press the eject button or turn off the computer while the light is glowing Doing so could destroy data and damage the floppy disk or the drive 3 E The external
107. he overlay 1 Hold Fn and press any other key All keys will operate as if the overlay were off 2 Type upper case characters by holding Fn Shift and pressing a character key 3 Release Fn to continue using the overlay Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation But you can generate these characters using their ASCII codes With the overlay on 1 Hold down Alt 2 Using the overlay keys type the ASCII code 3 Release Alt and the ASCII character appears on the display screen With the overlay off 1 Hold down Alt Fn 2 Using the overlay keys type the ASCII code 3 Release Alt Fn and the ASCII character appears on the display screen User s Manual 5 7 TOSHIBA L10 Series Chapter 6 Power and Power Up Modes The computer s power resources include the AC adaptor and internal batteries This chapter gives details on making the most effective use of these resources including charging and changing batteries tips for saving battery power and power up modes Power conditions The computer s operating capability and battery charge status are affected by the power conditions whether an AC adaptor is connected whether a battery is installed and what the charge level is for the battery Table Power conditions Power on Power off no operation Universal Battery fully Operates LED Battery green AC charged LED Battery green a
108. he screen and the system does not function normally Wi The screen displays an error message Turn off the computer and check all cable connections If the test fails again contact your dealer Power When the computer is not plugged into an AC outlet the battery pack is the primary power source However your computer has a number of other power resources including an intelligent power supply and a Real Time Clock battery These resources are interrelated and any one could affect apparent power problems This section provides checklists for AC power and the battery If you cannot resolve a problem after following them the cause could lie with another power resource In such a case contact your dealer Overheating power down If the computer s internal temperature becomes too high the computer will automatically enter Hibernation Mode or Standby Mode and shut down If the computer has reached room temperature and still does not start or if it starts but shuts down quickly contact your dealer User s Manual 8 4 Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected check the Battery Indicator indicator Refer to Chapter 6 Power and Power Up Modes for more information Problem Procedure AC adaptor doesn t Check the connections Make sure the cord is power the computer firmly connected to the computer and a power outlet Check the condition of the cord and terminals
109. he switch to off in airplanes and hospitals Check the indicator It will stop glowing when the wireless communication function is off User s Manual 4 23 Operating Basics Wireless communication indicator LAN The wireless communication indicator indicates the status of the wireless communication functions Indicator status Indication Indicator off Wireless communication switch is set to off Automatic power down because of overheating Power malfunction Wireless communication switch is on Wireless Indicator glows LAN is turned on by an application If you used the Task Bar to disable Wireless LAN you will need to restart the computer to re enable it Alternatively you can also follow this procedure 1 In the Control Panel click Performance and Maintenance then System 2 Select the Hardware tab 3 Click the Device Manager The Device Manager window opens Click Network Adapters 4 Select your preferred Network Adapter then click the Enable button in the task bar The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX This section describes how to connect disconnect to a LAN LAN cable types The computer must be configured properly before connecting to a LAN Logging onto a LAN using the computer s default settings could cause a malfunction in LAN operation Check with your LAN administrator regarding
110. hes to the outside to release the module A spring will force one end of the module up User s Manual 7 6 Optional Devices 5 Grasp the module by the sides and pull it out WN E f you use the computer for a long time the memory modules will become hot In this case let the memory modules cool to room temperature before you replace them Or you will get burnt if you touch any of them Wi Do not touch the connectors on the memory module or on the computer Debris on the connectors may cause memory access problems Latches Removing the memory module 6 Seatthe cover and secure it with a screw and replace the battery pack Additional battery pack You can increase the portability of the computer with additional battery packs If you re away from an AC power source and your battery runs low you can replace it with a freshly charged battery Refer to Chapter 6 Power and Power Up Modes Additional AC adaptor If you frequently transport the computer between different sites such as your home and office purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load User s Manual 7 7 Optional Devices USB floppy disk drive The 3 72 external floppy disk drive module can be connected to the USB port For details on connecting the 3 2 external floppy disk drive module refer to Chapter 4 Operating Basics External monitor An external analog monitor can b
111. id crystal display User s Manual Glossary 1 Glossary LED light emitting diode LSI large scale integration MS DOS Microsoft Disk Operating System OCR optical character recognition reader PCB printed circuit board PCI peripheral component interconnect RAM random access memory RGB red green and blue ROM read only memory RTC real time clock SCSI small computer system interface S O serial input output SXGA super extended graphics array plus TFT thin film transistor UART universal asynchronous receiver transmitter USB Universal Serial Bus UXGA ultra extended graphics array VESA Video Electronic Standards Association VGA video graphics array VRT voltage reduction technology XGA extended graphics array A adaptor A device that provides an interface between two dissimilar electronic devices For example the AC adaptor modifies the power from a wall outlet for use by the computer This term also refers to the add in circuit cards that control external devices such as video monitors and magnetic tape devices allocate To assign a space or function for a specific task alphanumeric Keyboard characters including letters numbers and other symbols such as punctuation marks or mathematical symbols alternating current AC Electric current that reverses its direction of flow at regular intervals analog signal A signal whose characteristics such as amplitude and frequency vary in prop
112. ignal is related to the transmit rate of the wireless communication Communications at lower transmit range may travel larger distances E The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high density materials E Range is also impacted due to obstacles in the signal path of the radio that may either absorb or reflect the radio signal User s Manual C 2 Wireless LAN Supported Frequency Sub bands Subject to the radio regulations that apply in the countries regions your Wireless LAN card may support a different set of 2 4 GHz channels Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries regions Wireless IEEE 802 11 Channels Sets Revision B and G Frequency Range Channel ID 1 Qo 0 020 N j o0 12 13 2400 2483 5 MHz 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 1 2462 2467 2 2472 2 1 Factory set default channels 2 Refer to the sheet Approved Countries Regions for use for the countries regions that in which these channels can be used User s Manual C 3 Wireless LAN When installing Wireless LAN cards the channel configuration is managed as follows For wireless clients that operate in a Wireless LAN Infrastructure the Wireless LAN card will automatically start operation at the channel identified by the Wireles
113. igure Below eye level a 90 angles le ee J uu Jddddd l Posture and positioning of the computer Place your chair so that the keyboard is at or slightly below the level of your elbow You should be able to type comfortably with your shoulders relaxed Your knees should be slightly higher than your hips If necessary use a foot rest to raise the level of your knees to ease pressure on the back of your thighs Adjust the back of your chair so it supports the lower curve of your spine Sit straight so that your knees hips and elbows form approximately 90 degree angles when you work Do not slump forward or lean back too far User s Manual 3 3 Getting Started Lighting Proper lighting can improve legibility of the display and reduce eyestrain Position the computer so that sunlight or bright indoor lighting does not reflect off the screen Use tinted Windows shades or other screen to eliminate sun glare Avoid placing the computer in front of bright light that could shine directly in your eyes If possible use soft indirect lighting in your computer work area Use a lamp to illuminate your documents or desk but be sure to position the lamp so that it does not reflect off the display or shine in your eyes Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities If possible schedule a variety of tasks into your workd
114. ilure to follow instructions may cause data loss or damage your equipment F Please read A note is a hint or advice that helps you make best use of your equipment Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions User s Manual xxxii TOSHIBA L10 Series Chapter 1 Introduction This chapter provides an equipment checklist and it identifies the computer s features options and accessories JN Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA Equipment checklist Carefully unpack your computer Save the box and packing materials for future use Hardware Check to make sure you have all the following items B TOSHIBA L10 Series Portable Personal Computer Wi Universal AC adaptor and power cord B Modular cable for modem optional part dependant on model purchased It is necessary to install the battery to use this computer Refer to Installing the battery pack section in Chapter 3 Getting Started i User s Manual Introduction Software Windows XP Home Edition or Professional The following software is preinstalled Microsoft Windows XP Home Edition or Professional B Modem driver Display driver for Windows TOSHIBA Utilities Wireless LAN driver Can be used only with Wireless LAN models Sound driver fo
115. ion battery which can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations Use only batteries recommended by TOSHIBA as replacements Wi Do not touch the latch while holding the computer Or you may get injured by the dropped battery by unintentional release of the latch Turn the computer s power off Disconnect all cables connected to the computer Insert the battery pack Ensure the battery release lock 1 is moved into its locked position fon S Battery pack Battery Release Lock 1 MINIL c VIII Securing the battery pack User s Manual 6 12 Power and Power Up Modes Power up modes The computer has the following power up modes B Boot Mode Computer shuts down without saving data Always save your work before you turn the computer off in boot mode B Hibernation Mode Data in memory is saved to the hard disk W Standby Mode Data is maintained in the computer s main memory 3 Refer also to the sections Turning on the power and Turning off the power I in Chapter 3 Getting Started Windows utilities You can specify the setting in the Windows Power Options Hot keys You can use hot keys Fn F3 to enter Standby Mode and Fn F4 to enter Hibernation Mode Refer to Chapter 5 The Keyboard for details Panel power off on You can set up your computer so that power turns off automatically when
