Home

Quick Start Guide WI-I/O 9-L-T Wireless I/O Transmitter Unit

image

Contents

1. Weidmuller Inc will replace the product with an equivalent product if an equivalent product is available This warranty does not extend to Failures caused by the operation of the equipment outside the particular product s specification or Use of the module not in accordance with this User Manual or Abuse misuse neglect or damage by external causes or Repairs alterations or modifications undertaken other than by an authorized Service Agent Weidmuller Inc s liability under this warranty is limited to the replacement or repair of the product This warranty is in lieu of and exclusive of all other warranties This warranty does not indemnify the purchaser of products for any consequential claim for damages or loss of operations or profits and Weidmuller Inc is not liable for any consequential damages or loss of operations or profits resulting from the use of these products Weidmuller Inc is not liable for damages losses costs injury or harm incurred as a consequence of any representations warranties or conditions made by Weidmuller Inc or its representatives or by any other party except as expressed solely in this document WI I O 9 L Transmitter Unit Quick Start v1 7 page 8 of 8
2. 1 accuracy 10 ohm input impedance 1 J K or T type thermocouple with on board cold junction compensation Digital inputs Analog inputs Thermocouple inputs Cold junction compensation accuracy 1 over ambient temp range 40 to 70 C 1 9 30 VDC 1 Amp CSA certified Class 2 power supply For use in Class 1 Div 2 explosive areas the power supply must be approved for Class 1 Div 2 use WENGE Explosion hazard do not disconnect while circuit is live unless area is known to be non hazardous 1 1 Watt Frequency Hopping Spread Spectrum FHSS Transmitter 902 928 MHz Actual frequency range depends on country Power supply Transmitter Frequency WI I O 9 L Transmitter Unit Quick Start v1 7 page 7 of 8 WI I O 9 L Transmitter Unit Quick Start Guide Document information Quick Start Guide WI I O 9 L T Wireless I O Transmitter Unit Contact details Address 2 821 Southlake Blvd Richmond VA 23832 Telephone gt 800 849 9343 Fax gt 804 897 4136 Email gt info weidmuller com Website gt www wireless weidmuller com Limited lifetime warranty disclaimer and limitation of remedies Weidmuller Inc products are warranted to be free from manufacturing defects for the serviceable lifetime of the product The serviceable lifetime is limited to the availability of electronic components If the serviceable life is reached in less than three years following the original purchase from Weidmuller Inc
3. and any other certification designations Industry Canada Wireless I O Module RSS 119 This device has been type accepted for operation by Industry Canada in accordance with RSS 119 of the Industry Canada rules See the label on the unit for the specific Industry Canada certification number and any other certification designations NOTE Any changes or modifications not expressly approved by Weidmuller Inc could void the user s authority to operate this equipment To operate this equipment legally the user must obtain a radio operating license from the government agency This is done so the government can coordinate radio users in order to minimize interference Safety information FCC Notice This device complies with Part 15 247 of the FCC Rules Operation is subject to the following two conditions gt This device may not cause harmful interference and gt This device must accept any interference received including interference that may cause undesired operation NOTE This equipment is suitable for use in Class 1 Division 2 groups A B and C or non hazardous locations only Unit specifications input output Number Additional information 2 Dry contact digital inputs slow pulsed at 10Hz All inputs are suitable for voltage free contacts e g mechanical switches or NPN transistor devices e g electronic proximity switches NOTE PNP transistor device inputs are NOT suitable 1 0 20mA differential input 16 bit resolution 0
4. detected in unit TX Led Flashes Transmitting Message PG LED on Configuration Cable Connected Input LED ON Input LEDS i e D1 D2 SP AZ light when the corresponding input is active D1 Digital Input 1 is active Low D2 Digital Input 2 is active SP Analog Setpoint is active AZ Analog Input is zero mA All LEDs medium flash Medium speed flash 1 6HZ indicates the module is half way through the configuration process Medium flash also happens when you set the rotary switch to position 0 when powering on the unit Antenna installation 1m minimum Collinear antenna Objects e g walls Weatherproof connectors e g 3M 23 tape etc Surge protector arrestor optional Stress relief loop ELPRO Unit You must provide good ground connection to the mast unit and surge arrestor protector Earth Stake A Vou must install the aerial above all local obstructions WI I O 9 L Transmitter Unit Quick Start v1 7 page 5 of 8 WI I O 9 L Transmitter Unit Quick Start Guide Resetting vour unit to factorv defaults To reset the default factorv configuration 1 Set the RSSI rotary switch to position 0 using a screwdriver 2 Power on the WI I O 9 L T transmitter 3 The WI I O 9 L T transmitter flashes all LEDs at medium flash i e 1 6 Hz NOTE If the LEDs do not flash you must repeat steps 1 and 2 until the LEDs flash before continuing 4 Set the RSSI rotary switch to another position i e posit
5. on again If you exceed the 60 seconds you must restart the linking process from step 1 7 You can now bench test your configuration before deploying WI I O 9 L Transmitter Unit Quick Start v1 7 page 6 of 8 WI I O 9 L Transmitter Unit Quick Start Guide Safetv information Thank you for selecting the WI I O 9 L T transmitter for your telemetry needs We trust it will give you many years of valuable service To ensure your WI I O 9 L T transmitter enjoys a long life double check ALL your connections with the user s manual before powering on the unit UZASNI Incorrect termination of supply wires may cause internal damage and will void warranty Exposure to RF energy is an important safety consideration The FCC has adopted a safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated equipment as a result of its actions in Docket 93 62 and OET Bulletin 65 Edition 97 01 FCC Notice when used in USA WI I O 9 L T Module Additional information 15 This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part15 of the FCC rules Code of Federal Regulations 47CFR Part 15 Operation is subject to the condition that this device does not cause harmful interference 90 This device has been type accepted for operation by the FCC in accordance with Part90 of the FCC rules 47CFR Part 90 See the label on the unit for the specific FCC ID
