portable infrared heater sp-hi1500r/rc/rb
Contents
1. 13 Screw HI1500 14 Free Wheel HI1500 15 Retaining Plate HI1500 16 Nut H11500 17 Zinc Plating Right HI1500 18 Heater Retaining Plate HI1500 19 Quartzose Heating Tube H11500 20 Bellows HI1500 21 TDS H11500 22 Bolt H11500 23 Self drilling Screws H1I1500 24 Air Inlet Fiter Plate H11500 25 Self drilling Screws H11500 26 Screw HI1500 27 Power Cord Bracket HI1500 28 Circuit Breaker HI1500 29 Temperature Sensor 1 HI1500 30 Temperature Sensor 2 H11500 31 Power Cord HI1500 32 Cord Clamp H11500 33 Filter Netting HI1500 34 Thermostat Connecting Line HI1500 35 PCB FPC amp LED Connecting Line H11500 36 Air Outlet Vestee HI1500 37 Screws nether HI1500 38 Screws upper How to rewire fan control 1 Start by removing the back bottom wing nuts on each corner qty2 2 Remove Control Panel amp Display this panel has four clips 2 on top and 2 on bottom the Control Panel is pressed in Once loose place in safe area without removing any of the wiring Clip locations 3 Refer back to the other end of the heater and pull gently Do not to damage the Control Panel attached together 5 Place the back cover with the control plate down on a flat surface and cut the black wire J2 AC_N towards the end where the connector is SIP E SONGLE Ne SLA 1Z2VDC SL C 30A Z50VAC 30VD ele 1 JS H ACL E i 214321 10111 4964 6 Once cut apply electrical tape and zip tie together to red wire to s2. PERATURE ROOM TEM D12 D13 D14 D15 SS he Ne ON S REMOTE CONTROL CO C4 C3 C1 POWER ON OFF C2 INCREASE C3 CLOCK TIMER SET C4 TIMER DELETE C5 TIMER SELECT C6 DECREASE SET DESIRED TEMPERATURE To set the desired temperature that you want the heater to maintain simply press the D3 or the D5 button to move the desired set temp up or down If using the REMOTE simply press the C2 or the C6 to set the temp After a few seconds the set temp display will stop flashing and the heating elements will be turned on In about one minute the fan will be on to delivery warmed air from front vent Note After setting the desired temperature amp the displayed digit stops flashing The actual room air temperature will be displayed To check set temperature at any time by simply press the or button on the control panel or remote control Once the room temperature reaches the desired setting the thermostat will maintain your desired comfort setting by turning the heating elements on and off automatically lf you do not need the heater to run simply press the power on off button D1 or C1 on remote to turn it off The fan will continue to run until the heating elements inside cools down The heater is equipped with an internal safety switch that cuts off power to the infrared heating tubes if airflow is blocked to the unit To restore power to the heat
3. PORTABLE INFRARED HEATER SP HITS00R RC RB OPEN BOX AND ASSEMBLY Porta Del Sol heat packed with 1 Wood cabinet heater x 1 2 Casters x 4 3 Remote control x 1 4 Battery for Remote x 2 5 User manual x 1 6 Warranty card x 1 SPECIFICATION Voltage 120V Frequency 60Hz Current 13A Power 1500W L First please make sure you have removed all the plastic cover from the heater cabinet make sure there is no any project to block air intake and vent Reference our safety instruction and heater placement suggestion to set the heater cabinet L Plug into 120V 60Hz 15Amp or higher Amp US standard household receptacle Please reference our safety instruction LI Turned on the master power switch 1 Front LCD display panel should display you room temperature Using remote control or Front system control panel to set up Please see follow system setup procedure CONTROL SYSTEMS OPERATION GENERAL OPERATION Located on the front of the heater is a control panel display screen Simply press the POWER ON OFF D1 button If using the remote control simply press the POWER ON OFF C1 button and the unit will turn on CONTROL AND DISPLAY PANEL D1 D2 D3 D4D9 D6 D7 D1 POWER ON OFF D2 CLOCK SET TIME SET D3 INCREASE D4 REMOTE SENSOR D5 DECREASE D6 TIMER SELECT D7 TIMER DELETE D8 OFF TIMER D9 ON TIMER D10 OFF TIMER D11 ON TIMER CLOCK SET TEMP TEM
4. ecure it AN 7 A The loose black wire needs to be attached to the white wire J6 HEAT and make contact expose wiring on both ends black and white to meet into spade connector B Push On Terminal used is 16 14 Ga Cal 6 35mm 1 4 Female Disconnect PVC F j E ay C See picture above for J6 HEAT location a 8 Assembly is the reverse of disassembly Make sure Heat sensor wire on back is in place thru the outside of the Heater Housing and not in the inside AEMOTE COerTracn HOLDER
5. ing tubes remove power cord from wall outlet and let the unit cool down for approximately 20 minutes before plugging power cord back into the wall outlet Then perform previous power on procedures If the heater has cooled sufficiently the safety switch will automatically reset and the heating tubes will begin to work again FILTER MAINTENANCE STATIC FILTER SYSTEM The Heater Heating System comes equipped with a lifetime washable static filter which is easy to clean The manufacture recommends the filter be cleaned once a month or as needed To do this follow these steps 1 Remove the filter from the rear of the unit by remove the screws on the filter cover 2 Run warm tap water over the filter the opposite direction of air flow until sufficiently clear or dirt and dust A small amount of mild detergent may be used 3 Shake the filter until excess water is removed 4 Let dry Replace the filter to the rear of the unit Layers of woven polyes fabric Final filter Aluminum collector cell One layer of woven Polyester fabric Pre filter Galvanized lathing Aluminum channel framing Parts Listing Part No Description HI1500 1 LED Display HI1500 2 Wooden Shell HI1500 3 Power Switch H11500 4 Zinc Plating Shell H11500 5 Zinc Plating Left HI1500 6 Nut H1I1500 7 Duct Fan HI1500 8 Nut HI1500 9 Circuit Board H11500 10 Self drilling Screws Hl1500 11 Rear Cover Plate H11500 12 Self drilling Screws H11500
Download Pdf Manuals
Related Search