116. ity enables the system to recognize the connection and make the necessary configurations automatically User s Manual 1 8 Introduction Special features i The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use Please note that the descriptions for starting some special features are based on setting the Control Panel to Category View On Classic view the description is different Hot Keys Keypad Overlay Power On Password Instant Security Display Automatic Power Off HDD Automatic Power Off Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program A ten key pad is integrated into the keyboard Refer to the Keypad overlay section in Chapter 5 The Keyboard for instructions on using the keypad overlay Two levels of password security supervisor and user are available to prevent unauthorized access to your computer To register a supervisor password double click the TOSHIBA Console on your desktop select the Security tab and start the Supervisor password utility To set a user password click start Control Panel Printers and Other Hardware TOSHIBA HWSetup At Password tab you can register a user password The hot key function Fn F1 blanks the screen and disables the computer providing data security This feature automaticall
117. l in EG 201 121 Germany ATAAB ANO005 ANO006 AN007 AN009 ANO010 and DE03 04 05 08 09 12 14 17 Greece ATAAB ANO05 ANO006 and GRO1 02 03 04 Portugal ATAAB ANO001 005 006 007 011 and P03 04 08 10 Spain ATAAB ANO005 007 012 and ESO1 Switzerland ATAAB ANO002 All other countries ATAAB ANO003 004 regions Specific switch settings or software setup are required for each network please refer to the relevant sections of the user guide for more details The hookflash timed break register recall function is subject to separate national type approvals It has not been tested for conformity to national type regulations and no guarantee of successful operation of that specific function on specific national networks can be given User s Manual TOSHIBA L10 Series Japan regulations Region selection If you are using the computer in Japan technical regulations described in the Telecommunications Business Law require that you select the Japan region mode It is illegal to use the modem in Japan with any other selection Redial Up to two redial attempts can be made If more than two redial attempts are made the modem will return DELAYED If you are experiencing problems with the DELAYED code set the interval between redials at one minute or longer Japan s Telecommunications Business Law permits up to two redials on analogue telephones but the redials must be made within a total of three minutes The internal modem is
118. lable on all models User s Manual 8 15 Troubleshooting Printer Problem Procedure Printer does not turn on Check that the printer is connected to an electric outlet Make sure the outlet is supplying power by plugging in an appliance Computer printer do not Make sure the printer is turned on and is online communicate ready to use Inspect the cable connecting the printer to the computer for damage Make sure it is securely connected Make sure your software is configured to recognize the printer Check your printer and software documentation Printer error Check your printer documentation If problems persist contact your dealer TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer you may need to contact TOSHIBA for additional technical assistance Before you call Some problems you experience may be related to software or the operating system it is important to investigate other sources of assistance first Before contacting TOSHIBA try the following B Review troubleshooting sections in the documentation for software and peripheral devices Wi ifa problem occurs when you are running software applications consult the software documentation for troubleshooting suggestions Call the software company s technical support for assistance W Consult the dealer you purchased your computer and or software from They are your best source
119. lid Austel permit This modem has been designed to specifically configure to ensure compliance with Austel standards when the country region selection is set to Australia The use of other country region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non compliant manner To verify that the country region is correctly set enter the command ATI which displays the currently active setting To set the country region permanently to Australia enter the following command sequence AT GCI 09 Failure to set the modem to the Australia country region setting as shown above will result in the modem being operated in a non compliant manner Consequently there would be no permit in force for this equipment and the Telecoms Act 1991 prescribes a penalty of 12 000 for the connection of non permitted equipment Notes for use of this device in New Zealand Wi The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers Failure to operate should not be reported as a fault to Telecom Wi In addition to satisfactory line conditions a modem can only work properly if a itis compatible wit
120. me with additional software installed this software can not be recovered from the Product Recovery disk Re install these applications e g Works Suite DVD Player Games etc separately from other media User s Manual 3 13 TOSHIBA L10 Series Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad the optional USB floppy disk drive optical media drives audio video controls sound system modem the wireless LAN and LAN It also provides tips on caring for your computer and on heat dispersal Using the TouchPad To use the TouchPad simply touch and move your finger tip across it in the direction you want the on screen pointer to go TouchPad Z TouchPad control buttons TouchPad and TouchPad control buttons Two buttons below the keyboard are used like the buttons on a mouse pointer Press the left button to select a menu item or to manipulate text or graphics designated by the pointer Press the right button to display a menu or other function depending on the software you are using Do not press on the TouchPad too hard or press a sharp object such as a ball point pen against the TouchPad The TouchPad could be damaged User s Manual Operating Basics For some functions you can tap the TouchPad instead of pressing a control button 1 Click Tap the TouchPad once Double click Tap the TouchPad twice Drag and drop 1 Hold down the
121. mmunicate with the computer and transfer data to and from it IrDA 1 1 An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps jumper A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit K Taken from the Greek word kilo meaning 1000 often used as equivalent to 1024 or 2 raised to the 10th power See also byte and kilobyte KB See kilobyte keyboard An input device containing switches that are activated by manually pressing marked keys Each keystroke activates a switch that transmits a specific code to the computer For each key the transmitted code is in turn representative of the ASCII character marked on the key kilobyte KB A unit of data storage equal to 1024 bytes See also byte and megabyte level 2 cache See cache Light Emitting Diode LED A semiconductor device that emits light when a current is applied Liquid Crystal Display LCD Liquid crystal sealed between two sheets of glass coated with transparent conducting material The viewing side coating is etched into character forming segments with leads that extend to the edge of the glass Applying a voltage between the glass sheets alters the brightness of the liquid crystal LSI Large Scale Integration 1 A technology that allows the inclusion of up to 100 000 simple logic gates on a single chip 2 An integrated circuit that uses la
122. mplemented those options cables have to provide assurance that the system PC plus options cables still fulfils the required standards To avoid general EMC problems the following guidance should be noted W Only CE marked options should be connected implemented W Only best shielded cables should be connected Working environment J This product was designed to fulfill the EMC Electromagnetic Compatibility requirements to be observed for so called Residential commercial and light industry environments TOSHIBA do not approve the use of this product in working environments other than the above mentioned Residential commercial and light industry environments For example the following environments are not approved W Industrial Environments environments with a mains voltage gt 230V W Medical Environments W Automotive Environments E Aircraft Environments If this product is supplied with a network port please refer to the paragraph Network connection Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA The consequences of the use of this product in non approved working environments may be Wi Interference with other devices or machines in the near surrounding area Malfunction of or data loss from this product caused by disturbances generated by other devices or machines in the near surrounding area Therefore TOSH
123. n are the 12 keys at the top of your keyboard These keys function differently from other keys ald dhl lr Ke ET C F1 through F12 are called function keys because they execute programmed functions when pressed Used in combination with the Fn key keys marked with icons execute specific functions on the computer Refer to the section Soft keys Fn key combinations in this chapter The function executed by individual keys depends on the software you are using Soft keys Fn key combinations i The Fn function is used in combination with other keys to form soft keys Soft keys are key combinations that enable disable or configure specific features Some software may disable or interfere with soft key operations Soft key settings are not restored by the Standby Mode feature Emulating keys on enhanced keyboard E GEES TETTE eee ETT TT TCT TACT T ss es ce A 101 key enhanced keyboard layout The keyboard is designed to provide all the features of the 101 key enhanced keyboard shown in figure above The 101 102 key enhanced keyboard has a numeric keypad and scroll lock key It also has additional Enter and Ctrl keys to the right of the main keyboard Since the keyboard is smaller and has fewer keys some of the enhanced keyboard functions must be sim
124. nd two conductor For the United States and Canada plug configuration must be a 2 15P 250 V or 1 15P 125 V as designated in the U S National Electrical code handbook and the Canadian Electrical Code Part II The following illustrations show the plug shapes for the U S A and Canada the United Kingdom Australia and Europe USA and Canada UL approved CSA approved Australia AS approved United Kingdom BS approved Europe Approved by the appropriate agency User s Manual D 2 TOSHIBA L10 Series Glossary The terms in this glossary cover topics related to this manual Alternate naming is included for reference Abbreviations AC alternating current AGP accelerated graphics port ANSI American National Standards Institute APM advanced power manager ASCII American Standard Code for Information Interchange BIOS basic input output system CD ROM Compact Disc Read Only Memory CD RW Compact Disc Read Write CMOS complementary metal oxide semiconductor CPU central processing unit CRT cathode ray tube DC direct current DDC display data channel DMA direct memory access DOS disk operating system DVD digital versatile disc ECP extended capabilities port FDD floppy disk drive FIR fast infrared HDD hard disk drive IDE integrated drive electronics NO input output IrDA Infrared Data Association IRQ interrupt request KB kilobyte LCD liqu