6. Quick Start Guide WIl 1 O 9 L T Wireless I O Transmitter Unit WI I O 9 L T QuickStart v1 7 WI I O 9 L Transmitter Unit Quick Start Guide About this document This document is the WI l O 9 L T Wireless I O Transmitter Unit Quick Start Guide and contains the following sections Section Read this section if you want to Basic steps for using your unit Learn the basic steps for installing and using your unit Factory default configuration Understand how the transmitter sends information to the receiver Unit components Understand the different parts of your unit Antenna installation Learn how to install an antenna with your unit Resetting factory defaults Reset your unit to the original factory default settings Linking transmitter and receiver units Link your units to work as a dedicated pair Safety information Understand important safety information related to your unit NOTE You must read this information before installing your unit Specifications Know technical information about your unit For more information see the next sections Basic steps for using your unit This document describes how to configure your unit using the default factory configuration that lets you easily setup your network as a simple send receive network using a dedicated pair of transmitter and receiver units The basic steps for using your unit are 1 Connect the antenna power supply and transducer signals using the instruction
7. ion 1 within 5 seconds 5 Set the RSSI rotary switch to position O within another 5 seconds 6 The WI I O 9 L transmitter lights all LEDs for 2 seconds before returning to normal operation NOTE If the LEDs do not light for 2 seconds you must repeat the process from step 1 until the LEDs light before continuing 7 You can now link the transmitter and receiver units Linking your transmitter and receiver units You must reset the transmitter unit to factory defaults to disable encryption before linking the transmitter and receiver units For more information see the previous section NOTE You must complete the linking process in 60 seconds To link the transmitter and receiver units 1 2 3 Press and hold down the RSSI Pushbutton on the receiver Power on the receiver while holding down the RSSI Pushbutton Release the RSSI Pushbutton as soon as the Receiver LEDS flash within 5 seconds of powering the receiver The receiver will flash all LEDs for a maximum 60 seconds while it tries to link to the transmitter Power on the transmitter The transmitter sends a special Link message to allow the receiver to recognise the transmitter When the units link the receiver lights all LEDs for 2 seconds before returning to normal operation NOTE If the receiver LEDs continue flashing within the 60 seconds the units are not linked and you should retry the linking process by powering the transmitter off and
8. s in this document Power supply and transducer connection is described in the section Unit components and connections Antenna connection is described in the section Antenna installation For more information see the WI I O 9 L x Install Manual Reset the transmitter and receiver units to the factory default configurations Link the transmitter and receiver units to work as a dedicated pair Bench test your configuration before deploying NOTE You can also configure your network using a user defined customised configuration that lets you set specific information about your network For more information on setting a user defined customised configuration see the WI I O 9 L x User Manual on the enclosed CD Factory default configuration When you configure the units using the configuration in this document the inputs from the transmitter are sent to the outputs at the receiver as follows l 1 O 9 L T Transmitter WHO 9 L R Receiver Digital Input 1 gt Digital Output 1 Digital Input 2 gt Digital Output 2 Analogue Setpoint gt Digital Output 3 Analogue input 4 20 mA gt Analog output Thermocouple Input Not used Communication Failure Comes on if no messages from WI I O 9 Setpoint Output Local indication en System OK On if system OK System OK On if system OK WI I O 9 L Transmitter Unit Quick Start v1 7 page 2 of 8 WI I O 9 L Transmitter Unit Quick Start Guide Unit components and connections Your WI I O 9 L T
9. transmitter unit has the following components and terminal connections 8 Da a nw ee Max S0VDC SODOMA Thermocouple type J K or T For inductive load orm signal use surge diodes A Loop powered sensor shown J Externally powered sensors are F also suitable Dl s suitable forvolt free contacts or NPN transistor devices POWER SUPPLY 9 30 VDC SODOMA 12 300mA BIH In order to comply with Electrical Safety Regulations this module must be installed in an Electrical AND Fire enclosure This enclosure may be a single or multiple enclosures Access to the module is to be made by a Service Person only WI I O 9 L Transmitter Unit Quick Start v1 7 page 3 of 8 WI I O 9 L Transmitter Unit Quick Start Guide The front panel contains the following components SMA antenna connector _ at top of unit RS232 configuration 1 M p gt port ra Rotary switch for set point settings The triangle on the rotary switch indicates the current position for example Position 0 Position 1 NOTE To avoid damaging the rotarv switch use a screwdriver to change the position The rotarv switch uses the following setpoint levels WI I O 9 L Transmitter Unit Quick Start v1 7 page 4 of 8 WI I O 9 L Transmitter Unit Quick Start Guide The LEDs on the front panel indicate the unit status Indicates No power supply OK LED Green Current status of the unit OK OK LED Red Fault condition

Download Pdf Manuals

image

Related Search

Related Contents

Clover Electronics LCD2288DVR Flat Panel Television User Manual  Uniden ATLANTIS 250 Two  FD5 Series 650 TV lines      Paquete básico Pentaho Comprehensive Report  Features Parts and Controls Charging the Unit Connecting to    TCRWP AssessmentPro Data Specialist User Manual  GIGABYTE GA-8VM800M User's Manual  

Copyright © All rights reserved.
Failed to retrieve file