125. ne Road Weybridge Surrey KT15 2UL The Rest of Europe TOSHIBA Europe I E GmbH Gesch ftsbereich Deutschland sterreich Hammfelddamm 8 D 41460 Neuss Germany 8 17 TOSHIBA L10 Series Appendix A Specifications This appendix summarizes the computer s technical specifications Physical Dimensions Weight typical 2 72 kilograms configured with 15 XGA 512MB x 1 RAM 40GB HDD Super Multi drive modem LAN 100M Bit 8cell battery Weight will vary with other configurations Above weights are measured at a specific criteria They are not guaranteed as the maximum weight of the actual product Size 332 w x 270 d x 28 5 36 6 h millimeters not including parts that extend beyond the main body User s Manual Specifications Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5 C 41 F to 35 C 95 F 20 to 80 Non operating 20 C 4 F to 65 C 10 to 90 149 F Thermal Gradient 20 C per hour maximum Wet bulb 26 C maximum temperature Conditions Altitude from sea level Operating 60 to 3 000 meters Non operating 60 to 10 000 meters maximum Power Requirements AC adaptor 100 240 volts AC 50 or 60 hertz cycles per second Computer 19 VDC 3 42 ampers Built in Modem Network control unit NCU Type of NCU AA Type of line Telephone line analog only Type of dialing Pulse Tone Control command AT commands EIA 578 commands Monitor
126. ner other than that described in the User s manual Never connect the battery pack to a plug socket or to an automobile s cigarette lighter socket It may rupture or ignite 6 Use only the battery pack supplied with the computer or other device or a battery pack approved by the computer or device s manufacturer Battery packs have different voltages and terminal polarities Use of an improper battery could cause smoke fire or rupture of the battery pack 7 Never subject a battery pack to heat such as storage near a heat Source Exposure to heat can cause the battery pack to ignite explode or leak caustic liquid and cause death or serious injury It could also fail or malfunction causing data loss User s Manual 6 5 Power and Power Up Modes 8 Never expose the battery pack to abnormal shock vibration or pressure The battery pack s internal protective device will fail causing it to overheat explode ignite or leak caustic liquids possibly resulting in death or serious injury Never let a battery pack become wet A wet battery pack will overheat ignite or rupture possibly resulting in death or serious injury Warning 1 Never allow caustic electrolyte fluid leaked from a battery pack to contact your eyes skin or clothing If caustic electrolyte fluid should contact your eyes immediately wash your eyes with large amounts of running water and seek medical attention to help prevent eye damage If electrolyte flui
127. ng magnetic fields e g stereo speakers B Some components in the computer including data storage media can be damaged by magnets Do not place the computer near magnetic objects or bring magnetic objects close to the computer Be careful of objects such as stereo speakers that produce strong magnetic fields during operation Also be careful with metal objects such as bracelets which can be inadvertently magnetized W Do not operate the computer in close proximity to a mobile phone B Leave ample ventilation room for the fan Do not block the vents User s Manual 3 2 Getting Started Placement of the computer Position the computer and peripheral devices to provide comfort and safety Set the computer on a flat surface at a comfortable height and distance The display should be no higher than eye level to avoid eyestrain Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices Allow adequate space behind the computer to let you freely adjust the display The display should be angled to reduce glare and maximize visibility If you use a paper holder set it at about the same height and distance as the computer Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain Refer to the following tips and to the following f
128. nnections use of complex modeling software such as high end computer aided design applications use of the computer in areas with low air pressure high altitude gt 1 000 meters or gt 3 280 feet above sea level E use of the computer at temperatures outside the range of 5 C to 35 C 41 F to 95 F or gt 25 C 77 F at high altitude all temperature references are approximate CPU Performance may also vary from specifications due to design configuration Under some conditions your computer product may automatically shutdown This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions To avoid risk of lost data always make back up copies of data by periodically storing it on an external storage medium For optimum performance use your computer product only under recommended conditions Read additional restrictions under Environmental Requirements in appendix A Specifications Contact TOSHIBA Technical Service and Support for more information User s Manual xix General Precautions CE compliance This product and the original options are designed to observe the related EMC Electromagnetic Compatibility and safety standards However TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented In this case the persons who have connected i
129. nt voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture JN Wi Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible Use of any incompatible adaptor could damage your computer TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor W When you connect the AC adaptor to the computer always follow the steps in the exact order as described in the User s Manual Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical change and cause an electrical shock or minor bodily injury when touched As a general safety precaution avoid touching any metal parts 1 Connect the power cord to the AC adaptor Connecting the power cord to the AC adaptor User s Manual 3 6 Getting Started 2 Connect the AC adaptor s DC output plug to the DC IN 19V jack on the back of the computer Connecting the adaptor to the computer 3 Plug the power cord into a live wall outlet Opening the display The display panel can be rotated in a wide range of angles for optimal viewing 1 Slide the display latch on the front of the computer to the right 2 Lift the panel up and adjust it to the best viewing angle for you Use reasonable care when opening and closing the display panel Opening it vigorously or slamming it shut
130. o the drawer might not open fully when you press the eject button Closing the disc drawer User s Manual 4 6 Operating Basics Removing discs To remove the disc follow the steps below and refer to the figure Do not press the eject button while the computer is accessing the disc drive Wait for the optical media drive indicator to go out before you open the drawer Also if the disc is spinning when you open the drawer wait for itto stop before you remove it 1 To pop the drawer partially open press the eject button Gently pull the drawer out until it is fully opened W When the drawer pops open slightly wait a moment to make sure the disc has stopped spinning before pulling the drawer fully open Wi Turn off the power before you use the eject hole If the disc is spinning when you open the drawer the disc could fly off the spindle and cause injury 2 The disc extends slightly over the sides of the drawer so you can hold it Hold the disc gently and lift it out Removing a CD DVD 3 Push the center of the drawer to close it Press gently until it locks into place User s Manual 4 7 Operating Basics Audio Video controls This section describes how to use the audio video control buttons Next and Previous buttons Press on the button to select the desired function Next Press the 1 button to advance to the next track chapter or data Previous Press the i button to advance to
131. o key activates the start menu and the other the application key has the same function as the secondary mouse button Am ae This key activates the Windows start menu E This key has the same function as the secondary mouse button Keypad overlay Your computer s keyboard does not have an independent numeric keypad but its numeric keypad overlay functions like one The keys in the center of the keyboard with gray letters make up the numeric keypad overlay The overlay provides the same functions as the numeric keypad on the 101 102 key enhanced keyboard described previously Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control Numeric mode To turn on the Numeric mode press Fn F11 The Numeric mode indicator lights Now try numeric data entry using the keys in the following figure Press Fn F11 again to turn off the overlay za aAa OP sm 7 8 8 LJ 3 i il aiid The numeric keypad overlay User s Manual 5 6 The Keyboard Temporarily using normal keyboard overlay on While using the overlay you can temporarily access the normal keyboard without turning off t
132. o make changes in their equipment operations or procedures If these changes might affect your service or the operation of your equipment the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service If problems arise If any of your telephone equipment is not operating properly you should immediately remove it from your telephone line as it may cause harm to the telephone network If the telephone company notes a problem they may temporarily discontinue service When practical they will notify you in advance of this disconnection If advance notice is not feasible you will be notified as soon as possible When you are notified you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC In the event repairs are ever needed on your modem they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation Disconnection If you should ever decide to permanently disconnect your modem from its present line please call the telephone company and let them know of this change Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the
133. oard port and microphone jack Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment User s Manual TOSHIBA L10 Series FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Contact Address TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 949 583 3000 BSMI Notice Taiwan Only SERA UR eee E AEPTIU T AR moi RAASHERRAE BE SHH R C EU Declaration of Conformity TOSHIBA declares that the product TOSHIBA L10 series conforms to the following Standards Supplementary The product complies with the requirements of Information the Low Voltage Directive 73 23 EEC the EMC Directive 89 336 EEC and or the R amp TTE Directive 1999 05 EEC This product is carrying the CE Mark in accordance with the related European Directives Responsible for CE Marking is TOSHIBA Europe Hammfelddamm 8 41460 Neuss Germany VCCI Class B Information eld PRUBSESERESAEMAMBS VCCI ORS EoD SRORMEREE CS TOREA RERRCHATSCe HRM ULCUzA2 TOREDIG TETLEY a YRRIR T RASNE SERBS FROTCEMHBVET WRAT o TE LUBY RUALTRS US U
134. oftware problem check your hardware First run through the items in the preliminary checklist above If you still cannot correct the problem try to identify the source The next section provides checklists for individual components and peripherals Hardware and system checklist This section discusses problems caused by your computer s hardware or attached peripherals Basic problems may occur in the following areas System start up Self test Power Keyboard LCD panel Hard disk drive DVD ROM and CD R RW drive DVD Super Multi drive Floppy disk drive optional PC Card System start up When the computer does not start properly check the following items E Power on Password Self Test Power Sources E Pointing device USB Memory expansion Sound system Monitor Modem LAN Wireless LAN Printer User s Manual 8 3 Troubleshooting Self test When the computer starts up the self test will be run automatically and the following will be displayed In Touch with Tomorrow B TOSHIBA This message remains on the screen for a few seconds If the self test is successful the computer tries to load the operating system depending on how the Boot Priority is set in the TOSHIBA HW Setup program If any of the following conditions are present the self test failed E The computer stops and does not proceed to display information or messages except the TOSHIBA logo B Random characters appear on t
135. ommunication switch Otherwise radio waves can potentially affect other equipment thereby causing an accident due to malfunction When using the product in a car check with the automobile dealer if the car has an adequate electromagnetic compatibility EMC Radio waves of the product can potentially hamper safe driving Depending on car model the product can rarely affect car electronic equipment if it is used in a car NOTE Do not use this product in the following places Near a microwave oven or other environment which generates a magnetic field Near any place or equipment that generates static electricity or radio interference Depending on the environment in a place where radio waves cannot reach the product User s Manual xxiii TOSHIBA L10 Series Table of Contents Preface Manual contents 00 200 e eee eee XXX Conventions nci Eee tiet Ge ee ee aes a wee ees xxxi Abbreviations 0 0 000 ccc e xxxi oH PIPER xxxi KeyS L2 nrbERGLLS dS b a ieee Pd due Ws bh eb bbb dd xxxi Key operation 0 00 000 eh xxxii BIA xxxii Messages 0000 ccc ern xxxii Chapter 1 Introduction Equipment checklist 0000 cece eee eee 1 1 Hardware 2 2l2leiacl9RRBARE RD LERRA GG SE ABER LIN 1 1 OMWANC s ai aia e E E e a E E O EE DEEE 1 2 dul Mw 1 3 Special features 00 ee 1 9 EIL P E 1 11 Optlols massa toa aenea ht dee woh daha een eed uibs Rat 1 13 Ch
136. on 90 ms ATX2 Dial tone detect but not U S A call progress detect When used in the Auto Answer mode the SO register must be set with a value of 3 or 4 This ensures W aperson calling your modem will hear a short burst of ringing before the modem answers This confirms that the call has been successfully switched through the network Wi caller identification information which occurs between the first and second ring cadences is not destroyed The preferred method of dialing is to use DTMF tones ATDT as this is faster and more reliable than pulse decadic dialing If for some reason you must use decadic dialing your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand Reverse Dialing standard Number to be dialed 0123456789 Number to program into computer 0987654321 Note that where DTMF dialing is used the numbers should be entered normally The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal Before reporting such occurrences as faults please check the line with a standard Telepermitted telephone and only report a fault if the phone performance is impaired It is recommended that this equipment be disconnected from the Telecom line during electrical storms When relocating the equipment always disconnect the Telecom line c
137. on the power 2 0 cece eee eee I 3 8 Windows XP Setup 2E hy berber ee eee dd oe 3 8 Turning off the power 2 200 eee eee eee 3 9 Shut Down mode Boot mode 0 0000 eee eee 3 9 Hibernation Mode s siss 0 0 cece eee 3 9 Standby Mode ce eh 3 11 Restarting the computer 2002 22 e eee eee eee 3 12 Restoring the preinstalled software 2000 0055 3 13 Operating Basics Using the TouchPad 2000 eee eee eee eee eee 4 1 Using the USB floppy disk drive 2 22005 4 2 Connecting 3 72 floppy disk drive 6 2 00 eee eee 4 2 Disconnecting 3 72 floppy disk drive 0 00 eee eee eee 4 3 Using the optical media drive 0000 eee eee eee 4 3 LOadING dISCS cd pe Xm x a e x nun AYE Re ee eee Ras 4 4 Removing dis6S iode rw de or eg xp cr PR eh ae 4 7 Audio Video controls nnn 4 8 Next and Previous buttons slslleeeeeeeeee 4 8 Play Pause and Stop buttons 000020 cee eee 4 8 User s Manual XXV Table of Contents Writing CDs with the DVD ROM and CD R RW drive 4 9 Important message DVD ROM and CD R RW drive 4 9 Before writing or rewriting llle 4 9 When writing or rewriting 0 0 0 eee ee IR 4 10 Disclaimer DVD ROM and CD R RW drive 45 4 11 Writing CD DVDs with the DVD Super Multi drive 4 11 Important mes
138. onnection before the power connection and reconnect the power first This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM User s Manual TOSHIBA L10 Series General conditions As required by PTC 100 please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork The Telepermit may not be assigned to other parties or other products without Telecom approval A Telepermit artwork for each device is included from which you may prepare any number of Telepermit labels subject to the general instructions on format size and colour on the attached sheet The Telepermit label must be displayed on the product at all times as proof to purchasers and service personnel that the product is able to be legitimately connected to the Telecom network The Telepermit label may also be shown on the packaging of the product and in the sales literature as required in PTC 100 The charge for a Telepermit assessment is 337 50 An additional charge of 337 50 is payable where an assessment is based on reports against non Telecom New Zealand Specifications 112 50 is c
139. ons Otherwise the computer will shut down in Standby Mode If battery power becomes depleted data saved in Standby Mode will be lost Wi You can return to your previous working environment immediately when you turn on the computer W Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature Wi You can use the panel power off feature Starting Hibernation Mode 1 You can also enable Hibernation Mode by pressing Fn F4 Refer to Chapter 5 The Keyboard for details To enter Hibernation Mode follow the steps below 1 Click start 2 Select Turn Off Computer 3 Open the Turn Off Computer dialog box Hibernate is not displayed 4 Press the Shift key The Standby item will change to Hibernate 5 Select Hibernate Automatic Hibernation Mode The computer will enter Hibernate mode automatically when you press the power button or close the Display Screen First however make the appropriate settings according to the steps below 1 Open the Control Panel 2 Open Performance and Maintenance and open Power Options 3 Select the Hibernate tab in the Power Options Properties select the Enable hibernation check box and click the Apply button 4 Click the OK button User s Manual 3 10 Getting Started Data save in Hibernation Mode When you turn off the power in Hibernation Mode the computer takes a moment to save current memo
140. ony location information will also be displayed A check will appear next to the currently selected region and telephony location 3 Select a region from the region menu or a telephony location from the sub menu W When you click a region it becomes the modem s region selection and the New Location for telephony will be set automatically W When you select a telephony location the corresponding region is automatically selected and it becomes the modem s current region setting Properties menu Click the icon with the secondary mouse button to display properties menu on the screen Settings You can enable or disable the following settings AutoRun Mode The Region Select utility starts automatically when you start up the operating system Open the Dialing Properties dialog box after selecting region The dialing properties dialog box will be displayed automatically after you select the region Location list for region selection A submenu appears displaying location information for telephony User s Manual 4 21 Operating Basics Open dialog box if the modem and Telephony Current Location region code do not match A warning dialog box is displayed if current settings for region code and telephony location are incorrect Modem Selection If the computer cannot recognize the internal modem a dialog box is displayed Select the COM port for your modem to use Dialing Properties Select this item to dis
141. ore than once Use either 1 2 or 4 multi speed CD RW discs or high speed 4 to 10 speed discs The write speed of the ultra speed CD RW discs Ultra speed is available on the DVD ROM amp CD R RW drive only is a maximum of 24 speed User s Manual 2 10 The Grand Tour DVDs DVD R discs can be written only once The recorded data cannot be erased or changed DVD RW discs can be recorded more than once DVD RAM discs can be recorded more than once DVD R discs can be written only once The recorded data cannot be erased or changed DVD RW discs can be recorded more than once Formats The drives support the following formats DVD ROM CD DA Photo CD single multi session CD ROM XA Mode 2 Form1 Form2 CD R DVD Video CD Text CD ROM Mode 1 Mode 2 Enhanced CD CD EXTRA CD RW DVD ROM amp CD R RW drive The full size DVD ROM and CD R RW drive module lets you record data to rewritable CDs as well as run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without using an adaptor 1 The read speed is slower at the center of a disc and faster at the outer edge DVD read 8 speed maximum CD read 24 speed maximum CD R write 24 speed maximum CD RW write 24 speed maximum Ultra speed media User s Manual 2 11 The Grand Tour DVD Super Multi drive The full size DVD Super Multi drive module lets you record data to rewritable CD DVDs as well as run either 12 cm 4 72 or 8 cm 3 1
142. orking drive to a slow device like a USB 1 1 hard disk drive or it will fail to write DVD Do not perform any of the following actions Operate the computer for any other function including using a mouse or TouchPad or closing opening the LCD panel Bump or cause vibration to the computer Use the Mode control button and Audio Video control button to reproduce music or voice Open the DVD drive Install remove or connect external devices including the following PC card SD card USB devices external display i LINK devices optical digital devices Please verify your disc after recording important data DVD R R RW disc cannot be written in VR format A maximum of about 2 hours of video data can be written in DVD Video format to DVD R R RW RW disc WinDVD Creator cannot export to DVD Audio VideoCD miniDVD format WinDVD Creator can write DVD RAM RW in VR format but the disc may only play on your computer When writing to DVD disc WinDVD Creator requires 2GB or more over disk space every one hour of video When you make a fully recorded DVD the chapter sequence may not play correctly 3 About Disc Manager WinDVD Creator can edit one play list on a disc WinDVD Creator might show a different a thumbnail than you previously set in CE Consumer Electronics DVD RAM recorder Using the Disc Manager you can edit DVD VR format on DVDRAM DVD VR format on DVD RW and DVD Video format on DVD RW 4
143. ortion to are an analog of the value to be transmitted Voice communications are analog signals ANSI American National Standards Institute An organization established to adopt and define standards for a variety of technical disciplines For example ANSI defined the ASCII standard and other information processing requirements antistatic A material used to prevent the buildup of static electricity User s Manual Glossary 2 Glossary application A group of programs that together are used for a specific task such as accounting financial planning spreadsheets word processing and games ASCII American Standard Code for Information Interchange ASCII code is a set of 256 binary codes that represent the most commonly used letters numbers and symbols async Short for asynchronous asynchronous Lacking regular time relationship As applied to computer communications asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals backup A duplicate copy of files kept as a spare in case the original is destroyed batch file A file that can be executed from the system prompt containing a sequence of operating system commands or executable files binary The base two number system composed of zeros and ones off or on used by most digital computers The right most digit of a binary number has a value of 1 the next a value of 2 then 4
144. osen the screws securing the memory module cover 5 Slide your fingernail or a thin object under the cover and lift it off Memory Module Cover Removing the memory module cover 6 Lift one side of the insulator sheet and fit the module s connectors into the computer s connectors at about a 45 degree angle Press the module carefully to ensure a firm connection Do not touch the connectors on the memory module or on the computer Debris on the connectors may cause memory access problems Y You can install the main memory module in either slot User s Manual 7 5 Optional Devices 7 Push the module down so it lies flat Latches on either side will click into place to secure the module Installing the memory module 8 Seat the cover and secure it with the screws 9 Replace the battery pack as described in Chapter 6 Power and Power Up Modes 10 Turn the power on and make sure the added memory is recognized Open System in the Control Panel and click the General tab Removing a memory module To remove the memory module make sure the computer is in boot mode then 1 Be sure the power is off and all cables are disconnected from the computer 2 Turn the computer upside down and remove the battery and the screws securing the memory module cover 3 Slide your fingernail or a thin object under the cover and lift it off 4 Lift one side of the insulator and push the latc
145. pears for verification However if you select the check box it will not appear in the future e Display selection Press Fn F5 to change the active display device When you press these hot keys a dialog box appears Only selectable devices will be displayed Hold down Fn and press F5 again to change the device When you release Fn and F5 the selected device will change User s Manual 5 3 The Keyboard ha LCD Display Brightness Pressing Fn F6 decreases the display brightness in decrements When you press these hot keys the current setting will be displayed for two seconds by an icon eha LCD Display Brightness Pressing Fn F7 increases the display brightness in increments When you press these hot keys the current setting will be displayed for two seconds by a pop up icon Display clarity increases with the brightness level hea Wireless setting There is no programmed function assigned to Fn F8 on this model F9 t TouchPad Pressing Fn F9 in a Windows environment enables or disables the TouchPad function When you press these hot keys the current setting will change and be displayed as an icon F11 t Press Fn F11 to access the integrated keypad When activated the keys with gray markings on the bottom edge become numeric keypad keys Refer to the Keypad overlay section in this chapter for more information on how to operate these keys The power on default for both settings is off
146. perating properly keyboard floppy disk drives hard disk drive optical media drive display Each device produces different symptoms Wi ls the operating system configuration set properly Check the configuration options B What appears on the display screen Does it display any messages or random characters Print a copy of the screen if you have a printer attached Look up the messages in the software and operating system documentation Check that all connecting cables are correctly and firmly attached Loose cables can cause erroneous or intermittent signals W Do any indicators light Which ones What color are they Do they stay on or blink Write down what you see W Do you hear any beeps How many Are they long or short Are they high pitched or low Is the computer making any unusual noises Write down what you hear Record your observations so you can describe them to your dealer User s Manual 8 2 Troubleshooting Software Hardware The problems may be caused by your software or disk If you cannot load a software package the media may be damaged or the program might be corrupted Try loading another copy of the software If an error message appears while you are using a software package check the software documentation These documents usually include a problem solving section or a summary of error messages Next check any error messages in the operating system documentation If you cannot find a s
147. performance of procedures other than those specified may result in hazardous radiation exposure Wi To prevent direct exposure to the laser beam do not try to open the enclosure Location of the required label SERIAL NO MANUFACTURED COMPLIES WITH FDARADIATION PERFORMANCE STANDARDS 21 CFR SUBCHAPTER J CLASS 1 LASER PRODUCT LASER KLASSE 1 Panasonic Communications Co Ltd 1 62 4 Chome Minoshima Hakata ku Fukuoka Japan User s Manual xiii TOSHIBA L10 Series TOSHIBA SAMSUNG STORAGE TECHNOLOGY DVD ROM amp CD R RW TS L462A W The DVD ROM amp CD R RW drive employs a laser system To ensure proper use of this product please read this instruction manual carefully and retain for future reference Should the unit ever require maintenance contact an authorized service location Wi Use of controls adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure Wi To prevent direct exposure to the laser beam do not try to open the enclosure Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE MANUFACTURED TOSHIBA SAMSUNG STRAGE TECHNOLOGY CORPORATION 580 HORIKAWA CHO SAIWAI KU KAWASAKI SHI 212 0013 JAPAN User s Manual xiv TOSHIBA L10 Series Panasonic DVD ROM amp CD R RW UJDA760 W The DVD ROM amp CD R R
148. play the dialing properties JN If you are using the computer in Japan the Telecommunications Business Law requires that you select Japan region mode It is illegal to use the modem in Japan with any other selection Connecting To connect the modem cable follow the steps below N W The modular cable that comes with the computer must be used to connect a modem Connect the end of the modular cable with the core to the computer Wi ncase of a lightning storm unplug the modem cable from the telephone jack W Do not connect the modem to a digital telephone line A digital line will damage the modem 1 Plug one end of the modular cable into the modem jack 2 Plug the other end of the modular cable into a telephone jack Connecting the internal modem JN Do not pull on the cable or move the computer while the cable is connected 7 If you use a storage device such as an optical drive or hard disk drive l connected to a 16 bit PC Card you might experience the following modem problems W Modem speed is slow or communication is interrupted E Skips may occur in sound User s Manual 4 22 Operating Basics Disconnecting To disconnect the internal modem cable follow the steps below 1 Pinch the lever on the connector in the telephone jack and pull out the connector 2 In the same way pull the cable s other connector out of the computer Wireless LAN The Wireless LAN feature is not available on all mod
149. ques Many problems can be solved simply but a few may require help from your dealer If you find you need to consult your dealer or others be prepared to describe the problem in as much detail as possible User s Manual Troubleshooting Preliminary checklist Consider the simplest solution first The items in this checklist are easy to fix and yet can cause what appears to be a serious problem W Make sure you turn on all peripheral devices before you turn on the computer This includes your printer and any other external device you are using Wi Before you attach an external device turn the computer off When you turn the computer back on it recognizes the new device E Make sure all options are set properly in the setup program B Check all cables Are they correctly and firmly attached Loose cables can cause signal errors Wi Inspect all connecting cables for loose wires and all connectors for loose pins W Check that your floppy disk or CD DVD ROM is correctly inserted and that the floppy disk s write protect tab is correctly set Make notes of your observations and keep them in a permanent error log This will help you describe your problems to your dealer If a problem recurs the log will help you identify the problem faster Analyzing the problem Sometimes the system gives clues that can help you identify why it is malfunctioning Keep the following questions in mind W Which part of the system is not o
150. r Windows DVD Video Player LAN driver Pointing device driver TOSHIBA User s Manual TOSHIBA Console TOSHIBA ConfigFree TOSHIBA Touch and Launch TOSHIBA TouchPad On Off Utility TOSHIBA PC Diagnostic Tool TOSHIBA Zooming Utility Other software may preinstalled dependant on the model purchased Documentation TOSHIBA L10 Series User s Manual TOSHIBA L10 Quickstart Safety Instruction Manual Warranty information Backup Media and Addtional Software B Product Recovery Disc E Tools amp Utilities CD ROM E Additional Software CD indicates an optional part that is dependant on the model purchased If any of the items are missing or damaged contact your dealer immediately User s Manual 1 2 Introduction Features The computer uses TOSHIBA s advanced Large Scale Integration LSI Complementary Metal Oxide Semiconductor CMOS technology extensively to provide compact size minimum weight low power usage and high reliability This computer incorporates the following features and benefits Processor Built in The computer is equipped with an Intel processor Intel Celeron M processor which incorporates a 1 MB level 2 cache memory Intel Celeron M processor 350 1 3GHz or higher Intel Pentium M processor which incorporates a 2 MB level 2 cache memory Intel Pentium M processor 715 1 5GHz or higher Other processors may introduced in the future Memory Slots Up to two 25
151. r a long time avoid direct contact with the metal plate supporting the I O ports It can become hot Wi The surface of the AC adaptor can become hot when in use This condition does not indicate a malfunction If you need to transport the AC adaptor disconnect it and let it cool before moving it E Do not lay the AC adaptor on a material that is sensitive to heat The material could be damaged Pressure or impact damage Do not apply heavy pressure to the computer or subject it to strong impact Excessive pressure or impact can cause damage to computer components or otherwise cause malfunctions User s Manual General Precautions PC Card overheating Some PC Cards can become hot with prolonged use Overheating of a PC Card can result in errors or instability in the PC Card operation Also be careful when you remove a PC Card that has been used for a long time Mobile phones Use of mobile phones can interfere with the audio system Computer operation is not impaired but is recommended that a distance of 30cm be maintained between the computer and a mobile phone in use Central Processing Unit CPU Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions E use of certain peripheral products use of battery power instead of AC power use of certain multimedia games or videos with special effects use of standard telephone lines or low speed network co
152. rd By pressing some keys in combination all the 101 102 key keyboard functions can be executed on the computer The number of keys on your keyboard depends on which country region s keyboard layout your computer is configured with Keyboards for numerous languages are available There are six types of keys typewriter keys keypad overlay function keys soft keys Windows special keys and cursor control keys Typewriter keys The typewriter keys produce the upper and lower case letters numbers punctuation marks and special symbols that appear on the screen There are some differences however between using a typewriter and using a computer keyboard E Letters and numbers produced in computer text vary in width Spaces which are created by a space character may also vary depending on line justification and other factors Wi The lowercase el and the number 1 one are not interchangeable on computers as they are on a typewriter Wi The uppercase O oh and the 0 zero are not interchangeable B The Caps Lock function key locks only the alphabetic characters in uppercase while the shift lock on a typewriter places all keys in the shifted position B The Shift keys the Tab key and the BkSp backspace key perform the same function as their typewriter counterparts but also have special computer functions User s Manual The Keyboard F1 F12 function keys The function keys not to be confused with F
153. rdinances or regulations Use only batteries recommended by TOSHIBA as replacements E Do not touch the latch while holding the computer Or you may get injured by the dropped battery by unintentional release of the latch Please do not push the power button before installing the battery pack Turn the computer s power off Disconnect all cables connected to the computer Insert the battery pack The Battery Release Latch 2 clicks into place Secure the Battery Release Lock 1 to ensure the battery is locked into place Later when you want to remove the battery you must disengage this lock first oh gt Battery Release Latch 2 Battery Release ___ Lock 1 MINIL c VIII Securing the battery pack e Refer to Removing the battery pack section in Chapter 6 Power and J Power Up Modes for removing the battery pack User s Manual 3 5 Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power It is also the fastest way to get started because the battery pack will need to be charged before you can operate from battery power The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz For details on using the AC adaptor to charge the battery pack refer to Chapter 6 Power and Power Up Modes Use only the AC adaptor supplied as an accessory Other AC adaptors have differe
154. rer Favorites menu Wi To display the list of currently open windows and change the active window Also TOSHIBA Touch and Launch provides the following functions by customizing the settings Wi To open a file stored in a predefined folder B6 To quickly launch your frequently used applications which have been registered To run TOSHIBA Touch and Launch click start select All Programs followed by TOSHIBA followed by Utilities and then click Touch and Launch User s Manual 1 12 Introduction Options You can add a number of options to make your computer even more powerful and convenient to use Refer to Chapter 7 Optional Devices for details The following options are available Memory expansion Battery pack AC Adaptor USB Floppy Disk Kit A 256 or 512 MB memory module PC2100 PC2700 DDR can easily be installed in the computer PC2700 works the same as PC2100 An additional battery pack can be purchased from your TOSHIBA dealer Use it as a spare or replacement Battery pack 4300mAh If you use your computer at more than one site frequently it may be convenient to purchase an additional AC adaptor for each site so you will not have to carry the adaptor with you A 3 floppy disk drive accommodates 1 44 megabyte or 720 kilobyte floppy disk It connects to a USB port You cannot format 720 kilobyte floppy disks on Windows XP but you can use previously formatted disks User s Manual TO
155. rge scale integration User s Manual Glossary 8 Glossary main board See motherboard megabyte MB A unit of data storage equal to 1024 kilobytes See also kilobyte megahertz A unit of wave frequency that equals 1 million cycles per second See also hertz menu A software interface that displays a list of options on the screen Also called a screen microprocessor A hardware component contained in a single integrated circuit that carries out instructions Also called the central processing unit CPU one of the main parts of the computer mode A method of operation for example the boot mode Standby Mode or the Hibernation Mode modem Derived from modulator demodulator a device that converts modulates digital data for transmission over telephone lines and then converts modulated data demodulates to digital format where received monitor A device that uses rows and columns of pixels to display alphanumeric characters or graphic images See also CRT motherboard A name sometimes used to refer to the main printed circuit board in processing equipment It usually contains integrated circuits that perform the processor s basic functions and provides connectors for adding other boards that perform special functions Sometimes called a main board MP3 An audio compression standard that enables high quality transmission and real time playback of sound files N non system disk A formatted floppy disk you can
156. ry data to the hard disk During this time the Disk indicator will light After you turn off the computer and memory is saved to the hard disk turn off the power to any peripheral devices Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge Standby Mode If you have to interrupt your work you can turn off the power without exiting from your software Data is maintained in the computer s main memory When you turn on the power again you can continue working right where you left off BW When the AC adaptor is connected the computer will go into Standby Mode according to the settings in the Power Options Wi 7o restore operation from Standby Mode press the power button or press any key The latter action works only if Wake up on Keyboard is enabled in HW Setup E fthe computer automatically enters Standby Mode while a network application is active the application might not be restored when the computer wakes up from Standby E To prevent the computer from automatically entering Standby Mode disable Standby in the Power Options That action however will nullify the computer s Energy Star compliance E Before entering Standby Mode be sure to save your data E Do not install or remove a memory module while the computer is in Standby Mode The computer or the module could be damaged W Do not remove the battery pack while the computer is in Standby Mode unless the comput
157. s quickly replaced by No CARRIER Character display becomes garbled during a communication You cannot receive an incoming call Problem Cannot access LAN Wireless LAN If the following procedures do not restore LAN access consult your LAN administrator For more information on wireless communication refer to Chapter 4 Operating Basics i Problem Cannot access Wireless LAN Procedure Make sure the tone or pulse selection in your communications application is set correctly You can also use the ATD command The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval Try lengthening this time interval Check the error control setting in your communications application You can also use the AT N command In data transmission make sure the parity bit and stop bit settings correspond with those of the remote computer Check the flow control and communication protocol Check the rings before auto answer setting in your communications application You can also use the ATSO command If problems persist contact your dealer Procedure Check for a firm cable connection between the LAN jack and the LAN hub If problems persist consult your LAN administrator Procedure Make sure the computer s wireless communication switch is set to on If problems persist contact your LAN administrator The Wireless LAN feature is not avai
158. s LAN Access Point When roaming between different access points the station can dynamically switch to another channel if required For Wireless LAN cards installed in wireless clients that operating in a peer to peer mode the card will use the default channel 10 In a Wireless LAN Access Point the Wireless LAN card will use the factory set default channel printed in bold unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device User s Manual C TOSHIBA L10 Series Appendix D AC Power Cord and Connectors The power cord s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country region in which it is used All cords must meet the following specifications Length Minimum 2 meters Wire size Minimum 0 75 mm Current rating Minimum 2 5 amperes Voltage rating 125 or 250 VAC depending on country region s power standards Certification agencies U S and Canada UL listed and CSA certified No 18 AWG Type SVT or SPT 2 two conductor Australia AS Japan DENANHO User s Manual AC Power Cord and Connectors Europe Austria Belgium Denmark Finland France Germany OVE CEBEC DEMKO SETI UTE VDE Italy IMQ The Netherlands KEMA Norway NEMKO Sweden SEMKO Switzerland SEV United Kingdom BSI In Europe power cords must be VDE type HO5VVH2 F a
159. s for current information and support Where to write If you are still unable to solve the problem and suspect that it is hardware related write to TOSHIBA at the nearest location listed on the below User s Manual 8 16 Troubleshooting Outside of Europe Australia TOSHIBA Australia Pty Ltd Information Systems Division 84 92 Talavera Road North Ryde N S W 2113 Sydney Canada TOSHIBA of Canada Ltd 191 McNabb Street Markham Ontario L3R 8H2 China TOSHIBA Personal Computer amp Network Shanghai Co Ltd 43F Hongkong new world tower No 300 Huai Hai Zhong Road Shanghai P R China 200021 Singapore TOSHIBA Singapore Pte Ltd 438B Alexandra Road 06 01 Alexandra Technopark Singapore 119968 United States of America TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 USA In Europe Germany amp Austria TOSHIBA Europe I E GmbH Gesch ftsbereich Deutschland sterreich Hammfelddamm8 D 41460 Neuss Germany France TOSHIBA Syst ms France S A 7 Rue Amp re B P 131 92804 Puteaux Cedex Netherlands TOSHIBA Information Systems Benelux B V Rivium Boulevard 41 2909 LK Capelle a d IJssel Spain TOSHIBA Information Systems ESPANA Parque Empresarial San Fernando Edificio Europa la Planta Escalera A 28830 Madrid United Kingdom TOSHIBA Information Systems U K Ltd TOSHIBA Court Weybridge Business Park Addlesto
160. sage DVD Super Multi drive 4 11 Disclaimer DVD Super Multi drive 2 005 4 11 Before writing or rewriting 0002 cece eee eee 4 12 When writing or rewriting 020000 cece eee 4 14 RecordNow Basic for TOSHIBA 0 0000 e eee 4 15 DLA for TOSHIBA 2 tee 4 16 InterVideo WinDVD Creator Platinum 0005 4 17 Media Care icse ie a eee dere RR ee a ee hdmi n 4 19 CD DVDS cco ack ied nbd eee See eee he eee ee at 4 19 Floppy disks 0 000 cece eh 4 19 Sound System ices et hee eee eee ewe eee ae eee eee 4 20 Volume control auauua aeaaaee 4 20 Microphone level 2 22 pera pl elec ede eee 4 20 Lubp Ju M RE TIT 4 20 Region selection 0 0000 eee 4 21 Properties MENU 6 ee ee eee ee 4 21 Settings fc eae Pee how add beds Re eee ra bagel enixe 4 21 Modem Selection 0 0 cece tee 4 22 Dialing Properties nannan aana aaa 4 22 Connecting 0 etaan na dei len 4 22 Disconnecting ercas tdi pa eee eae ERR ped AE Rs 4 23 Wireless LAN i e 6 ice ene ce eae ewe ees eee eee we 4 23 Securty i elmeLleetbR RRIRSu LA Rege ee RENDpNDbReehe ne 4 23 Wireless communication switch 00 0 0 0 eee ee eee 4 23 Wireless communication indicator sls 4 24 LAN ubere anu eee EDEN EE E UM Sa Els 4 24 LAN cable types lsissslssslseesl sse 4 24 Connecting LAN cable 0 0000 e eee 4 2
161. ser s Manual iv TOSHIBA L10 Series Canadian Regulatory Information Canada Only This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications Note that Canadian Department of Communications DOC regulations provide that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment This Class B digital apparatus meets all requirements of the Canadian Interference Causng Equipment Regulations Cet appareil num rique de la class B respecte toutes les exgences du R glement sur le mat riel brouileur du Canada Modem warning notice Conformity Statement The equipment has been approved to Commission Decision CTR21 for pan European single terminal connection to the Public Switched Telephone Network PSTN However due to differences between the individual PSTNs provided in different countries regions the approval does not of itself give an unconditional assurance of successful operation on every PSTN network termination point In the event of problems you should contact your equipment supplier in the first instance Network Compatibility Statement This product is designed to work with and is compatible with the following networks It has been tested to and found to conform with the additional requirements conditiona
162. set up procedures If you are using Fast Ethernet LAN 100 megabits per second 100BASE TX be sure to connect with a CAT5 cable or higher You cannot use a CAT3 cable If you are using Ethernet LAN 10 megabits per second 10BASE T you can connect with a CAT3 or higher User s Manual 4 24 Operating Basics Connecting LAN cable To connect the LAN cable follow the steps below 1 Turn off the power to the computer and to all external devices connected to the computer 2 Plug one end of the cable into the LAN jack Press gently until you hear the latch click into place Connecting the LAN cable 3 Plug the other end of the cable into a LAN hub connector Check with your LAN administrator before connecting to a hub Disconnecting LAN cable To disconnect the LAN cable follow the steps below 1 Pinch the lever on the connector in the computer s LAN jack and pull out the connector 2 Disconnect the cable from the LAN hub in the same manner Check with your LAN administrator before disconnecting from the hub Cleaning the computer To help ensure long trouble free operation keep the computer free of dust and use care with liquids around the computer Wi Becareful not to spill liquids into the computer If the computer does get wet turn the power off immediately and let the computer dry completely before you turn it on again Wi Clean the computer using a slightly damp with water cloth You can us
163. t E Cover one module is preinstalled Refer to the Memory expansion section in Chapter 7 Optional Devices Wireless LAN Cover This cover protects the Wireless LAN bay and if installed the Wireless LAN card Not all models support this feature Cooling Vents Cooling vents help prevent the CPU from overheating User s Manual 2 5 The Grand Tour Front with the display open This section shows the front of the computer with the display open Refer to the appropriate illustration for details To open the display slide the display latch on the front of the display and lift up Position the display at a comfortable viewing angle s Display Screen System Keyboard Indicators AL Se Hinge Power Button TouchPad Control Audio Video Buttons Control Buttons TouchPad System Indicators The front of the computer with the display open Power Button Turns the computer on and off as well as puts it into Hibernation mode and wakes it up from said mode System Indicators LEDs let you monitor the status of various computer functions Battery charge Power Wireless activity HDD activity CapsLock status and NumLock status Details are given in the System indicators section Audio Video Control Previous I lt button Plays the previous track Buttons chapter data Next 1 button Plays the next track chapter data Play pause I button Begins or pauses play
164. t in HDD ODD indicators are off If you turn off the power while a disk disc is being accessed you can lose data or damage the disk disc 3 Click start then click Turn Off Computer From the Turn Off Computer menu select Turn Off 4 Turn off the power to any peripheral devices Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge Hibernation Mode A The hibernation feature saves the contents of memory to the hard disk when the computer is turned off The next time the computer is turned on the previous state is restored The hibernation feature does not save the status of peripheral devices E Save your data While entering Hibernation Mode the computer saves the contents of memory to the HDD However for safety sake it is best to save your data manually Wi Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed Wait for the Disk indicator to go out E Do not install or remove a memory module while the computer is in Hibernation Mode Data will be lost User s Manual 3 9 Getting Started Benefits of Hibernation Mode The Hibernation Mode feature provides the following benefits E Saves data to the hard disk when the computer automatically shuts down because of a low battery Jq For the computer to shut down in Hibernation Mode the hibernation J feature must be enabled in the Hibernate tab in Power Opti
165. t lets you run either 12 cm 4 72 or 8 cm 3 15 disks without using an adaptor Refer to the Fixed Optical media drive section in this chapter for technical specifications on each drive and to Chapter 4 Operating Basics for information on using the drive and caring for disks The following drives are available BW DVD ROM amp CD R RW drive W DVD Super Multi drive W DVD Super Multi drive Supporting Double Layer Press this to open the ODD tray In the event that the disc drive becomes inexplicably locked or stops responding press this button to force a manual ejection of the ODD tray The ODD indicator glows amber when the computer accesses the optical disc drive User s Manual 2 3 The Grand Tour Backside The following figure shows the computer s back panel It differs depending on the model DC IN 19V Jack USB Port Modem Jack EE E Video Out Jack LAN Jack The backside of the computer NS Universal Serial Bus A Universal Serial Bus port is on the right side USB 2 0 port Refer to the Left side section for details DC IN 19V Jack The AC adaptor connects to this socket Use Les only the model of AC adaptor that comes with the computer Using the wrong adaptor can damage your computer C Video Out Jack Plug an S Video cable into this jack for video out The S Video cable carries video signals Not available on all models 3 Modem Jack In areas where an internal modem is install
166. tect them and keep them clean If a floppy disk is dirty do not use cleaning fluid Clean it with a soft damp cloth Do not slide back the floppy disk s protective metal covering or touch the floppy disk s magnetic surface Fingerprints may prevent the floppy disk drive from reading data from the floppy disk Data may be lost if the floppy disk is twisted bent or exposed to direct sunlight extreme heat or cold Do not place heavy objects on your floppy disks Do not eat smoke or use erasers near your floppy disks Foreign particles inside the floppy disk s jacket can damage the magnetic surface Magnetic energy can destroy the data on your floppy disks Keep your floppy disks away from speakers radios television sets and other sources of magnetic fields User s Manual 4 19 Operating Basics Sound System This section describes audio controls including sound levels and power management Volume control The Volume Control utility lets you control the audio volume in Windows for both playback and recording Wi To launch Volume Control for playback click start point to All Programs point to Accessories point to Entertainment and click Volume Control W To launch Recording Control click Options point to Properties choose Recording and click OK Wi To view details of the Volume Control click Help on the Volume Control Microphone level To change the microphone gain follow the steps below
167. the computer Restoring the preinstalled software All users should be sure to read the section Windows XP setup Getting Started Setting up your work space Establishing a comfortable work site is important for you and your computer A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands wrists or other joints Proper ambient conditions should also be maintained for the computer s operation This section discusses the following topics General conditions Placement of the computer Seating and posture Lighting W Work habits General conditions In general if you are comfortable so is your computer but read the following to make sure your work site provides a proper environment B Make sure there is adequate space around the computer for proper ventilation W Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible Wi The temperature should be 5 to 35 degrees Centigrade 41 to 95 degrees Fahrenheit and the relative humidity should be 20 to 80 percent Wi Avoid areas where rapid or extreme changes in temperature or humidity may occur W Keep the computer free of dust moisture and exposure to direct sunlight E Keep the computer away from heat sources such as electric heaters Wi Do not use the computer near liquids or corrosive chemicals E Do not place the computer near objects that create stro
168. the computer and briefly explains how they function Chapter 3 Getting Started provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area User s Manual Preface Chapter 4 Operating Basics includes instructions on using the following devices TouchPad optional USB floppy disk drive Audio Video controls Sound System optical media drives modem wireless communication and LAN It also provides tips on care of the computer floppy disks and CD DVDs Chapter 5 The Keyboard describes special keyboard functions including the keypad overlay and hot keys Chapter 6 Power and Power Up Modes gives details on the computer s power resources and battery save modes Chapter 7 Optional Devices describes the optional hardware available Chapter 8 Troubleshooting provides helpful information on how to perform some diagnostic tests and suggests courses of action if the computer doesn t seem to be working properly The Appendices provide technical information about your computer The Glossary defines general computer terminology and includes a list of acronyms used in the text The ndex quickly directs you to the information contained in this manual Conventions This manual uses the following formats to describe identify and highlight terms and operating procedures Abbreviations On first appearance and whenever necessary for clarity abbreviations are
169. the previous track chapter or data e 3l If Random is selected in Windows Media Player selecting Next or Previous advances to a random selection Play Pause and Stop buttons Press on the button to select the desired function Play Pause Press the gt H button to begin or pause play Stop Press the W button to stop play Audio Video Control buttons User s Manual 4 8 Operating Basics Writing CDs with the DVD ROM and CD R RW drive i Depending on the type of drive installed you may be able to write CDs The DVD ROM and CD R RW drive lets you read DVD ROMs and CDs as well as write CD R RW Observe the precautions in this section to ensure the best performance for writing CDs For information on loading and unloading CDs refer to the Using optical media drive section CD R discs can be written to only once CD RW discs can be rewritten many times Important message DVD ROM and CD R RW drive Before you write or rewrite to DVD ROM and CD R RW disc read and follow all setup and operating instructions in this section If you fail to do so the DVD ROM and CD R RW drive may not function properly and you may fail to write or rewrite lose data or incur other damage Before writing or rewriting Please observe the following points when you write or rewrite the data B We recommend the following manufacturers of CD R and CD RW media Media quality can affect write or rewrite success rates CD R TAIYO
170. ther serial interface Refers to a type of information exchange that transmits information sequentially one bit at a time Contrast Parallel interface SIO Serial Input Output The electronic methodology used in serial data transmission Soft key Key combinations that emulate keys on the IBM keyboard change some configuration options stop program execution and access the numeric keypad overlay software The set of programs procedures and related documentation associated with a computer system Specifically refers to computer programs that direct and control the computer system s activities See also hardware stop bit One or more bits of a byte that follow the transmitted character or group codes in asynchronous serial communications subpixel Three elements one red one green and blue RGB that make up a pixel on the color LCD The computer sets subpixels independently each may emit a different degree of brightness See also pixel synchronous Having a constant time interval between successive bits characters or events User s Manual Glossary 11 Glossary system disk A disk that has been formatted with an operating system For MS DOS the operating system is contained in two hidden files and the COMMAND COM file You can boot a computer using a system disk Also called an operating system disk T terminal A typewriter like keyboard and CRT display screen connected to the computer for data input output
171. u User s Manual Glossary 10 Glossary Radio frequency interference RFI shield A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference All computer equipment generates radio frequency signals The FCC regulates the amount of signals a computing device can allow past its shielding A Class A device is sufficient for office use Class B provides a more stringent classification for home equipment use TOSHIBA portable computers comply with Class B computing device regulations Random Access Memory RAM High speed memory within the computer circuitry that can be read or written to restart Resetting a computer without turning it off also called warm boot or soft reset See also boot RGB Red green and blue A device that uses three input signals each activating an electron gun for a primary additive color red green and blue or port for using such a device See also CRT RJ11 A modular telephone jack RJ45 A modular LAN jack ROM Read Only Memory A nonvolatile memory chip manufactured to contain information that controls the computer s basic operation You cannot access or change information stored in ROM S SCSI Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices serial communications A communications technique that uses as few as two interconnecting wires to send bits one after ano
172. ulated using two keys instead of one on the larger keyboard Your software may require you to use keys that the keyboard does not have Pressing the Fn key and one of the following keys simulates the enhanced keyboard s functions User s Manual 5 2 The Keyboard Hot keys Hot keys let you enable or disable certain features of the computers i6 6 Sound mute Pressing Fn Esc in a Windows environment turns sound on or off When you press these hot keys the current setting will change and be displayed as an icon i es Instant security Press Fn F1 to blank the screen to prevent others from accessing your data To restore the screen and original settings press any key or press the TouchPad If a screensaver password is registered a dialog box will appear Enter the screensaver password and click OK If no password is set the screen will be restored when you press any key or press the TouchPad F2 t Power save mode Pressing Fn F2 opens Power Option Properties You can check the power status or configure power saving settings H ea Standby When you press Fn F3 the computer enters Standby Mode To avoid entering Standby Mode unexpectedly a dialog box appears for verification However if you select the check box it will not appear in the future F4 Hibernation When you press Fn F4 the computer enters Hibernation Mode To avoid entering Hibernation Mode unexpectedly a dialog box ap
173. video Log in with Administrator rights to use WinDVD Creator Make sure that your computer is running on AC power when using WinDVD Creator Operate the computer under the power scheme Always ON Do not use power saving features While you are editing DVD you can display previews However if another application is running the preview might not display properly WinDVD Creator cannot show video on the external monitor when in simultaneous mode WinDVD Creator cannot edit or play copy protected content Do not change display settings while using WinDVD Creator Do not enter standby hibernation mode while using WinDVD Creator Do not operate WinDVD Creator immediately after turning on the computer Please wait until all Disc Drive activity has stopped When recording to a DV Camcorder to ensure you capture all of your data let the camcorder record for a few seconds before you begin recording your actual data CD recorder JPEG functions DVD Audio mini DVD and Video CD functions are not supported in this version While recording video to DVD or tape please close all other programs Do not run software like a screen saver because it can put a heavy load on the CPU Do not run communication applications like a modem or a LAN User s Manual 4 17 Operating Basics 2 Before recording the video to DVD When you record to DVD disc please use only discs recommended by the Drive manufacturer Do not set the w
174. wer off 0 0 0 cece eee 6 10 Extending battery life 0 eee 6 10 Replacing the battery pack 00 eee eee eee eee 6 11 Removing the battery pack 00 0020 c eee 6 11 Installing the battery pack lisse 6 12 Power up modes lesseeeee nnn 6 13 Windows Utilities ore roErOTL RU DERE eee 6 13 HoOUKGyS Ue bac eoe Ge casts iE d etn idu ps EE 6 13 Panel power oOfffon 0022 0c eee eee eee 6 13 System Auto Off icio a ha eee 6 13 User s Manual xxvii Table of Contents Chapter7 Optional Devices PC calda du dau daa de Ce dana da RERO a ON o pa aA S 7 2 Inserting a PC Card 2 0 24 c ec eee eee eee 7 2 Removing a PC Card 0 0 cee 7 3 Memory expansion 2000 e eee eee eee 7 4 Installing a memory module 0 0 0 e eee eee 7 5 Removing a memory module 0 0 e eee ee eee 7 6 Additional battery pack 200s eee eee 7 7 Additional AC adaptor 200 cece eee 7 7 USB floppy disk drive 0 0 ccc eee 7 8 External monitor 0 0 0 cece eee 7 8 DP 7 9 Changing the resolution 2 0 0 cece esee 7 10 Security lock nda Sei td oiu atus duo Sudan ae 7 10 Chapter8 Troubleshooting Problem solving procesSsS 0 0 00 cece eee eee eee nnn 8 1 Preliminary checklist llle 8 2 Analyzing the problem 00 00 cece eee e eee eeee 8 2 Hardware and system checklist 0
175. y cuts off power to the internal display when there is no keyboard input for a time specified Power is restored when any key is pressed To specify the time click start Control Panel Performance and Maintenance Power Options At Power Schemes tab you can select the time for Turn off monitor This feature automatically cuts off power to the hard disk drive when it is not accessed for a time specified Power is restored when the hard disk is accessed To specify the time click start Control Panel Performance and Maintenance Power Options At Power Schemes tab you can select the time for Turn off hard disks User s Manual 1 9 Introduction System Automatic Standby Hibernation Intelligent Power Supply Battery Save Mode Panel Power On Off Low Battery Automatic Hibernation Hibernation Standby This feature automatically shuts down the system in Standby Mode or Hibernation Mode when there is no input or hardware access for a time specified To specify the time click start Control Panel Performance and Maintenance Power Options At Power Schemes tab you can select the time for System standby or System hibernates A microprocessor in the computer s intelligent power supply detects the battery s charge and calculates the remaining battery capacity It also protects electronic components from abnormal conditions such as voltage overload from an AC adaptor To monitor remaining battery capacity
176. y may not charge right away under the following conditions Wi The battery is extremely hot or cold If the battery is extremely hot it might not charge at all To ensure the battery charges to its full capacity charge the battery at room temperature of 10 to 30 C 50 to 88 F W The battery is nearly completely discharged Leave the AC adaptor connected for a few minutes and the battery should begin charging The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions E The battery has not been used for a long time W The battery has completely discharged and been left in the computer for a long time W A cool battery is installed in a warm computer In such case follow the steps below 1 Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off 2 Plug in the AC adaptor 3 Charge the battery until the Battery indicator glows green Repeat these steps two or three times until the battery recovers normal capacity Leaving the AC adaptor connected will shorten battery life At least once a month run the computer on battery power until the battery is fully discharged then recharge the battery User s Manual 6 8 Power and Power Up Modes Monitoring battery capacity i Remaining battery power can be monitored in the taskbar and in the Windows Power Options control pan
177. y observe the following advisories Danger Indicates an imminently hazardous situation which could result in death or serious injury if you do not follow instructions Warning Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions Caution Indicates a potentially hazardous situation which if not avoided may result in moderate or minor injury or property damage Note Provides important information Danger 1 Never try to dispose of the battery pack by burning or expose it to a heating device such as a microwave oven The battery pack could explode and cause bodily injury 2 Never try to disassemble repair or otherwise tamper with a battery pack The battery pack will overheat and ignite Leakage of caustic alkaline solution or other electrolytic substances will cause fire or injury possibly resulting in death or serious injury 3 Never short circuit the battery pack by contacting the terminals with a metal object A short circuit can cause fire or otherwise damage the battery pack and possibly cause injury To avoid accidental short circuit always wrap the battery pack in plastic and cover the terminals with electrical tape when storing or disposing of the battery pack 4 Never puncture the battery pack with a nail or other sharp object Never strike it with a hammer or other object Never step on it 5 Never try to charge the battery pack in any man
178. you close the display panel When you open the panel power turns on in Standby Mode or Hibernation Mode but not in boot mode 1 If the panel power off function is enabled and you use Shut down Windows do not close the display until the shut down function is completed System Auto Off This feature turns the system off automatically if it is not used for a set duration The system shuts down in Standby Mode or Hibernation Mode in Windows User s Manual TOSHIBA L10 Series Chapter 7 Optional Devices Optional devices can expand the computer s capabilities and its versatility This chapter describes connection or installation of the following devices which are available from your TOSHIBA dealer Cards memory W PC card B Memory expansion Power devices E Additional battery pack B Additional AC adaptor Peripheral devices B USB floppy disk drive B External monitor E TV Other B Security lock User s Manual Optional Devices PC card The computer is equipped with a PC Card expansion slot that can accommodate one 5 mm Type II card Any PC Card that meets industry standards manufactured by TOSHIBA or other vendor can be installed The slot supports 16 bit PC Cards including PC Card 16 s multifunction card and CardBus PC Cards CardBus supports the new standard of 32 bit PC Cards The bus provides superior performance for the greater demands of multimedia data transmission Inserting a PC

TOSHIBA L10 Series

Contents

Download Pdf Manuals

Related Search

Related Contents